Select all the options that correctly describe the speed of light (c).A. X-rays, ultraviolet light, and microwaves all travel at the same speed when in a vacuum.
B. The speed of light, c, is equal to 3.0 x 108 m/s.

Capacitance of capacitors depends on several factors. Here are 3 key requirements that influence capacitance: Surface Area , Distance between Plates , Dielectric Material.

1. Surface Area: Capacitance is directly proportional to the surface area of the capacitor's conductive plates. Larger surface areas allow for more charge to be stored, which increases the capacitance value.
2. Distance between Plates: Capacitance is inversely proportional to the distance between the capacitor's plates. As the distance between the plates decreases, the electric field strength between them increases, leading to a higher capacitance value.
3. Dielectric Material: Capacitance is also dependent on the dielectric material (insulator) placed between the plates. The dielectric constant of the material determines its ability to store electric charge, and a higher dielectric constant results in a higher capacitance value.

learn more about Capacitance Refer: https://brainly.com/question/28445252

#SPJ11

To find the thermal energy generated due to friction, we need to first calculate the potential energy the child had at the top of the slide and compare it to the kinetic energy the child had at the bottom of the slide. The difference between these two energies is the amount of energy lost due to friction.

Potential energy (PE) = mass x gravity x height
PE = 16.0 kg x 9.81 m/s^2 x 2.20 m
PE = 344.11 J

Kinetic energy (KE) = 1/2 x mass x speed^2
KE = 1/2 x 16.0 kg x (1.25 m/s)^2
KE = 12.50 J

The energy lost due to friction is the difference between PE and KE:
Energy lost = PE - KE
Energy lost = 344.11 J - 12.50 J
Energy lost = 331.61 J

Therefore, 331.61 J of thermal energy due to friction was generated in this process.
Hi! To calculate the thermal energy due to friction generated in this process, we'll use the conservation of energy principle. Initially, the child has potential energy which is converted into kinetic energy and thermal energy due to friction as they descend the slide.

1. Calculate the initial potential energy (PE) of the child:
PE = m * g * h
PE = 16.0 kg * 9.81 m/s² * 2.20 m = 346.848 J

2. Calculate the final kinetic energy (KE) of the child at the bottom of the slide:
KE = 0.5 * m * v²
KE = 0.5 * 16.0 kg * (1.25 m/s)² = 12.5 J

3. Determine the thermal energy (TE) generated due to friction:
The initial potential energy is converted into both kinetic energy and thermal energy. So,
TE = PE - KE
TE = 346.848 J - 12.5 J = 334.348 J

Thus, 334.348 Joules of thermal energy due to friction was generated in this process.

To know more about Thermal Energy click here .

brainly.com/question/18989562

#SPJ11

Extraction, transformation, and loading, or ETL for short, is a process used in data warehousing to move data from various sources into a centralized location.

Extraction involves gathering data from sources such as databases, applications, and files. Transformation involves converting the data into a common format and applying any necessary business rules or data cleaning processes. Loading involves inserting the transformed data into a data warehouse or other repository where it can be accessed and analyzed. Overall, ETL is a critical step in the data warehousing process, as it ensures that data is accurate, consistent, and ready for analysis. Extraction involves retrieving data from various sources, transformation refers to converting and cleansing the extracted data into a consistent format, and loading involves importing the transformed data into a target system or database for analysis and use.

To learn more about Extraction click here https://brainly.com/question/16848369

#SPJ11

Article 396 covers the use, installation, and construction specifications for messenger-supported wiring. As per 396.30 A The messenger shall be supported at dead ends and at intermediate locations so as to eliminate tension on the conductors.

The messenger shall be supported at dead ends and at intermediate locations so as to eliminate stress on the conductors. This ensures that the conductors remain in place and do not sag or break, as the messenger serves as a support structure. The intermediate locations refer to the points along the length of the conductor where additional support is needed beyond the dead ends. Conductors are the wires that transmit electrical energy, and they need to be supported properly to prevent damage or failure. The messenger shall be supported at dead ends and at intermediate locations so as to eliminate "strain" on the conductors.

learn more about messenger here

https://brainly.com/question/14366755

#SPJ11

The correct option is d.

As long as necessary to permit the clearing of the service line. The amount of time required for the water to run will vary depending on the length of the service line and the specific characteristics of the distribution system. It is important to allow enough time for the water to flush out any stagnant water and debris that may have accumulated in the service line.
 When collecting a distribution system sample, the water should be allowed to run for a period of time prior to sample collection. This period of time is: Thus, option d. As long as necessary to permit the clearing of the service line

Learn more about the period of time here:- brainly. in/textbook-solutions/q-time-period.

