The table shows the specific heat capacities of various substances. How much energy is required to raise the temperature of 5g of air by 10°C? Use the table below to help you.

Answer:

The largest surface area window that can be used is [tex]A=0.01\ m^2[/tex]

Explanation:

Pressure

The pressure is defined as force per unit area. The SI unit for pressure is the Pascal (Pa), defined as Newton per square meter.

If a force F acts on a surface area A, the pressure is calculated as:

[tex]\displaystyle P=\frac{F}{A}[/tex]

The pressure at a depth of 90 m is P=1 Mpa= 1,000,000 Pa and the submarine's window can only take a force of F=10 kN=10,000 N.

We need to calculate the largest surface area of the window. We can solve the equation for A:

[tex]\displaystyle A=\frac{F}{P}[/tex]

Substituting:

[tex]\displaystyle A=\frac{10,000}{1,000,000}[/tex]

[tex]A=0.01\ m^2[/tex]

The largest surface area window that can be used is [tex]\mathbf{A=0.01\ m^2}[/tex]

Answer:

Anaphase: chromosomes are pulled apart

Explanation:

Anaphase is a very rapid phase of meiosis and mitosis where sister chromatids (during mitosis or meiosis II) or homologous chromosomes (during meiosis I) separate and migrate to opposite poles of the cell. In the image, the diagram represents mitosis (thus separation of sister chromatids).

During this phase, following a specific signal, the sister chromatids separate abruptly. They are then "pulled" by the "microtubules" towards the pole to which they are attached. Chromatids migrate rapidly at a rate of about 1 μm / min. Anaphase is usually divided into two distinct phases.

Answer:

The answer is C

Explanation:

Answer:

The maximum height reached by the projectile is 33.34 m

Explanation:

Given;

initial velocity of the projectile, u = 37 m/s

angle of projection, θ = 43.7°

The maximum height reached by the projectile = ?

Apply the following kinematic equation, to determine the maximum height reached by the projectile.

Maximum height (H) is given as;

[tex]H = \frac{u^2 sin^2\theta}{2g}\\\\ H = \frac{(37)^2 (sin 43.7)^2}{2*9.8}\\\\H = 33.34 \ m[/tex]

Therefore, the maximum height reached by the projectile is 33.34 m

Answer:

I believe 0

Explanation:

this is due to the fact that the box will not move anywhere the forces are canceling themselves out.  

Answer:

The correct option is;

The object is in horizontal equilibrium but NOT in vertical equilibrium

Explanation:

The given given forces in the force diagram are expressed in vector form as follows;

Topmost force = 2·i + 3·j

The horizontal force = 3·i

The force at the lower section = -5·i - 2·j

Adding the forces together to find the resultant force gives;

[tex]F_R[/tex] = 2·i + 3·j + 3·j + (-5·i - 2·j) = 5·i + 3·j - 5·i - 2·j = 0·i + j = j

[tex]F_R[/tex] = j

Therefore, the horizontal component of the forces are balanced as they cancel out and the object is said to be in horizontal equilibrium

However, the object has a net total resultant force component in the positive vertical direction, the object is not in vertical equilibrium.

Answer:

false

Explanation:

there is difference in m/s and m.s

Answer:

1) The radius of the tire is approximately 0.28966 meters

2) The centripetal force is the force that keeps a body moving on a circular path

Explanation:

1) The linear speed of the automobile tire = 20.0 m/s

The period with which the tire turns = 0.091 s

The period = The time it takes to make a complete turn

Therefore;

The number of turns in 1 second = 1/0.091 ≈ 10.989 turns

The distance covered with 10.989 turns, assuming no friction = 10.989 × The circumference of the tire

∴ The distance covered with 10.989 turns, assuming no friction = 10.989 × 2 × π × Radius of the tire

From the speed of the car, 20.0 m/s, we have;

The distance covered in 1 second = 20.0 meters

Therefore;

10.989 × 2 × π × Radius of the tire = 20.0 meters

Radius of the tire = (20.0 meters)/(10.289 × 2 × π) ≈ 0.28966 meters

The radius of the tire ≈ 0.28966 meters

2) The centripetal force is the force required to maintain the curved motion of an object, and having a direction towards the center of the rotary motion.

The centripetal force is given by the formula, [tex]F = \dfrac{m \cdot v^2}{r}[/tex]

Where;

F = The centripetal force

m = The mass of the object

v = The linear velocity of the object

r = The radius of the rotational motion.

Answer:

Its C

Explanation:

I did it on usatestprep

Answer:

V=  1,160 m

Explanation:

formula:

            V=  V*  T

remplazamos:

V= 116m /s * 10s

V=  1,160 m

Answer:

V=  1,160 m

Explanation:

Answer:

Speed of lighter ball is 4 m/s.

Explanation:

Applying the principle of conservation of linear momentum,

momentum before collision = momentum after collision.

[tex]m_{1}[/tex][tex]u_{1}[/tex] + [tex]m_{2}[/tex] [tex]u_{2}[/tex] = [tex]m_{1}[/tex][tex]v_{1}[/tex] - [tex]m_{2}[/tex][tex]v_{2}[/tex]

[tex]m_{1}[/tex] = 3 kg, [tex]u_{1}[/tex] = 8 m/s, [tex]m_{2}[/tex] = 2 kg, [tex]u_{2}[/tex] = 0 m/s ( since it is at rest), [tex]v_{1}[/tex] = 2 m/s, [tex]v_{2}[/tex] = ?

