Why does the Z-isomer have less intensity than E

The Hazen-Williams C-factor value is a measure of the smoothness inside a pipe. A higher C-factor indicates that the pipe has less friction loss, meaning that water can flow more easily and smoothly through it.

This does not necessarily indicate that the pipe is more durable or able to withstand higher pressure.
When comparing friction loss in water pipes, a larger Hazen-Williams C-factor value indicates the pipe is:

Hazen-Williams coefficient, abbreviated as C, also called Hazen-Williams friction coefficient, a dimensionless number, is used in the Hazen-Williams Equation. The lower the coefficient, the smoother the pipe is. The higher the coefficient, the less fluid flow is restricted

To know more about Measure  click here .

brainly.com/question/4725561

#SPJ11

The correct answer is C)

Answer - Water will move from the 2M NaCl solution to the pure water compartment. This is because of the process of osmosis, where water moves from an area of high concentration (pure water) to an area of low concentration (2M NaCl solution) to reach equilibrium. The semipermeable membrane allows only water molecules to pass through, and not NaCl ions. Therefore, the concentration of water will increase on the side with pure water, while the concentration of NaCl will remain the same on the other side.

To learn more about Osmosis -

brainly.com/question/31028904

#SPJ11

Obligatory volume can vary depending on factors such as diet, exercise, and overall health, but typically ranges from 500-1000 mL per day.

The obligatory water excretion volume in mL refers to the minimum amount of water that the kidneys must excrete on a daily basis in order to remove waste and maintain electrolyte balance in the body. The amount of water an individual needs to excrete depends on their daily fluid intake, activity level, and health status. Generally, a healthy adult should aim to excrete a minimum of 1.5 liters of urine a day, which is equivalent to 500-1000 mL . If urine output is less than this, it could be a sign of dehydration, which can lead to serious health problems. It is important to monitor urine output and adjust fluid intake accordingly to ensure adequate hydration.

learn more about hydration Refer: https://brainly.com/question/15724859

#SPJ11

We use molecular sieves instead of other drying agents in the alternate method of removing water so that water may pass through the sieve leaving unwanted particles on top, also it can be recycled.

Unlike other drying agents molecular sieves can be recycled several times by heating them at an appropriate temperature. Molecular sieves belongs to the class of desiccants, commonly known as adsorbents. They are used for drying of  hydrocarbon. It is also described as the removal of dissolved water from gases and liquids composed of hydrogen and carbon . Molecular sieves finds its applications in refineries for removal of dissolved water.

To know more about molecular sieves here

https://brainly.com/question/29312346

#SPJ4

Answer:

compound

Explanation:

A business can incorporate all of these options to align with green design principles.

Employees can produce fuel, heat, or power from renewable sources for use inside their workplace. Wind, biomass, geothermal, solar, ocean, hydropower, landfill gas, and municipal solid waste are a few examples of these sources.

The practise of taking into account and limiting environmental effect while producing goods is known as sustainable design or green design. Green design principles provide businesses a variety of opportunities to cut waste, repurpose resources, and recycle goods and materials.

To know more about principles visit:-

https://brainly.com/question/30401997

#SPJ1

In the process of esterification, there are certain IR (infrared) spectral characteristics that can be used to compare the starting materials with the products. One of the most prominent features of the IR spectrum is the carbonyl peak, which is typically found at around 1700 cm-1 for esters.

In the starting materials, this peak will not be present, but it will appear in the IR spectrum of the products, indicating the formation of an ester bond. Another important feature of the IR spectrum that can be used for comparison is the C-O stretch, which is typically found at around 1200-1300 cm-1 for esters. Again, this peak will be absent in the starting materials but will appear in the products.

Other peaks that can be used for comparison include the C-H stretches, which are typically found at around 2800-3000 cm-1 for alkanes, and the O-H stretch, which is typically found at around 3400 cm-1 for carboxylic acids. These peaks will be present in the starting materials but will not appear in the products. Overall, a comparison of the IR spectra of the starting materials and products in esterification can provide valuable information about the formation of ester bonds and the presence or absence of certain functional groups.

To know more about esterification reaction, please click on:

https://brainly.com/question/13963851

#SPJ11

An anticoagulant rodenticide is a type of poison used to control rodents such as rats and mice. It works by preventing the blood from clotting, leading to fatal internal bleeding. An anticoagulant rodenticide is warfarin

Warfarin is a common anticoagulant used in human medicine to prevent blood clots. In rodenticides, it is used in much higher doses to kill rodents. Other anticoagulant rodenticides include bromadiolone, difenacoum, and brodifacoum.

