Answer:
587500
Explanation:
Since Wei will still hit every point of the path even though it is irregular, you do not have to worry about the displacement in this problem, just the original path (940m).
W= F x D
587500 = 625N x 940M
what is the formula of percentage uncertainty of volume, and percentage uncertainty of destiny، and percentage uncertainty of mass...
Take into account that for any repeated measurements, the formula of percentage uncertainty is given by the following formula:
[tex]\text{uncertainty}=\frac{half\text{ the range}}{Average\text{ reading}}\cdot100[/tex]Then, for the percentage uncertainty of density. mass and volume, just use the information about half the range and average reading for each magitude (volume, density and mass)
Consider that half the range is one half the subtraction between the maximum and minimum measurement:
[tex]\text{half the range=(max - min)/2}[/tex]the plastic spoon float because the upthrust is more than the weight of the metal spoon so the upthrust pulls it up to float. True OR False
The statement as it has been written in the question is false. This is because, the upthrust must be equal to the weight in order for the object to float.
What is the principle of floatation?The principle of floatation states that an object would float in water when the upthrust on the object is equal to the weight of the object. We know that the upthrust is the force that acts on an object thereby throwing it up. The weight is the force that tries to sink the object into the fluid.
Given the statements above, it is false that; the plastic spoon float because the upthrust is more than the weight of the metal spoon so the upthrust pulls it up to float.
Learn more about upthrust:https://brainly.com/question/24383048
#SPJ1
Which of the following is true when the kinetic energy of the particles in a sample of matter is lowered?The temperature increases.bThe temperature decreases.cThe sample will absorb less heat.dMore heat flows away from the sample.
Answer: The temperature decreases.
The intern energy is shown with the movement of particles, if the lower the speed then the intern energy decrease, and the temperature too.
Answer: More heat flows away from the sample
This one can be true, when they stop moving the heat (temperature) decreases and that heat energy flows away.
Both are so similar, but the most accurate is the temperature decrease because the heat flows a part away not totaly
An electric jug with a power rating of 600W has been used for 6 hours. How many units of energy is used ?
Answer:
w=2160kJ
Explanation:
work=power × Time
w=pt
p=600W
t=60min×60sec=3600
w=600 × 3600
w=2160000joules(J)
w=2160kJ
rate as brainliest
A hollow, spherical shell with mass 2.00 kg rolls without slipping down a 33.0 ∘ slope.
Find the acceleration.
Find the friction force.
The acceleration of the spherical shell is determined as 6.37 m/s².
The friction force is 12.74 N.
What is the coefficient of friction of the surface?
The coefficient of friction of the surface is calculated as follows;
Fsinθ = μFncosθ
where;
F is the applied force on the spherical shellFn is the weight of the spherical shellmg(sin θ) = (μmg) cosθ
(sin θ) = μ cosθ
μ = sinθ/cos θ
where;
g is acceleration due to gravityθ is angle of inclination of the slopeμ = tan θ
μ = tan(33)
μ = 0.65
The acceleration of the spherical shell is calculated as;
a = μg
a = 0.65 x 9.8 m/s²
a = 6.37 m/s²
The frictional force is calculated as follows;
Ff = μmg
Ff = 0.65 x 2 x 9.8
Ff = 12.74 N
Learn more about friction force here: https://brainly.com/question/24338873
#SPJ1
A bicycle and rider going 15 m/s approach a hill. Their total mass is 66 kg.
(a) What is their kinetic energy?
7425 J
(b) If the rider coasts up the hill without pedaling, how high above its starting level will the bicycle be when it finally rolls to a stop?
Need help with B Please help!!
a)The kinetic energy is 7425 J.
b) Theight at which the bicycle starts is 1147 m.
For the given problem, we are dealing with kinetic and potential energy, where Kinetic energy is the energy an object has since its movement. On the off chance that we need to accelerate an object, at that point we must apply a force. Applying a force requires us to do work. After work has been done, energy has been transferred to the object, and the object will be moving with a new constant speed,However when its position is modified from its regular equilibrium position, the bow is able to store energy by virtue of its position. This put-away energy of position is alluded to as potential energy. Potential energy is the stored energy of position had by an object.
Since we were given a mass which is 66 kg and a velocity of 15 m/s
Since the formula of kinetic energy is:
K.E= (1/2)mv², where m is the mass of the object and v is the velocity of the object moving .
