1- charging by touch occurs when electrons are transmitted by direct contact.
(Right)
(wrong)

2- Electric charges are preserved, they are not created or destroyed.
(Right)
(wrong)​

Answers

Answer 1

Answer:

#1 - True (touch) charging when electric conductors actually touch one another.

#2. True - electrical charges are conserved (not destroyed)


Related Questions


In an application, Germanium is
made p-type material by adding
Indium. The rate of adding is one
indium atom
per
3 Germanium
atom. Assume donor density to be
zero and ni = 6.2 Cubic
metre at room temperature.
Determine the value
of
the
aceeptor atom density​

Answers

Answer:

produce electronics

Explanation:

The uses of Germanium are recorded beneath: Germanium's principle use is to deliver strong state hardware, semiconductors and fiber optic frameworks. As a phosphor in fluorescent lights.

A hand dryer blows heated air downwards out of the exit duct at a velocity of 4 m/s. The temperature and density of the ambient air at the inlet are 15 C and 1.23 kg/m3, while at the outlet it has temperature 35 C and density 1.15 kg/m3 The blower power is 10.0 W and the heater power is 715 W. Consider the inlet to be at the large mass of ambient air which has negligible velocity.
a) What is the pressure at the outlet? 4 m/s, 35 C
b) You will be applying the energy equation. Why can you ignore any height differences in this situation?
c) If the specific heat of air C-1000 J/(kg K), where Δυ-C Δ T, find the change in internal energy per unit mass from the inlet to outlet.
d) Find the mass flow rate through the dryer.
e) What is the power loss in the system?
f) What is the loss in the system?
g) What is the head loss in the system?
h) What is the total loss coefficient of the system, referred to the outlet velocity?
i) If there were no heater, would the temperature of gas at the outlet be higher, the same, or lower than the inlet? Explain why.

Answers

Answer:

nzkdjdksishdjsdjjdjnzkskejeoueeuieeoyrie ryrhdhcksodopdncndnszdkhfoeosheiwuef wokxkzdkjdoeehxjbxbdkeiehdhdhddjjddjdhhdhdhhhjdhfjdjjfjddhdheudiwiehdbejwowud

Explanation:

isos

A carnival ride starts at rest and is accelerated from an initial angle of zero to a final angle of 6.3 rad by a rad counterclockwise angular acceleration of 2.0 s2 What is the angular velocity at 6.3 rad?​

Answers

The final angular velocity of the carnival ride at a displacement of 6.3 rad is 25.2 rad/s.

Final angular velocity of the carnival ride

The final angular velocity of the carnival ride is determined by applying third kinematic equation as shown below;

ωf = ωi + 2αθ

where;

ωf  is the final angular velocity of the carnival ride = ?ωi is the initial angular velocity of the carnival ride = 0α is the angular acceleration = 2.0 rad/s²θ is the angular displacement of the carnival ride = 6.3 rad

ωf = 0 + 2(2.0) x 6.3

ωf = 25.2 rad/s

Thus, the final angular velocity of the carnival ride at a displacement of 6.3 rad is 25.2 rad/s.

Learn more about angular velocity here: https://brainly.com/question/6860269

Answer: 5.0 rad/s

Explanation: Because that’s what khan said so try it out.

Your eyes form upside-down images, which are then flipped right-side-up by our brains.


True
False

Answers

Answer:

I believe it is true, but our brains don’t do it, I think it is the lenses in our eyes that do it. I might be wrong tho

Explanation:

Answer:

Yes it is true that our eyes form upside-down images, which are flipped right-side-up by our brain.

When you cool a gas, how does this affect the de Broglie wavelength of the gas atoms? When you cool a gas, how does this affect the de Broglie wavelength of the gas atoms? Being cooled, the gas atoms slow down so that their de Broglie wavelength will increase. Being cooled, the gas atoms slow down so that their de Broglie wavelength will decrease. The de Broglie wavelength will remain the same because it does not depend on temperature.

Answers

Answer:

The de Broglie wavelength will remain the same because it does not depend on temperature.

Explanation:

de Broglie wavelength of a particle is independent of the temperature and hence the properties of emitted particle such as photoelectric effect, radioactive radiation etc. does not depend on the temperature.

