The type of wrench that surrounds and grips all corners when loosening and tightening bolts and nuts is known as box-ends.
What are wrenches used for?Wrenches are significantly used for loosening and tightening of fasteners. These are typically a kind of tool that is used to provide grip and mechanical advantage in applying torque to turn objects—usually rotary fasteners, such as nuts and bolts—or keep them from turning.
According to the context of this question, there are basically two major kinds of wrenches: Pipe wrenches used in plumbing for gripping round (cylindrical) things. General-use wrenches are used on nuts and bolts that have flat, parallel surfaces; e.g., square or hexagonal (hex).
Therefore, box-ends are a type of wrench that surrounds and grips all corners when loosening and tightening bolts and nuts.
To learn more about Technological tools, refer to the link:
https://brainly.com/question/25860017
#SPJ1
Suppose ArrayList X contains two strings[Beijing, Singapore]. Which of the following method will causeruntime errors? (Select all that apply)
A) x.size()
B)x.set(2, "New York");
C) x.remove(2)
D) x.get(2)
E)x.get(1)
With the assumption that ' ArrayList X ' contains two strings [Beijing, Singapore], the methods that will cause runtime errors are (B) x.set(2, "New York"); (C) x.remove(2), and (D) x.get(2).
A runtime error is an error that is encountered during the program execution at runtime. A runtime error raises when a program is syntactically correct but has an issue that is only detected during program execution.
Based on the given runtime errors, it is said to be true that these errors are correct in the context of the syntax of the programming language but these are performing such operatons that are not aligned to the given array named ArrayList X. So as a result during program execution, the compiler generates runtime error.
You can learn more about runtime error at
https://brainly.com/question/14727652
#SPJ4
The ____________ of a fluid power machine is used to stop and start the operation, extend and retract actuators, and sense and guide actuator motion. (Page 5)A.Control SystemB.Power DiagramC.SequenceD.Human Operator
The cylinder, motor, or rotary actuator of a fluid power device is supplied with pressurized fluid by a pump.
What are fluid power systems used for?The cylinder, motor, or rotary actuator of a fluid power device is supplied with pressurized fluid by a pump. Variable flow rates from the pump or through valves inside the fluid power circuit are used to control output speed and direction.
are utilized in a range of applications, including heavy machinery, robotics, and automotive braking systems. Using either hydraulic or pneumatic cylinders, these devices generate linear motion.
When compared to other conventional power-transmission methods, fluid power has the highest power density. Fluid power systems can be divided into two categories: pneumatic and hydraulic. Pneumatic systems employ neutral gases like air, whereas hydraulic systems use liquids like water and oil.
Therefore, the correct answer is option a) Control System.
To learn more about fluid power refer to:
https://brainly.com/question/22590501
#SPJ4
technician a says virtual fuses, or e-fuses, are a recent innovation in circuit protection. technician b says virtual fuses are software-controlled fuses that use field effect transistors (fet) as the circuit control device. who is correct?
The prospect for the development of a software-based virtual fuse has been made possible by the growing usage of power field-effect transistors rather than power relays to manage electrical loads on automobiles. The vehicle OEM will benefit greatly from this advancement in a number of ways. Along with the cost of the fuse, further savings will also be made.
What role does a fuse play in electrical safety?A fuse has a thin metal strip inside it that acts as a current path. if the circuit is receiving a significant quantity of current.
What is the fundamental idea behind a Mcq fuse?An electric fuse is primarily used to guard against overcurrent, short circuits, and improperly matched loads on electrical equipment.
To know more about software-controlled fuses visit :-
https://brainly.com/question/1851832
#SPJ1
Flashing green lights that are not traffic signals are sometimes used to warn you of an upcoming stop sign, railroad crossing, an upcoming signal light, pedestrian crossing, school zone, or construction zone.
false
False, There are instances when flashing green lights other than traffic signals are employed to alert drivers of impending stop signs, railroad crossings, signal lights, pedestrian crossings, school zones,
Robots are signalling devices used at road junctions, pedestrian crossings, and other sites to manage traffic flows. Traffic lights, traffic signals, or stoplights are also known as these terms in South Africa.
Traffic lights typically include three signals, which convey important information to cars and cyclists through the use of colours and symbols like arrows and bicycles. The standard traffic light colours are vertically or horizontally organised red, yellow, and green. Although this is a worldwide standard, there are differences in traffic signal legislation and sequences on a national and municipal level.
