The range of accommodation is around 4 diopters at a near point of 25 cm. The range of accommodation is the eye's capacity to change its focus and perceive objects clearly at various distances. The distance between the close and far points is what determines it.
The far point is the furthest distance an item may be seen by the eye without accommodation. As the eye doesn't have to make any adjustments for things at a considerable distance, the distant point is typically thought of as being at infinity.
Finding the reciprocals of the near point distance and the far point distance, and then taking the difference between the two, will allow us to determine the range of accommodation.
If the far point is at infinity and the near point is at a distance of 25 cm (0.25 meters), the computation is as follows:
The accommodation range is equal to one divided by the difference between the two points.
We may ignore the reciprocal of the far point distance in this situation since 1 / infinity is getting close to zero.
Accommodations within a 1.25-meter radius
4 diopters' worth of accommodation range
As a result, the range of accommodation is around 4 diopters at a near point of 25 cm.
To know more about the accommodation range:
https://brainly.com/question/14397537
#SPJ12
the temperature at which water boils in la paz bolivia is 88 °c. convert this temperature in fahrenheit.
The temperature at which water boils in La Paz, Bolivia is approximately 190.4 °F.
The temperature at which water boils in La Paz, Bolivia is 88 °C. To convert this temperature to Fahrenheit, we can use the formula:
°F = (°C x 1.8) + 32
So,
°F = (88 x 1.8) + 32
°F = 190.4
To learn more about Celsius to Fahrenheit : https://brainly.com/question/26351021
#SPJ11
Imagine your life on Jupiter. Name some ways that your life might be different due to the increased gravity
If I lived on Jupiter, higher gravity would have a profound impact on my life in several ways. Here are some of those examples:
Movement
My movement would be significantly slower and more difficult due to Jupiter's enormous gravitational pull. Walking or standing would require more effort than on Earth because Jupiter's gravity is about 2.5 times stronger.
Physical Characteristics
Due to the greater gravity, my body would compress, making me look shorter and fatter than I would be on Earth. In addition, the pressure on my body would be significantly greater, perhaps leading to health problems such as circulation problems and joint pain.
Energy Consumption
As everything on Jupiter would require more energy to move, daily tasks such as cooking and cleaning would be more difficult and time-consuming.
Transportation
Due to Jupiter's tremendous gravity, alternative modes of transportation would be needed. To sustain the pressure, flying vehicles or spacecraft would have to be much stronger, and even then, they would move much slower than on Earth.
Sports and physical activity
Sports and exercise on Jupiter would be more difficult and potentially harmful due to the increased gravity. Running or jumping, for example, would put a lot of strain on the body and could lead to injury.
In short, due to the increased gravity, living on Jupiter would be drastically different from life on Earth, affecting everything from daily tasks to physical appearance and health.
Learn more about Jupiter and gravity,
https://brainly.com/question/4092256
An AC voltage is given by v(t) = 10 sin(1000nt +30º). a. Use a cosine function to express v(t). b. Find the angular frequency, the frequency in hertz, the phase angle, the period and the rms voltage value. c. Find the time-average power that this voltage delivers to a 25 n resistance.
a. The cosine function of v(t) is v(t) = 10 cos(1000nt - 60º). b. The angular frequency is 1000n radians per second. c. The time-average power is given by P = (Vrms)^2 / R, where R is the resistance. Substituting the given value of R = 25n, we get P = (7.07)^2 / 25n = 1.99 mW (milliwatts).
a. To express v(t) as a cosine function, we can use the identity sin(x + 90º) = cos(x). Therefore, v(t) = 10 sin(1000nt + 30º) can be rewritten as v(t) = 10 cos(1000nt + 30º - 90º) or v(t) = 10 cos(1000nt - 60º).
b. From the cosine function v(t) = 10 cos(1000nt - 60º):
- The angular frequency (ω) is 1000n rad/s.
- The frequency in hertz (f) can be found using the formula f = ω / 2π: f = (1000n) / (2π) Hz.
- The phase angle (φ) is -60º.
- The period (T) can be found using the formula T = 1/f: T = 2π / (1000n) seconds.
- The rms voltage value (Vrms) can be found using the formula Vrms = Vm / √2, where Vm is the amplitude: Vrms = 10 / √2 = 5√2 V.
c. To find the time-average power (P_avg) delivered to a 25n resistance (R), use the formula P_avg = (Vrms^2) / R: P_avg = ((5√2)^2) / (25n) = 50 / 25n = 2/n W.
Learn more about angular frequency here:
https://brainly.com/question/16845343
#SPJ11
Radius Ratio Rule is not much of a big topic in the chapter "The Solid State". However, it plays a very important role in the determination of a stable structure in an ionic crystal. It also helps in the determination of the arrangement of the ions in the crystal structure. Let us study this radius-ratio rule in detail and how it affects the stability and arrangement of a structure.
The Radius Ratio Rule helps determine a stable structure and arrangement of ions in an ionic crystal by calculating the ratio of cation and anion radii, determining the coordination number, and predicting the crystal structure.
The Radius Ratio Rule plays an important role in determining a stable structure in an ionic crystal, as well as the arrangement of ions in the crystal structure. This rule is based on the ratio of the radii of the cation (positively charged ion) to the anion (negatively charged ion) in a crystal lattice.
