Which is the communication system uses IoT to monitor smart sensors and output devices to determine when they are about to fail?

To produce the same lift while in ground effect as when out of ground effect, the airplane requires a lower angle of attack. This is because the ground effect reduces the drag on the airplane, allowing it to generate the same amount of lift with a lower angle of attack.

Ground effect is the phenomenon where the air pressure underneath the wings increases when the airplane is close to the ground, reducing the effective angle of attack required to generate lift. This happens because the ground limits the amount of air that can flow around the wings, which results in a decrease in wingtip vortices and an increase in the effective span of the wings. Therefore, since the airplane experiences an increase in lift when in ground effect, it needs a lower angle of attack to produce the same amount of lift as it would need when out of ground effect. In fact, if the pilot maintains the same angle of attack when in ground effect as when out of ground effect, the airplane may actually produce too much lift and become unstable.

Learn more about airplane here-

https://brainly.com/question/17247837

#SPJ11

Where required for the reduction of electric noise for electronic equipment, electrical continuity of metal raceway is not required, and the metal raceway can terminate to a nonmetallic fitting or spacer on the electronic equipment.

Hi! In accordance with NEC 250-96(b), where required for the reduction of electric noise for electronic equipment, electrical continuity of metal raceway is not required, and the metal raceway can terminate to a nonmetallic fitting(s) or spacer on the electronic equipment.

According to NEC 250-96(b), where it is necessary to reduce electric noise for electronic equipment, electrical continuity of metal raceway is not required. In such cases, the metal raceway can terminate to a nonmetallic fitting or spacer on the electronic equipment. This helps to prevent the transfer of electrical noise from the raceway to the equipment, which can interfere with its proper functioning. Nonmetallic fittings or spacers are used because they do not conduct electricity and therefore do not provide a path for the noise to travel.

Learn more about electrical continuity here;

https://brainly.com/question/12791045

#SPJ11

The Square class has a side attribute and perimeter and area methods, an instance of the Square class is created and its perimeter and area are called using the object's methods.

The paragraph describes the specification for a Python class called "Square" which represents a square shape.

It has an attribute named "side" which represents the length of each side. The class has two methods: "perimeter" and "area" which return the perimeter and area of the square, respectively.

An instance of the Square class is created with a parameter specifying the length of the square's side.

The perimeter and area methods are then called on the created object.

Learn more about Square class

brainly.com/question/29796944

#SPJ11

True. In the s-domain, the voltage across a resistor with current i(t) flowing through it can be represented as s times the product of the resistance R and the current i(t), which is equal to sri(s). This is known as the impedance of a resistor in the s-domain.

The Laplace transform takes a continuous time signal and transforms it to the s

-domain.

The Laplace transform is a generalization of the CT Fourier Transform. Let X(s)

be the Laplace transform of x(t)

, then the Fourier transform of x

is found as X(jω)

For most engineers (and many fysicists) the Laplace transform is just a mathematical trick to easily solve a class of partial differential equations. The Laplace transforms a constant coefficient linear differential equation relating the input x(t)

with the output y(t)

into an algebraic polynomial in s

. We will look at this class of constant coefficient linear partial differential equations.

learn more about impedance here:

https://brainly.com/question/30040649

#SPJ11

Hi!

The statement is false.

The voltage across a resistor with current i(t) in the s-domain is given by V(s) = R*I(s), where R is the resistance and I(s) is the Laplace transform of the current i(t).

Learn more about resistance and current: https://brainly.com/question/24858512

#SPJ11

The CAS Latency value of a DIMM memory ad that displays 5-5-5-15 is 5, indicating that the memory module takes 5 clock cycles to respond to a command from the memory controller.

The CAS Latency value of a DIMM memory ad that displays 5-5-5-15 is 5.

CAS Latency (CL) is one of the timings that is specified on a memory module.

It is the time taken by the memory module to respond to a command from the memory controller.

CL is measured in clock cycles, where each cycle is typically 1/2 of the memory clock speed.
The DIMM memory ad that displays 5-5-5-15, the first three numbers (5-5-5) represent the CL value.

The last number (15) represents the time taken by the memory module to complete a full cycle of memory access, called the traps or Row Active Time.

The CL value for this DIMM is 5.
A lower CL value means that the memory module can respond to commands from the memory controller faster, resulting in better performance.

