Answer:
C. 2.5 g/ml
Explanation:
Divide mass by volume
A wheel spins with constant angular acceleration on an axis through its center, the ratio of
the tangential speed of a point on the rim to the tangential speed of a point halfway between
the center and the rim is:
A. 1
B. 2
C.1/2
D. 4
The ratio of the tangential speed of a point on the rim to the tangential speed of a point halfway between the center and the rim is 2.
The correct option is B.
Briefing:The wheel's angular velocity The rate at which the angular displacement changes over time is known as the wheel's angular velocity. Because the angular velocity is constant, a point just on rim will have constant tangential velocity.
What does angular velocity?The angular velocity of a body refers to the pace at which it revolves or circumambulates an axle. Sometimes, the Greek letter omega symbolizes angular velocity. Due to the fact that it is expressed as an angle every unit of time, the angular velocity in the SI was measured in radians per second.
To know more about Angular velocity visit:
https://brainly.com/question/12446100
#SPJ9
A sample of a gas is in a container. The temperature of the gas is decreased. Based on the relationship between temperature and pressure, what must have happened to the pressure?
If the temperature of the gas is decreased then the pressure will also decrease.
The molecules of a gas receive more energy when heated, causing them to move more quickly. This results in increased pressure and more impacts on the container's walls. On the other hand, cooling the molecules will cause them to slow down and reduce pressure.
This is more explained by Gay Lussac's Law which states that the pressure of a given amount of gas held at constant volume is directly proportional to the Kelvin temperature.
P1/T1 = P2/T2
Thus, with decrease in temperature the pressure will decrease as the move of molecules will be slow now.
To know more about Gay Lussac's Law visit the link:
https://brainly.com/question/2683502?referrer=searchResults
#SPJ9
What is the total translational kinetic energy of 1.6 mol of N₂ molecules at 27°C?
The total translational kinetic energy of 1.6 mol of N₂ molecules at 27°C is calculated as 9673 J as pern the Kinetic energy formula with Boltzmann Constant.
How is translational kinetic energy calculated?Remember that the mass of the item multiplied by the square of its linear velocity (around its center of mass) yields translational kinetic energy, which is then divided by two.
What is the kinetic energy of translation?The energy of motion of a body is equivalent to the work it would perform if it were brought to rest, according to general physics.
For a rigid body with constant mass, the translational kinetic energy is dependent on motion through space and is calculated as the product of the square of the speed and the product of the mass divided by half.
N2 is an adiatomic molecule
Total translational Kinetic energy of adiatomic gas
E = 5/2 NKT
1 mol = 6.022 x [tex]10^{23}[/tex]
1.6 mol = 1.6 x (6.022 x [tex]10^{23}[/tex])
= 9.635 x [tex]10^{23}[/tex]
Boltzmann constant K = 1.38 x [tex]10^{-23}[/tex] J/K
Temperature = 18° C
= (18 + 273) K
= 291 K
Putting the values,
E = 5/2 x (9.635 x [tex]10^{23}[/tex] ) x (1.38 x [tex]10^{23}[/tex]) x 291 K
= 9673 J
To know more about Kinetic Energy visit:
https://brainly.com/question/14799724
#SPJ9
hd 93083. note that planet b is in this star’s chz. now in fact this planet has a mass of at least 0.37 jupiter masses. is this planet a likely candidate to have life like that on earth? why or why not?
True now in fact this planet has a mass of at least 0.37 jupiter masses. is this planet a likely candidate to have life like that on earth
Due to its greater mass, the planet would be subject to a stronger gravitational pull. The gravitational pull depends on two things:
Weight of the body
Distance
The planet's mass is 118 times more than Earth's, therefore the life forms there would be very different from those on Earth.
The supplied response is accurate since the planet's is far greater than the earth's, and it also relies on the planet's distance from its star in the solar system and the quantity of heat that it receives. Europa would be submerged in water as a result of the ice being warm enough to melt.
Oort cloud perturbations are not considered to be extinction events.
Supernovas are extinction-level events.
Learn more about planet here:
https://brainly.com/question/14581221
#SPJ4
What was the kelly-bessemer process used for? reducing the speed for laying rail tracks mass producing train cars monopolizing the iron industry making high-quality steel
The kelly - bessemer process used for converting the iron metal to molten steel by injecting air into molten pig iron.
