The electronegativitie of the period-3 element are lited on the tranparency.. Si and Cl is 0.7, . Mg and S is 1.3, Si and S is 1.7, Al and P is 1.6.
The electronegativity of the atoms that make up the bond determines whether it is nonpolar or polar covalent. An atom's propensity to draw electrons (or electron density) in its direction is measured by its electronegativity. It controls how the shared electrons between the two atoms in a bond are distributed. The more an atom's electronegativity, the more strongly the electrons in its bonds are drawn to it. In a polar covalent bond, electrons are pushed in the direction of the more electronegative atom; as a result, the atom with the partial negative charge is the more electronegative atom. The electron distribution becomes increasingly polarised and the atoms' partial charges increase with increasing electronegativity differences.
Learn more about electronegativity here:
https://brainly.com/question/29810769
#SPJ4
What is the wet bulb temperature if the dry bulb is 26 °C and the relative humidity is 77%?
The wet bulb temperature if the dry bulb is 26 °C and the relative humidity is 77% is 16°C.
What is relative humidity ?Relative Humidity (RH) is a ratio of the quantity of atmospheric moisture that is actually present to the amount that would be present if the air were saturated, expressed in percent.
In relation to the maximum amount of water vapor that the air can hold at a specific temperature. A value of 50% relative humidity, for instance, indicates that there is only 50% as much water vapor present as there would be if the air were saturated at that temperature.
Td = T - ( 100 - RH ) ÷ 5.)
where, Td is dew point temperature, T is observed temperature, and RH is relative humidity.
by using the above formula
Td=26 - ( 100 - 50 ) ÷ 5
=26 - 50 ÷ 5
=26-10
Td = 16°C
Thus, The wet bulb temperature if the dry bulb is 26 °C and the relative humidity is 77% is 16°C.
To learn more about relative humidity, follow the link;
https://brainly.com/question/22069910
#SPJ1
2. a) use the ph scale to describe an acidic solution and a basic solution. 2. b) at what ph would a solution be considered neutral? why?
a. The pH scale on a solution that describes acidity is less than 7, and alkaline is more than 7.
b. The solution is considered neutral when the pH is 7
pH a is the degree of acidity or alkalinity of a solution from the value of the concentration of hydrogen and hydroxyl ions in it.
A solution is said to have an acidic pH if it has a pH of less than 7. The lower the pH of a solution, the more acidic the solution is. While a solution is said to be alkaline if it has a pH of more than 7. The higher the pH value of the solution, the more alkaline the solution is.
A solution is said to have a neutral pH if the value is 7. A pH value of 7 is said to be neutral because in pure water dissolved H+ ions and dissolved OH- ions are in the same amount.
Learn more about pH at:
https://brainly.com/question/15289714
#SPJ4
The ionic compound containing ammonium ion and carbonate ion gives off the odor of ammonia, a property put to use in smelling salts for reviving someone who has fainted.
a. True
b. False
True, The ionic combination of ammonium ion as well as carbonate ion emits an ammonia-like scent, which is used in smelling salts to revive fainting people.
The ionic compound with the formula (NH4)2CO3 emits the scent of ammonia and is used in smelling salts to revive fainting people since it contains the ammonium ion & carbonate ion.
To avoid or treat fainting, use aromatic ammonia spirit. An uncomfortable or stressful incident, a medication, or a significant medical condition like heart disease can all contribute to fainting.
Syncope, often known as fainting, is a loss of awareness brought on by a vagal reflex-induced slowing of the heart rate.
Learn more about Ammonium Carbonate at
https://brainly.com/question/13915102?referrer=searchResults
#SPJ4
a sodium cation is than a sodium atom. a phosphorus anion is than a phosphorus atom. a magnesium ion is than a sodium ion. a chlorine ion is than a phosphorus ion. a potassium ion is than a sodium ion.
The following conclusions can be drawn from using the periodic table to compare the sizes of ionic radii to the equivalent atomic radii or other ionic radii.
