Answer:
c
Explanation:
because abd are not the ansersers
(372-13) When an outlet is discontinued, abandoned or removed from a cellular concrete floor raceway, the sections of circuit conductors supplying the outlet shall be removed from the raceway.(True/False)
The answer is True. When an outlet is discontinued, abandoned or removed from a cellular concrete floor raceway, the sections of circuit conductors supplying the outlet shall be removed from the raceway. Based on the information provided.
Always choose conductors for a circuit conductors that are not smaller than the "minimum ampacity" of the apparatus.
By doing this, the conductor is guaranteed to be able to properly withstand the current flowing through it without overheating or harming the circuit or other machinery.
Based on the anticipated load and installation circumstances, the National Electrical Code (NEC) provides ampacity tables and formulas to assist electricians and designers in choosing the proper conductor size. It is crucial to remember that choosing a conductor that is too tiny for the load it will carry can lead to overheating, equipment damage, and even fire hazards, while choosing a conductor that is too large will result in higher material and installation expenses.
Learn more about circuit conductors here
https://brainly.com/question/31566492
#SPJ11
In Class I - Division 2 at motor fuel dispensing facilities or commercial garages the distance shall have least _______ feet of ant edge, extending in any direction.
514.3 (B)(2)
The National Electrical Code (NEC) is a standard set of safety requirements for electrical installations in the United States. Section 514.3(B)(2) of the NEC provides requirements for the installation of electrical equipment in Class I, Division 2 locations in motor fuel dispensing facilities.
Class I, Division 2 locations are areas where flammable gases or vapors are present in quantities sufficient to create a hazardous atmosphere. In such locations, it is important to take precautions to prevent the ignition of these gases or vapors, which could result in an explosion or fire.To minimize the risk of ignition, section 514.3(B)(2) requires that electrical equipment in Class I, Division 2 locations at motor fuel dispensing facilities or commercial garages must be installed with at least 10 feet of clearance to any edge, extending in any direction. This clearance is intended to prevent accidental contact with electrical equipment and reduce the risk of sparking or arcing, which could ignite flammable gases or vapors.
Learn more about installation here
https://brainly.com/question/13267432
#SPJ11
___________ is designed to enable the use of normal Web applications on computers and devices with small display screen operating over low speed wireless connections.
The technology you are referring to is called "Mobile Optimization." Mobile optimization is designed to enable the use of normal Web applications on computers and devices with small display screens, operating over low-speed wireless connections.
The domain at the top of the DNS hierarchy is referred to as a top-level domain, or TLD. This refers to DNS on the Internet. The namespace toot zone has the top-level domain installed as well. The top-level domain, which is generally regarded as the best one, is.com. The second and third are.net and.org. However, as mobile device optimisation is necessary, we should choose.com in this case.
A mobile operating system (OS) is a piece of software Mobile Optimization that enables smartphones, tablet PCs, and other devices to run programmes and apps. When a mobile device is turned on, an operating system normally runs, displaying a screen with icons or tiles that display information.
Learn more about Mobile Optimization here
https://brainly.com/question/30626407
#SPJ11
State 3 facts about Aluminum:
1. Aluminum is a chemical element. 2. Aluminum is known for its lightweight and 3. Aluminum has a number of important applications in industries.
Here are three facts about Aluminum:
1. Aluminum is a chemical element with the symbol Al and atomic number 13. It is a soft, silvery-white, nonmagnetic metal that is abundant in the earth's crust.
2. Aluminum is known for its lightweight and strong properties, making it a popular material for a variety of products, from transportation to construction. It is also highly resistant to corrosion, making it an ideal material for use in harsh environments.
3. Aluminum has a number of important applications in industries such as aerospace, automotive, and packaging. In the aerospace industry, for example, aluminum is used in the construction of aircraft due to its strength, light weight, and ability to withstand extreme temperatures. In the automotive industry, it is used to make engine blocks, wheels, and body panels. In packaging, it is commonly used to make beverage cans and food containers.
Know more about the Aluminum
https://brainly.com/question/27885413
#SPJ11
What is the protocol that is used to discover a physical address from a known logical address and what message type does it use?
