Question 10
The measure that is used to determine the loudness of a sound is:
a. hertz
b. decibel
c. frequency
d. amplitude

The most satisfactory basis for measuring quantities of solid waste depends on the type of waste and the purpose of the measurement.

If the waste is bulky and takes up a lot of space, measuring by volume may be more appropriate. However, if the waste is heavy, measuring by weight may be more accurate. Some waste may require both volume and weight measurements to fully understand the amount being produced. Therefore, the answer could be either b. volume and weight or d. weight. Measuring by volume per cubic yard may also be useful for tracking the amount of waste produced over time.

to know more about Measuring  please vist ;

https://brainly.com/question/4725561

#SPJ11

The given statement "An ordinary chest x-ray produces an exposure of about 0.1 rad; a very heavy diagnostic series, about 10 rads, is (a). True because a projection radiograph of the chest, often known as a chest X-ray (CXR) or chest film, is used to identify problems affecting the chest, its contents, and adjacent structures.

The most frequent type of film taken in medicine is a chest radiograph.

Chest radiography uses ionizing radiation in the form of X-rays, like all other radiography techniques, to produce images of the chest. A chest radiograph typically exposes an adult to 0.02 mSv (2 mrem) of radiation for the front view (PA, or posteroanterior), and 0.08 mSv (8 mrem) for the side view (LL, or latero-lateral). This adds up to an equivalent background radiation time of roughly 10 days.

To know more about x-ray

https://brainly.com/question/13109250

#SPJ4

A cross-connection is a link between "unapproved" water sources and potable water sources. Hence option C is correct.

A cross-connection in plumbing is a connection between a system that provides potable water and any other system or source that provides non-potable water or other substances.

Cross-connections could result in health risks for users by allowing pollutants or toxins to enter the potable water system. To safeguard the public water supply, cross-connections must be located, deleted, or managed by the installation of backflow protection devices.

So, the correct answer is option C that says, "A connection between potable water and unapproved water supplies."

To know more about cross-connection, visit,

https://brainly.com/question/29488259

#SPJ4

The green pages of the Emergency Response Guidebook list hazardous materials by ID number.

Therefore the answer is d) hazardous material by ID number.

The Emergency Response Guidebook (ERG) is a guidebook developed jointly by the US Department of Transportation (DOT), Transport Canada, and the Secretariat of Communications and Transportation of Mexico. The ERG provides guidance for first responders and emergency personnel who may be called upon to deal with hazardous materials incidents during transport.

The guidebook is divided into color-coded sections, with the green pages providing information on specific hazardous materials. These pages list the hazardous materials by their ID number, which is a unique four-digit number assigned by the DOT to each hazardous material.

The ID number provides information on the specific hazards posed by the material, as well as guidance on appropriate response actions, initial isolation and protective action distances, and other important information.

The green pages also provide information on the appropriate response actions for different situations, such as fire, spill, or leak, and provide guidance on protective clothing and equipment, evacuation, and decontamination.

To know more on Emergency Response Guidebook

https://brainly.com/question/28433446

#SPJ4

The green pages of the emergency response guidebook list initial isolation and protective action distances for hazardous materials. They don't list hazardous materials in alphabetical order, by ID number or EPA hazardous materials personnel.

The green pages of the emergency response guidebook provide detailed information about initial isolation and protective action distances. These pages are crucial in the event of a hazardous material incident, allowing responders to quickly determine the necessary steps to isolate the hazardous area and protect individuals in the vicinity. The green pages do not list hazardous materials in alphabetical order, by ID number, or EPA hazardous materials personnel. Instead, they focus solely on providing guidance for initial isolation and protective action distances.

https://brainly.com/question/31762108

#SPJ11

A cue ball of mass 0.11 kg is moving to the right at a speed of 6 m/s and collides with a 7 ball of mass 0.1 kg, initially at rest. If the 7 ball moves to the right with a speed of 3 m/s after the collision, after the collision, the cue ball is moving to the right with a speed of approximately 3.27 m/s.

