Suppose you make a new kind of compact disk that is the same thickness as a current disk but twice the diameter. By what factor will the rotational inertia increase? Idisk= 1/2MR^2 8 2 16

When the overcurrent protection for a conductor is located on the load end rather than the supply side of a conductor it is considered to be a tap conductor.

The National Electrical Code (NEC), the benchmark for safe electrical design, installation, and inspection to protect people and property from electrical hazards, defines a tap conductor as a conductor, other than a service conductor, that has overcurrent protection rated more than the ampacity of a conductor. A tap conductor has overcurrent protection ahead of its point of supply that exceeds the value permitted for similar conductors that are protected as described in NEC 240.4. Hence, when the overcurrent protection for a conductor is located on the load end rather than the supply side of a conductor it is considered to be a tap conductor.

Learn more about Tap conductor:

https://brainly.com/question/14744748

#SPJ4

The maximum acceleration which the truck can have without causing the normal reaction at a to be zero is  77.3 ft/sec²

Calculation :

Sum of vertical forces,

By - W = (W/g) ay

By - 180 = (180/32.2) x 0

Vertical reaction, By = 180 lb

Horizontal forces,

Bx = m ax

Bx = (W/g) ax = (180/32.2) x 7.3

Horizontal reaction, Bx = 432 lb

Now taking moment about B,

W x 10 x (12/13) = m ax x 10 x (5/13)

180 x 10 x 12/13 = (180 /32.2) ax x 10 x 5/13

Acceleration, the rate of change of velocity over time for both velocity and direction. A point or object moving in a straight line accelerates as it accelerates or decelerates. Circumferential motion is accelerated because it always changes direction even at constant velocity.

Acceleration, ax = 77.3 ft/sec^2

Learn more about Acceleration here : https://brainly.com/question/460763

#SPJ4

a) The amplitude of oscillation is 0.780 m.

b) The force constant of the spring can be determined by using the equation F=kx, where F is the force applied to the mass, k is the force constant, and x is the displacement of the mass. Since the displacement of the mass is 0.780 m, we can solve for k to get k = F/x = 0.780 N/m.

c) The position of the mass after one half a period is given by x(t) = (0.780 m)cos[(18.0 rad/s)t] = (0.780 m)cos[(9.0 rad/s)t] = 0.780 m.

d) The position of the mass one-third of a period after it has been released is given by x(t) = (0.780 m)cos[(18.0 rad/s)t] = (0.780 m)cos[(6.0 rad/s)t] = -0.500 m.

e) To determine the time it takes the mass to get to the position x=-0.500 m after it has been released, we can use the equation x(t) = (0.780 m)cos[(18.0 rad/s)t]. Since we know that x=-0.500 m when t=t0, we can solve for t0 to get t0=6.00 s. Therefore, it takes the mass 6.00 s to get to the position x=-0.500 m after it has been released.

For more questions like Oscillation click the link below:

https://brainly.com/question/13981801

#SPJ4

The rank of particles on the basis of energy is  2 > 3 = 4 > 1 > 5 = 6

The Rank of particles on the basis of speed is 1=2=3=4=5=6

All speed that is faster than light is the same. When a charged particle and an antiparticle annihilate one another, energy can create both positive and negative charges, +q and q. If both +q and q are 0, it follows that m must also be 0.

When, in order to conserve energy, an electron and positron annihilate to produce two genuine photons with mass zero that depart with the same energy as the electron-positron pair.

Additionally, contrary charges and timings must cancel. As opposed to the positron, which travels time backward, the electron pushes time forward. Time cancels out, as a result, creating two photons that travel at the speed of light while maintaining the illusion of time standing still.

Nuclear weapons have been theorized to be triggered by antimatter, and thermonuclear energy may be produced with it.

Learn more about Quantum Physics here

https://brainly.com/question/26095165

#SPJ4

82 K is the change in temperature of the gas during this expansion.

Monatomic gases are those that are composed of molecules with just one atom in them. Monatomic gases include gases like helium or sodium vapor. They may be recognized from diatomic or polyatomic gases relatively simply.

