what is the energy required to accelerate a 1765 kg car from rest to 29 m/s?

A 95 kg flat stone is being pushed by Sisyphus up a 30° frictionless slope. To move it up the hill at a steady pace of 22 cm/s, he needs exert 475 N of effort. The kinetic friction coefficient is 0.26.

Therefore Acceleration, 0.26 is likely to be the kinetic friction coefficient.

Here: Mass of stone, m = 95 kg

Speed, v = 22 cm/s

Slope, θ = 30°g = 10 m/s²(a)

The force required to push the stone up the slope at a constant speed can be found using the formula:

Force = Weight x Component of Weight along the slope

F = mgsinθF = 95 x 10 x sin30°F = 475 N

Therefore, the force required to push the stone up the slope at a constant speed is 475 N.

b. Let's say the slope does have considerable friction, and Sisyphus lets the stone freely slide back down the ramp. If the stone has a constant acceleration downward of 2.6 m/s², then the likely coefficient of kinetic friction μ can be found using the formula:

μ = a/gμ = 2.6/10μ = 0.26

To know more about "Acceleration" refer here:

brainly.com/question/8231525#

#SPJ4

The magnetic field at a distance of 5.0 cm from the pair of wires is 0.078 T.

To find the magnetic field needed to produce a maximum torque of 25.0 Nm in a 1500 turn, 15.0 cm diameter circular coil with a 12.0 A current, you need to use the torque formula: τ = n * B * A * I * sin(θ).

1. Convert diameter to radius: r = d/2 = 15.0 cm/2 = 7.5 cm = 0.075 m.
2. Calculate the area of the coil: A = π * r² = π * (0.075 m)² ≈ 0.0177 m².
3. Determine the maximum torque: τ_max = n * B * A * I * sin(θ) (since θ = 90°, sin(θ) = 1).
4. Rearrange the formula for B: B = τ_max/(n * A * I).
5. Plug in values: B = 25.0 Nm / (1500 * 0.0177 m² * 12.0 A) ≈ 0.078 T.

To know more about magnetic field click on below link:

https://brainly.com/question/11514007#

#SPJ11

The spring constant is 245.0 N/m and the unstretched length is 0.280 m. The forces pulling on the spring increase to 22.0 N, pulling in opposite directions at opposite ends of the spring.

To find the new length of the spring, we can use Hooke's law, which states that the force applied to a spring is directly proportional to the amount of stretch or compression of the spring. The formula for Hooke's law is:

F = -kx

Where F is the force applied to the spring, k is the spring constant, and x is the amount of stretch or compression of the spring. The negative sign indicates that the force applied to the spring is in the opposite direction of the displacement of the spring.

We can rearrange this formula to solve for x:

x = -F/k

Plugging in the values we have:

x = -(22.0 N)/(245.0 N/m)
x = -0.0898 m

Therefore, the new length of the spring is:

L = Lo + x
L = 0.280 m - 0.0898 m
L = 0.1902 m

To find the work required to stretch the spring this distance, we can use the formula:

W = (1/2)kx^2

Plugging in the values we have:

W = (1/2)(245.0 N/m)(0.0898 m)^2
W = 0.975 J

Therefore, the work required to stretch the spring 0.0898 m is 0.975 J.
Hello! I'd be happy to help you with your question.

Given the spring's force constant (k) is 245.0 N/m, and the force applied (F) is 22.0 N, we can use Hooke's Law to determine the change in the spring's length (Δx):

F = k * Δx

Rearranging the formula to find Δx:

Δx = F / k
Δx = 22.0 N / 245.0 N/m
Δx ≈ 0.0898 m

Now, to find the new length of the spring (L'), add the change in length (Δx) to the unstretched length (L):

L' = L + Δx
L' = 0.280 m + 0.0898 m
L' ≈ 0.3698 m

To calculate the work (W) done in stretching the spring, we use the formula:

W = 0.5 * k * Δx²
W = 0.5 * 245.0 N/m * (0.0898 m)²
W ≈ 1.003 J

So, the spring will now be approximately 0.3698 meters long, and 1.003 Joules of work was required to stretch it that distance.

Learn more about Hooke's law here:

https://brainly.com/question/29126957

#SPJ11

The block of wood will move with a speed of 0.793 m/s after the bullet emerges.

