Steam passes steadily through a turbine and condenser as shown in the figure below. After expanding through the turbine and producing 1000kW of power, the steam is at a pressure of 0.08 bar and a quality of 874: It enters a shell-and-tube heat exchanger where the steam now condenses on the outside of tubes through which cooling water flows, this condensate continues to flow, finally exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 58kg/s. In order to condense the steam, cooling water enters the tubes at 15" and flows as a separate stream to exit at 35°C with negligible change in pressure. Stray heat transfer is negligible as are kinetic and potential effects. Considering the steam inside the turbine as a system, is the system best described as open, closed, or isolated? What is the mass flow rate of steam entering the turbine in kg/s? What is the enthalpy at the inlet of the turbine in kJ/kg? What is the mass flowrate of the cooling water in kg/s? If the diameter of the cooling water line is 10cm, what is the velocity of the cooling water in m/s when it enters the condenser? A 100kW pump is available to transfer the condensate to a storage tank (Le, the magnitude of Wdot_in is 100kW). What would be the maximum increase in height in meters that the pump could move the water assuming that the temperature, pressure, and velocity of the condensate are roughly equal at the inlet and outlet of the pump section?

Therefore, the input force is 9615.38N

T0 determine the input force needed  0.78 to raise a house corner from its foundation we need to use the formula for mechanical advantage.

Mechanical advantage = output force/ input force

Given the output force  to be 7500N and the mechanical advantage 0.78.

We can rearrange the the formula

IF = 7500/0.78

IF = 9615.38N

Therefore, the input force is 9615.38N

Learn more  about input force below.

https://brainly.com/question/29741758

#SPJ1

Answer: 98 kN/m

Explanation:

Given

Mass of elephant [tex]m=5000\ kg[/tex]

Spring compresses from [tex]1\ m\ (100\ cm) \text{to}\ 50\ cm[/tex]

i.e. change in length is [tex]100-50=50\ cm[/tex]

spring force is given by  [tex]kx[/tex]

where k=spring constant

x=change in length

The weight of elephant must be equal to the spring force

[tex]\Rightarrow W=kx\\\Rightarrow 5000\times 9.8=k\times 0.5\\\Rightarrow k=98,000\ N/m\ or\ 98\ kN/m[/tex]

Answer:

2.69 × 10^(-10) N

Explanation:

To calculate the required value of power, we need to consider the force exerted by the radiation pressure and equate it to the weight of the disk.

The force exerted by the radiation pressure is given by:

F = (2RΔt)P/c

where:

F is the force,

R is the radius of the disk,

Δt is the thickness of the disk,

P is the power of the laser,

c is the speed of light.

We are given:

R = 8.00 μm = 8.00 × 10^(-6) m (radius of the disk)

Δt = 2.00 μm = 2.00 × 10^(-6) m (thickness of the disk)

ρ = 7.00 × 10^2 kg/m² (average density of the disk)

The weight of the disk is given by:

W = mg

where:

m is the mass of the disk,

g is the acceleration due to gravity.

The mass of the disk can be calculated using its average density and volume:

m = ρV

The volume of the disk is given by:

V = πR²Δt

Substituting the expressions for mass and volume into the equation for weight, we have:

W = ρVg = ρ(πR²Δt)g

Setting the force equal to the weight, we have:

F = W

(2RΔt)P/c = ρ(πR²Δt)g

Simplifying the equation:

2RP/c = ρπR²g

Now we can solve for the power P:

P = (ρπRg)/(2c)

Substituting the given values:

P = (7.00 × 10^2 kg/m²)(π)(8.00 × 10^(-6) m)(9.8 m/s²)/(2(3.00 × 10^8 m/s))

Calculating this expression:

P ≈ 2.69 × 10^(-10) kg⋅m/s² = 2.69 × 10^(-10) N

So, the required power Pay is approximately 2.69 × 10^(-10) N (newtons).

We can utilize Einstein's mass-energy equivalence equation, E = mc², where E represents the energy. The work done on the particle is equal to the change in energy.

When the particle is at rest, its energy is solely its rest energy, which is given by E = mc². As the particle is accelerated to a speed of 0.902 c, its total energy increases. The change in energy (ΔE) is the difference between the final energy and the initial rest energy.

