The ratio of their linear speeds, v2/v1 is 1.2.
To find the ratio of their linear speeds (v2/v1), we will use the relationship between angular velocity (ω), radius (r), and linear speed (v), which is:
v = ω * r
Let v1 be the linear speed of the first motorcycle with a radius r1 = 15 m, and v2 be the linear speed of the second motorcycle with a radius r2 = 18 m. Since both motorcycles have the same angular velocity (ω), we can write the following equations for their linear speed:
v1 = ω * r1
v2 = ω * r2
Now, we want to find the ratio v2/v1. Divide the second equation by the first equation:
(v2/v1) = (ω * r2) / (ω * r1)
The ω terms will cancel out:
(v2/v1) = r2 / r1
Substitute the given values for r1 and r2:
(v2/v1) = 18 m / 15 m
Simplify:
(v2/v1) = 1.2
So the ratio of their linear speeds, v2/v1, is 1.2, which corresponds to option E.
learn more about linear speed Refer: https://brainly.com/question/13100116
#SPJ11
40. A bicycle wheel of radius 0.70 m is rotating at an angular speed of 6.3 rad/s as it rolls on a horizontal surface without slipping. What is the linear speed of the wheel?
A) 1.4 m/s
B) 28 m/s
C) 0.11 m/s
D) 4.4 m/s
E) 9.1 m/s
the linear speed of the wheel is approximately 4.4 m/s.
To find the linear speed of the wheel, we can use the formula:
linear speed = angular speed x radius
In this case, the angular speed is given as 6.3 rad/s and the radius of the wheel is 0.70 m. Plugging in these values, we get:
linear speed = 6.3 rad/s x 0.70 m
linear speed = 4.41 m/s
Therefore, the correct answer is D) 4.4 m/s.
The linear speed of a rotating bicycle wheel can be calculated using the formula:
Linear speed (v) = Angular speed (ω) × Radius (r)
In this case, the radius (r) of the bicycle wheel is 0.70 m, and the angular speed (ω) is 6.3 rad/s. Plugging in the values, we get:
v = 6.3 rad/s × 0.70 m
v ≈ 4.41 m/s
Therefore, the linear speed of the wheel is approximately 4.4 m/s, which corresponds to option D.
learn more about speed here
https://brainly.com/question/8518482
#SPJ11
Question 17
When selecting a location for a sanitary landfill, which is correct?
a. hauling time is more important than hauling distance
b. hauling distance is more important than hauling time
c. disposal site should be located in a remote area
d. land area should provide usage for 5 to 10 years
The correct answer is c. The disposal site should be located in a remote area. This is because a landfill can produce unpleasant odors and can have negative impacts on nearby communities.
Therefore, it is best to locate it in a remote area, away from residential or commercial areas. Hauling distance and time are also important considerations, but the primary concern is finding a suitable location in a remote area. Additionally, the land area should provide enough usage for 5 to 10 years to ensure the landfill is economically viable. Proper planning for hauling and disposal is crucial in ensuring efficient and effective waste managment
to know more about waste managment please vist -
https://brainly.com/question/30051726
#SPJ11
A student presses a .5 kg book against the wall. If the "us" between the book and the wall is .2, what force must the student apply to hold the book in place?
Since the force of static friction can adjust itself up to the maximum value (0.98 N), the student needs to apply a force of at least 4.9 N to hold the book in place against the wall.
A student presses a 0.5 kg book against the wall with the coefficient of static friction (μs) between the book and the wall being 0.2. To hold the book in place, the student must apply a force that is equal to or greater than the force of gravity acting on the book.
The force of gravity (Fg) can be calculated using the equation Fg = m × g, where m is the mass of the book (0.5 kg) and g is the acceleration due to gravity (approximately 9.8 m/s²). So, Fg = 0.5 × 9.8 = 4.9 N (Newtons).
The maximum static friction force (Fs) can be calculated using the equation Fs = μs × Fn, where Fn is the normal force (in this case, equal to the force of gravity). So, Fs = 0.2 × 4.9 = 0.98 N.
Since the force of static friction can adjust itself up to the maximum value (0.98 N), the student needs to apply a force of at least 4.9 N to hold the book in place against the wall.
