Which one of the following timer parameters determines the time duration for the timing circuit?a. Accumulated time.c. Timer address.b. Preset time.d. Time base.

Answers

Answer 1

The parameter that determines the time duration for the timing circuit in a timer is the preset time. Option b is answer.

The preset time is the value that is set in the timer to determine how long the timing circuit should run before the timer's output changes state. When the timer receives an input signal, it begins counting down from the preset time to zero. Once the timer reaches zero, the output changes state.

The other options listed are also timer parameters, but they do not directly determine the time duration for the timing circuit:

Accumulated time: This is the total time that the timer has accumulated since it was last reset. It is not used to determine the time duration for the timing circuit, but rather to keep track of how much time has elapsed since the timer was last reset.

Timer address: This is the address of the timer in the PLC's memory. It is not directly related to the time duration for the timing circuit.

Time base: This is the interval at which the timer updates its count. It is not used to determine the time duration for the timing circuit, but rather to set the resolution of the timer.

Option b is answer.

You can learn more about timer at

https://brainly.com/question/14316896

#SPJ11


Related Questions

Which instruction can best be used to turn an output coil on or off after the ring has been false for a desired time?a. RTOC.ON OR ONOFb. TONd TOF

Answers

The instruction that can best be used to turn an output coil on or off after the ring has been false for a desired time is the TOF (Timer Off Delay) instruction. Option D.

The TOF instruction turns on an output coil after a timer has timed out, which occurs when the timer has been enabled and the preceding logic has been false for a desired time.

This instruction is commonly used in applications where a process must be started or stopped after a specific time delay.

Option D (TOF) is the correct answer.

Option A (RTOC.ON OR ONOF) is not a valid instruction in most PLC programming languages, and option B (TON) is used to turn on an output coil after a timer has been enabled and the preceding logic has been true for a desired time.

For similar questions on Desired Time

https://brainly.com/question/15585705

#SPJ11

Which keys act as a hot key combination that is used to interrupt an IOS process?

Answers

The hot key combination used to interrupt an IOS process is Control + C. This key combination sends a signal to the operating system, causing it to halt the current process and return to the command prompt.

Client, because they are a part of the server operating system request line. The client asks for a request for information or data from the provider (the server) and the server provides this to its client (the desktop computer). They work together hand in hand one is recieving information and one is sending information.Network Operating System is operated on a firewall, router, or switch, so answer option (B) is accurate.

A firewall is basically the barrier that stands between a private internal network and the open Internet at its most basic level. The primary function of a firewall is to let safe traffic in while blocking dangerous traffic.

Since a gateway serves as a home network's primary conduit to the Internet, it also serves as a firewall. For privacy protection, a firewall should be installed on every residential network.

Learn more about operating system here

https://brainly.com/question/30778007

#SPJ11

his voltage reading was obtained while cranking the engine. the indicated reading (0.816 v) is _

Answers

The voltage reading was taken while cranking the engine, and the indicated reading was 0.816 volts. To provide an explanation with the terms:


When cranking the engine, the starter motor requires a certain amount of voltage to function properly. The voltage reading of 0.816 volts indicates the electrical potential difference present at that specific point during the engine cranking process.

To determine whether this voltage reading is within the acceptable range, you would need to compare it to the manufacturer's specifications for the particular engine being tested. If the reading is within the specified range, the engine's electrical system is functioning properly. If it is outside the acceptable range, further investigation may be required to identify any potential issues with the engine's electrical components.

Learn more about voltage here:

brainly.com/question/2364325

#SPJ11

Hi! Based on the information provided, the voltage reading obtained while cranking the engine was 0.816V. This indicated reading signifies the voltage level present during the engine cranking process.

Learn more about cranking the engine: https://brainly.com/question/14800055

#SPJ11

QUESTION 2
After two technicians examine a broken and disintegrated DPF, Technician A says that the filter damage was caused by water
contamination of an ash-loaded filter. Technician B says that the filter was damaged by back-to-back regenerations that occurred
too frequently. Who is correct?
O a. Technician A
O b. Technician B
O c. Both Technician A and Technician B.
O d. Neither Technician A nor Technician B
QUESTION 3
Technician A says that the diesel exhaust oxidation catalysts used by diesel engines are like the ones that have been used in
automobiles for the last 2 decades. Technician B says that diesel exhaust oxidation catalysts store noxious emissions in the substr
when the exhaust temperatures are low. Who is correct?
O a. Technician A
O b. Technician B
O c. Both Technician A and Technician B
O d. Neither Technician A nor Technician B

Answers

Answer:

2:C 3:B

Explanation:

2. It is difficult to determine who is correct without additional information or context about the situation. Both Technician A and Technician B offer plausible explanations for the cause of the filter damage, and it is possible that both factors contributed to the problem. Therefore, the correct answer is (c) Both Technician A and Technician B.

