The steady-state creep rate at 1300 K and a stress level of 83 MPa(12,000 psi) is 1.77 × 10⁻⁵.
What is creep rate?Temperature-dependent time rate of material deformation under stress. It is the slope of the creep test's time-versus-creep diagram. The most common units are in/in/hr or % of elongation/hr. The slope of the portion of the creep vs. time diagram corresponding to secondary creep is known as the minimum creep rate.
Creep is the propensity of a solid material to move slowly or undergo permanent deformation when subjected to ongoing mechanical stresses. Long-term exposure to high stress levels that are still below the material's yield strength can lead to it. In materials heated for an extended period of time, creep is more severe and typically gets worse as the material gets closer to melting.
Learn more about creep rate
https://brainly.com/question/14042064
#SPJ4
FILL IN THE BLANK. Limited slip differential ______ can result from clutch parts that are worn; in some cases, changing the limited slip lubricating oil fixes the problem.
Growling and Chattering are signs of worn clutch components; in certain cases, changing the limited slip lubrication oil resolves the issue.
What impact would a lubricant level that was too low possibly have?Low oil levels starve component surfaces of lubricant, resulting in fast wear and eventual machine failure. Metal-on-metal friction can cause shaft, housing, and other machine damage, making this failure one of the most expensive ones.
In a manual transmission, which of the following is utilized to shift?In contrast to automatics, which only have two, manuals feature three pedals. The farthest pedal to the left is the clutch pedal. When changing from one gear to the next, including neutral, you utilize it to shift up or down.
To know more about lubricating oil visit :-
https://brainly.com/question/19481124
#SPJ1
As a highly flexible structure, __________ can be quickly configured to adapt as required due to changes.
Uptime organization
Heterarchies
Hierarchical organization
Social networked organization
Matrix organization
As a highly flexible structure, E: matrix organization can be quickly configured to adapt as required due to changes.
A matrix organization structure of is such a structure where teams report to multiple leaders. The matrix organization structure keeps open communication between teams and can help companies produce more innovative products and services. Using a matrix organization structure prevents teams from the need to realign every time a new project begins.
In the matrix organization design companies are divided into a hierarchy according to product or project teams. This structure is thought to be more flexible and conducive to adapting to changes quickly as required.
You can learn more about matrix organization at
https://brainly.com/question/7437866
#SPJ4
In which of the following practices does a business transfer all or part of its workforce to another firm, which handles all human-resource-realted activities and costs?
a)coemployment
b)outsourcing
c)employee leasing
d)whistle-blowing
Employee leasing is a practice in which a business transfers all or part of its workforce to another firm, which handles all human-resource-related activities and costs. This means that the leasing firm is responsible for:
PayrollEmployee benefitsOverall management of the staffWhich handles all Human-Resource-Realted activities and costs?Option C. Employee LeasingEmployee leasing can be beneficial to businesses who are looking to outsource their human resources functions. It can also help businesses save money on recruiting, training, and administrative costs. Additionally, it can give businesses access to a larger pool of talent and expertise. By outsourcing their human resources functions, businesses are able to focus on their core business activities.
Learn more about Employee Leasing: https://brainly.com/question/8975742
#SPJ4
an electrical load operates at 240 volts (rms). it absorbs an average power of 8kw at a lagging power factor of 0.8 (current lags voltage) calculate the complex power of the load calculate the impedance of the load, z
The impedance of the load 9.6 ohms. The complex power of the load is infinity.
The concept of complex power is important in bbecause it allows engineers to analyze the power flow in an AC electrical circuit, which is necessary for the design and operation of electrical power systems. It is also used in the analysis and optimization of power factor in electrical circuits.
The complex power of the load can be calculated using the following formula:
S = P + jQ
where P is the real power in watts, Q is the reactive power in volt-amperes reactive (VAR), and j is the imaginary unit.