The protocol used to discover a physical address from a known logical address is Address Resolution Protocol (ARP). ARP uses a message type called ARP request to obtain the physical address corresponding to a logical address.
When an ARP request is sent, it is broadcasted to all devices on the local network, and the device with the matching logical address will respond with an ARP reply containing its physical address.The protocol used to discover a physical address from a known logical address is the Address Resolution Protocol (ARP). ARP uses a message type called an ARP Request to query for the corresponding physical (MAC) address of a given logical (IP) address.
Learn more about physical here
https://brainly.in/question/817604
#SPJ11
What type of firewall security feature limits the volume of traffic from individual hosts?A. Loop protectionB. Network separationC. Stateful inspectionD. Flood guard
The firewall security feature that limits the volume of traffic from individual hosts is called "Flood guard".
This feature is used to prevent denial of service attacks by limiting the amount of traffic that can be sent from a particular host to the network. Stateful inspection is a firewall security feature that examines the traffic and keeps track of the state of each connection.
Loop protection is used to prevent network loops by disabling a port when a loop is detected. Network separation is a security feature that isolates different parts of the network to prevent unauthorized access. The firewall security feature that limits the volume of traffic from individual hosts is D. Flood guard.
Flood guard is designed to prevent excessive traffic or Denial of Service (DoS) attacks by limiting the volume of traffic from individual hosts. This feature helps maintain the stability and security of a network.
Note: While the terms "loop," "stateful," and "firewall" are relevant to network security, they are not directly associated with the specific security feature that limits traffic volume from individual hosts as mentioned in the question.
Learn more about network click here:
brainly.com/question/14276789
#SPJ11
Except in a casr of a concrete encased driven or buried grounding electrode, the connection of a grounding electrode conductor to a grounding electrode shall be ____________.
250.68(a)
According to the National Electrical Code (NEC) 250.68(a), the connection of a grounding electrode conductor to a grounding electrode shall be made in a manner that will ensure a permanent and low-impedance grounding path.
This means that the connection should be made in a way that ensures good conductivity and does not easily loosen or break over time.
The NEC further specifies that the connection should be made by exothermic welding, listed lugs, listed pressure connectors, listed clamps, or other listed means. These methods of connection ensure a reliable and low-impedance grounding path that can withstand the effects of weather, corrosion, and physical stress.
In the case of a concrete encased driven or buried grounding electrode, the connection should be made by one of the methods listed above, and the grounding electrode conductor should be connected to the electrode by welding, brazing, or by use of a listed clamp that exerts pressure on the electrode.
This ensures a reliable and low-impedance grounding path for the system.
Learn more about grounding electrode here:
https://brainly.com/question/31494083
#SPJ11
QUESTION 4
Technician A says that most engine OEMs recommend that customers have the DPF removed and cleaned obce a year to minimize
DPF sintering. Technician B that says that the DPF needs to be actively regenerated at every oil change. Who is correct?
O a. Technician A
b. Technician B
OG Both Technician A and Technician B
O d. Neither Technician A nor Technician B
QUESTION 5
Technician A says that DPFs were used only in HD diesel engines until 2010, when they were replaced with SCR systems.
Technician B says that only a DPF can remove particulate emissions from the exhaust. Who is correct?
O a. Technician A
O b. Technician B
O c. Both Technician A and Technician B
O d. Neither Technician A nor Technician B
Answer to Question 4: Neither Technician A nor Technician B is correct. The Diesel Particulate Filter (DPF) should not be removed and cleaned once a year to minimize DPF sintering. Instead, it should be actively regenerated when it becomes full of soot. There is no need to regenerate the DPF at every oil change.
Answer to Question 5: Technician B is correct. Only a Diesel Particulate Filter (DPF) can remove particulate emissions from the exhaust. However, Technician A is incorrect. DPFs are still used in HD diesel engines, and they were not replaced by Selective Catalytic Reduction (SCR) systems in 2010. Instead, SCR systems are often used in conjunction with DPFs to reduce both particulate matter and NOx emissions.
A counter's input signal can come from an external device such as a sensor. true/false
The given statement "A counter's input signal can come from an external device such as a sensor." is true becasue a counter's input signal can come from an external device such as a sensor.