3. Technician B is correct. Diesel exhaust oxidation catalysts do store noxious emissions in the substrate when the exhaust temperatures are low. This is known as "cold start emissions," and the stored emissions are later released when the catalyst reaches its operating temperature. Technician A is incorrect in stating that diesel exhaust oxidation catalysts are like the ones used in automobiles for the last 2 decades, as diesel engines have different emissions profiles and require different types of catalysts. Therefore, the correct answer is (b) Technician B.

This entity is responsible for assessing physical security requirements and for conducting critically, vulnerability, and risk assessments:
a. Anti-Terrorism Working Group (ATWG)
b. Anti-Terrorism Officer
c. CI Support Personnel
d. Force Protection Working Group (FPWG)
e. Information Systems Security Managers (ISSM)
f. Installation Commander/Facility Director
g. Law Enforcement Officials
h. Legal Officers
i. Operations Security Officer
j. Physical Security Officer/Provost Marshal
k. Threat Working Group (TWG)

Answers

The Physical Security Officer/Provost Marshal is responsible for assessing physical security requirements and conducting criticality, vulnerability, and risk assessments in relation to anti-terrorism, personnel, and operations.

The correct answer is j. Physical Security Officer/Provost Marshal. This entity is responsible for assessing physical security requirements and for conducting critical, vulnerability, and risk assessments. They work closely with the Anti-Terrorism Officer, Operations Security Officer, and other personnel to ensure the safety and security of the installation or facility. The Anti-Terrorism Working Group (ATWG), Force Protection Working Group (FPWG), and Threat Working Group (TWG) may also be involved in assessing and mitigating risks related to terrorism or other threats. Legal Officers and Information Systems Security Managers (ISSM) may provide guidance and support but are not typically involved in conducting vulnerability assessments or physical security planning.


Learn more about Operation:

brainly.com/question/30581198

#SPJ11

True or False
An enterprise data model is created only for documentation, but is otherwise inconsequential.

Answers

False.

An enterprise data model is not only created for documentation purposes but also for organizing and defining data within an organization. It serves as a blueprint for data integration, data governance, and data management strategies. Therefore, it is not inconsequential, but rather a critical component of an organization's data infrastructure.

To learn more about data model, follow the link:

brainly.com/question/30698183

#SPJ11

False.

An enterprise data model is not created only for documentation.

Enterprise data is a crucial component in understanding and organizing the data structure within an organization, and it aids in the development of effective data management strategies, ensuring consistency, and facilitating communication between different departments.

Learn more about enterprise data: https://brainly.com/question/29524519

#SPJ11

In Class I, Division 2 location where a motor is used, space heaters are used during shutdown periods to __________.
501.130

Answers

Division 2 location where a motor is used, space heaters are used during shutdown periods to prevent condensation and maintain a safe operating temperature within the motor. This helps to protect the motor from potential damage caused by moisture or temperature changes.

The operating temperature of the motor in Fahrenheit is approximately 97°F.

To find the operating temperature of the motor in Fahrenheit, we need to first convert the ambient temperature from Fahrenheit to Celsius, add the self heating temperature in Celsius, and then convert the result back to Fahrenheit. We can use the following formulas to convert between Fahrenheit

The auxiliary electromagnetic unit (APU) is a small gas turbine engine mounted in the tail cone of an aircraft to provide autonomous electrical and mechanical power for the following: Starting power for the main engines.

Learn more about   operating temperature here

https://brainly.com/question/28270063

#SPJ11

5182 - One of the main functions of flaps during the approach and landing is to:-Decrease the angle of descent without increasing the airspeed- Provide the same amount of lift at a slower airspeed- Decrease lift, thus enabling a steeper-than-normal approach to be made

Answers

One of the main functions of flaps during the approach and landing is to provide the same amount of lift at a slower airspeed. This allows for a controlled descent and a steeper angle of approach without increasing the airspeed, ensuring a safe and stable landing.

The main function of flaps during the approach and landing is to provide the same amount of lift at a slower airspeed. By extending the flaps, the wing area and camber are increased, which generates more lift at a lower airspeed. This allows the aircraft to fly at a lower speed without stalling, which is critical during approach and landing when the aircraft needs to descend at a shallow angle without gaining excessive airspeed. Flaps also increase drag, which helps to slow down the aircraft. By increasing drag, the aircraft can maintain a slower airspeed while descending at a steeper angle. However, this is not the primary function of flaps during landing.

Learn more about aircraft here-

https://brainly.com/question/28246952

#SPJ11

Friction course has what PG binders in its makeup?

Answers

"Friction course typically uses PG 64-22 or PG 70-22 binders in its makeup to provide high skid resistance and improved durability."