To calculate the complex power of the load, we first need to calculate the reactive power. The reactive power can be calculated using the following formula:
Q = P x tan(θ)
where θ is the phase angle between the voltage and current. In this case, the phase angle is the angle between the voltage and the lagging current, which is 90 degrees. Therefore, the reactive power is:
Q = 8 kW x tan(90) = 8 kW x ∞ = ∞
The complex power of the load is then:
S = 8 kW + j x ∞
The impedance of the load can be calculated using the following formula:
Z = V / I
where V is the voltage and I is the current. In this case, the voltage is 240 volts and the current is:
I = P / (V x PF)
where P is the real power and PF is the power factor. Substituting the values, we get:
I = 8 kW / (240 V x 0.8) = 25 A
The impedance of the load is then:
Z = 240 V / 25 A = 9.6 ohms
Learn more about complex power, here https://brainly.com/question/2355649
#SPJ4
A sheet of glass 0.5 m wide and 18 mm thick is found to contain a number of surface cracks 3 mm deep and 10 mm long. If the glass is placed horizontally on two supports, calculate the maximum spacing of the supports to avoid fracture of the glass due to its own weight. For glass Kic0.3 MNm and density- 2600 kg/m'.
The maximum spacing of the supports to avoid fracture of the glass due to its own weight is 1.91m.
What is glass?Glass is a non-crystalline, frequently transparent, amorphous solid with many practical, technological, and decorative applications, such as in window panes, tableware, and optics. Some glasses, like volcanic glass, are produced naturally.
Glass is most frequently created by rapidly cooling (quenching) the molten form. The most well-known and historically most traditional varieties of manufactured glass are "silicate glasses," which are made from silica, which is the main chemical component of sand (also known as silicon dioxide or quartz).
Ninety percent of all glass produced is soda-lime glass, which has a silica content of around 70 percent. Despite the fact that silica-free glasses frequently have desirable qualities for applications in contemporary communications technology, the term glass is frequently only used to refer to this kind of material in everyday speech.
Learn more about glass
https://brainly.com/question/25775520
#SPJ4
write a comprehensive report on "7 habits of highly effective teens"
The comprehensive report on "7 habits of highly effective teens" is given below.
What are the 7 habits?The 7 Habits of Highly Effective Teens is a personal development book written by Sean Covey and published in 1998. It is based on the principles outlined in Stephen R. Covey's best-selling book The 7 Habits of Highly Effective People, and applies these principles to the unique challenges and opportunities faced by teenagers. The 7 habits are as follows:
Be proactive: Take responsibility for your actions and choices, and don't let external circumstances control your life.
Begin with the end in mind: Set clear goals and plan for the future, and make decisions that are aligned with your values and long-term vision.
Put first things first: Prioritize your tasks and responsibilities, and focus on what is most important and meaningful to you.
Think win-win: Seek mutually beneficial solutions in relationships and conflicts, and strive for cooperation and collaboration rather than competition.
Seek first to understand, then to be understood: Listen actively and empathetically to others, and try to see things from their perspective before expressing your own.
Synergize: Work effectively with others to achieve more than you could on your own, and value diversity and different perspectives.
Sharpen the saw: Take care of yourself physically, mentally, emotionally, and spiritually, and continually improve and grow as a person.
Therefore the 7 Habits of Highly Effective Teens is designed to help teenagers develop the skills and mindset needed to navigate the challenges of adolescence and become successful and effective adults.
Learn more about teens from
https://brainly.com/question/16352336
#SPJ1
use the phone's ports to daisy chain the pcs to the rest of the network. do not use the regular power outlets to power the phones. the list on the left displays several cable types and devices that may be required in this scenario. drag each cable type or device on the left to the corresponding location identified in the image. items on the left may be used more than once.
If an image for the matching location on the left is missing, the response will be arbitrary.
I want to daisy chain my phone and computer, but how?Connect a network cable to the phone's PC port before plugging the other end into the computer if you want to daisy-chain a computer to the phone. The connection to the computer should come from the phone (internet source > phone > computer).