Compared to sodium atoms, sodium cations are smaller.An anion of phosphorus is bigger than an atom of phosphorus.Compared to sodium ions, magnesium ions are smaller.In comparison to phosphorus, chlorine is a smaller ion.Compared to sodium ions, potassium ions are bigger.The nuclear pull is greater for the magnesium atom since it has a higher atomic number than sodium but the same number of shells. Its size is therefore smaller than sodium's. When an electron is added to an atom to form an anion, the new electron repels other electrons, increasing the size of the ion. This is why phosphorus ions are larger than phosphorus atoms.
To learn more about periodic table click here https://brainly.com/question/11155928
#SPJ4
how many ml of 0.150 m ca(oh)2(aq) will be required to completely react with 150. ml of 0. 100 m h3po4(aq) solution.
4.86 ml are required to fully react with 11.73 ml of 1.006 m ca(oh)2 in order to complete the reaction.
provided information to be calculated:
Using Ca3(PO4)2 (s) + 6H2O, one can calculate: 2H3PO4 + 3Ca(OH)2 (aq)
cal mols
7.33 moles of H3PO4 in a volume of 1 ml are needed to replace the 2 existing H3PO4; 7.33/1.508 = 4.86.
How do moles respond to a volume increase?
An increase in volume advantages the direction that produces more moles of gas, and because there are more moles of products in this situation, the reaction will move to the right and produce more moles of products.
Learn more about ca(oh)2 here:
https://brainly.com/question/29347053
#SPJ4
an atom of fe has two 4s electrons and six 3d electrons. how many unpaired electrons would there be in a fe2 ion?
Two 4s electrons and six 3d electrons make up one atom of fe. A fe2 ion would have FOUR unpaired electrons.
1s2 2s2 2p6, 3s2 3p6, and 4s2 3d6 make up the electrical configuration of fe.Thus, there are four unpaired electrons in the third subshell.This demonstrates fe's paramagnetic properties.Both the 3d and 4s orbitals have almost the same energy. It's also important to note that, in contrast to the other orbitals, the third orbital has a single pair of electrons. Iron exists in two valence states, +3 and +2, as was previously mentioned. As a result, when it loses the two 4s electrons, it gets a valency of +2.
To know more about electrical configuration please click on the link brainly.com/question/1688387
#SPJ4
the crystal field splitting energy depends on the structure of the complex. group of answer choices true false
The crystal field splitting energy depends on the structure of the complex is a correct statement.
The energy difference between ligand d orbitals is what causes crystal field splitting. The capital Greek letter is used to represent the crystal field splitting number. The difference in color between two related metal-ligand complexes is explained by crystal field splitting, increases down a group on the periodic table and tends to rise with oxidation number. The propensity of transition metals to form complexes is one of their key characteristics. A complex can be thought of as having several ligands encircling a central metal atom or ion. Crystal field theory governs how these ligands interact with the main metal atom or ion. The interaction between a metal ion and ligand is regarded by the 1929-founded crystal field theory as purely an electrostatic phenomenon.
To know more about crystal field theory visit :https://brainly.com/question/29389010
#SPJ4
the heat of vaporization of water at 100°c is 40.66 kj/mol. calculate the quantity of heat that is absorbed/released when 7.00 g of steam condenses to liquid water at 100°c.
the heat of vaporization of water at 100°c is 40.66 kj/mol, Heat of vaporisation (HV) = q/m = 40.66 kJ/mol, quantity of heat is = 20.33 kjoules
q is heat absorbed or released , m is mass = 9 g, no. of moles of water = mass/mol wt = 9/18 = 0.5 moles, HV x m = q, uantity of heat is = 40.66 x 0.5 = 20.33 kjoule. The enthalpy of vaporisation, also known as the heat of vaporisation or heat of evaporation, is the amount of energy required to convert a liquid substance into a gas. The enthalpy of vaporisation depends on the pressure at which the transformation occurs. The heat of vaporisation is defined as the amount of heat required to convert 1g of a liquid into a vapour without causing the liquid's temperature to rise. Boiling refers to vaporisation at the boiling point. A boiling liquid's temperature remains constant until all of the liquid has been converted to a gas.