A single atom makes up a monoatomic gas. Examples include the gases helium and neon. Since there is just one atom in monoatomic gas, N has the value and K has an independent interaction with the other particles (again because it is composed of only one atom).

Given that,

no. of moles (n) = 8.8 moles

work (W) = 9000 J

For adiabatic process, Q = 0

=> ΔU = - W

For ideal mono-atomic gas, ΔU = 3nRΔT/2

So, ΔT = -2W/3nR

or, ΔT = - (2 × 9000) / (3 × 8.8 × 8.314)

or, ΔT = - 82 K

So, 82 K is the change in temperature of the gas during this expansion.

To know more about temperature refer to:

https://brainly.com/question/25677592

#SPJ1

V(x, Y, Z) = 16Vo/pi2 is the potential inside the pipe. (-pi(m/a)2 + (n/b)2)1/2) sin (m*piy/a)sin (n*pi*Z/b). Because only one end of a rectangular metal pipe with sides a and b is grounded at x = 0.

Simply said, potential difference is the difference in electrical potential between two places. Two positive charges will repel one another when presented close to one another. The standard addresses the sizing and dimensioning of steel pipes. These pipes come in seamless and welded varieties, and they can withstand high or low temperatures and pressures. The pipe is distinct from the tube (Pipe versus Tube) in this context because it is specifically used for pipeline systems and the transmission of fluids (oil and gas, water, slurry).

In the event that Vo(y, z) = Vo Vo(a)(1-(-1)m-1 * b/n*pi(1-(-1)n) = Cn,m(a/2, b/2) V(x, y, z) = 16Vo/pi2(-pi(m/a)2+(n/b)2)1/2) sin (m*piy/a)sin(n*p)

Learn more about potential here

https://brainly.com/question/12198573

#SPJ4

The complete question  is -

An infinitely long rectangular metal pipe (sides a and b) is grounded, but one end, at x = 0, is maintained at a specified potential Vo(y, z), Find the potential inside the pipe. as indicated in Fig. y V=0 Vo(y, 2) b

The answer to the question is that the acceleration equals 4.9 m/s² and the cord tension is 58.8 N.

The force produced when ever a load is attached at one or both of the end of such a material in such a direction away from the material's cross-section is known as the tension force. It's frequently referred to a tension force as a "pushing" force.

(a) Let's use Newton's Second Law for Movement to our example:

[tex]$$\begin{gathered}T-m_1 g=m_1 a, \\T-m_2 g=-m_2 a .\end{gathered}$$[/tex]

Eliminating [tex]$T$[/tex], we get:

[tex]$$\begin{gathered}\left(m_2-m_1\right) g=\left(m_1+m_2\right) a, \\a=\frac{\left(m_2-m_1\right) g}{m_1+m_2}, \\a=\frac{(12 \mathrm{~kg}-4 \mathrm{~kg}) \cdot 9.8 \frac{\mathrm{m}}{\mathrm{s}^2}}{4 \mathrm{~kg}+12 \mathrm{~kg}}=4.9 \frac{\mathrm{m}}{\mathrm{s}^2} .\end{gathered}$$[/tex]

(b) By adding "a" to the first equation, we can get the cord's tension:

[tex]$$T=m_1(a+g)=4 \mathrm{~kg} \cdot\left(4.9 \frac{\mathrm{m}}{\mathrm{s}^2}+9.8 \frac{\mathrm{m}}{\mathrm{s}^2}\right)=58.8 \mathrm{~N}$$[/tex]

To know more about Tension visit:

https://brainly.com/question/11348644

#SPJ1

Brutus grabs Fred in a tight grip, and they fall to the ground.

The distance they slide is 0.0915m.