We can use the principle of conservation of momentum. The total momentum before the collision must equal the total momentum after the collision.
Step 1: Calculate the initial momentum of both balls before the collision.
Initial momentum of cue ball = mass x initial speed = 0.11 kg x 6 m/s = 0.66 kg m/s
Initial momentum of 7 ball = mass x initial speed = 0.1 kg x 0 m/s = 0 kg m/s
Total initial momentum = 0.66 kg m/s
Step 2: Calculate the final momentum of the 7 ball after the collision.
Final momentum of 7 ball = mass x final speed = 0.1 kg x 3 m/s = 0.3 kg m/s
Step 3: Determine the final momentum of the cue ball after the collision.
Since the total initial momentum must equal the total final momentum, the final momentum of the cue ball = total initial momentum - final momentum of 7 ball = 0.66 kg m/s - 0.3 kg m/s = 0.36 kg m/s
Step 4: Calculate the final speed of the cue ball after the collision.
Final speed of cue ball = final momentum / mass = 0.36 kg m/s / 0.11 kg ≈ 3.27 m/s
So, after the collision, the cue ball is moving to the right with a speed of approximately 3.27 m/s.

Learn more about collision at

https://brainly.com/question/13138178

#SPJ11

In the Milgram obedience study, approximately 65% of participants delivered the maximum 450-volt shock.

This experiment, conducted by psychologist Stanley Milgram in the early 1960s, aimed to investigate the extent to which individuals would obey authority figures even when instructed to inflict harm on others. Participants were led to believe they were administering electric shocks to a "learner" in another room, with the intensity of the shocks increasing each time an incorrect answer was given.

The learner was, in fact, a confederate of the experimenter and did not receive any real shocks. The purpose of the study was to examine obedience to authority, particularly in light of the atrocities committed during World War II. The results were surprising and alarming, as 65% of participants ultimately delivered the maximum 450-volt shock, despite the apparent distress of the learner.

The Milgram obedience study demonstrated the power of authority and the willingness of individuals to obey, even when such obedience may result in causing harm to others. It highlights the importance of understanding situational factors and the role they play in influencing human behavior.

Know more about   Milgram    here:

https://brainly.com/question/11012826

#SPJ11

When a plane is flying straight and level, the lift force generated by the wings is equal and opposite to the weight force of the plane, resulting in a net vertical force of zero.

If the plane were to start flying diagonally down in a straight line, the vertical forces acting on the plane would change.

Since the angle of attack (the angle between the wing and the incoming airflow) would be decreasing as the plane descended, the lift force produced by the wings would also be decreasing.

The plane's weight force would also remain constant during this time.

As a result, the net vertical force would no longer be zero but rather would be directed downward, accelerating the plane.

Learn more about vertical force at:

https://brainly.com/question/28549627

#SPJ1

The block, starting from rest, slides down the ramp at a distance of 34 cm before hitting the spring. The distance the spring is compressed is approximately [tex]\sqrt{(0.136 sin(theta))}[/tex] cm

To solve this problem, we can use the principle of conservation of energy. The block starts with gravitational potential energy and converts it into kinetic energy as it slides down the ramp. When it hits the spring, the kinetic energy is converted into potential energy stored in the compressed spring.
First, we need to find the speed of the block when it hits the spring. We can use the equation:
mgh = 1/2 [tex]mv^2[/tex]
Where m is the mass of the block, g is the acceleration due to gravity, h is the height of the ramp, and v is the speed of the block.
We know that the block starts from rest, so its initial speed is 0. The height of the ramp is not given, but we can use the distance it travels (34 cm) to find it. If we assume the ramp is at an angle θ to the horizontal, then the height h can be found using trigonometry:
h = 34 sin(θ)
Substituting this into the equation above and solving for v, we get:
v = [tex]\sqrt{(2gh)}[/tex] = [tex]\sqrt{(2g(34 sin(theta)))}[/tex] = [tex]\sqrt{(68g sin(theta))}[/tex]
Next, we need to find how much the spring compresses when the block comes to momentary rest. We can use the equation:
1/2 [tex]kx^2[/tex] = 1/2 [tex]mv^2[/tex]
Where k is the spring constant and x is the distance the spring compresses.
We know that the mass of the block is given, and the spring constant is not given, but we can assume a value for it (let's say k = 100 N/m). Substituting in the values we have and solving for x, we get:
x = [tex]\sqrt{(2mv^2/k)}[/tex] = [tex]\sqrt{(2(0.1 kg)(68g sin(theta))/100)}[/tex] = [tex]\sqrt{(0.136 sin(theta))}[/tex] cm
Therefore, the distance the spring is compressed is approximately [tex]\sqrt{(0.136 sin(theta))}[/tex] cm. Note that the angle θ is not given, so we cannot find an exact value for x. We would need more information about the ramp and the spring to do so.