It is important to use these poisons carefully and follow all instructions to prevent accidental poisoning of non-target species such as pets and wildlife. It is also important to properly dispose of any unused poison to prevent it from contaminating the environment.

To learn more about rodenticide

https://brainly.com/question/25121848

#SPJ11

At physiological pH, the carboxylic acid group of an amino acid will be deprotonated, while the amino group will be protonated, yielding the zwitterion form. Your answer: deprotonated, protonated.

At physiological pH, the carboxylic acid group of an amino acid will be deprotonated, while the amino group will be protonated, yielding the zwitterion form.

Amino acids are organic compounds that serve as the building blocks of proteins. They are essential to the structure and function of living organisms, including humans. Amino acids consist of a central carbon atom (alpha-carbon) that is bonded to an amino group (-NH2), a carboxyl group (-COOH), a hydrogen atom, and a variable side chain (R-group).

There are 20 different types of amino acids that are commonly found in proteins. Each type of amino acid has a unique side chain that determines its chemical properties, such as its polarity, charge, and size. The sequence and arrangement of amino acids in a protein determine its three-dimensional structure and its function in the body.

Visit here to learn more about amino acid brainly.com/question/31442968

#SPJ11

The final volume of the balloon in the stratosphere is approximately 3010 L.

To solve this problem, we can use the Combined Gas Law formula which combines Boyle's Law, Charles's Law, and Gay-Lussac's Law. The formula is:
(P1 * V1) / T1 = (P2 * V2) / T2
where P1 and P2 are the initial and final pressures, V1 and V2 are the initial and final volumes, and T1 and T2 are the initial and final temperatures in Kelvin.
First, we need to convert the given temperatures from Celsius to Kelvin:

T1 = 25°C + 273.15 = 298.15 K
T2 = -23°C + 273.15 = 250.15 K
Now, we can plug in the given values and solve for the final volume (V2):
[tex](1.2 atm * 2.50 L) / 298.15 K = (3.00 * 10^{-3} atm * V2) / 250.15 K[/tex]
Next, we need to solve for V2:
[tex]V2 = (1.2 atm * 2.50 L * 250.15 K) / (298.15 K * 3.00 * 10^{-3} atm)[/tex]
V2 ≈ 3010 L

To learn more about gas law click here https://brainly.com/question/27009857

#SPJ11

The concentration of hydrogen ions in the solution rises as a result.

Calculation

To calculate the pH of the solution after the addition of the NaOH solution, we need to use the stoichiometry of the reaction between HCl and NaOH. The reaction's balanced equation is:

HCl + NaOH → NaCl + H2O

According to the equation, one mole of HCl interacts with one mole of NaOH to generate one mole of water and one mole of NaCl. Therefore, we can use the following equation to calculate the concentration of HCl remaining after the addition of the NaOH solution:

moles of HCl = initial moles of HCl - moles of NaOH added

The initial moles of HCl in the 25.00 mL of 0.175 M solution are:

moles of HCl = 0.175 mol/L x 0.02500 L = 0.004375 mol

The moles of NaOH added to the solution are:

moles of NaOH = 0.250 mol/L x 0.01900 L = 0.00475 mol

Therefore, the moles of HCl remaining after the addition of the NaOH solution are:

moles of HCl = 0.004375 mol - 0.00475 mol = -0.000375 mol

This negative value indicates that all of the HCl has been neutralized by the NaOH solution. The excess NaOH will contribute to the final pH of the solution.

To calculate the concentration of NaOH remaining in the solution, we can use the following equation:

moles of NaOH = initial moles of NaOH - moles of HCl added

The initial moles of NaOH in the 19.00 mL of 0.250 M solution are:

moles of NaOH = 0.250 mol/L x 0.01900 L = 0.00475 mol

The moles of HCl added to the solution are as follows:

moles of HCl added = 0.00475 mol

Therefore, the moles of NaOH remaining in the solution are:

moles of NaOH = 0.00475 mol - 0.00475 mol = 0 mol

The total volume of the solution after the addition of the NaOH solution is:

total volume = 25.00 mL + 19.00 mL = 44.00 mL = 0.04400 L

The concentration of the resulting solution is:

concentration = moles of NaCl / total volume

Since the moles of NaCl formed by the reaction are equal to the moles of HCl initially present, we can use the initial moles of HCl to calculate the concentration of the resulting solution:

concentration = 0.004375 mol / 0.04400 L = 0.0994 M

To calculate the pH of the resulting solution, we can use the formula:

pH = -log[H+]

where [H+] denotes the concentration of hydrogen ions in the solution. In this case, the hydrogen ions are formed by the dissociation of water:

H2O → H+ + OH-

The concentration of hydrogen ions in the solution is equal to the concentration of hydroxide ions since the solution is neutral:

[H+] = [OH-] = 1.0 x 10^-14 / [OH-]

Substituting the value of [OH-] from the equation for the dissociation of NaOH in water:

NaOH → Na+ + OH-

[OH-] = moles of NaOH remaining / total volume

[OH-] = 0 mol / 0.04400 L = 0 M

The concentration of hydrogen ions in the solution rises as a result.

For more question on Hydrogen ion

https://brainly.com/question/10217868

As a defense attorney representing a company charged with exceeding the EPA limits on calcium perchlorate discharges, you would want to ask the chemist specific questions to challenge the validity of the test results and potentially have the charges dismissed. Here are three possible questions:

1. What were the quality control measures taken during the EDTA titration process to ensure accuracy and precision of the results?
This question aims to determine if proper procedures were followed during the analysis. The chemist should have taken appropriate measures such as calibration of equipment, replicates, and use of standards to ensure accurate results. Any shortcomings in quality control could cast doubt on the reliability of the test results. 2. Was there any possibility of sample contamination or interference during the collection, transportation, storage, or analysis of the water samples? This question seeks to understand if any external factors may have influenced the test results. The chemist should explain how they ensured that the samples were not contaminated or affected by other substances. Any indication of possible contamination or interference could weaken the case against your client. 3. Can you explain how the EPA determined the specific limit of 20 ppm for calcium perchlorate in groundwater, and provide scientific evidence supporting this limit? By asking this question, you are challenging the basis for the EPA's established limit. The chemist should be able to explain the rationale behind setting the limit at 20 ppm, including any relevant studies or scientific data. If the chemist cannot provide a satisfactory explanation, it may cast doubt on the validity of the limit itself and weaken the case against your client.

For more information on  external factors   see:

https://brainly.com/question/30122182

#SPJ11

The molecular mass of menthol (C10H20O) is 156.30 amu. Option A (156.26 amu) is the closest answer.

To calculate the molecular mass of menthol[tex](C10H20O),[/tex] we need to add up the atomic masses of all the atoms in the molecule.

The atomic masses of carbon (C), hydrogen (H), and oxygen (O) are:

Carbon (C) atomic mass = 12.01 amu

Hydrogen (H) atomic mass = 1.01 amu

Oxygen (O) atomic mass = 16.00 amu

So, the molecular mass of menthol can be calculated as:

Molecular mass of menthol = (10 x carbon atomic mass) + (20 x hydrogen atomic mass) + (1 x oxygen atomic mass)

[tex]scss    = (10 x 12.01 amu) + (20 x 1.01 amu) + (1 x 16.00 amu)     = 120.10 amu + 20.20 amu + 16.00 amu      = 156.30 amu[/tex]

Learn more about mass here:

https://brainly.com/question/30025539

#SPJ11

The driving force for the loss of water in the aldol reaction is the formation of a more stable carbonyl compound through the creation of a new carbon-carbon bond.

An aldol reaction is a powerful tool for forming new carbon-carbon bonds in organic synthesis. The reaction involves the addition of an enolate ion, generated from a carbonyl compound such as an aldehyde or ketone, to the carbonyl group of another aldehyde or ketone.

This results in the formation of a β-hydroxy aldehyde or β-hydroxy ketone intermediate, which can undergo dehydration to yield an α,β-unsaturated aldehyde or ketone product.

Learn more about aldol reaction at

https://brainly.com/question/29857280

#SPJ4

The percent yield of the reaction is approximately 40.3%.

To calculate the percent yield of a reaction, we need to compare the actual yield to the theoretical yield. The theoretical yield is the maximum amount of product that can be formed based on the stoichiometry of the reaction, while the actual yield is the amount of product actually obtained in the experiment.