Molten steel (from an oxygen or electric arc furnace) is poured into a ladle that is brought to the inlet of a continuous casting machine, raised onto a turret, and poured into a tundish. This is a large vessel that ensures the continuous flow of hot metal through a submerged entry nozzle and into a water-cooled and vertical copper mould, where the solidification starts as an outer shell starts encasing a liquid core. Hydrogen is highly soluble in molten steel, including weld metal.
The partial pressure or concentration of hydrogen above the molten steel determines the equilibrium solubility. It is a really difficult process.
Learn more about Molten steel here
https://brainly.com/question/28354355
#SPJ4
i need help with this lab. i have to answer the lab questions 4-10. i will upload the graphs u need to use. someone please answer these questions. i will upload the pictures in different questions because it won’t let me upload 3…
The speed of an object is the rate of change of its position, and the object's velocity includes its speed as well as its direction of motion. The rate of change of the object's velocity gives the acceleration.
Explain Speed,Velocity and Acceleration?When an object's reference frame is chosen, its motion can be precisely characterized. The pace at which an object's position changes while it is moving is referred to as speed. The object's speed indicates how quickly or slowly it is going. But which way is the item traveling? The velocity of an object includes information about its direction of motion. The rate of change of an object's velocity, or the change in velocity per unit of time, is known as its acceleration.
To learn more about Speed,Velocity and Acceleration refer to:
https://brainly.com/question/2169703
#SPJ13
how does a coal-fired power plant use the energy in coal to produce electricity? burning coal heats wires to very high temperatures, which then generate electricity. burning coal generates light that is converted into electricity. burning coal heats water and creates steam that turns the blades of a turbine and generates electricity. burning coal heats air that spins the blades of a turbine and produces electricity.
Coal is burned to create steam, which is then used to generate electricity at coal-fired power stations. Under extreme pressure, the steam generated enters a turbine, which turns a generator to provide power. In order to restart the process, the steam is then cooled, condensed back into water, and fed back into the boiler.
For example, the Kingston Fossil Plant near Knoxville, Tennessee, uses coal to heat its boilers to around 1,000 degrees Fahrenheit in order to produce high-pressure steam as a practical illustration of this.
How is energy generated by burning coal?
Whether bituminous, subbituminous, or lignite, they are all burned in coal-fired power plants. The heat generated by coal combustion is utilized to turn water into high-pressure steam, which drives a turbine and generates electricity.
To learn more about coal visit:
https://brainly.com/question/22647554
#SPJ9
A bullet is accelerated in the muzzle of a gun from rest to 150 m/s in 0.50sec. What is the acceleration?
Answer:
Bullets are cylindrical metal projectiles shot from firearms. Their main function is to kill or otherwise incapacitate. They come in numerous varieties for use in handguns, rifles, and machine guns. There is also special ammunition capable of penetrating armor, firing underwater, or firing "silently" at subsonic speeds. However, their designs are all basically the same. A typical cartridge consists of four components: the cartridge case, primer, propellant charge and bullet. When a gun trigger is pulled, the primer is struck, igniting the propellant. This causes a rapid expansion of gas, which forces the bullet forward and ejects the casing. Contrary to popular belief, guns are not loaded with bullets, but cartridges, and they fire bullets (since bullets are a more common term and the actual objects responsible for harm, they receive the recognition).
While small in size (the most popular handgun bullet is 9 mm in diameter) bullets posses enough kinetic energy to cause serious damage. Using a kinematics formula, it is possible to determine the acceleration of a bullet when the muzzle velocity and barrel length of a gun are known.
v2 = vo2 + 2as
Where
v is the muzzle velocity
vo is the initial velocity of the bullet, which is zero
a is the acceleration
s is the barrel length
Since acceleration is the desired value, the derived formula is this:
equation
When fired from a Beretta 92S, the standard issue US Army pistol, a 9 mm Parabellum bullet has a muzzle velocity of 335 m/s. With its 127 mm barrel length, the bullet's acceleration is calculated to be 4.4 × 105 m/s2.
The acceleration of a bullet depends largely on the gun from which it is fired, along with the intent of the user. Pistol bullets generally feature a lower acceleration than rifles or machine guns. Also, individuals involved with clandestine operations may use firearms with silencers, which suppress bullet speed and require special subsonic ammunition.
Remember, guns don't kill people. Bullets do. To paraphrase Chris Rock in Bigger, Blacker and Uncut, if bullet prices were raised to $5,000 each, there would be a drastic decrease in murders [mp3].
a sonar system can use sound waves wih a frequency of 120kHz or 200kHz. A. what is the wavelength of each of these waves when they are sent through sea water?