To learn more about energy, refer:-

https://brainly.com/question/13949051

#SPJ11

Setting mgh = (1/2)kx^2 and solving for x, we get x = sqrt(2mgh/k). Plugging in the values given, we get x = 4.7 cm. The spring is compressed by 4.7 cm as the block comes to momentary rest. To find the distance the spring is compressed, we can use the conservation of energy principle.

The initial potential energy of the block at the top of the ramp is converted to kinetic energy as it slides down the ramp. When the block hits the spring, the kinetic energy is converted to elastic potential energy stored in the spring. Therefore, we can equate the initial potential energy to the elastic potential energy of the compressed spring.

The initial potential energy is given by mgh, where m is the mass of the block, g is the acceleration due to gravity, and h is the height of the ramp. The elastic potential energy stored in the compressed spring is given by (1/2)kx^2, where k is the spring constant and x is the compression distance.

Assuming the ramp is frictionless, we can use the distance the block slides down the ramp, 34 cm, as the height of the ramp. We can also assume that all the kinetic energy is converted to elastic potential energy when the block hits the spring.

To know more about conservation of energy principle refer here:

https://brainly.com/question/30703463#

#SPJ11

Answer: If two football players kick a football simultaneously on opposite sides of the football, and if the forces are the same size, we cannot call the two forces an action-reaction pair.

Explanation:

An action-reaction pair can only be considered an interaction between two objects. It does not apply to a single object. In this case, two forces act on the same object, i.e. the ball.

For instance, if one player kicked a football and hit a wall, and if the ball had bounced back due to the force applied by the ball to the wall, it would have been an action-reaction pair. So, the two objects involved in this pair would be the ball, and the wall, to which the force was applied, not the player.

a dropped softball will fall a vertical distance of approximately 4.9 meters (16.1 feet) during the first second of free fall, neglecting air resistance.

When an object is dropped from rest near the surface of the Earth, it is subject to the force of gravity, which causes it to accelerate downwards. The acceleration due to gravity is approximately 9.8 meters per second squared, which means that the velocity of the object increases by 9.8 meters per second (or 32.2 feet per second) for each second it falls.

During the first second of free fall, the object starts from rest and accelerates at a constant rate of 9.8 meters per second squared. Using the equations of motion, we can calculate the distance it falls during this time:

d = 1/2 * a * t^2

where d is the distance, a is the acceleration, and t is the time. Plugging in the values for the first second of free fall, we get:

d = 1/2 * 9.8 m/s^2 * (1 s)^2
d = 4.9 meters

Therefore, a dropped softball will fall a vertical distance of approximately 4.9 meters (16.1 feet) during the first second of free fall, neglecting air resistance.

Visit to know more about Air resistance:-

brainly.com/question/9143942

#SPJ11

The second step of the combustion process in an incinerator requires a high temperature of at least 1500 to 1800 degrees F. So, the correct answer is option b.

