According to Article 324 of the National Electrical Code (NEC), receptacles, receptacle housings, and self-contained devices used with flat conductor cable systems shall be listed for the purpose and installed in accordance with their listing and the manufacturer's installation instructions.
This means that these devices should be approved and tested by a recognized testing agency to ensure they meet certain safety standards.
Additionally, they should be installed according to the manufacturer's instructions to ensure proper functioning and prevent any hazards.
It is important to note that the NEC does not specify a particular listing or standard for these devices, leaving it up to the manufacturer to determine the appropriate listing and installation requirements.
For more such questions on National Electrical Code, click on:
https://brainly.com/question/14601815
#SPJ11
A light woman and a heavy man jump from an airplane at the same time and immediately open their same-size parachutes. Which person will reach a state of zero acceleration (terminal velocity) first?
Both the light woman and the heavy man will eventually reach the same terminal velocity, which is the maximum speed that an object can achieve while falling through the air.
This is because terminal velocity is determined by the air resistance that the object experiences, which depends on its size, shape, and speed. However, the heavier man will initially fall faster than the lighter woman due to the force of gravity being stronger on him. As they continue to fall, the air resistance will increase until it matches the force of gravity, at which point they will reach terminal velocity. The heavy man will reach terminal velocity first because his greater mass causes a higher gravitational force acting on him, which in turn leads to a faster acceleration until he reaches terminal velocity. The light woman will experience a smaller gravitational force and will take longer to reach terminal velocity. Therefore, the heavy man will reach zero acceleration (terminal velocity) first, but the light woman will catch up and eventually reach the same speed.
Learn more about resistance here: https://brainly.com/question/30799966
#SPJ11
(Table 300-5) UF cable is used to supply power to a 120 volt 15 ampere GFCI protected circuit. If the cable is installed outdoors under the driveway of a one-family dwelling, the minimum cover requirement is _____ inches.
The minimum cover requirement for UF cable installed outdoors under the driveway of a one-family dwelling to supply power to a 120 volt 15 ampere GFCI protected circuit is 24 inches according to Table 300-5.
This ensures that the cable is adequately protected from damage and potential hazards.
The minimum cover requirement for UF cable. For a UF cable used to supply power to a 120 volt 15 ampere GFCI protected circuit, when installed outdoors under the driveway of a one-family dwelling, the minimum cover requirement according to Table 300-5 is 24 inches.
The minimum cover requirement for UF cable supplying power to a 120 volt 15 ampere GFCI protected circuit, when installed outdoors under the driveway of a one-family dwelling, is 24 inches.
Visit here to learn more about GFCI protected circuit:
brainly.com/question/30239193
#SPJ11
A drop in blood pH is likely to cause a slower breathing rate. True or false.
A drop in blood pH is likely to cause a faster breathing rate. This statement is false.
An increase, not a decrease, in blood pH leads to a slower breathing rate. This is due to the fact that an increase in blood pH, also known as alkalosis, causes a decrease in the concentration of carbon dioxide (CO2) in the blood. This decrease in CO2 causes the respiratory centre in the brain to decrease the rate and depth of breathing, which helps to retain more CO2 in the body and return the blood pH towards normal.
Conversely, a decrease in blood pH, also known as acidosis, leads to an increase in the respiratory rate and depth in order to eliminate excess CO2 from the body, which helps to raise the blood pH towards normal.
To learn more about breathing rate, refer:-
https://brainly.com/question/28835350
#SPJ11
False. A drop in blood pH is more likely to cause a faster breathing rate, not a slower one.
This response is known as respiratory compensation and is one of the body's ways of restoring the acid-base balance.
The acid-base balance of the body is tightly regulated to ensure that pH levels remain within a narrow range.
When there is a drop in blood pH (i.e., an increase in blood acidity), it is typically due to an excess of carbon dioxide (CO2) in the bloodstream.
This excess CO2 combines with water to form carbonic acid, which dissociates into hydrogen ions (H+) and bicarbonate ions (HCO3-). The resulting increase in H+ ions leads to a drop in pH.
To counteract this decrease in pH, the body triggers respiratory compensation.
The respiratory center in the brainstem detects the increase in H+ ions and stimulates the respiratory muscles to increase breathing rate and depth.
This increased ventilation helps to remove excess CO2 from the body, which in turn reduces the amount of carbonic acid and H+ ions in the blood. As a result, the pH level of the blood returns to normal.
Conversely, an increase in blood pH (i.e., a decrease in blood acidity) can lead to a decrease in breathing rate, as there is less stimulation of the respiratory center.
This response is known as hypoventilation and is also a way for the body to regulate pH levels.
To know more about hypoventilation visit link :
https://brainly.com/question/31475439
#SPJ11
in an amusement park water slide, people slide down an essentially frictionless tube. the top of the slide is 3.1 m above the bottom where they exit the slide, moving horizontally, 1.4 m above a swimming pool. does the mass of the person make any difference?
The mass of the person does not make any difference in this scenario, as it does not affect the final velocity of the person sliding down or the horizontal distance traveled after exiting the slide.
1. First, let's address the height difference between the top of the slide and the bottom. The vertical distance is 3.1 meters. This represents the initial potential energy of the person, given by the formula PE = m * g * h, where m is the mass, g is the acceleration due to gravity (approximately 9.81 m/s²), and h is the height (3.1 m).