= 1/2 (66)(15 m/s)²
=7425 J
For the second part the kinetic energy is converted to the potential energy, so the formula for the potential energy is
P.E = mgh, where m is the mass , g is the acceleration due to gravity and h is the height at which the object.
=7425 J =mgh
=>h= 7425/(mg)
=>h =7425/66*15
=>h =11.47 m
To know more about kinetic energy refer to the link https://brainly.com/question/12669551?referrer=searchResults.
#SPJ1
10. A punter kicks the ball high enough that it spends 5.2 seconds in the air. How fast was it
going when it left his foot?
With the use of first equation of motion, the ball will be going with a velocity of - 51 m/s
What is Velocity ?Velocity is the distance travel in a specific direction per time taken. It is a vector quantity and it is measured in m/s
Given that a punter kicks the ball high enough that it spends 5.2 seconds in the air. To know how fast was it, let us assumed that the initial velocity u of the ball is zero. The ball will be moving under the influence of gravity.
To find the velocity, let us use first equation of motion. That is,
v = u - gt
where
Final velocity v = ?Initial velocity u = 0Acceleration due to gravity g = 9.8 m/s²Time t = 5.2 sSubstitute all the parameters into the equation
v = - 9.8 × 5.2
v = - 50.96 m/s
Therefore, the ball will be going as fast as -51 m/s when it left his foot.
Learn more about Velocity here: https://brainly.com/question/24445340
#SPJ1
A 2300-kg truck is traveling down a highway at 32 m/s. What is the kinetic energy of the truck?
ANSWER:
1177600 joules
STEP-BY-STEP EXPLANATION:
Given:
m = 2300 kg
v = 32 m/s
We can calculate the kinetic energy using the following formula:
[tex]E=\frac{1}{2}m\cdot v^2[/tex]Replacing:
[tex]\begin{gathered} E=\frac{1}{2}\cdot2300\cdot32^2 \\ E=1177600\text{ J} \end{gathered}[/tex]The kinetic energy of the truck is 1177600 joules.
Joe is carrying a load of supplies and likely injuring his back by supporting 882 N of weight. Calculate the mass of what he is carrying.
Since the load Joe is carrying is equal to the supporting weight, the mass of the load will be 90 Kg
What is Weight ?Weight is the gravitational pull of an object under the influence of acceleration due to gravity.
Given that Joe is carrying a load of supplies and likely injuring his back by supporting 882 N of weight.
The load Joe is carrying will be equal to 882 N
To calculate the mass of what he is carrying, let us use the formula
W = mg
Where
Weight W = 882 NAcceleration due to gravity g = 9.8 m/s²Mass m = ?882 = 9.8m
m = 882/9.8
m = 90 Kg
Therefore, the mass of what he is carrying is 90 Kg
Learn more about Weight here: https://brainly.com/question/229459
#SPJ1
A 1800 kg object moving to the east at 13 m/s, collided with a 200 kg object that was moving to the north at 32 m/s. What was the angle of motion
2x6573858493.8404? please
Answer:
13,147,716,987.681
if you multiply 2 by 6573858493.8404, you get 13,147,716,987.681
What is thermodynamics Movement of heatMeasure of heatIt’s magic None of them
To find
What is thermodynamics
Explanation
Thermodynamic study about the transfer of energy to and fro from a system.
Thus thermodynamics is the movement of heat
Conclusion
The correct option is movement of heat
Help I am so confused on what to do with theses steps to get the answer.
Step 1 convert all the dimensions of the box from cm to m
Step 2 calculate the maximum buoyant force if the box was completely submerged. Fb = pfluid V g
Step 3 calculate the Fg of the box Fg = mg
Step 4 Subtract the Fg from the Fb to get the Force of gravity from extra mass
Step 5. Use the Fg from extra mass =mg equation to solve for mass. Using
The buoyant force if the box was completely submerged is 93.84 N.
The length of the box is 40.8 cm.
The height of the box is 10.4 cm and the depth of the box is 19 cm.
Now we know,
1 m = 100 cm
So,
1 cm = 0.01 m
Therefore,
Length, L = 40.8 cm = 40.8 × 0.01 = 0.408 m
Height, H = 10.4 cm = 10.4 × 0.01 = 0.104 m
Depth, D = 19 cm = 19 × 0.01 = 0.19 m
The density of the fluid is 1187 kg/m³.