B. What are their wavelengths in freshwater?
C. The ship operating these sonar systems is in sea water with a depth of 3km.
How long will it take an echo to return to the ship after a ‘ping’
(A) The wavelength of each of these waves when they are sent through sea water is 0.0126 m and 0.0076 m respectively.
(B) The wavelength of each of these waves when they are sent through freshwater is 0.012 m and 0.0074 m respectively.
(C) The time taken for the echo to return to the ship is 3.97 seconds.
What is the wavelength of the sound wave in sea water?
The wavelength of the sound wave in sea water depends on the speed of sound in seawater and frequency of the wave.
The speed of sound in seawater, v = 1,510 m/s
λ = v/f
when the frequency, f = 120 kHz
λ = 1510 / 120,000
λ = 0.0126 m
when the frequency, f = 200 kHz
λ = 1510 / 200,000
λ = 0.0076 m
The speed of sound in freshwater, v = 1481 m/s
when the frequency, f = 120 kHz
λ = 1481 / 120,000
λ = 0.012 m
when the frequency, f = 200 kHz
λ = 1481 / 200,000
λ = 0.0074 m
The time taken for the echo to return is calculated as follows
v = 2d/t
t = 2d/v
t = (2 x 3,000 m) / (1510 m/s)
t = 3.97 s
Learn more about wavelength here: https://brainly.com/question/10728818
#SPJ1
Did DART apply a balanced or unbalanced force to the satellite during the collision? What evidence supports your answer?
Answer:
A collision is an interaction between two objects that have made contact (usually) with each other. As in any interaction, a collision results in a force being applied to the two colliding objects. Newton's laws of motion govern such collisions
An interaction between two items that have made contact with one another is referred to as a collision. A collision exerts a force on the objects interacting, just like any other interaction. Such collisions are regulated by Newton's laws of motion.
What is collision?In physics, a collision, which is also known as an impact, is the abrupt, violent coming together and in near vicinity of two bodies, such as two pool cues, a golf club and a ball, a hammer as well as a nail, two railroad cars when linked, or a falling item and a floor.
The force and the amount of time the objects are in touch, in addition to the materials the two objects are made of, have an impact on the outcome of the impact. Generally,is common knowledge that a hardened steel ball bounced on a steel plate would rebound almost to the original position from where it was dropped, while a ball made of putty and lead will not.
To know more about collision:
https://brainly.com/question/13138178
#SPJ2
what is the total work wfric done on the block by the force of friction as the block moves a distance l up the incline? express the work done by friction in terms of any or all of the variables μ , m , g , θ , l , and f1 .
The work done by friction W = (F1 - mg sin θ) L, W = -μ mg cos θ L.
Use Newton's Second Law to find the force of friction. In these tasks, the X-axis will be parallel to the plane and the Y-axis will be perpendicular to the plane:
Y-Axis
N - =[tex]w_{y}[/tex]
N = W_{y}
X axis
F1 - fr - Wₓ = 0
fr = F1 - Wₓ
Let's use trigonometry to find the components of the weight
sin θ = Wₓ / W
cos θ = W_{y} / W
Wₓ = W sin θ
W_{y} = W cos θ
We substitute
fr = F1 - W sin θ
Work is defined by
W = F .dx
W = F dx cos θ
Since the friction force is in the negative direction parallel to the plane and the displacement along the plane is positive, the angle is 180° and cos θ = -1
W = -fr x
W = (F1 - mg sin θ) L
Another way to calculate is
fr = μ N
fr = μ W cos θ
the work is
W = -μ mg cos θ L.
Zero work can occur in any of the following situations When a single force is applied but no displacement. There are gaps but the power of the individual is not showing. A single force is applied in a direction perpendicular to the direction of displacement.
Learn more about The friction force here:-https://brainly.com/question/23161460
#SPJ1
the combined force that you and your friends exert has magnitude 8.00×102n , and starting from rest the car reaches a speed of 1.40 m/s after you have pushed it 5.00 m . find the magnitude of the constant friction force that acts on the car.
The magnitude of the constant frictional force that acts on the car is 574.6
What is frictional force?The frictional force is the force that acts to oppose the relative motion of an object over another.
Friction is a contact force that acts at the surface of contact between two bodies.