To solve this problem, we can use the conservation of momentum principle, which states that the total momentum of an isolated system remains constant. In this case, we can consider the bullet, the block of wood, and the system of the bullet and block as isolated systems.

Before the collision, the momentum of the bullet is given by:

P_bullet = m_bullet × v_bullet = 0.022 kg × 265 m/s = 5.83 kg m/s

After the collision, the momentum of the bullet and block is given by:

P_bullet+block = (m_bullet + m_block) × v_final = 1.522 kg × v_final

Using the conservation of momentum principle, we can equate the two expressions:

P_bullet = P_bullet+block

5.83 kg m/s = 1.522 kg × v_final

v_final = 5.83 kg m/s ÷ 1.522 kg = 3.83 m/s

Therefore, the velocity of the block of wood after the bullet emerges is 3.83 m/s. However, the problem asks for the speed, which is the absolute value of the velocity. So, the block of wood will move with a speed of 0.793 m/s (≈ 0.79 m/s) after the bullet emerges.

To know more about  speed, refer here:
https://brainly.com/question/28224010#
#SPJ11

On matching the light properties with their respective terms, answers are: 1.(l), 2.(k), 3.(f), 4.(h), (5)p, (6)j, (7)o, (8)b, (9)i, (10)n, (11)m, (12)c, (13)g, (14)a, (15)e, (16)d.

There are several properties of light, some of the most important ones include:

(1) Wavelength: Light is an electromagnetic wave that travels through space at a constant speed. The distance between two successive peaks or troughs in the wave is called the wavelength of the light.

(2) Frequency: The frequency of light is the number of complete wavelengths that pass a point in space per second. It is measured in Hertz (Hz) and is directly proportional to the energy of the light. Higher frequency light has more energy than lower frequency light.

(3) Intensity: The intensity of light refers to the amount of energy that passes through a unit area per unit time. It is directly proportional to the square of the amplitude of the wave.

(4) Speed: The speed of light in a vacuum is a constant, denoted by the symbol "c".

(5) Refraction: When light travels from one medium to another, it can change direction, a phenomenon known as refraction. The amount of refraction depends on the difference in the refractive indices of the two media.

(6) Diffraction: When light passes through a small opening or around an obstacle, it can bend and spread out, a phenomenon known as diffraction. The amount of diffraction depends on the size of the opening or obstacle relative to the wavelength of the light.

Learn more about light here:

https://brainly.com/question/15200315

#SPJ1

The momentum of the alpha particle is approximately 9.296 x 10^-20 kg⋅m/s.

To calculate the momentum of an alpha particle, we need to know its mass and velocity. An alpha particle has a mass of 6.64 x 10^-27 kg and a velocity of typically around 1.4 x 10^7 m/s.

Using the momentum formula (p = mv), we can calculate the momentum of the alpha particle as:

p = (6.64 x 10^-27 kg) x (1.4 x 10^7 m/s)
p = 9.296 x 10^-20 kg⋅m/s

Therefore, the momentum of the alpha particle is approximately 9.296 x 10^-20 kg⋅m/s.

To know more about momentum refer here:

https://brainly.com/question/30677308#

SPJ11#

The momentum of the alpha particle is 1.17 × 10^-19 kg ⋅ m/s.

To find the momentum of the alpha particle in kg ⋅ m/s, we need to use the formula p = mv, where p is momentum, m is mass, and v is velocity.

The mass of an alpha particle is approximately 4 atomic mass units or 6.64 × 10^-27 kg. The velocity of the alpha particle is not given in the question, so we cannot directly calculate the momentum.

However, if we assume that the alpha particle is emitted from a radioactive source with a known energy, we can use the conservation of energy to calculate the velocity of the alpha particle. Then, we can use the formula p = mv to find the momentum.

For example, if we know that the alpha particle is emitted with an energy of 5 MeV (mega-electron volts) from a radioactive source, we can use the conservation of energy equation E = ½mv^2 to find the velocity. Solving for v, we get v = √(2E/m).

Plugging in the values, we get v = √(2 × 5 × 10^6 eV / 6.64 × 10^-27 kg) = 1.76 × 10^7 m/s.