A lower CL value also means that the memory module requires more power to operate, which can increase heat and reduce stability.

For similar questions on value

https://brainly.com/question/29663853

#SPJ11

There are several methods that can be used for strengthening metals. Some of these methods include:

1. Heat Treatment - This involves heating the metal to a specific temperature and then cooling it down quickly to change its microstructure, resulting in increased strength.

2. Cold Working - This involves deforming the metal at room temperature through processes such as rolling, forging, or extrusion, which increases its strength.

3. Alloying - This involves adding other elements to the metal to improve its properties, such as strength, hardness, and corrosion resistance.

4. Surface Hardening - This involves treating the surface of the metal to improve its wear resistance, such as through processes like carburizing, nitriding, or induction hardening.

1. Work hardening: This method involves deforming the metal through processes like bending, rolling, or hammering. The deformation causes an increase in dislocation density, making it harder for the atoms to move, thereby strengthening the metal.

2. Grain refinement: This method focuses on reducing the grain size of the metal. Smaller grains result in a larger total grain boundary area, which restricts the movement of dislocations and enhances the metal's strength. This can be achieved through techniques such as rapid cooling or the addition of certain alloying elements.

3. Solid solution strengthening: This method involves dissolving a secondary element into the primary metal, forming a solid solution. The atoms of the secondary element interfere with the movement of dislocations, increasing the strength of the metal. Common examples include adding carbon to iron to create steel or adding copper to aluminum to create aluminum alloy.

4. Precipitation hardening: Also known as age hardening, this method involves forming fine particles, or precipitates, within the metal matrix. These particles impede the movement of dislocations, enhancing the strength of the metal. This is typically done by heat treating the metal at specific temperatures for a set period of time.

These four methods can help improve the mechanical properties of metals, making them more suitable for a variety of applications.

Learn more about alloying here : brainly.com/question/30432755

#SPJ11

True. CCTV systems can help prevent pilferage by deterring potential thieves and can also detect any attempted or successful thefts.

CCTV (closed-circuit television) systems are commonly used to prevent, deter, and detect pilferage, which is the theft of small items or petty theft. CCTV systems use video cameras to capture footage of the area being monitored, and this footage can be viewed in real-time or recorded for later review. The presence of CCTV cameras can deter potential thieves from committing theft, as they may be afraid of being caught on camera and subsequently identified and prosecuted. If a theft does occur, the footage from the CCTV system can be used to identify the perpetrator and provide evidence for legal proceedings. Additionally, CCTV systems can be used to monitor employees and ensure that they are following proper procedures and not engaging in theft or other illicit activities. Overall, CCTV systems can be an effective tool for preventing and detecting pilferage, as well as providing evidence for prosecution and improving overall security.

Learn more about CCTV here-

https://brainly.com/question/26407408

#SPJ11

Receptacles installed outdoors in a wet location shall have an enclosure that is weatherproof, whether or not the attachment plug cap is installed. This requirement is stated in the National Electrical Code (NEC) section 406.9.

According to section 406.9 of the National Electrical Code (NEC), receptacles installed outdoors in a wet location shall have an enclosure that is weatherproof, whether or not the attachment plug cap is installed. This means that the enclosure must be designed to prevent water from entering the receptacle, even when the plug is not connected to it. This is important because water can cause electrical shocks and create hazards that could lead to injury or damage to electrical equipment. To comply with this code requirement, outdoor receptacles are typically designed with covers that provide a tight seal around the receptacle and the plug when it is inserted. Additionally, the enclosure must be able to withstand exposure to weather and outdoor conditions, such as rain, snow, and extreme temperatures.

Learn more about temperatures here-

https://brainly.com/question/11464844

#SPJ11

The answer to the aforementioned question is True.

True, it is permissible to run unbroken lengths of surface metal raceways through dry walls, partitions, or floors.

This allows for a safe and efficient installation of electrical wiring in various spaces, while maintaining structural integrity and complying with electrical codes.

Learn more about codes at : brainly.com/question/497311

#SPJ11

The use of x ray machine or metal detector to determine whether or not a person is bringing unauthorized items into an area is an example of Entry and Exit Inspection facility access control.

Your question is about the use of an xray machine or metal detector to determine if a person is bringing unauthorized items into an area. This is an example of facility access control known as: c. Entry and Exit Inspection system .

