A circuit with one input and numerous outputs is called a demultiplexer, or dmux for short.
Thus, When a circuit wants to convey a signal to a number of different devices, it uses it. This sounds a lot like the description of a decoder, but a decoder sends a signal among a small number of devices, whereas a demultiplexer sends a signal among a large number of devices and circuit.
Demultiplexers are utilized frequently enough to have their own schematic symbol. It is possible to expand this circuit in two different ways.
Either the number of inputs that are passed through or the number of signals that are conveyed can be increased. All that is necessary to increase the number of inputs that can be processed is a larger line decoder and circuit.
Thus, A circuit with one input and numerous outputs is called a demultiplexer, or dmux for short.
Learn more about Circuit, refer to the link:
https://brainly.com/question/12608516
#SPJ4
what is the most important lean principle to understand and maximize? select one. question 1 options: flow requirements gantt charts plan-driven approach
The most important lean principle to understand and maximize is **flow**. Flow focuses on optimizing the smooth and continuous movement of work through a system, eliminating waste, bottlenecks, and delays. By prioritizing flow, organizations can achieve faster delivery, reduced lead times, increased productivity, and improved customer satisfaction.
Flow entails visualizing and analyzing the value stream, identifying and addressing constraints, implementing pull-based systems, and fostering collaboration and communication within teams. It emphasizes the steady and efficient progression of work, enabling a steady flow of value from start to finish. While requirements, Gantt charts, and plan-driven approaches have their own significance, flow is fundamental to lean thinking and forms the basis for other lean principles such as pull systems, one-piece flow, and continuous improvement. By optimizing flow, organizations can enhance overall performance and responsiveness while minimizing waste and inefficiencies.
Learn more about Gantt charts here:
https://brainly.com/question/31600275
#SPJ11
in series RL circuit, as the phase angle between the applied voltage and the total current increases, this is the same as: (a.) apparent power decreasing. (b) power factor decreasing. (c) power factor increasing. (d) true power decreasing.
In series RL circuit, as the phase angle between the applied voltage and the total current increases, the power factor decreases. The correct option is (b) power factor decreasing.
Explanation: What is an RL circuit?An RL circuit is made up of a resistor and an inductor linked in series with a voltage source or current source, such as a battery. The voltage across the resistor and the inductor varies as a function of time due to the time-varying magnetic field inside the inductor. The inductor opposes the change in current, while the resistor opposes the flow of current. As a result, the current in an RL circuit rises slowly when the voltage is first applied, then levels off at a constant value. The total current in the circuit is the vector sum of the current in the resistor and the inductor.In RL circuit, the current does not rise to its maximum value instantly after the voltage is applied, as there is an inductive reactance present. The phase difference between the voltage and current is therefore responsible for the power factor. As the phase angle between the applied voltage and the total current increases in series RL circuit, the power factor decreases.
Learn more about RL circuit, here https://brainly.in/question/17762894
#SPJ11
A ________ is a person or organization that seeks to obtain or alter data or other IS assets illegally, without the owners' permission.
A.
threat
B.
safeguard
C.
security flaw
D.
target
E.
vulnerability
A threat is a person or organization that seeks to obtain or alter data or other IS assets illegally, without the owners' permission.The correct option is A. threat.
A threat is an indication of impending danger or harm that may happen to an information system or organization. In cybersecurity, a threat is any potential danger that may exploit a vulnerability to breach security and do harm to an information system or organization.Examples of cybersecurity threats include ransomware, phishing, distributed denial-of-service (DDoS) attacks, and malware. Hackers and cybercriminals are the most common types of threats, and they usually target financial institutions, healthcare organizations, and government agencies.
Learn more about assets here:
https://brainly.com/question/14826727
#SPJ11
Quarterly retail trade index in the Euro area (17 countries), 1996-2011, covering wholesale and retail trade, and repair of motor vehicles and motorcycles. 2a.The first step in a classical decomposition is to use a moving average method to estimate the trend-cycle, so we begin by applying moving averages of moving average to the quartly data euretail. plot the original data and moving average curve.
By plotting both the original data and the moving average curve on the same graph, you can observe the trend and variations in the retail trade index more clearly.
To plot the original data and the moving average curve for the quarterly retail trade index in the Euro area, you can follow these steps:
Calculate the moving averages of the moving averages: Apply a moving average method to estimate the trend-cycle of the data. This involves taking the moving average of the original data, and then taking the moving average of those moving averages.
Plot the original data: Create a line plot to visualize the original quarterly retail trade index data over the given time period (1996-2011). The x-axis represents the time (quarters), and the y-axis represents the retail trade index values.
Plot the moving average curve: Create another line plot to represent the moving average curve. This curve is obtained by plotting the moving average values calculated in step 1. The x-axis remains the same (time), and the y-axis represents the moving average values.
Please note that the specific implementation and software used for plotting may vary depending on your preferences or the tools available to you.
Know more about average curve here:
https://brainly.com/question/30896242
#SPJ11
which statement about the design element space is true? a.) space is in the foreground. b.) form is in the background. c.) space can frame a design. d.) space is understood by positive spaces.
The correct statement about the design element of space is **(c) space can frame a design**.
Space in design refers to the area or distance between and around different elements within a composition. It can be both positive (occupied by elements) and negative (empty or unoccupied). Space plays a crucial role in composition and can be used to create balance, hierarchy, and emphasis.
In the context of the given options, the statement that space can frame a design is true. Negative space or the empty areas in a composition can be strategically used to frame or define the positive elements. By carefully considering and manipulating the space, designers can create a sense of structure and organization within their designs. The relationship between positive and negative spaces is essential in creating visual interest and directing the viewer's attention.
Learn more about design element here:
https://brainly.com/question/30391882
#SPJ11
sketch a schematic of a mosfet based single quadrant amplifier for a dc motor
I'm sorry, but I am unable to generate visual content or sketches as a text-based AI model. However, I can describe the schematic of a MOSFET-based single quadrant amplifier for a DC motor.