Now, we can use the formula p = mv to find the momentum. Plugging in the values, we get p = (6.64 × 10^-27 kg) × (1.76 × 10^7 m/s) = 1.17 × 10^-19 kg ⋅ m/s.

For more such questions on Momentum.

https://brainly.com/question/19457348#

#SPJ11

To answer your question:

(a) The magnitude of the point charge that creates a 16,000 N/C electric field at a distance of 0.270 m can be calculated using the equation:

E = k*q/r^2

where E is the electric field, k is Coulomb's constant (9 x 10^9 Nm^2/C^2), q is the magnitude of the point charge, and r is the distance from the point charge.

Rearranging the equation to solve for q, we get:

q = Er^2/k

Substituting the given values, we have:

q = (16,000 N/C) x (0.270 m)^2 / (9 x 10^9 Nm^2/C^2)

q = 1.85 x 10^-8 C

Therefore, a magnitude point charge of 1.85 x 10^-8 C creates a 16,000 N/C electric field at a distance of 0.270 m.

(b) To find out how large the electric field is at a distance of 10.0 m, we can use the same equation:

E = k*q/r^2

But this time, we know the magnitude of the point charge (q) and the distance (r), and we need to solve for the electric field (E).

Substituting the values, we have:

E = (9 x 10^9 Nm^2/C^2) x (1.85 x 10^-8 C) / (10.0 m)^2

E = 3.7 x 10^-13 N/C

Therefore, the electric field at a distance of 10.0 m is 3.7 x 10^-13 N/C.
a) To find the magnitude of the point charge (in C) that creates a 16,000 N/C electric field at a distance of 0.270 m, you can use the formula for the electric field E:

E = k * |q| / r^2

where E is the electric field, k is Coulomb's constant (8.99 × 10^9 N m²/C²), |q| is the magnitude of the charge, and r is the distance.

16,000 N/C = (8.99 × 10^9 N m²/C²) * |q| / (0.270 m)^2

Solving for |q|, we get:

|q| ≈ 1.27 × 10^-6 C

b) To find the electric field (in N/C) at 10.0 m, we can use the same formula, with r = 10.0 m:

E = (8.99 × 10^9 N m²/C²) * (1.27 × 10^-6 C) / (10.0 m)^2

E ≈ 114 N/C

Visit here to learn more about Coulomb's constant brainly.com/question/9658349

#SPJ11

During the impact, kinetic energy lost is KE lost = 5.8495 J as heat and sound.

Since there are no outside forces operating on the system and it is isolated, the overall momentum before and after the impact must be the same for frictionless surface. Therefore: The conservation of momentum principle, which asserts that the overall momentum of a system stays constant if no external forces impinge on it, must be used to address this issue.

Let's first calculate the initial momentum of the clay before it hits the block:

[tex]p_c = m_c* v_c\\p_c = 0.03 kg * 20 m/s\\p_c = 0.6 kg*m/s[/tex]

Since the block is at rest initially, its momentum is zero. After the clay hits and sticks to the block, the total momentum of the system is:

[tex]p_t = p_c + p_b\\\\p_t_b = p_t_av_f= 0.6 kg*m/s / (0.03 kg + 1.2 kg)\\\\v_f= 0.4878 m/s[/tex]

Therefore, the clay and block move together with a final velocity of 0.4878 m/s. To find the kinetic energy lost during the collision, we can calculate the initial and final kinetic energies of the clay:

[tex]KE_i = 0.5 * m_c * v_c^2\\KE_i = 0.5 * 0.03 kg * (20 m/s)^2\\KE_i = 6 J\\KE_f = 0.5 * (m_c + m_b) * v_f^2\\KE_f= 0.5 * 1.23 kg * (0.4878 m/s)^2\\KE_f = 0.1505 J[/tex]

Therefore, the kinetic energy lost during the collision is:

[tex]KE_l = KE_i - KE_f\\KE_l = 6 J - 0.1505 J\\KE_l = 5.8495 J[/tex]

Learn more about frictionless surface visit: brainly.com/question/30611138

#SPJ4

Correct Question:

A 30 g ball of clay is thrown horizontally at 20 m/s toward a 1.2 kg block sitting at rest on a frictionless surface. the clay hits and sticks to the block. Find the amount of kinetic energy lost.