#SPJ11

A wind profiler obtains wind information using a Doppler radar. The correct option is a. A Doppler radar is a type of radar that measures the motion of objects by detecting changes in the frequency of the waves it emits and receives.

When the radar wave hits an object, such as a particle in the atmosphere, the frequency of the wave changes. This change is detected by the radar, which can determine the velocity of the object.

Wind profilers use Doppler radar to measure the velocity of atmospheric particles, such as dust or water droplets, that is carried by the wind.

By measuring the velocity of these particles at different heights above the ground, wind profilers can create a vertical profile of wind speed and direction. This information is important for weather forecasting, aviation, and air quality monitoring.

To know more about Doppler radar refer here:

https://brainly.com/question/5836412#

#SPJ11

Using a Doppler radar, a wind profiler gathers wind data. The right response is a.

Doppler radars are a particular kind of radar that track changes in the frequency of the waves they send and receive to determine the motion of objects.

The frequency of the radar wave changes when it collides with an item, like an atmospheric particle. The radar, which can ascertain the object's velocity, notices this change.

Doppler radar is used by wind profilers to calculate the velocity of airborne particles such as dust or water droplets.

Wind profilers can produce a vertical profile of wind speed and direction by measuring the velocity of these particles at various heights above the ground. Air quality monitoring, aviation, and weather forecasting all rely on this information.

learn more about Doppler radars here:

https://brainly.com/question/5836412

#SPJ11

This is the torque the engine will develop when running at 2400 RPM, given that one-third of the energy goes into heat and other internal energy forms.

Based on the given information, one-third of the energy is lost to heat and other forms of internal energy of the motor, which means two-thirds of the energy is available for the motor output. However, the amount of torque the engine will develop depends on various factors such as the size and design of the motor, the type of fuel used, and the load on the motor. Therefore, without additional information, it is not possible to determine the exact torque the engine will develop at 2400 rpm.
we need to first find the output power of the engine, and then use that to calculate the torque. Here's a step-by-step explanation:
1. Given that one-third of the engine's energy is converted into heat and other forms of internal energy, this means that two-thirds of the energy goes into the motor output.
2. Let's denote the total engine energy as E_total. Then, the motor output energy (E_output) can be calculated as:
E_output = (2/3) * E_total
3. We are given that the motor is running at 2400 RPM (revolutions per minute). To calculate torque, we need to convert this to radians per second (rad/s). We know that:
1 revolution = 2π radians
1 minute = 60 seconds
So, 2400 RPM = 2400 * (2π / 60) rad/s ≈ 251.33 rad/s
4. The power output (P_output) can be related to the torque (T) and the angular velocity (ω) using the following formula:
P_output = T * ω
5. We know the values of P_output (from step 2) and ω (from step 3), so we can now solve for torque (T) using the formula:
T = P_output / ω
Since we don't have a numerical value for E_total, the answer will be in terms of E_total:
T = (2/3 * E_total) / 251.33
This is the torque the engine will develop when running at 2400 RPM, given that one-third of the energy goes into heat and other internal energy forms.

Learn more about energy here

https://brainly.com/question/1932868

#SPJ11

According to the metric system, 1 metric ton (also known as a tonne) = 1,000,000 grams.  In the United States and some other countries, a ton is often used to refer to a unit of weight.

The metric system is a system of measurement used in most of the world that is based on the International System of Units (SI). The SI unit for mass is the kilogram (kg), which is defined as the mass of a specific cylinder of platinum-iridium alloy kept at the International Bureau of Weights and Measures in France.

The metric ton, also known as the tonne, is a unit of bin the metric system that is equal to 1,000 kilograms. This unit is commonly used to measure large masses of objects such as vehicles, cargo, and building materials.

Since 1 kilogram is equal to 1,000 grams, 1 metric ton is equal to 1,000 x 1,000 = 1,000,000 grams. This means that if you have a mass of 1,000,000 grams, you have a mass of 1 metric ton. Similarly, if you have a mass of 2,000,000 grams, you have a mass of 2 metric tons, and so on.

Learn more about metric system: https://brainly.com/question/23183575

#SPJ11

The ideal efficiency of a heat engine operating between a hot reservoir at 2950K and a cold reservoir at 318K is 0.8925 or 89.25%.