The frictional force acting on an object depends on the following:
the coefficient of friction between the surfaces- the coefficient of friction between the two surfaces is a constant ad depends on the nature of the surfaces.the weight of the object moving over another. The greater the weight of the object moving over another surface, the greater the frictional force, and vice versa.The total force exerted by the friends = 800 N
Force on the car as it moves will be = mass * acceleration
acceleration, a = v² - u² / 2 * s
a = 1.40² - 0² / 2 * 5
a = 0.196 m/s²
force = 1.15×10³ kg * 0.196 m/s²
force = 225.4 N
Frictional force = 800 - 225.4
Frictional force = 574.6 N
Learn more about frictional force at: https://brainly.com/question/4618599
#SPJ1
Complete question:
A car of mass 1.15×10^3kg is stalled on a horizontal road. You and your friends give the car a constant, forward, horizontal push. There is friction between the car and the road.
the combined force that you and your friends exert has magnitude 8.00×102n , and starting from rest the car reaches a speed of 1.40 m/s after you have pushed it 5.00 m . find the magnitude of the constant friction force that acts on the car.
calculate the percent efficiency of a motor that lifts a 50 n weight, 5 meters in 10 seconds. the motor is run by a 9v battery with 3 amperes of current.
The efficiency of the motor is 92.6%
The input energy comes from the motor.
W_in = P . t
Where:
P = V. i
= 9 volt. 3 A = 27 Watt
Hence,
W = 27 watt . 10 seconds = 270 Joules.
The output work is the potential energy.
W_out = F . s
= 50 . 5 = 250 Joule.
The efficiency is calculated as:
Efficiency = W_out / W_in x 100%
= 250/270 x 100% = 92.6%
Learn more about work and energy here:
https://brainly.com/question/13387946
#SPJ4
help me find intersect and slope
Answer:
58.01
Explanation:
because this is he answer to the question 019.10
Consider a 0. 5-kg meter stick with a 1. 0 kg mass attached at the 50 cm mark and a 3. 0 kg mass at the very end. Where on the meter stick is the center of mass located?.
The center of mass of the three mass system is at 83cm.
What is center of mass?The center of mass of an object or a collection of objects is known. It represents the system's average location by weighing the mass of each component. For straightforward rigid structures with uniform densities, the center of mass is located at the centroid.
What is the calculation of the above problem?Given the mass of the meter stick is:
M = 0.5kg.
Since the meter stick is uniform, the center of mass of the meter stick is at 50cm or 0.5m.
Let the distance of the meter stick's center of mass from 0cm be x1. Then x1 = 0.5m.
Now a mass m2 = 1kg is attached at 50cm mark.
So the distance of m2 from 0cm is x2 = 50cm = 0.5m.
Similarly a mass m3 = 3kg is attached at the every end or 100cm mark. So the distance of m3 from 0cm is x3 = 100cm = 1m.
Now the position of the three mass system from 0cm is given by,
So the center of mass of the three mass system is at 83cm.
To know more about Center of mass visit:
https://brainly.com/question/8662931
#SPJ9
You push a book across a table. The book moves at a constant speed, but you do not move. Identiffy all the forces on you. Then identify all of the forces on the book
The forces acting on me are static frictional force and reaction force of the book. The forces acting on the book moving with a constant speed are Applied force and Kinetic frictional force.
Forces acting on me are
Static frictional forceReaction force of the bookThe book at rest, will have a static frictional force. So when I push the book, these forces will act on me. According to Newton's third law of motion, when I apply a certain amount of force on the book, the book will exert the equal amount of force on me.
Forces acting on the book are
Applied forceKinetic frictional forceThe book when moving at constant velocity will have zero net force, because according to Newton's second law of motion, force is directly proportional to acceleration. If the velocity is constant, acceleration will be zero and net force will also be zero. Since the book is moving on a table, a kinetic frictional force will act on the book to resist the movement of the book.
Therefore,
The forces acting on me are Static frictional force and Reaction force of the book.The forces acting on the book are Applied force and Kinetic frictional forceTo know more about Newton's second law of motion
https://brainly.com/question/13447525
#SPJ1
What would be the acceleration if the force in question 1 were doubled?
Based on properties of elements in the periodic table, which element is the best conductor of thermal energy?
A. argon(Ar)
B. germanium (Ge)
C. polonium(Po)
D. vanadium(V)
Answer:A. argon(Ar)
Argon is commonly considered to be a chemical by most people
Drag each label to the correct location on the figure. Not all labels will be used.
