Answer:
hope it will help you out :)
Why are some waves small and some large?
(◕‿◕✿) Hey There!
Answer → The Waves Size depends on ★ wind speed ★ , ★ wind duration★ , and the ★ area over which the wind is blowing ★
✨Hope This Helps!✨
what is the kinetic energy of a 5 kg bowling ball rolling at a velocity of 10 m/s?
Answer:
K = 250 J.
Explanation:
Hello there!
In this case, by knowing that the kinetic energy is such energy associated to the movement of an object, it is possible for us to recall the formula for its calculation in terms of mass and velocity as shown below:
[tex]K=\frac{1}{2} mv^2[/tex]
Thus, given the mass and velocity, it is possible to obtain the following kinetic energy:
[tex]K=\frac{1}{2} (5kg)(10m/s)^2\\\\K=250J[/tex]
Regards!
A graph titled Average Amplitude of Waves from 2009 to 2011 with vertical axis Average Amplitude (meters) and horizontal axis Year. A line goes in straight segments from 2009 50 to 2010 175 to 2012 125.
A structural engineer is using this table to design a wall to protect a city near the ocean.
How high should the engineer build the wall?
50 meters
100 meters
150 meters
200 meters
Answer:
200
Explanation:
got it right on the test
Answer:
200
Explanation:
Drugs change the chemical processes in what organ to cause addiction?
Answer:
the brain
Explanation:
drugs mainly affect the brain to keep the addiction going
Answer:
In pituitary gland addiction causes to drugs
Mark me as brainliest
Calculate the work for the expansion of CO2 from 1.0 to 6.5 litres against pressure of 1.0 atm at constant temperature
Answer:
557.3J is the work of expansion of the CO2 gas
Explanation:
The work of expansion of a gas under constant temperature and pressure (Isobaric pressure) is:
W = P*ΔV
Where W is work
P is pressure = 1.0atm
ΔV = Final volume - Initial Volume = 6.5L - 1.0L = 5.5L
Replacing:
W = 1.0atm*5.5L
W = 5.5atmL
In Joules (1atmL = 101.325J):
5.5atmL * (101.325J / 1atmL) =
557.3J is the work of expansion of the CO2 gas
I need help on this 6th grader science plants.
Answer:
A - A fruit of vegetable will begin to grow
how could you use a thin glass tube to place the crystal at the bottom of the beaker of water
Answer:
explation
Explanation:
you put ice cold water in a glass, and in another glass put boiling water, how long would it take for the two cups of water to be roughly the
Due to the surface tension of water and the crystals ability of diffusion the crystals are placed at the bottom of the beaker of water.
What is diffusion?Diffusion is defined as the process of movement of molecules which takes place under concentration gradient. It helps in movement of substances in and out from the cell.The molecules move from lower concentration region to a higher concentration region till the concentration becomes equal.
There are 2 main types of diffusion:
1) simple diffusion-process in which substances move through a semi-permeable membrane without the aid of transport proteins.
2) facilitated diffusion- It is a passive movement of molecules across cell membrane from higher concentration region to lower concentration.
There are 2 types of facilitated diffusion one is osmosis and dialysis.
Learn more about diffusion,here:
https://brainly.com/question/14852229
#SPJ2
What is the molarity of a 100 mL solution that contains 2.00 g KCL
Answer:
The molarity will be "0.26 M".
Explanation:
The given values are:
Mass,
= 2.00 g
Volume of solution,
= 100 mL
or,
= [tex]\frac{100}{1000}[/tex]
= [tex]0.1 \ L[/tex]
Molar mass of KCl,
= 74.5 gm
Now,
Moles of KCl will be:
= [tex]\frac{Given \ mass}{Molar \ mass}[/tex]
= [tex]\frac{2}{74.5}[/tex]
= [tex]0.026[/tex]
hence,
The molarity will be:
= [tex]\frac{Moles \ of \ solute}{Volume \ of \ solution}[/tex]
On substituting the values, we get
= [tex]\frac{0.026}{0.1}[/tex]
= [tex]0.26 \ M[/tex]
A certain element has only two naturally occurring isotopes: one with 18 neutrons and the other with 20 neutrons. The element forms I- charged ions when in ionic compounds. Predict the identity of the element. What number of electrons does the charged ion have?
Answer:
[Cl-18]⁻ & [Cl-20]⁻
Explanation:
By definition isotopes are elements with the same number of protons by different number of neutrons. Elements X-18 & X-20 have 17 protons and represent Chlorine isotopes Cl-18 & Cl-20 each with 17 protons and 18 electrons to give the isotopes a -1 oxidation state. Both isotope of chlorine have 7 electron in its valence shell and 10 electrons in its core structure. Gaining 1 electron fills the valence octet and establishes a -1 oxidation state.
2.a. 3.26 g of iron powder are added to 80.0 cm3 of 0.200 mol dm-3 copper(II)
sulfate solution. The following reaction occurs: Fe (s) + CuSO4 (aq) → FeSO4 (aq)
+ Cu (s)Determine the limiting reactant showing your working. *
Your answer
Answer:
The limiting reactant is CuSO₄.