Also, until unless the kinetic energy of a moving particle is not driven by the

thermal energy, the de Broglie wavelength  is independent of the temperature

One hazard of space travel is debris left by previous missions. There are several thousand objects orbiting Earth that are large enough to be detected by radar, but there are far greater numbers of very small objects, such as flakes of paint. The force exerted by a 0.100-mg chip of paint that strikes a spacecraft window at a relative speed of 4.00 x 103 m/s, given the collision lasts 6.00 x 10-8 s is Fill input: x 106 N.

Answers

Answer:

The correct answer is "6666.67 N".

Explanation:

The given values are:

Mass,

m = 0.100

Relative speed,

v = 4.00 x 10³

time,

t = 6.00 x 10⁻⁸

As we know,

⇒  [tex]F=m(\frac{\Delta v}{\Delta t} )[/tex]

On substituting the given values, we get

⇒      [tex]=0.100\times 10^{-6}(\frac{4\times 10^3}{6\times 10^{-8}} )[/tex]

⇒      [tex]=6666.67 \ N[/tex]

Which device converts electric energy into mechanical energy?
O A. An electromagnet
O B. A motor
O C. A transformer
O D. A generator

Answers

Answer:

B motor

Explanation:

what is the velocity of the object 2.3 seconds after it is released from the top of the empire state building?

Answers

Explanation:

Object is under the effect of the acceleration of gravity

v = 1/2 a t^2       a = 9.81 m/s^2   t = 2.3

v = 25.9 m/s^2 = ~ 26 m/s   ( two significant digits)

Help please. Question about a potential energy.

Answers

P=m*g*h. So this implies that 130*10*0.200=260J. Bear in mind that g is constant.

A 6.47 micro-coloumb particle moves through a region of space where an electric field of magnitude 1300 N/C points in the positive x direction, and a magnetic field of magnitude 1.33 T points in the positive z direction. If the net force acting on the particle is 6.27E^-3 N in the positive x direction>

Required:
Calculate the magnitude of the particle's velocity. Assume the particle's velocity is in the xy plane.

Answers

Answer:

v = 248.8 m/s

Explanation:

Given that,

Charge, q = [tex]6.47\ \mu C[/tex]

Electric field, E = 1300 N/C

Magnetic field, B =1.33 T

The force acting on the particle, [tex]F=6.27\times 10^{-3}\ N[/tex]

We need to find the magnitude of the particle's velocity. The net force on the particle is given by :

[tex]F=qE+qvB\\\\6.27\times 10^{-3}=6.47\times 10^{-6}\times 1300+6.47\times 10^{-6}\times 1.33v\\\\6.27\times 10^{-3}-6.47\times 10^{-6}\times 1300=6.47\times 10^{-6}\times 1.33v\\\\-0.002141=6.47\times 10^{-6}\times 1.33v\\\\v=\dfrac{0.002141}{6.47\times 10^{-6}\times 1.33}\\\\v=248.8\ m/s[/tex]

So, the magnitude of the particle's velocity is 248.8 m/s.

what is the stress in a steel wire that is 5m long and 0.04cm squared in cross section If the wire bears a load of 20kg?

Answers

Answer:

Explanation:

stress = ?

length =5 m

area of cross section = 0.04 cm or 0.0004m

force = 20 × 10 = 200 N ( w = mg) g = 10

formula : stress = force / cross-sectional area

stress = 200 / 0.0004

stress = 500,000 Nm^-2

please help me !
1. Suppose that the temperature drops 25 degrees overnight. When you get into your car the next morning, your low tire pressure light comes on. Explain, in terms of the ideal gas law, why this happened (assume air is an ideal gas). (10 points)

Answers

Answer:

The drop in temperature overnight causes a decrease in the average kinetic energy of the air molecules inside the tires. According to the ideal gas law, this leads to a decrease in tire pressure. The low tire pressure light in vehicles is triggered when the pressure falls below a certain threshold, alerting the driver to check and adjust the tire pressure.

Explanation:

The ideal gas law, represented by the equation PV = nRT, relates the pressure (P), volume (V), number of moles (n), and temperature (T) of an ideal gas. In this case, we can analyze how the drop in temperature affects the tire pressure.

When the temperature drops, according to the ideal gas law, the pressure of a gas will decrease if the volume and the number of moles remain constant. This is because the decrease in temperature causes a decrease in the average kinetic energy of the gas particles, leading to less frequent and less forceful collisions with the tire walls, resulting in a decrease in pressure.