ρ = 1187 kg/m³ = 1187 × 10³ g/m³
The mass of the box, m = 2325.4 g
The maximum buoyant force will be:
F = ρgV
Here g = 1 g cc
Therefore,
F = 1187 × 1 × ( 0.408 × 0.104 × 0.19 )
F = 93.846590 N
Learn more about buoyant force here:
brainly.com/question/17009786
#SPJ1
What happens when data stored digitally are copied?
OA. Each copy made has worse quality than the original data did.
B. Data are copied quickly, easily, and perfectly.
C. Only one value of the digital data is copied perfectly.
D. Data are copied quickly, but they decrease in quality.
When data stored digitally are copied then data are copied quickly, easily, and perfectly.
Data stored digitally are quickly, easily and perfectly copied.
There is no effect on the quality of the data.It just copies the data exactly as the source and it is same with any other file type. The quality would only decrease if the file is transcoded to a different format or to the same format with a different data stream.Data is a collection of quantities, photos or videos, signs or symbols, on which operations are performed by a computer, which can be stored and transmitted in the form of electrical signals and recorded on magnetic, optical or mechanical recording media.
When you copy (or transfer) a file of any type - JPG or TIFF or RTF or DOC or PSD or whatever, you won't lose any quality.Since no quality of the file is lost, copying a data is an easy, quick and a perfect process.
To know more about Data,
https://brainly.com/question/1427901
#SPJ1
According to the Law of Effect, in which scenario is the behavior likely to be repeated as a result of the reward?
a
An employee is promised a bonus when he leaves his job for each quarter during which he has the most sales.
b
An employee is promised a bonus at the end of the year if he has the most sales for the first quarter.
c
An employee receives a bonus at the end of the quarter for having the most sales for
week one in the quarter.
d
An employee receives a bonus at the end of the week for having the most sales that week.
Answer:
D. An employee receives a bonus at the end of the week for having the most sales that week.
Explanation:
Took the test
A 7 lb bowling ball accelerates at a rate of 7 m/s2.
According to the given statement The new acceleration is 21 m/s².
The correct option is D.
What is an acceleration defined as?Any process where the velocity varies is referred to as acceleration. There are only two ways to speed up: changing your speed or changing your direction, or changing both. This happens because velocity entails both a speed and a direction.
Briefing:The initial force is F = mass x acceleration
F = 3.17515 kg x 7 m/s²
F = 22.23 N
When the net force is tripled, the new acceleration will be
3 x F =m x a'
3 x 22.23 = 3.17515 x a'
a' = 21.003 m/s²
The new acceleration is 21 m/s². The correct option is d.
To know more about Acceleration visit:
https://brainly.com/question/12550364
#SPJ13
The complete question is -
A 7 lb bowling ball accelerates at a rate of 7 m/s². If the net force on the bowling ball is tripled, what will be its new acceleration?
a. 2.3 m/s²
b. 7 m/s²
c. 14 m/s²
d. 21 m/s²
Explain how a $10.00 compact fluorescent light bulb (15 W) can be an overall money saver compared to an incandescent light bulb (60 W) that costs $0.50.
Answer:
Explanation:
We would consider the kilowatt hour for both bulbs. It is the energy consumed by an appliance per hour.
Recall, 1 kw = 1000w
15w = 15/1000 = 0.015 kw
60w = 60/1000 = 0.06kw
In 1 hour,
1)
The 15 W bulb would consume 0.015 kw.
For 10 hours per day, the consumption is 0.015 x 10 = 0.15kw
For a month of 30 days, the consumption is 0.15 x 30 = 4.5
Let's assume that the charge per KW is $0.2
Consumption cost per month = 0.2 x 4.5 = $0.9 per month
2)
The 60 W bulb would consume 0.06 kw.
For 10 hours per day, the consumption is 0.06 x 10 = 0.6kw
For a month of 30 days, the consumption is 0.6 x 30 = 18
Let's assume that the charge per KW is $0.2
Consumption cost per month = 0.2 x 18 = $3.6 per month
Thus, the 15W bulb would be an overall money saver as time goes on.
A car of mass m = 1090 kg is traveling down a θ = 11 degree incline. When the car's speed is v0 = 16 m/s, a mechanical failure causes all four of its brakes to lock. The coefficient of kinetic friction between the tires and road is μk = 0.45.