The ideal efficiency of a heat engine is given by the Carnot efficiency formula, which depends on the temperature of the hot reservoir and the temperature of the cold reservoir.

In this case, the hot reservoir temperature is 2950K and the cold reservoir temperature is 318K.

The Carnot efficiency formula is:

Efficiency = 1 - (T_cold/T_hot)

where T_cold is the temperature of the cold reservoir and T_hot is the temperature of the hot reservoir.

Plugging in the given temperatures, we get:

Efficiency = 1 - (318/2950)

Simplifying this expression, we get:

Efficiency = 0.8925

Therefore, the ideal efficiency of a heat engine operating between a hot reservoir at 2950K and a cold reservoir at 318K is 0.8925 or 89.25%.

This means that the engine can convert 89.25% of the heat energy it receives from the hot reservoir into useful work, while the remaining 10.75% is rejected to the cold reservoir.

It is important to note that this is the theoretical maximum efficiency of a heat engine, and in reality, no engine can achieve this ideal efficiency due to factors such as friction and heat loss.

However, the Carnot efficiency provides a useful benchmark for evaluating the performance of real-world heat engines.

To know more about ideal efficiency :

https://brainly.com/question/11752408

#SPJ11

The frequency (f) of an oscillating spring is related to the mass (m) of the object attached to the spring and the spring constant (k) by the following equation:

f = (1/2π) * sqrt(k/m)

where π is pi (approximately equal to 3.14159).

To find the mass required for a spring with a spring constant of 2.000 x 10^3 N/m to oscillate 5.0 times per second, we can rearrange this equation to solve for m:

m = k / (4π^2 * f^2)

Substituting in the given values, we get:

m = (2.000 x 10^3 N/m) / (4π^2 * (5.0/s)^2) = 0.0255 kg

Therefore, the mass required for the spring to oscillate 5.0 times per second is 0.0255 kg (or approximately 25.5 grams).

Similarly, to find the mass required for the spring to oscillate 10.0 times per second, we can use the same equation:

m = (2.000 x 10^3 N/m) / (4π^2 * (10.0/s)^2) = 0.00638 kg

Therefore, the mass required for the spring to oscillate 10.0 times per second is 0.00638 kg (or approximately 6.38 grams).

The most penetrating of the given options is gamma rays.

Therefore the answer is c. Gamma rays

When it comes to ionizing radiation, the term "penetration" refers to how deeply the radiation can penetrate into matter before being absorbed. Alpha, beta, and gamma rays are all types of ionizing radiation, but they differ in their ability to penetrate matter.

Alpha rays consist of positively charged particles (helium nuclei) and are relatively large and heavy. As a result, they can be stopped by a sheet of paper or a few centimeters of air, and do not penetrate deeply into matter.

Beta rays consist of fast-moving electrons and can penetrate slightly farther than alpha rays, but can be stopped by a few millimeters of aluminum.

Gamma rays are a form of electromagnetic radiation (like x-rays), and are extremely penetrating. They can pass through thick layers of material, including concrete and steel, and can only be fully stopped by several inches of dense material, such as lead or concrete.

X-rays have similar properties to gamma rays and can also penetrate deeply into matter, but typically have a lower energy and are less penetrating than gamma rays.

To know more on gamma rays

https://brainly.com/question/23281551

#SPJ4

The efficiency of the engine is 20.37%. To calculate the efficiency of the engine, we can use the formula: Efficiency = 1 - (Tc/Th)

Where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir. We know that Th = 964 K and Tc = 622 K.

However, we also know that the engine operates at three-fifths of its maximum efficiency, so we need to take that into account. Let's call the maximum efficiency of the engine Emax. Then, the actual efficiency of the engine can be expressed as:

Efficiency = (3/5) * Emax

Substituting the values we have:

(3/5) * Emax = 1 - (622/964)

Solving for Emax:

Emax = (1 - (622/964)) / (3/5)

Emax = 0.3395

Therefore, the maximum efficiency of the engine is 0.3395.

To find the actual efficiency of the engine, we can substitute this value into the equation we derived earlier:

Efficiency = (3/5) * 0.3395

Efficiency = 0.2037 or 20.37%

So, the efficiency of the engine is 20.37%.

To know more about efficiency, refer

https://brainly.com/question/3617034

#SPJ11

a. True. Almost all sounds contain multiple frequencies because most sounds are a combination of different pitches and tones.