To know more about static friction click here:
https://brainly.com/question/17237604
#SPJ11
(392-18(B)) Each run of cable tray shall be _____ before the installation of cables.
Each run of cable tray shall be inspected before the installation of cables.
Before the installation of cables, each run of cable tray shall be inspected for any signs of damage or wear. It is important to ensure that all supports are secure, that the tray is properly secured to the supports, and that any bends or turns do not exceed the manufacturer's specified radius. It is also important to check that all cable tie-downs are properly installed, as well as to check for any sharp edges or burrs that may damage the cables. In addition, any unused cable trays should be capped or sealed to prevent dust and debris from entering the tray. Finally, the cable tray should be cleared of any debris or obstructions before cables are installed.
To learn more about cables click here https://brainly.com/question/29644544
#SPJ11
What is the minimum length of time water must remain motionless in service lines prior to first-draw residential lead sampling?
a) 2 hours
b) 4 hours
c) 6 hours
d) 8 hours
The recommended minimum length of time that water should remain motionless in service lines prior to first-draw residential lead sampling is 6 hours.
Lead can leach into drinking water from the service lines and plumbing fixtures, particularly in older homes that may have lead pipes or lead-based solder. When water sits stagnant in these pipes for a period of time, such as overnight or during the day when no one is home, the lead particles that have accumulated in the plumbing system can dissolve into the water. This is why it's important to collect first-draw samples after a period of stagnation.
The EPA recommends a 6-hour stagnation period for collecting first-draw samples from residential plumbing systems because this is typically the longest period of time that water remains stagnant in home plumbing systems. This means that the water has been sitting in the pipes long enough to allow any lead particles to leach into the water, but not so long that the water quality may be affected by other factors, such as microbial growth or chemical reactions.
It's important to note that first-draw samples are used to identify the presence of lead in the plumbing system, but they may not be representative of the actual exposure to lead that a person may experience. This is because the lead concentration in the water can vary depending on factors such as the age and condition of the plumbing system, the water chemistry, and the length of time that water has been sitting in the pipes.
Visit to know more about Lead :-
brainly.com/question/14512284
#SPJ11
An atom of the isotope 137Ba consists of how many protons (p), neutrons (n), andelectrons (e)?A) 56 p, 137 n, 56 e D) 56 p, 56 n, 56 eB) 56 p, 81 n, 56 e E) 81 p, 56 n, 81 eC) 137 p, 81 n, 56 e
The answer is B) 56 p, 81 n, 56 e. This is because the isotope 137Ba has a mass number of 137, which is the sum of its protons and neutrons.
Since the atomic number of barium (Ba) is 56, this means that there are 56 protons in the nucleus of this isotope.
To find the number of neutrons, we can subtract the number of protons from the mass number:
137 - 56 = 81
Therefore, there are 81 neutrons in the nucleus of this isotope.
Isotopes are atoms of an element with varying atomic masses but the same atomic number, meaning they have different numbers of neutrons but the same number of protons and, consequently, the same chemical characteristics.
Radioisotopes, as well as stable and unstable isotopes, can exist.
Therefore, a radioisotope is a chemical element with an unstable nucleus, or one with an unbalanced ratio of protons to neutrons. As a result, until this element reaches stability, it emits ionising radiation as a way of dissipating its surplus energy.
The unstable form of an element that releases radiation to change into a more stable form is known as a radioisotope, to put it simply.
Finally, because the atom is neutral (meaning it has no overall charge), it must also have 56 electrons, since the number of electrons in an atom is equal to the number of protons in the nucleus.
Learn more about Radioisotopes here
https://brainly.com/question/28039996
#SPJ11
Question 14
Slight, irreversible hearing loss may result for many people, from daily exposure over an 8 hour period of time to sound averaging:
a. 55 dB
b. 65 dB
c. 75 dB
d. 85 dB
The correct answer is d. 85 dB. Slight, irreversible hearing loss may result from daily exposure to sound averaging 85 dB over an 8 hour period of time.
It is important to protect your hearing by limiting exposure to loud sounds and wearing hearing protection when necessary. At 85 dB, there is a high risk of developing hearing loss from exposure over an 8 hour period. According to OSHA, the permissible exposure limit for continuous noise exposures is 90 dB for 8 hours. Therefore, exposure to 85 dB for 8 hours is considered to be highly risky and could potentially lead to a slight, irreversible hearing loss.