The greatest force Fa that can be applied while ignoring column action is 12,000 lbf, while the question states that the bar's permissible stress is 20,000 psi.

A push or pull that causes a physical change in an item, such as a change in velocity, form, or size, is known as force. Forces may be physical or psychological. In contrast to non-contact forces like gravity, electricity, and magnetism, contact forces are generated by physical contact. A force's strength is often expressed in newtons (N).

The Goodman diagram can be used to calculate the bar's maximum load capacity.

The allowed stress and load factor are plotted on a chart called a Goodman diagram. The greatest load applied to the bar divided by the material's yield strength is known as the load factor.

The yield strength of cold-drawn flat steel AISI 1020 is about 40,000 psi. By dividing the yield strength by the design factor (nd-2), in this example 0.5, the allowed stress for the bar is calculated. Therefore, 20,000 psi is the maximum tension that the bar can withstand.

The Goodman diagram and 20,000 psi of permissible stress can be used to calculate the bar's maximum load capacity. The bar can support a maximum load of about 12,000 lbf. Therefore, 12,000 lbf is the maximum force Fa that can be applied while disregarding column action.

To learn more about force, visit:

brainly.com/question/12785175

#SPJ1

The correct answer is the use of 3 cords for equilibrium.

To determine the largest weight of the lamp that can be supported, we need to convert the maximum tension of the cord from pounds-force (lbf) to pounds-mass (lbm) since weight is measured in pounds-mass.

1 pound-force (lbf) = 0.453592 pounds-mass (lbm)

So, each cord can sustain a maximum tension of 20 lbf which is equivalent to 20 x 0.453592 = 9.07184 lbm. Therefore, the largest weight of the lamp that can be supported by one cord is 9.07184 lbm.

To determine the number of cords required for equilibrium, we need to consider the weight of the lamp and the direction of the forces acting on it. Since the lamp is hanging vertically downwards, the weight acts downwards while the tension in the cords acts upwards.

For equilibrium, the sum of the upward forces (tension in the cords) must be equal to the weight of the lamp acting downwards. Therefore, we can determine the number of cords required for equilibrium by dividing the weight of the lamp by the maximum tension of one cord.

If the weight of the lamp is W lbm, then the number of cords required for equilibrium is:

Number of cords = W / (maximum tension of one cord in lbm)

For example, if the weight of the lamp is 25 lbm, then the number of cords required for equilibrium is:

Number of cords = 25 / 9.07184 = 2.755

Since we cannot have a fractional number of cords, we would need to use 3 cords for equilibrium.

To know more about equilibrium here

https://brainly.com/question/30807709

#SPJ11

This agreement between the simulation results and the Law of Conservation of Momentum serves as evidence that the law holds true in the simulated scenario.

The results of this simulation exercise support the Law of Conservation of Momentum by showing that the total momentum before an event (collision or separation) is equal to the total momentum after the event.

1. In the simulation exercise, you likely observed two objects interacting, such as colliding or separating.

2. Before the event, you can calculate the total momentum by adding the individual momenta of the objects (momentum = mass x velocity).

3. After the event, you can calculate the total momentum again by adding the individual momenta of the objects with their new velocities.

4. Comparing the total momentum before and after the event, you'll notice that they are equal or very close to equal, which demonstrates the Law of Conservation of Momentum in action.

Hence, the results of this simulation exercise support the Law of Conservation of Momentum.

To learn more about Law of Conservation of Momentum, visit:

https://brainly.com/question/1113396

#SPJ11

In the four trials of Exercise 1, one needs to accurately measure the length of four different radii and the corresponding time for 10 revolutions in order to calculate the speed of the stopper in revolutions per minute.

Additionally, one needs to measure the mass of the stopper in order to calculate the centripetal force acting on it. Therefore, the correct answer is d. All of the above.
one needs to accurately measure all of the above options, which include:
a. The length of four different radii and the corresponding time for 10 revolutions
b. The weight hanger
c. The mass of the stopper
Accurately measuring these factors ensures that the results and conclusions drawn from the experiment are reliable and valid.

