Suppose that in cases B, C, and D in problem 1, each combination of springs were replaced by a single spring such that the motion of the block is the same as before the replacement. We will call the spring constant of this new spring the effective spring constant of the original combination. Quantitatively, the effective spring constant, keff , may be defined by the relationship Sigma Fvector block, spring = -Keff , where Sigma block, spring is the sum of all forces on the block by the springs, and is the position of the block with respect to the equilibrium position. Rank the four cases according to keff, from largest to smallest. Explain. Use your ranking above and the relationship T = 2pi root m/keff to rank the cases according to period of oscillation. Explain. Use your ranking from part a and the relationship E total = 1/2 keffA2 to rank the cases according to total energy. Explain.

The statement of dalton's law of partial pressures is the total pressure by a mixture of gases is equal to the sum of the partial pressures of each gas that makes up the mixture. The correct answer is B.

The pressure that each gas would produce if it occupied the same volume of the mixture at the same temperature alone is referred to as the partial pressure.

the law of partial pressure known as Dalton's Law A combination of gases exerts a pressure that is equal to the sum of the pressures that each gas exerts on its own. Each gas exerts pressure directly proportional to the amount of that gas present in the gas mixture.

In closed vessels over water, Dalton found that oxygen interacted with either one or two volumes of nitric oxide. This ground-breaking observation of integral multiple proportions served as crucial experimental support for his fledgling atomic theories.

Your question is incomplete but most probably your full question was

Which of the following is a statement of daltons law of partial pressure

A. The total pressure of a mixture of gases is the product of the partial pressures of each gas in the mixture

B. The total pressure of a mixture of gases is the sum of the partial presaure of each gas that makes up the mixture

C. gases can exist as mixtures at STP only

D. in a mixture of two gases, the pressure of each gas is 1/2 of the total pressure

E. the partial pressure of a gas is equal to the total pressure of the mixture

Learn more about Dalton's law of partial pressures here:- brainly.com/question/14119417

#SPJ4

The centripetal force is 7.3 m/s and tension  is 7.30 m/s .

What is tension ?

Any two physical objects in touch have the ability to exert forces on one another. Based on the kinds of objects in touch, we give these contact forces various names. When a rope, string, chain, or cable is one of the things applying the force, the force is referred to as tension.

What is speed ?

Speed is the rate of change in location of an item, expressed in metres per second. For instance, the speed of an item is one metre per second if it starts at the origin and goes three metres in three seconds. Speed is easily calculated by dividing a distance by a time.

Tension (force) in string = mv²/R = 0.90v²/0.80 = 1.125v²

Tension (force) in string = 60.0 N

set Tensions equal:

1.125v² = 53.33

v = v53.33

v = 7.30 m/s (speed of mass at which string breaks)

circumference of path mass travels = 2pR = 5.02 m

time of one rev that gives a tangential speed of 7.3 m

T = 5.02/7.3 = 0.69 sec

rev/sec = 1/0.69 = 1.45 rps

60 x 1.45 = 87 rpm

centripetal force = Tension

mv^2/r = T

0.9xv^2/0.8 =60

v=7.3 m/s

Therefore, the centripetal force is 7.3 m/s and tension  is 7.30 m/s .

Learn more about tension from the given link.

https://brainly.com/question/138724

#SPJ4

You want to start a climb at 160 knots while cruising at 190 mph. It would be reasonable to perform the initial pitch change upon starting the climb (full panel) by increasing the rear elevator pressure until the Attitude indicator displays.

Once the knots are set, you can adjust the pressure until the pitch attitude indicator approximates the pitch attitude required for the 160-knot climb. The approximate pitch attitude needed for the 160-knot climb. You want to start a climb at 130 knots while cruising at 160 knots. It is proper to make the initial pitch change while starting a climb (full panel) by increasing the back elevator pressure until the attitude indicator displays the approximate pitch attitude needed for a 130-knot ascent. You want to start a climb at 130 knots while cruising at 160 knots. It is proper to adjust the initial pitch while commencing the climb (full panel) by raising the back elevator pressure till the end.

