True or False? although inductive current lags inductive voltage by 90°, both waves have the same frequency.

A non metallic cable shall be secure at intervals not exceeding 4.5 feet and within 12 inches of the box to protect the cable and ensure proper support for electrical connections, as specified in section 334.30 of the National Electrical Code.

The metals loses electrons forming cations while on the other hand, the non-metals gains the electrons forming anions.

Covalent bonding is a type of bonding linking two non-metallic atoms which are distinguished by the sharing of pairs of electrons joining atoms and other covalent bonds. An ionic bond is the force of appeal that holds together positive and negative ions. It forms when atoms of a metallic element loses electrons to atoms of a nonmetallic element. Ionic bonds form only allying metals and nonmetals. When two nonmetals bond, they share pairs of electrons in a covalent bond and both gets stability.

So w can conclude that A covalent bond is formed between two non-metals. The sharing of electron pairs takes place between their atoms and a covalent bond is formed.

Learn more about non metallic here

https://brainly.com/question/29400906

#SPJ11

Receptacles installed outdoors in a wet location shall have an enclosure that is weatherproof, whether or not the attachment plug cap is installed. This requirement is stated in the National Electrical Code (NEC) section 406.9.

According to section 406.9 of the National Electrical Code (NEC), receptacles installed outdoors in a wet location shall have an enclosure that is weatherproof, whether or not the attachment plug cap is installed. This means that the enclosure must be designed to prevent water from entering the receptacle, even when the plug is not connected to it. This is important because water can cause electrical shocks and create hazards that could lead to injury or damage to electrical equipment. To comply with this code requirement, outdoor receptacles are typically designed with covers that provide a tight seal around the receptacle and the plug when it is inserted. Additionally, the enclosure must be able to withstand exposure to weather and outdoor conditions, such as rain, snow, and extreme temperatures.

Learn more about temperatures here-

https://brainly.com/question/11464844

#SPJ11

The statement you provided is: "Connections from cellular concrete floor raceway headers to cabinets shall be made by means of listed metal raceways or PVC raceways." Based on this information, the statement is True.

Cement, water, coarse aggregates, fine aggregates (i.e. sand), and air are the five essential ingredients that make up a concrete mix, which can be combined in different ratios.

To give the mixture the attributes you want, you can add cellular concrete more ingredients such pozzolanic minerals and chemical admixtures.

Concrete is created with the aid of cement, sand, gravel, and water.

These ingredients should be combined in the following ratios: 1:2:3:0.5 to achieve maximum power. Those proportions are one part cement, two parts sand, three parts gravel, and one and a half parts water.

Learn more about  cellular concrete here

https://brainly.com/question/31545285

#SPJ11

An enclosure that contains a device(s) shall have a weight supported by a single conduit that does not exceed 50 lbs according to NEC code 314.23(f)(e).

According to the National Electrical Code (NEC) section 314.23(f)(e), an enclosure that contains a device(s) shall have a weight supported by a single conduit that does not exceed 50 pounds. This means that the weight of the enclosure and any devices contained within it should not exceed 50 pounds if they are supported by a single conduit. It is important to note that this requirement applies to the weight supported by a single conduit, and not the overall weight of the enclosure and devices. If the weight exceeds 50 pounds, additional supports or mounting brackets may be required to ensure the safety and stability of the installation.

Learn more about pounds here-

https://brainly.com/question/29181271

#SPJ11

The answer to the aforementioned question is True.

True, it is permissible to run unbroken lengths of surface metal raceways through dry walls, partitions, or floors.

This allows for a safe and efficient installation of electrical wiring in various spaces, while maintaining structural integrity and complying with electrical codes.

Learn more about codes at : brainly.com/question/497311

#SPJ11

Alternators are devices used to convert mechanical energy into electrical energy. They are widely used in vehicles to recharge the battery and power the electrical systems of the vehicle. Alternators operate based on the principle of electromagnetic induction, which involves the creation of a magnetic field in the rotor to generate electrical energy.

Technician A is correct in stating that a magnetic field is created in the alternator rotor. The rotor is the rotating part of the alternator that contains a series of windings. When an electrical current flows through these windings, a magnetic field is created in the rotor. This magnetic field interacts with the stator, which is a stationary part of the alternator that contains a series of windings, to generate an electrical output.