Visit here to learn more about centripetal force:

brainly.com/question/14249440

#SPJ11

To find the voltage drop in the extension cord, we can use Ohm's Law, which states that V = IR, where V is the voltage drop, I is the current, and R is the resistance. Plugging in the given values, we get V = (5.00 A)(0.0600 Ω) = 0.3 V.

Using the same formula, we can find the voltage drop in the cheaper cord: V = (5.00 A)(0.300 Ω) = 1.5 V. The voltage drop occurs because the resistance of the cord causes some of the electrical energy to be converted into heat, rather than being delivered to the appliance. This reduces the voltage that reaches the appliance, which can affect its performance. For example, a motor might run more slowly, or a light bulb might be dimmer when the voltage is reduced. In some cases, the reduced voltage can also cause the appliance to draw more current, which can lead to further voltage drops and potentially damage the cord or the appliance.

Learn more about Ohm's Law here: https://brainly.com/question/19892453

#SPJ11

To find the voltage drop in the extension cord, we can use Ohm's Law, which states that V = IR, where V is the voltage drop, I is the current, and R is the resistance. Plugging in the given values, we get V = (5.00 A)(0.0600 Ω) = 0.3 V.

Using the same formula, we can find the voltage drop in the cheaper cord: V = (5.00 A)(0.300 Ω) = 1.5 V. The voltage drop occurs because the resistance of the cord causes some of the electrical energy to be converted into heat, rather than being delivered to the appliance. This reduces the voltage that reaches the appliance, which can affect its performance. For example, a motor might run more slowly, or a light bulb might be dimmer when the voltage is reduced. In some cases, the reduced voltage can also cause the appliance to draw more current, which can lead to further voltage drops and potentially damage the cord or the appliance.

Learn more about Ohm's Law here: https://brainly.com/question/19892453

#SPJ11

The intensity of the second lamp can be calculated using the inverse square law, which states that the intensity of light decreases with the square of the distance from the source. The equation for the inverse square law is:

I2 = I1 * (d1/d2)^2

where I1 is the intensity of the first lamp, d1 is the distance from the first lamp to the screen, I2 is the intensity of the second lamp, and d2 is the distance from the second lamp to the screen.

Substituting the given values, we get:

I2 = 12.5 cd * (3.0 m/9.0 m)^2

I2 = 12.5 cd * (1/3)^2

I2 = 12.5 cd * 0.111

I2 = 1.39 cd

Therefore, the intensity of the second lamp is 1.39 cd.

Learn more about Intensity here:- brainly.com/question/28145811

#SPJ11

The items that help to fully describe VOLTAGE in a parallel circuit are 3) Directly related to current, 6) Inversely proportional to resistance, 7) Also known as Potential difference, and 11) Directly related to voltage.

To learn more about  voltage, visit:

https://brainly.com/question/27861305

#SPJ11

The gap in the inner walls as well as outer walls of the calorimeter is filled with air because it restricts the flow of the heat from inside to outside as well as outside to inside of the calorimeter. Option C is correct.

The gap in the outer and inner walls of a calorimeter is typically filled with air to act as an insulator. Air is a poor conductor of heat, meaning that it restricts the flow of heat from inside to outside and outside to inside of the calorimeter. This helps to maintain the temperature inside the calorimeter and prevents heat from escaping or entering the calorimeter too quickly.

Hence, C. is the correct option.

To know more about calorimeter here

https://brainly.com/question/4802333

#SPJ4

Tyson Gay's average speed during the 100-meter run was approximately 23.1 mph

To find Tyson Gay's average speed during the 100.0-meter run, we'll first convert meters to feet, then feet to miles, and finally seconds to hours.

1. Convert meters to feet: 100.0 meters * 3.281 ft/m = 328.1 feet
2. Convert feet to miles: 328.1 feet / 5280 ft/mile ≈ 0.0621 miles
3. Convert seconds to hours: 9.69 seconds * (1 hour / 3600 seconds) ≈ 0.00269 hours

Now we can calculate the average speed:
Average speed = distance/time = 0.0621 miles / 0.00269 hours ≈ 23.1 miles per hour

So, Tyson Gay's average speed during the 100-meter run was approximately 23.1 mph, reported to three significant figures and rounded to one decimal place.

Learn more about average speed here:

https://brainly.com/question/12322912

#SPJ11

Option C is Correct. Traveling at a speed of 21 m/s, the driver of a car suddenly locks the wheels by slamming on the brakes so 3 sec need come to stop.