In the context of the tire pressure, the air inside the tires behaves as an ideal gas. When the temperature drops overnight, the air inside the tires also cools down, causing a decrease in its temperature. As a result, the average kinetic energy of the air molecules decreases, leading to a decrease in pressure inside the tires.

The low tire pressure light comes on as a result of this drop in pressure. The tire pressure monitoring system in modern vehicles is designed to detect significant deviations from the recommended tire pressure. When the pressure drops below a certain threshold, typically due to temperature changes or a puncture, the light is triggered to alert the driver to check and adjust the tire pressure.

Therefore, the drop in temperature overnight causes a decrease in the average kinetic energy of the air molecules inside the tires, resulting in a decrease in tire pressure, which triggers the low tire pressure warning light.

Hope this helps!

a constant force of magnitude F=45 N and making an angle of 30 to the horizontal is applied on a stationary block placed on the floor over a distance of 8 m. the work done by the force

Answers

The work done by the force on the block is approximately 311.2 Joules.

To calculate the work done by the constant force of magnitude F = 45 N over a distance of 8 m at an angle of 30 degrees to the horizontal, we need to find the component of the force that acts parallel to the displacement.

The horizontal component of the force can be calculated using trigonometry:

F_horizontal = F * cos(angle)

            = 45 N * cos(30 degrees)

            = 45 N * (√3 / 2)

            ≈ 38.9 N

Now, we can calculate the work done by the force using the equation:

Work = Force * Distance * cos(theta)

where theta is the angle between the force and the displacement.

Work = F_horizontal * Distance * cos(0)

     = 38.9 N * 8 m * cos(0)

     = 38.9 N * 8 m

     = 311.2 Joules

For such more questions on force

https://brainly.com/question/26553026

#SPJ8

During the Dust Bowl in the 1930s, there were huge dust storms caused by drought and wind. Farm areas all across the Midwest were affected by erosion. Many farmers lost the crops on which they depended to make a living and support their families.
How can farmers prevent soil erosion on their farms? Choose the two that apply.

A. Leave roots in the soil after harvesting.
B. Plant trees around the fields to block wind.
C. Harvest all the crops on the farm at once.
D. Pull up the entire plant when they harvest crops.

Answers

A. Leave roots in the soil after harvesting
B. Plant trees around the fields to block wind

Batteries are not perfect. They can't deliver infinite current. As the current load on a battery gets larger, the voltage output gets smaller.

a. True
b. False

Answers

True Im typing this for charater limit

answer asap!!! i suck at acceleration

Answers

Answer: 2.67

Explanation: it said he went from 0 to 8 in 3 seconds so if we divide eight By three we get 2.67 rounded to the nearest hundredth so you accelerated that 2.67 m/s

Which expenses do you think will change based on how much you drive

Answers

Increased driving can lead to higher vehicle maintenance and repair expenses, increased fuel costs, potential increases in auto insurance premiums, and additional parking fees, all of which should be considered when estimating the overall impact on your expenses.

The expenses that are likely to change based on how much you drive can be broadly categorized into two main areas: vehicle-related expenses and fuel-related expenses.

1. Vehicle-related expenses: The more you drive, the more wear and tear your vehicle will experience, leading to increased maintenance and repair costs. Regular oil changes, tire replacements, brake pad replacements, and other routine maintenance tasks will be required more frequently.

2. Fuel-related expenses: It's intuitive that the more you drive, the more fuel you'll consume, resulting in higher fuel expenses. Fuel prices can vary, but regardless of fluctuations, increased mileage will directly impact your fuel budget. Fuel-efficient vehicles may mitigate some of these costs, but the overall impact on your expenses will still be noticeable.

For more such questions on driving,click on

https://brainly.com/question/32438244

#SPJ8

Fairly easy question I’ll give extra points help.

Answers

1. third law

2. first law

3. third law

4. second law

yup yup ! answer is above !!!

why entrepreneurs should not be a wild risk taker?​

Answers

Explanation:

Entrepreneurs are not wild risk takers but are instead calculating risk takers. They appear to be risk takers because they see the market differently than the rest of us do. 3. ... Entrepreneurs tend to be optimistic about their chances for success, and usually their optimism is based in reality.

a train has an initial velocity of 30 m/s. If the train accelerates uniformly at a rate of 6.3 m/s ^ for 2.8 seconds what is the trains final velocity?

Answers

T

Answer:

the velocity is a second final to initial velocity of 39

Pls quickly brainliest to the first to anwser

Answers

Answer:

8m/s^2

Explanation:

hope it helps........

