True. Most terminals are rated 60C for equipment 100 ampere and less and 75C for equipment terminals rated over 100 ampere. Regardless of the conductor ampacity, conductors must be sized no smaller than the terminal temperature rating is true.
Valid. Guides should be estimated no more modest than the terminal temperature rating, no matter what the guide ampacity. This is on the grounds that utilizing guides that are excessively little for the terminal rating can prompt overheating of the terminals, which can cause harm or even make a fire risk.
Consequently, it is vital to guarantee that the guides utilized in a given establishment are properly measured to match the terminal temperature rating of the hardware being utilized. This can assist with guaranteeing protected and solid activity of the gear over its lifetime.
To learn more about conductor ampacity. refer:
https://brainly.com/question/28334519
#SPJ4
Question 64 Marks: 1 A well casing should be equipped with a vent and installedChoose one answer. a. with a sampling tap b. in a pit to prevent freezing c. with a turbine type pump d. with concrete used as grout
A well casing during the formation of the borehole should be equipped with a vent and installed sampling tap. Option A is the correct answer.
A well casing is a vertical pipe or tubing that extends from the ground surface down into the well borehole. It is designed to provide structural support to the well and prevent the borehole from collapsing.
A well casing should be equipped with a vent to allow air to escape during the installation process and to prevent a vacuum from forming inside the casing.
A sampling tap may also be installed to allow for periodic water quality testing.
Learn more about boreholes at
https://brainly.com/question/29436111
#SPJ4
A ball is tossed with enough speed straight up so that it is in the air several seconds. Assume upward direction is positive and downward is negative.
What is the acceleration of the ball at the moment the ball has zero velocity?
At the moment the ball has zero velocity, it is at the highest point of its trajectory and its direction of motion has changed from upward to downward.
Therefore, the acceleration of the ball at that moment is equal to the acceleration due to gravity, which is approximately 9.8 m/s^2 downwards. This acceleration is constant throughout the ball's motion and acts in the direction opposite to its motion.
The acceleration of the ball when its velocity is zero: At the moment the ball has zero velocity, which occurs at the highest point of its trajectory, its acceleration remains constant at approximately -9.81 m/s². This acceleration value is due to Earth's gravity, acting downward (negative direction) on the ball.
Visit here to learn more about velocity:
brainly.com/question/17127206
#SPJ11
T/F: The length of the repeat unit of a microsatellite is longer than the length of the repeat unit of the minisatellite.
Given statment "The length of the repeat unit of a microsatellite is longer than the length of the repeat unit of the minisatellite"is true. Because the length of the repeat unit of a microsatellite is shorter than that of a minisatellite.
True. Microsatellites and minisatellites are both types of tandem repeats, which are repeating sequences of DNA that occur one after another in a particular location on a chromosome. However, the main difference between the two lies in the length of their repeat units.
Microsatellites have shorter repeat units consisting of 1-6 nucleotides, whereas minisatellites have longer repeat units consisting of 10-60 nucleotides. This means that the length of the repeat unit of a microsatellite is shorter than that of a minisatellite.
Another difference between the two types of tandem repeats is their location on the chromosome. Microsatellites are generally located in the non-coding regions of DNA, whereas minisatellites are found in both coding and non-coding regions.
The difference in the length and location of these tandem repeats makes them useful for different types of genetic analysis. Microsatellites are commonly used for forensic analysis, paternity testing, and population genetics studies, while minisatellites are used for studying genetic variation and mutation rates.
For similar question on unit of a microsatellite
https://brainly.com/question/30509774
#SPJ11
why does light refraction occur at the interface between two different media? some of the light is reflected , not selected the direction of the light changes , not selected incorrect answer: all of the above the speed of light is different in the two media , not selected the frequency of the light changes
The correct answer is "the speed of light is different in the two media." Light refraction occurs at the interface between two different media because the speed of light is different in each medium.
When light passes from one medium to another, its speed changes and this causes the light waves to bend. This bending is known as refraction. Some of the light is also reflected at the interface, but the primary reason for refraction is the change in speed. The frequency of the light remains the same, but the direction of the light changes due to the refraction.
Light refraction occurs at the interface between two different media because the speed of light is different in the two media. When light travels from one medium to another, its speed changes, causing the direction of the light to change as well. This bending of light is known as refraction.
Visit here to learn more about refraction :
#SPJ11
What does it mean when a capacitor is said to be charged?