What does a metal detector do?

A metal detector detects metal by creating a magnetic field in it, and the receiver detects that magnetic field while showing its existence. Metal detectors are used in malls, airports, and train stations for screening.

To know more about system click here

brainly.com/question/30146762

#SPJ11

Alternators are devices used to convert mechanical energy into electrical energy. They are widely used in vehicles to recharge the battery and power the electrical systems of the vehicle. Alternators operate based on the principle of electromagnetic induction, which involves the creation of a magnetic field in the rotor to generate electrical energy.

Technician A is correct in stating that a magnetic field is created in the alternator rotor. The rotor is the rotating part of the alternator that contains a series of windings. When an electrical current flows through these windings, a magnetic field is created in the rotor. This magnetic field interacts with the stator, which is a stationary part of the alternator that contains a series of windings, to generate an electrical output.

Technician B is incorrect in stating that alternator output is increased if the speed of the alternator is decreased. The output of an alternator is directly proportional to the speed of the rotor. The faster the rotor spins, the higher the output of the alternator. Therefore, if the speed of the alternator is decreased, the output will also decrease.

In conclusion, both technicians are partially correct, but Technician A is more accurate. A magnetic field is created in the alternator rotor, and the output of the alternator is directly proportional to the speed of the rotor.

Learn more about magnetic field here:

https://brainly.com/question/14848188

#SPJ11

Therefore, the required plastic section modulus for a W12 shape using grade 50 steel is approximately 5.48 in³.

To calculate the required plastic section modulus (Z), we need to know the maximum moment the beam will experience. This can be found using the formula:

Mmax = (wL²)/8

where w is the load per unit length (4 k/ft), L is the span of the beam (25 ft), and ² denotes "squared".

Substituting the given values, we get:

Mmax = (4 k/ft x 25 ft²)/8 = 312.5 k-ft

Now, we can use the formula for the plastic section modulus of a W12 shape, which is:

Z = 2Iy/Fy

where Iy is the moment of inertia about the y-axis and Fy is the yield strength of the steel. For grade 50 steel, Fy is 50 ksi.

The moment of inertia of a W12 shape can be found from reference tables or calculated using software.

Assuming a conservative value of Iy = 137 in⁴, we get:

Z = 2 x 137 in⁴ / 50 ksi

= 5.48 in³

To know more about plastic section modulus,

https://brainly.com/question/31476044

#SPJ11

The formula for figuring a BASE asphalt spread rate is (asphalt weight)/(area covered) = asphalt spread rate.

The base asphalt spread rate formula is used to determine how much asphalt is required to completely cover an area. The asphalt spread rate is calculated by dividing the weight of the asphalt by the area it will cover. Weighing the asphalt on a scale will reveal how much it weighs. By taking measurements of the length and breadth of the area to be paved and multiplying them, the total area in square feet or square metres may be calculated. Common units of measurement for the resulting spread rate are pounds per square yard or kilogrammes per square metre. This formula is important in ensuring that the right amount of asphalt is used to achieve the desired thickness and quality of the pavement.

learn more about asphalt spread rate here:

https://brainly.com/question/31556224

#SPJ11

answer: c. Generic methods.
Generic methods enable programmers to specify, with a single method declaration, a set of related methods.

Generic methods enable programmers to specify, with a single method declaration, a set of related methods. This is because generic methods allow for type parameters to be used in the method declaration, which can then be used to define the types of the arguments and return values for the related methods. This makes the code more flexible and reusable, as the same method declaration can be used with different types of arguments and return values.Generic Method: Generic Java method takes a parameter and returns some value after performing a task. It is exactly like a normal function, however, a generic method has type parameters that are cited by actual type. This allows the generic method to be used in a more general way.

learn more about Generic methods here:
https://brainly.com/question/12995818

#SPJ11

The acknowledgment number in the response segment to the client is determined by the server, while the acknowledgment number in the client's ACK segment is determined by the client.

When a client establishes a TCP session with a server, the server sends a SYN-ACK response segment to the client. This segment contains an acknowledgment number that is determined by the server. The acknowledgment number represents the sequence number of the next byte the server is expecting to receive from the client.
Once the client receives the SYN-ACK segment, it sends an ACK segment back to the server. This ACK segment contains an acknowledgment number that is determined by the client. The acknowledgment number in the ACK segment indicates the next byte the client expects to receive from the server.
In summary, the acknowledgment number in the response segment to the client is determined by the server, while the acknowledgment number in the client's ACK segment is determined by the client.