As given in the question

The mass of Fred ([tex]M_1[/tex]) is 65 kg

The mass of Brutus ([tex]M_2[/tex]) is 130kg

Speed of Fred running with foot ball ([tex]V_1[/tex]) is  -5.8m/s ( negative direction)

Speed of Brutus ([tex]V_2[/tex]) is 4m/s

The coefficient of friction is given as 0.30

By applying the law of conservation of momentum is

[tex]M_2V_2 - M_1V_1=(M_1+M_2)V[/tex]

[tex]M_1[/tex] is the mass of first object

[tex]M_2[/tex] is the mass of second object

[tex]V_1[/tex] is the velocity of first object

[tex]V_2[/tex] is the velocity of the second object

V is the velocity after colliding

Now

130 x 4 - 65 x 5.8= ( 65 + 130) V

520 - 377 = 195V

195V =143

V = 0.733m/s

Now acceleration due to friction is

=> [tex]\mu_k\ g[/tex]

=> 0.3 x 9.8

=.>2.94m/[tex]s^2[/tex]

To find the distance

[tex]v^2-u^2=2as[/tex]                             ( where u = 0)

=> [tex](0.733)^2=2 \times 2.94 \ s[/tex]

=>  s = 0.0915m

To know more about law of conservation of momentum:

https://brainly.com/question/29244885

#SPJ4

At touchdown, the flaps' lift coefficient reaches its maximum of 1.8. Upon touchdown, there is a 279-meter zero lift drag.

Vt = 1.8 Vtotal = 1.8 [tex]\sqrt{2w/PSc}[/tex]

Pg = 1.225 kg/m³

1.8 [tex]\sqrt{2* 105000/1.225*50*3}[/tex] = 61.02

V = 0,7 Vt = 0.7 *61.02 = 42.714

After touch down L = 0,

Drag = 1/2 *1.225 *30 *30 *50*0.05 = 1448

Sl = 1.69 * 105000² / 9.81 * 61.02*50*3[1448 + 0.02*105000]

Sl = 279m

The zero-lift drag coefficient and the lift-induced drag coefficient factor, respectively, are denoted by CD0 and k. Under a particular aircraft aerodynamic configuration, the values of both parameters are taken to be constants. Flight can be accomplished without drag. However, without removing air, it is impossible to completely eliminate drag during flight. Although it is not entirely necessary for flight, an airplane that achieves lift will always experience some form of drag because air is required to produce lift. Increasing the zero-lift drag coefficient Cd0 has the effect of raising (TR)min while lowering the velocity at which it occurs. When the drag-due-to-lift factor K is raised, the result is an increase in (TR)min and an increase in the velocity at.

Learn more about Zero lift drag here:

https://brainly.com/question/14529452

#SPJ4

Answer:

A: It becomes bigger.

Explanation:

When the ball is moved closer to the light source, the size of its shadow on the wall will increase. This is because the light from the bulb will be more concentrated on the ball, resulting in a larger area of the wall being blocked from the light and therefore appearing as part of the shadow. The darkness of the shadow will not change, as the amount of light being blocked by the ball remains the same. The sharpness of the shadow may also not change, as the distance between the ball and the wall will not affect the clarity of the shadow's edges. However, the length of the shadow may appear shorter, as the ball will be closer to the wall and therefore the shadow will appear to be cast over a shorter distance.

(please mark as brainliest!)

The current flowing through the circuit A is IA = 2ε/(R1 + R2)

b) IB = 2ε/(2R2 + R1) c) P = 0.064

The equivalent resistance of the circuit A in series is calculated as follows;

Re = r1 + r2

The emf of the battery connected to circuit A

emf = e

The current flowing through the circuit A is calculated as follows;

I = V / R

I = e / r1 +  r2

Total resitance in circuit A = Req = R1+R1+R2 =2R1 + R2

total emf in circuit A = 2E

I = 2E/Req

I = 2E/(2R1+R2)

given : E = 10 V

R1 = 300 ohm

R2 = 5000 ohm

since connection is in series so current remain same across resistors

I = 2*10/(2*300 + 500)

I = 3.57 x 10^-3 A

power dissipated by R2

P = I^2*R2

P = (3.57 x 10^-3)^2 * 5000

P = 0.064

Learn more about circuit here:

https://brainly.com/question/12608516

#SPJ4

Option B;A coin and a ring roll down an incline starting at the same time. The coin will be the one to descend first.