To learn more about  elevator pressure please click on below link

https://brainly.com/question/29665127

#SPJ4

Answer:

Below is the explanation

Explanation:

You use Newton's second law which states:

Force (N) = mass (kg) x acceleration (m/s squared)

So we substitute:

6000 = ? x 2

Rearrange so:

? = 6000/2

which = 3000 kg

Don is attempting to build muscle mass for his first body-building competition. According to the American College of Sports Medicine, he should be eating 1.5 to 1.7 grams per kilogram of body weight of protein per day.

Muscle is a system of coordinated contractile tissues that is used to perform tasks more effectively. The physical appearance and cell location of the muscular systems in humans are used to classify them. Strained (or skeletal), cardiac, and smooth muscles are the three categories (or nonstriated). The majority of the muscular tissue in the body is striated muscle, which is mostly connected to the skeleton. The somatic nervous system directs the multinucleated fibers, which cause stresses on the skeleton like those produced by pulleys and levers to cause movement. Sinoatrial node, the pacemaker of the heart, controls the rhythmic contraction of cardiac muscle. Cardiovascular muscle is a particular striated muscle with several centrally positioned nuclei that is made up of elongated cells, however it is not controlled voluntarily. Blood lines the smooth muscle of the viscera.

Learn more about muscle here:

https://brainly.com/question/2937599

#SPJ4

It is not desirable to have large areas of forest plants replaced by oil palms because animals and plants may be affected in regions of fragmented habitat, which is an important issue in ecosystem disturbance and loss of biodiversity.

Ecosystem disturbance is an ecological concept that makes reference to the different human activities and natural processes (such as earthquake catastrophes) that are to break the delicate internal homeostatic equilibrium of the ecosystems. Moreover, loss of biodiversity refers to the loss of variation due to the extinction of populations and even species.

Therefore, with this data, we can see that ecosystem disturbance and loss of biodiversity are fundamental processes and they have been associated with the process of replacement of native trees in natural forests with oil palms, which have negative outcomes for the surrounding environment.

Learn more about the loss of biodiversity here:

https://brainly.com/question/7101235

#SPJ1

The mass of the fish on the end of the pole, in kilograms m =2.090Kg.

What is Force?

Force is an influence that can cause an object to change its motion, direction, shape, or other physical attributes. Forces can be applied to objects, creating a change in their acceleration, velocity, or momentum. Forces can be either contact forces, such as pushing or pulling on an object, or non-contact forces, such as gravity, magnetism, and electricity. Forces can be described in terms of magnitude, direction, and point of application. Magnitude is the strength of the force, direction is the path the force is applied, and point of application is the point on the object where the force is applied. Forces can also be classified as balanced or unbalanced. Balanced forces occur when two forces of equal magnitude and opposite direction act on an object, resulting in no net force. Unbalanced forces occur when two forces of unequal magnitude act on an object, resulting in a net force.

Given that,

F2 = 240N

Angle = 83.5 degree

Length = 4.1m

Distance = 0.35m

How much force, F1 in newtons ?

What kind of fish is that hanging off the end of the pole?

Thus,

Calculating Torque about ‘A’

For equillibrium ∑τa= 0

F1 * L + F2 * (L – d) = 0

F1 * L= - F2* (L – d)

F1L SinΘ= F2(L – d) SinΘ

F1 = F2 (L – d)/L

F1 = 240 (4.1 – 0.35)/4.1

F1 = 219.51N

For equillibrium ∑ Fnet = 0

F2 + F1 + mg = 0

mg = F2- F1

m = F2 - F1/ g

m = 2.090Kg

To learn more about Force:

https://brainly.com/question/12970081

#SPJ1

The height of the cliff that a stone is dropped from the top, the splash it made as it hit the water below was heard 5.0 s later is 857.5 m.

Sound can bounce when it hits an object that has a hard surface and is not easily penetrated by waves. Examples of objects that can reflect sound are glass walls, iron, zinc, cave walls, and seabeds.

This reflected sound can be used to measure the depth of the sea or the distance of the walls of the cave passage. One of the uses of sound reflection is to know the depth of the sea or the distance of the cave walls.