First, we need to write the balanced equation for the reaction between Na₂S and Cd(NO₃)₂;

Na₂S + Cd(NO₃)₂ → 2NaNO₃ + CdS

From the balanced equation, we can see that 1 mole of Na₂S reacts with 1 mole of Cd(NO₃)₂ to produce 1 mole of CdS and 2 moles of NaNO₃.

Next, we need to calculate the theoretical yield of NaNO₃ based on the given amounts of reactants;

The number of moles of Na₂S is; 8.00 g / 78.04 g/mol = 0.1026 mol

The number of moles of Cd(NO₃)₂ is: 21.65 g / 236.42 g/mol = 0.0916 mol (since Cd(NO₃)₂ has a 1:1 stoichiometry with Na₂S, it is the limiting reactant)

The theoretical yield of NaNO₃ is; 2 mol NaNO₃ / 1 mol Na₂S × 0.1026 mol Na₂S = 0.2052 mol NaNO₃

We can then calculate the actual yield of NaNO₃ based on the given mass;

The actual yield of NaNO₃ is; 14.25 g

Finally, we can calculate the percent yield;

Percent yield = (actual yield/theoretical yield) × 100%

Percent yield = (14.25 g / (0.2052 mol × 84.99 g/mol)) × 100%

Percent yield = 40.3%

Therefore, the percent yield is 40.3%.

To know more about percent yield here

https://brainly.com/question/12704041

#SPJ1

To find the number of F atoms in 5.54 g of F2, we need to use the molar mass and Avogadro's number.
First, determine the moles of F2 in 5.54 g. The molar mass of F2 is approximately 38 g/mol (19 g/mol for each F atom * 2). Approximately 1.76 × 10^23 F atoms in 5.54 g of F2 (Answer E).

Moles of F2 = (5.54 g) / (38 g/mol) = 0.146 moles of F2.

Since each F2 molecule consists of two F atoms, we need to multiply the moles of F2 by 2 to find the moles of F atoms:

Moles of F atoms = (0.146 moles of F2) * 2 = 0.292 moles of F atoms.

Next, use Avogadro's number (6.02 × 10^23 atoms/mol) to convert moles of F atoms to the number of F atoms:

Number of F atoms = (0.292 moles of F atoms) * (6.02 × 10^23 atoms/mol) ≈ 1.76 × 10^23 atoms.

to learn more about Avogadro's number

https://brainly.com/question/859564

#SPJ11

No, a chiral product cannot form from two achiral reactants.

Chirality is a property of a molecule that cannot be superimposed on its mirror image, meaning that it has a non-superimposable mirror image (enantiomer). In order for a molecule to be chiral, it must have a stereocenter, which is an atom that is attached to four different groups.

If both reactants are achiral, then the product they form must also be achiral. This is because the reaction would not have introduced a stereocenter, so the product would not have a non-superimposable mirror image (enantiomer).

However, it is possible for a mixture of enantiomers to form if one or both of the reactants are chiral. In this case, the product would be a racemic mixture of both enantiomers, which is optically inactive because the rotation of one enantiomer cancels out the rotation of the other.

For more question on chiral product click on

https://brainly.com/question/30086472

#SPJ11

The correct answer is (b) Nitrogen.

The Earth's atmosphere is made up of several different gases, including nitrogen, oxygen, argon, carbon dioxide, neon, helium, methane, and others. These gases are held in place by the Earth's gravity, and together they create the air that we breathe.

Nitrogen is the most abundant gas in the atmosphere, making up about 78% of its total volume. Nitrogen is a colorless, odorless, and mostly inert gas, meaning that it does not react with many other substances. It is essential for life on Earth, as it is a key component of amino acids, which are the building blocks of proteins.

Oxygen is the second most abundant gas in the atmosphere, making up about 21% of its total volume. Oxygen is also essential for life, as it is used by many organisms, including humans, to produce energy through respiration.

Argon is a noble gas that is present in the atmosphere in much smaller amounts, making up about 0.9% of its total volume. Argon is also mostly inert, and is used in various applications, such as welding and lighting.

Carbon monoxide, on the other hand, is a toxic gas that is produced by incomplete combustion of fuels. It is present in the atmosphere in much smaller amounts than nitrogen, oxygen, or argon, and can be harmful to humans and other organisms at high concentrations.

Visit to know more about Nitrogen:-

brainly.com/question/1380063

#SPJ11

The purpose of a concrete slump test is to: B. measure the consistency and workability of the mix.