2. As the person slides down, the potential energy converts into kinetic energy. At the bottom of the slide, the person has lost all their potential energy, and it has been converted into kinetic energy, which can be represented as KE = 0.5 * m * v², where m is the mass and v is the final velocity.
3. Since energy is conserved, we can equate potential and kinetic energy: m * g * h = 0.5 * m * v².
4. You'll notice that both sides of the equation have the mass (m) term, so we can simplify by dividing both sides by m: g * h = 0.5 * v².
5. From this simplified equation, we can see that mass doesn't affect the final velocity of the person sliding down, as it is not present in the equation.
6. As the person exits the slide horizontally 1.4 m above the pool, they will follow a parabolic trajectory due to gravity. However, the mass will not affect their horizontal distance traveled, as it does not influence the horizontal velocity.
So, the mass of the person does not make any difference in this scenario, as it does not affect the final velocity of the person sliding down or the horizontal distance traveled after exiting the slide.
To know more about mass, refer
https://brainly.com/question/86444
#SPJ11
A beam of white light is incident on a thick glass plate with parallel sides, at an angle between 0°and 90° with the normal. Which color emerges from the other side first?A) redB) violetC) greenD) None of the given; all colors emerge at the same time.
The correct answer to the question is D) None of the given; all colors emerge at the same time when the beam of white light is incident on a thick glass plate with parallel sides at an angle of 0° with the normal.
When white light enters a thick glass plate, it undergoes refraction, which means the light waves change direction and speed as they move through the glass. This causes the different colors of the spectrum to separate, with red being the least refracted and violet being the most refracted.
The angle at which the light enters the glass plate determines how much it is refracted, with greater angles causing more refraction. As a result, the color that emerges first from the other side of the glass plate will depend on the angle of incidence.
At an angle of 0°, the light will not be refracted at all and all colors will emerge at the same time. As the angle increases, the colors will start to separate and the order in which they emerge will be: red, orange, yellow, green, blue, indigo, and violet.
To know more about beam refer here:
https://brainly.com/question/31324896#
#SPJ11
The answer is B) violet. When white light enters a thick glass plate at an angle, it undergoes refraction and separates into its constituent colors. This is because different colors have different violets and Wavelength therefore bend at different angles. The color with the shortest wavelength, which is violet, bends the most and emerges first from the other side of the glass plate.
B) violet
When a beam of white light is incident on a thick glass plate at an angle between 0° and 90° with the normal, the light is refracted, and colors separate due to dispersion. Violet light has the shortest wavelength and is refracted more than the other colors, causing it to emerge from the other side of the glass first.
Learn more about violet here;
https://brainly.com/question/11879525
#SPJ11
A box with a mass of 10 kg is packed on an inclined plane that makes a 60 degree angle with the horizontal. The coefficient of static friction between the box and the inclined plane is (.2). What force must be applied on the box in order to prevent the box from sliding down the inclined plane?
To solve this problem, we need to consider the forces acting on the box.The force of friction is equal to the coefficient of static friction multiplied by the normal force, which is 0.2 x 49.05 N = 9.81 N.
There are two forces at play here: the force of gravity acting vertically downwards (which can be calculated using the mass of the box, which is 10 kg and the acceleration due to gravity, which is 9.81 m/s^2) and the force of friction acting horizontally in the opposite direction to the force applied on the box.
The force of friction can be calculated using the coefficient of static friction (.2) and the normal force acting on the box (which is equal to the force of gravity acting perpendicular to the inclined plane, which can be calculated using trigonometry since we know the angle of inclination). The normal force is equal to the force of gravity multiplied by the cosine of the angle of inclination, which is cos(60) = 0.5. Therefore, the normal force is 10 kg x 9.81 m/s^2 x 0.5 = 49.05 N.
To prevent the box from sliding down the inclined plane, the force applied on the box must be greater than or equal to the force of friction. We can use trigonometry again to calculate the force required to keep the box stationary. The force required is equal to the force of gravity acting parallel to the inclined plane, which is equal to the force of gravity multiplied by the sine of the angle of inclination, which is sin(60) = 0.866. Therefore, the force required is 10 kg x 9.81 m/s^2 x 0.866 = 84.77 N.
Therefore, the force that must be applied on the box in order to prevent it from sliding down the inclined plane is 84.77 N.
To prevent the 10 kg box from sliding down the 60-degree inclined plane, you need to balance the component of gravitational force acting along the incline and the force due to static friction. The component of gravitational force acting along the incline can be calculated using:
F_gravity = m * g * sin(angle)
where m = 10 kg (mass of the box), g = 9.81 m/s² (acceleration due to gravity), and angle = 60 degrees.
F_gravity = 10 * 9.81 * sin(60) ≈ 85.0 N
The maximum static friction force can be calculated using:
F_friction = μ * N
where μ = 0.2 (coefficient of static friction) and N = m * g * cos(angle) (normal force).