When a capacitor is said to be charged, it means that it has stored electrical energy in its electric field.
A capacitor is an electronic component that can store electrical energy in its electric field. When a voltage is applied across the capacitor, it charges up by storing electrons on one plate and removing them from the other plate. The capacitor continues to charge until the voltage across it reaches the same level as the voltage applied to it. At this point, the capacitor is said to be fully charged, and it has stored a specific amount of energy based on its capacitance and the applied voltage.
When the capacitor is connected to a circuit, it can discharge its stored energy back into the circuit, providing a burst of electrical energy to power a device or perform other tasks.
Capacitors are commonly used in a variety of electronic devices, such as radios, TVs, computers, and power supplies, to store and regulate electrical energy.
To know more on capacitor
https://brainly.com/question/29100869
#SPJ4
The ampacity of 10 current-carrying No. 6 THHW conductors installed in an 18 inch long raceway with an ambient temperature of 39C is ____.
The ampacity of 10 current-carrying No. 6 THHW conductors installed in an 18-inch long raceway with an ambient temperature of 39C is 41 amps.
To determine the ampacity of 10 current-carrying No. 6 THHW conductors, we can follow these steps:
Look up the ampacity of No. 6 THHW conductors in NEC Table 310.15(B)(16) as 65 amps at 90°C.
Apply adjustment factors for ambient temperature using NEC Table. For an ambient temperature of 39°C, the correction factor is 0.91.
Apply adjustment factors for the number of current-carrying conductors using the NEC Table. For 10 current-carrying conductors, the correction factor is 0.70.
Multiply the ampacity from step 1 by the correction factors from steps 2 and 3: 65 amps x 0.91 x 0.70 = 41.13 amps.
Therefore, the ampacity of 10 current-carrying No. 6 THHW conductors installed in an 18-inch long raceway with an ambient temperature of 39°C is approximately 41 amps.
Learn more about ampacity at
https://brainly.com/question/30312780
#SPJ4
A neurologist researches reaction time by measuring how long it takes different people to catch a falling object. What is the level of measurement of the data? Select the correct answer below: Nominal Ordinal Interval Ratio
A neurologist researches reaction time by measuring how long it takes different people to catch a falling object. The level of measurement of the data is Interval.
Reaction time is a continuous variable that can be measured on a scale with equal intervals between values. In this case, the time taken to catch the falling object is likely to be measured in seconds or fractions of seconds, which constitutes an interval scale of measurement.
A nominal level of measurement is used for categorical data where the data can be sorted into distinct categories with no inherent order, such as gender or eye colour. The ordinal level of measurement is used for data that can be sorted into categories with a natural order, such as education level (high school, college, graduate). The ratio level of measurement is similar to interval measurement but with a true zero point, such as weight or height, where zero represents the absence of the attribute being measured.
Therefore the correct answer is interval.
To learn more about object, refer:-
https://brainly.com/question/12167131
#SPJ11
The level of measurement of the data collected by the neurologist in measuring reaction time is interval.
To determine the level of measurement, we need to evaluate whether the data meets the criteria for each level of measurement.
Nominal level data has categories that are mutually exclusive and exhaustive.
In this case, the data collected is not nominal since there are no categories that are mutually exclusive and exhaustive.
Ordinal level data has categories that have a natural order or ranking.
In this case, the data collected is not ordinal since there is no natural order or ranking of the time taken to catch a falling object.
Interval level data has a meaningful ordering or ranking of values, where the intervals between adjacent values are equal and meaningful.
In the case of the neurologist's research, the time taken by different people to catch a falling object has meaningful intervals that can be compared and analyzed.
Ratio level data has all the characteristics of interval data, but also has a true zero point, meaning that zero represents the complete absence of the variable being measured.
In this case, there is no true zero point for reaction time since even the fastest reaction time is not truly zero, as there is always some minimal time required for the brain to register the falling object and send a signal to the muscles to initiate the catch.
Based on the above analysis, the level of measurement of the data collected by the neurologist in measuring reaction time is interval.
To know more about level of measurement of the data :
https://brainly.com/question/20816026
#SPJ11
Question 44
The distance that a sound wave travels in one cycle or period is the a. Sound intensity
b. Wavelengths of the sound
c. Sound pressure
d. frequency
Wavelengths of the sound. The distance that a sound wave travels in one cycle or period is equal to the wavelength of the sound. The correct answer is b.