To lessen the need for police personnel to regulate traffic, the technique was initially used in December 1868 on Parliament Square in London.
Electricity and computerised control have enhanced traffic light technology since then.
Learn more about Lights here:
https://brainly.com/question/14284019
#SPJ4
question 1 a design team completes their high-fidelity prototype of a responsive website. before they hand off designs to the engineering team, they need to confirm that the designs are final. what questions should they answer before handing off the designs? select all that apply.
The correct answer is A back-end developer writes code that forms the backbone of a website or app.
The project name and version should be included in a file name. No. The date, the author, and the version number must all appear in a file's name. High-fidelity mockups let designers make several changes without compromising the functioning of the design. Recall that you must enter prototype mode by selecting it from the menu in the top-left corner in order to construct a prototype. I'll first arrange my mockups according to the major user flow. In other words, I want my mockups to show the website of the library in the order that people would navigate it. Due of the various connections between the material, a matrix structure enables visitors to choose their own path. The concepts of hypertext, or HTML, are fully utilised by this style of structure.
To learn more about back-end developer click the link below:
brainly.com/question/12957736
#SPJ4
How many times will the print statement execute? for i in range(1, 3): for j in range(8, 12, 2): print(f{i}. {i}') O a. 9 Ob.4 O c. 6 O d. 36
Answer:
Option2 4
Explanation:
a series could be an arithmetic progression or geometric progression or fibonacci series.you will be provided with N numbers. you task is to identify which series it is, and find the next number in that series.
Answer:
import java.util.*;
class fibonacci
{
public static void main(String args[])
{
Scanner scanner = new Scanner(System.in);
int n1=0,n2=1,n3,i,count;
count = scanner.nextInt();
System.out.print(n1+" "+n2);//printing 0 and 1
for(i=2;i<count;++i)
{
n3=n1+n2;
System.out.print(" "+n3);
n1=n2;
n2=n3;
}
}
}
Explanation:
True/false: A method that may throw a checked exception must either catch that exception or declare that it throws an exception in its header.
The statement " A method that may throw a checked exception must either catch that exception or declare that it throws an exception in its header" is False.
What is an exception?
An exception is a circumstance that takes place while a program is running that prevents the instructions from running as intended. A method produces an object and passes it to the runtime system when an error occurs within the method. The ability to decouple a program's basic logic from the specifics of what to do when something unusual occurs is made possible by exceptions. In conventional programming, error reporting, exception handling, and detection frequently result in muddled spaghetti code.
To learn more about an exception, use the link given
https://brainly.com/question/19511267
#SPJ4
A certain half-reaction has a standard reduction potential Ered=-0.64 V. An engineer proposes using this half-reaction at the anode of a galvanic cell that must provide at least 0.90 V of electrical power. The cell will operate under standard conditions. Note for advanced students: assume the engineer requires this half-reaction to happen at the anode of the cell. ローロ Op Is there a minimum standard reduction potential that the half-reaction used at yes, there is a minimum. the cathode of this cell can have?
The minimum standard reduction potential of the cathode is -0.64V. The cathode has no maximum standard reduction potential.
O₂(g) + 4 H⁺(aq) + 4 e⁻ ⇒ 2 H₂O(l)
The difference between the cathode's reduction potential (E°red, cat) and the anode's reduction potential (E°red, an) is known as the standard cell potential (E°).
E° = E°red, cat - E°red, an
If E°red, an = -0.64 V and E° = 0.90V,
E°red, cat = E° + E°red, an = 0.90V --0.64V = 0.26V
The cathode's standard reduction potential is -0.64V at the very least. The cathode has no maximum standard reduction potential.
The O2/H2O cathode, with a reduction potential of E°red = -0.64V, is a potential cathode. The cathode would experience the following reduction:
O₂(g) + 4 H⁺(aq) + 4 e⁻ ⇒ 2 H₂O(l)
Learn more about reduction potential here
https://brainly.com/question/20040177
#SPJ4
Which of the following statements about the fatal Tesla accident involving Joshua Brown is not true? A) The "autopilot" feature was engaged. B) The Tesla was speeding. C) Foggy conditions made visibility poor. D) Brown did not have his hands on the steering wheel. E) Autopilot's radar mistook the tractor trailer for an overhead sign.
The correct answer is C) Foggy conditions made visibility poor. statements about the fatal Tesla accident involving Joshua Brown is not true.