The equation to determine the distance is:

s = ½ (v) (t)

s = distance or height

t = time

v = velocity of the sound wave (343 m/s)

We have,

Time  = 5.0 s

Velocity of the sound wave = 343 m/s

So, the height of the cliff:

s = ½ (v) (t)

= ½ (343) (5)

= 857.5 m

The question is incomplete, it should be:

A stone is dropped from the top of a cliff. The splash it makes when striking the water below is heard 5.0 s later. How high is the cliff?

Learn more about sound wave here: https://brainly.com/question/1199084

#SPJ4

"Most of the new star formation in the galaxy is found in the spiral arms."

Spiral arms are the regions of strong star formation and are more prominent in blue light. From the centre of spiral and barred spiral galaxies, these regions extend.

Transient weaknesses in the gases that encourage star formation and produce turbulence lead to spiral arms. In other words, spiral arms contain a lot of gases, which are the primary building blocks needed for the development of new stars.

They are not hard or permanent structures, as evidenced by the presence of spiral arms. A density wave is currently thought to circle a spiral galaxy, creating spiral arms.

The thin disk of the galaxy contains all of the spiral arms.

To know more about galaxies:

https://brainly.com/question/12532606

#SPJ4

Subcutaneous tissue fat functions similarly to insulation in your home in numerous areas of your body. This fat absorbs shock to underlying structures and aids in protecting the deep body systems like muscles and organs from temperature changes.

Which of the following causes a decrease in metabolism?

Crash dieting, starvation, or fasting all cause the body to reduce its metabolism in an effort to conserve energy. BMR can fall by up to 15%, and if lean muscle mass is lost as well, BMR is further decreased.

Which tissue serves as insulating material, a cushion of protection, and a source of energy?

The bottom layer of skin on your body is called the hypodermis. It has a variety of purposes, such as defending your body from injury, insulating your body, storing energy, and attaching your skin to your muscles and bones.

To know more about person's metabolic visit;

https://brainly.com/question/9375050

#SPJ4

Answer:16

Explanation:

as F=BIL so by placing value's B is magnetic field 4 and i is current 2A and l is length that js 2 m so answer is

Given: i=10A,B=0.15 T,θ=45

∘

and l=2 m

Force on a current carrying wire of finite length =

F

=l(

i

×

B

)

Hence, magnitude of force, F=Bilsinθ

=0.15×10×2×sin45

∘

=

2

3

N

 The speed of a bobsled is increasing because it has an acceleration of 2.4 m/s2. at a given instant in time 1363.6N.

Acceleration refers to the rate at which the velocity and direction of a moving object change over time. Anything is said to be sped when it goes straighter and faster or slower. Therefore, even though the speed is constant, travel on a circle increases due to the constant change in direction.

The rate at which a displacement varies is measured by its velocity. Speed changes occur at an accelerated rate. Its magnitude and orientation are both present, making it a vector quantity. As the rate at which velocity changes, acceleration is likewise a vector quantity.

To know more about acceleration visit:

https://brainly.com/question/11936480

#SPJ4

It's called the Phantom because the galaxy's surface brightness is low.

Because of the galaxy's low surface brightness, it is known as the Phantom. Of all the Messier objects that amateur astronomers view using tiny telescopes, it is the most challenging to locate. The galaxy almost faces Earth, which accounts for the low surface brightness.

M74 is a star in the constellation Pisces that is around 32 million light-years from Earth. Through modest telescopes, the galaxy appears as a dim patch of light with an apparent magnitude of only 10. The ideal time to view it is around November. A spiral galaxy with a majestic pattern, M74 is the ideal illustration.

To learn more about Phantom visit:https://brainly.com/question/13148367

#SPJ4

Answer:

ΔS= -1 J/K

Explanation:

Using this data

Heat Q= -256.0J

Temperature T=420.0 K

To find

Entropy change ΔS

Solution

We know that the entropy change of system is ΔS is given by

ΔS=Q/T

We have take heat value Q as negative because the heat is removed from heat reservoir

So

ΔS=(-256J/470K)

ΔS= -1 J/K

Please visit the link provided below to learn more on heat conduction:

https://brainly.com/question/14787908

#SPJ4

larger in a rope with a smaller angle.

When nellie newton dangles by a pair of ropes, each at different angle from the vertical, the rope tension will be greater in the rope having the larger in a rope with a smaller angle.