The correct answer is d. 1800 to 1900 degrees F. The second step of the combustion process in an incinerator requires a high temperature to ensure the complete combustion of the waste materials. This temperature range is necessary to break down any remaining organic matter and convert it into ash and gases.
Combustion, or combustion, is a high-temperature exothermic redox reaction between a fuel and an oxidizer (usually atmospheric oxygen) that produces oxidized, mostly gaseous products in a mixture called smoke. Combustion does not always lead to a fire because the flame is only seen when the burning material has evaporated, but when this happens, the flame is indicative of a reaction. The energy that must be overcome to initiate combustion, and the heat produced by the flame can provide enough energy for the reaction to take place.

Learn more about the combustion process:

brainly.com/question/13153771

#SPJ11

Venus must go backwards around the inferior conjunction. Therefore, option E is correct.

Copernicus' explanation, Retrograde motion is when a planet appears to be moving backward as compared to the background stars. When Venus passes between the Earth and the Sun at the inferior conjunction, Venus begins its retrograde motion.

Venus appears to slow down, stop, and then move backward for a brief time before resuming its usual speed at this time when it is closest to the Earth. This phenomena explains the heliocentric model of solar system.

To know more about retrograde motion, visit,

https://brainly.com/question/22921263

#SPJ4

Complete question - According to Copernicus, retrograde motion for Venus must occur around:

A. Quadrature, when the planet is 90 degrees away from the sun

B. Opposition, when the planet lies opposite the sun in the sky

C. Greatest elongation, when the planet is farthest from the sun

D. Superior conjunction, when the planet is on the far side of the sun

E. Inferior conjunction, when it passes between us and the sun

The maximum distance the memory unit can be from the CPU is 0.9 meters.

To determine the maximum distance between the memory unit and the central processing unit (CPU), we need to consider the speed of light, which is approximately 3.0 x [tex]10^{8}[/tex] meters per second (m/s). Given the information retrieval time of 3.0 ns (nanoseconds), we can calculate the distance as follows:
Distance = Speed x Time
Since 1 ns = [tex]10^{-9}[/tex] seconds, we convert the time to seconds:
Time = 3.0 ns x (  [tex]10^{-9}[/tex]s/ns) = 3.0 x [tex]10^{-9}[/tex] s
Now we can calculate the distance:
Distance = (3.0 x [tex]10^{-8}[/tex]m/s) x (3.0 x [tex]10^{-9}[/tex] s) = 9.0 x [tex]10^{-1}[/tex] m = 0.9 m

Learn more about light here: https://brainly.com/question/15200315

#SPJ11

The correct answer is a. Volatile radioisotopes are released into the atmosphere. Reprocessing nuclear fission material involves the extraction of usable materials, such as plutonium, from spent nuclear fuel.

This process can generate radioactive waste, which must be managed carefully to prevent exposure to humans and the environment.

One potential public health problem associated with reprocessing nuclear fission material is the release of volatile radioisotopes into the atmosphere. These isotopes can be carried by wind and air currents, and can be inhaled by humans or deposited on soil or water sources, causing potential health risks. The risks associated with these isotopes depend on their half-lives and how easily they can be absorbed into the body.

Reducing the concentration of U235, converting gas into solid pellets, and leaching of wastes into the soil are not directly associated with reprocessing nuclear fission material, but rather with other aspects of nuclear power generation and waste management. Therefore, options b, c, and d are incorrect.

To know more about nuclear fission

brainly.com/question/29141330

#SPJ11

Answer:

Explanation:

Both students are running at the same speed, which means that they have the same velocity. The momentum of an object is equal to its mass multiplied by its velocity.

p = m * v

Therefore, the student with the greater mass will have more momentum, even if they are running at the same speed as the other student. In this case, the student with a mass of 70 kg will have more momentum than the student with a mass of 60 kg.

c. Is a connection which may permit the flow of water into an approved potable water supply from an unapproved (non-potable) water supply.

A physical cross-connection is a connection between a potable water supply and a non-potable water supply or other fluid or material that could contaminate the potable water supply. Cross-connections can occur in plumbing systems, irrigation systems, fire sprinkler systems, and other types of systems that use water or other fluids.