Technician B is incorrect in stating that alternator output is increased if the speed of the alternator is decreased. The output of an alternator is directly proportional to the speed of the rotor. The faster the rotor spins, the higher the output of the alternator. Therefore, if the speed of the alternator is decreased, the output will also decrease.

In conclusion, both technicians are partially correct, but Technician A is more accurate. A magnetic field is created in the alternator rotor, and the output of the alternator is directly proportional to the speed of the rotor.

Learn more about magnetic field here:

https://brainly.com/question/14848188

#SPJ11

For safety reasons, it is important to ensure that nonmetallic underground conduit with conductors is trimmed away from the conductors or cables using an approved method that will not damage the conductor or cable insulation or jacket. This is especially important in situations where electrical currents are present, as damage to the insulation or jacket could result in electrical shocks, fires, or other hazards.

For such more question on nonmetallic

https://brainly.com/question/2834632

#SPJ11

The valve that has a solenoid which varies the amount of air allowed into the carburetor when the throttle valve is closed is called the idle air control valve (IAC valve).The valve you're referring to is the Idle Air Control (IAC) valve. It has a solenoid that adjusts the amount of air allowed into the carburetor when the throttle valve is closed, helping to maintain a proper idle speed for the engine.

The valve you are referring to is called an Idle Air Control (IAC) valve. The IAC valve is typically mounted on the throttle body and is controlled by the engine control module (ECM) or the powertrain control module (PCM). Its purpose is to regulate the engine idle speed by controlling the amount of air that bypasses the closed throttle plate when the accelerator pedal is released. The solenoid in the IAC valve varies the amount of air allowed into the engine to maintain a stable idle speed.

Learn more about solenoid here

https://brainly.in/question/918309

#SPJ11

True. In the s-domain, the voltage across a resistor with current i(t) flowing through it can be represented as s times the product of the resistance R and the current i(t), which is equal to sri(s). This is known as the impedance of a resistor in the s-domain.

The Laplace transform takes a continuous time signal and transforms it to the s

-domain.

The Laplace transform is a generalization of the CT Fourier Transform. Let X(s)

be the Laplace transform of x(t)

, then the Fourier transform of x

is found as X(jω)

For most engineers (and many fysicists) the Laplace transform is just a mathematical trick to easily solve a class of partial differential equations. The Laplace transforms a constant coefficient linear differential equation relating the input x(t)

with the output y(t)

into an algebraic polynomial in s

. We will look at this class of constant coefficient linear partial differential equations.

learn more about impedance here:

https://brainly.com/question/30040649

#SPJ11

Hi!

The statement is false.

The voltage across a resistor with current i(t) in the s-domain is given by V(s) = R*I(s), where R is the resistance and I(s) is the Laplace transform of the current i(t).

Learn more about resistance and current: https://brainly.com/question/24858512

#SPJ11

A source host TCP process will retransmit a segment if it does not receive an acknowledgement (ACK) from the destination host within a certain time period known as the Retransmission Timeout (RTO).

The RTO is calculated based on various factors such as network congestion, previous round-trip time, and other network conditions. Additionally, TCP can also use the Fast Retransmit algorithm, which triggers a retransmission if the source host receives multiple duplicate acknowledgements (DupACKs) from the destination host.


1. Timeout: If the sender does not receive an acknowledgment (ACK) from the receiver within a specified time, it assumes that the segment was lost or corrupted. The source host's TCP process will then retransmit the segment.

2. Duplicate ACKs: If the sender receives multiple duplicate ACKs for a segment, it assumes that the segment was lost and needs to be retransmitted. This is called fast retransmission.

3. Selective Acknowledgment (SACK): If the receiver sends a SACK, it indicates that it has received some non-contiguous segments. The source host's TCP process will retransmit the missing segments in the gap.

In summary, a source host's TCP process will retransmit a segment if it detects a timeout, receives duplicate ACKs, or receives a selective acknowledgment.