To learn more about sound click here https://brainly.com/question/31176646
#SPJ11
what are some difficulties in describing the motion of a pendulum using newton's laws instead of the principle of conservation of energy?multiple select question.the weight force varies in magnitudethe tension force varies in magnitudethe tension force varies in directionthe weight force varies in direction
The weight force acting on the pendulum varies in magnitude as it moves through its arc, as does the tension force of the string.
Describing the motion of a pendulum using Newton's laws can be challenging due to the following reasons:
1. The tension force varies in magnitude: As the pendulum swings, the tension force in the string changes depending on the angle of the swing, which affects the net force acting on the pendulum.
2. The tension force varies in direction: The direction of the tension force also changes as the pendulum swings back and forth. This changing direction makes it more difficult to apply Newton's laws directly to the problem.
3. The weight force varies in direction: While the weight force (gravity) remains constant in magnitude, its direction relative to the pendulum's motion changes throughout the swing. This change in direction adds complexity to the analysis of the pendulum's motion using Newton's laws.
By using the principle of conservation of energy, these challenges can be circumvented, as it allows for a more straightforward analysis of the pendulum's motion without needing to consider the varying forces acting on the system.
To learn more about motion click here https://brainly.com/question/22810476
#SPJ11
greenhouse gases transmit visible light, allowing it to heat the surface, but then absorb infrared light from the earth's surface, trapping the heat near the surface. true or false
True. Greenhouse gases are gases that can trap heat within the Earth's atmosphere.
They allow visible light to pass through them and reach the Earth's surface.
Once this light reaches the surface, it is absorbed by the land, oceans, and vegetation, causing them to heat up.
However, once the surface has been heated, it begins to radiate heat back into the atmosphere in the form of infrared radiation.
Greenhouse gases such as carbon dioxide, methane, and water vapor are very effective at absorbing this infrared radiation, trapping the heat near the Earth's surface. This is known as the greenhouse effect, and it is the reason why the Earth's average temperature is approximately 15°C (59°F), making it hospitable to life.
However, human activities, particularly the burning of fossil fuels, have increased the levels of greenhouse gases in the atmosphere, which has led to an enhanced greenhouse effect.
This enhanced greenhouse effect has caused the Earth's average temperature to increase, leading to a range of impacts, including rising sea levels, more frequent and severe weather events, and changes in ecosystems.
To address this issue, it is crucial to reduce greenhouse gas emissions and transition towards cleaner, more sustainable energy systems.
This includes measures such as investing in renewable energy, improving energy efficiency, and transitioning away from fossil fuels.
By taking action to reduce greenhouse gas emissions, we can help to protect the planet and ensure a livable future for generations to come.
To know more about Earth's atmosphere visit link :
https://brainly.com/question/13154099
#SPJ11
5. When an aluminum rod is placed in the middle of an inductor, the resonance frequency of the LRC circuit should
When an aluminum rod is placed in the middle of an inductor, the resonance frequency of the LRC circuit should: decrease
The inductance of an inductor depends on its physical dimensions and the material it is made of. Placing an aluminum rod in the middle of an inductor changes its effective inductance due to the presence of the conductive material. Since the effective inductance is reduced, the resonance frequency of the LRC circuit is decreased. This is because the resonance frequency depends on the values of the inductance, capacitance, and resistance in the circuit, and a decrease in inductance results in a decrease in the resonance frequency. This effect can be utilized in various applications, such as in proximity sensors and metal detectors.
Learn more about LRC circuit here:
https://brainly.com/question/29045377
#SPJ11
Suppose you exert a force of 2,800 N to lift a desk up onto a porch. But if you use a ramp, you need to exert a force of only 1,400 N to push it up the ramp onto the porch. What is the mechanical advantage of the ramp?
The force needed to raise an object without a ramp and the force needed to push it up a ramp can be used to calculate the mechanical advantage of a ramp. In this instance, 2,800 N of force is required to elevate the desk without the ramp. But when using the ramp, it can be pushed up with just 1,400 N of effort.
To determine mechanical advantage, divide the input force by the output force. In this case, the input force is 2,800 N without the ramp, while the output force is 1,400 N with the ramp. In light of this, the mechanical benefit of the ramp can be calculated as follows:
Input force minus output force is the mechanical advantage.