Learn more about vaporization here:
https://brainly.com/question/9967928
#SPJ4
. absorbance readings of four prepared tubes with various solutions over a 6060-minute period. question which of the following best justifies the use of tube 22 as a control treatment? responses it was a negative control for the accuracy of the spectrophotometer, ensuring that an accurate reading for treatment cuvette 22 would be made. it was a negative control for the accuracy of the spectrophotometer, ensuring that an accurate reading for treatment cuvette 2 would be made. it was a negative control for the chemical stability of the chlorophyll suspension, ensuring that changes in absorbance could only be attributed to changes in chlorophyll content. it was a negative control for the chemical stability of the chlorophyll suspension, ensuring that changes in absorbance could only be attributed to changes in chlorophyll content. it was a positive control for the change in dcpipdcpip color associated with changes in light intensity. it was a positive control for the change in d c p i p color associated with changes in light intensity. it was a positive control for measuring the effect of dcmudcmu on the reaction.
The use of tube 22 as a control treatment best justifies that it was a positive control for measuring the effect of DCMU on the reaction.
DCMU acts as an inhibitor to the movement of electrons within the light reaction of photosynthesis. The major role of control tube is to reduce the variability due to unwanted/unknown factors of the experiment. Controls are used to make sure that test results are not positive or negative due to some unknown factor. A control group is used to establish causality by isolating the effect of an independent variable. Here, researchers change the independent variable in the treatment group and keep it constant in the control group. Then they compare the results of these groups.
Thus, the best use is that it was a positive control for measuring the effect of DCMU on the reaction.
To learn more about control tube check the link below:
https://brainly.com/question/14941384
#SPJ4
(Multiple answers possible. Mark all that apply.)
In the electron configuration 2 8 18 6 for element 34, Selenium:
The octet rule has been satisfied for the second shell.
There are eight electrons in p orbitals.
There are eight electrons in the second electron shell
There are eight ways to put electrons into the second shell.
In the electron configuration 2 8 18 6 for element 34, Selenium:
The statement that applies include:
The octet rule has been satisfied for the second shell.There are eight electrons in p orbitals.There are eight electrons in the second electron shellWhat is selenium?Selenium is a chemical element with the symbol Se and atomic number 34 and a nonmetal with properties that are intermediate between the elements above and below in the periodic table, sulfur and tellurium, and also has similarities to arsenic.
The octet rule refers to the chemical rule of thumb which states that the tendency of atoms to prefer to have eight electrons in the valence shell.
learn more about selenium at:
https://brainly.com/question/24439924
#SPJ1
when aluminum metal reacts with hcl(aq), the products formed are alcl3(aq) and hydrogen. if 0.159 moles of aluminum undergo this reaction with an excess of hydrochloric acid, how many grams of hydrogen gas should be produced?
0.321 g of hydrogen gas should be produced in this reaction.
To answer this question, we need to first calculate the number of moles of hydrogen gas produced when 0.159 moles of aluminum reacts with an excess of hydrochloric acid. Since the reaction is:
Al + HCl → AlCl3 + H2
The number of moles of hydrogen gas produced will be equal to the number of moles of aluminum used, i.e. 0.159 moles.
Next, we need to convert this number of moles of hydrogen gas to the number of grams of hydrogen gas. For this, we use the molar mass of hydrogen gas, which is 2.02 g/mol.
Therefore, the number of grams of hydrogen gas produced when 0.159 moles of aluminum reacts with an excess of hydrochloric acid is:
0.159 moles * 2.02 g/mol = 0.321 g.
Hence, the answer is 0.321 g of hydrogen gas.
For more questions like Aluminum reaction click the link below:
https://brainly.com/question/28146386
#SPJ4
A newly discovered gas, gas Q, travels 3.40 times faster than carbon dioxide. What is the molar mass of gas Q?
Answer:6.241
Explanation :Step 1: List the known quantities and plan the problem.
Step 2: Solve. n=PVRT=0.987atm×0.677L0.08206L⋅atm/K⋅mol×296K=0.0275mol. Now divide g by mol to get the molar mass. ...