Fog reduces sight to one kilometre, making it impossible for you to see farther than that from where you are now standing. One to two kilometres of sight may be lost due to mist. Fog comes in a variety of forms, including freezing fog, valley fog, advection fog, and radiation fog. The small water droplets hanging in the air are to blame for the decreased visibility. In urban and industrial locations, where there are lots of pollution particles functioning as water droplet nuclei, the fog tends to be the thickest. Although fog may cause precipitation (drizzle), precipitation (drizzle) is not the same thing as fog. Fog, by definition, occurs when visibility is less than one kilometre, says the international definition (0.62 mile).
To learn more about Tesla click the link below:
brainly.com/question/23838761
#SPJ4
Masonry veneer curtain walls:
a) are supported from below.
b) are hung from above.
c) have weep holes at the shelf angles.
d) do not need wall ties.
e) a and c.
f) b and d.
Curtain wall typically fastens to the exterior of the floor slabs, acting as a "curtain" that is actually draped on the building and is not load bearing.
What are the types of curtain walls?Masonry veneer walls are composed of a single, exterior, non-structural layer that is commonly built of brick, stone, or artificial stone. The term "anchored veneer" refers to masonry veneer that may have an air space underneath it. Adhered veneer is masonry that has been adhered directly to the backing.
Although it is connected to the building structure, the framing is not responsible for supporting the building's floor or roof loads.
In general, stick curtain wall and unitized curtain wall are the two primary types of curtain wall systems. Although they share a similar look, the two are produced in distinct ways and are better suited to particular projects.
Curtain wall typically fastens to the exterior of the floor slabs, acting as a "curtain" that is actually draped on the building and is not load bearing. Systems are most frequently built in and span from slab to slab.
Therefore the correct answer is option e) a and c.
To learn more about Masonry veneer refer to:
https://brainly.com/question/4506535
#SPJ4
the mac group does not replace the primary functions of eocs or other dispatch organizations.truefalse
True, the mac group does not replace the primary functions of eocs or other dispatch organizations
Multi-agency Coordination Group is the name given to the group. It is also referred to as a policy group on occasion. Its members are agency executives, designees, or administrators who are in charge of serving as a policy-level body by facilitating decision-making among all of these members, particularly those who are affiliated with the stakeholder organization or agencies that are affected by the resources data used during the incident. The multi-agency coordination group may also be represented by non-governmental groups like corporations or volunteer organizations. The national incident management system off-site structure includes this group. Below is a list of this group's main responsibilities: supporting the distribution of resources and setting of priorities. Making a corporative choice because this group includes several agencies. allowing the appointed or elected officials to make a decision. In general, incident management falls within the purview of the incident commander. The principal duty of the EOC, dispatch organizations, coordination, or other operations are not replaced by this group.
Learn more about mac group here
https://brainly.com/question/25270075
#SPJ4
Problem 1: For each of the following integrals, specify the values of the real parameter o which ensure that the integral converges. Your expression for o should be in the form of an inequality. dt (a) je seloojazd tent 0 (b) Sete-(0-jwt dt o (c) Seste-lonjw)t dt (a) Je * -(0-ja)i dt
Expression for σ should be in the form of an inequality as:
(a) σ > -5
(b) σ < -5
(c) σ ∈ R
(d) Here, integral doesn't converges for any value of σ.
What is integral?In mathematics, an integral allocate numbers to functions in a way that defines displacement, area, volume, and other concepts that result from the combination of infinitesimally small data. Integration describes the procedure for locating integrals.
One of the basic, essential operations of calculus is integration, which, along with differentiation, is used to solve issues in mathematics and physics involving, among other things, the volume of a solid, the length of a curve, and the area of an arbitrary shape.
The integrals listed here are what are known as definite integrals, which are defined as the signed area of the region in the plane that is bound by the graph of a particular function between two points on the real line.
Learn more about integrals
https://brainly.com/question/27419605
#SPJ4
consider an integer array, nums, which has been declared and initialized with one or more integer values. which of the following code segments updates nums so that each element contains the square of its original value?
The correct answer is int k = 0; while (k <nums. length) nunstk) - nuns [k] nuns [k]; II. an integer array, nums, which has been declared and initialized with one or more integer values.