Calculate the distance the car travels down the hill L in meters until it comes to a stop at the end.
The distance travelled by the car along the plane is 29.56 m.
What is the acceleration of the car down the incline?The acceleration of the car down the incline is calculated by applying Newton's second law of motion as shown below;
F - Ff = ma
where;
F is the applied force on the car = 0Ff is the frictional force acting on the car, trying to stop it m is the mass of the cara is the acceleration of the car down the inclinefrictional force acting on the car, Ff = μmg cosθ
0 - μmg cosθ = ma
-μmg cosθ = ma
-μg cosθ = a
where;
μ is coefficient of kinetic frictionθ is the angle of inclination of the planea = -(0.45 x 9.8 x cos11)
a = -4.33 m/s²
The distance travelled by the car along the plane is calculated as follows;
v² = u² + 2aL
where;
L is the length of the incline = distance travelled by the carv is the final velocity of the car when it stops = 0u is the initial velocity of the car = 16 m/sa is the acceleration of the car0 = (16²) + 2(-4.33)L
0 = 256 - 8.66L
8.66L = 256
L = 256/8.66
L = 29.56 m
Learn more about distance travelled here: https://brainly.com/question/2854969
#SPJ1
. What are the velocities of sound waves in air, helium, and carbon dioxide? Show your data. Which was the fastest? Why do sound waves travel at different speeds in each gas? Explain. Note that the values for helium will be incomplete in these frequency ranges.
Answer:
Taking into account the table we get that, for n = 2, the velocities of sound waves are
Velocity on air: 267.3 m/s
Velocity on helium: 260 m/s
Velocity of carbon dioxide: 829.3 m/s
The velocity of the sound travels at different speeds in each gas because the velocity depends on the properties of the medium like the density. Since the air, helium, and carbon dioxide have different densities, the sound speed will be different.
Suppose a 60.0-kg gymnast climbs a rope. (a) What is the tension in the rope if he climbs at a constant speed? (b) What is the tension in the rope if he accelerates upward at a rate of 1.50 m/s2?
Use the Newton's Second Law of Motion to find the tension in the rope on each case.
a)
Since the gymnast climbs at a constant speed, then the net force acting on the gymnast must be 0. Since there are only two forces acting on the gymnast, namely the tension of the rope and the weight of the gymnast, then:
[tex]\begin{gathered} F_N=T-W=0 \\ \Rightarrow T=W \end{gathered}[/tex]On the other hand, the weight of the gymnast is equal to the product of its mass times the acceleration of gravity, g=9.81m/s^2:
[tex]\begin{gathered} W=mg \\ =(60\operatorname{kg})(9.8\frac{m}{s^2}) \\ =588N \end{gathered}[/tex]Then, the tension of the rope is:
[tex]T=588N[/tex]b)
The forces acting on the gymnast are 2: the tension of the rope and the gravitational pull:
[tex]F_N=T-W[/tex]From the second law of motion, we know that the net force acting over an object of mass m produces an acceleration a given by:
[tex]F_N=ma[/tex]Then:
[tex]\begin{gathered} T-W=ma \\ \Rightarrow T=W+ma \end{gathered}[/tex]Substitute W=588N, m=60kg and a=1.50 m/s^2 to find the tension of the rope:
[tex]\begin{gathered} T=588N+(60\operatorname{kg})(1.5\frac{m}{s^2}) \\ =588N+90N \\ =678N \end{gathered}[/tex]Therefore, the answers are:
[tex]\begin{gathered} a)T=588N \\ b)T=678N \end{gathered}[/tex]A planet has mass M and radius 2R.
a) Derive an expression for the escape speed from the planet.
b) A projectile of mass m is shot directly away from the surface of the planet at ⅓ of the escape
speed from the planet. Derive an expression for the maximum distance from the center of the
planet the projectile reaches, in terms of R. Simplify as far as possible. (Ignore the existence of
all other celestial objects.)
The escape velocity of the planet is [tex]\sqrt{gR\\}\\[/tex] when mass is M and radius is 2R.
In astronomy and space research, escape velocity refers to the speed at which a body can leave a gravitational field without being further accelerated. It is given be the expression ,[tex]v_{e} = \sqrt{2gR}[/tex]
Where, Ve is the escape velocity, g is gravity , and R is the radius of the earth.