A counter is a device used to count the number of events or objects that have occurred or passed by a specific point. The input signal to the counter can come from various sources, including sensors, switches, and other devices that can detect the occurrence of an event or the presence of an object.
For example, a conveyor belt in a factory can have a sensor that detects the presence of a product, and sends a signal to the counter to increment the count. In this case, the input signal to the counter comes from the sensor that is external to the counter itself.
Therefore, it is true that a counter's input signal can come from an external device such as a sensor.
You can learn more about counter signal at
https://brainly.com/question/29447930
#SPJ11
Q5)g) Describe the four-step handshake in TCP connection closes.
Answer: The four-step handshake is a process used by the Transmission Control Protocol (TCP) to close a connection between two devices. Here are the steps involved:
1. The first step is initiated by the device that wants to close the connection. This device sends a FIN (finish) packet to the other device, indicating that it is done sending data.
2. The other device receives the FIN packet and sends back an ACK (acknowledgment) packet to confirm that it received the FIN packet.
3. The other device then sends its own FIN packet to the first device, indicating that it is also done sending data.
4. Finally, the first device sends an ACK packet back to the other device to confirm that it received the FIN packet.
Once the four-step handshake is complete, the connection is closed and the devices can no longer communicate using that connection. I hope this helps! Let me know if you have any other questions.
Hi! I'd be happy to help you understand the four-step handshake in TCP connection closures. The four-step handshake, also known as the TCP connection termination process, is a series of steps that ensures a reliable and orderly closing of a TCP connection between two devices. Here's a step-by-step explanation:
1. **FIN (Finish) Packet**: The device initiating the termination sends a TCP packet with the FIN flag set to the receiving device, indicating its intention to close the connection. This means the sender has finished transmitting data.
2. **ACK (Acknowledgment) Packet**: The receiving device acknowledges the FIN packet by sending an ACK packet back to the sender. The ACK packet has an acknowledgment number that is one greater than the received sequence number, confirming the receipt of the FIN packet.
3. **FIN (Finish) Packet from the receiving device**: After sending the ACK packet, the receiving device sends its own FIN packet to the sender, signaling that it has also finished transmitting data and is ready to close the connection.
4. **ACK (Acknowledgment) Packet from the sender**: The sender acknowledges the receiving device's FIN packet by sending a final ACK packet. The acknowledgment number is one greater than the received sequence number, confirming receipt of the FIN packet from the receiving device.
Once this process is completed, the TCP connection is terminated, and both devices can release the associated resources. The four-step handshake ensures that both devices have finished transmitting data and are ready to close the connection in a reliable and orderly manner.
Learn more about connection here brainly.in/question/3996940
#SPJ11
Explanation:
The four-step handshake, also known as the TCP connection termination process, is a series of steps that ensures a reliable and orderly closing of a TCP connection between two devices. Here's a step-by-step explanation:
1. **FIN (Finish) Packet**: The device initiating the termination sends a TCP packet with the FIN flag set to the receiving device, indicating its intention to close the connection. This means the sender has finished transmitting data.
2. **ACK (Acknowledgment) Packet**: The receiving device acknowledges the FIN packet by sending an ACK packet back to the sender. The ACK packet has an acknowledgment number that is one greater than the received sequence number, confirming the receipt of the FIN packet.
3. **FIN (Finish) Packet from the receiving device**: After sending the ACK packet, the receiving device sends its own FIN packet to the sender, signaling that it has also finished transmitting data and is ready to close the connection.
4. **ACK (Acknowledgment) Packet from the sender**: The sender acknowledges the receiving device's FIN packet by sending a final ACK packet. The acknowledgment number is one greater than the received sequence number, confirming receipt of the FIN packet from the receiving device.
Once this process is completed, the TCP connection is terminated, and both devices can release the associated resources. The four-step handshake ensures that both devices have finished transmitting data and are ready to close the connection in a reliable and orderly manner.
Learn more about connection here brainly.in/question/3996940
#SPJ11
Currently, the United StatesChoose one:A. recovers 90% of the oil from each well drilled.B. imports more than half of the oil it uses.C. is finding huge new oil resources in new geologic areas, such as igneous deposits.D. is the site of most of the 25 known supergiant oil fields.