Its rotational inertia will be higher. Because of this, it accelerates more slowly than a coin. First to the bottom, the coin makes it. Any item that can be turned possesses rotational inertia. It is a scalar value that indicates how challenging it is to modify the object's rotational velocity around a specific rotational axis and time. Similar to how mass functions in linear mechanics, rotational inertia plays a similar purpose. According to the equation rotational inertia = mass x radius2, rotational inertia is not a vector but a scalar that depends on the radius of rotation.

Learn more about time here:

https://brainly.com/question/862972

#SPJ4

In order to find the actual distance of the shark from the wall, we need to use the lens equation. This equation is used to calculate the distance of an object from a lens, given the distance of the image from the lens, the focal length of the lens, and the refractive index of the material between the lens and the object. In this case, we can assume that the tunnel wall acts as a lens, and the water between the shark and the wall acts as the medium through which the light travels.

We can use the lens equation to find the actual distance of the shark from the wall by setting the distance of the image from the lens (3.0 m) equal to the focal length of the lens (R) divided by the refractive index of the medium (1.33), minus the actual distance of the shark from the wall (d):

3.0 m = (4.0 m)/1.33 - d

Solving for d, we find that the actual distance of the shark from the wall is 1.5 m. Therefore, the shark is actually 1.5 m away from the tunnel wall, not 3.0 m as it appears in the tunnel.

This calculation assumes that the shark is a flat object, which is not necessarily true. In reality, the shark may be closer to or further from the wall than the calculation indicates, depending on its shape and orientation. Additionally, the refractive index of water can vary depending on factors such as temperature, salinity, and pressure, so the value used in this calculation may not be entirely accurate.

The shark 's actual distance from the wall is 4 m.

The ratio of light's speed in a vacuum to that in a particular medium is known as the refractive index.

Refraction index and index of refraction are other names for the term "refractive index." The characteristics of the medium affect the speed of light in that medium. The optical density of the medium affects the speed of electromagnetic waves.

When the object is in denser medium and  observer is in rarer medium; refractive index of the medium can be written as:

μ = actual distance/apparent distance

actual distance = μ × apparent distance

= 1.33 × 3.0 m

= 3.99 m

= 4 m. (approx.)

Learn more about refractive index  here:

https://brainly.com/question/23750645

#SPJ2

When air enters the diffuser of a ramjet engine decelerates to negligible velocity then nozzel exit velocity is 1320.725 m/s.

A nozzle (from nose, meaning 'small spout') is a tube of varying cross-sectional area (usually axisymmetric) aiming at increasing the speed of an outflow, and controlling its direction and shape. Nozzle flow always generates forces associated to the change in flow momentum.

In the simplest case of a rocket nozzle, relative motion is created by ejecting mass from a chamber backwards through the nozzle, with the reaction forces acting mainly on the opposite chamber wall, with a small contribution from nozzle walls.

The flow in a nozzle is very rapid (and thus adiabatic to a first approximation), and with very little frictional loses (because the flow is nearly one-dimensional, with a favourable pressure gradient except if shock waves form, and nozzles are relatively short), so that the isentropic model all along the nozzle is good enough for preliminary design.

Applying steady flow energy equation,

h1+v1^2/2000 = h2+v2^2/2000

680.556^2/2000 = Cp(T2-T1)

230.42 = T2-T1

T2=460.425 K

and P2=227 Kpa

h2+q=h3

q=Cp(T3-T2)

T3=1734.05K

Now by sfee equation

V4=1320.725 m/s

To know more about nozzel here

https://brainly.com/question/16898265

#SPJ4

For coexisting states of matter, this measurement is utilized in its orthobaric form. Comparing these ratios is specific gravity. This idea is used by buoyancy to determine whether an object will float or sink.

1 gram per cubic centimeter is the unit of measurement for water. This number, which is equal to mass over volume, is known as density, and it is represented by the Greek letter rho. A hydrometer or aerometer measures a fluid's specific gravity, or relative density, which is the difference between the density of the fluid and the density of water. The typical components of a hydrometer are a cylindrical stem made of glass, a bulb weighed down with lead or mercury so that it can float, and a water-filled container.

To learn more about buoyancy click here https://brainly.com/question/19168433

#SPJ4

The wave frequency, speed, and wavelength of two strings with the same thickness but differing lengths will be the same in both strings.