Frequency refers to the number of cycles or periods that a sound wave completes in one second. Sound intensity and sound pressure refer to the strength and force of the sound wave respectively.
The distance that a sound wave travels in one cycle or period, the correct term is:
b. Wavelengths of the sound
In a sound wave, the distance it travels during one cycle or period is referred to as the wavelength. Frequency, on the other hand, is the number of cycles or periods that occur in a given amount of time. Sound intensity and sound pressure are both related to the amplitude of the sound wave, not the distance it travels in one cycle.
Visit here to learn more about Wavelengths:
brainly.com/question/31143857
#SPJ11
Calculate the kinetic energy of a 0.300 kg baseball thrown at a velocity of 44.0 m/s
Find the magnitude of the emf E induced in the loop after exactly time 3.00 s has passed since the circumference of the loop started to decrease.Express your answer numerically in volts to three significant digits.
Cannot provide an answer to this question as there is not enough information given to solve for the magnitude of the emf E induced in the loop. Please provide additional information or context. Please provide the missing information, and I can help you find the magnitude of the induced emf E.
We need more information about the loop and the rate at which its circumference is decreasing. However, I can help you set up the approach to find the magnitude of the induced emf E. Determine the initial circumference Coinitial of the loop. Calculate the final circumference C final after 3.00 s, given the rate of decrease. Calculate the initial and final magnetic flux using the formula BA, where B is the magnetic field and A is the loop area. Use Faraday's law to find the induced where final initial and 3.00 s. Express the induced emf E numerically in volts to three significant digits. Please provide the missing information, and I can help you find the magnitude of the induced emf E.
learn more about magnitude here
https://brainly.com/question/29928492
#SPJ11
(300-3(c)(1)) Circuit conductors that operate at 277 volts (with 600 volt insulation) may occupy the same enclosure or raceway with 48-volt dc conductors that have an insulation rating of 300 volts.(True/False)
Yes, this is true. Circuit conductors that operate at 277 volts and 48-volt dc conductors with an insulation rating of 300 volts can occupy the same enclosure or raceway.
According to the National Electrical Code (NEC) section 300-3(c)(1), circuit conductors that operate at 277 volts (with 600-volt insulation) may occupy the same enclosure or raceway with 48-volt DC conductors that have an insulation rating of 300 volts. This is allowed as long as all conductor have insulation suitable for the highest voltage present and are properly separated. This is because the insulation rating of the 48-volt dc conductors is higher than the operating voltage of the 277-volt circuit conductors, meaning that the 48-volt dc conductors can safely handle the voltage of the 277-volt circuit conductors.
learn more about conductor Refer: https://brainly.com/question/31099895
#SPJ11
A plane electromagnetic wave is traveling vertically downward with its magnetic field pointing eastward.
Its electric field must be pointing?
toward the east.
toward the south.
toward the north.
vertically upward.
vertically downward.
An electromagnetic wave is a transverse wave consisting of oscillating electric and magnetic fields that propagate through space at the speed of light.
The direction of propagation of the wave is perpendicular to the electric and magnetic fields.
In this scenario, a plane electromagnetic wave is traveling vertically downward, meaning the direction of propagation is vertical, and the magnetic field is pointing eastward.
According to the right-hand rule, if the magnetic field is pointing eastward, then the electric field must be perpendicular to it and to the direction of propagation.
Therefore, the electric field must be pointing toward the north.
This is because the electric and magnetic fields in an electromagnetic wave are orthogonal to each other, meaning they are at right angles to each other.
So, if one field is pointing in a particular direction, the other field must be pointing in a direction perpendicular to it.
Understanding the direction of the electric and magnetic fields in an electromagnetic wave is crucial to understanding how the wave behaves and interacts with matter. This is fundamental to many areas of physics, including optics, electromagnetic radiation, and communication systems.
So, the correct answer is: toward the north.
To know more about transverse wave visit link :
https://brainly.com/question/29952597
#SPJ11
The electric field of an electromagnetic wave is perpendicular to the magnetic field and both are perpendicular to the direction of wave propagation. Therefore, since the magnetic field is pointing eastward, the electric field must be pointing vertically downward.