Currently, the United States imports more than half of the oil it uses. While the United States is still a significant producer of oil, it is not able to meet all of its domestic demand and relies on imports from other countries to make up the difference.
Oil, also known as petroleum, is a fossil fuel that is formed from the remains of ancient plants and animals that lived millions of years ago. It is a complex mixture of hydrocarbons that is typically found in underground reservoirs or rock formations. Oil is a critical resource that is used to power transportation, generate electricity, and manufacture a wide range of products, including plastics, fertilizers, and chemicals. However, the extraction, transportation, and use of oil can have negative environmental and social impacts, such as air and water pollution, habitat destruction, and climate change. As a result, there has been increasing interest in finding alternative sources of energy that are more sustainable and less harmful to the environment.
Learn more about the oil here:
https://brainly.com/question/30807592
#SPJ11
In Class I - Division 1 locations, the entry shall be metric designator trade size ___________ or larger and the enclosure contains terminals splices, ot taps.
501.15
In Class I - Division 1 locations, the entry shall be metric designator trade size 21.0 or larger and the enclosure contains terminals splices, or taps. This requirement is outlined in section 501.15 of the National Electrical Code (NEC).
For such more question on hazardous
https://brainly.com/question/29232461
#SPJ11
It is okay to download information without asking a lab instructor as long as it is for your online class. true
false
False. It is advisable to follow guideline outline by the lab or consult the lab instructor before downloading.
Why are some of the guideline in place for student when downloading?There may be unique guidelines and limitations on obtaining data or visiting particular websites at some institutions or labs. To avoid any potential problems, always verify with your lab instructor or follow the specified instructions.
These download guidelines have been put in place to avoid downloading information that might be considered sensitive, illegal, or detrimental to the operating systems.
Find more exercises on download information guidelines;
https://brainly.com/question/30024121
#SPJ4
The output of a PLC counter is energized when the:a. accumulated count equals the preset count.b. preset count is greater than the accumulated count.c. counter input rung is true.d. counter input rung is false.
The correct answer is (a) accumulated count equals the preset count.
PLC (Programmable Logic Controller) counters are used in automation systems to count the number of events or occurrences of an input signal.
The output of a counter is energized when the count reaches a predetermined value set by the programmer, which is known as the preset count.In other words, the counter accumulates the number of events as they occur and compares it with the preset count. When the accumulated count equals the preset count, the counter output is energized, indicating that the predetermined number of events has been reached.The counter input rung determines when the counter starts counting and when it stops. If the input rung is true, the counter will start counting, and if the input rung is false, the counter will stop counting. However, this does not affect the output of the counter directly.In conclusion, the output of a PLC counter is energized when the accumulated count equals the preset count. This is the most important condition to be met for the counter to activate its output. The counter input rung determines when the counter starts and stops counting, but it does not affect the output of the counter directly.For such more question on automation
https://brainly.com/question/30088157
#SPJ11
True or False? although inductive current lags inductive voltage by 90°, both waves have the same frequency.
The answer to the question: "True or False? although inductive current lags inductive voltage by 90°, both waves have the same frequency."
True, although inductive current lags inductive voltage by 90°, both waves have the same frequency.
Learn more about current lags: https://brainly.com/question/24858512
#SPJ11
T/F : All cleared DoD civilian, military, and contractor personnel who generate or create classified material from
authorized classified sources are derivative classifiers.
True. All cleared DoD civilian, military, and contractor personnel who generate or create classified material from authorized classified sources are derivative classifiers.
The United States Department of Defense (DoD) is a federal agency responsible for providing the military forces needed to deter war and protect the security of the country. The DoD is the largest employer in the world, with over 1.3 million active-duty service members, more than 800,000 civilian personnel, and over 800,000 reserve and National Guard members. The DoD operates under civilian control and is led by the Secretary of Defense, who is a member of the President's Cabinet. The department's responsibilities include providing military forces for the protection of the nation, managing military operations and readiness, conducting research and development, and managing military installations and facilities. The DoD also works closely with other federal agencies, including the Department of State and the Department of Homeland Security, to coordinate national security efforts.
Learn more about DoD here:
https://brainly.com/question/30324752
#SPJ11
What are the benefits of having operator functions that perform object conversion?