This means that various vibrations occur at different rates, producing a complex sound wave with multiple frequencies.These waves contain different frequencies, amplitudes, and wavelengths that combine to create the sound. Each sound has its own unique spectrum of frequencies, and the combination of these frequencies creates the sound we hear.

Learn more about frequencies Refer: https://brainly.com/question/28466888

#SPJ11

Answer:

Explanation: The hydrostatic pressure at the bottom of tank b will be greater than the hydrostatic pressure at the bottom of tank a. This is because the pressure at the bottom of a fluid is directly proportional to its density and the height of the fluid column above it. Since tank b contains a fluid with a higher density than tank a, it will exert greater pressure at the bottom. Additionally, both tanks are open to the atmosphere, so the atmospheric pressure above both tanks is the same and can be ignored in this comparison. To compare the hydrostatic pressures at the bottom of each tank, we need to consider the following factors: density, height, and the fact that both fluids are static. We'll use the formula for hydrostatic pressure, which is: Hydrostatic Pressure = Density × Gravity × Height For Tank A: Density = rho_a (given rho_a < rho_b) Height = h Gravity = g (constant for both tanks) Hydrostatic Pressure_A = rho_a × g × h For Tank B: Density = rho_b (given rho_b > rho_a) Height = h Gravity = g (constant for both tanks) Hydrostatic Pressure_B = rho_b × g × h Since rho_a < rho_b and both tanks have the same height and gravity, the hydrostatic pressure at the bottom of Tank B will be greater than the hydrostatic pressure at the bottom of Tank A. In summary, Hydrostatic Pressure_A < Hydrostatic Pressure_B.

Learn more about hydrostatic pressure here:- brainly.in/question/153418

#SPJ11

The typical air-fuel mixture by weight during normal engine operation is 14.7:1.

The air-fuel mixture is the ratio of air to fuel in the combustion chamber of an engine. The stoichiometric ratio, or the ideal ratio for complete combustion, is 14.7 parts of air to 1 part of fuel by weight. This means that for every 14.7 units of air, 1 unit of fuel is needed for complete combustion. This ratio is also known as the "lambda" value, and it is used to tune the engine for optimal performance and fuel efficiency.

If the air-fuel ratio is too rich, meaning there is too much fuel compared to air, the engine will produce more power but will burn more fuel and emit more pollutants. If the air-fuel ratio is too lean, meaning there is too much air compared to fuel, the engine will have less power and may even misfire or stall.

To know more on air-fuel mixture

https://brainly.com/question/29534465

#SPJ4

the intensity of the electromagnetic wave with a peak electric field strength of 155 V/m is approximately 1.328 W/m².

The intensity of an electromagnetic wave is proportional to the square of its electric field strength. Therefore, to calculate the intensity (I), we can use the following formula:
I = (electric field strength)^2 / 377
where 377 is the impedance of free space.
Substituting the given value of peak electric field strength (155 v/m), we get:
I = (155)^2 / 377
I = 63.3 w/m2
Therefore, the intensity of the electromagnetic wave with a peak electric field strength of 155 v/m is 63.3 w/m2. calculate the intensity of an electromagnetic wave. To find the intensity (in W/m²) of an electromagnetic wave with a peak electric field strength (E) of 155 V/m, you can use the following formula:
Intensity (I) = (1/2) × ε₀ × c × E²
Here,
ε₀ = vacuum permittivity = 8.854 × 10⁻¹² F/m
c = speed of light in vacuum = 3 × 10⁸ m/s
E = peak electric field strength = 155 V/m
Now, let's plug in the values and calculate the intensity:
I = (1/2) × (8.854 × 10⁻¹² F/m) × (3 × 10⁸ m/s) × (155 V/m)²
I = (1/2) × (8.854 × 10⁻¹² F/m) × (3 × 10⁸ m/s) × (24025 V²/m²)
I = 0.5 × (8.854 × 10⁻¹² F/m) × (3 × 10⁸ m/s) × (24025 V²/m²)
I ≈ 0.5 × 2.656 × 10⁻³ W/m²
I ≈ 1.328 W/m²
So, the intensity of the electromagnetic wave with a peak electric field strength of 155 V/m is approximately 1.328 W/m².

Learn more about electromagnetic here

https://brainly.com/question/17057080

#SPJ11

Adiabatic processes are most important for air that is rising or sinking. This is because adiabatic cooling or warming occurs when air parcels change altitude without exchanging heat with their surroundings.