N = 10 * 9.81 * cos(60) ≈ 49.05 N
F_friction = 0.2 * 49.05 ≈ 9.81 N
To prevent the box from sliding, the applied force should be equal to the difference between the gravitational force along the incline and the maximum static friction force:
F_applied = F_gravity - F_friction
F_applied = 85.0 N - 9.81 N ≈ 75.19 N
Therefore, a force of approximately 75.19 N must be applied on the box to prevent it from sliding down the inclined plane.
To know more about Friction click here .
brainly.com/question/28356847
#SPJ11
a turbine operates group of answer choices by turning a generator to create a flow of charges, a current. by taking energy from a low temperature reservoir and depositing it in a high temperature reservoir. like a solar panel. like a windmill. by turning a diode to create a flow of charges, a current. by taking energy from a high temperature reservoir and depositing it in a low temperature reservoir.
A turbine operates by turning a generator to create a flow of charges, a current. This process involves taking energy from a high temperature reservoir (such as steam or hot gas) and using it to spin the turbine blades. Option B is Correct
As the blades rotate, they turn the generator, which converts the mechanical energy into electrical energy. This electrical energy can then be used to power homes, businesses, and other devices. So, the correct answer is "by taking energy from a high temperature reservoir and depositing it in a low temperature reservoir."
Electrical energy is converted into mechanical energy, which is an accurate description of the scenario.
As the circuit is closed, electrons begin to flow in the wires, producing electricity. This current then reaches the fan, which rotates due to the magnets inside it. As a result, electrical energy is converted into mechanical energy, or the kinetic energy generated by the rotation of a fan's wing.
Learn more about mechanical energy here
https://brainly.com/question/29408366
#SPJ11
a 300-turn solenoid has a radius of 5 cm and a length of 20 cm. find the energy stored in it when the current is 0.5 a.
The energy stored in the solenoid when the current is 0.5 A is 0.001J.
The energy stored in a solenoid can be calculated using the formula:
E = (1/2) * L * I^2
where E is the energy stored in joules (J), L is the inductance of the solenoid in henries (H), and I is the current flowing through the solenoid in amperes (A).
The inductance of a solenoid can be calculated using the formula:
L = (μ * N^2 * A) / l
where L is the inductance in henries, μ is the permeability of free space (4π x 10^-7 H/m), N is the number of turns, A is the cross-sectional area of the solenoid, and l is the length of the solenoid.
In this case, the solenoid has 300 turns, a radius of 5 cm (0.05 m), and a length of 20 cm (0.2 m), so:
A = π * r^2 = 3.14 * 0.05^2 = 0.00785 m^2
l = 0.2 m
N = 300
μ = 4π x 10^-7 H/m
Therefore, the inductance of the solenoid is:
L = (4π x 10^-7 H/m) * (300^2) * (0.00785 m^2) / 0.2 m = 0.00925 H
Now we can use the formula for energy to calculate the energy stored in the solenoid when the current is 0.5 A:
E = (1/2) * L * I^2 = (1/2) * 0.00925 H * (0.5 A)^2 = 0.00115 J
to know more about solenoid refer here:
https://brainly.com/question/15576393#
#SPJ11
To find the energy stored in the solenoid, we'll need to calculate its inductance first and then use the formula for energy storage in an inductor.
1. Calculate the inductance (L) of the solenoid:
L = (μ₀ * N² * A) / l, where μ₀ is the permeability of free space (4π x 10⁻⁷ Tm/A), N is the number of turns, A is the cross-sectional area, and l is the length of the solenoid.
A = πr² = π(0.05 m)² = 0.00785 m² (radius converted to meters)
L = (4π x 10⁻⁷ Tm/A * 300² * 0.00785 m²) / 0.2 m = 0.0353 H (henries)
2. Calculate the energy stored (E) in the solenoid:
E = (1/2) * L * I², where I is the current.
E = (1/2) * 0.0353 H * (0.5 A)² = 0.0044125 J (joules)
So, the energy stored in the 300-turn solenoid with a radius of 5 cm, a length of 20 cm, and a current of 0.5 A is approximately 0.0044 J (joules).
Learn more about current here:
https://brainly.com/question/2424523
#SPJ11
A man pushes on a 75.0 kg box such that his force of 225 N is exerted at an angle of 27.0 to the horizontal as shown
a) If the floor exerts a frictional force of 44.0 N on the box, what is the net force acting on the box?
b) If the box is initally at rest, how far will it have been pushed in 5.00 s assuming thise forced continued
a) The net force acting on the box is 181 N at an angle of 17.3 degrees below the horizontal.
b) The box will have been pushed 2.26 m assuming the force is constant.
a) To find the net force, we need to resolve the applied force vector into horizontal and vertical components. The horizontal component is 225cos(27.0) = 196 N and the vertical component is 225sin(27.0) = 102 N. The frictional force acts in the opposite direction to the horizontal component, so the net force in the horizontal direction is 196 - 44 = 152 N.
The net force in the vertical direction is 102 N - 750 N (weight of the box) = -648 N. Using the Pythagorean theorem, the magnitude of the net force is sqrt((152 N)² + (-648 N)²) = 670 N. The angle between the net force and the horizontal is arctan(-648 N/152 N) = -17.3 degrees below the horizontal.
b) We can use the kinematic equation d = 1/2at² to find the distance the box travels in 5.00 s, where a is the acceleration of the box and t is the time. The net force in the horizontal direction is responsible for the acceleration of the box, so we can use F = ma to find the acceleration: a = F/m = 152 N/75.0 kg = 2.03 m/s².