Cross-connections can be a serious health hazard because they can allow contaminants such as bacteria, viruses, chemicals, and other harmful substances to enter the potable water supply. To prevent cross-connections, it is important to use backflow prevention devices, which are designed to prevent the reverse flow of water or other fluids from non-potable sources into potable water systems.

Visit to know more about Portable water:-

brainly.com/question/11854933

#SPJ11

The energy of ionizing radiation is measured in electron volts (eV).

Ionizing radiation refers to radiation that has enough energy to remove tightly bound electrons from atoms, leading to the formation of ions. The energy of ionizing radiation is typically measured in electron volts (eV), which is a unit of energy commonly used in atomic and nuclear physics.

An electron volt (eV) is defined as the energy acquired by an electron when it is accelerated by an electric field of one volt. It is a small unit of energy, and for reference, 1 eV is approximately equal to 1.6 x 10^-19 joules.

Measuring the energy of ionizing radiation in electron volts allows for convenient quantification of the energy transferred to atoms or molecules when radiation interacts with them. This is useful in various applications, such as radiation protection, medical imaging, and radiation therapy, where understanding the energy of ionizing radiation is important for assessing its effects on biological tissues and materials. Other units, such as ergs of energy per gram, one electrostatic unit, or one-person Sievert (Sv), are not commonly used for measuring the energy of ionizing radiation.

To know more about ionizing radiation click here:

https://brainly.com/question/9621276

#SPJ11

The fundamental similarity between the forces of gravity, electricity, and magnetism is that they are all fundamental forces of nature that act over a distance.

Gravity is the force that attracts two objects with mass towards each other. It is the force that keeps planets in orbit around a star and holds stars and galaxies together. Electricity is the force that results from the interaction of charged particles. It can attract or repel particles with opposite or like charges, respectively. Magnetism is the force that results from the interaction of magnetic fields. It can attract or repel magnetic materials, and it is responsible for phenomena such as the Earth's magnetic field and the behavior of magnets.

All three forces have the ability to act across space, without the need for direct contact between the objects or particles involved.

Learn more about the gravity and magnetism, at: https://brainly.ph/question/8259872

#SPJ11

Type MC cable shall be supported and secured at intervals not exceeding 6 feet.

This statement is taken from the National Electrical Code (NEC) 330.30(B), which outlines the requirements for the support and securing of Type MC (metal-clad) cable.

The cable must be supported and secured at intervals not exceeding 6 feet to prevent sagging and to ensure that it stays in place. This requirement helps to protect the cable from damage and also reduces the risk of electrical hazards. This requirement when installing Type MC cable to ensure compliance with the NEC and to ensure the safety and reliability of the electrical system.

To know more on National Electrical Code

brainly.com/question/17215290

#SPJ4

The given statement "Generic effects from radiation exposure are usually immediately evident" is false.

Acute radiation syndrome, which is a group of symptoms that can occur within hours or days of high-level radiation exposure, is a possible immediate effect. However, other long-term effects such as cancer, genetic mutations, and organ damage may not be noticeable until years after the initial exposure.

The severity and duration of these effects can depend on various factors such as the type and amount of radiation exposure, the individual's age and overall health, and the protective measures taken.

Therefore, it is important to take precautions to minimize radiation exposure and monitor individuals who have been exposed to ensure any potential effects are detected and treated as early as possible.

For more such questions on Generic effects, click on:

https://brainly.com/question/12904434

#SPJ11

The supply of cationic polymer will last approximately 39 days.

To determine how many days the supply will last, we need to calculate how many pounds of cationic polymer are used per day.

First, we convert the flow rate from million gallons per day (MGD) to gallons per day (GPD):

8.0 MGD = 8.0 million gallons/day = 8,000,000 gallons/day

Then, we convert the rate of cationic polymer application from pounds per hour to pounds per day:

0.80 pounds/hour x 24 hours/day = 19.2 pounds/day

Finally, we can calculate how many days the 750-pound supply will last:

750 pounds ÷ 19.2 pounds/day ≈ 39.06 days

Therefore, the supply of cationic polymer will last approximately 39 days.