The final energy of the particle when it reaches a speed of 0.902 c is given by E = γmc², where γ is the Lorentz factor. The Lorentz factor is defined as γ = 1/√(1 - (v/c)²), where v is the velocity of the particle.

By substituting the given values into the Lorentz factor equation, we can calculate the Lorentz factor for the particle. With the Lorentz factor known, we can determine the final energy of the particle.

The work done on the particle is equal to the change in energy, so the work can be calculated as ΔE = (γ - 1)mc². By substituting the values into the equation and expressing the answer as a multiple of mc², we can determine the work required to accelerate the particle to the given speed.

Learn more about Einstein's mass-energy equivalence equation here:

https://brainly.com/question/4005271

#SPJ11

The flux across the portion of the sphere is  a³/ 16.

To find the flux across the portion of the sphere in the first octant, we need to use a parametrization of the surface. The sphere can be parametrized as:

r(θ, φ) = (a sin φ cos θ, a sin φ sin θ, a cos φ)

where 0 ≤ θ ≤ π/2 and 0 ≤ φ ≤ π/2.

The normal vector to the surface is:

n = r_θ × r_φ

where r_θ and r_φ are the partial derivatives of r with respect to θ and φ, respectively.

We have:

r_θ = (-a sin φ sin θ, a sin φ cos θ, 0)

r_φ = (a cos φ cos θ, a cos φ sin θ, -a sin φ)

So:

n = (-a² sin² φ cos θ, -a² sin² φ sin θ, -a² sin φ cos φ)

The flux of F across S is given by:

∫∫S F ⋅ n dS

where F is the vector field and dS is the surface area element. In this case,

F = (0, 0, z)

dS = |r_θ × r_φ| dθ dφ

So we have:

∫∫S F ⋅ n dS = ∫∫D F(r(θ, φ)) ⋅ (r_θ × r_φ) dθ dφ

= ∫0(0[tex]^{\pi } /2[/tex] )∫0[tex]^{\pi } /2[/tex] (a cos φ) (-a² sin² φ cos θ i - a² sin² φ sin θ j - a² sin φ cos φ k) ⋅ (-a² sin φ i - a² sin φ j - a² cos φ k) dθ dφ

= ∫0^(π/2) ∫0[tex]^{\pi } /2[/tex] a³ sin³ φ cos²φ dθ dφ

= (a³ / 4) ∫0[tex]^{\pi } /2[/tex] (sin 4φ / 4) dφ

= (a³ / 16) [1 - 0]

= a³/ 16

To know more about vector field

https://brainly.com/question/31866032

#SPJ4

The average value of the voltage induced in a tape head over the interval from t = 0 to t = 3 can be found by evaluating the definite integral of the given function. Rounded to the nearest volt, the answer is C) 6502 volts.

To find the average value of the voltage v over the interval from t = 0 to t = 3, we need to evaluate the definite integral of the function [tex]v = t^2 e^3^t[/tex] with respect to t over this interval. The average value is given by the formula:

Average value = (1 / (b - a)) * ∫(a to b) v dt,

where a and b represent the starting and ending points of the interval, respectively.

Substituting the given values a = 0 and b = 3 into the formula, we have:

Average value = (1 / (3 - 0)) * ∫(0 to 3) [tex]t^2 e^3^t[/tex]dt.

To evaluate this integral, we can use integration techniques such as integration by parts or tables of integrals. Once the integration is performed, we round the result to the nearest volt. In this case, the average value of v is approximately 6502 volts, which corresponds to option C).

Learn more about voltage here:

https://brainly.com/question/13396105

#SPJ11

Explanation:

LIKE charge.....   if they were opposite (opposites attract) ...they would accelerate as they grew closer .....like charges REPEL and they get farther apart and decelerate ....

Answer:

Ekaryote cells

an organism consisting of a cell or cells in which the genetic material is DNA in the form of chromosomes contained within a distinct nucleus. Eukaryotes include all living organisms other than the eubacteria and archaea.

prokaryote cells

microscopic single-celled organism which has neither a distinct nucleus with a membrane nor other specialized organelles, including the bacteria and cyanobacteria

The sound intensity level of the ultrasound used to pulverize tissue during surgery is approximately 29.83 dB.