The pulling force transmitted axially by a string, rope, chain, or other similar object, or by each end of a rod, truss member, or other similar three-dimensional object is referred to as tension. The action-reaction pair of forces acting at each end of said elements can also be referred to as tension. The polar opposite of compression might be tension.

The ends of a string or other object that transmits tension will apply forces in the direction of the string at the point of attachment to the objects to which it is connected.

To know more about tension here:

https://brainly.com/question/29763438#

#SPJ4

√F1²+F2², because this force reflects the overall force the cup has applied to the platform.

The change in direction and centripetal force. A centripetal force is applied to any item travelling in a circle (or along a spherical route). Towards other words, the item is being physically pushed or pulled in the direction of the circle's center. This is the necessary centripetal force.

Centripetal force is the name of the force exerted on a particle that is rotating in a circle. It is this centripetal force that is focused inward that prevents the particle from deviating from or losing its circular course.

To know more about Centripetal forces visit

brainly.com/question/11324711

#SPJ4

A jet of water squirts out horizontally from a hole near the bottom of the tank shown in the figure. If the hole has a diameter of 3.80 mm, the height h of the water level in the tank is 44.1 cm

The height of the water level can be calculate as follows:

According to kinematics, if the water's initial velocity when it exits the tank is, its horizontal range is given by

d = v√(2y/y)

where, y is the acceleration caused by gravity and is the vertical distance from the ground to the hole.

Torricelli's law provides the velocity of the fluid flowing out of the hole. the velocity  of water coming out of the hole is

v=√(2gh)

where,h is the tank's top-to-bottom distance, as depicted in the picture.

The horizontal range equation is used to calculate the water's exit velocity from the hole:

d= v√(2y/g)

v= d x √(g/2y)

and since d= 0.600 m an y= 1 m

v= 0.600  x √(9.8/2(1))

v= 0.600 x 4.9

v= 2.94 m/s

Now, we can  use Torricelli's theorem to find the height

v=√(2gh)

h = v²/2g

h = (2.94)² / 2 (9.8)

h = 0.441 m = 44.1 cm

Your question is incomplete because of missing picture but most probably your full question attached below

Learn more about Torriceli's law at https://brainly.com/question/13091900

#SPJ4

On two of the particles, the strengths and directions of the applied force are shown. 2 N to the right, 2 N to the right, and more than 2 N to the right

a) 2 N rightward

for the center of mass to be stationary,

Net force = 0

SO, 2N rightward

(b) 2N rightward

for the center of mass to move with constant velocity

Net force = 0

So, 2N rightward

(c) greater than 2N rightward

for the center of mass to accelerate in rightward

Net force should be in rightward

So, greater than 2N rightward

In mechanics, a force is any action that has the potential to change, maintain, or deform a body's motion. The three principles of motion outlined by Isaac Newton in his Principia Mathematica are frequently used to illustrate the concept of force (1687). Newton's first law states that a body at rest or moving uniformly in a straight line will stay in that state until a force is applied to it. According to the second law, a body will accelerate (change in velocity) in the direction of any external force acting on it. The strength of the external force directly correlates with the strength of the acceleration.

Learn more about force here:

https://brainly.com/question/13191643

#SPJ4

In a vacuum, an electromagnetic wave is moving through the air. The wavelength is 1x10^7m and the frequency is 3x10^15Hz while the  direction of the electric field is along the z-axis.

Given the magnetic field along z axis (B) = 3.0muTsin(1.0x10^7x  - 3.0*10^15 t)

The formula for magnetic field  is B = B0sin(wt+kx)

For direction of wave by comparing the equations we have

kx +(- 3.0 x 10^15 ) = 0

x = 3.0 x 10^15 /k  in positive direction of x axis

The direction of propogation is along x axis and the magnetic field in y axis. The electric field is in both directions. So E along z axis

B0 = 3x10-7x4πT

ω = -3.0 x 10^15

∧ = 2π/k =  2x3.14/1.0x10^7 = 0.68/1.0x10^7 = 0.68x10-7

The wavelength ∧ of the wave is = 0.68x10-7m

frequency (f) = c/∧ = 3x10^8/0.68x10-7 = 4.41x10^15Hz

The frequency f of the wave is 4.41x10^15Hz

To learn more about magnetic field click here https://brainly.com/question/24397546

#SPJ4

The sun can fuse hydrogen for over ten billion years, while a star twice as massive runs out of hydrogen in two billion years.