Step 3: Think about your result. The R value that corresponds to a pressure in atm was chosen for this problem.
calculate the mass defect in fe-56 if the mass of an fe-56 nucleus is 55.921 amu. the mass of a proton is 1.00728 amu and the mass of a neutron is 1.008665 amu, and the mass of an electron in 0.00055 amu
The mass defect in Fe-56 is equal to 0.52823 amu.
What is Mass Defect?The mass defect can be defined as the difference between the actual atomic mass and the theoretical mass calculated by addition of the mass of protons and neutrons in the nucleus.
The actual atomic mass is always less than the predicted mass determined by adding the masses of nucleons. This additional mass is due to the binding energy that is released when a nucleus is formed.
[tex]\triangle M = (Zm_p + Nm_n) - M_A[/tex]
Given the mass of the proton = 1.00728 amu
The given mass of a neutron = 1.008665 amu
The given mass of an electron = [tex]0.00055 amu[/tex]
The mass of an Fe-56 nucleus = 55.921 amu
The mass defect for Fe-56 can be calculated as:
[tex]\triangle M = (26\times 1.00728 + 30 \times 1.008665) - 55.921[/tex]
ΔM = 0.52823 amu
Learn more about mass defect, here:
https://brainly.com/question/11624098
#SPJ1
when a h atom absorbs an ultraviolet photon with the correct energy, what transition can the electron in the atom undergo?
When an H atom absorbs an ultraviolet photon with the correct energy, the electron in the atom can undergo a transition from the fifth energy level (n=5) to the first energy level (n=1).
This type of transition is called a "quantum jump" and is associated with the emission of a photon. When an H atom absorbs an ultraviolet photon with the correct energy, it will move from its ground state to an excited state.
This excitation of the electron can then lead to further processes such as the emission of a photon or the formation of an ion-pair. Therefore the correct answer is D)n=5 to n=1 when the H atom absorbs an ultraviolet photon with the correct energy
For more questions like H atom click the link below:
https://brainly.com/question/29654695
#SPJ4
complete question:
when a H atom absorbs an ultraviolet photon with the correct energy, what transition can the electron in the atom undergo?
A)n=1 to n=5
B)n=2 to n=6
C)n=6 to n=2
D)n=5 to n=1
1
2
18 6
In an experiment, a student found the percent by mass of water in a sample of BaCl₂ + 2H₂O to be 17.4%. If the accepted value is 14.8%, the percent error in
the student's result is equal to
3.
26
17.4
x100
26
14.8
-x100
14.8
17.4
x100
17.4
14.8
x100
K
[8]
Submit Answer
B
1
Calculator
Ruler
9592
Protractor
Listen
The percent error in the student's result is equal to 17.57 %.
How to calculate the percent error?Percent error can be described as the difference between the estimated value and the actual value in comparison to the actual value and is represented as a percentage. In other words, the percentage error can be defined as the relative error multiplied by 100.
The mathematical formula for percent error can be defined as:
P.E. = (|Estimated value - Actual value|/ Actual value) × 100
[tex]\displaystyle \delta = \left| \frac{v_A - v_E}{v_A} \right| \cdot 100\%[/tex]
Given, the estimated value = 17.4
The actual value = 14.8
[tex]\displaystyle \delta \% = \left| \frac{14.8 - 17.6}{14.8} \right| \cdot 100\%[/tex]
Percent error = 17.57 %
Learn more about Percent error, here:
https://brainly.com/question/3105259
#SPJ1
a balloon is filled and sealed with air at sea level. if the balloon is taken to a city at 12,000 ft above sea level, what could be the result
As long as the temperature and amount of gas inside the balloon remain constant, the balloon will expand in volume as it flies above sea level.
When a balloon is at sea level, what happens to it?The lower pressure in the upper atmosphere, caused by the lower pressure in the upper atmosphere's upper atmosphere, permits the balloon to expand since there is less material pushing back on it.
Does the balloon's volume change, stay the same, or become larger or smaller?As the internal and external pressures become equal, the inside gas of the balloon expands because the atmospheric gas places less pressure on the balloon's surface.