Integer baz [5] = ; By doing this, an array of five int values is created, each initialised to zero: However, when an array is defined, its elements can be explicitly initialised to certain values by surrounding those initial values in brackets. An array is a group of related data pieces kept in close proximity to one another in memory. The sole way to retrieve each data piece directly is by using its index number, making it the most basic data structure. The array is given a name and the members' types are described in a "array declaration." It may also provide the array's element count. A pointer to the type of the array items is regarded to be a variable of array type.
To learn more about integer click the link below:
brainly.com/question/15276410
#SPJ4
A flexible pavement is constructed with 4 in. (10.16 cm) of hot mix asphalt wearing surface, 8
in. (20.32 cm) of emulsion/aggregate-bituminous base, and 8 in. (20.32 cm) of crushed stone
subbase. The subgrade has a soil resilient modulus of 10,000 psi (68.95 MPa), and M 2 and M 3
are equal to 1.0 for the materials in the pavement structure. The overall standard deviation is
0.5, the initial PSI is 4.5, and the TSI is 2.5. The daily traffic has 1080 20-kip (89.0-kN) single
axles, 400 24-kip (106.8-kN) single axles, and 680 40-kip (177.9-kN) tandem axles. How many
years would you estimate this pavement would last (i.e., how long before its PSI drops below a
TSI of 2.5) if you wanted to be 99% confident that your estimate was not too high, and if you
wanted to be 95% confident that your estimate was not too high?
the type of counter where each flip-flop provides the clk input to the next flip-flop is referred to as a counter
Asynchronous Counter is a type of counter in which each flip-flop provides the clk input to the next flip-flop.
What is a Asynchronous Counter?
Asynchronous counters have had an output that really is independent of the clock signal. Because the flip flops in asynchronous counters are fed with different clock signals, output may be delayed.
The number of logic gates required to design asynchronous counters is very small. As a result, their design is straightforward. Asynchronous counters is also termed as the ripple counters.
The number of flip flops used in a ripple counter is determined by the number of counter states (ex: Mod 4, Mod 2 etc). The number of counter output states is referred to as the "Modulus" or "MOD" of the counter. A counter can have a maximum of 2n states, where n represents the number of flip flops used in the counter.
To know more about Asynchronous Counter, visit: https://brainly.com/question/29649160
#SPJ4
Why is there almost no wind at the equator and at 30 degrees north latitude, but a dependable northeasterly wind in between?
There is almost no wind at the equator and at 30 degrees north latitude, but a dependable northeasterly wind in between because the two hemispheres have opposite rotations.
What is latitude?
The north-south location of a point on the surface of the Earth or another celestial body is indicated by the latitude coordinate in geography. Latitude is expressed as an angle with a range of -90° at the south pole, 90° at the north pole, and 0° at the equator. The latitude scale counts the miles north or south of the equator. The imaginary lines that divide the Earth are known as parallels or lines of latitude.
Although they run east to west, they gauge your distance in either the north or south. Longitudes and latitudes are similar in that they are both measured in degrees, minutes, and seconds, where one degree equals 60 minutes and one minute equals 60 seconds.
To learn more about latitude, use the link given
https://brainly.com/question/14674354
#SPJ4
by how many microseconds is the load voltage out of phase with the source voltage? express your answer in microseconds to three significant figures. view available hint(s)
The voltage function v ( t ) is initially expressed in terms of sine, while the current function I ( t ) is initially expressed.
Phase shift is the term used to describe the different positions of two sinusoidal waveforms at a specific time moment. By determining the relationship between the current and voltage waveforms of the specific circuit, the phase shift is utilized to assess the functions of the circuit.
One millionth of a second is equal to one microsecond in the International function of Units. When Unicode is unavailable, we may be given a reduced version of its symbol, which is s. One thousandth of a millisecond, or 1000 nanoseconds, is a microsecond.
A microsecond is one millionth (10 -6) of a second (us or Greek letter mu plus s). As a point of reference, a millisecond (ms or msec) is one thousandth of a second and is frequently used to gauge how quickly data is read from or written to a hard drive, a CD-ROM player, or transferred over the Internet.
Know more about hard drive here:
https://brainly.com/question/10677358
#SPJ4
Build a class called BankAccount that manages checking and savings accounts. The class has three attributes: a customer name, the customer's savings account balance, and the customer's checking account balance.