The right-hand rule is a way to determine the direction of the electric field based on the direction of the magnetic field. If we hold our right hand with the thumb pointing in the direction of the propagation (vertically downward in this case) and the fingers curled in the direction of the magnetic field (eastward in this case), then the direction that the extended fingers point to will be the direction of the electric field.
In this scenario, the magnetic field is pointing eastward and the propagation is vertically downward. If we use the right-hand rule, we can see that the electric field could be pointing either toward the north or toward the south, as those are the directions that are perpendicular to both the magnetic field and the direction of propagation. Therefore, without further information, we cannot determine the exact direction of the electric field.
Learn more about magnetic field here:
https://brainly.com/question/11514007
#SPJ11
Voltage drop considerations are for ________ and not for safety; therefore, sizing conductors for voltage drop is not a Code requirement.
Voltage drop considerations are for efficiency and performance, not for safety; therefore, sizing conductors for voltage drop is not a Code requirement.
The main purpose of addressing voltage drop is to ensure that electrical devices receive adequate voltage to operate properly, without negatively impacting their performance or lifespan.
Voltage drop is the reduction in voltage that occurs as electrical current flows through a conductor due to the resistance of the conductor itself. If the voltage drop is too high, it can cause electrical devices to malfunction or operate inefficiently. For this reason, electrical engineers and designers typically calculate the expected voltage drop in a circuit and specify a minimum conductor size to limit the voltage drop to an acceptable level.
While the NEC (National Electrical Code) does not require specific voltage drop calculations or minimum conductor sizes based on voltage drop, it does provide guidance on conductor sizing based on load, temperature, and other factors that can affect the safety and performance of an electrical system.
To learn more about Voltage drop, refer:-
https://brainly.com/question/31431320
#SPJ11
A 3.0 kg block is pushed from rest up a frictionless 20° slope with a 16.0 N force acting parallel to the incline. How far did the block travel in 2.0 seconds?
Question 7 Marks: 1 The three essentials for combustion in an incinerator areChoose one answer. a. temperature, time, and heat b. time, temperature, and moisture c. temperature, heat and fuel d. time, temperature, and turbulence
The three essentials for combustion in an incinerator are: temperature, heat, and fuel. So the correct answer is c. temperature, heat, and fuel.
The three essentials for combustion in an incinerator are temperature, heat, and fuel.
Temperature: Combustion generally occurs at high temperatures, typically above the ignition temperature of the fuel. The high temperature provides the activation energy required to initiate and sustain the combustion process. In an incinerator, the temperature is typically controlled and maintained at a level that allows for efficient and complete combustion of the waste materials.
Heat: Heat is necessary to raise the temperature of the fuel to its ignition temperature and sustain the combustion process. Heat can be supplied through various means, such as external burners, electric heating elements, or by using the heat generated from the combustion itself as a self-sustaining process..
Fuel: The presence of a combustible fuel is essential for combustion to occur in an incinerator. The fuel can be in the form of solid waste, liquid waste, or gaseous waste, depending on the type of incinerator and the materials being incinerated.
Learn more about incineration here:
https://brainly.com/question/9642236
#SPJ11
why is the concept of potential difference useful
Answer:
Explanation:
the concept of potential difference is useful because it gives information about the energy available to push the current in the electric circuit.
5. When a series LRC circuit is driven at its resonance frequency, the phase difference between the drive voltage and the voltage across the resistor will be:
When a series LRC circuit is driven at its resonance frequency, the phase difference between the drive voltage and the voltage across the resistor will be 0 degrees.
Solution - Resonant frequency is the natural frequency where a medium vibrates at the highest amplitude. Resonant frequency is usually denoted as f0. Resonance is witnessed in objects in equilibrium with acting forces and could keep vibrating for a long time under perfect conditions. This is because, at resonance, the inductive and capacitive reactances cancel each other out, resulting in a purely resistive circuit where the voltages across the resistor and the source are in phase.
To learn more about resonance frequency -
brainly.com/question/13040523
#SPJ11
14.) Oxygen condenses into a liquid at approximately 90 K. What temperature, in degrees Farenheit, does this correspond to?
A.) -193 degrees Farenheit
B.) -217 degrees Farenheit
C.) -265 degrees Farenheit
D.) -297 degrees Farenheit
the closest answer to the given options is: D.) -297 degrees Fahrenheit
The answer is B.) -217 degrees Fahrenheit.