A string will vibrate at a varied frequency depending on its length. Higher frequency and higher pitch are produced by shorter strings. The  frequency and wavelength are inversely proportional. Shorter frequency corresponds to a longer wavelength. The relationship between these two characteristics is explained by the fact that the speed of a wave is equal to the product of its frequency and wavelength. A wave's speed increases with increased string tension, which raises its frequency (for a given length). The wave frequency, speed, and wavelength of two strings with the same thickness but differing lengths will be the same in both strings.

To learn more about wavelength click here https://brainly.com/question/1292129

#SPJ4

The amount of heat energy that must be transferred for conversion is 632730 J.

Mass of ice = m = 210 g

Temperature change = t = 100 - 0 = 100

Latent heat of fusion = L = 334 KJ/ Kg

Latent heat of vaporisation = L' = 2.26 X 10³ KJ/Kg

Specific heat of water = c = 4.19 KJ/Kg

Heat required to convert ice to water = mL

Heat required to raise the temperature of water to boiling point = m X c X t

Heat required to convert water to steam = mL'

Thus, total heat energy required = q =

= q = mL + mL' + (m X c X t)

= q = (210 X 334) + (210 X 2.26 X 10³) + (210 X 4.19 X 100)

= q = 70140 X 474600 + 87990

= q = 632730 J

To know more about Heat Energy Transfer:

https://brainly.com/question/20386211

#SPJ4

The tension in the cable is F = πEaV²r³/2d²

The work. done. by the cable. is W = πEaV²r²/4d

[tex]\mathbf{U_i-U_f=\frac{\varepsilon_0\pi r^2 V^2}{2d}-\frac{\varepsilon_0\pi r^2 V^2}{4d}}\mathbf{\Rightarrow U_i-U_f=\frac{\varepsilon_0\pi r^2 V^2}{4d}}[/tex]

The equation can be used to depict the electric field created between two circular plates of a capacitor if they are separated by a constant distance and supported by a cable.

E = V/d

E' = E/2

F = qv/2d

F = Eav2r2/2d2.

Assuming that dz has shifted the upper plate higher, we can express the tension's work as follows:

dw = T*dz

dz = F * dw

The cable's work is W = Eav2r2/4d, or W = Eav2r2/2z2*dz.

Before the top plate is raised, the electrical energy capacitor has the following amount of energy stored in it:

Ui = 1/2 Cv²

Ui = EaR2V2D

Yes, the work carried out by the cable is equivalent to the change in electrical energy that has been stored. The variation in energy previously stored

Ui = Eaπr²v²/4d

[tex]\mathbf{U_i-U_f=\frac{\varepsilon_0\pi r^2 V^2}{2d}-\frac{\varepsilon_0\pi r^2 V^2}{4d}}\mathbf{\Rightarrow U_i-U_f=\frac{\varepsilon_0\pi r^2 V^2}{4d}}[/tex]

Learn more about tension here:

https://brainly.com/question/15211735

#SPJ4

Answer:

Ellipses are required in engineering, architectural, and machine drawings for two main reasons. First, any circle viewed at an angle will appear to be an ellipse. Second, ellipses were common architectural elements, often used in ceilings, staircases, and windows.

The ellipse is one of the four classic conic sections created by slicing a cone with a plane. The others are the parabola, the circle, and the hyperbola. The ellipse is vitally important in astronomy as celestial objects in periodic orbits around other celestial objects all trace out ellipses.

When the current in the circuit is double of its initial value and separation is half then the original capacitive reactance in terms of r is 3r.

Capacitive Reactance is the relationship between reactance, frequency and capacitance. Resistance is unaffected by the rate of change of voltage or current and remains the same whether DC, or AC of any frequency is applied.

In a purely resistive circuit Ohms law applies and V= IR. Calculations of resistance in AC circuits are the same as for DC. The only extra thing to remember when calculating AC values, is that the same type of value, e.g. the RMS, Average value, or the peak-to-peak value must be used for all AC voltages or currents throughout the equation.