Can two IP phones be connected to each other?Yes. Even when one phone doesn't have a regular phone account, you can connect two IP phones to the same network (LAN; it shouldn't be open to the internet since you'll get ghost calls) and call the other one by dialing its local IP address.
To know more about phones visit:-
https://brainly.com/question/19819920
#SPJ1
Which of the following cable types often includes a solid plastic core that keeps the twisted pairs separated?Cat 6Cat 3Cat 5eCat 5
The twisted pairs are kept apart in cat 6 cables by a solid plastic core, which also helps to prevent the cable from being bent too tightly.
Computer networks that can send data at speeds of one Gbps, 1000 Mbps, or more typically employ Cat 6 cables. The following traits apply: consists of four sets of copper wires, each of which is used in data transmission.
offers a speed of up to 10 Gbps, a bandwidth of 250 MHz, and a length that can be extended to 100 metres.
compares favourably to earlier twisted pair cable variants in terms of better crosstalk and attenuation protection.
Ethernet networks like 10BaseT, 100Base-TX, 1000 Base-T, and 10 GBase-T can use the Cat 6 cable.
Know more about Computer networks here:
https://brainly.com/question/13992507
#SPJ4
Two level sections of 40-m stations with center heights of 1.32 and 1.59 m in cut, base width 15 m, side slopes 1-1/2:1. Part A Compute Ve for the data given Express your answer to five significant figures. Ve m3
The total volume of the two sections of the station is 1988.8 m³.
To compute Ve, we need to calculate the volume of the two sections of the station.
Volume is an important physical property of objects and substances, and it is often used in various fields such as chemistry, physics, engineering, and biology. In chemistry, volume is used to measure the amount of a substance, such as a chemical element or compound.
The volume of a section of the station can be calculated using the formula:
Ve = (base width x center height x length) x (1 - (slope ratio / (1 + slope ratio)))
For the first section with a center height of 1.32 m and a base width of 15 m, the volume would be:
Ve = (15 m x 1.32 m x 40 m) x (1 - (1.5 / (1 + 1.5))) = 907.2 m³
For the second section with a center height of 1.59 m and a base width of 15 m, the volume would be:
Ve = (15 m x 1.59 m x 40 m) x (1 - (1.5 / (1 + 1.5))) = 1081.6 m³
The total volume of the two sections is the sum of the volume of each section, so the total volume is:
Ve = 907.2 m³ + 1081.6 m³ = 1988.8 m³
So the total volume of the two sections of the station is 1988.8 m³.
Learn more about volume, here https://brainly.com/question/1578538
#SPJ4
the impedance of tissue is 3 x 105 rayls and for the pzt crystal is 6 x 106 rayls. what is the best impedance for the matching layer?
The ideal impedance for the matching layer is 9.5 x 105.
Explain about the impedance of tissue?The ability of biological tissue to hinder (oppose) electrical current is known as bio impedance and is regarded as a passive electrical feature. A biological tissue's response to electric excitation (either current or voltage) supplied to it can be used to assess bio impedance.
In a number of organs, such as the breast, cervix, skin, bladder, and prostate, tissue electrical impedance, which is a function of the tissue's structure, can be used to distinguish between healthy and malignant tissues.
Silver electrodes are typically used to record the impedance of samples. Placing electrodes at either end of a cuboid or cylindrical sample of the tissue is the simplest configuration. The impedance is determined using the measured voltage and a steady current flow.
To learn more about impedance of tissue refer to:
https://brainly.com/question/13894673
#SPJ4
. the jet aircraft has a total mass of 22 mg and a center of mass at g. initially at takeoff the engines provide a thrust and . determine the acceleration of the plane and the normal reactions on the nose wheel at a and each of the two wing wheels located at b. neglect the mass of the wheels and, due to low velocity, neglect any lift caused by the wings.