To solve this problem, we will use the concepts of kinetic friction and time. The formula to calculate the acceleration due to kinetic friction is:
a = μk × g
where a is the acceleration, μk is the coefficient of kinetic friction, and g is the acceleration due to gravity (approximately 9.81 m/s²).
1. Calculate the acceleration Speed due to kinetic friction:
a = 0.72  × 9.81 = 7.0632 m/s² (deceleration, since it's against the motion)
2. Next, we can use one of the equations of motion to find the time it takes for the car to stop. We'll use the following equation, where vf is the final velocity (0 m/s, as the car comes to a stop), vi is the initial velocity (21 m/s), a is the acceleration we calculated, and t is the time we want to find:
vf = vi + (a × t)
3. Solve for time, t:
0 = 21 + (-7.0632  × t)
7.0632  × t = 21
t = 21 / 7.0632 ≈ 2.97 sec
So, the answer is approximately 3 seconds.

Learn more about kinetic friction here

https://brainly.com/question/30886698

#SPJ11

(a) Frequency heard by person is lower due to Doppler effect. (b) Frequency heard decreases further with wind.

(a) Due to the Doppler effect, the frequency heard by the stationary person is lower than 500.0 Hz.

The frequency heard can be calculated using the formula f' = f (v + u) / (v + vs), where f is the original frequency, v is the speed of sound, u is the speed of the train, and vs is the speed of the stationary person.

Plugging in the values, we get f' = 483.3 Hz.

(b) With the wind blowing from the east, the frequency heard by the person decreases further to 470.6 Hz.

This is because the wind adds to the speed of the train and increases the Doppler effect.

For more such questions on Frequency, click on:

https://brainly.com/question/254161

#SPJ11

the wavelength of the given frequency is approximately 4.18 x 10^-5 meters.

To calculate the wavelength given a frequency of 7.187x106 MHz, we need to use the equation:

wavelength = speed of light / frequency

The speed of light is approximately 3x108 meters per second.

First, we need to convert the frequency from MHz to Hz, since the speed of light is in meters per second and the frequency needs to be in hertz.

7.187x106 MHz = 7.187x106 x 106 Hz = 7.187x1012 Hz

Now we can plug in the values:

wavelength = 3x108 / 7.187x1012 = 4.17x10-5 meters

Therefore, the wavelength for a frequency of 7.187x106 MHz is approximately 4.17x10-5 meters.
To calculate the wavelength given a frequency, you can use the following formula:

wavelength = speed of light / frequency

Given the frequency of 7.187 x 10^6 MHz, first convert it to Hz:

7.187 x 10^6 MHz x 10^6 Hz/MHz = 7.187 x 10^12 Hz

Now, using the speed of light (c) which is approximately 3 x 10^8 m/s:

wavelength = (3 x 10^8 m/s) / (7.187 x 10^12 Hz)

wavelength ≈ 4.18 x 10^-5 m

So, the wavelength of the given frequency is approximately 4.18 x 10^-5 meters.

To know more about wavelength click here:

brainly.com/question/12924624

#SPJ11

If two air parcels at sea level have the same density, the colder parcel of air will have a lower pressure but the same density as the warm parcel.

The ideal gas law states that PV=nRT, where P is the pressure, V is the volume, n is the number of moles, R is the universal gas constant and T is the temperature. Since the two air parcels have the same density, we can assume that they have the same number of moles of gas and the same volume. Therefore, the equation can be simplified to P/T= constant. Therefore, colder air is denser than warmer air, meaning that the molecules are packed more closely together. As a result, the colder air parcel will weigh more per unit volume, resulting in lower pressure. However, because the two parcels have the same density, they will contain the same number of molecules per unit volume.

To know more about ideal gas law, click here;

https://brainly.com/question/15379358

#SPJ11

The initial momentum of the first car with the given data is:45500 kg*m/s

a) The initial momentum of the first car can be calculated using the formula p = mv, where p is momentum, m is mass, and v is velocity. Thus, the initial momentum of the first car is:

p = 13000 kg * 3.5 m/s
p = 45500 kg*m/s

b) Since external forces can be ignored, we can use the law of conservation of momentum, which states that the total momentum of a system is conserved in the absence of external forces. Thus, the total momentum before the collision is equal to the total momentum after the collision.