To determine the sound intensity level (β) in decibels (dB) for ultrasound with an intensity of  ([tex]10^{5}[/tex] W/[tex]m^{2}[/tex]), we can use the formula for sound intensity level

β = 10 * log10(I/I₀)

Where:

β is the sound intensity level in decibels,

I is the sound intensity of the ultrasound,

I₀ is the reference sound intensity.

In this case, the reference sound intensity corresponds to 104 W/[tex]m^{2}[/tex], which corresponds to 160 dB. Therefore, we have:

β = 10 * log10(I / 104)

Plugging in the given intensity of ultrasound ([tex]10^{5}[/tex] W/[tex]m^{2}[/tex]), we have:

β = 10 * log10([tex]10^{5}[/tex] / 104)

β = 10 * log10(961.54)

β = 10 * 2.983

β = 29.83 dB

Therefore, the sound intensity level of the ultrasound used to pulverize tissue during surgery is approximately 29.83 dB.

To know more about sound intensity level here

https://brainly.com/question/14670897

#SPJ4

C) fault-block mountain

The impulse exerted on the ball by the wall is -24i N s, the answer is option b.

The impulse exerted on the ball by the wall can be determined using the impulse-momentum theorem.

Impulse is equal to the change in momentum.

That is,

J = Δp

Since momentum is a vector,

p = mv

Substituting the values,

p(initial) = mv(initial) = 3.0 kg × (4i + 3j) m/s

p(initial) = 12i + 9j N s

p(final) = mv(final) = 3.0 kg × (-4i + 3j) m/s

p(final) = -12i + 9j N s

Change in momentum,

(Δp) = p(final) - p(initial)

      = (-12i + 9j) N s - (12i + 9j) N s

      = (-12 - 12)i + (9 - 9)j N s

      = -24i N s

Thus, the impulse exerted on the ball by the wall is -24i N s, which means that the answer is option b.

Learn more about the impulse:

brainly.com/question/29787317

#SPJ11

Answer:

The angle above the horizontal at which the pitcher throws the ball determines the distance the ball travels before returning to the height at which it was thrown

Explanation:

The baseball is thrown as a projectile and the range, 'R', of the baseball which is the distance the baseball travels before the height above the ground returns to the initial height  is given given as follows;

[tex]R = \dfrac{u^2 \cdot sin(2\cdot \theta )}{g}[/tex]

Where;

R = The range of the baseball = The horizontal distance away from the pitcher the ball reaches

u = The initial velocity with which the baseball was thrown

θ = The angle above horizontal a baseball pitcher throws the ball

g = The acceleration due to gravity ≈ 9.81 m/s²

From the the equation, when θ = 0, sin(θ) = sin(0) = 0 and the ball does not cover any horizontal distance before going lower than the height at which it was thrown, therefore, for the ball to travel further, the angle of launch, θ has to be larger than 0.

Answer:

Insulators is the correct answer

Explanation:

A few electrons make up the insulators, which allow for very little electrical current to flow. While the conductors are excellent electrical conductors. Rubber is a poor insulator compared to metal, which is a very good conductor.

The insulator is a material that consists of a few electrons and they permit very little flow of electrical current. While the conductors are very good conductors of electricity. Metal is a very good conductor while rubber is a poor insulator.

Hence the answer is conductors possess free electrons, while insulators have few free electrons

The conductor has thus been used for wiring purposes and can be effectively used made to use energy; The insulator is a poor absorber and thus are unable to transfer energy.

Learn more about insulators follow.

brainly.com/question/19755578

SPJ6

In the subset number duplication example at the bottom of page 231, if the last record (2) was replaced with 1805, the Number Frequency Factor would remain the same.

The subset number duplication example is an example of the identification of the degree of duplication in a given group of data sets. It consists of records of numbers and their duplicates which are listed in order, the frequency with which each number is repeated, and the percentage of total numbers that each number represents.The given example contains a series of numerical values that represent the degree of duplication within a given group of data sets. By substituting the last record with the number 1805, the Number Frequency Factor would remain unchanged, as there is no instance of this number in the dataset. Hence, the number frequency factor would remain the same even after substituting the last record with 1805.

The units of the pre-outstanding variable An are indistinguishable from those of the rate consistent and will change contingent upon the request for the response. It has units of s1 for a reaction of first order. As a result, it is frequently referred to as the frequency factor.

Know more about Frequency Factor, here:

https://brainly.com/question/27723476

#SPJ11

Answer:

Cool.