Answer:
The acceleration of the plane is given by the equation a = F/m, where F is the thrust force and m is the mass of the plane. Therefore, the acceleration of the plane is given by a = F/22 kg.
The normal reaction on the nose wheel at A is given by the equation R_A = F + mg, where F is the thrust force and m is the mass of the plane. The normal reaction on the two wing wheels at B is given by the equation R_B = mg, where m is the mass of the plane. Therefore, the normal reaction on the nose wheel at A is given by R_A = F + 22 kg and the normal reaction on the two wing wheels at B is given by R_B = 22 kg.
Explanation:
You are working as a security administrator. Your enterprise has asked you to choose an access control scheme in which a user is authorized to access the resources if the user has a specific attribute and denied if they don't.Which of the following access control schemes should you choose?
Answer: Attribute-based access control
The access control scheme that could be used in order to authorize a user if he has a specific attribute and denied if they don't, then the access control scheme will be a) attribute-based access control.
In the field of computers and technology, attribute-based access control can be described as a control feature in which those users are authorized for access if they have a particular attribute. On the other hand, such users that do not have the particular attribute will not be granted access.
When working as a security administrator, attribute-based access control can be formulated by the administrator if he wants to give authorized access to certain users.
Although a part of your question is missing, you might be referring to this question:
You are working as a security administrator. Your enterprise has asked you to choose an access control scheme in which a user is authorized to access the resources if the user has a specific attribute and denied if they don't. Which of the following access control schemes should you choose?
a) Rule-based access control
b) attribute-based access control
c) ethernet-based access control
d) none of the above
To learn more about administrator, click here:
https://brainly.com/question/26096799
#SPJ4
the program segment below is intended to move a robot in a grid to a gray square. the program segment uses the procedure goalreached, which evaluates to true if the robot is in the gray square and evaluates to false otherwise. the robot in each grid is represented as a triangle and is initially facing left. the robot can move into a white or gray square but cannot move into a black region. a 15-line code segment reads as follows. line 1: repeat until, open parenthesis, goal reached, open parenthesis close parenthesis, close parenthesis. line 2: open brace. line 3: if, open parenthesis, can underscore move, open parenthesis, forward, close parenthesis, close parenthesis. line 4: open brace. line 5: move underscore forward, open parenthesis close parenthesis. line 6: close brace. line 7: if, open parenthesis, can underscore move, open parenthesis, right, close parenthesis, close parenthesis. line 8: open brace. line 9: rotate underscore right, open parenthesis close parenthesis. line 10: close brace. line 11: if, open parenthesis, can underscore move, open parenthesis, left, close parenthesis, close parenthesis. line 12: open brace. line 13: rotate underscore right, open parenthesis close parenthesis. line 14: close brace. line 15: close brace. for which of the following grids does the program not correctly move the robot to the gray square?
The correct answer is Although the program will not move the robot to the gray square in Grid II, it will correctly move the robot to the gray square in Grid I. This option is correct.
A simulation enables exploration of a phenomena without the time, safety, or financial constraints of the actual world. Both the first value and the second value are true. These industrial robots have three prismatic joints that slide along three perpendicular axes to produce linear motion (X, Y and Z). In order to provide rotational movement, they could additionally include an attached wrist.While the programme is running, values are entered using the input statement.Robots that do not have servo motors are used to position and move items. This implies that these robots will be able to pick up, transfer, and then set down objects.
To learn more about gray square click the link below:
brainly.com/question/29172488
#SPJ4
true or false: pre-civil war building technology included the first structural use of iron for buildings in the cast-iron fronts and building frames.
Cast-iron fronts and building frames represent the first structural application of iron for structures in pre-Civil War construction technology.