A friction course, also known as a high friction surface treatment, is a type of pavement surface treatment used to improve the skid resistance of roadways, particularly in wet or slippery conditions. The friction course is composed of a layer of high-quality aggregates, typically granite or quartz, and a polymer-modified asphalt binder that provides excellent adhesion and durability. The polymer-modified binder used in the friction course is often a Performance Grade (PG) binder, which is selected based on its high-temperature performance and resistance to rutting and cracking. PG 64-22 and PG 70-22 binders are commonly used in friction courses due to their high-temperature viscosity, which helps to maintain aggregate embedment and prevent stripping, as well as their low-temperature stiffness, which provides excellent skid resistance in cold weather conditions.

Learn more about friction course here:

https://brainly.com/question/13684931

#SPJ11

The decision-making authority on a job needs to be given to who?

Answers

The decision-making authority should be delegated to the person who is best equipped to make decisions in the best interest of the project, the team, and the organization as a whole.

The decision-making authority on a job should be given to the person who is best qualified to make informed decisions based on their knowledge, skills, and experience. In some cases, this may be the project manager or the supervisor in charge of the work crew. In other cases, it may be a subject matter expert who has specialized knowledge in a particular area. It is important to ensure that the person with decision-making authority has the necessary training, experience, and authority to make informed decisions and to take responsibility for the outcomes of those decisions. Effective communication, collaboration, and leadership skills are also important for anyone in a decision-making role.

Learn more about decision-making authority here:

https://brainly.com/question/23818047

#SPJ11

Which of the following would not be considered physical capital? A. An axe B. Fertile soil C. A factory D. A forklift

Answers

B. Fertile soil would not be considered physical capital.  Physical capital refers to tangible, man-made assets that help in the production process, like tools, machinery, and buildings. Fertile soil, however, is a natural resource and not a man-made asset.


Physical capital refers to tangible assets used in production, such as machinery, tools, equipment, and buildings. These assets are used to create goods and services, and they require an initial investment to acquire.

An axe, a factory, and a forklift are all examples of physical capital because they are tangible assets that are used in production. An axe is a tool that can be used for cutting down trees to make lumber, a factory is a building where goods are manufactured, and a forklift is a machine used to move heavy materials around a factory or warehouse.

Fertile soil, on the other hand, is not a tangible asset that is used in production. While it is certainly important for agriculture and farming, it is not a physical asset that can be used to create goods or services. Instead, it is considered a natural resource that is used in conjunction with physical capital to produce crops and other agricultural products.

Learn more about initial investments here:

brainly.com/question/13540082

#SPJ11

Hi!

The option that would not be considered physical capital is B. Fertile soil.

Physical capital includes items such as an axe (A), a factory (C), and a forklift (D), which are tangible assets used in the production of goods and services. Fertile soil, on the other hand, is considered a natural resource rather than physical capital.

Learn more about physical capital: https://brainly.com/question/13568995

#SPJ11

What is the purpose of the coupling agent in ultrasonic testing? a) to transmit an electrical signal between the detector and sample. b) to transmit and act as a medium for ultrasonic waves. c) to transmit and act as a filter for ultrasonic waves. d) to filter an electrical signal between the detector and sample

Answers

The purpose of the coupling agent in ultrasonic testing is to transmit and act as a medium for ultrasonic waves. Therefore, the correct answer is (b).

State the purpose of the coupling agent in ultrasonic testing.

Ultrasonic testing (UT) is a non-destructive testing method that uses high-frequency sound waves to detect and characterize flaws or defects in materials. In UT, a transducer generates sound waves that travel through the material being tested. When these sound waves encounter a flaw, some of the energy is reflected back to the transducer and detected, allowing for the detection and characterization of the flaw.

However, for the sound waves to travel efficiently from the transducer to the material being tested, a coupling agent is needed. The purpose of the coupling agent is to provide a medium that can transmit the ultrasonic waves from the transducer to the material without significant loss of energy due to reflection or refraction at the air/material interface.

Typically, a liquid is used as a coupling agent in UT, such as water or glycerin. The liquid fills the gap between the transducer and the material being tested, allowing the ultrasonic waves to pass through the liquid and into the material. The liquid also helps to eliminate any air pockets that may exist between the transducer and the material, which can interfere with the transmission of the ultrasonic waves.

The purpose of the coupling agent in ultrasonic testing is to transmit and act as a medium for ultrasonic waves. Therefore, the correct answer is (b).

Learn more about Ultrasonic testing

brainly.com/question/17296114

#SPJ11

the class shirt extends the clothing class. to make the class dressshirt inherit the functionality of both clothing and shirt its class header would be:
Group of answer choices
public class DressShirt inherits Shirt, Clothing
public class DressShirt inherits Shirt
public class DressShirt extends Shirt
public class DressShirt extends Shirt, Clothing
If Shirt inherits Clothing, then Shirt has direct access to the ______ members of Clothing
Group of answer choices
public and protected
public
private
protected
private and protected
Shirt inherits Clothing. What is the first thing that must happen in the Shirt constructor?
Group of answer choices
Initialize the required Shirt fields
Call the Clothing constructor
Create all objects required for Shirt fields
Map the parameters coming into the constructor to Shirt fields

Answers

The correct answer for the first question is: public class DressShirt extends Shirt, Clothing. The correct answer for the second question is: protected members of Clothing.