Operator functions that perform object conversion, such as type casting or coercion, offer several benefits in programming:
1. Flexibility: They allow you to work with multiple data types, converting between them as needed, to avoid compatibility issues or make your code more versatile.
2. Readability: By explicitly stating the conversion, your code becomes more readable and understandable for others, as the intention behind the conversion is clear.
3. Safety: By using operator functions for conversion, you can handle data type errors or exceptions in a controlled manner, ensuring the stability and reliability of your code.
4. Reusability: Implementing conversion functions within an object or class enables you to reuse the same conversion logic across your codebase, leading to consistent behavior and easier maintenance.
5. Efficiency: By using built-in conversion functions or overloading operators, you can optimize performance by minimizing the overhead of type conversions.
Learn more about Operator functions from : brainly.com/question/27915566
#SPJ11
(370-2) Cablebus is ordinarily assembled at the _____.
(370-2) Cablebus is ordinarily assembled at the manufacturing plant. Manufacturing overhead does not include the depreciation on delivery trucks, but it does include all other possibilities that are still available.
Delivery truck depreciation is not included in the costs associated with making computers. Manufacturing plant overhead, also known as factory burden, factory overhead, or production overhead, is the umbrella term for all costs associated with manufacturing, including electricity costs, costs for factory supplies and indirect labour, rent, insurance, costs for heating, water, and other forms of energy, salaries, and expenses for cleaning, oiling, lubricating, servicing, and repairs.
Manufacturing overhead does not include the depreciation on delivery trucks, but it does include all other possibilities that are still available.
The total of all indirect material, labour, and other costs that are not directly related to the goods and units produced at a manufacturing facility is manufacturing overhead. These are equally distributed to each generated unit.
Learn more about manufacturing plant here
https://brainly.com/question/15071443
#SPJ11
Interior metal water piping located more than ______ feet from the point of entrance to the building shall not be used as part of the grounding electrode system.
Interior metal water piping located more than 5 feet from the point of entrance to the building shall not be used as part of the grounding electrode system. This is because the farther the interior metal water piping is from the entrance point.
The less effective it is at conducting electrical currents and providing a stable grounding connection. It is important to have a proper grounding electrode system in place to protect against electrical hazards and ensure the safe operation of electrical equipment.
According to the National Electrical Code (NEC), interior metal water piping located more than 5 feet from the point of entrance to the building shall not be used as part of the grounding electrode system.
Learn more about the electrodes here:- brainly.com/question/17060277
#SPJ11
A particular telnet site does not appear to be responding on a Windows 7 computer. What command could the technician use to show any cached DNS entries for this web page?
The technician could use the "ipconfig /displaydns" command in the command prompt to show any cached DNS entries for the telnet site.
The technician could use the "ipconfig /displaydns" command in the command prompt to show any cached DNS entries for the telnet site. This will display a list of all recently accessed DNS entries, including the telnet site in question. If the entry is outdated or incorrect, the technician can then flush the DNS cache using the "ipconfig /flushdns" command to ensure that the computer obtains the correct DNS information for the telnet site.
Learn more about command here
https://brainly.com/question/30319932
#SPJ11
Which three IP addresses are private? (choose three)
The three IP addresses that are private are 10.0.0.0, 172.16.0.0, and 192.168.0.0. These are reserved IP addresses that are not used for public internet communication and can only be used within a private network.
Public IP addresses, on the other hand, are used for internet communication and are unique to each device connected to the internet.
There are three IP address ranges that are considered private:
1. 10.0.0.0 to 10.255.255.255
2. 172.16.0.0 to 172.31.255.255
3. 192.168.0.0 to 192.168.255.255
These IP address ranges are reserved for private use within local networks and are not routable on the public internet.
Learn more on IP Addresses here :
brainly.com/question/30781274
#SPJ11
Which type of wireless security makes use of dynamic encryption keys each time a client associates with an AP?
The type of wireless security that makes use of dynamic encryption keys each time a client associates with an AP is called WPA2-PSK or WPA2-Enterprise.