Implement the following constructor and instance methods as listed below:
Constructor with parameters (self, new_name, checking_balance, savings_balance) - set the customer name to parameter new_name, set the checking account balance to parameter checking_balance, and set the savings account balance to parameter savings_balance.
deposit_checking(self, amount) - add parameter amount to the checking account balance (only if positive)
deposit_savings(self, amount) - add parameter amount to the savings account balance (only if positive)
withdraw_checking(self, amount) - subtract parameter amount from the checking account balance (only if positive)
withdraw_savings(self, amount) - subtract parameter amount from the savings account balance (only if positive)
transfer_to_savings(self, amount) - subtract parameter amount from the checking account balance and add to the savings account balance (only if positive)
The Java code that follows builds the BankAccount class with each of the required constructors, getter and setter methods, withdraw methods, and even the transferToSavings function.
bank account class
customerName is a private string.
personal checking and savings balances;
publicly accessible BankAccount(String newName, Double amt1, Double amt2)
newName = this.customerName;
checkingsBalance = amt1 in this;
savingsBalance.this = amt2;
}
getCustomerName() for public strings
bring back clientName;
}
setCustomerName(String customerName) in public void
customerName is the value of this.
}
getSavingsBalance() for public double
savingsBalance return;
}
setSavingsBalance(double savingsBalance), public void
savesBalance = this.savingsBalance;
}
getCheckingsBalance() for public double
a checkingsBalance response;
}
setCheckingsBalance(double checkingsBalance) is a public void function.
checkingsBalance is equal to this.
}
void depositChecking(double amt) in public
if (amt > 0) {
amt + this.checkingsBalance;
}}
depositSavings(double amt) public void
if (amt > 0) {
savingsBalance.this += amt;
}}
withdrawChecking(double amt), public void
if (amt > 0) {
checkingsBalance.this = amt;
}}
withdrawSavings(double amt), public void
if (amt > 0) {
savingsBalance.this -= amt;
}}
transferToSavings(double amt), public void
if (amt > 0) {
checkingsBalance.this = amt;
savingsBalance.this += amt;
}}}
Know more about string:
https://brainly.com/question/13262184
#SPJ4
construct a small-signal model. ignore channel length modulation for m1, m2, and m3. consider only cgd. (5pt) (b) find the small-signal gain without considering cgd in part
The ratio of the input voltage to the output voltage is known as the small signal voltage gain (Av): The tiny signal output current, io in the collector or drain, is equal to the input voltage V in (vbe for the BJT and vgs for the MOS) multiplied by the transconductance g m.
At each step of the VGS increase, record the drain current (ID). Divide the slight changes in the current ID by the small changes in VGS to obtain the transconductance (gm). A tiny signal is an AC signal that is overlaid on a bias signal (more precisely, a signal with zero average value) (or superimposed on a DC constant signal). This splitting of a signal into two halves enables the use of superposition to streamline subsequent analysis.This transconductance connects the output current to the transistor gain represented by the input voltage. Therefore, with a constant value of VDS, the formula for the slope of the transconductance curve is given as gm = ID/VGS.
To learn more about voltage click the link below:
brainly.com/question/29445057
#SPJ4
suppose rashard and alyssa are playing a game that requires both to simultaneously choose an action: up or down. the payoff matrix that follows shows the earnings of each person as a function of both of their choices. for example, the upper-right cell shows that if rashard chooses up and alyssa chooses down, rashard will receive a payoff of 6 and alyssa will receive a payoff of 7. alyssa up down rashard up 4, 4 6, 7 down 2, 4 5, 1: The only dominant strategy in this game is for _____ to choose_____. (left, right)The outcome reflecting the unique Nash equilibrium in this game is as follows: Larry chooses _____ and Megan chooses _____
The only dominant strategy in this game is for Alyssa to choose left The outcome reflecting the unique Nash equilibrium in this game is as follows: Larry chooses right and Megan chooses Left
What does "dominant strategy" mean?In game theory, the phrase "dominant strategy" refers to the choice that is best for a player regardless of the actions taken by their opponents, whereas the phrase "inferior strategy" designates the alternative.
Since Megan selecting "Left" is the sole effective technique in this game. It implies that she will always adopt a "left" tactic, regardless of Larry's decision.
Therefore, the result of the game, which reflects the particular Nash equilibrium, is as follows: Megan picks "Left," whereas Larry chooses "Right". One-of-a-kind Nash equilibrium is (Right, Left).