The correct answer for the third question is: Call the Clothing constructor. To make the class DressShirt inherit the functionality of both Clothing and Shirt, its class header would bethe class shirt extends the clothing class. to make the class dress shirt inherit the functionality of both clothing and shirt its class header would be.

public class DressShirt inherits Shirt, Clothing public class DressShirt inherits Shirt public class DressShirt extends Shirtpublic class DressShirt extends Shirt, Clothing. Your answer: public class DressShirt extends Shirt If Shirt inherits Clothing, then Shirt has direct access to the members of Clothing, Your answer: Call the Clothing constructor.

To know more about DressShirt:- https://brainly.com/question/31491617

#SPJ11

The correct answer to the first question is: public class DressShirt extends Shirt, Clothing constructor.

The correct answer to the second question is: public and protected.

The correct answer to the third question is: Call the Clothing constructor.

Learn more about Clothing constructor: https://brainly.com/question/13267121

#SPJ11

Question 76
A joist is used:
a. To hold up a floor
b. As a horizontal support
c. As a roof only support
d. As a support for sheet rock

Answers

A joist is a structural element typically made of wood, steel, or other materials that is used to provide support in building construction. Joists are commonly used in framing to hold up a floor or to provide horizontal support in walls, roofs, and ceilings. They are usually spaced apart and run parallel to each other, forming the framework that supports the load of the structure above. Joists are an essential component in the construction of buildings, providing stability and structural integrity.

In some cases, joists may also be used as a support for sheetrock or other finishes, but their primary purpose is to provide support for floors and horizontal elements in construction. A joist is a horizontal structural member that runs parallel to the ground and is used to support a floor or ceiling. It can also be used as a horizontal support for other structures, such as decks or balconies, but it is not typically used as a roof-only support. Additionally, while a joist can provide support for sheetrock, this is not its primary function.

learn more about Joist here:

https://brainly.com/question/29999823

#SPJ11

5202 - On a wing, the force of lift acts perpendicular to the relative wind and the force of drag acts parallel to the:- chord line-flightpath-longitudinal axis

Answers

On a wing, the force of lift acts perpendicular to the relative wind and the force of drag acts parallel to the flightpath. Option b is answer.

The chord line is an imaginary straight line that connects the leading edge to the trailing edge of the wing and the longitudinal axis is an imaginary line that runs through the center of the airplane from nose to tail. The force of lift is generated due to the difference in air pressure on the top and bottom surfaces of the wing, and it acts perpendicular to the relative wind, which is the direction of the airflow relative to the wing.

The force of drag, on the other hand, is generated due to the resistance of the air to the motion of the airplane through it, and it acts parallel to the flightpath of the airplane.

Option b is answer.

You can learn more about flightpath at

https://brainly.com/question/29119301

#SPJ11

Refer to the exhibit. A TCP segment from a server has been captured by Wireshark, which is running on a host. What acknowledgement number will the host return for the TCP segment that has been received?

Answers

The acknowledgement number should be equal to the Sequence Number of the received TCP segment plus the Length of the data in the segment.
The acknowledgement number that the host will return for the received TCP segment can be determined by analyzing the Wireshark capture. In this case, the acknowledgement number should be equal to the Sequence Number of the received TCP segment plus the Length of the data in the segment (if any).
For example, if the captured TCP segment has a Sequence Number of 1000 and carries 500 bytes of data, the host would return an acknowledgement number of 1500 (1000 + 500) to confirm the receipt of the segment and request the next expected byte.

Learn more about TCP segment here

https://brainly.com/question/28119964

#SPJ11

The power dissipated in a 4-ohm resistor carrying 3 a is.

Answers

The power dissipated in the 4-ohm resistor carrying 3 amps is 36 watts.

The power dissipated in a resistor is the amount of energy being converted into heat. In this case, we have a 4-ohm resistor carrying a current of 3 amps. Using the formula P=I²R, where P is power, I is current, and R is resistance, we can calculate the power dissipated in the resistor.

Plugging in the given values, we get P=(3A)² x 4Ω = 36W.

It is important to note that power dissipation in a resistor is directly proportional to the current flowing through it and the resistance of the resistor. This means that as the current increases, the power dissipated in the resistor also increases, and vice versa. Additionally, the higher the resistance, the higher the power dissipation.

Therefore, it is important to choose a resistor with an appropriate power rating to avoid overheating and potential damage to the circuit.