Learn more about duplicate here : brainly.com/question/15458985

#SPJ11

Memberwise assignment refers to the process of copying the individual elements (or members) of one data structure to another, while maintaining their respective order and positions. This type of assignment is often used in data structures like arrays, structs, and classes.

Here's a step-by-step explanation of memberwise assignment:

1. Identify the source and target data structures.
2. Ensure that the data structures have the same type and size.
3. Iterate through each element in the source data structure.
4. For each element, assign the value from the source to the corresponding position in the target data structure.
5. Continue until all elements have been copied.

In short , memberwise assignment is a way to transfer the contents of one data structure to another, ensuring that all individual elements are copied and their order is preserved.

Learn more about data structure here :

brainly.com/question/13147796

#SPJ11

One example in which the order of doing things can make a big difference is baking a cake.

The order of adding ingredients and mixing them can impact the texture and flavor of the final product.

Let's consider an example that highlights the importance of the order in which you do things, using terms like sequence, efficiency, time management, and task prioritization.
Suppose you have a set of tasks to complete:

cooking dinner, doing laundry, and studying for an exam.

The order in which you perform these tasks can make a significant difference in efficiency and time management.
Prioritize tasks:

First, you need to identify the most time-sensitive and important tasks. Studying for the exam should take precedence because it requires the most focus and has long-term consequences.
Sequence tasks:

Next, arrange the tasks in a logical order based on their priority and time requirements.

A suitable sequence would be doing laundry, cooking dinner, and then studying for the exam.
Efficiency:

By choosing the right sequence, you can maximize efficiency.

For instance, doing laundry first allows you to complete a passive task while focusing on other activities, such as cooking dinner.

This way, you are utilizing your time effectively.
Time management:

Properly sequencing tasks helps with time management, as it prevents wasting time on less important tasks and ensures that higher-priority tasks are addressed first.

In our example, studying for the exam has the most significant impact on your overall success, so it's essential to dedicate enough time to it.
By prioritizing tasks and performing them in a logical order, you can increase efficiency and improve time management, leading to better outcomes in various aspects of life.

The order in which you do things can make a big difference, and our example demonstrates the importance of task prioritization and sequencing in everyday situations.

For similar questions on Difference

https://brainly.com/question/13260444

#SPJ11

The formula for figuring a BASE asphalt spread rate is (asphalt weight)/(area covered) = asphalt spread rate.

The base asphalt spread rate formula is used to determine how much asphalt is required to completely cover an area. The asphalt spread rate is calculated by dividing the weight of the asphalt by the area it will cover. Weighing the asphalt on a scale will reveal how much it weighs. By taking measurements of the length and breadth of the area to be paved and multiplying them, the total area in square feet or square metres may be calculated. Common units of measurement for the resulting spread rate are pounds per square yard or kilogrammes per square metre. This formula is important in ensuring that the right amount of asphalt is used to achieve the desired thickness and quality of the pavement.

learn more about asphalt spread rate here:

https://brainly.com/question/31556224

#SPJ11

In straight pulls, the length of the box shall not be less than eight times the largest raceway. This requirement is stated in the National Electrical Code (NEC) Section 314.28(1).

Unless otherwise permitted in accordance with 300.3, all conductors of the same circuit, including the grounded conductor when used, and all equipment grounding conductors and bonding conductors, must be housed within the same raceway, cable tray, cable bus assembly, trench, or cord.

The circuit conductor sections providing an outlet that is supplied by an underfloor raceway must likewise be removed from the racetrack when the outlet is removed. All points of the system must have continuous raceway conductors [300.13]. As a result, raceway splices are not allowed unless specifically approved by 376.56, 378.56, 384.56, 386.56, 388.56 or 390.80. In its entirety, the query is:

Sections of the circuit conductors providing an outlet that is supplied through an underfloor raceway must be removed when the outlet is removed.

Learn more about raceway here

https://brainly.com/question/29934734

#SPJ11

The Square class has a side attribute and perimeter and area methods, an instance of the Square class is created and its perimeter and area are called using the object's methods.

The paragraph describes the specification for a Python class called "Square" which represents a square shape.

It has an attribute named "side" which represents the length of each side. The class has two methods: "perimeter" and "area" which return the perimeter and area of the square, respectively.