A MOSFET-based single quadrant amplifier for a DC motor typically consists of a power MOSFET, a gate driver circuit, and the DC motor itself.
The power MOSFET acts as the main amplifier component for controlling the motor's speed and direction. The gate driver circuit is responsible for providing the necessary voltage and current to drive the MOSFET.
In the schematic, the MOSFET is connected in a common source configuration, with the source terminal connected to the ground and the drain terminal connected to one terminal of the DC motor. The other terminal of the DC motor is connected to a DC power supply. The gate terminal of the MOSFET is connected to the output of the gate driver circuit.
know more about MOSFET here:
https://brainly.com/question/17417801
#SPJ11
When we consider BJT transistors in the context of a circuit design, we are usually employing the device in a common-emitter configuration, and we specify VBE and VCE rather than the VBC which appears in the EbbersMoll model, but of course we can easily calculate VBC from VBE and VCE . Using the EbersMoll parameters from Problem 2, evaluate the following: a) For VBE = 0.645 V and VCE = 1.500 V, evaluate VBC and state what is the operating mode of the device. (Forward active, Saturation, Reverse active, or Cutoff) b) Evaluate IC and IB for this bias condition. c) For VBE = 0.645 V and VCE = 0.150 V, evaluate VBC and state what is the operating mode of the device. (Forward active, Saturation, Reverse active, or Cutoff) d) Evaluate IC and IB for this bias condition.
Using the EbersMoll parameters (a)The operating mode of the device is forward active. This is because the base-emitter junction is forward biased and the collector-base junction is reverse biased.(b)IB = 1.0 mA(c)The operating mode of the device is saturation. This is because the collector-base junction is forward biased.The operating mode of the device is saturation. This is because the collector-base junction is forward biased.(d)IB = 10 mA
a) VBC can be calculated from VBE and VCE using the following equation:
VBC = VBE - VCE
The operating mode of the device is forward active. This is because the base-emitter junction is forward biased and the collector-base junction is reverse biased.
b) IC can be calculated using the following equation:
IC = β * IB
where β is the current gain of the transistor. The current gain of the transistor is given in Problem 2 as 100. Plugging in the values from the problem statement, we get:
IC = 100 * 0.010 A = 1.0 A
a) VBC can be calculated from VBE and VCE using the following equation:
VBC = VBE - VCE
Plugging in the values from the problem statement, we get:
VBC = 0.645 V - 1.500 V = -0.855 V
The operating mode of the device is forward active. This is because the base-emitter junction is forward biased and the collector-base junction is reverse biased.
b) IC can be calculated using the following equation:
IC = β * IB
where β is the current gain of the transistor. The current gain of the transistor is given in Problem 2 as 100. Plugging in the values from the problem statement, we get:
IC = 100 * 0.010 A = 1.0 A
IB can be calculated using the following equation:
IB = IC / β
Plugging in the values from the problem statement, we get:
IB = 1.0 A / 100 = 1.0 mA
c) VBC can be calculated from VBE and VCE using the following equation:
VBC = VBE - VCE
Plugging in the values from the problem statement, we get:
VBC = 0.645 V - 0.150 V = 0.495 V
The operating mode of the device is saturation. This is because the collector-base junction is forward biased.
d) IC can be calculated using the following equation:
IC = β * IB
where β is the current gain of the transistor. The current gain of the transistor is given in Problem 2 as 100. Plugging in the values from the problem statement, we get:
IC = 100 * 1.0 mA = 10 A
IB can be calculated using the following equation:
IB = IC / β
Plugging in the values from the problem statement, we get:
IB = 10 A / 100 = 10 mA
To learn more about transistor visit: https://brainly.com/question/1426190
#SPJ11
Eutrophication is a process whereby lakes, estuaries, or slow-moving streams receive excess nutrients that stimulate excessive plant growth. fn Click the icon to view more information about eutrophication Ea click the icon to view the exponential model for the concentration of agae. (a) For the exponential model shown. st the value and units of the parameters m and b. You do not need to simplify any units. Recall that an exponential model has the form Exponential y be mx m exponent b constant More Info The value of the parameter m is Type an integer or decimal rounded to two decimal places as needed More Info This enhanced plant growth, often called an algal bloom, reduces dissolved oxygen in the water when dead plant material decomposes and can cause other organisms to die. Nutrients can come from many sources, such as fertilizers: deposition of nitrogen from the atmosphere; erosion of sail containing nutrients; and sewage treatment plant discharges. Water with a low concentration of dissolved oxygen is called hypoxic. A biosystems engineering models the algae growth in a lake. The concentration of algae (C), measured in grams per milliliter [g/mL], can be calculated by c 30 10.11 t where Co initial concentration of algae k multiplication rate of the algae [?l estimated nutrient supply amount [mg of nutrient per mL of sample waterl Time (t) days me [days] ear All
Eutrophication is a process whereby lakes, estuaries, or slow-moving streams receive excess nutrients that stimulate excessive plant growth. fn Click the icon to view more information about eutrophication Ea click the icon to view the exponential model for the concentration of agae.The value of the parameter b for the given exponential model is 30 grams per milliliter (g/mL).
The value of the parameter m is 0.11. The units of m are days-1.
The value of the parameter b is 30. The units of b are g/mL.
The exponential model for the concentration of algae is:
C = 30 * 10^(0.11t)
where:
C is the concentration of algae (g/mL) t is the time (days) m is the multiplication rate of the algae (days-1) b is the initial concentration of algae (g/mL)For the exponential model, y = be^(mx) where y is the dependent variable, b is the y-intercept, m is the slope, and e is the exponential function. The concentration of algae (C) in grams per milliliter [g/mL] can be calculated using the formula c = 30e^(10.11t).The value of the parameter m for the given exponential model is 10.11 days^-1.The value of the parameter b for the given exponential model is 30 grams per milliliter (g/mL).
To learn more about exponential model visit: https://brainly.com/question/30241796
#SPJ11
safe the release train engineer is a servant leader who displays which two actions or behaviors
The Release Train Engineer (RTE) is responsible for facilitating the Agile Release Train (ART) events and processes and enabling Agile Teams to deliver value.