Learn more about ACK segment here

https://brainly.com/question/15862961

#SPJ11

The connections (attachment) of the grounding electrode conductor to a grounding electrode shall be made in a manner that will ensure a permanent and effective electrical connection.

An electrode is a conductor that is used to establish electrical contact with a non-metallic part of a circuit, such as a semiconductor or an electrolyte. Electrodes are commonly used in many fields, including electronics, electrochemistry, medical devices, and industrial applications.

In electronic devices, electrodes are used to connect electrical circuits to components such as transistors, diodes, and capacitors. In electrochemistry, electrodes are used to initiate and conduct electrochemical reactions, such as in batteries or electroplating.

Different types of electrodes may be used for different applications, including metal electrodes, carbon electrodes, and semiconductor electrodes. Electrodes may also be coated with different materials to enhance their properties, such as platinum or gold to improve conductivity, or to make them more chemically resistant.

Overall, electrodes play a critical role in enabling electrical and electrochemical processes in a wide range of applications.

Learn more about electrode here:

https://brainly.com/question/30529404

#SPJ11

The target asphalt spread rate for non FC-5 mixes is determined based on several factors, including the mix design, desired density, and available equipment.

Here are the steps to determine the target asphalt spread rate:

Determine the mix design: The mix design specifies the proportions of aggregates, asphalt, and other materials needed to produce the desired mix properties. The mix design should be optimized to achieve the desired level of performance and durability.

Determine the desired density: The desired density is typically specified in terms of a percentage of the maximum theoretical density (MTD) for the mix. The MTD is the density that would be achieved if all air voids were eliminated from the mix. The desired density should be selected based on the anticipated traffic volume and the level of compaction that can be achieved with the available equipment.

Determine the available equipment: The asphalt spread rate is affected by the equipment used to place the mix. The equipment should be capable of achieving the desired density without overcompacting the mix, which can cause rutting and other pavement distresses.

Calculate the target asphalt spread rate: Once the mix design, desired density, and available equipment have been determined, the target asphalt spread rate can be calculated. The target asphalt spread rate is typically specified in terms of pounds per square yard (PSY) or kilograms per square meter (KSM) of pavement surface area.

The target asphalt spread rate for non FC-5 mixes can vary depending on the specific mix design, desired density, and equipment used. It is important to carefully consider these factors and select the appropriate asphalt spread rate to achieve the desired pavement performance and durability.

Learn more about asphalt asphalt   here:

https://brainly.com/question/29589497

#SPJ11

The increased mass of the Sun would cause significant changes in the structure of spacetime at the distance of Earth's orbit, affecting the planet's orbit and the passage of time near the Sun.

If the Sun gained mass without changing its radius, the gravitational field around it would become stronger. This would cause the curvature of spacetime to increase, resulting in a deformation of the fabric of space around the Sun.At the distance of Earth's orbit, this increased curvature of spacetime would result in a stronger gravitational force being experienced by the planet. This would cause the planet's orbit to become more elliptical, with a shorter distance between Earth and the Sun at perihelion (the point in the orbit closest to the Sun) and a longer distance at aphelion (the point in the orbit farthest from the Sun).

Learn more about spacetime here:

https://brainly.com/question/14040788

#SPJ11

A non metallic cable shall be secure at intervals not exceeding 4.5 feet and within 12 inches of the box to protect the cable and ensure proper support for electrical connections, as specified in section 334.30 of the National Electrical Code.

The metals loses electrons forming cations while on the other hand, the non-metals gains the electrons forming anions.

Covalent bonding is a type of bonding linking two non-metallic atoms which are distinguished by the sharing of pairs of electrons joining atoms and other covalent bonds. An ionic bond is the force of appeal that holds together positive and negative ions. It forms when atoms of a metallic element loses electrons to atoms of a nonmetallic element. Ionic bonds form only allying metals and nonmetals. When two nonmetals bond, they share pairs of electrons in a covalent bond and both gets stability.

So w can conclude that A covalent bond is formed between two non-metals. The sharing of electron pairs takes place between their atoms and a covalent bond is formed.