Explanation:

What's the question..? :|

Answer:

η = 0.7

Explanation:

The refractive index of the material can be calculated by using the following formula:

[tex]\eta = \frac{c}{v}\\[/tex]

where,

η = refractive index of the material = ?

c = speedof light in vaccuum = 3 x 10⁸ m/s

v = speed of light in this material = 4.3 x 10⁸ m/s

Therefore,

[tex]\eta = \frac{3\ x\ 10^8\ m/s}{4.3\ x\ 10^8\ m/s}[/tex]

η = 0.7

Answer:

P=F/A where F is the weight of the water and A is the area on which it is resting. The weight of the water is mg. The mass of the water is dv where d is the density and v is the volume. Finally, the volume of the water in a vessel is equal to the area of the base of the vessel times the height of the vessel. (v=Ah)

Plugging everything in we get:

P = dAhg/A

So

P=dhg

So we have shown that liquid pressure is directly  proportional to height of liquid in a vessel.​

Two reasons why it is better to obtain the moment of inertia through a linear fit rather than by solving for I using specific points (ωmax and θ0) are:

Increased Precision: A linear fit allows for the consideration of a larger set of data points, which can provide a more accurate determination of the moment of inertia. By analyzing the relationship between θ and ω over a range of values, the linear fit captures the overall trend and minimizes the potential errors associated with individual data points. This leads to a more precise estimation of the moment of inertia compared to relying on only one or two specific points. Account for Nonlinearities: In some cases, the relationship between θ and ω may not follow a simple linear pattern. If nonlinearity exists, using a linear fit provides a more flexible approach to capture the overall trend. By fitting a line to the data, even if the relationship is not strictly linear, we can still obtain a reasonable approximation of the moment of inertia by considering the best-fit line that represents the general behavior of the system. This method accounts for potential nonlinearities and provides a more reliable estimate of the moment of inertia compared to a limited number of specific points.

To learn more about inertia, https://brainly.com/question/31045808

#SPJ11

The ideal gas law can be used to solve the problem. The relationship between pressure, temperature, volume, and the number of moles of gas is given by the ideal gas law. PV = nRT is the formula for the ideal gas law,  Where:P = pressure in atm, V = volume in Litersn = a number of moles, R = gas constant, T = temperature in Kelvin.

The temperature at which 0.444 mol of CO gas occupies 11.8 L at 889 torr can be calculated as follows ;

First, we must convert the pressure from torr to atm: 889 torr × 1 atm/760 torr = 1.17 atm.

Using the ideal gas law formula: PV = nRT.

We can solve for T.T = PV/nR where, P = 1.17 atmV = 11.8 Ln = 0.444 molR = 0.08206 L•atm/mol•K.

Substitute the given values,T = (1.17 atm × 11.8 L)/(0.444 mol × 0.08206 L•atm/mol•K)T = 379 K.

Convert Kelvin to Celsius by subtracting 273.15 from the value,379 K - 273.15 = 105.85°C ≈ 106°C.

Therefore, the temperature at which 0.444 mol of CO gas occupies 11.8 L at 889 torr is approximately 106°C. Hence, the correct option is E)106 °C.

Learn more about ideal gas law here ;

https://brainly.com/question/12624936

#SPJ11

The power of the eye when viewing an object 3.00 m away is 58.82 diopters (D).

What is power of the eye?

The power of the eye refers to its ability to refract light and focus it onto the retina, enabling clear vision at different distances. The power of the eye is measured in diopters (D).

In the case of the human eye, it is generally assumed to have an equivalent focal length of approximately 17 mm, which is equivalent to 0.017 m. This value represents the average refractive power of the eye.

To calculate the power of the eye when viewing an object 3.00 m away, we can use the following formula:

P = 1 / f

P = 1 / 0.017

P = 58.82 D

Therefore, the power of the eye when viewing an object 3.00 m away is approximately 58.82 diopters (D).

To learn more about power of the eye,

https://brainly.com/question/17166887

#SPJ4

The magnitude of the electric field just above the middle of the sheet is approximately 3.05 x 10⁶ N/C.

To find the electric field just above the middle of a large, flat, horizontal sheet of charge, we can use Gauss's law.

Gauss's law states that the electric field (E) due to a flat sheet of charge is directly proportional to the charge density (σ) and perpendicular to the sheet.