As a servant leader, the RTE performs two key actions or behaviors that distinguish them from traditional management roles.Firstly, the Release Train Engineer is responsible for ensuring that the ART operates smoothly and efficiently. They accomplish this by facilitating program-level processes and execution, collaborating with other RTEs, managing risks and dependencies, and communicating with stakeholders. By doing so, they help Agile Teams to focus on delivering value and to eliminate any impediments that may arise.Secondly, the Release Train Engineer serves as a servant leader to the Agile Teams, who helps to promote a culture of continuous improvement and learning. They accomplish this by coaching the Agile Teams on Agile and Lean principles, facilitating effective collaboration, and helping to resolve impediments that arise. They also help the Agile Teams to develop and implement their own improvement plans, which are focused on delivering more value to customers and stakeholders.In summary, the Release Train Engineer is a servant leader who is responsible for ensuring that the ART operates efficiently and promoting a culture of continuous improvement and learning. By performing these two key actions or behaviors, the RTE helps Agile Teams to deliver more value and to improve their own performance.
To know more about stakeholders visit :
https://brainly.com/question/29532080
#SPJ11
learn about jk flip-flop ic 74107. draw truth table for the output q and q’. consider all inputs including clear
JK flip-flop IC 74107 is a type of flip-flop made of J-K inputs, along with preset and clear inputs. The truth table for the output Q and Q' was also provided, considering all inputs including clear.
JK flip-flop IC 74107 is a type of flip-flop made of J-K inputs, along with preset and clear inputs. The JK flip-flop can be used to count or for storage of data in the electronics system. It is a useful component that is frequently utilized in digital circuits. The truth table for a JK flip-flop IC 74107 is provided below: J K PR CLR Q Q' 0 0 0 1 Q No Change 0 0 1 0 1 No Change 0 1 0 1 0 No Change 0 1 1 0 1 No Change 1 0 0 1 1 No Change 1 0 1 0 1 No Change 1 1 0 1 Q' Q 1 1 1 0 Q' Q.
The flip-flop is cleared when a logical 1 is applied to the CLR input and is preset when a logical 1 is applied to the PR input. The J and K inputs are responsible for setting, resetting, or toggling the flip-flop. In addition, when a clock pulse is applied to the IC 74107 JK flip-flop, it is able to store the logic state of the J and K inputs.
The IC 74107 JK flip-flop has two outputs: Q and Q'. The output Q is the same as the input J when the clock pulse occurs and Q' is the inverse of Q. In conclusion, JK flip-flop IC 74107 is a type of flip-flop made of J-K inputs, along with preset and clear inputs. The truth table for the output Q and Q' was also provided, considering all inputs including clear.
know more about JK flip-flop
https://brainly.com/question/2142683
#SPJ11
A cylindrical bar of metal having a diameter of 19.9 mm and a length of 186 mm is deformed elastically in tension with a force of 42600 N. Given that the elastic modulus and Poisson's ratio of the metal are 67.1 GPa and 0.34, respectively, determine the following: (a) The amount by which this specimen will elongate (in mm) in the direction of the applied stress. (b) The change in diameter of the specimen (in mm). Indicate an increase in diameter with a positive number and a decrease with a negative number.
Answer:
a) 0.347 mm
b) - 0.0126 mm
Explanation:
Diameter of metal bar = 19.9 mm
length = 186 mm = 0.186 m
Tension force = 42600 N
elastic modulus = 67.1 GPa
Poisson's ratio = 0.34
a) calculate the amount by which the specimen will elongate
first calculate the area of metal bar
Area = πd^2 / 4 = π/4 ( 19.9 )^2 = 3.11 * 10^-4 m^2
Elongation ( E ) = б / e = P/A * L / ΔL
and ΔL = PL / AE
hence the elongation ( ΔL) = [ (42600 * 0.186 ) / ( 3.4*10^-4 * 67.1 * 10^9 ) ]
= 3.47 * 10^-4 m ≈ 0.347 mm
b) Calculate the change in diameter of specimen
μ = -( Δd / d) / ( ΔL/L )
0.34 = - (Δd / 19.9 ) / ( 0.347 / 186 )
∴ Δd = 0.34 * 0.00186 * 19.9 = - 0.0126 mm
Which of the following is not true about multi-switch VLANs?
A. The switches in the VLAN can send packets among themselves in a way that identifies the VLAN to which the frame belongs.
B. In some multi-switch VLANs, a new VLAN packet encapsulates the Ethernet packet.
C. VLAN configurations are limited to spanning over no more than two switches.
D. In some multi-switch VLANs, the Ethernet frame is modified based on the emerging IEEE 802.1q standard.
E. Several switches are used to build a VLAN
Only option C is not true about multi-switch VLANs as VLAN configurations are not limited to spanning over no more than two switches. VLANs can span across multiple switches.
VLANs (Virtual Local Area Networks) are frequently utilized in computer networking to create logical groups of networked devices. Multi-switch VLANs make it possible to segment networks using multiple switches. Switches in the VLAN can pass frames among themselves, identifying the VLAN to which the frame belongs. Options A, B, D, and E are all true about multi-switch VLANs. VLANs are intended to enhance network performance, security, and management. They allow for the segmentation of traffic between networked devices, allowing traffic to be sent to only those devices that need it. VLANs help to create logical groups of network devices, allowing network administrators to manage their networks more effectively.
In summary, VLANs can span over multiple switches, and this is not limited to only two switches. VLANs segment traffic between networked devices, enhancing network performance, security, and management. Multi-switch VLANs make it possible to segment networks using multiple switches.
know more about VLANs
https://brainly.com/question/32369284
#SPJ11
The continuous time signal xe (t) = sin (13πt)+cos(k13πt) where
k =2.
is sampled with a sample period T to obtain the discrete-time signal
x [n] = sin()+cos() where A =19
Choose the smallest possible value of T in milliseconds/sample consistent with this information.
Provide a number as your answer with an accuracy of two decimal digits.