You can learn more about resistors at: brainly.com/question/24297401

#SPJ11

Einstein's general theory of relativity predicts that two orbiting neutron stars should radiate gravitational waves. How does the fact that the orbital period is getting shorter support this prediction?

Answers

The observed orbital decay provides strong support for the prediction that neutron star binaries radiate gravitational waves, as predicted by general relativity.

Einstein's general theory of relativity predicts that two orbiting neutron stars should radiate gravitational waves because the orbits should slowly lose energy in the form of these waves, causing the two stars to gradually spiral closer together. As the neutron stars move closer together, their orbital period should decrease. This is because the gravitational force between the two stars is proportional to the inverse square of the distance between them, so as they get closer, the force becomes stronger and they move faster. Observations of neutron star binaries have indeed shown that their orbital periods are decreasing over time, in a manner consistent with the predictions of general relativity. This decrease in orbital period is known as "orbital decay" and it has been measured very precisely using techniques such as pulsar timing.

Learn more about gravitational waves here:

https://brainly.com/question/29607077

#SPJ11

How does a Layer 3 switch differ from a Layer 2 switch?

Answers

A Layer 3 switch differs from a Layer 2 switch in that it has the capability to not only forward traffic based on MAC addresses (like a Layer 2 switch), but also based on IP addresses (like a router).

This means that a Layer 3 switch can make routing decisions and can route traffic between different subnets. In contrast, a Layer 2 switch only forwards traffic based on MAC addresses and does not have the ability to route traffic between different networks.

Essentially, a Layer 3 switch combines the functionalities of a Layer 2 switch and a router into one device.
A Layer 3 switch differs from a Layer 2 switch in terms of the networking layers they operate on and the functionalities they provide.

1. Layer 3 switches operate at the Network Layer (Layer 3) of the OSI model, while Layer 2 switches operate at the Data Link Layer (Layer 2).
2. Layer 3 switches are capable of routing data packets between different networks or subnets, whereas Layer 2 switches can only forward data packets within the same network.
3. Layer 3 switches make forwarding decisions based on IP addresses, while Layer 2 switches use MAC addresses for forwarding data frames.

In summary, Layer 3 switches have more advanced capabilities, allowing them to handle both switching and routing tasks, while Layer 2 switches are limited to local network switching.

Learn more about traffic at : brainly.com/question/8513932

#SPJ11

TFFN can be described as stranded fixture wire with thermoplastic insulation, nylon cover. (True/False)

Answers

True, TFFN can be described as stranded fixture wire with thermoplastic insulation and a nylon cover.

 

A thermoplastic is a class of polymer that can be softened through heating and then processed using methods such as extrusion, injection moulding, thermoforming and blow moulding.

Thermoplastics harden once cooled and do not show any changes in chemical property after being heated and cooled multiple times, making them easily recyclable.

Amorphous and Semi-crystalline Thermoplastics

Thermoplastics are made by joining small molecules, called monomers, together to form long chains using a process called polymerisation. A single polymer chain can be made from many thousands of monomers. The atoms in a polymer chain are joined by strong covalent bonds, whereas the forces between chains are weak.

Depending on the type of monomer, polymer chains may have side branches. If a polymer chain has only a few, short side branches then the chains can form ordered, crystalline regions, called spherulites. However, if the chain has many large side branches, then it is not possible for ordered regions to be formed and the polymer is amorphous.

learn more about  thermoplastic here:

https://brainly.com/question/29596428

#SPJ11

How do IO device utilization and CPU utilization conflict?

Answers

IO device utilization and CPU utilization conflict because they both demand system resources.


When a system is heavily utilizing IO devices, it can cause a bottleneck in the system, as the CPU may have to wait for the IO devices to complete their operations before it can continue processing instructions. This can result in a decrease in CPU utilization, as the CPU is idle while waiting for IO operations to complete.
On the other hand, when the CPU is heavily utilized, it can cause a bottleneck in the system, as IO devices may have to wait for the CPU to process instructions before they can start processing data. This can result in a decrease in IO device utilization, as the IO devices are idle while waiting for the CPU to finish processing.
To optimize system performance, it is important to balance IO device utilization and CPU utilization, ensuring that neither resource is overly burdened and that data processing is efficiently distributed between the CPU and IO devices.
When IO devices (such as keyboards, mice, or storage devices) are used extensively, they consume system resources like memory and processing time. This can lead to reduced CPU utilization, as the CPU must devote time to manage IO operations instead of focusing on executing other tasks. Consequently, a balance between IO device utilization and CPU utilization is essential for optimal system performance.IO device utilization refers to the amount of time an IO device, such as a hard drive or network adapter, is actively processing data. CPU utilization refers to the amount of time the CPU is actively processing instructions.

To know more about IO devices, click here:

https://brainly.com/question/3668486

#SPJ11

making data look like it has come from a different source is called __________.