Explanation:
The reaction is:
Fe(s) + CuSO₄(aq) → FeSO₄(aq) + Cu(s) (1)
To find the limiting reactant we need to find the number of moles of the reactants.
[tex] \eta_{Fe} = \frac{m}{A_{r}} [/tex]
Where:
m: is the mass of iron = 3.26 g
[tex]A_{r}[/tex]: is the standard atomic weight of iron = 55.845 g/mol
[tex]\eta_{Fe} = \frac{3.26 g}{55.845 g/mol} = 0.058 moles [/tex]
[tex] \eta_{CuSO_{4}} = M*V [/tex]
Where:
M: is the concentration of the CuSO₄ = 0.200 mol/dm⁻³
V: is the volume of the solution = 80.0 cm³
First, we need to convert the units of the volume to dm³ knowing that 1 dm = 10 cm and 1 L= 1 dm³.
[tex] V = 80.0 cm^{3}*\frac{1 dm^{3}}{(10 cm)^{3}} = 0.080 dm^{3} [/tex]
Now, the number of CuSO₄ moles is:
[tex] \eta_{CuSO_{4}} = M*V = 0.200 mol/dm^{3}*0.080 dm^{3} = 0.016 moles [/tex]
So, to determine the limiting reactant we need to use the molar ratio from equation (1), Fe:CuSO₄ = 1:1
[tex]\eta_{Fe} = \frac{1 mol Fe}{1 mol CuSO_{4}}*0.016 moles \: CuSO_{4} = 0.016 moles[/tex]
Since we need 0.016 moles of Fe to react with 0.016 moles of CuSO₄ and initially we have 0.058 moles of Fe, then the limiting reactant is CuSO₄.
Therefore, the limiting reactant is CuSO₄.
I hope it helps you!
The limiting reactant would be CuSO4
Looking at the equation of the reaction:
Fe (s) + CuSO4 (aq) → FeSO4 (aq) + Cu (s)
The mole ratio of Fe to CuSO4 is 1:1. Thus, every 1 mole of Fe will require 1 mole of CuSO4 for reaction.
Recall that: mole = mass/molar mass
Also: mole = molarity x volume
mole of Fe = 3.26/55.8
= 0.058 moles
mole of CuSO4 = 0.200 x 80/1000
= 0.016
The mole of Fe in the reaction is more than the mole of CuSO4. Thus, CuSO4 is the limiting reactant of the reaction. Fe is in excess.
More on limiting reactants can be found here: https://brainly.com/question/14225536?referrer=searchResults
I need answers to the lab report.
Answer:
Title.
Abstract.
Introduction.
Method.
Results and analysis.
Discussion.
Conclusion.
References.
0.47 M KNO3 solution contains .757475 mol of KNO3 what is the volume
Answer:
Volume is the quantity of three-dimensional
Explanation:
3) Pick the correct definition for : A signal represented by a continuous wave *-1 analog signal-2 digitized siganal-3-encode-4-transmit-5-wave pulse.
plzzzz help brainliest and 50 points
Answer:
it is analog signal, your welcome
Analog Signal is the correct answer
Hope it helps you
Which of the following statements concerning double covalent bonds is correct?
They are found only in molecules that contain S or O.
S
They are found only in molecules that contain a coordinate covalent bond.
They occur on y between atoms containing 4 valence electrons.
They involve tie sharing of 2 electron pairs.
t
they involve tie sharing of 2 electrons pairs.
what is the similar of snow and sleet pls help me
Answer:
Explanation: Snow forms in clouds at temperatures below freezing. As snow falls through the atmosphere, the air remains at least 32° F or colder. ... It then re-enters another pocket of cold air before reaching the surface. The snowflake refreezes and becomes an ice pellet we call sleet.
put some ice in a clean glass. examine it every 3 minutes for half oan hour . DIscribe what happens to the ice
Answer:
the ice starts melting and turns into water
The isotopes K-37 and K-42 have the same...
1) number of neutrons
2) number of protons
3) mass number for their atoms
Answer:
WHEA O IN AN EREM STATO. PETUA TOT low 6 EN 6ACY STATE ... Determine both the total number of protons and the total number of neutrons in an atom of the naturally occurring carbon isotope with the largest mass number.
Explanation:
ok
La clorurarea catalitică a toluenului, se obţine un amestec format din 2-clorotoluen, 4-clorotoluen şi benzennereacționat în raport molar de 3 : 2 : 1. Calculaţi cantitatea de 2-clorotoluen, exprimată în moli, care se obținedin 110,4 g de toluen, în în prezența catalizatorului FeCl3.
Answer:
i dont lnow you heat alcohol over an open flame
Balance the following chemical equation by providing the correct coefficients:
[ ]HBr + [ ]Ba(OH)2 -> [ ]BaBr2 + [ ]H20
Answer:
2HBr + Ba(OH)2 → BaBr2 + 2H2O
Explanation:
Hydrogen Bromide + Barium Hydroxide = Barium Bromide + Water
The balanced chemical equation with the correct coefficients is 2HBr + Ba(OH)₂ → BaBr₂ + 2H₂O.