To know more about temperature visit :-
https://brainly.com/question/15267055
#SPJ4
a gas in a closed rigid container exerts a pressure of 1.20 atm at 20.0 oc. when heated, the pressure is 1.50 atm. what is the temperature of the heated gas? provide answer in oc to the nearest 0.1 oc. g
A gas in a closed rigid container exerts a pressure of 1.20 atm at 20.0 °C. when heated, the pressure is 1.50 atm. the temperature of the heated gas is 25 °C
given that :
pressure of the gas P1 = 1.20 atm
temperature of the gas T1 = 20 °C
The pressure of the gas P2 = 1.50 atm
temperature of the gas T2 = ?
according the gay - Loussac law , we get:
P1 / T1 = P2 /T2
T2 = P2 T1 / P1
T2 = (1.50 × 20 ) / 1.20
T2 = 25 °C
the temperature T2 = 25 °C
To learn more about pressure here
https://brainly.com/question/29144840
#SPJ4
describe the different characteristics between metals, nonmetals, and metalloids on the periodic table.
if electrons are received from only glycolysis, how many molecules of oxygen can be reduced by one glucose molecule?
Hence one molecule of oxygen can be reduced by one glucose molecule, if electrons are received from only glycolysis
The balanced chemical equation for the conversion of glucose to pyruvate shows that four hydrogen atoms (four protons and four electrons) are also formed:
CH 206 — 2 CH3-C-C-OH + 4H+ + 4e Glucose Pyruvate
Since there could be 4 lectrons and 4 hydrogens from one molecule of that are from glucose to pyruvate step.
O2 + 4H+ + 4e- = 2H2O
Hence one molecule of oxygen can be reduced .The method by which glucose is metabolised to create energy is known as glycolysis. It generates water, ATP, NADH, and two pyruvate molecules. It doesn't need oxygen to happen since it happens in a cell's cytoplasm. In both aerobic and anaerobic species, it happens.
Learn more about oxygen here:
https://brainly.com/question/13370320
#SPJ4
given the balanced equation: 2 n2h4(l) n2o4(l) 3 n2(g) 4 h2o(g) a) how many grams of dinitrogen tetrahydride are required to produce 57 moles of nitrogen?
Dinitrogen tetrahydride must be converted into 38 moles [tex]N_2H_4[/tex] in order to yield 57 moles of nitrogen.
[tex]x molN_2H_4= 57mol N_2(\frac{2 molN_2O_4}{3 molN_2} )\\x molN_2H_4= 19*2 molN_2H_4\\x mol N_2H_4= 38 mol N_2H_4[/tex]
Dinitrogen tetroxide is the chemical molecule N2O4, also known as nitrogen tetroxide (NTO) and occasionally amyl (typically among ex-USSR/Russian rocket engineers). It is a helpful reagent in the synthesis of chemicals. It and nitrogen dioxide combine to form an equilibrium combination. It has a 92.011 g/mol molar mass.
Dinitrogen tetroxide is a potent oxidizer that spontaneously reacts when it comes into touch with different types of hydrazine, making the two a popular bipropellant for rockets.
To learn more about moles, refer:-
https://brainly.com/question/26416088
#SPJ4
1. Iron ores are rocks and minerals from which metallic iron can be economically extracted. Hematite is an iron ore with
the formula Fe2O3. What is the minimum mass of Fe2O3, in kg, is necessary to contain 1.50 kg of Fe?
2. Aluminum (Al) reacts with oxygen (O2) to yield aluminum oxide. In a reaction, 2.91 g of Al reacted with oxygen to
form 5.50 g aluminum oxide. Calculate the empirical formula of aluminum oxide?
3. What is the minimum amount of LiCl, in grams, necessary to react with 106 g of Pb(C2H3O2)2?
4. In the combustion of octane (C8H18), octane reacts with oxygen. What is the mass of CO2 (in g) that is produced from
the complete combustion of 60.3 g of C8H18?
1) The required mass of iron III oxide is 2.1 Kg
2) The empirical formula of aluminum oxide is [tex]Al_{2} O[/tex].
3) The mass of lithium chloride required is 27.7 g
4) The mass of carbon dioxide produced is 186.6 g
What is the stoichiometry?We have to note that we can only be able to obtain the parameters that has to do with an equation when we can be able to use the stoichiometry of the reaction and this depends on the equation of the reaction.