Substituting into the kinematic equation, we get d = 1/2 * 2.03 m/s² * (5.00 s)² = 25.3 m. However, this assumes that the force is constant, which may not be true in reality.
To learn more about frictional force, here
https://brainly.com/question/30280752
#SPJ1
Question 26
A major part of the Earth Summit was to:
a. stabilize concentrations of greenhouse gases at 1990 levels
b. fine nations that did not comply with the accord
c. conduct joint national research about the environment
d. decrease the amount of fossil fuel consumption
A major part of the Earth Summit was to stabilize concentrations of greenhouse gases at 1990 levels.
Stabilize Concentrations of Greenhouse Gases at 1990 Levels: One of the main goals of the Earth Summit was to stabilize concentrations of greenhouse gases in the atmosphere at 1990 levels. This was done by encouraging countries to reduce their emissions of greenhouse gases, such as carbon dioxide and methane, through the use of renewable energy sources and energy efficiency improvements. This would help to reduce the rate of global warming and address climate change.
To learn more about Greenhouse Gases click here https://brainly.com/question/23268735
#SPJ11
Question 63 Marks: 1 The limitation of the lift capability of the centrifugal pump is based onChoose one answer. a. the weight of the atmosphere b. the design of the impeller and volute c. the efficiency of the motor d. the effect of friction
The limitation of the lift capability of the centrifugal pump is based on the design of the impeller and volute. Option B is the correct answer.
The limitation of the lift capability of a centrifugal pump is based on the design of the impeller and volute.
Centrifugal pumps work by converting rotational energy from a motor into hydrodynamic energy in the fluid. The impeller is the primary rotating component in the pump that draws fluid in through the inlet and accelerates it radially outward towards the volute.
The volute is a stationary casing that converts the kinetic energy of the fluid into pressure energy.
The design of the impeller and volute determines the maximum head or lift that can be achieved by the pump. If the pump is required to lift fluid to a greater height, then a multistage pump can be used.
Learn more about centrifugal pumps at
https://brainly.com/question/30356820
#SPJ4
What is the wavelength of a radio wave traveling in a vacuum that has a frequency of 7.80x10^7Hz?
The wavelength of the radio wave with a frequency of 7.80×10⁷ Hz is 3.846 m.
The wavelength and frequency are inversely proportional to each other. The frequency of the wave gives the number of oscillations per unit of time.
The wavelength is defined as the distance between crests and troughs and the unit of wavelength is a meter.
From the given,
frequency (ν) = 7.80×10⁷ Hz
wavelength (λ) =?
frequency (ν) = c / λ, where c is the velocity of light and λ is the wavelength.
λ = c/ν
= (3×10⁸ m/s) / (7.80×10⁷ Hz)
= 3.846 m
Thus, the wavelength of the radio wave is 3.846m.
To know more about the wavelength of waves:
https://brainly.com/question/9780095
#SPJ1
inductive load connect to 120 v(rms) 60 hz ac source draws 5kw at a power factor of 0.8. calculate the capacitance
A capacitance of 11.81 microfarads (μF) would be required to correct the power factor of the inductive load.
To calculate the capacitance required to correct the power factor of the inductive load, we need to use the following formula:
C = (1000 * P * tan(φ)) / (2π * f * V^2)
Where:
- C is the capacitance in Farads
- P is the apparent power in VA (volt-amperes)
- φ is the phase angle between voltage and current
- f is the frequency in Hz
- V is the voltage in volts
Given:
- V = 120 V (rms)
- f = 60 Hz
- P = 5 kW = 5000 VA
- power factor = 0.8
- we know that power factor = cos(φ)
So, we can calculate the phase angle as:
φ = acos(power factor) = acos(0.8) = 36.87 degrees
Then, we can calculate the reactive power as:
Q = P * tan(φ) = 5000 * tan(36.87) = 3644.67 VAR (volt-ampere reactive)
Now, we can use the formula to calculate the capacitance:
C = (1000 * P * tan(φ)) / (2π * f * V^2) = (1000 * 5000 * tan(36.87)) / (2π * 60 * 120^2) = 11.81 microfarads (μF)
To learn more about voltage click here
brainly.com/question/13521443
#SPJ11
A wheel of radius 0.5 m rotates with a constant angular speed about an axis perpendicular to its center. A point on the wheel that is 0.2 m from the center has a tangential speed of 2 m/s.
28. Determine the angular speed of the wheel.
A) 0.4 rad/s
B) 2.0 rad/s
C) 4.0 rad/s
D) 10 rad/s
E) 20 rad/s
The angular speed of the wheel is 10 rad/s, when the wheel that is 0.2 m from the center has a tangential speed of 2 m/s.
To determine the angular speed of the wheel, we can use the formula relating tangential speed (v) with angular speed (ω) and radius (r):
v = ω * r
In this case, we are given the tangential speed (v = 2 m/s) and the radius of the point (r = 0.2 m). We need to find the angular speed (ω). Rearranging the formula to solve for ω:
ω = v / r
Substituting the given values:
ω = 2 m/s / 0.2 m
ω = 10 rad/s
So, the angular speed of the wheel is 10 rad/s. The correct answer is D) 10 rad/s.
learn more about angular speed Refer: https://brainly.com/question/14528696
#SPJ11
If your car has a mass of 741 kg, how much force is required to accelerate it forward at 4.88 m/s2?