Match the function to the correct part of the neuron.
passes electrical signals
to another neuron
contains the nucleus
and cell organelles
receives signals from
other neurons
conveys electric signals
across a long distance
protects and
insulates the axon
The function should be matched to the correct part of the neuron as follows:
Axon: passes electrical signals to another neuron.Cell body: contains the nucleus and the cell organelles.Dendrites: receives signals from other neurons.Action potential: conveys electrical signals across a long distance.Myelin: protects and insulates the axon.What is a neuron?A neuron can be defined as a nerve cell that's saddled with the responsibility of transmitting electrical signal (impulses) down an axon across a cellular membrane of the body of a living organism through an action potential.
In Science, the neuron comprises different parts and these include the following:
DendritesCell bodyMyelinAction potentialAxonIn conclusion, we can reasonably infer and logically deduce that a neuron transmits electrical signal (impulses) down an axon (a long, tail-like structure) across a cellular membrane of the body of a living organism to another neuron, usually through a process referred to as an action potential.
Read more on neurons here: brainly.com/question/13076783
#SPJ1
The international Agreed system of Units (SI) for physical measurement, are! (A) lb, fl, s (b) g,m, s (c) kg, m,s (d) cm,g,s ( e ) kg,cm,s
Answer:
Option (c) - Kg, m, s
Explanation:
The internationally agreed system of units for physical quantities is based on the fact that kg(kilogram) is the unit of mass, m(meter) is the unit of length and (second) is the unit of Time.
A person on a cruise ship is doing laps on the promenade deck. On one portion of the track the person is moving north with a speed of 3.9 ms relative to the ship. The ship moves east with a speed of 12 ms relative to the water.
The resultant speed of the person on the cruise ship is 12.62 m/s.
What is resultant speed?The resultant speed of an object is the single speed which can effectively represent two or more speed of the object.
The magnitude of the resultant speed of the person on a cruise ship is calculated as follows;
Vr² = Va² + Vb²
where;
Vr is the resultant speed of the personVa is the speed of the person to the northVb is the speed of the person to the eastSubstitute the value of the north speed and east speed to determine the resultant speed of the person on the ship.
Vr = √Va² + Vb²
Vr = √[(3.9 m/s)² + (12 m/s)² ]
Vr = 12.62 m/s
Thus, for a person on a cruise ship is doing laps on the promenade deck at a speed of 3.9 m/s to the north and the speed of the ship 12 m/s to the east, the resultant speed is 12.62 m/s.
Learn more about resultant speed here: https://brainly.com/question/25239010
#SPJ1
The complete question is below:
Find the resultant speed of the person
what is the coefficient of static friction between m1 and m2 (call this s1) and between m2 and the wall (call this s2) if the minimum force fmin required to keep the blocks from breaking loose and sliding under the influence of gravity is fmin
The static coefficient of friction between m1 and m2 and m2 and the wall (designated as s1 and s2, respectively) if the minimum force F minimum necessary to prevent the blocks from separating and sliding under the action of gravity is F minimum.
What is static friction coefficient?
The ratio of limiting friction to the usual reaction between the surfaces is known as the coefficient of static friction.
This equation yields the minimum coefficient of static friction:
When the radius of curvature R = 190 m and the vehicle's speed V is 72 km/h (20 m/s), the smallest value of the coefficient of static friction Typically, it is represented by the Greek letter mu ().
In terms of math, is equal to F/N, where F stands for frictional force and N for normal force. The coefficient of friction has no dimensions because both F and N are measured in units of force (such as newtons or pounds). friction equals 0.21.
To learn more about coefficient of stastic friction refer to:
https://brainly.com/question/25050131
#SPJ 9
a uniform cube of mass m and edge a moves on a horizontal surface along the positive x-axis, with initial velocity v0: (a) during motion, n>mg (b) during motion, normal reaction acts on the centre of mass (c) during motion, the normal reaction shifts towards positive x-axis from the centre of mass (d) during motion, normal reaction shifts in the direction of the forces of friction
Option C about friction is correct statement with initial velocity v0.
What is friction?
friction is a force that opposes motion between any surfaces that are touching. Friction can work for us yet against of us .
It is the action of one surface or object rubbing against another .
Solution -
According to the given question in this case force of friction has a tendency to rotate the cube in anticlock wise direction.
So normal reaction will shift in forword direction to balance the force due to torque of friction.
Thus,
During motion the normal reaction shift towards posetive x- axis from the centre of mass is correct.
To know more about friction click
https://brainly.com/question/24338873
#SPJ9
When a football player catches a football. Time interval or a time instant? (Please give me the right answer)
An elephant ran 300 meters in 20 seconds, what was his speed?