Given that they have more fuel than stars with smaller masses, you may assume that big stars would endure longer. However, the cores of these monsters burn through fuel more quickly because they are much hotter and fuse elements at far faster rates.

For more than 10 billion years, a star like a sun can happily burn hydrogen into helium. But in under two billion years, a star twice as massive as the sun exhausts its supply of hydrogen. In just a few hundred million years, a star eight times as massive as the Sun will run out of fuel. Additionally, the speed of each phase in the fusion process increases over time.

To learn more about the sun and stars, visit the link below:

brainly.com/question/28097233

#SPJ4

The speed of the cart just before it hit the spring is 3.42 m/s.

Elastic potential energy is the energy that is stored when a force is applied to deform an elastic object.

Given the mass of the cart is 12 kg, the spring constant is 220 N/m, and the compressed length is 80 cm.

Given that the runaway grocery cart compresses the string. When this cart stops, the kinetic energy (KE) of this cart becomes zero because of maximum compression. This KE will be converted to the elastic potential energy of the spring. Then,

[tex]\begin{aligned}U&=\frac{1}{2}kx^2\\&=\frac{1}{2}\times220\times0.80^2\\&=\mathrm{70.4\;J}\end{aligned}[/tex]

This elastic potential energy is equal to the initial KE.

[tex]\begin{aligned}70.4&=\frac{1}{2}\times 12\times v^2\\140.8&=12v^2\\v^2&=11.73\\v&=\mathrm{3.42\;m/s}\end{aligned}[/tex]

The answer is 3.42 m/s

To know more about elastic potential energy:

https://brainly.com/question/29311518

#SPJ4

Moon Illusion is an Optical Phenomenon. This occurs because when the moon is near the horizon, Earthly things that resemble the moon on your retina generate a misunderstanding or inaccurate perception of distance and size.

The brain interprets the low moon as being bigger since it is lower in the sky than the higher moon.

The mechanism behind size-distance perception in everyday life, which transforms planar pictures that fall on the retina into a perception of hard objects moving in space, is related to the moon illusion.

What happens when the mechanism acts in an uncommon circumstance is what causes the moon illusion. In typical perception, the angular size of the light image stimulating our eyes expands or shrinks as rigid objects move in depth (distance).

The sense of hard objects with shifting depth perception is produced naturally by the brain in response to these changing stimuli. The ground and horizon make the moon appear comparatively close when it is close to the horizon.

Due to the moon's shifting apparent position in depth while the light stimulus stays constant, the moon appears extraordinarily huge due to the brain's size-distance mechanism.

To read more about optical phenomenons, visit https://brainly.com/question/28195646

#SPJ4

The performance of a digital communication system is quantified by the probability of bit detection problems in the presence of thermal noise.

In the context of wireless communications, the major source of thermal noise is the addition of random signals arising from the vibration of atoms in the receiver electronics.

Gaussian: The probability distribution of the noise samples is Gaussian with a zero mean, i.e., in the time domain, the samples can acquire both negative and positive values in addition.

the values near zero have a higher chance of occurrence while the values far away from zero are less likely to appear.

As a result, the time domain average of a greater number of noise samples is equal to zero.

To know more about Gaussian noise:

https://brainly.com/question/15048637

#SPJ4

The volume of a gas in liters if 2.95 mol has a pressure of 0.760 atm at a temperature of 52oc is 116.584.

volume of a gas = 2.95 × 0.760 × 52 = 116.584

We understand temperature as the average translational kinetic energy linked to the disordered motion of atoms and molecules, and the kinetic temperature as derived from kinetic theory provides reasonable accuracy. In light of the fact that higher energy molecules are colliding with lower energy molecules and transferring energy to them, it follows naturally that the flow of heat is from a region of high temperature toward a region of lower temperature. Since temperature only measures the kinetic energy portion of internal energy, it is not directly proportional to internal energy, so two objects with the same temperature do not necessarily have the same internal energy (see water-metal example). The three commonly used temperature scales are used to measure temperatures (Celsius, Kelvin, and Fahrenheit).