1,400 N x 2,800 N = mechanical advantage
Advantage mechanical = 0.5
As a result, the ramp in this situation has a mechanical advantage of 0.5. In other words, the ramp cuts down the force needed to elevate the desk by a factor of 0.5 or 1:2.
For more such question on force
https://brainly.com/question/28356470
#SPJ11
One is a bun, two is a shoe, three is a tree, etc. is an example of what?
Answer:
A popular set of Peg-Words
What is a Peg-Word?
They're easy to remember because they rhyme with the names of the first ten natural numbers, is: one is a bun, two is a shoe, three is a tree, four is a door, five is a hive, six is sticks, seven is heaven, eight is a gate, nine is wine, ten is a hen.
: Our burning of fossil fuels for energy poses several different problems. Describe what is generally considered the biggest problem and the main reason for using alternatives.
The biggest problem posed by burning fossil fuels is the emission of greenhouse gases, primarily carbon dioxide, which contributes to global climate change.
Fossil fuels, such as coal, oil, and natural gas, are non-renewable sources of energy that have been widely used for centuries. However, the combustion of these fuels releases carbon dioxide and other greenhouse gases into the atmosphere, which trap heat and contribute to global climate change.
The resulting impacts of climate change, such as rising sea levels, more frequent and severe weather events, and the spread of diseases, have serious environmental, economic, and social consequences. Therefore, finding alternatives to fossil fuels, such as renewable energy sources like solar, wind, and hydropower, is crucial to mitigate the effects of climate change and ensure a sustainable future.
To know more about fossil fuels, here
brainly.com/question/3371055
#SPJ1
A skier is being towed up a snow-covered hill by a tow rope. What forces are being exerted on the skier?
When a skier is being towed up a snow-covered hill by a tow rope, several forces come into play. The primary force acting on the skier is the tension force exerted by the tow rope. This force pulls the skier forward, enabling them to move uphill.
At the same time, the skier experiences a resistance force due to the friction between their skis and the snow surface. This force acts in the opposite direction to the tension force, causing the skier to slow down or stop if the tension force is not strong enough.
In addition to these forces, the skier also experiences a gravitational force pulling them downwards. This force affects the skier's trajectory and can cause them to slide downhill if they lose control or the tension force is suddenly released. Overall, the forces exerted on the skier when being towed up a snow-covered hill can be complex and require a combination of physical factors to be considered. However, understanding the basic forces involved can help skiers to navigate the terrain safely and effectively.\
For more information on gravitational force see:
https://brainly.com/question/12528243
#SPJ11
If, prior to applying the pads, you see a medication patch on the person's chest you should--
Remove it with gloved hands
Leave the patch on the chest and place the AED pads on chest even if they touch the patch.
Leave the patch on the chest and place the AED pads around the patch so they don't touch the patch.
Remove the patch using no gloves.
Remove the patch with gloved hands before applying the AED pads to the person's chest. It is important to ensure that the chest is clean and dry before applying the AED pads to maximize their effectiveness.
AED pads (automated external defibrillator pads) are adhesive pads that are placed on a person's chest to deliver an electric shock in the event of sudden cardiac arrest (SCA). AED pads are an important component of an AED, which is a portable medical device used to treat people experiencing cardiac arrest. AED pads are typically sold in pairs, with one pad placed on the upper right chest and the other on the lower left side of the chest. The pads contain sensors that analyze the person's heart rhythm and determine whether a shock is needed. If a shock is required, the AED delivers a controlled electric shock to the heart through the pads to restore a normal heart rhythm. The AED pads are designed to be easy to use and are equipped with clear visual and audio instructions to guide the user through the process of applying them to the person's chest. The pads are also designed to be compatible with different types of AEDs, making it easy to replace or upgrade them if needed.
Learn more about AED pads here:
https://brainly.com/question/30759441
#SPJ11
Question 26
What statement concerning ozone is incorrect?
a. Ozone residual can last several hours
b. Ozone is faster disinfectant than chlorine
c. Ozone is more expensive than chlorine
d. All statements are correct
Regarding ozone, option D: all statements are correct as it is a faster disinfectant than Chlorine, more expensive and also its residuals can last more than several hours.