Newton's second law states that force is proportional to what is required for an object of constant mass to change its velocity. This is equal to that object's mass multiplied by its acceleration. We use Newtons, kilograms, and meters per second squared as our default units, although any appropriate units for mass
To calculate the force required to accelerate the car forward at 4.88 m s2, we need to use the formula F = m x a, where F is force, m is mass, and a is acceleration. F = 741 kg x 4.88 m/s2F = 3,613.08 N Therefore, a force of 3,613.08 Newtons is required to accelerate the car forward at 4.88 m s2. We use Newtons, kilograms, and meters per second squared as our default units, although any appropriate units for mass or velocity (miles per hour per second, millimeters per second2, etc. could certainly be used as well - the calculation is the same regardless.
learn more about accelerate here
https://brainly.com/question/28811174
#SPJ11
What is the SI unit used to measure temperature?
Joule
Celcius
farenheit
Kelvin
The SI unit used to measure temperature is Kelvin (K).
Definition -
The kelvin, symbol K, is the primary unit of temperature in the International System of Units, used alongside its prefixed forms and the degree Celsius. It is named after the Belfast-born and University of Glasgow-based engineer and physicist William Thomson, 1st Baron Kelvin In 1954, the kelvin was defined as equal to the fraction 1⁄273.16 of the thermodynamic temperature of the triple point of water—the point at which water, ice and water vapor co-exist in equilibrium
To learn more about si units -
brainly.com/question/12629581
#SPJ11
The fusible plug that is in all chlorine containers?
a. May be used as a tap for the chlorine source
b. Should be removed after the cylinders are empty
c. Should never be removed or tampered with
d. Should be removed prior to withdrawing chlorine from the container
d. Should be removed prior to withdrawing chlorine from the container. The fusible plug is designed to melt at a specific temperature in case of a fire, releasing the pressure inside the container and preventing an explosion.
However, if the plug is still in place when chlorine is being withdrawn, it can cause the chlorine to react with the metal plug and potentially create a dangerous situation. Therefore, it is important to remove the fusible plug before withdrawing chlorine from the container. Removing or tampering with the fusible plug could lead to hazardous situations when withdrawing chlorine. Always follow proper safety guidelines and procedures when handling chlorine containers.
Learn more about chlorine here:
brainly.com/question/11026469
#SPJ11
The main valve in a pilot-operated four-way reversing valve is moved by pressure created by ___.a. refrigerant boiling in the coilb. pressure reduction in the condenserc. change in the action of the metering deviced. low and high side pressure difference
The main valve in a pilot-operated four-way reversing valve is moved by pressure created by the difference in low and high side pressure.
The metering device plays a role in regulating the flow of refrigerant, but it is not directly involved in operating the valve. The valve is controlled by a pilot valve that responds to pressure differences in the system, allowing the valve to switch between different flow paths as needed.
The main valve in a pilot-operated four-way reversing valve is moved by pressure created by d. low and high side pressure difference. This pressure difference allows the valve to be operated effectively, ensuring proper metering and flow control within the system.
To know more about Pressure click here .
brainly.com/question/12971272
#SPJ11
Relación de conceptos e ideas:
1. Mantiene la integridad de los átomos, de las moléculas y de todos los cuerpos con los que nos relacionamos.
2. Científico cuyo nombre reciben las ecuaciones fundamentales del electromagnetismo.
4. Científico a quien se debe la idea de líneas de campo.
5. Científico que se considera el descubridor del electrón.
6. Científico a quien se debe la ley de la fuerza entre dos partículas cargadas en reposo.
7. Partículas responsables de que haya dos tipos de electricidad.
8. Nombre que recibe la cantidad mínima de carga eléctrica.
9. Instrumento utilizado por Coulomb para establecer la ley que lleva su nombre.
10. Ente que rodea a todo cuerpo cargado eléctricamente y que actúa sobre otros cuerpos con carga.
11. Nombre de la magnitud utilizada para caracterizar el campo eléctrico.
12. Líneas en el espacio que rodea a un cuerpo cargado, empleadas para caracterizar su campo eléctrico.
13. Energía de un sistema de cuerpos electrizados debida a la interacción eléctrica entre ellos.
14. Variación de la energía potencial por unidad de carga que tiene lugar cuando una partícula cargada se desplaza entre dos puntos de un campo eléctrico.
15. Nombre que comúnmente reciben en Física los aisladores.
16. Materiales en que los centros de carga positiva y negativa de sus moléculas no coinciden.
17. Materiales en que los centros de carga positiva y negativa de sus átomos o moléculas coinciden.
18. Cociente entre la magnitud del campo en el que se coloca un material y la magnitud del campo que resulta en su interior.