1) Number of moles of iron = 1.50 * 10^3 g/ 56 g/mol
= 26.8 moles
If 2 mole of iron III oxide produces 4 moles of iron
x moles of iron III oxide produces 26.8 moles of iron
x = 13.4 moles
Mass of the iron III oxide = 13.4 moles * 160 g/mol
= 2.1 Kg
2) Number of moles of Al = 2.91 g/27 g/mol
= 0.11 moles
Number of moles of oxygen = ( 5.50 - 2.91 )/32 g/mol
= 0.06 moles
Dividing through by the lowest ratio, the empirical formula is [tex]Al_{2} O[/tex].
3) Number of moles of lead II acetate = 106 g/325 g/mol
= 0.33 moles
If 1 mole of lead II acetate reacts with 2 moles of lithium chloride
0.33 moles would react with 0.33 * 2/1
= 0.66 moles of lithium chloride
Mass of the the lithium chloride = 0.66 moles * 42 g/mol
= 27.7 g
4) Number of moles of octane = 60.3 g/114 g/mol
= 0.53 moles
2 moles of octane produces 16 moles of carbon dioxide
0.53 moles of octane produces 0.53 * 16/2
= 4.24 moles
Mass of carbon dioxide = 4.24 moles * 44 g/mol
= 186.6 g/mol
Learn more about stoichiometry:https://brainly.com/question/9743981
#SPJ1
what would happen if you used equal masses of all the compounds? for example, 2.00 g as opposed to equal moles of each compound?
a. equal masses would produce different amounts of CO2
b. equal masses would produce the same amount of CO2
c. equal masses would show extreme variation and be difficult to measure in the lab
option c - equal masses would show extreme variation and be difficult to measure in the lab if you used equal masses of all the compounds.
Equal masses would imply a different number of moles. And reactions are molecular in nature. A reaction between 1 mole of A and 1 mole of B, for example, produces 1 mole of C. However, because their molar masses are likely to differ, we cannot apply the same mass formula and expect the same result. Consider the reaction HCl + NaOH, which produces NaCl + H2O. This reaction demonstrates that 1 mole of hydrochloric acid and 1 mole of NaOH produces 1 mole of NaCl and 1 mole of water. However, the reaction is very different in terms of mass because each of the reactants has a different molar mass.
learn more about molar mass here:
https://brainly.com/question/7585012
#SPJ4
What is the wavelength of electromagnetic radiation that has a Frequency of 5.65x 10¹11/s or hertz?
m
The wavelength of an electromagnetic radiation that has a frequency of 5.65 x 10¹¹ hertz is 5.31 × 10-⁴m.
How to calculate wavelength?Wavelength is the length of a single cycle of a wave, as measured by the distance between one peak or trough of a wave and the next.
Wavelength is often designated in physics as λ, and corresponds to the velocity of the wave divided by its frequency as follows:
λ = v/f
According to this question, a wave has a frequency of 5.65 × 10¹¹ Hertz, the wavelength can be calculated as follows:
λ = 3 × 10⁸m/s ÷ 5.65 × 10¹¹ Hertz
λ = 5.31 × 10-⁴m
Therefore, 5.31 × 10-⁴m is the wavelength of the wave.
Learn more about wavelength at: https://brainly.com/question/12924624
#SPJ1
the ksp can be used to find the concentration of hydroxide ions, and thus determine the ph given a concentration of of aluminum. at what ph will precipitation of al(oh)3 begin if 3.50 lb of aluminum sulfate, al2(so4)3 , is added to 1150 gallons of water (with a negligible change in volume)?
The concentration of hydroxide ions is 0.001145 M and, the ph given a concentration of aluminium is 3.9.
(Molar mass of 342.15 g/mol).
In order to answer this question, we must first convert our units. We are given 6.70 lb = 453.592 × 6.70 lb = 3039.0664 g of aluminium sulphate.
Water in 2050 gallons is equal to 2050 x 3.785 or 7759.25 litres.
Then, using the following formula, we will search for the Concentration of aluminium sulphate:
The formula for concentration is volume x moles.