An instance of the Square class is created with a parameter specifying the length of the square's side.

The perimeter and area methods are then called on the created object.

Learn more about Square class

brainly.com/question/29796944

#SPJ11

According to the National Electrical Code (NEC) 344-10(B)(1), rigid metal conduit is allowed to be installed in concrete, in direct contact with the earth, or in areas subject to severe corrosive influences. When installed in concrete or in direct contact with the earth, it is protected from physical damage and provides a reliable grounding path. However, in areas with corrosive influences, the rigid metal conduit may be subject to degradation and require additional protection.

In summary, rigid metal conduit can be installed in concrete or in direct contact with the earth, and in areas subject to severe corrosive influences, it must be protected with appropriate measures that are judged suitable for the condition.

Learn more about concrete here: brainly.com/question/28903866

#SPJ11

Shale is the primary source rock for the vast majority of the world's oil and natural gas reserves.

A typical source rock of oil, which started out as mud in which dead organic matter settled, is shale. Shale is a sedimentary rock that is formed from the accumulation of clay and other fine-grained sedimentary particles. Over time, the accumulation of dead organic matter, such as plankton and algae, is buried by the sedimentary layers and undergoes a process of heat and pressure called diagenesis, which eventually transforms the organic matter into hydrocarbons such as oil and natural gas.

Learn more about rock here:

https://brainly.com/question/17137899

#SPJ11

The address on a PC that does not change, even if the PC is moved to a different network, is the MAC (Media Access Control) address. The MAC address is a unique identifier assigned to network interfaces for  on a physical network.

The Media Access Control (MAC) address of a network interface card (NIC) on a PC does not change, even if the PC is moved to a different network. The MAC address is a unique identifier assigned to the NIC by the manufacturer and is used to identify devices on a local network. It is different from an IP address, which can change if the PC is moved to a different network with a different subnet or if the network configuration is changed.

Learn more about network here

https://brainly.in/question/13044019

#SPJ11

answer: c. Generic methods.
Generic methods enable programmers to specify, with a single method declaration, a set of related methods.

Generic methods enable programmers to specify, with a single method declaration, a set of related methods. This is because generic methods allow for type parameters to be used in the method declaration, which can then be used to define the types of the arguments and return values for the related methods. This makes the code more flexible and reusable, as the same method declaration can be used with different types of arguments and return values.Generic Method: Generic Java method takes a parameter and returns some value after performing a task. It is exactly like a normal function, however, a generic method has type parameters that are cited by actual type. This allows the generic method to be used in a more general way.

learn more about Generic methods here:
https://brainly.com/question/12995818

#SPJ11

Therefore, the required plastic section modulus for a W12 shape using grade 50 steel is approximately 5.48 in³.

To calculate the required plastic section modulus (Z), we need to know the maximum moment the beam will experience. This can be found using the formula:

Mmax = (wL²)/8

where w is the load per unit length (4 k/ft), L is the span of the beam (25 ft), and ² denotes "squared".

Substituting the given values, we get:

Mmax = (4 k/ft x 25 ft²)/8 = 312.5 k-ft

Now, we can use the formula for the plastic section modulus of a W12 shape, which is:

Z = 2Iy/Fy

where Iy is the moment of inertia about the y-axis and Fy is the yield strength of the steel. For grade 50 steel, Fy is 50 ksi.

The moment of inertia of a W12 shape can be found from reference tables or calculated using software.

Assuming a conservative value of Iy = 137 in⁴, we get:

Z = 2 x 137 in⁴ / 50 ksi

= 5.48 in³

To know more about plastic section modulus,

https://brainly.com/question/31476044

#SPJ11

The acknowledgment number in the response segment to the client is determined by the server, while the acknowledgment number in the client's ACK segment is determined by the client.

When a client establishes a TCP session with a server, the server sends a SYN-ACK response segment to the client. This segment contains an acknowledgment number that is determined by the server. The acknowledgment number represents the sequence number of the next byte the server is expecting to receive from the client.
Once the client receives the SYN-ACK segment, it sends an ACK segment back to the server. This ACK segment contains an acknowledgment number that is determined by the client. The acknowledgment number in the ACK segment indicates the next byte the client expects to receive from the server.
In summary, the acknowledgment number in the response segment to the client is determined by the server, while the acknowledgment number in the client's ACK segment is determined by the client.