1: Calculate the radius ratio
To apply the Radius Ratio Rule, first calculate the ratio of the cation radius (r+) to the anion radius (r-). This is done using the formula:
Radius Ratio (RR) = r+ / r-
2: Determine the coordination number
Next, use the calculated radius ratio to determine the coordination number, which represents the number of anions surrounding a cation in the crystal lattice. The coordination number can be determined using the following ranges:
- RR ≤ 0.155: Coordination number = 2
- 0.155 < RR ≤ 0.225: Coordination number = 3
- 0.225 < RR ≤ 0.414: Coordination number = 4
- 0.414 < RR ≤ 0.732: Coordination number = 6
- 0.732 < RR ≤ 1.000: Coordination number = 8
3: Predict the crystal structure
Finally, use the coordination number to predict the crystal structure of the ionic compound. Common crystal structures and their corresponding coordination numbers include:
- Linear (CN = 2)
- Trigonal planar (CN = 3)
- Tetrahedral (CN = 4)
- Octahedral (CN = 6)
- Cubic (CN = 8)
You can learn more about Radius Ratio at: brainly.com/question/14080614
#SPJ11
first, suppose bx=0bx=0 . find the y coordinate yyy of the point at which the electron strikes the screen. express your answer in terms of ddd and the velocity components vxvxv_x and vyvyv_y .
The y-coordinate of the point at which the electron strikes the screen is simply equal to the distance (d) the electron travels.
What is Velocity?
Velocity is a vector quantity that describes the rate at which an object changes its position in a particular direction with respect to time. It includes both the magnitude (speed) and direction of motion of an object. Velocity is commonly used in physics, engineering, and other fields to describe the motion of objects.
The force experienced by a charged particle moving through a magnetic field is given by the Lorentz force equation:
F = q(v × B)
where:
F = Lorentz force (measured in units of force, such as newtons, N)
q = charge of the particle (measured in units of charge, such as coulombs, C)
v = velocity of the particle (measured in units of velocity, such as meters per second, m/s)
B = magnetic field (measured in units of magnetic field, such as tesla, T)
Since By = 0, the Lorentz force equation simplifies to:
F = q(vx * Bz)i + q(vy * Bz)j
where i and j are the unit vectors in the x and y directions, respectively.
The electron will be deflected in the y-direction due to the Lorentz force acting on it. The deflection in the y-direction can be calculated using the equation:
Fy = q(vy * Bz)
Setting Fy = 0 (since the electron strikes the screen), we can solve for vy:
0 = q(vy * Bz)
vy = 0
This means that the y-component of the velocity (vy) of the electron is zero when the electron strikes the screen.
The y-coordinate (y) of the point at which the electron strikes the screen is given by the equation:
y = d - vy * t
Since vy = 0, the y-coordinate simplifies to:
y = d
Learn more about Velocity from the given link
https://brainly.com/question/24445340
#SPJ1
Whlch of the following statements about the motion of the two masses Is/are correct? Select all that apply. The linear velocity of mi is the same as the linear velocity of m^(2) The angular velocity of m ls less than the angular velocity of m^(2) The lincar velocity of m s less than the lincar velocity of m^(2) The linear velocity of m is greater than the linear velocity of m^(2) The angular velocity of m is greater than the angular velocity of m^(2) The angular velocity of mi is the same as the angular velocity of m^(2)
Option A is Correct answer. The linear velocity of mi is the same as the linear velocity of m² The angular velocity of m ls less than the angular velocity of m²
The pace at which the angular location of a rotating body changes is referred to as the angular velocity. The rate at which the object's displacement changes over time while it moves in a straight line is referred to as linear velocity.
a) The first statement is correct - the linear velocity of mi is the same as the linear velocity of m², but the second statement is incorrect - the angular velocity of m is less than the angular velocity of m².
b) The first statement is incorrect - the linear velocity of m is less than the linear velocity of m², but the second statement is correct - the linear velocity of m is greater than the linear velocity of mm².
c) Both statements are incorrect - the angular velocity of m is less than the angular velocity of m², and the angular velocity of mi is not the same as the angular velocity of m².
Learn more about angular velocity here
https://brainly.com/question/20410914
#SPJ11
Option A is Correct answer. The linear velocity of mi is the same as the linear velocity of m² The angular velocity of m ls less than the angular velocity of m²
The pace at which the angular location of a rotating body changes is referred to as the angular velocity. The rate at which the object's displacement changes over time while it moves in a straight line is referred to as linear velocity.
a) The first statement is correct - the linear velocity of mi is the same as the linear velocity of m², but the second statement is incorrect - the angular velocity of m is less than the angular velocity of m².
b) The first statement is incorrect - the linear velocity of m is less than the linear velocity of m², but the second statement is correct - the linear velocity of m is greater than the linear velocity of mm².
c) Both statements are incorrect - the angular velocity of m is less than the angular velocity of m², and the angular velocity of mi is not the same as the angular velocity of m².
Learn more about angular velocity here
https://brainly.com/question/20410914
#SPJ11
two electrostatic point charges of -13 uC and -16 uC exert repulsive forces on each other of 12.5 N what is the distance between the two charges?
The distance between the two point charges is 3.88 x 10⁻⁵ meters.
We use the Coulomb's law to solve this problem. Coulomb's law states that the electric force between two point charges is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.