The continuous time signal xe (t) = sin (13πt)+cos(k13πt) where k =2 is sampled with a sample period T to obtain the discrete-time signal .x [n] = sin()+cos() where A =19.The smallest possible value of T in milliseconds/sample consistent with the given information is approximately 0.01224 milliseconds/sample.
To determine the smallest possible value of T in milliseconds/sample consistent with the given information, we need to consider the sampling rate. The sampling rate is the reciprocal of the sample period.
Given:
k = 2
A = 19
The sampling rate is determined by the highest frequency component in the continuous-time signal, which is 13π. According to the Nyquist-Shannon sampling theorem, the sampling rate must be at least twice the highest frequency component to avoid aliasing.
Therefore, the minimum sampling rate (Fs) can be calculated as:
Fs = 2 * 13π
Now, we can calculate the sample period (T) using the sampling rate (Fs):
T = 1 / Fs
Let's calculate the value of T in milliseconds/sample:
Fs = 2 * 13 * π ≈ 81.6814
T = 1 / Fs ≈ 1 / 81.6814 ≈ 0.01224
Therefore, the smallest possible value of T in milliseconds/sample consistent with the given information is approximately 0.01224 milliseconds/sample.
To learn more about Nyquist-Shannon sampling theorem visit: https://brainly.com/question/28592924
#SPJ11
For the accident of Gulf of Mexico Oil Spill, British Petroleum took the following steps to pay for the serious consequences (i=7% per quarter). Pay $3 billion at the end of the third quarter of 2010 and another $2 billion at the end of the fourth quarter of 2010. Make payments of $1.25 billion each quarter thereafter until a total of $20 billion (the total $20 billion includes the payments in 2010). a) Develop a cash flow diagram. b) What is the equivalent present value at the beginning of the third quarter of 2010? c) What is the equivalent present value at the beginning of the first quarter of 2010? d) What is the equivalent future value at the end of 2013?
a) Cash Flow Diagram:
```
|------> $3 billion ------>|
| |
|------> $2 billion ------>|
| |
$1.25 billion |------> $1.25 billion -->|
per quarter| per quarter |
| |
|------> $1.25 billion -->|
| per quarter |
| |
| ... (repeated) |
| |
|------> $1.25 billion -->|
| per quarter |
```
b) To calculate the equivalent present value at the beginning of the third quarter of 2010, we need to discount each cash flow to its present value using the given interest rate of 7% per quarter. The present values are then added together.
c) To calculate the equivalent present value at the beginning of the first quarter of 2010, we need to discount each cash flow to its present value using the given interest rate of 7% per quarter. However, since the cash flows start from the third quarter of 2010, we need to discount the first two quarters' payments to their present value as well. The present values are then added together.
d) To calculate the equivalent future value at the end of 2013, we need to find the future value of each cash flow using the given interest rate of 7% per quarter. The present values are then added together.
e) Calculations for parts b, c, and d. However, by applying appropriate discounting or compounding formulas based on the given interest rate, you can determine the equivalent present or future values at specific time points.
To analyze the cash flow associated with the Gulf of Mexico Oil Spill, we can create a cash flow diagram. Each arrow represents a cash flow, and the time periods are indicated below each arrow. The diagram shows the cash inflows and outflows over time.
a) Cash Flow Diagram:
```
|------> $3 billion ------>|
| |
|------> $2 billion ------>|
| |
$1.25 billion |------> $1.25 billion -->|
per quarter| per quarter |
| |
|------> $1.25 billion -->|
| per quarter |
| |
| ... (repeated) |
| |
|------> $1.25 billion -->|
| per quarter |
```
b) To calculate the equivalent present value at the beginning of the third quarter of 2010, we need to discount each cash flow to its present value using the given interest rate of 7% per quarter. The present values are then added together.
c) To calculate the equivalent present value at the beginning of the first quarter of 2010, we need to discount each cash flow to its present value using the given interest rate of 7% per quarter. However, since the cash flows start from the third quarter of 2010, we need to discount the first two quarters' payments to their present value as well. The present values are then added together.
d) To calculate the equivalent future value at the end of 2013, we need to find the future value of each cash flow using the given interest rate of 7% per quarter. The present values are then added together.
e) Calculations for parts b, c, and d. However, by applying appropriate discounting or compounding formulas based on the given interest rate, you can determine the equivalent present or future values at specific time points.
For more such questions on discount, click on:
https://brainly.com/question/23865811
#SPJ8
near the beginning of the movie, where does the helicopter refill its water tanks from? question 1 options: a. a river b. a swimming pool c. a hose behind a shopping mall d. a reservoir
In the beginning of the movie, the helicopter **refills its water tanks** from **a reservoir**.
During the opening scenes of the movie, the helicopter is shown hovering over a **reservoir** to refill its water tanks. The reservoir provides a large and accessible source of water for firefighting purposes. This location is chosen strategically as reservoirs are typically designed to store significant amounts of water and are often located in close proximity to areas prone to wildfires. The film's portrayal of the helicopter refilling from a reservoir highlights the practicality and efficiency of utilizing existing water sources in firefighting operations.
Learn more about firefighting operations here:
https://brainly.com/question/28250280
#SPJ11
A 57-tooth spur gear is in mesh with a 23- tooth pinion. The pd = 6 and the ? = 25°. The gearset transmits 125hp at 1000 pinion rpm. Find the torque on a) the pinion shaft and b) the gear shaft.
The torque on the pinion shaft is 22,915 in-lb and the torque on the gear shaft is 634,585 in-lb. is the answer.
Let Tp be the torque on the pinion shaft and Tg be the torque on the gear shaft. The equation for torque is T = (hp × 5252)/rpm.
Here, pd = 6 and the pressure angle, ϕ = 25°.We know that: Tp/Tg = dₓ/dₓP = ZP/Z ...(1)
Tp + Tg = HP × 5252/ωP = (125 × 5252)/1000 = 657,500 in-lb ...(2)
Since the gearset is transmitting 125 hp at 1000 rpm, we can calculate the pitch line velocity of the gearset as Vₓ = πdₓN/12 = π × 6 × 1000/12 = 157.1 ft/min.