Learn more about non metallic here

https://brainly.com/question/29400906

#SPJ11

The correct answer is c. The general current divider equation used to find a branch current is equal to the branch resistance divided by the total resistance, multiplied by the total current. This formula is used when there are multiple resistors in parallel and we want to find the current flowing through a particular branch.

By knowing the branch resistance and the total resistance, we can determine the fraction of the total current that flows through that branch. The total resistance is the sum of all the resistors in parallel, while the branch resistance is the resistance of the particular branch for which we want to calculate the current.
The general current divider equation used to find a branch current is equal to the: c. branch resistance divided by the total resistance, multiplied by the total current.

In this equation, "branch resistance" refers to the resistance of the specific branch you want to find the current for, "total resistance" is the sum of all resistances in the parallel circuit, and "total current" is the current supplied to the entire parallel circuit.

To know more about a particular branch:- https://brainly.com/question/14151495

#SPJ11

The general current divider equation used to find a branch current is equal to option c:

branch resistance divided by the total resistance, multiplied by the total current.

Learn more about branch current: https://brainly.com/question/24858512

#SPJ11

FTP (File Transfer Protocol) is a best-effort, connectionless application layer protocol that is used to transfer files. Transmission Control Protocol/Internet Protocol (TCP/IP) is a set of communication protocols that are used to link network devices on the internet.

A TCP/IP network, such as the internet, uses the File Transfer Protocol (FTP) as a standard network protocol for file transfers between computers.

Network protocol:

A network protocol is a set of guidelines that governs data flow between two or more computing devices when they are connected to a computer network.

It is utilised for controlling files on distant computers as well as for uploading and downloading files. An FTP file transfer protocol client is used to connect to an FTP server in the client-server architecture of FTP. Users can upload, download, delete, or alter files on the remote computer once they are connected.

Learn more about file transfer protocol here

https://brainly.com/question/27581708

#SPJ11

The traffic classification from highest priority to lowest priority would likely be as follows:
1. Audio conference with the sister school in Japan (highest priority)
2. Searching the library database
3. Surfing the web (lowest priority)

In a scenario where network traffic is prioritized with Quality of Service (QoS) on a school network, This prioritization ensures that real-time communication and educational resources receive higher priority, while general web browsing is given the lowest priority.

The reference materials, newspaper and periodical databases, and academic databases that are covered in this chapter are typical examples of library resources.

Dictionaries,  encyclopaedias, atlases, and other library database  specialised resources that offer background knowledge and aid in defining concepts and phrases can be considered reference materials.

Access to articles from a variety of sources, such as newspapers, magazines, and scholarly journals, is made possible via newspaper and periodical databases. These databases frequently enable users to conduct subject, author, or keyword searches for articles.

On the other hand  academic databas concentrate solely on intellectual research and frequently contain peer-reviewed articles, conference papers, and dissertations. In-depth coverage of academic research in a given field is provided by these databases, which typically cover a limited range of topics than newspaper and periodical databases.

Learn more about library database here

https://brainly.com/question/31181615

#SPJ11

The National Electric Code (NEC) states that a run of electrical metallic tubing between outlet boxes shall not exceed 3 feet close to the box.

This is to ensure safe and efficient electrical wiring installation. It is important to follow these guidelines to prevent electrical hazards and ensure compliance with local building codes. If too many wires are installed in a conduit, the conduit can become overheated, which could create a fire hazard. The maximum length limit helps ensure that there is adequate space in the conduit for the wires, which in turn helps prevent overheating.It's worth noting that the maximum wire fill rule for EMT conduit is not the only requirement for conduit installations in the NEC. Other requirements include rules for minimum conduit size, maximum conduit fill, and proper installation techniques to ensure the conduit is securely fastened and protected from damage. These requirements are all aimed at ensuring the safety and reliability of electrical wiring installations.

Learn more about electrical here

https://brainly.in/question/47308007

#SPJ11

The statement you provided is: "Connections from cellular concrete floor raceway headers to cabinets shall be made by means of listed metal raceways or PVC raceways." Based on this information, the statement is True.

Cement, water, coarse aggregates, fine aggregates (i.e. sand), and air are the five essential ingredients that make up a concrete mix, which can be combined in different ratios.

To give the mixture the attributes you want, you can add cellular concrete more ingredients such pozzolanic minerals and chemical admixtures.

Concrete is created with the aid of cement, sand, gravel, and water.