First balancing the barium (Ba) atoms first. There is one barium atom on the left side and one on the right side, so no coefficients are needed for barium.
HBr + Ba(OH)₂ → BaBr₂ + H₂O
There is one hydrogen atom on the left side and two hydrogen atoms on the right side. To balance the hydrogen, place a coefficient of 2 in front of HBr:
2HBr + Ba(OH)₂ → BaBr₂ + H₂O
There are two bromine atoms on the left side and two bromine atoms on the right side, so they are already balanced.
2HBr + Ba(OH)₂ → BaBr₂ + H₂O
There is one barium atom on the left side and one barium atom on the right side, so they are already balanced.
Balance the oxygen (O) atoms. There are two oxygen atoms on the left side and only one on the right side. To balance the oxygen, place a coefficient of 2 in front of H₂O.
2HBr + Ba(OH)₂ → BaBr₂ + 2H₂O
To learn more about the coefficients, follow the link:
https://brainly.com/question/23702958
#SPJ6
How many atoms does methane=CH4?
Answer:
It has 1 carbon atom and 4 hydrogen atoms
Explanation:
hope this helps :)
In a chemical reaction, the mass of the reactants is 13.3 grams. Which of the
following could represent the mass of the products?
Answer:
26.6
Explanation:
Determine the oxidation number of the element "X" in H2XO4.
Which event is an example of condensation?
"Fog forms in a valley", a physical process called condensation occurs when a gas or vapour transforms into a liquid state.
Which of the following example of condensation?On a chilly soda can, water gathers. As the air cools around the container, water vapor in the atmosphere reaches its dew point and condenses into liquid droplets. Condensation is the conversion of water vapor into liquid. On the outside of a chilly glass or container, water vapor condenses and turns into liquid water (sweat).
What three condensation reactions are examples?Aldol condensation, Knoevenagel condensation, Claisen condensation, and Dieckman condensation (intramolecular Claisen condensation) are a few examples of common condensations that produce alcohols as a by-product.
To know more about Condensation visit:-
https://brainly.com/question/1447093
#SPJ1
Where did water become gas?
F
E
Temperature (°C)
В
Time (minutes)
O A-B
OB-C
OE-F
OD-E
A gas has the volume of 45mL at 25 C is heated to 50 C. What is the new volume of the gas? P1V1 = P2V2 V1/T1 = V2/T2 PV = nRT V1/T1 x V2/T2
Answer:
Option b (V1/T1 = V2/T2) is the right alternative or the new volume will be "0.048 L".
Explanation:
The given values are:
Temperature,
T₁ = 25°C
or,
= 298.15 K
T₂ = 50°C
or,
= 323.15 K
Volume,
V₁ = 45 mL
or,
= 0.045 L
V₂ = ?
As we know,
⇒ [tex]\frac{V_1}{T_1} =\frac{V_2}{T_2}[/tex]
Or,
⇒ [tex]V_2=\frac{V_1\times T_2}{T_1}[/tex]
On substituting the values, we get
⇒ [tex]=\frac{0.045\times 323.15}{298.15}[/tex]
⇒ [tex]=\frac{14.541}{298.15}[/tex]
⇒ [tex]=0.048 \ L[/tex]
Which reaction type is really part of another type of reaction but treated separately? Explain
Answer:
Oxidation - reduction reaction which is called redox reaction.
Explanation:
The type of reaction that is a part of another type but treated separately is called Oxidation - reduction reaction.
Thus is because they usually involve 2 separate half reactions which are oxidation reactions that involve loss of electrons and then reduction equations which involve gain of electrons.
They are treated separately for example when sodium reacts with chlorine to form sodium chloride.
2Na + Cl2 = 2NaCl
Now, sodium undergoes oxidation by loosing elctrons and it's half reaction is;
2Na → 2Na^(+) + 2e^(-)
Meanwhile chlorine undergoes reduction by gaining electrons and its half reaction is;
Cl2 + 2e^(-) → 2Cl^(-)
PLEASE HELP ASAP! AND PLEASE DO NOT GIVE ME ANY VIRUSES!
Carbon dioxide and oxygen are linked together in the carbon and oxygen cycle. There are two cellular processes involved in this cycle. What are they called, and what does each process make?
Mark two answers below.
Carbon dioxide is generated by cellular respiration and released into the atmosphere.
Cellular respiration makes oxygen that plants and animals can release into the atmosphere.
Carbon dioxide is a product of photosynthesis that plants release into the atmosphere.
Photosynthesis makes oxygen that plants can release into the atmosphere.
Answer:
The first one and the last one.
Explanation:
Carbon dioxide is generated by cellular respiration and released into the atmosphere.
Photosynthesis makes oxygen that plants can release into the atmosphere.
When two solutions are combined, what evidence would show a chemical
reaction has occurred? *
temperature remains constant
a precipitate forms
volume increases
Define a transverse wave
please help me ;-; I need help grades are in tomorrow
Explanation:
Sorry i cant see the mass number of Lithium.
And fyi if the N in question refers to Neutron number, the answer is as i stated.
But, if the N refers to Nucleon number the answer is proton number + mass number