Inductance and capacitance however, have an effect on current that depends on frequency, and when either component is used with AC voltages and currents, then the frequency of the waveform must be taken into account.

To know more about capacitive reactance here

https://brainly.com/question/27853857

#SPJ4

We may calculate the proportion of data values that are 1.5 standard deviations or more from the mean using Chebyshev's rule in statistics. Alternately, we can calculate the proportion of data values that deviate by 2.5 standard deviations from the mean.

What does a 75% Chebyshev interval mean?

Therefore, Chebyshev's Theorem informs you that at least 75% of the values lie within the range of 100 20, or 80 to 120. In contrast, no more than 25% of cases fall outside of that range. 1.41 standard deviations is an intriguing range.

What does the Chebyshev inequality tell us?

According to Chebyshev's inequality, 75% of values are found within two standard deviations of the mean, and 88.9% are found within three standard deviations of the mean. It is true for.

To know more about chebyshev to estimate visit;

https://brainly.com/question/14019579

#SPJ4

The tension of the left rope is 98N and tension of the right rope is 29.4N if two boxes are connected by a rope passing over a pulley .

We know very well when two masses are attached by a pulley,the only force acting on the blocks is the force due to gravity. Tension is measured in newtons. Also, since different masses are attached on both ends of pulley due to that tension generated in the rope are different.

We know force due to gravity is equal to =mg where m is defined as the mass and g is defined as the acceleration due to gravity.

Now, mass of left block is =10kg.Therefore,tension in left rope=mg

=>Tension in left rope=10×9.8

=>Tension in left rope=98N

Similarly, mass of right block is =3kg.Therefore,tension in right rope=mg

=>Tension in right rope=3×9.8

=>Tension in right rope=·29.4N

Hence, required tensions are 98N and 29.4N

To know more about tensions, visit here:

https://brainly.com/question/15880959

#SPJ4

A 0.53kg mass is hung on a vertical spring which has spring constant k=70N/m, balanced then the spring stretch relative to its original length as a result of the mass hanging on it is 0.742m

Given that the mass of block (m) = 0.53kg

spring constant of the spring (k) = 70N/m

The force exerted by the spring balances the weight of the hanging mass is (F) = kl where l is length of the spring

We know that F = mg

mg = kl

then 0.53 x 9.8 = 70 x l

l = 0.0742m

Hence the length of the spring is 0.742m

To learn more about force click here https://brainly.com/question/13191643

#SPJ4

if all volcanic activity were to stop tomorrow, there would be a reduction in carbon flux into the atmosphere. is 99%

A carbon flux is the volume of carbon that is transferred across carbon stocks during a certain period of time. 1. To put it simply, it is the transfer of carbon from the land to the seas, the atmosphere, and living things. For instance, the atmosphere receives inflows from decomposition (CO2 emitted by the breakdown of organic matter), forest fires, and the burning of fossil fuels, while the atmosphere also receives outflows from plant growth and ocean absorption. The ocean operates as a net sink of 1.7 GtCyr, which is where the highest natural flow occurs between the atmosphere and the ocean. A significantly smaller net sink exists in the terrestrial ecosystem.

Learn more about carbon flux here:

https://brainly.com/question/10111081

#SPJ4

The electron transport chain uses electrons between protein complexes to set up a proton gradient.

As the name suggests, the electron transport chain involves a series of proteins that pass electrons from one to the next. These electrons are removed from glucose, releasing energy as they pass through the electron transport chain. This energy is used to pump protons across the semipermeable membrane, creating a proton gradient that can drive ATP synthesis.

The electron transport chain is a series of four protein complexes that combine redox reactions to generate an electrochemical gradient that leads to the formation of ATP in a complete system called oxidative phosphorylation.

When an electron moves from a low redox potential to a high redox potential, the free energy released when high-energy electron donors and acceptors are converted to low-energy products is used by complex electron transport chains to create an electrochemical ion gradient. It is this electrochemical gradient that drives ATP synthesis by coupling to oxidative phosphorylation by use of ATP synthase.