In the upper stratosphere of the atmosphere, UV rays split oxygen into separate oxygen or nascent oxygen. Other oxygen molecules combine with these nascent oxygen atoms to form ozone. Ozone forms a protective layer of earth that protects us from harmful UV radiations. Hence, it is necessary to maintain the ozone layer. The reaction occurs as follows:
O₂ + UV rays → 2O
O₂ + O → O₃
Ozone layer is thermodynamically unstable and hence decomposes to molecular oxygen. CFCs or freons, non-organic molecules are known responsible for its depletion. It is obviously more expensive and a better disinfectant than chlorine.
To know more about ozone formation, refer:
https://brainly.com/question/9027271
#SPJ4
Directions Concept Builder Charge and Charging
The foam square become charged because C, Electrons were removed from it.
What makes a fur or foam charged?Electrons can move from one material to the other when two dissimilar materials are rubbed together, leading to an unbalanced charge. One substance may become positively charged as a result of losing electrons, while the other acquires electrons and becomes negatively charged.
The foam square and animal fur in this experiment had a negative charge on the foam and a positive charge on the fur due to the flow of electrons between the two materials due to friction.
Find out more on Charge here: https://brainly.com/question/18102056
#SPJ1
(332-40(B)) Where MI cable terminates, a _____ shall be provided immediately after stripping to prevent the entrance of moisture into the insulation.
Where MI cable terminates, a seal shall be provided immediately after stripping to prevent the entrance of moisture into the insulation.
When terminating MI (mineral-insulated) cable, we need to ensure that the cable is properly sealed to prevent the ingress of moisture into the insulation. Moisture can cause corrosion, breakdown of the insulation, and other problems that can compromise the safety and integrity of the cable.
To prevent this, a seal should be provided immediately after stripping the cable. The seal should be applied securely and in accordance with the manufacturer's instructions to ensure that it provides an effective barrier against moisture ingress.
To know more on National Electrical Code
brainly.com/question/17215290
#SPJ4
Question: Does the length of the paper helicopter rotors effect the speed at which it falls to the ground? (Don't answer this!)
Real question: what are 4 constants? (what must remain the same)
There are many constants in mathematics and physics, but here are four commonly known ones:
The speed of light in a vacuum, denoted by "c", which is approximately 299,792,458 meters per second.The gravitational constant, denoted by "G", which is approximately 6.674 x 10^-11 cubic meters per kilogram per second squared.Avogadro's number, denoted by "N_A", which is approximately 6.022 x 10^23 particles per mole.Planck's constant, denoted by "h", which is approximately 6.626 x 10^-34 joule-seconds.What are constants?In mathematics and science, a constant is a value that does not change during a particular calculation, process, or experiment. Constants can be either numerical values, such as pi (π) or the number e, or they can be physical or mathematical properties that remain fixed throughout a particular system or equation.
Learn about gravitational constant here https://brainly.com/question/29840517
#SPJ1
When a vehicle's speed doubles, how much more distance does it need to stop?
This means that if a vehicle needs 50 feet to stop at a speed of 20 mph, it will need 200 feet to stop at a speed of 40 mph.
What is speed?Speed is a measure of the rate of motion, or the rate of change in position of an object. It is represented by the distance an object travels in a given amount of time. Speed is usually measured in kilometres per hour, metres per second, or miles per hour. It is a scalar quantity, meaning it has magnitude but not direction. Speed is a physical quantity, meaning that it is measurable and can be calculated. Factors such as force, acceleration, and time can influence the speed of an object.
When a vehicle's speed doubles, the distance it needs to come to a complete stop increases fourfold. This is because the stopping distance is proportional to the square of the speed: if the speed is doubled, the distance needed to come to a complete stop increases by a factor of four. This means that if a vehicle needs 50 feet to stop at a speed of 20 mph, it will need 200 feet to stop at a speed of 40 mph.
To learn more about speed
https://brainly.com/question/3004254
#SPJ4
When can an electric field that does not vary in time arise?
An electric field that does not vary in time can arise when the charges creating the field are stationary or are moving at a constant velocity.