Remember: 8.8823 moles is equal to 3039.0664 / 342.15 moles. 2050 gallons, or 7759.25 litres, make up the volume.
As a result, when we plug the values of the volume and number of moles into the previous equation (1), we get;
Concentration is equal to 8.8823 moles per 7759.25 litres, or 0.001145 M.
The solubility product equation, which is what we'll utilise next today, is as follows:
Ksp = (Al^3+) (OH^-)^3.
So, we have the ksp = 1.3 × 10^-33 and the value of (Al^3+)= 0.001145 M.
Hence, making (OH^-) the subject of the formula;
(OH^-) = ( 1.3 × 10^-33 / 0.001145)^1/3.
(OH^-) = 8 × 10^-11 M.
Hence, pOH = - log (OH^-)
pOH = - log (8 × 10^-11).
pOH = 10.1
Therefore, the value of pH is; 1
pH + pOH = 14.
pH = 14 - 10.1 = 3.9.
Learn more about Ksp here:
brainly.com/question/4637627
#SPJ4
10) molar solubility of calcium fluoride 1 attempt 0/1 points find the molar solubility of calcium fluoride in a solution containing 0.49 m ca(no3)2(aq)ca(no3)2(aq). a. solubility mol/l evaluate
In a solution of 0.49 M Ca(NO3)2, the molar solubility of calcium fluoride is 0.86X10-5
The solubility product constant, abbreviated Ksp, can be used to calculate the equilibrium concentration of ions when a salt dissolves in a solvent. Literature can be used to determine the Ksp value of salts that are often consumed at 25°C.
Ca(NO3)2 -> Ca2+(aq) + 2(NO3)-1
CaF2(s) -> Ca2+(aq) + 2 F-(aq)
I 0.49 0
C x 2x
E 0.49+X 2x
We know the Ksp of Ca2+ is 1.46x10-10
solubility ksp = [Ca2+][F-]2
ksp = (0.49+x) *(2x)^2
1.46x10-10= (0.49) * 4x^2
x= √(0.756*10-10) = 0.86x10-5
Hence the molar solubility of calcium fluoride in a solution containing 0.49M Ca(NO3)2. is 0.86x10-5M
To learn more about solubility click here https://brainly.com/question/28170449
#SPJ4
a certain liquid x has a normal freezing point of -9.30 and a freezing point depression constant . calculate the freezing point of a solution made of of iron(iii) chloride
The supplied statement states that the supplied solution's freezing point is -12.1 °C.
What in chemistry is a solution?In chemistry, a solution is a homogeneous combination of two or more compounds in their relative proportions, which may be constantly changed up to what is known as the limit to solubility. Although solutions of vapors and particles are possible, the term "solution" is most frequently used to refer to the liquid condition of matter.
Briefing:FeCl₃ is dissolved, and X (the solvent) is a liquid.
Freezing point of X [tex]\left(T_f^0\right)[/tex] = -4.50°C
Depression constant ([tex]K_{f}[/tex]) = 1.82°C kg/mol
Weight of FeCl₃ = 0.11 kg = 0.11 * 10³g
Weight of X = 650 g = 650 * 10⁻³ kg
Freezing point of solution ([tex]T_{f}[/tex]) = ? ( In °C )
Therefore, we first determine the molality, and then we determine the freezing point of the solution using the depression in freezing idea.
As FeCl₃ dissociates in liquid.
Fe³⁺ + 3Cl⁻ → i.e. total 4 ions
So, vary Hoff factor for FeCl₃ = 4
We know,
Molar mass of FeCl₃ = 162.2g/mol
Calculation:
Molarity of solution (m) = moles of solute/amount of solvent
= Mass of FeCl₃/Molar mass of FeCl₃ * 1/ Mass of X
= 0.11 * 10³/162.2 * 1/ 650 * 10⁻³
= 1.0433 moles/kg
Now from depression for freezing point concept,
We have,
Δ[tex]T_{f}[/tex] = i * [tex]K_{f}[/tex] * m
[tex]T_f^0[/tex] - [tex]T_{f}[/tex] = i * [tex]K_{f}[/tex] * m
[tex]T_{f}[/tex] = [tex]T_f^0[/tex] - i * [tex]K_{f}[/tex] * m
= -4.50 - 4 * 1.82°C * 1.0433
[tex]T_{f}[/tex] = -12.1°C ( Freezing point of solution ).