The slump test is a simple and widely used test for measuring the consistency and workability of fresh concrete. It involves filling a standard cone-shaped mold with freshly mixed concrete and then lifting the mold to allow the concrete to slump or settle. The distance that the concrete slumps is measured and used as an indicator of the consistency and workability of the concrete. A higher slump indicates a more workable and flowable mix, while a lower slump indicates a stiffer and less workable mix. The slump test is an important quality control tool for ensuring that the concrete mix meets the desired specifications and is suitable for the intended application.

Learn more about slump test here:

https://brainly.com/question/14837381

#SPJ11

True. Alkynes can be synthesized using acetylide ion, which is formed by deprotonating a terminal alkyne with a strong base.

The acetylide ion can then undergo nucleophilic substitution reactions to form a new alkyne molecule. This method is commonly used in organic chemistry for the synthesis of alkynes.In the first two reactions, the acetylide ion acts as a nucleophile and attacks the electrophilic carbon of the alkyl group, while in the third reaction, it acts as a nucleophile and attacks the electrophilic halide group. The product of the reaction is an alkyne which can be further reacted to yield a variety of substituted alkynes.

learn more about acetylide ion Refer: https://brainly.com/question/30516341

#SPJ11

Explanation:

1, insoluble in water

3, covalent bonding

5, slow reaction rate

7, high activation energies to begin reactions

To calculate the volume that a 0.323 mol sample of gas will occupy at 265K and a pressure of 143 kPa, we can use the ideal gas law equation PV = nRT the volume that a 0.323 mol sample of gas will occupy at 265 K and a pressure of 143 kPa is approximately 0.00491 m³.

The SI unit of pressure is the pascal (Pa), which is defined as one newton of force per square meter of area. Other commonly used units of pressure include atmospheres (atm), pounds per square inch (psi), and kilopascals (kPa).

Pressure plays a fundamental role in many scientific and engineering disciplines, such as physics, chemistry, fluid mechanics, and materials science. It can be used to describe the behavior of gases, liquids, and solids under different conditions, and to understand and design a wide range of devices and systems, from hydraulic systems to airplanes to pressure vessels.

To know more about Pressure visit :

https://brainly.com/question/12971272

#SPJ1

The correct answer is D. All of the given options except for greater economy are advantages of using precast concrete sections.

Precast concrete sections provide better quality control, faster curing, and all-weather construction benefits. Precast concrete sections are manufactured in controlled environments, ensuring consistent quality. They are also cured in ideal conditions, allowing for faster curing times.

Precast concrete sections can be installed in any weather condition, which means that construction projects can continue even during inclement weather. Additionally, using precast concrete sections can save time and money, resulting in greater economy.

To know more about precast concrete, click here:-

https://brainly.com/question/23127906

#SPJ11

If a solid crystal of KHP (potassium hydrogen phthalate) is accidentally pipetted and goes unnoticed throughout titrations, the Ksp value (solubility product constant) would be artificially higher than the true value.

In a titration experiment, the concentration of dissolved KHP is determined by titrating it with a strong base, such as NaOH.

If a solid crystal of KHP is accidentally pipetted, it will eventually dissolve, increasing the concentration of KHP in the solution.

This higher concentration will then require more titrant (NaOH) to reach the endpoint of the titration. As a result, the calculated Ksp value will be higher than the actual Ksp value of KHP, because it will be based on an artificially increased concentration.
In summary, the accidental inclusion of a solid KHP crystal during titration will lead to an overestimation of the Ksp value. To obtain accurate results, it is essential to ensure that no solid crystals are present in the solution before beginning the titration process.

For more information on solubility equilibrium (Ksp) kindly visit to

https://brainly.com/question/13032436

#SPJ11

The iodide ion (I-) causes the smallest crystal field splitting. This is because it is a weaker field ligand compared to hydroxide ion (OH-), dichromate ion (Cr2O7^2-), and chloride ion (Cl-). Weaker field ligands lead to smaller crystal field splitting values.

Crystal field theory (CFT) describes the breaking of orbital degeneracy in transition metal complexes due to the presence of ligands. CFT qualitatively describes the strength of the metal-ligand bonds. Based on the strength of the metal-ligand bonds, the energy of the system is altered. This may lead to a change in magnetic properties as well as color. This theory was developed by Hans Bethe and John Hasbrouck van Vleck.