In other words, if the charges are not accelerating, then the electric field they create will not vary in time. However, if the charges are accelerating or changing direction, then the electric field will vary in time. An electric field that does not vary in time, also known as a static electric field, can arise when there is a constant distribution of electric charges or when the charges are not in motion. In this scenario, the electric field remains constant over time because the charges' positions and magnitudes do not change.
To learn more about electric field click here https://brainly.com/question/15800304
#SPJ11
how can the phase rotation of one alternator be changed in relationship to the other alternator?
To change the phase rotation of one alternator in relation to another alternator, you can employ the following steps:
1. First, ensure both alternators are properly synchronized. Synchronization is necessary to maintain phase relationships and avoid disturbances in the power system.
2. To alter the phase rotation, you can reverse the field current direction in one of the alternators. This can be achieved by swapping the connections to the field winding. The alternator with the reversed field current will now have an opposite phase rotation compared to the other alternator.
3. When connecting the two alternators in parallel, ensure their voltage magnitudes, frequencies, and phase angles are matched. Use a synchroscope or phase sequence indicator to confirm the phase rotation and synchronization.
4. Once the phase rotation is changed, monitor the alternators' operation. Observe the load-sharing behavior and make necessary adjustments to the prime mover's speed or the alternator's excitation to ensure proper load distribution.
5. Finally, continuously verify the phase rotation during operation. Any changes in load or system conditions can affect the phase relationship between the alternators. Regular monitoring ensures a stable and efficient power system.
By following these steps, you can effectively change the phase rotation of one alternator in relation to another while maintaining proper synchronization and system stability.
to know more about phase rotation refer here:
https://brainly.com/question/30780859#
#SPJ11
To change the phase rotation of one alternator in relation to the other alternator, the connection between the two must be adjusted. This can be done by swapping the connection of any two of the three-phase wires.
The phase rotation of an alternator is determined by the sequence in which the phases are connected to the system. One way to change the phase rotation is to swap any two of the three phase connections of the alternator. This is known as interchanging two phases. For example, if phases A and B are connected to the power system and the phase rotation is ABC, swapping phases A and B will change the phase rotation to ACB.
By doing so, the phase sequence will be reversed, effectively changing the phase rotation. It's important to note that changing the phase rotation of one alternator can affect the overall performance of the electrical system, so it's important to consult with a qualified electrician or engineer before making any changes.
Learn more about power system here:
https://brainly.com/question/28528278
#SPJ11
42. A car is moving along a horizontal road at a constant velocity that is directed 45° south of east. What is the direction of the angular velocity of the wheels of the car?
A) 45° south of west
B) 45° north of west
C) 45° south of east
D) 45° north of east
E) due east
The direction of the angular velocity of the wheels of the car is the same as the direction of the velocity of the car, which is 45° south of east. Therefore, the answer is C) 45° south of east.
The direction of the angular velocity of the wheels of the car is perpendicular to the plane of rotation. In this case, since the car is moving along a horizontal road, the wheels are rotating in a horizontal plane. Therefore, the angular velocity will have a direction perpendicular to this horizontal plane, which is vertically upwards or downwards. However, the given options do not include vertical directions, so we can assume that the question intends to ask for the direction of the linear velocity of a point on the rim of the wheel (the tangential velocity), which is parallel to the horizontal plane.
To learn more about angular velocity click here https://brainly.com/question/29557272
#SPJ11
A device that is usually factory built, or consisting of silicone foam, mortar, fire resistive board, wire mesh, and collars or clamp bands, and are typically installed as part of a penetration through a wall or ceiling/floor assembly is called a
A device that is usually factory built, or consisting of silicone foam, mortar, fire resistive board, wire mesh, and collars or clamp bands, and are typically installed as part of a penetration through a wall or ceiling/floor assembly is called a firestop.
A firestop is a system or device that is installed in a building to prevent the spread of fire through openings in walls, floors, and ceilings. It is designed to maintain the fire resistance rating of a fire-rated wall or floor assembly by sealing the openings created by pipes, ducts, or cables that penetrate through it.
Firestops are usually factory-built devices or can be made of materials like silicone foam, mortar, fire resistive board, wire mesh, and collars or clamp bands that are assembled on site.
The main purpose of a firestop is to prevent the spread of fire and smoke through openings in a building. It does this by blocking the passage of flames and heat through penetrations in walls, floors, and ceilings. Firestops are typically tested and certified by third-party testing agencies to ensure that they meet specific fire resistance and smoke control requirements.