Adiabatic processes are primarily important for air that is saturated and rising or sinking. When air rises, it expands and cools, causing water vapor to condense and form clouds. This is known as adiabatic cooling. Conversely, when sinking air warms and compresses, it can cause cloud dissipation through adiabatic heating. Adiabatic processes are less significant for polluted or stagnant air masses that remain near the earth's surface because they lack the vertical movement necessary to facilitate adiabatic cooling or heating.

Learn more about Adiabatic processes here:

brainly.com/question/2501376

#SPJ11

To comply with the requirements of Section 110-14(c)(1), the minimum size THHN conductor permitted to terminate on a 70 ampere circuit breaker or fuse is a 4 AWG conductor. This ensures proper terminal ratings and a safe electrical connection.

According to the requirements of Section 110-14(c)(1), the minimum size THHN conductor that is permitted to terminate on a 70 ampere circuit breaker or fuse is #6 AWG copper or #4 AWG aluminum. This is based on the 60-degree Celsius ampacity rating of THHN conductors, which is 65 amperes. However, since the next standard size up from #6 AWG copper or #4 AWG aluminum is #4 AWG copper or #2 AWG aluminum, it is recommended to use those sizes instead to allow for some additional capacity and flexibility in the circuit.

To know more about THHN conductor click here:

https://brainly.com/question/31566503

#SPJ11

It will take approximately 7.29 minutes to add 15,000 gallons to the storage tank with a pump that will deliver 275 gpm.

To solve this problem, we can use the formula:

time = amount of liquid ÷ flow rate

First, we need to convert 15,000 gallons to cubic feet:

15,000 gallons = 15,000/7.481 = 2,004.8 cubic feet

Then, we can plug in the values:

time = 2,004.8 cubic feet ÷ 275 gallons per minute

time = 7.29 minutes

Therefore, it will take approximately 7.29 minutes to add 15,000 gallons to the storage tank with a pump that will deliver 275 gpm.

Learn more about amount of liquid

https://brainly.com/question/24972177

#SPJ4

Warm and low-density water rises to the ocean surface.

Convection is the movement of a liquid or gas that allows thermal energy to be transferred.

Through the mechanism of convection, thermal energy can also travel within the ocean and the atmosphere.

In order to produce temperature differences, convection relies on regions of a liquid or gas heating up or cooling down faster than those around them. Then, as a result of these temperature differences, the areas migrate as the hotter, less dense areas rise and the cooler, denser, sink.

To learn more about convection, click:

https://brainly.com/question/16635311

#SPJ1

The correct answer is (d) 24 hours, as it is the closest option to the calculated detention time.

The proper detention time for disinfecting a water storage tank depends on the initial concentration of the disinfectant, the type of disinfectant used, and the desired concentration of residual disinfectant after the detention time.

In this case, the storage tank is already filled with chlorinated water, and the desired concentration of free chlorine residual after the detention time is 10 mg/L. The proper detention time can be calculated using the following formula:

Detention time = (ln (C2/C1))/k

where C1 is the initial concentration of the disinfectant (in this case, the free chlorine residual in the storage tank), C2 is the desired concentration of residual disinfectant (10 mg/L), and k is the disinfectant decay rate constant.

The decay rate constant for free chlorine in water depends on several factors, including temperature, pH, and the presence of other chemical compounds in the water. For typical drinking water conditions, the decay rate constant for free chlorine is in the range of 0.1-0.5 per hour.

Assuming a conservative value of k = 0.1 per hour, the proper detention time can be calculated as follows:

Detention time = (ln (10/1))/0.1 = 23.0 hours

To know more about decay rate constant

brainly.com/question/30068164

#SPJ11

there must be a one-to-one correspondence between the frequency and intensity of the sound wave for a pure tone to be produced.

b. frequency and intensity.
For a pure tone to be produced, the sound wave must have a single frequency. The intensity of the sound wave determines the loudness of the tone.

For a pure tone (single frequency) to be produced, there must be a one-to-one correspondence between:
d. pressure and pitch.

To know more about Correspondence click here.

brainly.com/question/1597341

#SPJ11

Operators must have unobstructed access to a ladder for escape from a trench within a distance of 25 feet.
According to OSHA regulations, operators must have unobstructed access to a ladder for escape from a trench within 25 feet. So, the correct answer is c 25 feet.