Learn more about ACK segment here

https://brainly.com/question/15862961

#SPJ11

True. TW is a type of thermoplastic insulation that is suitable for use in both dry and wet locations. It has a maximum operating temperature of 60 degrees Celsius.

here is the list of several points to consider when choosing between thermoset and thermoplastic insulation:

Thermoset insulations have a higher tolerance to high temperatures compared to thermoplastic insulations. Thermoplastic insulations have a risk of heat deformation at inappropriately hot temperatures.

Thermoset insulations have superior flexibility, which they retain in cold temperatures. They stretch better than thermoplastic counterparts without the risk of breakage.

Thermoplastic materials are light in weight; therefore, thermoplastic insulations are a go-to when the weight matters. They can be put in very thin walls without negative consequences.

Thermoplastic insulations are easier to produce, which makes them cheaper than thermoset analogs.

Thermoplastic insulations are recyclable, while thermoset insulations cannot be recycled.

Thermoset insulations are quite hard and rigid, which can be a pro or a con depending on the particular electrical application.

learn more about thermoplastic insulation here:

https://brainly.com/question/29596428

#SPJ11

MV cable shall be permitted for use on power systems rated up to 35,000 volts in raceway, wet, and dry locations. This information can be found in section 328.10 of the National Electrical Code (NEC).

The right response is pneumatic power systems since these systems are made up of connected parts that use compressed air to operate automated machinery.

As for how this system functions, it generates, transmits, and controls power by using fluid power, such as a gaseous medium under pressure.

Since the President directs the executive arm of the federal government, the United States can be categorised according to a system and executive authority as having "A federal system with presidential power."

Learn more about power systems here

https://brainly.com/question/24500125

#SPJ11

According to section 390-4(b) of the National Electrical Code, underfloor raceways that are spaced less than 1 inch apart must be covered with concrete to a depth of at least 2 inches. This is to ensure that the raceways are properly protected and that any potential hazards are minimized.

The concrete cover provides a strong and durable barrier that can withstand heavy loads and foot traffic, as well as protect against accidental damage from tools or equipment.

It is important to note that this requirement applies only to underfloor raceways and not to other types of electrical conduit or wiring. It is also important to follow all local codes and regulations when installing or working with electrical systems, to ensure the safety of both people and property.

Learn more on Raceways here : brainly.in/question/49268201

#SPJ11

The target asphalt spread rate for non FC-5 mixes is determined based on several factors, including the mix design, desired density, and available equipment.

Here are the steps to determine the target asphalt spread rate:

Determine the mix design: The mix design specifies the proportions of aggregates, asphalt, and other materials needed to produce the desired mix properties. The mix design should be optimized to achieve the desired level of performance and durability.

Determine the desired density: The desired density is typically specified in terms of a percentage of the maximum theoretical density (MTD) for the mix. The MTD is the density that would be achieved if all air voids were eliminated from the mix. The desired density should be selected based on the anticipated traffic volume and the level of compaction that can be achieved with the available equipment.

Determine the available equipment: The asphalt spread rate is affected by the equipment used to place the mix. The equipment should be capable of achieving the desired density without overcompacting the mix, which can cause rutting and other pavement distresses.

Calculate the target asphalt spread rate: Once the mix design, desired density, and available equipment have been determined, the target asphalt spread rate can be calculated. The target asphalt spread rate is typically specified in terms of pounds per square yard (PSY) or kilograms per square meter (KSM) of pavement surface area.

The target asphalt spread rate for non FC-5 mixes can vary depending on the specific mix design, desired density, and equipment used. It is important to carefully consider these factors and select the appropriate asphalt spread rate to achieve the desired pavement performance and durability.

Learn more about asphalt asphalt   here:

https://brainly.com/question/29589497

#SPJ11

There are several methods that can be used for strengthening metals. Some of these methods include:

1. Heat Treatment - This involves heating the metal to a specific temperature and then cooling it down quickly to change its microstructure, resulting in increased strength.