Answers

"Making data look like it has come from a different source is called"

Hi! Making data look like it has come from a different source is called data spoofing.

Learn more about different source: https://brainly.com/question/896456

#SPJ11

A host is accessing an FTP server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.)

Answers

When a host is accessing an FTP server on a remote network, intermediary network devices perform the following three functions: Routing, Address Resolution, Packet Forwarding.



ICMP is a control and information protocol used by network devices to determine such things as a remote network's availability and the length of time required to reach a remote network.

1. Routing: Intermediary devices, such as routers, determine the best path for data packets to travel between the host and the remote FTP server, ensuring efficient and reliable communication.
2. Address Resolution: Devices like switches and routers use the Address Resolution Protocol (ARP) to resolve IP addresses to their corresponding MAC addresses, enabling data transfer between hosts and network devices.
3. Packet Forwarding: Network devices, such as switches and routers, forward data packets to their appropriate destinations based on their MAC and IP addresses, facilitating communication between the host and remote FTP server.

Learn more about remote network here

https://brainly.com/question/29896632

#SPJ11

Receptale outlets in floors shall not be counted as part of the required number of receptacle outlet unless located within ______ inches of the wall.
210.52(4)

Answers

Floor receptacles are not counted as part of the receptacle count unless they are within 18 inches of a wall as described in National Electrical Code Section 210.52(4).

According to National Electrical Code (NEC) 210.52(A)(4), floor equipment should not be counted as part of the equipment requirement unless it is 18 inches from the wall. National Electrical Code (NEC), or NFPA 70, is the United States standard for the safety of electrical installations and equipment.

It is part of the National Fire Code Series published by the National Fire Protection Association (NFPA), a private trade association. Although the word "state" is used, it is not a federal law. It is often adopted by states and municipalities to regulate electrical safety. In some cases, NECs may be modified, modified and revoked by local authorities elected by local leaders.

Learn more about Code:

brainly.com/question/17204194

#SPJ11

a tsunami watch is issued by the pacific tsunami warning center when __________.

Answers

A tsunami watch is issued by the Pacific Tsunami Warning Center when a large earthquake occurs in the Pacific Ocean that has the potential to generate a tsunami. They detect an earthquake or other event that has the potential to generate a tsunami in the Pacific Ocean.

The watch is issued as a precautionary measure to alert coastal communities to the possibility of a tsunami and to encourage them to prepare for the worst-case scenario. The warning center monitors seismic activity and sea level readings to determine the likelihood of a tsunami and will issue a warning if there is a high probability of a tsunami reaching the coastline. It is important to take tsunami watches and warnings seriously and follow evacuation orders to ensure the safety of yourself and others.
The watch is issued to alert affected coastal regions and help them prepare for a possible tsunami, allowing residents and officials to take necessary precautions and monitor the situation closely.

Learn more about seismic activity here:

brainly.com/question/30667043

#SPJ11

A tsunami watch is issued by the Pacific Tsunami Warning Center when there is a possibility of a tsunami occurring in the Pacific Ocean, usually due to an earthquake or other seismic event.

Tsunamis are massive waves that result from seismic activity or volcanic eruptions beneath the ocean. When formed in the open sea, the height of the waves remains relatively constant. However, as the waves approach the shore, they gather momentum and grow taller due to the decreasing depth of the water.

This watch serves as an early warning to coastal areas, allowing them to prepare for a potential tsunami.

Learn more about Tsunamis: https://brainly.com/question/11687903

#SPJ11

Low voltage equipment that is frequently in contact with the bodies of person or has exposed current carrting elements shall operate on an electrical potential of ______ volts or less.
517.64

Answers

Electrical potential refers to the amount of electric charge per unit of electrical potential energy, measured in volts.

Low voltage equipment that is frequently in contact with the bodies of person or has exposed current carrying elements shall operate on an electrical potential of 30 volts or less.

This is because low voltage is typically defined as 50 volts or less, but for safety reasons, it is recommended to use 30 volts or less for equipment that is in contact with the human body.

According to the Low Voltage Directive (Directive 2014/35/EU), which applies to electrical equipment operating in the European Union, the voltage limits for low voltage equipment are between 50V and 1000V for AC and 75V and 1500V for DC1. The voltage limits relate to the voltage of the electrical input or output, not to voltages generated within the equipmen

Learn more on Voltage : brainly.com/question/31493810

#SPJ11

5225 - As the angle of bank is increased, the vertical component of lift:- decreases and the horizontal component of lift increases- increases and the horizontal component of lift decreases-decreases and the horizontal component of lift remains constant

Answers

As the angle of bank is increased, the vertical component of lift decreases while the horizontal component of lift increases.