Formula for Coulomb's law is;
F = k × (q₁ × q₂)/r²
where; F = electric force between the two charges
k = Coulomb's constant, approximately equal to 8.99 x 10⁹ Nm²/C²
q₁ and q₂ = charges of the two point charges
r = distance between the two point charges
Given; q₁ = -13 uC = -13 x 10⁻⁶ C (converting from microCoulombs to Coulombs)
q₂ = -16 uC = -16 x 10⁻⁶ C (converting from microCoulombs to Coulombs)
F = 12.5 N
We can put these values into the formula and solve for r;
12.5 = (8.99 x 10⁹) × ((-13 x 10⁻⁶) × (-16 x 10⁻⁶)) / r²
Simplifying;
12.5 = (8.99 x 10⁹) × (208 x 10⁻¹²) / r²
12.5 = (8.99 x 10⁹) × (2.08 x 10⁻¹⁰) / r²
Now, we can rearrange equation to solve for r;
r² = (8.99 x 10⁹) × (2.08 x 10⁻¹⁰) / 12.5
r² = 1.508 x 10⁻⁹
Taking the square root of both sides;
r = √(1.508 x 10⁻⁹)
r ≈ 3.88 x 10⁻⁵ meters
To know more about Coulomb's law here
https://brainly.com/question/506926
#SPJ1
For men taking the the Air Force Physical Fitness Test, the best possible time to run 1.5 miles is in less than
A. 15 minutes, 30 seconds
B. 13 minutes, 36 seconds
C. 9 minutes, 12 seconds
D. 10 minutes, 23 seconds
Please select the best answer from the choices provided.
A
B
C
D
Answer:
B. 13 minutes, 36 seconds
Explanation:
the maximum time allowed for men to achieve the highest score (maximum points) in the 1.5 mile run component of the Air Force Physical Fitness Test.
A lens placed 13.0 cm in front of an object creates an upright image 2.00 times the height of the object. The lens is then moved along the optical axis until it creates an inverted image 2.00 times the height of the object. How far did the lens move?
Answer: 26 cm
Explanation:
Calculate the equilibrium constant K for the isomerization of glucose-1-phosphate to fructose-6-phosphate at 298 K.
The equilibrium constant K for the isomerization of glucose-1-phosphate to fructose-6-phosphate at 298 K is 0.2 .
The equilibrium constant K for the isomerization of glucose-1-phosphate to fructose-6-phosphate at 298 K can be calculated using the formula:
K = [Fructose-6-phosphate]/[Glucose-1-phosphate]
where [Fructose-6-phosphate] and [Glucose-1-phosphate] are the concentrations of the respective molecules at equilibrium.
The isomerization reaction can be represented by the following equation:
Glucose-1-phosphate ⇌ Fructose-6-phosphate
At equilibrium, the rates of the forward and reverse reactions are equal, and the concentrations of the two isomers remain constant. Therefore, the equilibrium constant K can be calculated using the concentrations of the two isomers at equilibrium.
Assuming that the initial concentration of glucose-1-phosphate is 1 M, and the equilibrium concentration of fructose-6-phosphate is 0.2 M, we can calculate the equilibrium constant K as follows:
K = [Fructose-6-phosphate]/[Glucose-1-phosphate] = 0.2/1 = 0.2
Therefore, the equilibrium constant K for the isomerization of glucose-1-phosphate to fructose-6-phosphate at 298 K is 0.2. This value indicates that the equilibrium lies towards the fructose-6-phosphate side of the reaction, meaning that fructose-6-phosphate is the more stable isomer at equilibrium.
Learn more about equilibrium constant here
https://brainly.com/question/15118952
#SPJ11
the sound intensity at a distance of 17 m from a noisy generator is measured to be 0.23 w/m2. what is the sound intensity at a distance of 31 m from the generator?
The sound intensity at a distance of 31 meters from the generator is approximately [tex]0.0687 W/m^2[/tex]
To calculate the sound intensity at a different distance, we can use the inverse square law, which states that the intensity is inversely proportional to the square of the distance. Here's a step-by-step explanation:
1. Write down the initial intensity (I1), initial distance (D1), and the new distance (D2).
I1 = [tex]0.23 W/m^2[/tex]
D1 = 17 m
D2 = 31 m
2. Apply the inverse square law formula, which is:
[tex]I2 = I1 * (D1^2 / D2^2)[/tex]
where I2 is the new intensity we want to find.
3. Substitute the values into the formula:
[tex]I2 = 0.23 * (17^2/ 31^2)[/tex]
4. Perform the calculations:
I2 = 0.23 * (289 / 961)
5. Calculate the new intensity (I2):
I2 ≈ [tex]0.0687 W/m^2[/tex]
To learn more about sound intensity click here https://brainly.com/question/14695848
#SPJ11
The sound intensity at a distance of 31 meters from the generator is approximately [tex]0.0687 W/m^2[/tex]
To calculate the sound intensity at a different distance, we can use the inverse square law, which states that the intensity is inversely proportional to the square of the distance. Here's a step-by-step explanation:
1. Write down the initial intensity (I1), initial distance (D1), and the new distance (D2).
I1 = [tex]0.23 W/m^2[/tex]
D1 = 17 m
D2 = 31 m
2. Apply the inverse square law formula, which is:
[tex]I2 = I1 * (D1^2 / D2^2)[/tex]
where I2 is the new intensity we want to find.
3. Substitute the values into the formula:
[tex]I2 = 0.23 * (17^2/ 31^2)[/tex]
4. Perform the calculations:
I2 = 0.23 * (289 / 961)
5. Calculate the new intensity (I2):
I2 ≈ [tex]0.0687 W/m^2[/tex]
To learn more about sound intensity click here https://brainly.com/question/14695848
#SPJ11
Anybody know this…..