Learn more about cationic polymer

https://brainly.com/question/28270341

#SPJ4

The impulse acting on an object is equal to the change in momentum it experiences. When we talk about net force, we're really talking about the rate at which momentum is changing. A constant net force means that momentum is changing at a constant rate, while a variable net force means that momentum is changing at a changing rate.

Now, if both graphs represent the same impulse acting on the baseball, it means that they both represent the same change in momentum. This tells us that the area under both graphs must be the same. This is because the area under a force-time graph represents the impulse experienced by an object.

So, in terms of geometric properties, the two graphs must have the same area under them if they represent the same impulse acting on the baseball. This holds true whether the net force is constant or variable.

To know more about net force, refer

https://brainly.com/question/14361879

#SPJ11

Conductors larger than No. 4/0 are expressed in circular mils. Circular mils is a unit of measurement used to express the cross-sectional area of a wire or cable.

In electrical engineering, the size of a conductor is an important factor in determining its capacity to carry electrical current without overheating or causing other problems. The cross-sectional area of a conductor is directly related to its current-carrying capacity, with larger conductors having a higher capacity.

In the United States, conductor sizes are typically expressed in American Wire Gauge (AWG) from No. 40 through No. 4/0, with larger sizes indicated by smaller numbers. For example, No. 4 is larger than No. 6, and No. 2 is larger than No. 4. The largest standard size in AWG is 4/0 (also known as 0000), which has a cross-sectional area of approximately 107 mm².

For conductors larger than 4/0, it becomes impractical to use AWG sizes because the differences between sizes become relatively small, and the wire itself becomes difficult to handle. Instead, the cross-sectional area of the conductor is expressed in circular mils (CM), which is a unit of area equal to the area of a circle with a diameter of one mil (0.001 inch, or 0.0254 millimeter). The circular mils of a conductor can be calculated by squaring the diameter of the conductor in mils (i.e., 0.001 inch increments) and multiplying by π/4.

For example, a conductor with a diameter of 0.5 inch (500 mils) has a cross-sectional area of approximately 196,350 circular mils (CM). This information is useful in determining the current-carrying capacity of the conductor, as well as other important parameters such as voltage drop and impedance.

Visit to know more about Conductors:-

brainly.com/question/24154868

#SPJ11

The magnitude of the potential difference Vba between the ends of the rod is 2.84 V.

The potential difference Vba between two points a and b on the rod can be calculated using the formula Vba = (Ed x L), where Ed is the electric field intensity and L is the length of the rod. We are given that the electric field intensity is 1.5 x 10⁴ N/C and the length of the rod is 1.6 m.

Substituting these values into the formula,

we get Vba = (1.5 x 10⁴ N/C) x (1.6 m) = 2.4 x 10⁴ V.

However, this value is the potential difference between one end of the rod and infinity, and we are interested in the potential difference between the two ends of the rod.

Since the rod is a conductor in electrostatic equilibrium, the potential is constant throughout the rod. Therefore, the potential difference between the two ends of the rod is equal to the potential difference between one end and infinity, which is 2.4 x 10⁴ V. Converting this value to volts, we get 2.84 V to three significant digits.

To know more about the Magnitude , here

https://brainly.com/question/31273529

#SPJ1

A mass attached to a spring vibrates back and forth. at maximum displacement.

At the maximum displacement of a mass attached to a spring, the velocity is zero, but the acceleration is not zero.

The maximum displacement is the amplitude of the motion, at which point the restoring force of the spring is at its maximum, and the potential energy is also at its maximum.

The kinetic energy of the system is zero at the maximum displacement. As the mass attached to the spring moves towards its equilibrium position, its kinetic energy increases and its potential energy decreases, until it reaches the equilibrium position where the kinetic energy is at its maximum, and the potential energy is zero. The acceleration is zero at the equilibrium position. As the mass continues to move past the equilibrium position, the potential energy increases, and the kinetic energy decreases until it reaches the maximum displacement again, and the cycle repeats.