These ingredients should be combined in the following ratios: 1:2:3:0.5 to achieve maximum power. Those proportions are one part cement, two parts sand, three parts gravel, and one and a half parts water.

Learn more about  cellular concrete here

https://brainly.com/question/31545285

#SPJ11

Shale is the primary source rock for the vast majority of the world's oil and natural gas reserves.

A typical source rock of oil, which started out as mud in which dead organic matter settled, is shale. Shale is a sedimentary rock that is formed from the accumulation of clay and other fine-grained sedimentary particles. Over time, the accumulation of dead organic matter, such as plankton and algae, is buried by the sedimentary layers and undergoes a process of heat and pressure called diagenesis, which eventually transforms the organic matter into hydrocarbons such as oil and natural gas.

Learn more about rock here:

https://brainly.com/question/17137899

#SPJ11

the major high-speed network experimenting with long distance Ethernet over fiber is e. the National Lambda Rail.

NLR uses fiber-optic lines, and is the first transcontinental 10 Gigabit Ethernet network. Its high capacity (up to 1.6 Tbit/s aggregate), high bitrate (40 Gbit/s implemented; planning for 100 Gbit/s underway and high availability (99.99% or more), enable National LambdaRail to support demanding research projects. Users include NASA, the National Oceanic and Atmospheric Administration, Oak Ridge National Laboratory, and over 280 research universities and other laboratories. In 2009 National LambdaRail was selected to provide wide-area networking for U.S. laboratories participating in research related to the Large Hadron Collider project, based near Geneva, Switzerland.

It is primarily oriented to aid terascale computing efforts and to be used as a network testbed for experimentation with large-scale networks. National LambdaRail is a university-based and -owned initiative, in contrast with the Abilene Network and Internet2, which are university-corporate sponsorships. National LambdaRail does not impose any acceptable use policies on its users, in contrast to commercial networks. This gives researchers more control to use the network for these research projects. National LambdaRail also supports a production layer on its infrastructure.

learn more about Ethernet here:

https://brainly.com/question/14622272

#SPJ11

Memberwise assignment refers to the process of copying the individual elements (or members) of one data structure to another, while maintaining their respective order and positions. This type of assignment is often used in data structures like arrays, structs, and classes.

Here's a step-by-step explanation of memberwise assignment:

1. Identify the source and target data structures.
2. Ensure that the data structures have the same type and size.
3. Iterate through each element in the source data structure.
4. For each element, assign the value from the source to the corresponding position in the target data structure.
5. Continue until all elements have been copied.

In short , memberwise assignment is a way to transfer the contents of one data structure to another, ensuring that all individual elements are copied and their order is preserved.

Learn more about data structure here :

brainly.com/question/13147796

#SPJ11

According to the National Electrical Code (NEC) 344-10(B)(1), rigid metal conduit is allowed to be installed in concrete, in direct contact with the earth, or in areas subject to severe corrosive influences. When installed in concrete or in direct contact with the earth, it is protected from physical damage and provides a reliable grounding path. However, in areas with corrosive influences, the rigid metal conduit may be subject to degradation and require additional protection.

In summary, rigid metal conduit can be installed in concrete or in direct contact with the earth, and in areas subject to severe corrosive influences, it must be protected with appropriate measures that are judged suitable for the condition.

Learn more about concrete here: brainly.com/question/28903866

#SPJ11

The default copy constructor of a class performs a shallow copy of all the data members of the class. This means that the copied object will have the same values for its data members as the original object.

However, if the data members of the original object are pointers to dynamically allocated memory, the copied object will have a copy of the pointers but not a copy of the memory they point to. This can lead to problems if the copied object and the original object both try to modify the same dynamically allocated memory.

The default copy constructor performs a shallow copy of the object's data members. It simply copies the values of all data members from the original object to the new object. However, there are some cases where a class may require a custom copy constructor to perform a deep copy of its data members. In such cases, the default copy constructor may not be sufficient.

For instance, if a class has a pointer as a data member, then a shallow copy of the pointer value will simply copy the address of the pointer rather than the value it points to. This may lead to unexpected behavior when the original object and the copied object modify the same data. In summary, the default copy constructor is a member function of a class that is automatically generated by the compiler if the class does not have its own copy constructor defined.

Learn more about  copy constructor here

https://brainly.com/question/31565873

#SPJ11