By installing firestops in a building, the risk of fire and smoke spread can be significantly reduced, providing occupants with more time to evacuate and increasing the chances of saving lives and property.
To know more about firestop, refer here:
https://brainly.com/question/30144225#
#SPJ11
1. What is the final temperature of two cups of water being mix together? Cup 1 mass is 150
kg and has a temperature of 30 degrees Celsius; Cup 2 mass is 250 kg and has a temperature of
75 degrees Celsius. Specific heat for water (4186)
The final temperature of the two cups of water being mixed together, given that one cup has a temperature of 30 °C and the other has 75 °C, is 58.13 °C
How do i determine the final temperature of the two cups?To obtain the final temperature of the two cups of water, we must obtain the equilibrium temperature of the two cups of water mixture. Details below:
Mass of water in cup 1 (M) = 150 KgTemperature of water in cup 1 (T) = 30 °CMass of water in cup 2 (Mᵥᵥ) = 250 KgTemperature of water in cup 2 (Tᵥᵥ) = 75 °CSpecific heat capacity of the water = 4186 J/KgºC Equilibrium temperature (Tₑ) =?Heat loss by cup 2 = Heat gain by cup 1
MᵥᵥC(Tᵥᵥ - Tₑ) = MC(Tₑ - T)
250 × 4186 (75 - Tₑ) = 150 × 4186(Tₑ - 30)
1046500(75 - Tₑ) = 627900(Tₑ - 30)
Clear bracket
78487500 - 1046500Tₑ = 627900Tₑ - 18837000
Collect like terms
78487500 + 18837000 = 627900Tₑ + 1046500Tₑ
97324500 = 1674400Tₑ
Divide both side by 1674400
Tₑ = 97324500 / 1674400
Tₑ = 58.13 °C
From the above calculation, the equilibrium temperature is 58.13 °C.
Thus, we can conclude that the final temperature of the two cups of water is 58.13 °C
Learn more about temperature:
https://brainly.com/question/14281142
#SPJ1
how do the minute ventilation (ve) values change during exercise? why does this occur? heart rate increases with exercise as well. how does this relate to external respiration?
The body's increased need for oxygen, which arises because the muscles need more oxygen to make energy, causes an increase in the minute ventilation (Ve) values.
During exercise, the minute ventilation (Ve) values increase due to the body's increased demand for oxygen. This occurs because the muscles require more oxygen to produce energy, and therefore, more carbon dioxide is produced as a byproduct. The increased Ve allows for the removal of excess carbon dioxide and the delivery of additional oxygen to the working muscles.
The increase in heart rate during exercise is directly related to ventilation as the heart pumps more blood to deliver oxygen and remove carbon dioxide. The increased heart rate and ventilation also work together to improve external respiration, which is the exchange of gases between the lungs and the environment. With the increased Ve and heart rate, more oxygen can be taken in, and more carbon dioxide can be eliminated, allowing for more efficient external respiration.
To learn more about minute ventilation, refer:-
https://brainly.com/question/4441038
#SPJ11
During exercise, the demand for oxygen and energy increases, which leads to an increase in the body's metabolic rate.
The increase in metabolic rate results in an increase in the amount of carbon dioxide produced by the body.
To maintain the balance of oxygen and carbon dioxide in the body, minute ventilation (Ve) values increase. Minute ventilation is the volume of air breathed in and out of the lungs per minute.
The increase in Ve values during exercise is primarily due to an increase in tidal volume, which is the amount of air inspired or expired during each breath, and to a lesser extent, an increase in respiratory rate.
The increase in tidal volume allows for more oxygen to be taken in and more carbon dioxide to be expelled from the body.
Heart rate also increases during exercise to meet the increased oxygen demand of the body.
The increase in heart rate is due to sympathetic nervous system activation, which stimulates the release of adrenaline and noradrenaline, leading to increased heart rate and cardiac output.
The increased heart rate facilitates the delivery of oxygen to the muscles and other organs, helping to meet the increased demand.
These changes in minute ventilation and heart rate during exercise are closely related to external respiration.
External respiration is the process by which oxygen is taken up by the lungs and carbon dioxide is expelled from the lungs.