Learn more about temperature here:

https://brainly.com/question/1191204

#SPJ4

The time taken (in minutes) for the light from the sun to reach the Earth is 8.3 minutes.

The speed of sunlight is 300,000 kilometres per second. The basic equation "time= (distance/speed)" can be used to determine how long it takes for sunlight to reach Earth.

We are given that,

Speed of light = c = 3×10⁸ m/s

Distance from sun to earth = d = 93 million miles = 148.8× 10⁹m

Thus to calculate the time of sun light which is reached to earth by the equation,

t = d / c

t = (148.8 × 10⁹m)/( 3×10⁸ m/s)

t = 496 sec

t = 8 min 3 sec.

Therefore , the sunlight reached to earth in 8min 3sec.

To know more about time

https://brainly.com/question/8012273

#SPJ4

An ac voltage source is attached to an LCR series circuit. The phase difference between current and voltage is /3 when L is taken out of the circuit. The circuit has a power factor of one.

LCR series circuit, which stands for inductance-capacitance-resistance, can only function as one of the three components on its own. It is also employed to boost voltage and raise the voltage that travels through each component of the circuit individually. This voltage has the potential to be far higher than the external voltage that is applied to the electrical circuit.

IXc = sin (pi/4)

Xc = R

The phasor will look like this when C is eliminated.

Xl = Xc

The supplied circuit is therefore in resonance.

LCR circuit's power factor is 1 cos(o).

Learn more about series circuit here

https://brainly.com/question/11409042

#SPJ4

The separation between the first maxima for red light (λ = 700nm) and violet light (λ = 400nm) = 80 x 10⁻⁵ cm

Light interference is a condition when two or more light waves combine to form a combined light wave. The condition for this light interference is that the light waves come from a coherent source, so that the amplitude, wavelength, and frequency are the same, and the phase difference is always fixed.

The question is incomplete, it should be:

What is the separation between the first maxima for red light (λ = 700nm) and violet light (λ = 400nm)?

We have,

Distance between slits = 0,5 mm = 5 x 10⁻⁴ m

Distance between the slit and the screen = 5.5 m

λ red = 700 nm =

λ violet = 400 nm

So, The separation between the first maxima:

Sin ∅m = mλ/d

= (1 x 400 x 10⁻⁹)/5 x 10⁻⁴

= 80 x 10⁻⁵ cm

The question is incomplete, it should be:

White light falls on two narrow slits separated by 0.50 mm. The interference pattern is observed on a screen 5.5 m away. (a) What is the separation between the first maxima for red light (λ = 700 nm) and violet light (λ = 400 nm)?

Learn more about light interference here: https://brainly.com/question/17112134

#SPJ4

The payback period of the new equipment is closest to 17.8%

Simple rate of return is equal to annual operating income minus the initial investment.

=$65000/365000    

=17.8%

The payback period describes how long it will take to return the cost of an investment. The time it takes for an investment to break even can be summed up in this way. The payback period is important because people and businesses invest money primarily to be compensated. The payback period is the amount of time an investor would need to invest in a project before they would be able to repay their initial investment. The investment's break-even point is closely related to it.

Instead of using the units of a break-even analysis, Payback Period employs years to quantify investment opportunities and risk in a rapid and straightforward manner.

Learn more about payback period here:

https://brainly.com/question/13978071

#SPJ4

(a) The total distance of the bus is 10 m.

(b) The total displacement of the bus is 2.83 m.

(c) The average speed of the bus is 2 m/s.

(d) The average velocity of the bus is 0.57 m/s.

The total distance of the bus is the sum of all the distance covered by the bus and it is calculated as follows;

distance = 2 m + 5 m + 3 m = 10 m

The total displacement of the bus is calculated as follows;

resultant horizontal displacement = 2 m east

resultant vertical displacement = 5 m - 3 m = 2 m North

Total displacement = √ ( 2² + 2² )

Total displacement = 2.83 m

The average speed is calculated as;

average speed = 10 m / 5 s = 2 m/s

The average velocity is calculated as;

average velocity = 2.83 m / 5 s = 0.57 m/s

Learn more about average velocity here: https://brainly.com/question/24445340

#SPJ1