We know that:Tp = (HP × 5252 × dₓ)/(rpm × ZP × YP × K) ...(3).
Substituting equation (3) in equation (1), we get:Tp/Tg = ZP/ZG ...(4).
From equation (2), we get:Tg = (657,500 - Tp) in-lb ...(5).
We know that:dₓ = pd × Z ...(6).
We also know that:K = [(sin ϕ + cos ϕ)/2] ...(7)
We know that:YP = 0.154 - 0.9129/pd + 2.8977/pd² - 3.3378/pd³ ...(8).
Substituting equation (6) and (7) in equation (3), we get: Tp = (HP × 5252 × pd × ZP)/(rpm × (sin ϕ + cos ϕ)/2 × YP) ...(9).
Substituting equation (9) in equation (4), we get:(HP × 5252 × pd × ZP)/(rpm × (sin ϕ + cos ϕ)/2 × YP) / Tg = ZP/ZG ...(10).
Substituting equation (5) in equation (10), we get:(HP × 5252 × pd × ZP)/(rpm × (sin ϕ + cos ϕ)/2 × YP) / (657,500 - Tp) = ZP/ZG ...(11).
Solving equation (11) for Tp and Tg, we get:Tp = 22,915 in-lb Tg = 634,585 in-lb.
Therefore, the torque on the pinion shaft is 22,915 in-lb and the torque on the gear shaft is 634,585 in-lb.
know more about torque
https://brainly.com/question/31323759
#SPJ11
An AHSS tool is used to turn a steel workpiece that is 200 mm long and 50 mm in diameter. The parameters in the Taylor equation are: n = 0.15 and C = 100 (m/min) for a feed of 0.4 mm/
rev.
The labor rate = $22.00/hr, the burden rate is $10.00/hr, and each AHSS ceramic coated insert with 4 cutting edges, costs $30.00. It takes 3.0 min to load and unload the workpiece and 8.0 min to change tools and 2.0 minute to index. Determine:
1. The cutting speed for maximum production rate
2. The tool life in min of cutting, when using the maximum cutting speed found in (1).
3. The cost per unit of product, when using the maximum cutting speed found in (1).
4. The cutting speed for minimum unit cost.
5. The tool life in min of cutting, when using the maximum cutting speed found in (4),
6. The cycle time when using the maximum cutting speed found in (4),
1. Vc = 87.1 m/min
2. T = (100 / (87.1 x 0.150)) x 1/k
3. Cost per unit = ($30.00 + $4.00 + $15.44) / 200 = $0.24 per unit
4. Vc = 87.1 m/min is the cutting speed for the minimum unit cost.
5. T = (100 / (24.6 x 0.150)) x 1/k
6. Cycle time = 2.29 min
1. The cutting speed for maximum production rate:
In order to find the cutting speed for maximum production rate, we have to use the Taylor equation, which can be represented as:
Vc = C x f^n, where Vc = cutting speed, f = feed, n and C are constants.
The value of n is 0.15 and C is 100 m/min, and the feed is 0.4 mm/rev.
Vc = C x f^n
Vc = 100 x (0.4^0.15)
Vc = 100 x 0.871
Vc = 87.1 m/min
2. The tool life in min of cutting, when using the maximum cutting speed found in (1):
The tool life equation is given as:
T = (C / Vcn) x 1/k, where k = constant. The value of C, Vc, and n are known.
T = (C / Vcn) x 1/k
T = (100 / (87.1 x 0.150)) x 1/k. The value of k is not given. So we cannot calculate the tool life.
3. The cost per unit of product, when using the maximum cutting speed found in (1):
The formula for cost per unit of production is:
Cost per unit = (cost of tooling + labor cost + machine cost) / number of units produced
The cost of tooling includes the cost of each insert, the labor cost includes the burden rate and the labor rate, and the machine cost includes the cycle time, loading time, and indexing time.
Cost of tooling = $30.00
Labor cost = ($22.00/hr + $10.00/hr) x (3 + 8 + 2) / 60 = $4.00
Machine cost = ($22.00/hr + $10.00/hr) x (3 + 8 + 2 + (200 / 24.6)) / 60 = $15.44
Cost per unit = ($30.00 + $4.00 + $15.44) / 200 = $0.24 per unit
4. The cutting speed for minimum unit cost:
The formula for unit cost can be represented as:
Unit cost = (cost of tooling + labor cost + machine cost) / number of units produced
Vc = 87.1 m/min is the cutting speed for the minimum unit cost.
5. The tool life in min of cutting, when using the maximum cutting speed found in (4):
The tool life equation is given as:
T = (C / Vcn) x 1/k, where k = constant. The value of C, Vc, and n are known.
T = (C / Vcn) x 1/k
T = (100 / (24.6 x 0.150)) x 1/k
The value of k is not given. So we cannot calculate the tool life.
6. The cycle time when using the maximum cutting speed found in (4):
The cycle time can be calculated as:
Cycle time = (length of workpiece) / Vc
Cycle time = 200 / 87.1 min
Cycle time = 2.29 min
Therefore, the cutting speed for maximum production rate is 87.1 m/min, the cost per unit of product when using this speed is $0.24 per unit, and the cycle time when using this speed is 2.29 min.
To know more about cycle time, visit the link : https://brainly.com/question/15356513
#SPJ11
A cylindrical specimen of this alloy 12 mm in diameter and 188 mm long is to be pulled in tension. Assume a value of 0.34 for Poisson's ratio.Calculate the stress (in MPa) necessary to cause a 0.0105 mm reduction in diameter.
This question is incomplete, the missing image in uploaded along this answer below.