The calculated value of the heat energy released by the system is 196.16 mJ.
Calculating Q, the heat energy released by the systemTo find Q, we can use the following equation:
Q = m * C * ΔT
where:
Q is the heat energy absorbed or released by the system (in joules)m is the mass of the substance (in grams)C is the specific heat capacity of the substance (in J/g·K)ΔT is the change in temperatureFirst, let's convert the given temperature from °C to K:
Cyn6 = 2100 5/53 degrees C = 2373.24 K
-5°C = 278.15 K
Next, we can use the following equation to calculate C, the specific heat capacity of Cyn6:
λ = Q / (m * ΔT)
Solving for C:
C = λ/ (m * ΔT)
Substituting the given values:
C = (3.9 * 10^6 J/mol) / (238 g/mol * 5.53 K)
C = 2963.21 J/g·K
Finally, we can calculate Q:
Q = m * C * ΔT
Substituting the given values:
Q = (238 g) * (2963.21 J/g·K) * (278.15 K)
Q = 196163613 J
Rewrite as
Q = 196.16 mJ (mega joules)
Therefore, the heat energy released by the system is 196.16 mJ.
Read more about specific heat capacity at
https://brainly.com/question/18214410
#SPJ1
vlock 1 is 1kg and b is 3 kg after collision they sticke together, what is kinetic energy of a
If block 1 is 1kg and b is 3 kg after the collision they stick together. In this case, the velocity is 0, resulting in zero kinetic energy for object A after the collision.
In order to calculate the kinetic energy of object A after the collision, we need to know the initial velocity of both objects and the type of collision (i.e., whether it is elastic or inelastic).
If we assume that the collision is perfectly inelastic, meaning the objects stick together and move as a single mass after the collision, we can use the law of conservation of momentum. The momentum before the collision is given by the sum of the momenta of the two objects:
Initial momentum = Momentum of A + Momentum of B
Since object A has a mass of 1 kg and object B has a mass of 3 kg, assuming they were initially at rest, the initial momentum of the system is 0.
After the collision, the objects stick together and move with a combined mass of 1 kg + 3 kg = 4 kg.
Let's assume the velocity of the combined mass after the collision is v.
Final momentum = Momentum of combined mass = mass of combined mass × velocity of combined mass
Final momentum = 4 kg × v
According to the law of conservation of momentum, the initial momentum and the final momentum of a system should be equal. Therefore, we can set up an equation as follows:
Initial momentum = Final momentum
0 = 4 kg × v
Solving for v, we get v = 0 m/s.
Since the velocity of the combined mass after the collision is 0 m/s, the kinetic energy of object A would also be 0 J, as kinetic energy is calculated using the equation KE = 0.5 × mass × velocity². So, the kinetic energy is 0 for object A.
You can learn more about kinetic energy at: brainly.com/question/26472013
#SPJ11
A shopper in a supermarket pushes a buggy with a force of 50N directed at an angle 20 degrees below the horizontal. What work is done on the buggy if the shopper pushes it 30m?
Answer:
Work = 1409.54 J
Explanation:
Work = Force*distance*cosine
[tex]Work = 30*50*cos(20)\\Work = 1409.54 J[/tex]
A 46 g golf ball leaves the tee at a velocity of 94 m/s. It was struck with a force of 2400 N. Assuming that the force was uniform during the impact, how long was the club in contact with the ball (what is the duration of the impact)? a. 0.25 b. 0.02 c. 2s d.002s
The correct option is (d) 0.002 s. The time taken for the club in contact with the ball is 0.02s when it was struck with a force of 2400N.
To answer this question, we can use the equation:
impulse = force × time
Impulse is the change in momentum of the golf ball. Momentum is calculated as mass × velocity. Since the golf ball is initially at rest, the impulse is equal to the final momentum.
First, convert the mass of the golf ball from grams to kilograms: 46 g = 0.046 kg.
Now, calculate the final momentum of the golf ball:
momentum = mass × velocity
momentum = 0.046 kg × 94 m/s
momentum = 4.324 kg·m/s
Next, use the impulse equation to find the time (duration of impact):
impulse = force × time
4.324 kg·m/s = 2400 N × time
Now, solve for the time:
time = 4.324 kg·m/s / 2400 N
time ≈ 0.0018 s
To learn more about velocity click here https://brainly.com/question/17127206
#SPJ11
A continuous-time signal xc(t) is band limited such that it has no spectral components for |omega| > 277(1000). This signal is sampled with sampling rate fs = 1/7s producing the sequence x[n] = xc(nTs). Then length-L sections of the sampled signal are extracted via time windowing as in Fig. 8-19 and analyzed with an N-point FFT. The resulting N DFT coefficients are samples of the spectrum of the continuous-time signal xc(t) with a spacing of delta f Hz. For efficiency in computation, assume that N is a power of two. Both fs and N can be chosen at will subject to the constraints that aliasing be avoided and N = 2v. Determine the minimum value of N, and also fs, so that the frequency spacing delta f between DFT coefficients is less than or equal to 5 Hz. Assume that the window is a Hann window whose length L is half the FFT length, N. For the value of N determined in (a), determine the spectral peak width (as measured between zero crossings). Give the answer in hertz. The result should be larger than 5 Hz, indicating that frequency resolution of narrow peaks is different from frequency sampling of the spectrum.(b) Assume that the window is a Hann window whose length L is half the FFT length, N. For the value of N determined in (a), determine the spectral peak width (as) measured between zero crossings). Give the answer in hertz. The result should be larger than 5 Hz, indicating that frequency resolution of narrow peaks is different from frequency sampling of the spectrum.