If a planet has mass M and radius 2R then an expression for the escape velocity from the planet can be calculated as,
[tex]v_{e} = \sqrt{(2GM)/R[/tex]
Here, G is the gravitational force of the planet therefore Newton's law of gravitational force can be used as,
g = GM/R²
gR²= GM
Thus, with the help of above equations the escape velocity of the planet can be calculated when mass is M and radius is 2R i.e.
[tex]v_{e} = \sqrt{(2GM)/2R[/tex]
[tex]v_{e} = \sqrt{(2GR)/2R[/tex]
[tex]v_{e} = \sqrt{gR[/tex]
Therefore , the escape velocity of planet is equal to the root of gravity g and radius R .
To know more about escape velocity
https://brainly.com/question/13984830
#SPJ1
The diagram shows what happens when a polythene rod is rubbed with a dry cloth. Select the statements that are true
When a polythene rod is rubbed with a dry cloth, the dry cloth loses electrons, the polythene rod gains electrons and the dry cloth is left with positive charge.
The electrons on the dry cloth's surface move to the polyethene rod when it is brushed against a polythene rod. It is considered to be negatively charged because more electrons have accumulated within the polythene rod as a result of the rod being electron rich and the electrons moving there.
The amount of electrons inside the cloth has dropped, making the cloth electron-deficient. It is referred to as positively charged because of this.
To know more about Charging by Rubbing, visit,
https://brainly.com/question/26375737
#SPJ9
While experimenting with electromagnets, students oriented two like you see in the diagram here. Predict what will happen and explain
why.
A The two electromagnets will repel; the poles repel.
B The two electromagnets will repel; the electrical current forces them away from each other.
C The two electromagnets will attract; opposite poles attract
D Nothing will happen; electromagnets do not behave like typical bar magnets.
Answer:
C The two electromagnets will attract; opposite poles attract
Explanation:
Electromagnets behave like regular magnets - they have two poles - positive and negative
Like regular magnets, opposite poles attract, similar poles repel
Calculate the force between charges 4 x 10^-8 C and 1.8 x 10^-6 C if they are 3.5 m apart.
Explanation
Coulomb's law states that the electrical force between two charged objects is directly proportional to the product of the quantity of charge on the objects and inversely proportional to the square of the separation distance between the two objects.
[tex]F=k\frac{q_1\cdot q_2}{r^2}[/tex]where k is the coulomb constant
[tex]k=8.9875\cdot10^9\text{ N }\frac{m^2}{C^2}[/tex]Step 1
let
[tex]\begin{gathered} q_1=4\cdot10^{-8}C \\ q_2=1.8\cdot10^{-6} \\ r=3.5\text{ m} \\ k=8.9875\cdot10^9\text{ N }\frac{m^2}{C^2} \end{gathered}[/tex]now, replace.
[tex]\begin{gathered} F=k\frac{q_1\cdot q_2}{r^2} \\ F=8.9875\cdot10^9\text{ N }\frac{m^2}{C^2}(\frac{4\cdot10^{-8}C\cdot1.8\cdot10^{-6}}{(3.5m)^2}) \\ F=5.2824\cdot10^{-5}\text{ N} \end{gathered}[/tex]I hope this helps you
If F =GMm/R2
What is the dimension of the stress?
What is the unit of frequency?
The dimension of stress is M1 L-1 T-2 and the unit of frequency is Hz.
What is the frequency?
The frequency with which something happens over a specific time frame or sample
Let us find out the dimension of stress.
Stress = Force/Area
Force = mass * acceleration
Stress= M * L * T-2/ L2
Therefore, Stress = M L-1 T-2
As for the second question,
The unit of frequency is Hz (Hertz)
Hence, the dimension of the stress = M L-1 T-2 and the unit of frequency is hertz.
To learn more about the stress dimensions concept Check the given link
https://brainly.com/question/26108464
#SPJ9
You pull a box 23 m horizontally, If the rope tension is 120 N , and if the rope does 2500 J of work on the box, what angle θ does the rope make with the horizontal?
The angle θ made by the rope with the box is equal to 25.17 degrees.