What is the pre-civil war building technology ?Cast-iron building fronts and frames were among the first structural uses of iron for structures in pre-Civil War construction. Cast-iron framing was a significant improvement in engineering and construction methods that made it possible to build taller, more intricate structures.Cast-iron frames were advantageous for offering fire protection as well as allowing for bigger windows and more interior light. Cast iron was a very rare and expensive material used for building frames before the industrial revolution.Iron became more widely available after the industrial revolution, allowing for quicker and more affordable building.Cast-iron frames also made it possible to erect taller buildings, which was a significant development in both urban design and engineering.Cast-iron frames and fronts made it possible to erect elaborate and beautiful facades, which grew to be a defining feature of many pre-Civil War structures.To learn more about the pre-civil war building technology refer to:
https://brainly.com/question/29520473
#SPJ4
If the parent isotope has a half-life that equals 1.75 million years, how old is the rock?
Choose one:
A. 0.86 Ma
B. 5.25 Ma
C. 3.50 Ma
D. 3.06 Ma
E. 1.75 Ma
If the parent isotope has a half-life that equals 1.75 million years, The rocks is 1.75 Ma. old
What is meant by isotope ?Atoms that have different numbers of neutrons but the same number of protons are called isotopes. They differ in mass, which affects their physical characteristics even if they have nearly identical chemical properties.
The name "isotope" refers to the fact that different isotopes of a single element occupy the same location on the periodic table. The term "isotope" is derived from the Greek words isos ("equal") and topos ("place"), which together indicate "the same place."
Atoms with varied proton numbers but the same neutron number are referred to as isotones.
Two atoms are different elements if they have differing quantities of protons. However, two atoms are said to be isotopes if they contain the same number of protons but differing numbers of neutrons. The words atomic number and mass number are used to describe nuclides (isotopes).
To learn more about isotope refer to :
brainly.com/question/14220416
#SPJ4
given the following instruction list and latencies, a reservation station with two loaders and one multiplier and one adder
Tomasulo's algorithm implements register renaming through the use of what are called reservation stations.
As soon as instruction operands become available, reservation stations act as buffers to retrieve and store them. Source operands can point to other reservation stations or the register file. Instead of having to wait for the data value to be saved in a register and reread, reservation stations allow the CPU to fetch and reuse a data value immediately after it has been calculated. They can choose the reservation station from which they wish their input to be read when instructions are given. In order to accommodate out-of-order and speculative instruction execution, the Tomasulo algorithm is extended with a hardware component known as a re-order buffer (ROB). The extension requires that commands be committed in the correct order.
To learn more about reservation stations click the link below:
brainly.com/question/27127828
#SPJ4
If drive wheel X rotates clockwise at a speed of 10 rpm , how does wheel y turn
We can determine how long it takes for anything to spin through a specific angular displacement by looking at its average angular velocity. The instantaneous angular velocity provides us with information about the rate of rotation of an object. Thus, option C is correct.
What role of Angular velocity in wheel transmission?The angular velocity of a wheel, for instance, is 120 radians per minute if it rotates 60 times in a minute.
A pair of wheels must always move at the same linear speed, regardless of the wheel transmission.
Angular velocity is equal to linear velocity divided by the circumference of the wheel (2×radius).
Radius (Y) / Radius = Angular Velocity (X) / Angular Velocity (Y) (X)
Therefore, : c/w faster The angular velocity of Y is greater than X because its radius is less than X's.
Learn more about Angular velocity here:
https://brainly.com/question/29557272
#SPJ1
created by congress as one of the major public-works projects of the new deal, this built a system of dams in the southeast.
TVA - Tennessee Valley Authority. Power companies fiercely opposed the TVA because they disliked the less expensive energy it offered and thought the agency posed a danger to free market.