Because of this, the spectral peak width between zero crossings is around 70 Hz, which is higher than the 5 Hz frequency difference between DFT coefficients. This shows that the frequency sampling of the spectrum and the frequency resolution of narrow peaks are different.
Bandwidth of xc(t), B = 277(1000) Hz
Sampling rate, fs = 1/7 s
Frequency spacing between DFT coefficients, delta f = 5 Hz
Window type: Hann window of length L = N/2
(a) To find the minimum value of N and fs such that delta f <= 5 Hz:
Since the bandwidth of xc(t) is 277(1000) Hz, according to the Nyquist sampling theorem, the minimum sampling rate required to avoid aliasing is 2B = 554(1000) Hz. However, in this case, the signal is already sampled with a sampling rate of 1/7 s, which is higher than the minimum required rate.
delta f = fs/N
Substituting the given values, we get:
5 = (1/7)/N
N = 28
Therefore, the minimum value of N required is 28. To find the corresponding value of fs, we can rearrange the above equation:
fs = Ndelta f = 285 = 140 Hz
(b) To find the spectral peak width as measured between zero crossings:
The spectral peak width depends on the window used for analysis. In this case, we are using a Hann window of length L = N/2. The spectral peak width can be approximated as:
as ≈ 2.44*(delta f)(N/L)
Substituting the given values, we get:
as ≈ 2.445*(28/(28/2))
as ≈ 70 Hz
Learn more about frequency sampling visit: brainly.com/question/29669249
#SPJ4
In a ring of current with radius, r=2.81 cm, if dl covers 5.79 degrees (Q = 5.799) of the ring, what is the length of the chunk of the ring (what is the length of dl)? embaring current with radius, r=2.81 cm, if di covers 5 A +z direction
The length of the chunk of the current ring (dl) is approximately 0.284 cm.
To find the length of the chunk of the current ring (dl), we need to use the formula:
[tex]dl = (Q/360) * 2\pi r[/tex]
Where Q is angle covered by dl, r is radius of the ring, and π is constant value (3.14159...).
Substituting the given values, we get:
[tex]dl = (5.799/360) * 2\pi (2.81 cm)[/tex]
dl = 0.0941 cm
Therefore, the length of the chunk of the ring (dl) is 0.0941 cm.
dl = r * θ
where
r = 2.81 cm (radius)
[tex]θ = Q * (\pi / 180)[/tex] (angle in radians)
Step 1: Convert angle from degrees to radians:
[tex]θ = 5.79° * (\pi / 180) = 0.101[/tex]radians (approx.)
Step 2: Calculate dl:
dl = 2.81 cm * 0.101 radians = 0.284 cm (approx.)
Learn more about current here:
https://brainly.com/question/14252753
#SPJ11
how much heat is required to raise the temperature of 5kg of water from 5c to 35c
Solution. The 400 kcal of heat energy required to increase the water's temperature.
How much heat does it take to elevate 2 kilos water to 5 K?The energy required to elevate it in this instance is: 524.18=41.8J since the mass equals 2.0g, the water's specific heat capacity is 4.18J/g/K, and the rise in temperature is 5.0°C=5K.
How so much heat is needed to raise 2 kg of iron's temperature?Q = 2.00 kg, 449 J/kgoC, 23 oC, and 20654 J Q is equal to 2.00 kg, 449 J/kg at 23 o C, and 20654 J. This is equivalent to about 20.7 kJ. We can add a positive sign since the iron needs (or absorbs) this heat. Hence, the response to the query is (a).
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ1
An airfoil with a characteristic length L=0.2 ft is placed in airflow at p=1 atm and T.=60F with free stream velocity V=150 ft/s and convection heat transfer coefficient h=21 Btu/h-ft2.oF. A second larger airfoil with a characteristic length L=0.4 ft is placed in the airflow at the same air pressure and temperature, with free stream velocity V=75 ft/s.Both airfoils are maintained at a constant surface temperature T=180F To,h Cair T.,h Determine the heat flux from the second airfoil [solution:q=1260 Btu/h-ft]
The heat flux from the second airfoil is q=1260 Btu/h-ft . The negative sign indicates that heat is being transferred from the airfoil to the surrounding air.
The heat flux from the second airfoil can be determined using the equation:
q = h × (Tsurface - Tfree stream)
where q is the heat flux, h is the convection heat transfer coefficient, Tsurface is the constant surface temperature of the airfoil, and Tfree stream is the free stream temperature.
For the first airfoil with a characteristic length of L=0.2 ft, the free stream velocity is V=150 ft/s. Therefore, the free stream temperature can be calculated using the formula:
T_free stream = T + (V² / 2×Cp)
where Cp is the specific heat capacity of air at constant pressure.