The charge density is given as 5.40 µC/m², which represents the charge per unit area of the sheet.

The electric field just above the middle of the sheet is the same as the electric field just below the sheet. This is because the sheet is infinitely large and uniformly charged, creating a symmetric electric field.

The formula to calculate the electric field just above the middle of the sheet is:

E = σ / (2ε₀)

Where σ is the charge density and ε₀ is the permittivity of free space, which is approximately 8.85 x 10⁻¹² C²/(N·m²).

Substituting the given values, we have:

E = (5.40 x 10⁻⁶ C/m²) / (2 x 8.85 x 10⁻¹² C²/(N·m²))

Simplifying, we get:

E = 3.05 x 10⁶ N/C

The direction of the electric field is perpendicular to the sheet and points away from it.

Learn more about electric field:

https://brainly.com/question/19878202

#SPJ11

a) The rest energy (Eₙ) is 1.305 x 10¹⁶ J.

b) The kinetic energy (Eₖ) is 83.71 J.

c) The statement that is true is " The kinetic energy is much smaller than the rest energy".

To compare the rest energy and kinetic energy of the baseball, we can use the equations:

a) The rest energy (Eₙ) can be calculated using Einstein's mass-energy equivalence formula:

Eₙ = m × c²

Where:

m is the mass of the baseball

c is the speed of light in a vacuum, which is approximately 3.00 x 10⁸ m/s

Given:

m = 0.145 kg

Using the formula:

Eₙ = 0.145 kg × (3.00 x 10⁸ m/s)²

Eₙ = 0.145 kg × 9.00 x 10¹⁶ m²/s²

Eₙ = 1.305 x 10¹⁶ J

b) The kinetic energy (Eₖ) can be calculated using the formula:

Eₖ = (1/2) × m × v²

Where:

m is the mass of the baseball

v is the velocity of the baseball

Given:

m = 0.145 kg

v = 34 m/s

Using the formula:

Eₖ = (1/2) × 0.145 kg × (34 m/s)²

Eₖ = 0.0725 kg × (1156 m²/s²)

Eₖ = 83.71 J

c) Comparing the rest energy and kinetic energy:

i) The kinetic energy is much bigger than the rest energy.

ii) The kinetic energy is approximately equal to the rest energy.

iii) The kinetic energy is much smaller than the rest energy.

In this case, the rest energy is approximately 1.305 x 10¹⁶ J, while the kinetic energy is 83.71 J. Therefore, statement iii) is true: the kinetic energy is much smaller than the rest energy.

Learn more about Einstein's mass-energy from the link given below.

https://brainly.com/question/15991401

#SPJ4

A pot containing 630 g of water is placed on the stove and is slowly heated from 21°C to 81°C, then the change in entropy of the water is 7200 J/K.

To calculate the change in entropy (ΔS) of water, we can use the formula:

ΔS = mcΔT / T

Where:

m is the mass of the water,

c is the specific heat capacity of water,

ΔT is the change in temperature, and

T is the initial temperature.

First, we need to find the specific heat capacity of water. The specific heat capacity of water is approximately 4.18 J/g°C.

Mass of water (m) = 630 g

Change in temperature (ΔT) = (81°C - 21°C) = 60°C

Initial temperature (T) = 21°C

Substituting these values into the formula, we get:

ΔS = (630 g) * (4.18 J/g°C) * (60°C) / (21°C)

Simplifying the equation:

ΔS = (630 g) * (4.18 J/g°C) * (60°C) / (21°C)

  = 630 * 4.18 * 60 / 21

  = 7200 J/K

Learn more about entropy:

https://brainly.com/question/6364271

#SPJ11

Answer:

Force = 0.42 Newton

Explanation:

Given the following data;

Spring constant, k = 2.1

Extension, e = 0.2m

To find the force, we would use the formula below;

Force = spring constant * extension

Force = 2.1 * 0.2

Force = 0.42 Newton

A 600-w TV receiver is turned on for 4 hours with nobody watching it. If electricity costs 10 cents/kWh, the amount of money wasted is cents. Therefore, the amount of money wasted in this case is 24 cents.

There are different steps to calculate the money wasted in this case. Here is the step-by-step solution to this problem:

First, we need to calculate the energy consumed in kWh:

Energy consumed = Power × Time Power = 600 W Time = 4 hours

Energy consumed = Power × Time Energy consumed = 600 W × 4 hours

Energy consumed = 2400 Wh.