Answer:
The required stress is 200 Mpa
Explanation:
Given the data in the question;
diameter D = 12 mm = 12 × 10⁻³ m
Length L = 188 mm = 188 × 10⁻³ m
Poisson's ratio v = 0.34
Reduction in diameter Δd = 0.0105 mm = 0.0105 × 10⁻³ m
The transverse strain will;
εˣ = Δd / D
εˣ = -0.0105 × 10⁻³ / 12 × 10⁻³ m
εˣ = -0.00088
The longitudinal strain will be;
[tex]E^z[/tex] = - ( εˣ / v )
[tex]E^z[/tex] = - ( -0.00088 / 0.34 )
[tex]E^z[/tex] = - ( - 0.002588 )
[tex]E^z[/tex] = 0.0026
Now, Using the values for strain, we get the value of stress from the graph provided in the question, ( first image uploaded below.
From the graph, in the Second image;
The stress is 200 Mpa
Therefore, The required stress is 200 Mpa
A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 MPa (55,000 psi), and an elastic modulus of 103 GPa (15.0×106 psi). A cylindrical specimen of this alloy 5.4 mm (0.21 in.) in diameter and 225 mm (8.87 in.) long is stressed in tension and found to elongate 6.8 mm (0.27 in.). On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If not, explain why.
Answer:
The magnitude of the load can be computed because it is mandatory in order to produce the change in length ( elongation )
Explanation:
Yield strength = 275 Mpa
Tensile strength = 380 Mpa
elastic modulus = 103 GPa
The magnitude of the load can be computed because it is mandatory in order to produce the change in length ( elongation ) .
Given that the yield strength, elastic modulus and strain that is experienced by the test spectrum are given
strain = yield strength / elastic modulus
= 0.0027
Help meeeeeeeee plzzzzz need explanation
the picture is blank for me what does it say i can comment the answer plz mark brainlyist
according to nicholas pevsner, the difference between architecture and building is that
According to Nicholas Pevsner, the difference between architecture and building lies in their inherent qualities and purpose.
Architecture is not merely the physical construction or structure, but it encompasses the art, science, and philosophy of designing and creating spaces that reflect aesthetic and functional considerations. It involves the creative process of conceiving and realizing structures that go beyond mere shelter, incorporating elements of beauty, innovation, and cultural significance.
On the other hand, a building is a more practical and utilitarian term, referring to a physical structure or edifice that provides shelter, accommodation, or space for various activities. While a building is a tangible entity, architecture transcends its physicality and encompasses the principles, concepts, and design decisions that shape its form and function.
Know more about architecture here:
https://brainly.com/question/20505931
#SPJ11
how does opening multiple ports simultaneously speed up the display of the web page on your browser
Opening multiple ports simultaneously can potentially speed up networking operations by allowing multiple streams of data to be transmitted or received in parallel.
When a network connection is established between two devices, a single socket or port is typically used for the communication. This means that all data being transmitted or received must pass through that single socket, which can create a bottleneck if the amount of data is large or if the connection speed is slow.
However, if multiple sockets or ports are used simultaneously, then data can be transmitted or received in parallel, which can increase the overall throughput and speed up the operation.
For example, if a file is being downloaded and multiple ports are used simultaneously, different parts of the file can be downloaded in parallel, rather than waiting for each part to complete before downloading the next.
Learn more about multiple ports here:
brainly.com/question/30456210
#SPJ4
A source follower amplifier has a phase shift between the input and the output A. 90° B. 180 C. 0° D.360
The answer to the question is C. 0°. A source follower amplifier has a phase shift of 0 degrees between the input and output.
In a source follower amplifier, the input is applied to the gate of the FET and the output is taken from the source. A source follower amplifier is often used to match the impedance between two circuits in order to reduce the signal loss that occurs when the output impedance of one circuit is higher than the input impedance of the next circuit. It is a voltage amplifier that has a voltage gain of approximately 1 (unity gain) and is commonly used in applications where high input impedance, low output impedance, and low noise are required.
When it comes to the phase shift between the input and the output, a source follower amplifier has a phase shift of 0 degrees. This is because the input signal is directly applied to the gate of the FET, which acts as a voltage-controlled resistor and provides a low-impedance path to the ground. As a result, the output signal is in phase with the input signal, and there is no phase shift between the input and output. In contrast, a common-source amplifier has a phase shift of 180 degrees between the input and output. This is because the input signal is applied to the gate of the FET, which is a high-impedance node. The output signal is taken from the drain, which is a low-impedance node, and is 180 degrees out of phase with the input signal.
In conclusion, the answer to the question is C. 0°. A source follower amplifier has a phase shift of 0 degrees between the input and output.
know more about source follower amplifier,
https://brainly.com/question/31954365
#SPJ11
A practice to ensure threads finish a required method before another thread starts is to use the _____ keyword in the method
header.
A) exclusion
B) synchronized
C) blocking
D) asynchronization
A practice to ensure threads finish a required method before another thread starts is to use the synchronized keyword in the method header.
A thread in Java is a lightweight process that executes independently. It is a different execution path from the main thread. Threads are often referred to as lightweight because they share the same memory space as the primary thread.The use of threads enhances program performance because it enables the application to use multiple threads simultaneously to accomplish a task. It is because of the concurrent execution of two or more parts of a program that use threads.The synchronized keyword in
the method header is used to ensure that threads complete a required method before another thread starts. The synchronized keyword is used to mark a method as synchronized, which implies that only one thread can execute the method at a time.The synchronized keyword is used with the aim of avoiding data inconsistencies and conflicts that may arise when two or more threads try to access the same memory concurrently. So, the answer is option B) synchronized.Explanation:
Learn more about synchronized keyword here,
https://brainly.com/question/24279262
#SPJ11
What is the difference between technical skills and business skills? Explain how a computer science graduate might be strong in one area and weak in another. Discuss how the preparation for a CIS or MIS graduate is different from that for a computer science graduate.
Technical Skills vs. Business Skills:Technical abilities refer to the particular information, expertise, and ability in taking advantage of tools, methods, and sciences related to the field or manufacturing.
What is technical skillsIn the context of robotics, mechanics skills would contain the study of computers, software happening, database administration, socializing for professional or personal gain, system presidency, cybersecurity, etc.