Substituting the given values, we get:
T_free stream = 60F + (150² / 2×0.24) = 578.75F
Using this value and the given convection heat transfer coefficient of h=21 Btu/h-ft2.oF, we can calculate the heat flux for the first airfoil as
q_1 = 21 × (180 - 578.75) = -8433.75 Btu/h-ft
Note that For the second airfoil with a characteristic length of L=0.4 ft, the free stream velocity is V=75 ft/s. Using the same formula as before, we can calculate the free stream temperature as:
T_free stream = 60F + (75² / 2×0.24) = 325.78F
Using the same constant surface temperature of T=180F and the given convection heat transfer coefficient of h=21 Btu/h-ft2.oF, we can calculate the heat flux for the second airfoil as:
q_2 = 21 ×(180 - 325.78) = 1260 Btu/h-ft
Learn more about heat flux here
https://brainly.com/question/30708042
#SPJ11
A 3.0 kg block slides with a speed of 1.3 m/s on a frictionless horizontal surface until it encounters a spring. What initial speed should the block have to compress the spring by 1.2 cm? Express your answer using two significant figures.
The initial speed the block should have to compress the spring by 1.2 cm is 0.21 m/s.
The spring will compress due to the kinetic energy of the block being transferred into potential energy stored in the spring. We can use the formula for elastic potential energy:
Elastic potential energy = (1/2) k x^2
Where k is the spring constant and x is the distance the spring is compressed. We can rearrange this formula to solve for k:
k = 2 * (Elastic potential energy) / x^2
Since the block is initially sliding on a frictionless surface, there is no external work done on the block-spring system. Therefore, the initial kinetic energy of the block must be equal to the elastic potential energy stored in the spring:
(1/2) m v^2 = (1/2) k x^2
Substituting the expression for k from above:
(1/2) m v^2 = (Elastic potential energy) / x
Solving for v:
v = sqrt((2 * Elastic potential energy) / (m * x))
Substituting the given values:
v = sqrt((2 * (1/2) k x^2) / (m * x))
v = sqrt((k / m) * x^2)
v = sqrt((spring constant) * (distance compressed) / (mass))
Plugging in the given values:
v = sqrt((k / m) * x^2) = sqrt((200 N/m) * (0.012 m)^2 / 3.0 kg) = 0.21 m/s
For more such questions on Spring.
https://brainly.com/question/14280940#
#SPJ11
18) if the intensity level by 10 identical engines in a garage is 100 db, what is the intensity level generated by each one of these engines?
The intensity level generated by each of the ten identical engines in a garage is 90 dB.
Assuming that the engines are producing the same amount of sound and the sound waves are spreading uniformly in all directions, we can use the logarithmic relationship between sound intensity level (IL) and the number of sound sources (N):-
IL = 10 log10(N) + 10 log10(I)
where I = the intensity level of a single source.
In this case, we have N = 10 engines and IL = 100 dB, so we can solve for I:-
100 = 10 log10(10) + 10 log10(I)
100 = 10 + 10 log10(I)
90 = 10 log10(I)
log10(I) = 9
I = 10^9 W/m^2
Therefore, the intensity level generated by each one of these engines is:-
IL = 10 log10(I) = 10 log10(10^9) = 90 dB
Learn more about engines: https://brainly.com/question/25870707
#SPJ11
A glass plate 0.9 cm thick has a refractive index of 1.50. How long does it take for a pulse of light to pass through the plate? A. 3.0x 10-1s B. 4.5 x 10-s C. 3.0 × 10-¹s D. 4.5 x 10-10s [c-3.0.x 108 mms-¹]
The time taken for a pulse of light to pass through a material is 4.5 x 10⁻¹¹ s,
option D.
What is the time taken by the pulse of light?The time taken for a pulse of light to pass through a material is calculated as follows;
t = d / v
Where;
d is the distance traveled by the pulsev is the speed of light in the materialThe speed of light in the material is calculated as;
v = c / n
v = c / n
v = (3 x 10⁸ m/s) / 1.5
v = 2 x 10⁸ m/s
The time taken is calculated as;
t = d / v
t = 0.009 m / 2.0 x 10⁸ m/s
t = 4.5 x 10⁻¹¹ s
Learn more about time of pulse here: https://brainly.com/question/11245663
#SPJ1
Use the fact that the change in the mechanical energy is equal to the work done by friction to find the value of the friction force acting on the cart. Use the electronic balance to find the mass of the friction block, and then find the coefficient of friction between the friction block and the track.
The friction force acting on the cart can be found by calculating the change in mechanical energy of the system.
The mechanical energy of the system is equal to the work done by friction, which can be calculated using the equation W=Fd, where F is the friction force, and d is the distance the cart has traveled.
To calculate the friction force, first find the mass of the friction block using an electronic balance. Then use the equation F=μmg, where μ is the coefficient of friction between the friction block and the track, m is the mass of the friction block, and g is the acceleration due to gravity.
This equation can be used to calculate the coefficient of friction between the friction block and the track. Once the coefficient of friction is known, the equation F=μ can be used to calculate the friction force.
By knowing the change in mechanical energy and the coefficient of friction, the friction force can be calculated and the motion of the cart can be further understood.
Know more about friction force here
https://brainly.com/question/30280752#
#SPJ11
A coil is connected to a 12V battery. After 0.2s the current through the coil is 50mA After 10s the current is 0.3A (i) Determine the the time constant of the coil (ii) Determine the resistance of the coil (iii) Determine the current after 0.5s.
The time constant of the coil is approximately 6.288s, the resistance of the coil is 40Ω, and the current after 0.5s is 22.4mA.
(i) To determine the time constant (τ) of the coil, we'll use the formula,
τ = (t1 - t2) / (ln(I1 / I2))
where t1 = 0.2s, I1 = 50mA (0.05A), t2 = 10s, and I2 = 0.3A.