The type of wireless security that makes use of dynamic encryption keys each time a client associates with an AP is called WPA2-PSK (Wi-Fi Protected Access 2 with Pre-Shared Key) or WPA2-Enterprise. These encryption keys are generated on the fly and are unique to each client and session, which greatly enhances the overall security of the wireless network. This type of security is particularly effective against unauthorized access attempts and eavesdropping attacks, as it ensures that the data transmitted over the wireless network is always encrypted and protected.
Learn more about encryption keys here
https://brainly.com/question/29572224
#SPJ11
Every class in Java, except ________, extends an existing class.a. Integer.b. Object.c. String.d. Class.
Every class in Java, except the "Object" class (option b), extends an existing class. The Object class is the base of the Java class hierarchy and does not extend any other class.
The four common types of struck by hazard are: Struck-by Flying objects, Struck-by falling objects, Struck-by swinging objects and Struck-by rolling objects. Struck-by hazard occur when a worker comes into forcible contact with a flying, falling, swinging or rolling object. However, these type of hazard continue to cause many fatalities and serious injuries every year and some even leads to the eventual death of construction workers. A struck by hazard is caused by forcible contact or impact between the injured person and an object or piece of equipment.
Learn more about object here
https://brainly.com/question/14964361
#SPJ11
What types of memory can be used on a 100-MHz motherboard?
The specific type of memory that can be used on a 100-MHz motherboard depends on the motherboard's memory controller and the type of memory slots that it has.
A motherboard with a 100-MHz front-side bus (FSB) speed typically requires memory that can operate at a speed of 100 MHz or lower.
The most common types of memory that can be used on a 100-MHz motherboard are:
SDRAM (Synchronous Dynamic Random Access Memory):
This type of memory was commonly used in computers with 100-MHz FSB speeds.
SDRAM can operate at speeds of up to 133 MHz and comes in various capacities, ranging from 64 MB to 1 GB.
EDO RAM (Extended Data Out Random Access Memory):
This type of memory was used in some older computers with 100-MHz FSB speeds.
EDO RAM operates at a speed of 66 MHz and comes in capacities ranging from 4 MB to 256 MB.
FPM RAM (Fast Page Mode Random Access Memory):
This type of memory was commonly used in older computers with 100-MHz FSB speeds.
FPM RAM operates at a speed of 66 MHz and comes in capacities ranging from 4 MB to 256 MB.
Buffered and Registered memory:
These are specialized types of memory that are typically used in servers and workstations.
Buffered and Registered memory are designed to improve reliability and stability in high-performance systems, but they may not be compatible with all motherboards.
It is always recommended to check the motherboard's specifications or consult the manufacturer's documentation before purchasing memory for the system.
For similar questions on memory
https://brainly.com/question/31434818
#SPJ11
Bending radius in type AC shall be made not to be damaged and of the curve of the inner edge of any bend shall not be less than _________ times in diameter of the cable.
325.24
The bending radius in type AC cable should be made to prevent damage, and the curve of the inner edge of any bend should not be less than 5 times the diameter of the cable, as specified in the NEC section 320.24.
Pull the cord to unplug them from the outlet was one of the other answers to the question. Carry them by the cord, option C. D) Keep them close to outlets and on the prevent damage work table in a location that is simple to reach.
Read the manufacturer's directions for proper usage and maintenance of your tools to avoid harm.
These days, tools are pricey. Because of this, if you want to use them for a long time, you must take good care of them and use them appropriately. You must first study the manufacturer's instructions for the use and upkeep of the tool because of its complexity. By doing so, you'll make the most of their potential and employ them more effectively for the right tasks.
Learn more about prevent damage here
https://brainly.com/question/11156977
#SPJ11
a wireless engineer is interested in using an antenna that is commonly used in
A wireless engineer may be interested in using a dipole antenna, which is commonly used in various wireless communication applications. The dipole antenna is easy to construct and can be used for both transmitting and receiving signals. It is a popular choice for applications such as Wi-Fi, Bluetooth, and radio communication.
Identify the requirements: The wireless engineer needs to determine the frequency range, gain, radiation pattern, and polarization required for the specific application. Research common antenna types: Some commonly used antennas include dipole, monopole, Yagi-Uda, and patch antennas. Each type has its advantages and limitations based on the desired application.