A notched bar is broken in a pendulum-style impact tester to determine the ductile/brittle transition temperature for every specific steel sample. The energy absorbed during the fracture is then calculated. Steel 1045 specimens break apart when the temperature drops below zero and display brittle-like fracture (specimens 1 to 4 from -200oC to 0.0oC), however when the temperature rises, the specimens display ductile-like fracture (specimens 5 to 7 from 24oC to 100oC). Mild steel is malleable and ductile because it contains between 0.05 and 0.30 percent carbon. This steel has low carbon, with a carbon concentration of about 0.3%, making it neither overly brittle nor overly ductile. It is utilized practically everywhere since it is in the middle, which strikes a good balance. The Tennessee Valley Authority (TVA) is a U.S. electric utility company that is controlled by the federal government. All of Tennessee is included in TVA's service region, along with small portions of Georgia, North Carolina, Virginia, Alabama, and Mississippi. Despite being a governmental agency, TVA is run like a private for-profit business and does not receive any taxpayer money. Its headquarters are in Knoxville, Tennessee, and it is both the largest public utility and the sixth-largest power supplier in the nation.
Learn more about Tennessee Valley Authority here
https://brainly.com/question/2894133
#SPJ4
if you are designing a long-term retaining wall, which triaxial test should be used to determine the shear stress strength of the soil and why?
The soil's resistance to tangential (or shear) stress-induced deformation depends on its shear strength. More cohesion and friction or interlocking between the soil's particles will be present in soil with higher shear strength to stop the particles from sliding over one another. To determine bearing capacity and create retaining walls, slopes, and embankments, soil shear strength is used.
Deviatoric tension is elevated as a result (sigma 1 - sigma 3). The findings would point to a poorer soil (less shear strength than the actual shear strength of the soil). For any design project, it is essential for ground engineers to understand the shear strength of the soil. Everything that is constructed eventually comes into contact with the earth and transfers load there. The first stages in the design process are always to identify and measure the factors that affect a soil's strength. In this tutorial, we will first define and discuss the shear strength of soil and its significance before examining how groundwater and soil status affect shear strength of soil. We will then talk about soil shear strength tests and the method used to calculate them.
Learn more about shear strength here
https://brainly.com/question/22985582
#SPJ4
An ____ is a secure network that uses the Internet and Web technologies to connect intranets of business partners so communication between organizations is possible.
An extranet is a safe network that links the intranets of business partners so that there can be communication between the two enterprises. An extranet is a private network that organizations utilize to give dependable outside parties, such partners, customers, suppliers, and vendors, secure, restricted access to business data or processes.
What is intranet?
A private network website used within a company is known as an intranet. The same protocol as a web page is used by an intranet website. Using a broadband Internet connection in place of a traditional phone line, Voice over Internet Protocol is a technology that enables voice calls.
Both are employed in the exchange and network-based sharing of data, documents, files, and folders Both networks are accessible through browsers.
To learn more about extranet from given link from given link
brainly.com/question/13263185
#SPJ4
There are several decisions to be made regarding the construction of a new forensic workstation that will be dictated by the choice of system board. Which of the following are affected by the choice of system board? (Select all that apply)
CPU brand and speed
What OS can be installed
Whether or not RAID arrays can be used
The amount and type of memory that can be installed
It is uncommon in the IT industry for a technology that was created many years ago to be still in use and crucial for administrators and other users.
RAID (redundant array of independent discs) is a technique for protecting data in the event of a drive failure by storing the same data in several locations on numerous hard discs or solid-state drives (SSDs). The storage method known as RAID, or Redundant Array of Independent Disks, writes data across many discs in the same system. There is no need to utilise RAID as a foundation for an HDFS because HDFS handles fault tolerance and "striped" reading. RAID will just increase costs, provide less storage, and be slower (depending on the RAID levels).
To learn more about technology click the link below:
brainly.com/question/9171028
#SPJ4
a data warehouse contains data that covers a much longer time frame than a traditional transaction-oriented database would.
This is a true statement because a data warehouse contains data that covers a much longer time frame in comparison to a traditional transaction-oriented database.
The major difference between a data warehouse database and a transactional database is that the former is to be designed and optimized to respond to analysis questions that are critical for your business operations, and the latter is designed and optimized to maintain records.