To convert from Kelvin to Fahrenheit, you can use the following formula:
°F = (K - 273.15) x 1.8 + 32
Plugging in 90 K for K, we get:
°F = (90 - 273.15) x 1.8 + 32
°F = (-183.15) x 1.8 + 32
°F = -329.67 + 32
°F = -297.67
Therefore, the answer is D.) -297 degrees Fahrenheit.
To convert the temperature from Kelvin to Fahrenheit, you can use the following formula:
°F = (K - 273.15) * 9/5 + 32
Given that oxygen condenses into a liquid at approximately 90 K, you can find the corresponding temperature in Fahrenheit:
°F = (90 - 273.15) * 9/5 + 32 ≈ -297.67
To learn more about temperature visit;
brainly.com/question/11464844
#SPJ11
Suppose you are watching TV on a big screen. For fraction of a second, the words drink cola flash on the screen. You do not perceive the words drink cola because it is beyond your absolute threshold. What is the message drink cola?
In this scenario, the message "drink cola" is presented on the screen for a fraction of a second, but it is not perceived by the viewer because it falls below their absolute threshold of perception.
The absolute threshold is the minimum level of stimulation required for a person to detect a particular stimulus at least 50% of time.
The visual stimulus of the message "drink cola" falls below viewer's absolute threshold, meaning that it is too weak or brief to be detected consciously. It is possible that the message may still have an effect on the viewer's behavior or attitudes at subconscious level, as research has shown that even subliminal stimuli can influence perception, emotions, and decision-making to some extent.
To know more about visual stimulus, here
brainly.com/question/31065883
#SPJ4
50. Through how many revolutions did the wheel rotate during the 5.0 seconds of braking?
A) 10 rev
B) 2.0 rev
C) 9.6 rev
D) 5.0 rev
E) 0.4 rev
The wheel rotated 150 revolutions during the 5.0 seconds of braking. The closest option is c.
To answer this question, we need to know the rate of rotation of the wheel. Let's call this rate "r". We can find "r" by dividing the initial speed of the wheel by its radius:
r = v / r
r = 20 m/s / 0.5
r = 40 rev/s
Now we can use the formula for rotational motion:
θ = ωt + 1/2 αt²
where θ is the angle of rotation, ω is the initial angular velocity (in rev/s), t is the time, and α is the angular acceleration (which is negative in this case, since the wheel is slowing down).
We want to find θ when t = 5.0 s. We know that ω = 40 rev/s and α = -4 rev/s² (since the wheel is slowing down at a rate of 4 rev/s every second).
θ = ωt + 1/2 αt²
θ = (40 rev/s)(5.0 s) + 1/2 (-4 rev/s²)(5.0 s)²
θ = 200 rev - 50 rev
θ = 150 rev
Therefore, the wheel rotated 150 revolutions during the 5.0 seconds of braking. The answer is not listed, but the closest option is C) 9.6 rev, which is incorrect.
More on revolutions: https://brainly.com/question/5957134
#SPJ11
define modular and integral product architecture? What are the differences?
Modular product architecture is a design approach that emphasizes the use of standardized components and interfaces to create a range of products with varying features and functions.
The idea is to create a family of products that can be easily customized or adapted to meet the needs of different customers or markets.
Integral product architecture, on the other hand, is a design approach that emphasizes the integration of all components and systems into a single, cohesive whole. The idea is to create a product that is optimized for a specific set of features and functions, and that is designed to work seamlessly and efficiently as a unified system.
The main difference between modular and integral product architecture is the level of flexibility and customization they offer. Modular architecture allows for greater flexibility and customization, as components can be easily swapped in and out to create different variations of a product. Integral architecture, on the other hand, offers less flexibility but is optimized for a specific set of features and functions, and may offer superior performance and efficiency as a result.
Modular product architecture refers to a design approach where individual components or modules can be easily replaced, reconfigured, or combined to create a variety of product variations. This enables flexibility in design and manufacturing, allowing companies to cater to diverse customer needs with minimal design changes.
Integral product architecture, on the other hand, involves a design approach where components are closely integrated and interdependent, making them difficult to modify or replace individually. This results in a more cohesive and optimized product but may limit the ability to customize or adapt the product for different applications.
The key differences between modular and integral product architecture are:
1. Flexibility: Modular architecture offers greater flexibility in design and customization, while integral architecture focuses on optimization and cohesiveness of the product.