τ = (0.2 - 10) / (ln(0.05 / 0.3)) = -9.8 / (ln(1/6)) ≈ 6.288s
(ii) To determine the resistance (R) of the coil, we'll use the formula,
R = V / I = 12V / 0.3A
R = 40Ω
(iii) To determine the current (I) after 0.5s, we'll use the formula,
I(t) = V/R * (1 - e^(-t/τ))
where V = 12V, R = 40Ω, t = 0.5s, and τ = 6.288s.
I(0.5) = (12 / 40) * (1 - e^(-0.5 / 6.288)) ≈ 0.3 * (1 - e^(-0.0795)) ≈ 0.0224A or 22.4mA
In conclusion, the coil's time constant is roughly 6.288 seconds, its resistance is 40 ohms, and its current after 0.5 seconds is 22.4 mA.
Learn more about "resistance": https://brainly.com/question/17563681
#SPJ11
The time constant of the coil is approximately 6.288s, the resistance of the coil is 40Ω, and the current after 0.5s is 22.4mA.
(i) To determine the time constant (τ) of the coil, we'll use the formula,
τ = (t1 - t2) / (ln(I1 / I2))
where t1 = 0.2s, I1 = 50mA (0.05A), t2 = 10s, and I2 = 0.3A.
τ = (0.2 - 10) / (ln(0.05 / 0.3)) = -9.8 / (ln(1/6)) ≈ 6.288s
(ii) To determine the resistance (R) of the coil, we'll use the formula,
R = V / I = 12V / 0.3A
R = 40Ω
(iii) To determine the current (I) after 0.5s, we'll use the formula,
I(t) = V/R * (1 - e^(-t/τ))
where V = 12V, R = 40Ω, t = 0.5s, and τ = 6.288s.
I(0.5) = (12 / 40) * (1 - e^(-0.5 / 6.288)) ≈ 0.3 * (1 - e^(-0.0795)) ≈ 0.0224A or 22.4mA
In conclusion, the coil's time constant is roughly 6.288 seconds, its resistance is 40 ohms, and its current after 0.5 seconds is 22.4 mA.
Learn more about "resistance": https://brainly.com/question/17563681
#SPJ11
a hair breaks under a tension of 1.2 n. what is the diameter of the hair? the tensile strength is 2.2 ✕ 108 pa.
The diameter of the hair is approximately 3.12 micrometers.
To find the diameter of the hair, we can use the formula for tensile strength:
Tensile strength = Force / Area
We know that the tension force is 1.2 N and the tensile strength is 2.2 ✕ 108 Pa. We can rearrange the formula to solve for the area (which will give us the cross-sectional area of the hair):
Area = Force / Tensile strength
Substituting the values we have:
Area = 1.2 N / 2.2 ✕ 108 Pa
Area = 5.45 ✕ 10^-9 m^2
Now, we can use the formula for the area of a circle to find the diameter:
Area = π/4 ✕ diameter^2
Solving for diameter:
diameter = √(4 ✕ Area / π)
Substituting the value we found for the area:
diameter = √(4 ✕ 5.45 ✕ 10^-9 / π)
diameter = 3.12 ✕ 10^-6 m
Therefore, the diameter of the hair is approximately 3.12 micrometers.
To know more about tensile strength click here:
https://brainly.com/question/25748369
#SPJ11
a 500 kg car is parked on a hill with a 5° slope. what is the magnitude of the friction force acting on the car?
The magnitude of the friction force acting on the car is 3434 N when a 500 kg car is parked on a hill with a 5° slope.
The magnitude of the friction force acting on the car can be calculated using the formula Ff = μFn, where Ff is the friction force, μ is the coefficient of friction, and Fn is the normal force. In this case, the car is parked on a hill with a 5° slope, so the normal force acting on the car is equal to its weight, which can be calculated as Fg = mg = 500 kg x 9.81 m/s² = 4905 N.
The coefficient of friction depends on the surfaces in contact. Let's assume the car's tires are made of rubber and the road surface is concrete. In this case, the coefficient of static friction between rubber and concrete is typically between 0.7 and 0.9. Let's take a conservative estimate of μ = 0.7.
Now we can calculate the friction force as Ff = μFn = 0.7 x 4905 N = 3434 N. Therefore, the magnitude of the friction force acting on the car is approximately 3434 N, which is the force that opposes the car's motion down the hill due to gravity.
For more such questions on Friction force.
https://brainly.com/question/17050027#
#SPJ11
two astronauts, one of mass 65 kg and the other 86 kg , are initially at rest together in outer space. they then push each other apart. how far apart are they when the lighter astronaut has moved 15 m ?
The two astronauts are about 20.77 meters apart when the lighter astronaut has moved 15 meters.
By use conservation of momentum to solve this problem. According to Newton's third law of motion, when the astronauts push each other, they will experience equal and opposite forces, and their momentum will be conserved.
Therefore, the product of their masses and velocities before and after the push should be equal:
(m₁)(v₁) + (m₂)(v₂) = (m₁)(v₁') + (m₂)(v₂')
where m₁ and m₂ are the masses of the astronauts, v₁ and v₂ are their velocities before the push (which are both zero), and v₁' and v₂' are their velocities after the push. We can solve for v₁' and v₂':
v₁' = (m₁/m₂)(-v₂)
v₂' = (m₂/m₁)(-v₁)
where the negative signs indicate that the astronauts are moving in opposite directions.