2. Cold Working - This involves deforming the metal at room temperature through processes such as rolling, forging, or extrusion, which increases its strength.

3. Alloying - This involves adding other elements to the metal to improve its properties, such as strength, hardness, and corrosion resistance.

4. Surface Hardening - This involves treating the surface of the metal to improve its wear resistance, such as through processes like carburizing, nitriding, or induction hardening.

1. Work hardening: This method involves deforming the metal through processes like bending, rolling, or hammering. The deformation causes an increase in dislocation density, making it harder for the atoms to move, thereby strengthening the metal.

2. Grain refinement: This method focuses on reducing the grain size of the metal. Smaller grains result in a larger total grain boundary area, which restricts the movement of dislocations and enhances the metal's strength. This can be achieved through techniques such as rapid cooling or the addition of certain alloying elements.

3. Solid solution strengthening: This method involves dissolving a secondary element into the primary metal, forming a solid solution. The atoms of the secondary element interfere with the movement of dislocations, increasing the strength of the metal. Common examples include adding carbon to iron to create steel or adding copper to aluminum to create aluminum alloy.

4. Precipitation hardening: Also known as age hardening, this method involves forming fine particles, or precipitates, within the metal matrix. These particles impede the movement of dislocations, enhancing the strength of the metal. This is typically done by heat treating the metal at specific temperatures for a set period of time.

These four methods can help improve the mechanical properties of metals, making them more suitable for a variety of applications.

Learn more about alloying here : brainly.com/question/30432755

#SPJ11

If airspeed is increased during a level turn, the angle of attack must be increased or the angle of the bank must be decreased in order to maintain altitude.

This is because an increase in airspeed will decrease the lift generated by the wings, which in turn will cause the aircraft to lose altitude if the angle of attack or the angle of the bank is not adjusted accordingly.

By increasing the angle of attack, the wings will generate more lift and compensate for the increase in airspeed, while decreasing the angle of the bank will reduce the centrifugal force acting on the aircraft and help maintain a constant altitude.
 

To maintain altitude during a level turn when airspeed is increased, the angle of attack must be increased or the angle of bank decreased. This adjustment allows the aircraft to balance the lift and maintain the same altitude while accommodating the increase in airspeed.

Learn more about the centrifugal force here:brainly.com/question/17167298

#SPJ11

The statement given "When time delay period longer than the maximum preset time allowed for a single timer is required, the problem can be solved by programming two or more timers together." is true because when a time delay period longer than the maximum preset time allowed for a single timer is required, the problem can be solved by programming two or more timers together.

This technique is called cascading timers or timer chaining, and it involves using multiple timers that are programmed to trigger in sequence.

For example, if a timer with a maximum preset time of 10 seconds is required to trigger a device after 30 seconds, three timers can be cascaded together, each set to 10 seconds. The first timer will trigger the second timer after 10 seconds, and the second timer will trigger the third timer after another 10 seconds, for a total delay of 30 seconds.

By cascading timers, longer time delays can be achieved without the need for a single timer with an excessively long maximum preset time.

You can learn more about timer  at

https://brainly.com/question/31113155

#SPJ11

Where required for the reduction of electric noise for electronic equipment, electrical continuity of metal raceway is not required, and the metal raceway can terminate to a nonmetallic fitting or spacer on the electronic equipment.

Hi! In accordance with NEC 250-96(b), where required for the reduction of electric noise for electronic equipment, electrical continuity of metal raceway is not required, and the metal raceway can terminate to a nonmetallic fitting(s) or spacer on the electronic equipment.

According to NEC 250-96(b), where it is necessary to reduce electric noise for electronic equipment, electrical continuity of metal raceway is not required. In such cases, the metal raceway can terminate to a nonmetallic fitting or spacer on the electronic equipment. This helps to prevent the transfer of electrical noise from the raceway to the equipment, which can interfere with its proper functioning. Nonmetallic fittings or spacers are used because they do not conduct electricity and therefore do not provide a path for the noise to travel.

Learn more about electrical continuity here;

https://brainly.com/question/12791045

#SPJ11