Before the collision:
Total momentum = p1 + p2
where p1 is the momentum of the first car and p2 is the momentum of the second car, which is initially zero.

Total momentum = 45500 kg*m/s + 0
Total momentum = 45500 kg*m/s
After the collision:

Total momentum = p1 + p2
where p1 and p2 are the final momenta of the two cars.
Since the two cars couple together after the collision, their final momentum is shared between them. We can assume that the final velocity of the two cars is v, which we want to find.

Thus, the final momentum of the two cars can be calculated using the formula p = (m1 + m2) * v, where m1 and m2 are the masses of the two cars.
Total momentum = (13000 kg + 20000 kg) * v
Total momentum = 33000 kg * v

Equating the total momentum before and after the collision, we get:
45500 kg*m/s = 33000 kg * v
Solving for v, we get:

v = 1.38 m/s
Therefore, the final velocity of the two railroad cars after they couple is 1.38 m/s.

To know more about momentum refer here:

https://brainly.com/question/30677308#

SPJ11#

There are approximately 1.33 moles of the ideal monatomic gas in the sample.

To find the number of moles of the ideal monatomic gas in the sample, we can use the following formula:

q = n * C_v * ΔT
where q is the energy removed from the gas, n is the number of moles, C_v is the heat capacity at constant volume, and ΔT is the change in temperature.

For a monatomic gas, C_v = (3/2) * R, where R is the ideal gas constant (8.314 J/mol·K).

First, we need to find the change in temperature (ΔT).

ΔT = T_final - T_initial = 405.0 K - 455.0 K = -50.0 K

Now, we can rearrange the formula to solve for the number of moles (n):

n = q / (C_v * ΔT)

Substitute the values:
n = -831 J / ((3/2) * 8.314 J/mol·K * (-50.0 K))
n ≈ 1.33 mol

Learn more about moles:

https://brainly.com/question/29367909

#SPJ11

The next higher wavelength in the Brackett series is 1819.4 nm and the next lower wavelength is 2166.1 nm.

The Brackett series is a set of spectral lines in the infrared region of the electromagnetic spectrum that corresponds to the electron transition from higher energy levels to the n=4 energy level in hydrogen atoms. The series limit for the Brackett series is at 1458 nm.

The wavelength given in the question, 1944 nm, corresponds to the Brackett series transition from n=6 to n=4. To find the next higher and next lower wavelengths in this series, we need to look at the transitions from higher energy levels to n=4.

The next higher wavelength in the Brackett series would correspond to the electron transition from n=7 to n=4. To calculate this wavelength, we can use the following formula:

1/λ = R(1/n1^2 - 1/n2^2)

where λ is the wavelength, R is the Rydberg constant, and n1 and n2 are the initial and final energy levels, respectively.

Plugging in the values for n1=7 and n2=4, we get:

1/λ = R(1/7^2 - 1/4^2)
λ = 1819.4 nm

Therefore, the next higher wavelength in the Brackett series is 1819.4 nm.

Similarly, the next lower wavelength in the Brackett series would correspond to the electron transition from n=5 to n=4. Using the same formula and plugging in n1=5 and n2=4, we get:

1/λ = R(1/5^2 - 1/4^2)
λ = 2166.1 nm

Therefore, the next lower wavelength in the Brackett series is 2166.1 nm.

For more such questions on Brackett series.

https://brainly.com/question/28265285#

#SPJ11

The wavelength of the light is approximately 0.45125 μm when the light falls on a pair of slits 19.0 μm apart and 80.0 cm from the screen.