To know more about Solution visit:
https://brainly.com/question/7932885
#SPJ4
if a grating with more lines per unit length were used, how would the observed angles or spread of the spectra be affected?
Grating with more lines per unit length is given by, (a + b) sin (theta n)=n ( lambda), where, a + b is grating element, the distance between two consecutive slits, n is order of principal maxima and Lambda is wavelength of light.
Consider the first order maximum on either side of central maximum. For first order n=1. Therefore ,
sin(theta 1)=(lambda)/(a + b).
If we increase the number of lines of grating, correspondingly the grating element (a + b) decreases , hence diffraction angle becomes large for given wavelength . But, then there is limit on number of lines, because sin(theta) should not become greater than 1. However, within reasonable limit on number we can get better resolution that is more angular separation of spectral lines by increasing lines of the plane diffraction grating.
To learn more about Diffraction Grating please visit:
https://brainly.com/question/13902808
#SPJ4
the water of the dead sea is extremely salty, which gives it a very high density of 1240 kg/m3.
A person floats much higher in the Dead Sea than in ordinary water because salt water has a higher density than fresh water. Saline water has a density of (1080 kg m per cube) while fresh water has a density of ( 1000 kg m per cube). Because of this, swimming in salt water is simpler for swimmers.
Facts About the Dead SeaCompared to the 3.5% salinity of the Mediterranean, the Dead Sea has a salinity of 34.2%. It ranks behind the Don Juan Pond and Lake Vanda in Antarctica, the Lake Assal in Djibouti, and Lake Vanda as the fourth saltiest body of water in the world. The Dead Sea doesn't pour out, which is one of the causes of excessive salinity.
The dead sea has a concentration of 34% and a very high salt content.The water is thicker than normal fresh water because of the high quantity of dissolved salts in it.Our body weight provides more buoyancy or buoyant force because it is lighter than the water's density.We float on the dead sea as a result.To learn more about the Dead sea here:
https://brainly.com/question/12913257#
#SPJ4
Complete Question
The water of the Dead Sea is extremely salty. which gives it a very high density of 1240 kg/m^3. Explain why a person floats much higher in the Dead Sea than in ordinary water.
Which would you expect to be a conductor of electricity in the solid state? O iodine (12) O silver spoon (Ag) O lime (CaO)
Silver spoon (Ag) is a conductor of electricity in the solid state.
What is electrical conductors?Since a conductor presents little to no resistance to the passage of electrons, which results in an electrical current, a conductor carries electricity. Generally speaking, excellent electrical conductors include metals, metal alloys, electrolytes, and even some nonmetals, such as graphite and liquids, including water.An item or category of material that permits the movement of charge in one or more directions is referred to as a conductor in physics and electrical engineering. Metals are frequently used as electrical conductors in materials.Common electrical conductors include copper, silver, aluminium, gold, steel, and brass. Silver, copper, and gold are the metals with the highest conductivity.Learn more about electrical conductors refer to :
https://brainly.com/question/492289
#SPJ4
which diol is produced by treatment of trans-2-butene with osmium tetroxide followed by workup with aqueous sodium bisulfite?
The (2R,3R)-(-)-2,3-Butanediol is the diol is produced by treatment of trans-2-butene with osmium tetroxide followed by workup with aqueous sodium bisulfite.
It is used as a chiral auxiliary, chiral ligand and constructing block. Cyclocondenses with ketones for (13)C NMR willpower of optical purity. It is used withinside the decision of carbonyl compounds in fueloline chromatography. Fully miscible in water (2R,3R)-2,3-butanediol.
Alkene oxidation with OsO4 accompanied through sodium bisulfite paintings up consequences withinside the syn addition of hydroxyl corporations. For trans-2-butene, the 2 hydroxyl corporations may want to similarly upload at the pinnacle face or backside face.
Read more about aqueous;
https://brainly.com/question/19587902
#SPJ4