This is due to the fact that the lift generated by the wings is split into two components: the vertical lift that opposes the force of gravity, and the horizontal lift that allows the aircraft to turn. When the angle of bank is increased, more of the lift is directed horizontally to turn the aircraft, causing a decrease in the vertical lift component. However, the horizontal lift component increases to maintain the overall lift necessary for flight.

To learn more about vertical click the link below:

brainly.com/question/18084516

#SPJ11

(370-3) Cablebus framework, where _____, shall be permitted as the equipment grounding conductor for branch circuits and feeders.

Answers

Cablebus framework, where properly installed and listed, shall be permitted as the equipment grounding conductor for branch circuits and feeders. The number of distinct paths between the nodes is equal to the number of branches present in the given circuit.

The total number of sites where two or more components are linked together constitutes the number of nodes in the given  branch circuit. A resistor is an electrical aspect that limits or regulates the go with the flow of electrical modern-day in a digital circuit. Resistors can also be used to offer a selected voltage for an energetic device together with a transistor.

To explain more on the subject, nodes and branches are crucial elements of an electrical circuit since they are necessary for the circulation of current inside the circuit. The points in a circuit where two or more components are coupled together are represented by nodes, and the possible paths for the current to go between nodes are represented by branches.

Learn more about branch circuits here

https://brainly.com/question/30612455

#SPJ11

The compound beam shown in figure is pin connected at B. Determine the components of reaction at its supports. Neglect its weight and thickness.

Answers

The values based on the information given will be Ra = 1000N and Rc= 90N

What is weight?

Weight refers to the measure of the force of gravity on an object, and is typically measured in units of mass, such as kilograms or pounds. Weight is influenced by the mass of the object and the strength of the gravitational field it is in.

Thickness, on the other hand, refers to the measure of how thick an object is, or the distance between opposite surfaces of an object. Thickness is typically measured in units of length, such as millimeters or inches.

While weight and thickness are not directly related to each other, they can both play important roles in determining the properties and uses of an object. For example, a thin piece of metal may be lightweight, but may not be strong enough to support heavy loads. Conversely, a thicker piece of metal may be heavier, but may be able to support heavier loads due to its increased strength.

Learn more about thickness on

https://brainly.com/question/4937019

#SPJ1

A large, coal-fired electric power plant produces 12 million kilowatt-hours of electricity each day. Assume that an input of 10,000 BTU's of heat is required to produce an output of 1 kilowatt-hour of electricity.

Answers

To generate 12 million kilowatt-hours of electricity daily, the power plant needs a technology which provides an input of 120 billion BTUs of heat (12 million x 10,000).

To produce 12 million kilowatt-hours of electricity per day, the large, coal-fired electric power plant requires 120 billion BTUs of heat each day (12 million kWh/day x 10,000 BTU/kWh = 120 billion BTUs/day).
A large, coal-fired electric power plant produces 12 million kilowatt-hours of electricity each day. To produce 1 kilowatt-hour of electricity, an input of 10,000 BTUs of heat is required. Therefore, to generate 12 million kilowatt-hours of electricity daily, the power plant needs an input of 120 billion BTUs of heat (12 million x 10,000).

To learn more about technology, click here:

brainly.com/question/31238904

#SPJ11

Based on the information provided, we can calculate the total input of heat required to produce the 12 million kilowatt-hours of electricity generated by the power plant each day.

First, we need to convert the units of measurement for the input of heat from BTUs to kilowatt-hours. One kilowatt-hour is equal to 3,412 BTUs (British Thermal Units).

So, 10,000 BTUs is equal to 2.938 kilowatt-hours (10,000 ÷ 3,412).

Next, we can calculate the total input of heat required for the power plant to produce 12 million kilowatt-hours of electricity each day:

12,000,000 kilowatt-hours × 2.938 kilowatt-hours per BTU = 35,256,000,000 BTUs

Therefore, the large, coal-fired electric power plant requires an input of approximately 35.3 billion BTUs of heat each day to produce 12 million kilowatt-hours of electricity.