In Crystal Field Theory, it is assumed that the ions are simple point charges (a simplification). When applied to alkali metal ions containing a symmetric sphere of charge, calculations of bond energies are generally quite successful. The approach taken uses classical potential energy equations that take into account the attractive and repulsive interactions between charged particles (that is, Coulomb's Law interactions).

Visit here to learn more about  Crystal Field Theory : https://brainly.com/question/29389010
#SPJ11

Answer:

Explanation:

True

The nucleophile in the aldol condensation is generated by deprotonation of the alpha-carbon of an aldehyde or ketone by a strong base, forming an enolate ion.

In the aldol condensation reaction, a nucleophile is generated by deprotonation of the alpha-carbon of an aldehyde or ketone by a base, typically a strong base like hydroxide (OH-) or alkoxide (RO-).

This generates an enolate ion, which is a resonance-stabilized anion with a negatively charged oxygen atom and a carbon-carbon double bond adjacent to the carbonyl group.

The general equation for the Aldol condensation reaction is:

RCHO + R'CHO → RCH=CHR' + H2O

The reaction can be catalyzed by a base, such as NaOH, and proceeds via the following mechanism:

Deprotonation: The base (OH-) abstracts a proton from the alpha-carbon of the aldehyde (RCHO) to generate an enolate ion.

RCHO + OH- → RCHO- + H2O

Nucleophilic attack: The enolate ion attacks the carbonyl carbon of a second aldehyde molecule (R'CHO), which is also deprotonated by the base to form its own enolate ion.

RCHO- + R'CHO → RCH=CH-CHO + OH-

Protonation: The resulting beta-hydroxy aldehyde is protonated by water (or acid) to form the aldol product.

RCH=CH-CHO + H2O → RCH(OH)-CH=CHOH

Thus, in the aldol condensation reaction, the enolate ion acts as a nucleophile and attacks the carbonyl carbon of another aldehyde or ketone to form a new carbon-carbon bond and generate a beta-hydroxy aldehyde or beta-hydroxy ketone.

Learn more about the aldol condensation at

https://brainly.com/question/29995098

#SPJ4

There are 0.0456 moles of iron(II) chloride in the original solution. There are still 0.0456 moles of iron(II) chloride in the solution, but the molarity has decreased to 0.1824 M. The final molarity of the iron(II) chloride is 0.1824 M.

The proportion of the solute that is dissolved in a solution is indicated by the solution's concentration. This formula may be used to determine a solution's concentration: Concentration is calculated as Volume of Solute multiplied by 100 and Volume of Solution (ml).

moles = concentration x volume (in liters)

The solution's volume must first be converted from millilitres to litres:

50.0 mL = 50.0/1000 L = 0.0500 L

Now we can calculate the moles of iron(II) chloride:

moles = 0.911 M x 0.0500 L = 0.0456 mol

concentration = moles / volume (in liters)

moles = 0.0456 mol (from part a)

volume = 0.250 L (after adding water)

concentration = 0.0456 mol / 0.250 L = 0.1824 M

To know more about molarity visit:-

https://brainly.com/question/8732513

#SPJ1

The conversion of an epoxide to an alcohol can be achieved by using a strong nucleophile such as water or a hydroxide ion.

To convert an epoxide to an alcohol, you can follow these steps:
1. Choose a suitable nucleophile: For this conversion, you can use a water molecule ([tex]H_2O[/tex]) or another suitable nucleophile as the attacking species. Water is a common choice since it results in the formation of an alcohol.
2. Attack the epoxide: The nucleophile, in this case water, will attack one of the carbon atoms in the three-membered epoxide ring. This attack occurs because epoxides have a strained ring structure, making them highly reactive towards nucleophiles.
3. Ring-opening reaction: As the nucleophile attacks the epoxide carbon, the C-O bond in the epoxide ring breaks, resulting in the ring-opening reaction. This creates an intermediate with the nucleophile attached to the carbon atom.
4. Proton transfer: In the intermediate, there will be a negatively charged oxygen atom. To complete the formation of the alcohol, a proton ([tex]H+[/tex]) needs to be transferred to this oxygen atom. In the case of using water as the nucleophile, another water molecule can act as a proton donor, resulting in the formation of the alcohol and a hydroxide ion ([tex]OH-[/tex]).

To learn more about epoxide click here https://brainly.com/question/26718813

#SPJ11