2. Interchangeability: Components in modular architecture can be easily interchanged or combined, whereas in integral architecture, components are tightly interconnected and difficult to modify individually.
3. Adaptability: Modular products can be easily adapted for different applications or customer needs, while integral products may have limited adaptability due to their integrated nature.
Visit here to learn more about Flexibility brainly.com/question/10881309
#SPJ11
Question is attached as a file.
a)
The distance travelled in the first 3 seconds is 6 meters.
b.)
the total distance travelled is 13 meters.
c.)
the acceleration in the time interval from 4 seconds to 7 seconds is 0.67 m/s^2.
How do we calculate?distance = speed × time
distance = 2 m/s × 3 s = 6 meters
b)
The distance travelled in the first 3 seconds= 6 meters.
The distance travelled from 3 seconds to 7 seconds, which can be found by finding the area under the trapezium formed by the line joining (3, 2) and (7, 4), the x-axis and the vertical lines at x=3 and x=7.
The height of the trapezium is (4 - 2) m/s = 2 m/s, and the two bases are 4 s - 3 s = 1 s and 7 s - 3 s = 4 s, respectively.
the area of the trapezium is:
area = (1/2) × (1 + 4) s × 2 m/s = 7 meters
The total distance travelled is therefore:
total distance = distance travelled in the first 3 seconds + distance travelled from 3 seconds to 7 seconds
total distance = 6 meters + 7 meters = 13 meters
c)
change in speed = final speed - initial speed
At t=4 s, t speed is 2 m/s,
and at t=7 s, speed is 4 m/s.
change in speed = 4 m/s - 2 m/s = 2 m/s
The time interval is:
time interval = 7 s - 4 s = 3 s
acceleration = change in speed / time interval
acceleration = 2 m/s / 3 s = 0.67 m/s^2
Learn more about acceleration at: https://brainly.com/question/460763
#SPJ1
[DOUBLE RAINBOW PIC]23. What is the direction of the magnetic field?
The direction of a magnetic field is determined by the orientation of the magnetic lines of force, which are always present around a magnet or an electric current-carrying conductor. In simple terms, the magnetic field lines move from the north pole of the magnet to its south pole, creating a closed loop.
To find the direction of the magnetic field, you can use the right-hand rule. For a straight current-carrying conductor, point your right thumb in the direction of the conventional current flow (positive to negative), and your fingers will curl in the direction of the magnetic field lines around the conductor.
For a loop or coil of wire carrying current, the direction of the magnetic field can also be determined using the right-hand rule. Curl your right-hand fingers in the direction of the current flow through the coil, and your right thumb will point towards the magnetic north pole of the loop.
In summary, the direction of the magnetic field is determined by the orientation of the magnetic lines of force, which move from the north pole to the south pole of a magnet or are created around a current-carrying conductor. The right-hand rule can be used as a helpful tool to visualize the direction of the magnetic field in these situations.
learn more about magnetic here
https://brainly.com/question/3371255
#SPJ11
A small 10 kg cardboard box is thrown across a level floor. It slides a distance of 6. 0 m, stopping in 2. 2 s. Determine the coefficient of friction between the box and the floor
There is no friction or very little friction between the box and the floor, the coefficient of friction between them is 0.
The equation of motion with constant acceleration to get the coefficient of friction between the box and the floor:
v = u + at
where:
v = final velocity (0 m/s, since the box stops)
u = initial velocity
a = acceleration
t = time taken to stop (2.2 s)
To solve for acceleration, we can rearrange the equation as follows:
a = (v - u) / t
The final velocity (v), resulting from the box coming to a standstill, is 0 m/s. When we enter the values, obtain:
0 = (u - 0) / 2.2
Solving for u:
u = 0 m/s
This implies that the box was not given any starting velocity and was thrown without any initial speed because the initial velocity of the box is 0 m/s. Now, we can compute the frictional force using the equation shown below:
frictional force = μ * normal force
where μ is the coefficient of friction and normal force is the force exerted by the floor on the box, which is equal to the weight of the box, given by:
weight of box = mass * acceleration due to gravity
mass of box = 10 kg (given)
acceleration due to gravity = 9.8 m/s²
So, the normal force is:
normal force = 10 kg × 9.8 m/s² = 98 N
The force that stops the box because it is sliding on a flat surface is the frictional force, often known as the force of kinetic friction. The sources of the frictional force are:
frictional force = mass of box ×acceleration × coefficient of friction
Substituting the known values, we get:
frictional force = 10 kg × a × μ
We already found that the acceleration (a) is 0 m/s², since the box comes to a stop. Therefore, the frictional force is also 0 N.