Read more about cell physiology at:

brainly.com/question/14228763

#SPJ4

Volume of water is  17.2N,

The rock displace volume of water whose weight is 37.6 - 20.4 = 17.2N

The mass of this water is 17.2/9.80 =1.755 kg and its volume equal to the rock volume is 1.755/1000 =  1.755 × [tex]10^{-3}[/tex]

The form of the container where the water is contained affects the amount of water inside. You must know the vessel's length, width, and depth in order to calculate the volume of a square or rectangular vessel. The volume equation is V=L W D, where L stands for length, W for width, and D for depth. The formula for the rectangular tank's filled volume is provided as V(fill) = l b f, where "l" denotes the tank's length, "b" denotes its width, "f" denotes its level of water fill, and "V(fill)" is the filled volume of the tank.

Learn more about Volume here:

https://brainly.com/question/17322215

#SPJ4

When  two lamps with one thick filament and one with a thin filament of the same material, are connected in parallel to a power supply. Then the  current is greater in the lamp with a thick filament.

Ohm's Law can be used to calculate the relationship between voltage, current, and resistance in an electrical circuit.

Ohm's law can be written as follows:,

V = I x R

When written out, the formula is as follows: voltage = current x resistance, or

Volt = Amp x Ω.

Because theory is connected in parallel and the potential difference across each filament is the same, we can conclude that a material's resistance is [tex]R = \rho*lA[/tex]

[tex]\rho[/tex] is the resistivity if the material for the two filaments is the same and the length 'l' is also the same

The area of cross section of a thick filament is greater than that of a thin filament. The resistance is less than the thin filament current. [tex]I = \frac{V}{R}[/tex]

since V is same

If R is smaller, current is greater, and thus current is greater in thick filament.

To learn more about ohm's law refer here

https://brainly.com/question/14796314

#SPJ4

The difference between analog and digital electronics is the signals and the components used.

The electronics can be classified into categories: analog and digital electronics. Some differences between both of them are as follows :

Thus, two differences between analog and digital electronics are analog uses continuous signals while digital uses discrete signals. Then, the analog uses passive components whereas digital uses active components.

Learn more about analog and digital by clicking this link :

https://brainly.com/question/23777902

#SPJ4

Difference between analog and digital electronics:

Analog electronics are electronics that deal with continuous signals. They generally provide a better and more accurate representation of changes in physical phenomena, such as position, pressure, and light.

Digital electronics are electronics that deal with binary signals. The digital signals for this type of electronics are represented using binary language (0's and 1's). Their circuits are usually composed of large assemblies of logic gates.

The difference between the two are the components used and the type of signal they deal with.

Learn more about digital technology at https://brainly.com/question/4371054

#SPJ4

According to the given hint, solar panels generate an average  about 200 Watt/m2.

1. The annual USA energy consumption is 103,108,904,000,000,000,000J.

2. The average power required for the USA over one year is 3.2 trillion watt.

3. The total area needed to provide this power is 32.6 billion [tex]m^{2}[/tex].

4. The surface area of the USA is 9.834*[tex]10^{12}[/tex] [tex]m^{2}[/tex].

Solar energy originates from the sun. Solar panels (also called "PV panels") are used to convert light from the sun, which consists of energetic particles called "photons", into electricity that can be used to power electrical loads increase.

Solar panels can be used in a variety of applications including remote power systems for cabins, telecommunications equipment, remote sensing and, of course, power generation for residential and commercial photovoltaic systems.

Learn more about Solar panels here :-

https://brainly.com/question/28996669

#SPJ4

The measurement is 15.21 meters. When the jumper is at its maximum elongation, the cord will be extended by 85.21 m.

In light of this,

h=100 m bridge height

30 meters in length

40 N/m spring constant

Weight = 80 kg Assume we need to determine the distance at which the cord reaches its maximum elongation.

We must compute the distance.

We must compute the gravitational potential energy.

Using the gravitational potential energy formula

We must compute the value of x.

When the jumper is at its maximum elongation, the cord will be extended by 85.21 m. We must compute the distance. The negative symbol indicates the depth of the water.

As a result, the distance is 15.21 m.

Learn more about gravitational here-

https://brainly.com/question/3009841

#SPJ4