If the rope is pulled at an angle A and the tension in the rope was T, then the rope will have two components of forces,
One Vertical which is TsinA and one along horizontal which is TcosA,
And we know,
W = F.s.cosα
Where,
F is the force applied,
s is the Displacement along force,
α is the angle between them,
We know, the box is moving forward, so the angle between the vertical component of tension and displacement is 90 degrees, so the vertical component of tension will not do any work, and the angle between displacement and the horizontal component is 0 degrees,
So, the work done by the horizontal component is 0 degrees,
So, we cam write,
W = TcosA.D
where D is the displacement of the box, which is given to be 23m,
T is the tension in the string which is 120N,
W is the work done by the rope on the box which is 25000J,
so, putting all the values,
2500 = 120.cosA.23
cosA = 2500/120x23
cos A = 0.9
So, A is 25.17 degrees.
The angle made by the rope is 25.17 degrees,
To know more about, work done, visit,
https://brainly.com/question/25573309
#SPJ1
How do magnification and resolution compare between electron and light microscopes?
magnification and resolution compare between electron and light microscopes by they produce an photograph of a specimen with the aid of using the usage of a beam of electrons instead of a beam of mild.
Electron microscopes range from mild microscopes in that they produce an photograph of a specimen with the aid of using the usage of a beam of electrons instead of a beam of mild. Electrons have a whole lot a shorter wavelength than seen mild, and this lets in electron microscopes to supply higher-decision photos than popular mild microscopes. Electron microscopes may be used to observe now no longer simply complete cells, however additionally the subcellular systems and cubicles inside them.
For more information about microscope click here:
https://brainly.com/question/507443
What is the average velocity of a car driving down the highway if it’s displacement is 123m west during a time period of 14.0s
The average velocity of a car driving down the highway if it’s displacement is 123 m west during a time period of 14.0 s is 8.79 m/sec.
What is Velocity?The rate at which an object's position changes when observed from a specific point of view and when measured against a specific unit of time is known as its velocity. Unit of velocity is m/sec.
Given in the question a car driving down the highway it’s displacement is 123 m west during a time period of 14.0 s then the average velocity is given as,
Average velocity = displacement / time
= 123/14
= 8.79 m/sec
The average velocity of a car driving down the highway if it’s displacement is 123 m west during a time period of 14.0 s is 8.79 m/sec.
To learn more about velocity refer to the link:
brainly.com/question/18084516
#SPJ1
A football punter accelerates a football from rest to a speed of 13 m/s during the time in which his toe is in contact with the ball (about 0.24 s). If the football has a mass of 0.49 kg, what average force does the punter exert on the ball?_____ N
Given:
The initial speed of the football is: vi = 0 m/s (as initially, the football is at rest)
The final speed of the football is: vf = 13 m/s
The time for which the football accelerates is: t = 0.24 s
The mass of the football is: m = 0.49 kg
To find:
The force exerted on the ball
Explanation:
The acceleration of the ball can be determined by using the following equation.
[tex]a=\frac{v_f-v_i}{t}[/tex]Substituting the values in the above equation, we get:
[tex]\begin{gathered} a=\frac{13\text{ m/s}-0\text{ m/s}}{0.24\text{ s}} \\ \\ a=\frac{13\text{ m/s}}{0.24\text{ s}} \\ \\ a=54.17\text{ m/s}^2 \end{gathered}[/tex]The force exerted by the punter on the ball can be determined by using Newton's second law of motion.
According to Newton's second law of motion,
[tex]F=ma[/tex]Substituting the values in the above equation, we get:
[tex]\begin{gathered} F=0.49\text{ kg}\times54.17\text{ m/s}^2 \\ \\ F=26.54\text{ N} \end{gathered}[/tex]Final answer:
The force exerted by the punter on the ball is 26.54 Newtons (N).
Explain the flow of energy needed for the deer to eat.
Energy flow in an needed for the deer to eat starts at the sun which produces all the energy needed for life. Then comes the producers, the autotrophs(plants). These organisms harness the energy of the sun and convert it into sugars. Then deer which eat the autotrophs get the next most energy.
What is energy flow?One of the key components that enables the survival of such a large number of organisms is the energy flow within the ecosystem. Solar energy is the main source of energy for almost all living things on Earth.
It is interesting to learn that less than 50% of the sun's actual radiation reaches Earth. The radiation that plants can use to perform photosynthesis is the radiation that is considered to be effective.
Through the food chain and food web, energy is transferred. Being the energy producers, plants use their chloroplasts to absorb sunlight, part of which is converted into chemical energy during the process of photosynthesis.
Learn more about energy flow
https://brainly.com/question/11413927
#SPJ9