According to OSHA Occupational Safety and Health Administration, employers must provide ladders, steps, ramps, or other safe means of egress for workers working in trench excavations 4 feet 1.22 meters or deeper1. The means of egress must be located so as not to require workers to travel more than 25 feet 7.62 meters laterally within the trench1. Therefore, the answer is c 25 feet. Operators must have unobstructed access to a ladder for escape from a trench within 25 feet. So, the correct answer is c 25 feet

learn more about unobstructed here

https://brainly.com/question/4335923

#SPJ11

The most commonly used meter on small domestic services is the d.nutating disc meter.

This type of meter is typically used in residential and small commercial applications to measure the flow of water, gas, or other liquids. The nutating disc meter works by using a disc that rotates within the flow of the liquid being measured. As the disc rotates, it creates a measurable flow that can be used to determine the amount of liquid passing through the meter. One of the reasons why the nutating disc meter is so commonly used is because of its accuracy. These meters are typically very precise and can measure small amounts of liquid with great accuracy. This is especially important in residential applications where water usage is often measured in small increments.

Another advantage of the nutating disc meter is its durability. These meters are typically made from high-quality materials that are designed to withstand years of use without breaking down or wearing out. This is important in residential applications where meters may be exposed to a wide range of environmental factors, such as temperature fluctuations, exposure to sunlight, and other elements. Therefore, the correct answer is option d.

know more about nutating disc meter here:

https://brainly.com/question/31568597

#SPJ11

The change in the system's kinetic energy of the 950-kg satellite orbiting the earth at a constant altitude of 90 km is zero.

This is because the satellite is orbiting at a constant altitude, meaning its distance from the Earth's center is constant, and therefore, its potential energy remains constant.  When the altitude is constant, there is no change in the system's kinetic energy, as the satellite maintains the same speed and distance from the Earth. Therefore, the change in kinetic energy is 0. Since the total energy of a satellite in orbit is constant, any change in potential energy is compensated by an equal and opposite change in kinetic energy. Therefore, since the potential energy is constant, the kinetic energy must also be constant.

Learn more about orbit  here: https://brainly.com/question/18914648

#SPJ11

Signs of clinical deterioration that would prompt the activation of a rapid response system include symptomatic hypertension, seizure, and unexplained agitation. These conditions can indicate a worsening medical state and necessitate immediate attention and intervention by healthcare professionals.

The signs of clinical deterioration that would prompt the activation of rapid response system include: seizure, unexplained agitation, and symptomatic hypertension. In addition, if the diastolic blood pressure is greater than 60 mm Hg or less than 100 mm Hg, this could also be an indication of clinical deterioration and warrant activation of the rapid response system. It is important to monitor patients closely and be aware of any changes in their condition to ensure timely intervention and prevent further deterioration.

Learn more about  rapid response system here:

https://brainly.com/question/26478305

#SPJ11

Answer:

Explanation:

The melting point and boiling point of a steel pot can vary depending on the specific type of steel and its composition. However, the melting point of most common types of steel used in pots and pans ranges from 1370°C to 1530°C (2500°F to 2790°F).

It is important to note that the boiling point of steel is much higher than its melting point, and it is not practical to heat a steel pot to its boiling point as it would require extremely high temperatures and could result in damage or deformation of the pot.

It is in the process of melting into water. Some of the water will be liquid and some will be solid. The temperature of the water will not change while it’s in B.

A heating curve is a graphical representation of the change in temperature of a substance as heat is added to it. It shows how the temperature of a substance changes as it is heated at a constant rate. The heating curve consists of a horizontal line for each phase change, where the temperature remains constant, and a sloped line for each temperature increase during a phase.

The curve is typically plotted with temperature on the y-axis and the amount of heat added on the x-axis. Heating curves are useful for understanding the behavior of substances as they change from one state to another and can be used to calculate the amount of heat required to cause a phase change or to raise the temperature of a substance to a specific point.

Learn more about heating curve:https://brainly.com/question/27018999

#SPJ1

A storm sewer is used to remove rain and other standing surface water. It is not designed to handle household wastewater or sewage.

The wastewater from households is typically treated at a wastewater treatment plant before being discharged back into the environment. Storm sewers are designed to prevent flooding by carrying excess rainwater away from homes and streets. Gutter drain water may also be directed into the storm sewer system to prevent flooding and water damage.

 A storm sewer is used to remove rain and other standing surface water. So, the correct answer is option a.

To know more about Surface click here .

brainly.com/question/28267043

#SPJ11