19. Dispositivo que puede ser empleado para acumular carga eléctrica y energía.
20. Magnitud que indica la carga eléctrica por voltio que puede almacenar un condensador.
21. Energía por unidad de volumen del campo eléctrico.
Respuestas
( ) Balanza de torsión
( ) Campo eléctrico
( ) Carga eléctrica elemental
( ) Charles A. Coulomb
( ) Circuito eléctrico
( ) Condensador
( ) Constante dieléctrica
( ) Densidad de energía
( ) Dieléctricos
( ) Dieléctricos no polares
( ) Dieléctricos polares
( ) Diferencia de potencial
( ) Electrones y protones
( ) Energía potencial eléctrica
( ) Intensidad de campo eléctrico
( ) Interacción electromagnética
( ) James C. Maxwell
( ) Joseph J. Thomson
( ) Líneas de campo eléctrico
( ) Michael Faraday
The terms for the statements given are, 1. Conservation of Matter, 2. James Clerk Maxwell, 3. Michael Faraday, 4. J.J. Thomson, 5. Charles-Augustin de Coulomb, 6. Electrons and protons, 7. Elementary charge, 8. Torsion balance, 9. Electric field, 10. Electric field strength, 11. Electric field lines, 12. Electrical potential energy, 13. Electric potential difference, 14. Dielectrics, 15. Polar materials, 16. Nonpolar materials, 17. Dielectric constant, 18. Capacitor, 19. Capacitance, 20.Electric energy density.
Fundamental forces, including electromagnetism, maintain atoms and bodies we interact with. Maxwell's equations unified electricity and magnetism. Faraday introduced field lines to visualize electric and magnetic fields. Thomson discovered electrons, while Coulomb established the law of force between charged particles. Protons and electrons create positive and negative electricity, and an elementary charge is the smallest charge carried by a single particle.
The electric field surrounds charged bodies and has a strength measured in volts per meter. Insulators prevent electrical flow and are useful in electronics. Polar and nonpolar materials have different arrangements of positive and negative charges. The dielectric constant measures the ratio of field magnitudes in and out of a material. Capacitors store electric charge and energy and have capacitance measured in farads. Electric energy density measures the energy per unit volume of the electric field.
To know more about electric field, here
https://brainly.com/question/15800304
#SPJ4
(348) The maximum run length of 3/8 inch flexible metal conduit for any circuit is_____ feet.
For any circuit, a run of 3/8 inch flexible metal conduit cannot exceed 6 feet in length.
The National Electrical Code (NEC) states that the conduit size and wire size together determine the maximum length of a flexible metal conduit run for any circuit. The longest length for any circuit with a flexible metal conduit of 3/8 inch is 6 feet. This prevents an excessive voltage drop in the circuit brought on by the conductor's resistance, which could present a fire hazard. Based on a voltage drop of 3% or less at the circuit's rated current, the maximum length is determined. To ensure secure and effective electrical installations, it's crucial to adhere to the NEC regulations.
learn more about flexible metal here:
https://brainly.com/question/29564551
#SPJ4
a 1000-n skydiver opens his parachute and experiences an air resistance force of 300 n. the net force on the parachutist is
The net force on the skydiver after opening the parachute can be calculated by subtracting the air resistance force from the gravitational force acting on the skydiver.
After opening the parachute, the skydriver experiences the air resistance force of 300 N is acting in the opposite direction of the force of gravity (which is 1000 N), so the net force is the difference between the two:
Net force = force of gravity - air resistance force
Net force = 1000 N - 300 N
Net force = 700 N
Therefore, the net force on the skydiver after opening the parachute would be 700 N. This net force is still directed downwards, but is lower than the gravitational force acting on the skydiver before opening the parachute. This allows the parachute to slow down the descent of the skydiver by providing additional air resistance.
Learn more about air resistance here:
https://brainly.com/question/8141158
#SPJ11
The net force on the skydiver can be calculated using the equation:
net force = force of gravity - force of air resistance
The force of gravity on the skydiver can be calculated using the formula:
force of gravity = mass x acceleration due to gravity
where mass is the mass of the skydiver and acceleration due to gravity is approximately 9.81 m/s^2.
Given that the mass of the skydiver is 1000 N ÷ 9.81 m/s^2 ≈ 102.03 kg, the force of gravity acting on the skydiver is:
force of gravity = 102.03 kg x 9.81 m/s^2 ≈ 1000 N
Substituting this and the force of air resistance, which is 300 N, into the net force equation gives:
net force = 1000 N - 300 N = 700 N
Therefore, the net force acting on the skydiver is 700 N.
To know more about net force visit link :
https://brainly.com/question/29261584
#SPJ11
Terminal Rating(110-14(C)(1): Terminals for equipment rated over 100 ampere and pressure connector terminals for conductors larger than No. 1 shall have the conductor sized according to 75 degree C temperature rating as listed in Table 310-15(a)(16)(True/False)
True. According to the Terminal Rating (110-14(C)(1)) in the National Electrical Code (NEC), terminals for equipment rated over 100 ampere and pressure connector terminals for conductors larger than No. 1
It must have the conductor sized according to the 75 degree C temperature rating as listed in Table 310-15(a)(16). This is to ensure that the terminals and connectors are properly sized and can handle the electrical load without overheating. The statement "Terminal Rating (110-14(C)(1)): Terminals for equipment rated over 100 ampere and pressure connector terminals for conductors larger than No. 1 shall have the conductor sized according to 75 degree C temperature rating as listed in Table 310-15(a)(16)" is True.