Select the appropriate antenna: After comparing the different antenna types, the wireless engineer will choose the one that best fits the requirements and constraints of the project. Design and implementation: The engineer will design the chosen antenna according to the desired specifications, taking into account factors such as size, material, and mounting options. Test and optimize.
In summary, a wireless engineer commonly selects and implements an antenna by identifying the requirements, researching common antenna types, selecting the most suitable option, designing and implementing the antenna, and testing and optimizing its performance.
To know more about wireless engineering:- https://brainly.com/question/28141205
#SPJ11
A wireless engineer may be interested in using a commonly used antenna such as a dipole antenna or a patch antenna.
These types of antennas are popularly used in wireless communication systems due to their ability to provide a directional or omnidirectional signal pattern, depending on the design. Additionally, they are relatively easy to construct and tune for specific frequencies, making them a cost-effective solution for many applications.
Learn more about used antenna: https://brainly.com/question/29846891
#SPJ11
When a metal underground water pipe is used as a grounding electrode, the pipe shall be electronically continuous and in direct contact with the eart for at least _____ feet.
250.52(a)(1)
According to the National Electrical Code (NEC) 2021 edition, when a metal underground water pipe is used as a grounding electrode, the pipe shall be electrically continuous and in direct contact with the earth for at least 10 feet.
The purpose of this requirement is to ensure that the metal water pipe provides a low-resistance path to ground for electrical current in the event of a fault or surge in the electrical system. The 10-foot minimum length requirement helps to ensure that the metal water pipe is in good contact with the earth and can effectively dissipate any electrical energy that may be present. It is also important to note that the metal water pipe must be supplemented by additional grounding electrodes as necessary to meet the requirements of the NEC. These may include driven rods or plates, concrete-encased electrodes, or other approved grounding electrodes, depending on the specific circumstances of the installation.
Learn more about underground water here:
https://brainly.com/question/30025861
#SPJ11
Three way and four way switches shall be so wired that all switching is done only in the _______ circuit conductor.
404.2(a)
According to the National Electrical Code (NEC) 404.2(a), three-way and four-way switches shall be wired so that all switching is done only in the ungrounded (hot) circuit conductor. This means that the switched conductor, or the wire that is connected to the load being switched, should not be connected directly to any switch.
Instead, in a three-way switch configuration, two switches are used to control a single load. The two switches are connected to the ungrounded (hot) circuit conductor and a traveler wire, which carries the ungrounded (hot) circuit conductor between the switches. The load is then connected to the switched conductor, which is connected to one of the travelers.
In a four-way switch configuration, three or more switches are used to control a single load. In this case, the switches are connected to the ungrounded (hot) circuit conductor and two or more traveler wires, which carry the ungrounded (hot) circuit conductor between the switches. The load is then connected to the switched conductor, which is connected to one of the travelers.
By wiring the switches in this way, all switching is done in the ungrounded (hot) circuit conductor, which ensures that the circuit is properly protected by overcurrent devices and that there is no danger of shock or electrocution from the switched conductor.
Learn more about switched conductor here:
https://brainly.com/question/29869573
#SPJ11
It is okay to download information without asking a lab instructor as long as it is for your online class. true
false
Answer: It is false
Explanation:
Because if you was an kid and you were looking at violent stuff then your parent or guardian catch you looking at it you will be in troble.
What is the advantage of taking the output from the stator in a rotating field altenator? the brushes do not have to handle the ouput current.
An alternator is an electrical generator that converts mechanical energy into electrical energy. The output of the alternator is typically alternating current (AC), which is produced by rotating a magnetic field within the stator.
A rotating field alternator current changes the flow in the output windings by rotating the magnetic field around the stator. In a rotating field alternator, one notable benefit of taking the output from the stator is that the brushes are not required to manage the output current. Electrical contacts called brushes are used by the generator's stationary and revolving components to transfer electricity. The large currents and friction produced during operation cause the brushes in conventional generators to deteriorate over time. The brushes are removed when the output is taken straight from the stator windings, lowering maintenance requirements and boosting generator dependability.
A rotating field alternator also has the benefit of generating a more reliable and consistent
Learn more about alternating current (AC) here
https://brainly.com/question/30675305
#SPJ11