Learn more about input of heat: https://brainly.com/question/28086341

#SPJ11

Other Questions
Question 66Garbage reduction melts out fats that are used in manufacturing ofa. soaps, glycerines and cosmeticsb. glue and cementc. grouting and calkd. fertilizer and cattle feed your hmmwv handled properly while driving on the highway after driving through muddy terrain you notice that the wheels wobble and shimmy while driving. what is the most likely cause? With xchg, once the lock flag is et to 0, True or false, what happens? A host is accessing a Web server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.) Which plant is the only kingdom that has cell walls, autotrophic and multicellular? Why was John Steinbeck so good at describing the Great Depression in his novels? There are three aspects of organizational functioning that seem to be especially important in determining an MNC's organizational culture. They are: A. the general views that employees hold about the MNC's purpose, destiny, goals, and their places in them; the age of the organization; and the degree of cultural diversity among the members of the organization. B. the general relationship between the managers and the rank-and-file employees in the organization, the degree of cultural diversity among the members of the organization, and the hierarchical system of authority that defines the roles of managers and subordinates.C. the degree of cultural diversity among the members of the organization, the age of the organization, and the strength of the organization's leadership.D. the general relationship between the employees and their organization; the hierarchical system of authority that defines the roles of managers and subordinates; and the general views that employees hold about the MNC's purpose, destiny, goals, and their places in them. What political entity controlled China beginning in 1921? Describe in detail what is industrial smog and examples of places that have industrial smog. show that the boundary of a generalized rectangle is the union of finitely many closed generalized rectangles with volume zero. 01. Resuelve: (4x + 8x +12) + (5x 3x + 6) =02. Evala: 5-21 + (-3) (2) =03. Evala la expresin: (-3) (-2) (-1) (4) =04. 18+ 3x = 27, el valor de x es:05. Evala: 3 + 4 (3) = The discount rate isA. the interest rate the Fed charges to banks for loans from the Fed.B. the interest rate banks charge their best customers.C. the interest rate banks charge each other for overnight loans.D. the interest rate the U.S. Treasury pays on Treasury Bills.Contractionary monetary policy causesA. aggregate demand to fall and the price level to rise.B. aggregate demand to fall and the price level to fall.C. aggregate demand to rise and the price level to rise.D. aggregate demand to rise and the price level to fall.If the federal? government's expenditures are less than its tax? revenues, thenA. a budget surplus results.B. a budget deficit results.C. the budget is balanced.D. No conclusion can be drawn here regarding the budget surplus or deficit without information regarding government purchases versus other outlays.Based on the following information, what is the balance on the current account?Exports of goods and services = $5 billionImports of goods and services= $3 billionNet income on investments = minus $2 billionNet transfers = minus $2 billionIncrease in foreign holdings of assets in the United States = $4 billionIncrease in U.S. holdings of assets in foreign countries? = $1 billionA. minus -$2 billionB. $1 billionC. $3 billionD. $4 billionIf the nominal exchange rate between the American dollar and the Canadian dollar is 0.89 Canadian dollars per American?dollar, how many American dollars are required to buy a product that costs 2.5 Canadian dollars? A bag contains 3 marbles: a blue marble, an orange marble, and a white marble. A marble is chosen twice with replacement. Find the sample space. Which field in an IPv4 packet header will typically stay the same during its transmission? It is evident that the concept of knowledge cannot be observed as____. O being both a thing and a process O having both intrinsic and unconditional value O being dependent upon context O having behaviors and properties that are different from commodities and resources imma be giving brainliest if you help me!!!???!!?? (Q001)Why was the dollar-gold convertibility important?(Q002) Which theoretical approach best explains Nixon's decisionto end convertibility?each question needs 100-150 words Cancer cells: are indistinguishable from normal body cells. have a slower mitotic rate than normal body cells. do not spread into other body tissues. may exhibit metastasis. Which of these factors is NOT a major factor in determining how fast decomposition occurs?Number of detritivores present None of the choices (all are important) Temperature Moisture 1. TrianglesB = 4in, H = 5inB = 6ft, H= 10ftB = 12m, H = 15mApplication: Sandy is making tablecloths in the shape of triangles. She needs to make two triangle tablecloths for one table. The triangles have base of 2 ft and a height of 4 ft. What is the total area of the triangle tablecloths for one table?2. Parallelogram (H = height) and (B = base)H = 9in, B = 6inH = 5 ft, B = 2ftH = 7yds, B = 3ydsApplication: If a parallelogram has a base of 13 mm and an area of 78 mm2 what is the height?Hint: Use the formula. Substitute the given values and then solve as an equation.3. Rectangle (L = length) and (w = width)rect. DKIF with L = 8 ft and w = 6 ftrect. AOPU with L = 13 ft and w = 5 ftApplication: Charles is paining the den. Two walls are 9 ft high and 15 ft long. The other two walls are 8 ft high and 10 ft long. Charles bought one gallon of paint that will cover 440 square feet of wall space. Does he have enough paint? Explain.4. Rhombus ( d1 = diagonal 1) (d2 = diagonal 2)rhombus with d1 = 12 yds and d2 = 12 ydsrhombus with d1 = 10 ft and d2 = 25 ftrhombus with d1 = 16 in and d2 = 22 inApplication: a rhombus as an area of 72 ft and the product of the diagonals is 144. What is the length of each diagonal?5. Trapezoid ( b1 = base 1) (b2 = base 2) (H = height)b1 = 6 ft, b2 = 7 ft, H = 10 ftb1 = 5 yds, b2 = 8 yds, H = 4 ydsc. b1 = 9 in, b2 = 11 in, H = 13 ind. Application: The two bases of a trapezoid = 16 km and its area = 32 km2. What is its height?