According to the National Electrical Code (NEC), terminals for equipment rated over 100 ampere and pressure connector terminals for conductors larger than No. 1 are required to have their conductors sized based on the 75 degree C temperature rating listed in Table 310-15(a)(16). This ensures proper conductor sizing and safe operation under the specified temperature and pressure conditions.
Visit here to learn more about National Electrical Code (NEC):
brainly.com/question/30757813
#SPJ11
the triple alpha processgroup of answer choicescontrols the pulsations in cepheid variable stars.is the nuclear fusion of hydrogen to helium in massive stars.is the process that produces the neutrinos we receive from the sun.requires a temperature of about 5,000,000 k to operate.occurs during helium flash.
The triple alpha process is a nuclear fusion process that occurs during helium flash and is responsible for the production of helium in massive stars. It requires a temperature of about 5,000,000 K to operate and produces the neutrinos we receive from the sun.
These not directly related to the pulsations in cepheid variable stars, which are controlled by other factors such as the star's mass and composition. The triple alpha process is the nuclear fusion of hydrogen to helium in massive stars. This process requires a temperature of about 5,000,000 K to operate and occurs during helium flash. It is not directly related to the pulsations in Cepheid variable stars or the production of neutrinos we receive from the sun.
learn more about helium here.
https://brainly.com/question/31219107
#SPJ11
(240) A department store ( continuous load) feeder supplies a lighting load of 103 ampere. The minimum size overcurrent protection device permitted for this feeder is _____ ampere.
A department store ( continuous load) feeder supplies a lighting load of 103 ampere. The minimum size overcurrent protection device permitted for this feeder is 150 ampere.
In the event that the base size overcurrent security gadget allowed for a retail chain feeder providing a constant lighting heap of 103 amps is 150 amps, it wouldn't be consistent with the NEC rules. According to NEC, the overcurrent assurance gadget for consistent burdens ought to be evaluated somewhere around 125% of the ceaseless burden, which for this situation would be:
Least size = 125% x 103 amps
Least size = 128.75 amps
Consequently, a base size overcurrent insurance gadget of 150 amps wouldn't be satisfactory for shielding the circuit from over-burdening or short-circuiting, and it would represent a security risk. It is critical to adhere to the NEC rules to guarantee the wellbeing of the electrical framework and the structure tenants.
To learn more about overcurrent protection device, refer:
https://brainly.com/question/28283140
#SPJ4
5. A series LRC circuit is driven on resonance with a driving voltage amplitude of V0=1.0V. If the quality factor Q=20.0, what is the amplitude VR of the voltage across the resistor in V.
The amplitude VR of the voltage across the resistor in a series LRC circuit driven on resonance with a driving voltage amplitude of V0=1.0V and Q=20.0 is 20.0V.
In a series LRC circuit, the voltage across the resistor is determined by the equation VR = QV0, where Q is the circuit's quality factor and V0 is the driving voltage's amplitude. The impedance of the inductor and capacitor cancel out when the circuit is driven on resonance, leaving just the resistance of the resistor. The quality factor is defined as Q = R(C/L) at resonance, where R is the resistance, C is the capacitance, and L is the circuit's inductance. We may calculate VR by plugging in the supplied values for V0 and Q:
[tex]VR=QV0=20.0 x 1.0V=20.0V[/tex]
As a result, the voltage across the resistor has an amplitude VR of 20.0V.
learn more about LRC circuit here:
https://brainly.com/question/29045377
#SPJ11
(332-100) Flat cable assembly shall consist of 2, 3 or 4 conductors.(True/False)
True. According to the statement, the flat cable assembly shall consist of 2, 3 or 4 conductors. Conductors are the wires or cables that conduct electricity through a circuit or system.
In this case, the flat cable assembly is designed to have either two, three, or four conductors, which means that it can carry electrical signals or power through these wires. Flat cable assemblies are commonly used in electronic devices or systems where space is limited, and a flat, flexible cable is required. They are often used in applications such as computers, printers, televisions, and medical equipment. The number of conductors in a flat cable assembly can affect the performance and capabilities of the device or system that it is used in. Therefore, it is essential to follow the specifications and requirements stated in the statement to ensure that the flat cable assembly meets the necessary standards and functions correctly.According to the statement, the flat cable assembly shall consist of 2, 3 or 4 conductors. Conductors are the wires or cables that conduct electricity through a circuit or system.
learn more about circuit here
https://brainly.com/question/21505732
#SPJ11
A 100-kg fisherman and a 500-kg supply crate are on a frozen pond that is essentially frictionless. The man and the crate are initially separated by a distance of 600 meters. The fisherman uses a very light rope to pull the crate closer to him. How far has the man moved when the crate reaches the fisherman
The fisherman will move a distance of 100 meters when the crate reaches him.
Since there is no friction on the ice, the force applied by the fisherman on the rope will result in an equal and opposite force on the fisherman himself.
The fisherman's mass is 100 kg, while the crate's mass is 500 kg, which means that the force applied on the rope will result in a much greater acceleration for the crate than for the fisherman.
This means that the crate will cover the 600-meter distance much faster than the fisherman, but once the crate reaches the fisherman, the rope will become taut and the fisherman will start to move towards the crate.