The other difference to consider in comparison to these two types of databases is that data in a data warehouse has the ability to cover a much longer time frame as opposed to data in traditional transaction-oriented databases. It is because queries usually concern longer-term decision-making instead of daily transaction details.
"
Complete question:
a data warehouse contains data that covers a much longer time frame than a traditional transaction-oriented database would.
True
False
"
You can learn more about database at
https://brainly.com/question/518894
#SPJ4
the goal of one-shot learning is to find values for the weights wi using a large provided set of training data. once those weights have been found, they can be used to estimate prices for additional houses.
One-shot learning is an ML-based object classification algorithm that assesses the similarity and difference between two images. It's mainly used in computer vision.
One-shot learning aims to educate the model how to make its own inferences about the similarities between them based on the fewest possible pictures. One-shot learning is a common issue with object classification in computer vision. One-shot learning seeks to categorise things from one or a small number of instances, in contrast to the majority of machine learning-based object categorization algorithms that need training on hundreds or thousands of examples. When a machine is trained to learn from data without ever having to view the data itself, this process is known as zero-shot learning. Few-shot learning is the process of teaching a computer how to utilise data to learn from a particular perspective. A computer may be taught to learn from data using both zero-shot and few-shot learning techniques.
To learn more about One-shot learning click the link below:
brainly.com/question/29806553
#SPJ4
In order to perform a binary search on an array, which of the following must be true (select all that apply)?
a. The array must be ordered
b. The array must contain integers
c. The array must have an even number of elements
d. The array must have an odd number of elements
In order to perform a binary search on an array, the array must be ordered. Thus, option (A) is true regarding this statement.
Binary search is an efficient searching algorithm that finds an element from a sorted list of elements. Binary search functions by repeatedly dividing in half the portion of the list that could have the element, until it has been narrowed down the possible locations to just one. Binary search can only be implemented using an array of sorted values.
Therefore, the required condition to perform binary search on an array or list is that the array must be ordered or sorted.
You can learn more about binary search at
https://brainly.com/question/15190740
#SPJ4
which of the following instruments has one continuous cutting edge around the face because the two sides are united without interruption by the rounded toe?
D) Universal curet is the instrument that involves one continuous cutting edge around the face because that the two sides are united without interruption by the rounded toe.
Universal curettes are designed in a way that makes it possible to adapt one instrument to all tooth surfaces by enabling the use of both cutting edges on each blade. Universal curettes are particularly designed for the removal of moderate to heavy calculus from all supra- and subgingival tooth surfaces. Universal curettes types of instruments contain one continuous cutting edge around the face to make the two sides united without interruption by the rounded toe.
"
Complete question is:
which of the following instruments has one continuous cutting edge around the face because the two sides are united without interruption by the rounded toe?
A) Curved scaler
B) Sickle scaler
C) Straight scaler
D) Universal curet
E) Area-specific curet
"
You can learn more about dental instruments at
https://brainly.com/question/28783924
#SPJ4
Which of these is true for prototypes?
a. Horizontal Prototypes does some processing apart from the required for presenting the productâs user interface
b. Vertical Prototype realizes part or all of a productâs user interface
c. All of the mentioned
d. None of the mentioned
Answer:c
Explanation:
Company X recently detected some strange text
messages being sent between customers. They
believe that these coded text messages are in
support of criminal activities. They want to be able to
automate the detection and escalation of these
messages to help avoid crime. The text message
seems to be a string of random alphanumeric
characters followed by a symbol (the last three
characters of the text message), but on closer
identification they notice that there are palindromes
within the text that correlate to spurious activity. A
palindrome is a word, phrase, or sequence that
reads the same backward as forward.
The challenge is to identify these palindromes and
assign a score. What we have noticed is the
following:
• In their scenario, a valid palindrome is defined
as having three or more characters in sequence
and can overlap each other in the sequence.