Explanation:

you're supposed to know the formula of acceleration which is velocity of a time then you can solve the question

You are watching a s Saturday morning cartoon concerning a jungle hero called George of the Jungle. George attempts to save a friend, an ape named Ape, from a stampeding herd of wildebeests. Ape is at the base of a tall tree which has a vine attached to its top. George is in another tree holding the other end of the vine. George plans to swing down from the tree, grab Ape at the bottom of the swing, and continue up to safety on a ledge which is half of George's initial height in the tree. Assuming that Ape weights the same as George, will they successfully make it to the top of the ledge? If you believe they do, how high a ledge could they make it to? If you disagree, suggest what could be done for George to save Ape.​

Answers

Answer:

I don't think so because if Ape was the same weight as george I don't

think he can hold him but maybe so let's say he could hold his own ape then Yes I think he could make it to the ledge Now I think they could make it to the ledge which was half the size.

Sorry if this sounded weird English is my 2nd language Oh and if this helped please give brainiest thank you <3

Temperature is the measure of the average kinetic energy of the particles in an object. True False

Answers

Answer:

true

Explanation:

with increased temperature particles move faster as they gain kinetic energy

Help me please it’s due right now review question help

Answers

Answer:

M.E = mgh

given, m=400g = 400/1000=0.4kg

h=1.75m

g=9.81m/s²

M.E =0.4×9.81×1.75

=6.867J

Calculate the terminal velocity of
the following nain drops faning
through air (a) one with a diameter
of 0.3cm 6 one with a a diameter
of o. Olm. Take the density of
water to be looo Kym3 and the
eis cosity of air to be ixlos pas.
The buoyancy effect of the air
may be ignored)​

Answers

I’m pretty sure it’s a

A bird is flying directly toward a stationary bird-watcher and emits a frequency of 1490 Hz. The bird-watcher, however, hears a frequency of 1505 Hz. What is the speed of the bird, expressed as a percentage of the speed of sound

Answers

Answer:

The speed of the bird is 1.00% of the speed of sound.

Explanation:

The speed of the bird can be found by using the Doppler equation:

[tex] f = f_{0}(\frac{v - v_{r}}{v - v_{s}}) [/tex]

Where:

v: is the speed of sound = 343 m/s

f₀: is the frequency emitted = 1490 Hz

f: is the frequency observed = 1505 Hz

[tex]v_{r}[/tex]: is the speed of the receiver = 0 (it is stationary)

[tex]v_{s}[/tex]: is the speed of the source =?

The minus sign of [tex]v_{s}[/tex] is because the source is moving towards the receiver.

By solving the above equation for [tex]v_{s}[/tex] we have:

[tex] v_{s} = v - \frac{f_{0}*v}{f} = 343 - \frac{1490*343}{1505} = 3.42 m/s [/tex]

The above speed in terms of the speed of sound is:

[tex]\% v_{s} = \frac{3.42}{343}\times 100 = 1.00 \%[/tex]

Therefore, the speed of the bird is 1.00% of the speed of sound.  

I hope it helps you!

If a current of 1.10 A flows through a 7.00 Ω resistor of length 3.00 m, what is the electric field strength inside the resistor?

Answers

Answer:

the electric field strength inside the resistor is 2.57 V/m

Explanation:

Given;

current flowing through the wire, I = 1.10 A

resistance of the wire, R = 7.00 Ω

length of the wire, L = 3.00 m

The emf created inside the resistor is calculated as;

V = IR

V = 1.10 x 7

V = 7.7 V

The electric field strength inside the resistor is calculated as;

E = V/L

E = 7.7 / 3

E = 2.57 V/m

Therefore, the electric field strength inside the resistor is 2.57 V/m

a disk of a radius 50 cm rotates at a constant rate of 100 rpm. what distance in meters will a point on the outside rim travel during 30 seconds of rotation?​

Answers

50π m ≈ 157 m
Explanation:
100 rev/min (2π rad/rev) / (60 sec/min) = 3⅓π rad/s
d = ωrt = 3⅓π(0.50)(30) = 50π m ≈ 157 m

6) Which of the following describes a good team member?
A) She is willing to compromise.
B) He is aggressive.
C) She is stubborn.
D) He is conceited.