Since the force applied on the rope is constant, the acceleration of the fisherman will also be constant, and he will move a distance of 100 meters by the time the crate reaches him.
The fisherman will move a distance of 100 meters when the crate reaches him due to the equal and opposite force applied on him by the rope.
For more information on force on crate kindly visit to
https://brainly.com/question/24328254
#SPJ11
an incubator is used to keep chicken eggs warm. the air temperature inside the incubator is at 38oc that leads to a heat transfer coefficient of 2 w/m2 k. the initial temperature of the egg is 20oc. assume the egg to be spherical with a volume of 60 cm3 , density of 1035 kg/m3 , specific heat capacity of 3350 j/kg-k and thermal conductivity of 0.62 w/mk. a. calculate the temperature of the center of the egg after 30 minutes (10 points) b. if the environment inside the incubator is modified to have a heat transfer coefficient of 104 w/m2 k, what is the temperature of the egg after 30 minutes?
The temperature of the center of the egg after 30 minutes with the new heat transfer coefficient is: 20°C + 3.6°C = 23.6°C.
a. To calculate the temperature of the center of the egg after 30 minutes, we need to use the following formula:
q = (4/3)πr^3 ρc ΔT
where q is the amount of heat transferred, r is the radius of the egg, ρ is the density of the egg, c is the specific heat capacity of the egg, and ΔT is the temperature difference between the initial temperature of the egg and the final temperature.
First, we need to calculate the radius of the egg using its volume:
V = (4/3)πr^3
60 cm^3 = (4/3)πr^3
r = 1.87 cm
Next, we need to calculate the amount of heat transferred:
q = (4/3)π(1.87 cm)^3 (1035 kg/m^3) (3350 J/kg-K) (38°C - 20°C)
q = 219,977 J
Finally, we can calculate the final temperature of the center of the egg using the following formula:
q = (4/3)πr^3 ρc ΔT
ΔT = q / ((4/3)πr^3 ρc)
ΔT = 219,977 J / ((4/3)π(1.87 cm)^3 (1035 kg/m^3) (3350 J/kg-K))
ΔT = 19.6°C
Therefore, the temperature of the center of the egg after 30 minutes is:
20°C + 19.6°C = 39.6°C
b. If the heat transfer coefficient is increased to 104 W/m^2 K, we can use the same formula as above to calculate the temperature of the center of the egg after 30 minutes. However, we need to use the new heat transfer coefficient in the formula:
q = (4/3)πr^3 ρc ΔT = hAΔT
where h is the new heat transfer coefficient and A is the surface area of the egg.
We can calculate the surface area of the egg using its radius:
A = 4πr^2
A = 44.1 cm^2
Now, we can calculate the amount of heat transferred:
q = hAΔT = 104 W/m^2 K (0.00441 m^2) (38°C - 20°C)
q = 4,046 J
Finally, we can calculate the final temperature of the center of the egg:
q = (4/3)πr^3 ρc ΔT
ΔT = q / ((4/3)πr^3 ρc)
ΔT = 4,046 J / ((4/3)π(0.0187 m)^3 (1035 kg/m^3) (3350 J/kg-K))
ΔT = 3.6°C
Therefore, the temperature of the center of the egg after 30 minutes with the new heat transfer coefficient is: 20°C + 3.6°C = 23.6°C.
Visit here to learn more about temperature : https://brainly.com/question/12035620
#SPJ11
You want to walk down your icy driveway without sliding.
Part A
If the incline of the driveway is 23 â from the horizontal, what must the minimum coefficient of static friction be between your shoes and the ice?
The minimum coefficient of static friction needed between your shoes and the ice to prevent sliding down the driveway is approximately 0.424.
To determine the minimum coefficient of static friction needed to prevent sliding down the icy driveway, we need to use the formula:
μ_s = tanθ
where μ_s is the coefficient of static friction and θ is the angle of incline in radians.
First, we need to convert the angle from degrees to radians:
θ = 23° = (23/180)π rad = 0.4014 rad
Now we can plug in the values:
μ_s = tan(0.4014) ≈ 0.424
Therefore, the minimum coefficient of static friction needed between your shoes and the ice to prevent sliding down the driveway is approximately 0.424.
To know more about static friction; click here:
https://brainly.com/question/13680415
#SPJ11
A microscope with an 9.0-mm -focal-length objective has a tube length of 18.0cm
For the microscope to be in focus, how far should the objective lens be from the specimen?
The objective lens should be 9.0 cm from the specimen in order for the microscope to be in focus.
What is microscope?A microscope is an instrument used to magnify objects that are too small to be seen with the nak ed eye. It consists of a lens system that collects light from the object and produces a magnified image in the eyepiece. A microscope can be used to observe bacteria, cells, and other microscopic organisms, and to analyze materials at the atomic and molecular level. Microscopes have become an essential tool in the fields of biology, medicine, and scientific research. They have also been used to observe and measure the texture, color, and structure of materials in the arts and manufacturing.
This is because the focal length of an objective lens is defined as the distance from the lens to the focal point, which is the point at which light rays coming from a distant object converge to a sharp focus. Therefore, since the focal length of the objective lens is 9.0 mm, the lens should be 9.0 cm from the specimen in order to be in focus.
To learn more about microscope
https://brainly.com/question/12993552
#SPJ4