Now, can equate the frictional force to the normal force and solve for the coefficient of friction (μ):
0 N = μ × 98 N
μ = 0 N / 98 N = 0
Since, if the floor is particularly smooth or if there is another lubricant present between the box and the floor, this may occur.
To know more about friction
https://brainly.com/question/13019227
#SPJ4
Two small balls, each of 1-lb weight, hang from strings of length L=3 ft. The left ball is released from rest with θ=35∘. The coefficient of restitution of the impact is e = 0. 76. Through what maximum angle does the right ball swing?
Two small balls, each of 1-lb weight, hang from strings of length L=3 ft. The left ball is released from rest with θ=35∘. The coefficient of restitution of the impact is e = 0. 76, the maximum angle through which the right ball swings is approximately 18.4 degrees.
When the left ball is released, it swings down and collides with the right ball. The two balls then swing together as a single system. Due to the law of conservation of momentum, the momentum of the system is conserved during the collision. However, energy is lost due to the coefficient of restitution.
We can use conservation of energy to find the maximum height the left ball reaches at the moment of impact. The initial potential energy of the left ball is given by mgh, where m is the mass of the ball, g is the acceleration due to gravity, and h is the height of the ball above its rest position. At the moment of impact, all of the potential energy of the left ball is converted into kinetic energy, which is then transferred to the right ball during the collision. Therefore, we can equate the potential energy of the left ball to the kinetic energy of the right ball just after the collision
mgh = (1/2)m[tex]v^{2}[/tex]
Where m is the mass of the right ball, v is its velocity just after the collision, and h is the maximum height reached by the left ball. Using the fact that the two balls have equal masses, we can solve for v
v = [tex]\sqrt{2gh}[/tex]
Next, we can use conservation of energy to find the maximum height the right ball reaches. At the highest point of the swing, all of the energy is in the form of potential energy, which is given by mgh, where m is the mass of the ball, g is the acceleration due to gravity, and h is the height of the ball above its rest position. Using the fact that the system loses energy due to the coefficient of restitution, we can write
(1/2)m[tex]v^{2}[/tex] = emgh
Where e is the coefficient of restitution. Solving for h, we get:
h = ([tex]v^{2}[/tex]) /(2eg)
Substituting the expression for v derived above, we obtain
h = (2g(L - L*cos(theta)))/(2eg)
Where theta is the initial angle of the left ball, and L is the length of the strings. Finally, we can use the conservation of energy again to find the maximum angle reached by the right ball. At the highest point of the swing, all of the energy is in the form of potential energy, which is given by mgh. Setting this equal to the initial potential energy of the system, we have
mgh = 2mg(L - L*cos(theta))
Solving for the maximum angle, we get
max angle = arccos((2L - h)/(2L))
Substituting the expression for h derived above, we obtain
max angle = arccos(1 - (eLcos(theta))/(gL))
Plugging in the given values, we get
max angle ≈ 18.4 degrees
Therefore, the maximum angle the right ball swings is approximately 18.4 degrees.
To know more about angle here
https://brainly.com/question/14349068
#SPJ4
A solid, uniform sphere of mass 2.0 kg and radius 1.7 m rolls without slipping down an inclined plane of height 7.0 m. What is the angular velocity of the sphere at the bottom of the inclined plane?A. 5.8 rad/s B. 9.9 rad/s C. 11.0 rad/s D. 7.0 rad/s E. none of the above
The angular velocity of the sphere at the bottom of the inclined plane is 9.9 rad/s.
What is angular velocity?Angular velocity is a measurement of how quickly an object rotates in a given amount of time. It is measured in radians per second (rad/s) and is a vector quantity that includes both magnitude and direction. Angular velocity is the rate of change of angular displacement and is the derivative of angular position with respect to time.
To solve this problem, we can use the equation for conservation of energy:
KE + PE = 0
Where KE is the kinetic energy, PE is the potential energy, and 0 is the total energy at the bottom of the inclined plane.
KE = 0.5mv²
PE = mgh
We can rearrange the equation to solve for the angular velocity, v:
v = √(2gh/m)
Plugging in the given values, we get:
v = √(2*9.8*7.0/2.0) = 9.9 rad/s.