(3 x 8) + (2 x 0) = (8 x 2) - (2 x [tex]v_{2}[/tex])

24 + 0 = 16 - 2[tex]v_{2}[/tex]

2[tex]v_{2}[/tex] = 16 - 24

2[tex]v_{2}[/tex] = -8

[tex]v_{2}[/tex] = [tex]\frac{-8}{2}[/tex]

   = -4 m/s

This implies that the light ball moves at the speed of 4 m/s in the opposite direction of the heavier ball after collision.

Answer:

V = 6.56 m/s

Explanation:

in order to find the speed of the diver before she enters we need to find the vertical component of its final velocity by using 3rd equation of motion:

2gh = Vy² - V₀y²

where,

g = 9.8 m/s²

h = height = 2 m

Vy = Vertical Component of Final Velocity = ?

V₀y = Vertical Component of Initial Velocity = 0 m/s

Therefore,

2(9.8 m/s²)(2 m) = Vy² - (0 m/s)²

Vy = √39.2 m²/s²

Vy = 6.26 m/s

Assuming negligible air friction, the x-component of the final velocity will be the same as the initial velocity:

Vₓ = V₀ₓ = 1.95 m/s

Hence, the final velocity will be:

V = √(Vₓ² + Vy²)

V = √[(1.95 m/s)² + (6.26 m/s)²]

V = 6.56 m/s

Answer:process of formation

Explanation:

Answer:

ans is a .attention

plsssssssssssss mark meeee brainlist

Explanation:

Given :

The average acceleration of a tennis ball that has an initial velocity of 6.0 m/s.

and a final velocity of 7.3 m/s.

It is in contact with a tennis racket for 0.094 s

To Find :

The average acceleration of the tennis ball.

Solution :

We know, average acceleration is given by :

[tex]a_{avg}=\dfrac{Final \ velocity-Initial\ velocity}{Time\ Taken}\\\\a_{avg}=\dfrac{7.3-6.0}{0.094}\ m/s^2\\\\a_{avg}=13.83\ m/s^2[/tex]

Therefore, average velocity is given by 13.83 m/s².

Hence, this is the required solution.

Answer:

Explanation:

The distance covered by an object given it's velocity and time taken can be found by using the formula

distance = velocity × time

From the question we have

distance = 2 × 6

We have the final answer as

Hope this helps you

Answer:

Seconds...

Explanation:

Answer:

C. 212,000 years

Explanation:

believe me it's correct.....and you're welcome :)

Answer

they transfer energy

Answer:

here you go

Explanation:

so it might seem that a body on the surface of Jupiter would weigh 300 times as much as on Earth. ... But the radius of Jupiter is about 10 times that of Earth, weakening gravity by a factor of 100, resulting in 3 times its Earth weight.

Answer:

2 m/s

Explanation:

Answer:

Friction is the force between an object in motion and the surface on which it moves. Friction is the external force that acts on objects and causes them to slow down when no other external force acts upon them. Inertia is the tendency of a body in motion to remain in motion.

Answer:

Explanation:

Friction is the drive between an object in motion and the surface on which it moves. Friction is the outside constrain that acts on objects and causes them to moderate down when no other outside drive acts upon them.

Explanation:

elastic potential energy, chemical potential energy, and gravitational potential energy are all forms of mechanical energy.

Mechanical energy includes elastic potential energy, chemical potential energy, and gravitational potential energy.

To learn more about mechanical energy, refer

https://brainly.com/question/19130644

#SPJ2

Answer:

Buoyant force is directly proportional to the density of the fluid in which an object is immersed. Buoyancy is the tendency to rise or float in a fluid. The upward force exerted on objects submerged in fluids is called the buoyant force. where ρ is the density, V is the volume, and m is the mass of the displaced fluid.

Explanation:

Answer:

well It means the plant cells inside of a organism

Answer:

No, because pressure is determined by force and the area over which that force acts.

Explanation:

Answer:

12.0V

12.0V

Explanation:

.

.

.

.

.

.

.

.

.

.

.

Answer:

2.00 A

Explanation:

Answer:es la F

Explanation:

Momentum = m • v

Original momentum = m • 10 m/s north

Final momentum = m • 15 m/s north

Change = m • (15 - 10) m/s north

Change = m • +5 m/s north

Change = +60 kg-m/s north

The south pole of one bar magnet brings near the south pole of another bar magnet, they repel each other. Therefore, option (D) is correct.

A magnet can be defined as an object which is capable of producing a magnetic field and attracting unlike poles and repelling like poles. When a magnet dropped in iron filings, the iron filings cling to the end of the magnet as the attraction is maximum at the ends of the magnet.

Magnetic poles always exist in pairs whenever a magnet is suspended freely in the air, and always points in the north-south direction. The pole pointing towards the geographic north is called the North Pole and the pole pointing towards the geographic south is called the South Pole.

Similar poles of a magnet repel while unlike poles attract each other. The magnetic force between the two magnets is higher when the distance between these magnets is lesser. There are three types of magnets which are Permanent magnets, Temporary magnets, and electromagnets.

Learn more about magnets, here:

https://brainly.com/question/3617233

#SPJ5