Answers

A she is willing to compromise because she is okay with having to sacrifice what she wants to make it work

Answer: A

Explanation:

Because someone who is aggressive, stubborn, or proud of theirselves are more likely to think they're above everyone else and be a bully. However someone who is willing to compromise is better since you can generally make everyone happy that way

HOPE THIS HELPS ^^

The water pressure to an apartment is increased by the water company. The water enters the apartment through an entrance valve at the front of the apartment. Where will the increase in the static water pressure be greatest when no water is flowing in the system

Answers

Answer:

Option C

Explanation:

Options for the question are as follows -

A. At a faucet close to entrance valve

B. At a faucet away from the entrance valve

C. It will be the same at all faucets

D. There will be no increase in the pressure at the faucets

Solution -

The static force will be the same at all faucets and also the area of the faucets be same.

Thus, the pressure created at all faucets will be the same.

Thus, option C is correct

Other Questions
Find the area of the shaded region. Did the constitution represent everyone in the United States when it was created yes/no why How many excess electrons must be distributed uniformly within the volume of an isolated plastic sphere 30.0 cmcm in diameter to produce an electric field of 1440 N/CN/C just outside the surface of the sphere If 3/4 of a cup of a snack food gives you your daily value of calcium, then what fraction of your daily value of calcium is in 1 cup of the snack food? (Enter a fraction in the form A/B, where A and B are whole numbers. Do not include any words or calculations.) According to the acquired needs theory, which of the following characteristics describe people who have a high need for affiliation? a. Passive and uncritical b. Successfully attain the top levels in the organizational hierarchy c. Tend to enjoy work that is entrepreneurial and innovative d. Successful "integrators" whose job is to coordinate the work of departments Beats wants to build a new factory to produce its headphones. It will cost $230 million initially to build the factory over the course of 12 months, which will be worthless after 10 years. The factory will be depreciated linearly to $0 over 10 years. Beats already owns the land on which the factory will be built. The land is currently worth $10 million and was purchased for $2 million eight years ago.After completion of the factory at the end of year 1, Beats expects earnings before interest and taxes (EBIT) of $39 million each year for 10 years. The company also has to add inventory (components) worth $15 million just before operation starts at the end of the first year.Beat's marginal tax rate is 21% and the appropriate cost of capital for this project is 9%.1. What is the cash flow from assets in year 1 (in $ million)?2. What is the annual depreciation in year 2 (in $ million)?3. What is the cash flow from assets in year 2 (in $ million)?4. What is the cash flow from assets in year 11 (in $ million)?5. What is the NPV of this project (in $ million)? According to the law of supply people buy more of a good when the price increases. people buy more of a good when the price decreases. producers provide more of a good when the price increases. producers provide more of a good when the price decreases. He was a one-term president at this time. Hernandez Company has 350,000 shares of $10 par value common stock outstanding. During the year, Hernandez declared a 10% stock dividend when the market price of the stock was $30 per share. Four months later Hernandez declared a $.50 per share cash dividend. As a result of the dividends declared during the year, retained earnings decreased by:_______.a. $1,242,500. b. $525,000. c. $192,500. d. $175,000. How do you know if a solution is completely saturated 100 POINTS!!What is the value of x? Enter your answer in the box. Con qu frecuencia va a barrer el piso Vctor? The Crusades occurred______A. Mostly before the 14th century B. In 1147C. Mostly before the 11th centuryD. In 1100(Pls help im actually stuck on this) Ben's dad is making a large pot of pasta sauce that calls for 3.5 kilograms of tomatoes. If he triples the amount of tomatoes for the recipe, how many grams of tomatoes will he use? Enter your answer in the box. Evan can do one sit-up every 5 seconds. How many minutes will it take him to do 24 sit-ups ? 4. an electrician is running imc (intermediate metal conduit) and the pipe is resting against the plumbers copper pipe. are these two dissimilar metals allowed to touch each other per the code book? Explain how the ocean floor affects when and how waves break. Explain how the ocean floor affects when and how waves break. Let X be a standard normal random variable. Another random variable is determined as follows. We flip a fair coin (independent from X). In case of Heads, we let Y=X. In case of Tails, we let Y=X.Is Y normal? Justify your answer.yesnonot enough information to determineCompute Cov(X,Y).Cov(X,Y)=Are X and Y independent?yesnonot enough information to determineProblem 3. Problem 1(c)Find P(X+Y0).P(X+Y0)= before buying an existing business you need to identify if the business problems can be fixed.T/F A car drives 68 miles in 1 5/12 hours.What is the average speed in miles per hour