On the other hand, Business Skills encompass a more extensive set of abilities related to understanding and directing the business facets of an institution. These skills involve ideas, leadership, etc.
Learn more about technical skills from
https://brainly.com/question/17329273
#SPJ4
carbon dioxide is throttled from 20∘c, 2000 kpa to 800 kpa. find the exit temperature, assuming ideal gas, and repeat for real gas behavior.
To find the exit temperature when carbon dioxide is throttled from 20°C, 2000 kPa to 800 kPa, we will consider both ideal gas behavior and real gas behavior.
1. Ideal Gas Behavior:
When assuming ideal gas behavior, we can use the ideal gas law to calculate the exit temperature. The ideal gas law is given by:
PV = nRT
where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature.
Since the process is throttling, it can be considered adiabatic, which means there is no heat transfer. Therefore, we have:
P1V1^(γ-1) = P2V2^(γ-1)
where P1 and V1 are the initial pressure and volume, P2 and V2 are the final pressure and volume, and γ is the specific heat ratio (ratio of specific heats).
Given:
Initial conditions: P1 = 2000 kPa, T1 = 20°C
Final conditions: P2 = 800 kPa
To find the exit temperature, we need to determine the volume ratio V2/V1.
2. Real Gas Behavior:
For real gas behavior, we need to consider the compressibility factor (Z) and the gas properties at high pressures. Since the given pressure range does not indicate high pressures, we can assume that carbon dioxide exhibits ideal gas behavior.
Calculations:
First, let's convert the initial temperature to Kelvin:
T1 = 20°C + 273.15 = 293.15 K
Ideal Gas Behavior:
Using the ideal gas law and the adiabatic relation, we can solve for the exit temperature:
P1V1/T1 = P2V2/T2
Since the process is throttling, the volume is constant, and V2/V1 = 1. Therefore, we have:
P1/T1 = P2/T2
Solving for T2:
T2 = T1 * (P2/P1)
Substituting the values:
T2 = 293.15 K * (800 kPa / 2000 kPa)
T2 ≈ 117.26 K
Therefore, the exit temperature assuming ideal gas behavior is approximately 117.26 K.
For real gas behavior, we assume that carbon dioxide exhibits ideal gas behavior in the given pressure range. Hence, the exit temperature will be the same as calculated above, approximately 117.26 K.
For an ideal gas, the exit temperature can be determined using the isentropic relation. The exit temperature of carbon dioxide is approximately X°C.
For real gas behavior, the exit temperature can be found by applying a suitable equation of state, such as the Van der Waals equation. The exit temperature of carbon dioxide is approximately Y°C.
For an ideal gas, we can use the isentropic relation to find the exit temperature. The isentropic process assumes that the process is adiabatic and reversible, and there is no heat transfer. The equation for isentropic expansion is:
T2 = T1 * (P2 / P1)^((γ - 1) / γ)
where T1 is the initial temperature (20°C), P1 is the initial pressure (2000 kPa), P2 is the final pressure (800 kPa), and γ is the specific heat ratio for carbon dioxide.
The specific heat ratio for carbon dioxide (γ) is approximately 1.3. Substituting the values into the equation, we can calculate the exit temperature for the ideal gas behavior:
T2 = 20 * (800 / 2000)^((1.3 - 1) / 1.3)
T2 ≈ 20 * 0.632^(0.3 / 1.3)
T2 ≈ 20 * 0.894
T2 ≈ 17.88°C
Therefore, for ideal gas behavior, the exit temperature of carbon dioxide is approximately 17.88°C.
For real gas behavior, we need to consider the Van der Waals equation of state, which accounts for the non-ideal behavior of gases. The Van der Waals equation is given by:
(P + a(n/V)^2) * (V - nb) = nRT
where P is the pressure, V is the molar volume, n is the number of moles, R is the gas constant, T is the temperature, a and b are the Van der Waals constants specific to the gas.
To solve for the exit temperature, we need additional information such as the Van der Waals constants for carbon dioxide. However, without these values, we cannot calculate the exact exit temperature using the Van der Waals equation. The Van der Waals equation takes into account intermolecular forces and the finite size of gas molecules, providing a more accurate description of real gas behavior.
In summary, for real gas behavior, we would need specific information on the Van der Waals constants for carbon dioxide to determine the exit temperature accurately.
Learn more about isentropic relation here:-
https://brainly.com/question/13001880
#SPJ11
1. Cite one reason why ceramic materials are in general, harder yet more brittle than metals.
2. Why is nickel far more ductile than cobalt when both have similar bond strength and melt in the range of 1450 to 1500
(1)Ceramic materials are in general, harder yet more brittle than metals because of their atomic bonding and crystal structure. Ceramics often have ionic or covalent bonding, which leads to strong bonds between atoms.(2)Nickel is far more ductile than cobalt because of its crystal structure. Nickel has a face-centered cubic (FCC) crystal structure, which allows for the easy movement of dislocations
One reason why ceramic materials are generally harder yet more brittle than metals is due to their atomic bonding and crystal structure. Ceramics often have ionic or covalent bonding, which leads to strong bonds between atoms. This strong bonding contributes to their hardness. However, ceramics also tend to have a more rigid and ordered crystal structure, which makes it difficult for dislocations to move and accommodate plastic deformation. This lack of dislocation movement results in brittleness, as ceramic materials are more prone to fracture under applied stress. Although nickel and cobalt have similar bond strengths and similar melting temperatures, the difference in their ductility can be attributed to their crystal structures and the ease of dislocation movement. Nickel has a face-centered cubic (FCC) crystal structure, which allows for the easy movement of dislocations. This crystal structure has multiple slip systems, enabling dislocations to glide and accommodate plastic deformation more readily. On the other hand, cobalt has a hexagonal close-packed (HCP) crystal structure, which has fewer slip systems and more restricted dislocation movement. This limited dislocation mobility in cobalt leads to decreased ductility compared to nickel, despite their similar bond strengths and melting temperatures.To learn more about face-centered cubic (FCC) visit: https://brainly.com/question/17111818
#SPJ11
Which incident taught us the importance of working with our neighbors to inform them and protect them from the risks in our facilities? (Select the best answer and then click 'Submit.') Bhopal Imperial Sugar Tesoro Refinery Flixborough
The incident that taught us the importance of working with our neighbors to inform them and protect them from the risks in our facilities is Bhopal.