When there are two or more palindromes a
threat should be detected.
• The score can be calculated as the sum of the
length of all valid palindromes.
The cardinality of the score can be measured as
follows:
• 1-10 - Possible
• 11-40 - Probable
11-40 - Probable
• 41-150 - Escalate
• Otherwise - Ignore
As an analyst, you have been tasked to take the text
messages presented and write a programme that will
predict what your manager should do.
Constraints
• 1
All text messages will be followed by a three
character symbol
The process of developing application programs is called program development. The five stages of program development are analysis, design, coding, debugging and testing, and maintaining application software.
This process is known as the program development life cycle (PDLC). Program policies, issue-specific policies, and system-specific policies are the three categories of security policies that are frequently used.
Application software is a class of computer programs that controls how well a certain computer use—or application—performs in order to satisfy end users' information processing requirements.
Technical, administrative, and physical security controls are the three basic categories of IT security measures.
Security controls are divided into three main categories. These include physical security controls as well as managerial security and operational security measures.
A program is a noun that refers to a collection of instructions that process input, manipulate data, and produce a result. It is also referred to as an application or software. As an illustration, the word processing tool Microsoft Word enables users to generate and write documents.
Know more about application here:
https://brainly.com/question/28650148
#SPJ4
in a dry type transformer, the size and operating temperature of the unit is determined by the type of?
Dry-type transformers, unlike liquid-filled counterparts, do not use liquid to dissipate excess heat and meet temperature classification requirements. The coils in a dry-type transformer, on the other hand, are made of a gaseous or dry insulation medium.
The following factors influence the unit's size and operating temperature:
Temperature ratings (i.e., ambient temperature, winding temperature, or temperature rise) are normally measured depending on the design of transformers. whether the transformer is dry or oil-immersed. The majority of the cases only contain oil-immersed transformers.
As a result, the temperature ratings can be identified by the transformers' cooling system. As a result, the dry type transformer contains an air natural or air forced (ANAF) system. We don't use oil for cooling here, so we can't use temperature measuring instruments like thermometers, oil temp indicators, or winding temp indicators. All of these are only suitable for oil insulating transformers.
To know more about Dry-type transformers, visit: https://brainly.com/question/29673808
#SPJ4
A man wishes to have $7500000 available in his bank account when his daughter's first year college expenses begin. how much must he deposit now at 3.5% compounded annually, if the girl is to start in college six years from now.
The amount of money which he must deposit now at 3.5% compounded annually is equal to $6,101,033.
How to determine the principal amount?Mathematically, compound interest can be calculated by using this formula:
A(t) = P(1 + r/n)^{nt}
Where:
A represents the future value.P represents the principal.r represents the interest rate.n represents the number of times compounded.T represents the time measured in years.Substituting the given parameters into the compound interest formula, we have the following;
7,500,000 = P(1 + 0.035)^{6}
7,500,000 = P(1.035)^{6}
7,500,000 = P(1.2293)
Principal, P = 7,500,000/1.2293
Principal, P = $6,101,033.
Read more on interest rate here: brainly.com/question/26343258
#SPJ1
Technician A says that a body-over-frame vehicle may have front upper rails.
Technician B says that a body-over-frame vehicle usually has the body welded to the frame.
Who is right?
A)
A only
B)
B only
C)
Both A and B
D) Neither A nor B
Control points are areas of the vehicle structure that are used to monitor the precision of the vehicle body's dimensions as they are being assembled. Thus, option B is correct.
What frame vehicle usually has the body welded?In a full frame car, the body is independent of the frame and fastened by bushings and bolts. The unibody is a structure made up of integrated panels that are welded, bonded, and riveted together.
Therefore, In a full frame car, the body is independent of the frame and fastened by bushings and bolts. The unibody is a structure made up of integrated panels that are welded, bonded, and riveted together.
Learn more about welded here:
https://brainly.com/question/18667026
#SPJ1