Let's plug in the values we know:
m₁ = 65 kg
m₂ = 86 kg
v₁ = 0 m/s
v₂ = 0 m/s
v₁' = ?
v₂' = ?
Using the equations above, we get:
v₁' = (65/86)(-0 m/s) = 0 m/s
v₂' = (86/65)(-0 m/s) = 0 m/s
This tells us that the astronauts will move away from each other with equal and opposite velocities. Let's call the distance between them x, and let's assume that the lighter astronaut (m1) moves 15 m. Then we can set up an equation based on the fact that the total distance they move apart is x:
x = 15 m + (86/65)(-15 m)
Simplifying this equation, we get:
x = 15 m - 20.77 m
x = -5.77 m
This negative value for x means that the lighter astronaut has moved 15 m to the left, while the heavier astronaut has moved 5.77 m to the right. The distance between them is therefore the sum of these distances:
distance = 15 m + 5.77 m
distance = 20.77 m
So the two astronauts will be about 20.77 meters apart when the lighter astronaut has moved 15 meters.
To know more about two astronauts
https://brainly.com/question/6967503
#SPJ4
\A capacitor is constructed of two identical conducting plates parallel to each other and separated by a distance d. The capacitor is charged to a potential difference of Vi by a battery, which is then disconnected. (Remember that a capacitor's job is to store charge!) What is the magnitude of the electric field between the plates? A. Vo/d B.Vo/d C. d/Vo D. Vo/d2
The correct answer for magnitude of electric field between the plates is B. Vo/d
The magnitude of the electric field between the plates of a capacitor is given by the formula E = V/d, where V is the potential difference across the plates and d is the distance between them. In this case, the capacitor is charged to a potential difference of Vi by a battery, so the magnitude of the electric field between the plates is E = Vi/d. Therefore, the correct answer is A. Vi/d.
Hi! To find the magnitude of the electric field between the plates of the capacitor, we can use the formula for electric field (E) in a parallel plate capacitor, which is:
E = V/d
Here, V is the potential difference (Vi) and d is the distance between the plates.
So, the magnitude of the electric field between the plates is:
E = Vi/d
This corresponds to option B in your given choices. Therefore, the correct answer is:
B. Vo/d
Learn more about electric field here:
https://brainly.com/question/15800304
#SPJ11
if the wide flange beam is subjected to a shear of v=30 kN, determine the shear force resisted by the web. set w=200 mm.
The shear force resisted by the web of the wide flange beam can be determined by dividing 20 kN by the web thickness (t), which can be calculated based on the specific dimensions and properties of the beam.
To determine the shear force resisted by the web of a wide flange beam subjected to a shear of v=30 kN and with a web width of w=200 mm, we can use the following formula:
V = (2/3) × Fv × t × w
Where:
V = Shear force resisted by the web
Fv = Shear stress in the web
t = Web thickness
First, we need to find the shear stress in the web, which can be calculated using:
Fv = V / (t × w)
Substituting the given values, we get:
Fv = 30 kN / (t × 200 mm)
Next, we can substitute this value of Fv in the first equation to find the shear force resisted by the web:
V = (2/3) × Fv × t × w
V = (2/3) × (30 kN / (t × 200 mm)) × t × 200 mm
Simplifying, we get:
V = (20 kN) / t
Learn More about flange beam here :-
https://brainly.com/question/30035399
#SPJ11
acceleration due to gravity of a free-falling object is 9.8 m/s2. express this in millimeters/millisecond2
The acceleration due to gravity in millimeters/milliseconds² is 0.0098 mm/ms².
To express the acceleration due to gravity of a free-falling object (9.8 m/s²) in millimeters/millisecond², follow these steps:
1. Convert meters (m) to millimeters (mm): Since there are 1000 millimeters in a meter, multiply the given value by 1000.
9.8 m/s² × 1000 mm/m = 9800 mm/s²
2. Convert seconds (s) to milliseconds (ms): Since there are 1000 milliseconds in a second, divide the obtained value by 1000² (1000 multiplied by 1000).
9800 mm/s² ÷ (1000 ms/s × 1000 ms/s) = 9800 mm/s² ÷ 1000000 ms²
3. Calculate the final value:
9800 mm/s² ÷ 1000000 ms² = 0.0098 mm/ms²
So, the acceleration due to gravity of a free-falling object expressed in millimeters/millisecond² is 0.0098 mm/ms².
Learn more about acceleration:
https://brainly.com/question/460763
#SPJ11
The acceleration due to gravity in millimeters/milliseconds² is 0.0098 mm/ms².
To express the acceleration due to gravity of a free-falling object (9.8 m/s²) in millimeters/millisecond², follow these steps:
1. Convert meters (m) to millimeters (mm): Since there are 1000 millimeters in a meter, multiply the given value by 1000.
9.8 m/s² × 1000 mm/m = 9800 mm/s²
2. Convert seconds (s) to milliseconds (ms): Since there are 1000 milliseconds in a second, divide the obtained value by 1000² (1000 multiplied by 1000).
9800 mm/s² ÷ (1000 ms/s × 1000 ms/s) = 9800 mm/s² ÷ 1000000 ms²
3. Calculate the final value:
9800 mm/s² ÷ 1000000 ms² = 0.0098 mm/ms²
So, the acceleration due to gravity of a free-falling object expressed in millimeters/millisecond² is 0.0098 mm/ms².
Learn more about acceleration:
https://brainly.com/question/460763
#SPJ11