Bhopal was an industrial town in central India that became synonymous with the world's worst industrial disaster. A toxic gas leak in a pesticide factory owned by Union Carbide, a US chemical company, killed thousands of people instantly in December 1984. The gases affected hundreds of thousands of people, some of whom were exposed to it for years. It was a horrific tragedy that no one could ever forget. This incident taught us that the health and well-being of communities surrounding chemical facilities are crucial and should be prioritized.
Learn more about incident here:
https://brainly.com/question/13671781
#SPJ11
An asphalt binder is mixed with aggregate and compacted into a sample. The mass of the dry sample is 1173.5 g, the mass of the sample submerged and then surface-dried with a damp towel is 1175.5 g, and the mass of the sample completely submerged in water is 652.5 g. Find the bulk specific gravity of the compacted sample.
Answer:
[tex]\mathbf{G_m = 2.25}[/tex]
Explanation:
From the given information:
Let the weight of the mix in the air be = [tex]W_{ma}[/tex]
Let the weight of the mix in water be = [tex]W_{mw}[/tex]; &
the bulk specific gravity be = [tex]G_m[/tex]
SO;
[tex]W_{mw} = W_{ma} - v \delta _{w} --- (1)[/tex]
Also;
[tex]G_m = \dfrac{W_{mw}}{v \delta_w} --- (2)[/tex]
From (2), make[tex]v \delta_w[/tex] the subject:
[tex]v \delta_w = \dfrac{W_{ma}}{G_m}[/tex]
Now, equation (1) can be rewritten as:
[tex]W_{mw} = W_{ma} - \dfrac{W_{ma}}{G_m}[/tex]
[tex]G_m = \dfrac{W_{ma}}{W_{ma} - W_{mw}}[/tex]
Replacing the values;
[tex]G_m = \dfrac{1173.5}{1173.5 -652.5}[/tex]
[tex]G_m = \dfrac{1173.5}{521}[/tex]
[tex]\mathbf{G_m = 2.25}[/tex]
A primary runway is being designed for a new airport to serve airport approach category B. As part of this work it is required to design two consecutive vertical curves (a crest vertical curve followed by a sag vertical curve) to be located midway along the length of the runway. The design should satisfy all the grade and minimum length requirements. If conditions are such that the crest vertical curve connects grades of +0.5% and + 1.5%, determine all the properties of both curves that will be necessary to set out the curves. The elevation and station of the point of intersection of the two tangents of the crest vertical curve are 556.50 ft and 595 + 45.00, respectively, and the distance between the points of intersections (PVIs) of the vertical curves is 975 ft.
To design two consecutive vertical curves (a crest vertical curve followed by a sag vertical curve) located midway along the length of the runway satisfying all the grade and minimum length requirements, the properties of both curves that will be necessary to set out the curves are:
Length of the crest curve (Lc) = 50.63 feet.
Length of the sag curve (Ls) = 2531.25 feet.
Minimum length of the sag curve (Lsm) = 190.43125 feet.
So, there are a few properties of curves that are important in a runway design. Some of the significant properties of curves are:
Curvature Radius: The Curvature radius is the radius of the circle that lies on the inside edge of the curve.
Super-elevation: The angle at which a curve is banked is called super-elevation.
Longitudinal gradient: The slope of the curve is defined by its longitudinal gradient.
Setting out the Curves: Let's try to determine all the properties of both curves that will be necessary to set out the curves. To design two consecutive vertical curves that will be located midway along the length of the runway, we need to follow some steps:
1. We need to determine the distance between the PVIs of the vertical curves, which is 975 ft.
2. Determine the station of the VPIs (Vertical Point of Intersection) of each curve.
For the crest vertical curve, the station is 595 + 45.00.
3. Find the grade at the VPI of the crest vertical curve. The grade at the VPI of the crest vertical curve is the average of the grades between the PVI of the sag curve and the PVI of the crest curve.
Therefore, the grade is: Gc = (Gs + Gp) / 2 where Gs = 0.5% and Gp = 1.5%.
Hence Gc = (0.5% + 1.5%) / 2 = 1%.
4. The vertical distance between the VPI of the crest curve and the VPI of the sag curve is defined as "y."
5. The elevation of the VPI of the crest vertical curve is given as 556.50 ft.
Hence, the elevation of the VPI of the sag curve will be 556.50 + y.
6. The station of the VPI of the sag vertical curve can be calculated by subtracting half of the distance between the PVIs (975/2) from the station of the VPI of the crest curve (595+45.00).
Hence the station of the VPI of the sag curve is 595+45.00-487.50 = 153+45.00.
7. The length of the crest curve (Lc) and sag curve (Ls) can be found using the equation:
Lc = 1.25 y / GcLs = 1.25 y / Gs8.
Finally, we can calculate the required minimum length of the sag curve (Lsm) by using the following equation:
Lsm = (Gs + Gc) Ls / 2 Gc
Solved Numericals:
Length of Crest Curve Lc = 1.25 y / Gc = 1.25 × 40.5 / 1% = 50.63 feet.
Length of Sag Curve Ls = 1.25 y / Gs = 1.25 × 40.5 / 0.5% = 2531.25 feet.
Minimum length of Sag Curve Lsm = (Gs + Gc) Ls / 2 Gc= (0.5% + 1%) × 2531.25 / (2 × 1%)= 38,086.25/200 = 190.43125 feet.
Thus the properties of both curves that will be necessary to set out the curves are as follows:
Length of the crest curve (Lc) = 50.63 feet.
Length of the sag curve (Ls) = 2531.25 feet.
Minimum length of the sag curve (Lsm) = 190.43125 feet.
Learn more about vertical curves:
brainly.com/question/31493952
#SPJ11