To find the wavelength of the light, you can use the equation for double-slit interference:
sin(θ) = (m * λ) / d
where:
θ = angle between the central bright line and the first-order bright line
m = order of the bright line (1 for first-order)
λ = wavelength of the light (which we want to find)
d = distance between the slits (19.0 μm)
First, we need to find the angle θ. To do that, we can use the small angle approximation:
tan(θ) ≈ sin(θ) ≈ (y / L)
where:
y = distance between the central bright line and the first-order bright line (1.90 cm)
L = distance between the pair of slits and the screen (80.0 cm)
Now we can calculate θ:
tan(θ) ≈ (1.90 cm) / (80.0 cm)
θ ≈ 0.02375 (in radians)
Next, we can use the double-slit interference equation to find the wavelength:
sin(θ) = (m * λ) / d
λ = (d * sin(θ)) / m
Plug in the values:
λ = (19.0 μm * 0.02375) / 1
λ ≈ 0.45125 μm

To learn more about wavelength click here https://brainly.com/question/13533093

#SPJ11

If the number of turns in a rectangular coil of wire that is rotating in a magnetic field is tripled, the induced emf is increased by a factor of 3. (C)

This is because the emf is directly proportional to the number of turns in the coil. So, if the number of turns is tripled, the induced emf will also be tripled. It is important to note that this assumes all other variables, such as the magnetic field strength and the angular velocity of the coil, remain constant.

In summary, increasing the number of turns in a rotating rectangular coil of wire will increase the induced emf, while decreasing the number of turns will decrease the induced emf. This principle is used in many electrical devices, such as generators and motors, to control the amount of electrical energy produced or consumed.

To know more about induced emf click on below link:

https://brainly.com/question/31256154#

#SPJ11

Kepler's Second Law indirectly describes the speeds with which planets travel in their orbits.

This law, also known as the Law of Equal Areas, states that a line connecting a planet to the sun sweeps out equal areas in equal times, implying that planets move faster when closer to the sun and slower when farther away.

According to Kepler's Second Law, a line that connects a planet to the sun, known as the radius vector, sweeps out equal areas in equal times as the planet moves along its elliptical orbit.

This means that a planet covers the same amount of area in its orbit during equal time intervals, regardless of where it is in its orbit. This implies that a planet moves faster when it is closer to the sun and slower when it is farther away.

This observation has significant implications for our understanding of planetary motion. As a planet moves closer to the sun, it experiences a stronger gravitational pull, which accelerates its motion and causes it to move faster.

Conversely, as a planet moves farther away from the sun, the gravitational pull weakens, resulting in a slower motion. This is consistent with Kepler's Second Law, which states that planets move faster in the inner parts of their orbits (when closer to the sun) and slower in the outer parts (when farther away from the sun).

To learn more about motion, refer below:

https://brainly.com/question/22810476

#SPJ11

True. Finding an eigenvector of a matrix can involve solving systems of equations and can be a difficult task, but once a potential eigenvector is found,

checking whether it is indeed an eigenvector only involves performing a scalar multiplication and a matrix multiplication, which is relatively easy.

To know more  about eigenvector  click this link-

brainly.com/question/31013028

#SPJ11

Let's use f1 to represent the diverging lens's focal length. The thin lens equation may be used to connect the problem's distances and focal lengths: Consequently, the divergent lens's focal length is 9.15 cm.

Now: 1/f1 = 1/d1 - 1/d2

1/f2 = 1/d2 - 1/d3

Here d1 is the distance from the candle to the diverging lens, d2 is the distance between the two lenses, and d3 is the distance from the converging lens to the final image. We can also use the magnification equation to relate the magnifications produced by the two lenses:

m = -(d2/f1)(f2/d3)

Here the negative sign indicates that the final image is inverted.

Values and solving the equations simultaneously, we get:

d1 = 38.0 cm

d2 = 6.0 cm

d3 = 42.0 cm

f2 = 14.0 cm

1/f1 = 1/d1 - 1/d2 = 1/38.0 cm - 1/6.0 cm = -0.0263 cm^-1

1/f2 = 1/d2 - 1/d3 = 1/6.0 cm - 1/42.0 cm = 0.1667 cm^-1

m = -(d2/f1)(f2/d3) = -(6.0 cm/(-0.0263 cm^-1))(0.1667 cm^-1/42.0 cm) = 1.53

Using the magnification equation, we can also relate the distances and focal lengths:

m = -f2/f1

Value of m and the given value of f2, we get:

1.53 = -14.0 cm/f1

f1 = -14.0 cm/1.53 = -9.15 cm

Since the focal length of a lens cannot be negative, we take the absolute value and get:

f1 = 9.15 cm

Learn more about focal length visit: brainly.com/question/28039799

#SPJ4