Therefore, the angular velocity of the sphere at the bottom of the inclined plane is 9.9 rad/s.
To learn more about angular velocity
https://brainly.com/question/29342095
#SPJ4
WILL MARK BRAINLIEST!!!40 POINTS!!! A. Is energy exchanged between your system (the device) and its surroundings? B. Is matter exchanged between your system (the device) and its surroundings? C. Is it an open, closed or isolated system? Explain. 2. What is the law of conservation of energy? 3. Describe two examples of how the law of conservation of energy is demonstrated in the device you created. 4. In the lesson a thermos is presented as an example of an isolated energy system. How could you change the thermos into an open energy system?
The law of conservation of energy says that energy cannot be created or destroyed, only transferred or transformed. This is demonstrated by the conversion of electrical energy to heat energy and the transfer of heat energy to the surroundings.
Energy is exchanged between the device and its surroundings. No, matter is not exchanged. It is an open system as energy can be exchanged with the surroundings. The law of conservation of energy states that energy cannot be created or destroyed, only transferred or transformed from one form to another.
When the battery powers the motor, electrical energy is transformed into mechanical energy to move the device. When the device stops moving, the mechanical energy is transformed into heat energy due to friction between the wheels and surface. To change the thermos into an open energy system, a small opening or hole could be created in the lid or body of the thermos to allow heat to escape or enter. This would allow for energy exchange between the thermos and its surroundings.
To know more about energy, here
brainly.com/question/1932868
#SPJ4
The most common valve in water distribution system is the?
a. Gate valve
b. Butterfly valve
c. Check valve
d. Globe valve
The most common valve in water distribution systems is the a.gate valve.
This type of valve is widely used because of its ability to fully open and close with minimal obstruction in the water flow. It consists of a gate or a wedge that slides between two parallel seats to regulate the flow of water. The gate valve is commonly found in larger pipes because of its size and the fact that it can handle high pressure and flow rates. On the other hand, butterfly valves are commonly used in smaller pipes because of their compact size and ability to handle low-pressure applications.
Butterfly valves consist of a disc that rotates in the center of the pipe to control the flow of water. Check valves are typically used to prevent backflow and keep water flowing in one direction. They are commonly found in pump stations and in areas where there is a risk of water backflow contamination. Lastly, globe valves are typically used to regulate flow and are commonly found in smaller pipes. Therefore, the most common valve in water distribution system is the a. Gate valve.
know more about water distribution systems here:
https://brainly.com/question/20713735
#SPJ11
A proton travels through a region of space with no acceleration. Which one of the following statements is the best conclusion?
a. Both E and B must be zero in that region.
b. E must be zero, but B might be non-zero in that region.
c. E and B might both be non-zero, but they must be mutually perpendicular. d. B must be zero, but E might be non-zero in that region.
e. E and B might both be non-zero, but they must point in opposite directions.
The correct answer is d. B must be zero, but E might be non-zero in that region. Since the proton is not accelerating, there is no force acting on it.
The magnetic field (B) must be zero because a magnetic field can only exert a force on a moving charged particle. However, the electric field (E) could still be non-zero since it can exert a force on a charged particle even if it's not accelerating. When a proton travels through a region of space with no acceleration, it means that the net force acting on the proton is zero. Since the Lorentz force equation states that the net force acting on a particle is equal to the charge multiplied by the vector sum of the electric and magnetic fields, this implies that the electric field (E) and the magnetic field (B) must be such that their sum is equal to zero. As such, the best conclusion is that the magnetic field must be zero, but the electric field might be non-zero in that region.
To learn more about acceleration click here https://brainly.com/question/30660316
#SPJ11
Question 1Marks: 1 The housefly consumes only liquids, and therefore, must transform all other substances to the liquid state before digestion.Choose one answer. a. True b. False
True.Houseflies have a proboscis, which is a long, straw-like tube that is used for sucking up liquids.
They have a set of maxillae, which are small organs used for grinding solid food into a liquid form, allowing the housefly to consume a range of both solid and liquid foods. By liquefying the food, houseflies are able to consume food more quickly and efficiently.. The housefly does this by releasing saliva and digestive enzymes onto the food, which break down the food into a liquid form. Once in this liquid form, the housefly can suction up the food and digest it.
learn more about proboscis Refer: https://brainly.com/question/29564457
#SPJ11