The increase in Ve and heart rate facilitate the exchange of gases between the lungs and the environment, leading to increased oxygen uptake and carbon dioxide elimination.
In summary, the increase in minute ventilation and heart rate during exercise is necessary to meet the increased demand for oxygen and energy in the body.
These changes are closely related to external respiration, which facilitates the exchange of gases between the lungs and the environment, leading to increased oxygen uptake and carbon dioxide elimination.
To know more about minute ventilation :
https://brainly.com/question/4441038
#SPJ11
The active elements of the fractal computation are the pixels.true/false
True. The active elements of fractal computation are indeed the pixels, which are the individual units that make up a digital image.
Fractal computation involves performing complex calculations and iterations on these pixels to generate the intricate patterns and structures that characterize fractals.
True. In the context of fractal computation, the active elements are the pixels, as they represent the individual data points that are calculated and displayed to form the fractal image.
To know more about Elements click here .
brainly.com/question/13025901
#SPJ11
the cardiovascular control center in the medulla receives input from the __________.
The cardiovascular control center in the medulla receives input from the glossopharyngeal and vagus nerves.
The cardiovascular control center in the medulla receives input from various sources, including the baroreceptors, chemoreceptors, and proprioceptors.
These receptors provide information about blood pressure, oxygen levels, and body position to the cardiovascular control center, which then sends out appropriate signals to regulate heart rate, blood pressure, and other cardiovascular functions.
The glossopharyngeal and vagus nerves supply it with sensory information regarding blood pressure and cardiac function, and its output triggers sympathetic stimulation of the heart or blood vessels through the upper thoracic lateral horn.
To know more about cardiovascular control center here:
https://brainly.com/question/31246821#
#SPJ11
Glossopharyngeal and vagus nerves provide input to the medulla's cardiovascular control centre.
Baroreceptors, chemoreceptors, and proprioceptors are a few of the sources of information that the cardiovascular control centre in the medulla gets.
The cardiovascular control centre receives information from these receptors regarding blood pressure, oxygen levels, and body posture and uses that information to deliver the proper signals to control heart rate, blood pressure, and other cardiovascular processes.
It receives sensory information about blood pressure and cardiac function through the glossopharyngeal and vagus nerves, and its output causes sympathetic stimulation of the heart or blood vessels through the upper thoracic lateral horn.
learn more about cardiovascular control centre here:
https://brainly.com/question/31246821
#SPJ11
Question 49 Marks: 1 The volume of the dose from a properly sized dosing tank should be equal to:Choose one answer. a. 20% of the volume of the lines dosed b. 40% of the volume of the lines dosed c. 60% of the volume of the lines dosed d. 100% of the volume of the lines dosed
The correct answer is d. 100% of the volume of the lines dosed. The dosing tank should be properly sized to ensure that the entire volume of the lines being dosed is covered by the dose. This ensures accurate and effective dosing.
Biologically effective radiation dose, appropriate for relating doses to effects on the human body, is the absorbed dose in gray. The biologically effective radiation dose, or the amount of radiation energy absorbed by an organism.
When studying the effects of radiation on humans, the most appropriate measure of radiation dose is the absorbed dose in Gray (Gy). Gray is a unit of measure that corresponds to the amount of energy absorbed by an organism per kilogram of tissue. It is the most accurate way of determining the amount of energy absorbed by a person, which is essential for assessing the risks associated with radiation exposure.
Visit here to learn more about effective dosing : https://brainly.com/question/30077631
#SPJ11
Given a parallel runtime of 20s on eight cores and a serial runtime of 80s, what is the runtime in seconds on 16 cores assuming the same efficiency (do not include any units in the answer)?
If we assume the same efficiency, then we can use Amdahl's Law to calculate the new runtime on 16 cores.
Amdahl's Law states that the speedup of a parallel program is limited by the portion of the program that must be executed sequentially. In this case, the portion that must be executed sequentially is (80-20)/80 = 0.75 or 75%. This means that only 25% of the program can be parallelized. Therefore, the speedup we can expect from doubling the number of cores is limited to 1/((1-0.25) + 0.25/8) = 1.85.
Using this speedup, we can calculate the new runtime on 16 cores as 20/1.85 = 10.81 seconds.
To learn more about runtime click here https://brainly.com/question/13182494
#SPJ11