To convert Wh into kWh, we need to divide the energy consumed by 1000:

Energy consumed = 2400 Wh = 2.4 kWh.

Now, we can calculate the amount of money wasted:

Cost of 1 kWh = 10 cents Cost of 2.4 kWh = 2.4 kWh × 10 cents/kWh

Cost of 2.4 kWh = 24 cents.  

A 600-w TV receiver is turned on for 4 hours with nobody watching it. If electricity costs 10 cents/kWh, the amount of money wasted is cents. The energy consumed by the TV receiver can be calculated by multiplying the power rating by the time it is used. In this case, the power rating is 600 W, and the time is 4 hours.

Therefore, the energy consumed is 600 W × 4 hours = 2400 Wh.

To convert the energy consumed into kWh, we need to divide it by 1000. So, 2400 Wh = 2.4 kWh. The cost of electricity is 10 cents per kWh.

Therefore, the cost of 2.4 kWh is 2.4 kWh × 10 cents/kWh = 24 cents.

This is the amount of money wasted by keeping the TV receiver turned on for 4 hours without anyone watching it. It is important to turn off electrical appliances when they are not in use to save electricity and reduce the electricity bill.

to know more about energy visit:

https://brainly.com/question/1932868

#SPJ11

Answer:

F=mv^2/r = 50x(900)/625 = 72N

The centripetal force of 180 N is acting on the girl who is in the roller coaster ride with a speed of 30 m/s in a horizontal circle with a radius of 25m.

A centripetal force is the force which makes a body follow a circular path. Here, the direction is always orthogonal to the motion of body and towards a fixed point of instantaneous center of curvature of path.

The centripetal force acting on an object in circular path can be calculated with the help of a formula:

F = mv²/r

where, F = centripetal force acting on the object,

m = mass of the object,

v = velocity of the object,

r = radius of the circular path.

By putting the given values into the formula, we get:

F = [50 × (30)²]/25

F = [50 × 900]/25

F = 4500/25

F = 180 N

Therefore, the centripetal force acting on the girl is 180 N.

Learn more about Centripetal force here:

https://brainly.com/question/14021112

#SPJ2

Answer:

V = 411.43 V

Explanation:

The two forces as a result of each of the 2 charges are;

F1 = kq1•q/r

F2 = kq2.q/r

Where r = r/2 since we are dealing with potential difference at a point midway between the charges.

q1 = 5 nC = 5 × 10^(-9) C

q2 = 3 nC = 3 × 10^(-9) C

k = 9 × 10^(9) N.m²/C²

r = 35 cm = 0.35m

r/2 = 0.35/2

Thus;

F1 = (9 × 10^(9) × 5 × 10^(-9) × q)/(0.35/2)²

F1 = 1469.39q

F2 = (9 × 10^(9) × 3 × 10^(-9) × q)/(0.35/2)²

F2 = 881.63q

Net force acting midway is;

F_net = F1 + F2

F_net = 1469.39q + 881.63q

F_net = 2351.02q

Now, we know that formula for electric potential is;

V = kq/r

Thus ;

V = Fr/q derived from the earlier equation for force we used.

Where F is F_net.

V = 2351.02q × r/q

V = 2351.02r

Recall that we are dealing with midpoint and r = r/2

Thus;

V = 2351.02 × 0.35/2

V = 411.43 V

Answer

A spherical bob creates more control for the simple pendulum experiment. An irregular bob like a large piece of paper for instance, will create too much air resistance for a basic classical experiment to yield predictable results within the academic lab.

After slowing down by 15 miles per hour and reducing the speed by one third, you are now going at 60 miles per hour.

If you are initially driving at a rate of one and a half miles per minute, it means you are traveling at a speed of 90 miles per hour (since there are 60 minutes in an hour).

In the second step, you slow down by 15 miles per hour. This reduces your speed to 75 miles per hour.

Finally, you reduce your speed by one third, which means you need to subtract one third of 75 from 75. One third of 75 is 25, so subtracting 25 from 75 gives you a speed of 50 miles per hour.

Therefore, after slowing down by 15 miles per hour and then reducing your speed by one third, you are now traveling at a speed of 50 miles per hour.

Learn more about Speed

brainly.com/question/17661499

#SPJ11