Learn more about dominant strategy from
https://brainly.com/question/14056827
#SPJ1
Steady-state creep data takenfor an iron at a stress level of 140 MPa (20,000 psi) are givenhere:
es T(K)
6.6*10-4 1090
8.8*10-2 1200
If it is known that the valueof the stress exponent n for this alloy is 8.5, compute thesteady-state creep rate at 1300 K and a stress level of 83 MPa(12,000 psi).
The steady-state creep rate at 1300 K and a stress level of 83 MPa(12,000 psi) is 1.77 × 10⁻⁵.
What is creep rate?Temperature-dependent time rate of material deformation under stress. It is the slope of the creep test's time-versus-creep diagram. The most common units are in/in/hr or % of elongation/hr. The slope of the portion of the creep vs. time diagram corresponding to secondary creep is known as the minimum creep rate.
Creep is the propensity of a solid material to move slowly or undergo permanent deformation when subjected to ongoing mechanical stresses. Long-term exposure to high stress levels that are still below the material's yield strength can lead to it. In materials heated for an extended period of time, creep is more severe and typically gets worse as the material gets closer to melting.
Learn more about creep rate
https://brainly.com/question/14042064
#SPJ4
Boulders, building trusses, and lead ingots would not make good mediums of exchange because they lack the key characteristic of:
The correct answer is portability Boulders, building trusses, and lead ingots would not make good mediums of exchange because they lack the key characteristic
Trade credit is credit that the seller extends to the buyer. Any authorised form of payment for goods and services is money. Money should have two crucial qualities: durability and simplicity. A time deposit is another name for a checking account. Everyday life involves the usage of money. We work hard for money, spend it, and rarely give it any thought. Money is any good that is frequently used as the final payment for goods and services, according to economists. A medium of trade need to be trustworthy, transportable, interchangeable, and have a constant inherent value.
To learn more about portability click the link below:
brainly.com/question/13748255
#SPJ4
1.a (3 points) compute the value of capacitor voltage vc if the switch is in the down position (2) for a long time. measure vc and compare to your computed value. how long is "a long time" for this circuit? 1.b (2 points) compute the value of vc if the switch is in the up position (1) for a long time. use the measured value of the battery voltage. measure vc and compare.
As a result, in this case, the capacitor voltage is 5.68 volts after one second. There are 7.78 volts after two seconds. It is 8.55 volts after 3 seconds. It is 8.83 volts after 4 seconds, and 8.94 volts after 5 seconds.
The capacitor's starting voltage is zero. The voltage across the capacitor = V = Q/C = 0 and the capacitor's charge Q are both zero before the switch is closed. The capacitor's charge has not had time to accumulate when the switch is closed, therefore the charge and voltage are still 0. This means that connecting two, three, four, or more 1.5 volt batteries in series will result in 1.5 volts of voltage! Individual electrons can only travel through one of the alternatives in a parallel circuit.
Learn more about voltage here-
https://brainly.com/question/29342143
#SPJ4
Obtain The Deflection At The Mid-PointA horizontal beam is supported by a rigid pin at AA and a rod at CC. Both beam and rod are made of the same material, with elasticity modulus E=215 GPaE=215 GPa. The beam has moment of inertia I=58×106 mm4I=58×106 mm4 and the rod has cross-sectional area A=203 mm2A=203 mm2. Assume P=3 kNP=3 kN L=7 mL=7 m, and H=4 mH=4 m.By superposing the deflection of a simply supported beam and the deflection that a "rigid" beam would experience due to the stretching of the rod, determine the magnitude of the total deflection of point B. Assume small deformations and small rotations.
The total deflection at the mid point b is B = 1.78786mm
How to calculate total deflection ?
M(x) divided by EI (Young's Modulus x Moment of Inertia) is the double integral of the Bending Moment Equation, which can be used to calculate deflection. where E is the young's modulous and I is the moment of inertia
M(x)/E * I
Beam deflection means the state of deformation of a beam from its original shape under the work of a force or load or weight. One of the most important applications of beam deflection is to obtain equations with which we can determine the accurate values of beam deflections in many practical cases.
Thus the total deflection is 1.78786mm
To know more on deflections follow this link:
https://brainly.com/question/1581319
#SPJ4
Use Huffman code to generate codewords. Given the following Symbols and Occurrences for those symbols, what is the CodeWord for C Symbol Count A 45B 37 C 25D 19E 29 O 0O 1O 00 O 01 O 10 O 11 O 000 O None of the above
The codeword of the probability 1 in P1 is the empty string. Since 1 = 0.55 + 0.45, the codewords for 0.55 and 0.45 in P2 are 0 and 1, respectively. In P3, the codeword of 0.45 remains 1, and, since 0.55 = 0.3 + 0.25, the codeword for 0.3 is 00 and that of 0.25 is 01.