Answer: 40 km/hr ( c )
Explanation:
Distance =20 km
Time =30 min=
60
30
hr=
2
1
hr
∴ Speed =
time
Distance
=
(
2
1
hr)
20 km
⇒ Speed =40 km/hr
Option (C) is correct.
What electric field e′ would have been required to create a current of 30. 0 amperes in a copper gauge 10 wire with diameter d equal to 0. 259 centimeters?.
The required electric field is 9.58 × 10⁻² N/C
We know that the electric field, E is a product of resistivity and current density
∴ E=jρ ......(i)
Where ρ⇒ Resistivity
j ⇒ Current density
j = I/A
Now, as per the question,
Resistivity of copper, ρ = 1.68 × 10⁻⁸ Ωm
Current, I = 30 ampere
Diameter = 0.259 cm = 0.00259 m
So, Radius, r = Diameter/2
= 1.295 × 10 ⁻⁴m
Now, Cross-sectional area, A = πr²
= 3.14 × (0.001295)²
= 5.26 × 10⁻⁶ m²
Putting the values in equation (i), we get:
[tex]E = 1.68 \times 10^{-8} \times\frac{30}{5.26 \times 10^{-6} }[/tex]
[tex]E= 9.58 \times 10^{-2} N/C[/tex]
Therefore, the required electric field is 9.58 × 10⁻² N/C
Read more about Electric field:
https://brainly.com/question/14972426
#SPJ9
Marco and his sister are rummaging through a large box of books. Their younger brother also wants to see what’s inside the box. Marco pulls the box away from his brother, applying a force of 38 N to the left. His sister helps him by applying an additional force of 36 N to the left. Their brother applies a force of 35 N to pull the box in the opposite direction. The box weighs 22 kg. Determine the acceleration of the box.
By applying net force formula, the acceleration of the box is 1.8 m/s²
What is Acceleration ?Acceleration is the velocity change per time taken. It is a vector quantity and it is measured in m/s²
Given that Marco pulls the box away from his brother, applying a force of 38 N to the left. His sister helps him by applying an additional force of 36 N to the left. Their brother applies a force of 35 N to pull the box in the opposite direction. The box weighs 22 kg.
F = ma
Where
F = Net force = sum of the left forces - sum of the right forces m = 22 Kga = ?To determine the acceleration of the box, substitute all the parameters into the formula
(38 + 36) - 35 = 22 a
74 - 35 = 22a
39 = 22a
a = 39/22
a = 1.77 m/s²
Therefore, the acceleration of the box is 1.8 m/s² approximately.
Learn more about Acceleration here: https://brainly.com/question/605631
#SPJ1
What is the point on an object where the force of gravity is considered to act?
The Centre of gravity is the point on an object where the force of gravity is considered to act.
Every object that exists on the earth has weight and because of that weight, certain gravity acts on it. When we calculate the total weight of the object, mainly center is taken as the point where the whole weight of the object is accumulated.
for instance, in the seesaw, the middle portion of it acts as a center of gravity which balances out both sides.
It plays a very important role in calculating big and complex problems of gravitation. It simplifies calculations to treat the mass of an object as if it is concentrated at one point only. It is an imaginary point that stable the object.
To learn more about centre of gravity, follow the below link:
https://brainly.com/question/874205
If Rico pulls on a 30 kg box of supplies with a force of 200 N towards the nearest firefight and Ace pulls on the box with a force of -56 N in the opposite direction, what is the net force (in Newtons) on the box of supplies?
The net force (in Newton) on the box of supplies, given that Rico pulled it with a force of 200 N is 256 N
How do I determine the net force?From the question given above, the following data were obtained:
Mass of box = 30 KgForce of pull = 200 NOpposite force = -56 NNet force =?The net force on the box of supplies can be obtained as illustrated below:
Net force = force of pull - opposite force
Net force = 200 - (-56)
Net force = 200 + 56
Net force = 256 N
Thus, the net force on box is 256 N
Learn more about net force:
https://brainly.com/question/18109210
#SPJ1
a freight train is traveling due west at 10 miles per hour and begins to slowly pick up speed. of the train reaches a speed of 70 mph in 2 hours, what is the average acceleration of the train.
Answer:
Since 60 mph = 88 ft/sec
10 mph = 14.7 ft/sec
70 mph = 7/6 * 88 ft/sec = 103.7 ft/sec
a = (v2 - v1) / t = (103.7 - 14.7) ft/sec / 7200 sec = .0124 ft/sec^2