A = 000, B = 001, C = 010, D = 011, and E = 1 are the Huffman codes. If there are two symbols to be encoded in Huffman coding, the outcome will either be 01 or 10. Three symbols will result in 12 distinct encodings. a politically correct catchphrase or euphemism expression used in place of a direct or offensive remark. The diplomats engaged in a "frank and serious debate," which is euphemism for a "angry dispute," according to the official report [1880-85]. Wherever the pertinent numbers occur, entering the initial letters is the best strategy for solving. After entering them, check to see if any words come to mind. For a number of reasons, analysing letter frequency is not a particularly effective strategy for resolving these issues.
To learn more about codeword click the link below:
brainly.com/question/15734807
#SPJ4
a. as superior to using the brooklyn bridge b. as a symbol of freedom from england c. as an impressive feat of engineering d. as an example of human camaraderie
The correct response is D. as an example of human camaraderie. The sense of friendship and trust that can develop between individuals who spend a lot of time together is known as camaraderie.
A group's members who get along well and are loyal to one another are said to have camaraderie. Even if you dislike your job, you can still appreciate the friendship of your coworkers. Sports are more enjoyable and more likely to result in a victory if players get along well both on and off the field. A sense of camaraderie and friendship between two persons or a group of people is known as comradery. Though comradery is a valid alternative, camaraderie is the more common spelling. Example of a camaraderie sentence. The crew developed a strong sense of togetherness as a result of its extremely good effect. He felt a sense of unity among the group. The little groups have a sense of unity.
Learn more about camaraderie here
https://brainly.com/question/29401730
#SPJ4
In the poem "Crossing Brooklyn Ferry," how does Walt Whitman describe the ferry ride between Brooklyn and Manhattan?
A.
as superior to using the Brooklyn Bridge
B.
as a symbol of freedom from England
C.
as an impressive feat of engineering
D.
as an example of human camaraderie
The sun shining on a distribution panel has no effect on the breakers in the panel.A) True
B) False
A distribution panel's breakers are unaffected by the sun beaming on it. The assumption is incorrect.
What's an illustration of an assumption?An assumption is really something you believe to be true despite the lack of evidence. People could presume, for instance, that you are a nerd if we wear spectacles, even when it is untrue.
What would you call assumptions?Assumptions are untested beliefs that we have without even recognizing them. Our judgments, also known as inferences, are frequently founded on uncritically held presumptions. But a critical thinker is aware of these presumptions since they might occasionally be wrong or misinformed.
To know more about Assumptions visit :
https://brainly.com/question/17041979
#SPJ1
brake calipers are being discussed. technician a says the bleeder screw is located at the bottom of the cylinder bore. technician b says the fluid inlet hole is located at the top of the cylinder bore. who is correct?
Regarding the discussion about brake calipers, neither technician is correct.
A brake caliper is part of the disc brake system that performs two functions. First, it acts as a bracket for supporting the brake pads on either side of the rotor or supporting the caliper bracket itself. Second, it uses pistons to transform pressure put on the brake fluid by the master cylinder into friction on the rotor. In the design structure of brake calipers, the bleeder screw is located at the top part of the cylinder bore, whereas the fluid inlet hole is located at the center part of the cylinder bore. Thus neither technician is correct.
You can learn more about brake caliper at
https://brainly.com/question/5438877
#SPJ4
a(n) ? is a device that senses a process variable through the medium of a sensor and converts the input signal to an output signal of another form. the output of the device is a steady-state value that varies only as a predetermined function of the input (process variable). the sensor may or may not be integral with this device.
Transmitter- A device that senses a process variable using a sensor and produces an output whose steady-state value changes only in accordance with the process variable's preset function.
What is Transmitter?
A device whose steady-state value varies solely as a predetermined function and senses a process variable through the use of a sensor. a process variable that the control signal is perceived in response to. A transmitter's signal is received by an instrument, which then compares it to a predetermined value. An energy converter changes one kind of energy into another. Transducers often transform one form of energy, such mechanical or magnetic, into a measurable quantity on the other end, like an electrical signal. When it comes to process control.
To learn more about Transmitter from given link
brainly.com/question/2084370
#SPJ4