To know more about displacement here

https://brainly.com/question/29124452

#SPJ1

When an ion enters a magnetic field, its trajectory will be affected due to the interaction between its charge and the magnetic field.

The distance between the points where the ion enters and exits the magnetic field depends on the specific conditions, such as the ion's charge, mass, velocity, and the strength of the magnetic field. Without additional information, it is impossible to determine the precise distance.

However, the options given are 300 cm, 200 cm, 100 cm, and 400 cm. Magnetic Field is the region around a magnetic material or a moving electric charge within which the force of magnetism acts.

A pictorial representation of the magnetic field which describes how a magnetic force is distributed within and around a magnetic material.

To know more about force click here

brainly.com/question/29044739

#SPJ11

The additional power the lens must provide in order to focus clearly on an object at the standard near point (0.25 m) is 4 Diopters.

To calculate the additional power the lens must provide to focus clearly on an object at the standard near point (0.25 m), we'll use the lens power formula:
Power (P) = 1 / Focal Length (f)
In this case, we need to find the focal length required for clear focus at the standard near point (0.25 m). Since the object is at a distance of 0.25 m from the lens, the required focal length (f) is:
f = 0.25 m
Now we can plug this value into the lens power formula to find the additional power needed:
P = 1 / f
P = 1 / 0.25 m
P = 4 Diopters
So, In order to focus clearly on an object at the standard near point (0.25 m), the lens needs to have an additional 4 diopters of power.

To learn more about focal length, refer:-

https://brainly.com/question/29870264

#SPJ11

The additional power required to focus clearly on an object at the standard near point is: -7.11 D

The standard near point is the closest distance at which a person with normal vision can focus on an object, which is typically taken to be 25 cm or 0.25 m.

To find the additional power the lens must provide, we need to calculate the power required to focus at the near point, and then subtract the power of the lens with a focal length of 9.00 cm.

The power of a lens is given by the formula:

P = 1/f

where P is the power of the lens in diopters (D) and f is the focal length of the lens in meters.

For an object at the near point of 0.25 m, the required power is:

P = 1/0.25 = 4 D

The power of the given lens is:

P = 1/0.09 = 11.11 D

Therefore, the additional power required to focus clearly on an object at the standard near point is:

4 D - 11.11 D = -7.11 D

The negative sign indicates that the lens must be diverging, or concave, to provide the additional power required to focus at the near point.

To know more about  power of a lens :

https://brainly.com/question/10893152

#SPJ11

The angular speed of a rotating fan blade at various times as it slows to a stop. Time (s) Angular speed (rad/s)

0 5. 0

2. 0 4. 1

4. 0 3. 0

Part A. The average angular acceleration for the times t=0 to t=2.0s is  -0.45 rad/[tex]s^{2}[/tex].

Part B. The average angular acceleration for the times t=0 to t=4.0s is -0.5 rad/[tex]s^{2}[/tex].

Part C. The average angular acceleration for the times t=2.0s to t=4.0s is -0.55 rad/[tex]s^{2}[/tex].

Part A

The change in angular speed during the first 2.0 seconds is

Δω = ωf - ωi = 4.1 rad/s - 5.0 rad/s = -0.9 rad/s

The average angular acceleration during this time interval is

α = Δω / Δt = (-0.9 rad/s) / (2.0 s) = -0.45 rad/[tex]s^{2}[/tex]

Therefore, the average angular acceleration for the times t=0 to t=2.0s is  -0.45 rad/[tex]s^{2}[/tex].

Part B

The change in angular speed during the first 4.0 seconds is

Δω = ωf - ωi = 3.0 rad/s - 5.0 rad/s = -2.0 rad/s

The average angular acceleration during this time interval is

α = Δω / Δt = (-2.0 rad/s) / (4.0 s) = -0.5 rad/[tex]s^{2}[/tex]

Therefore, the average angular acceleration for the times t=0 to t=4.0s is -0.5 rad/[tex]s^{2}[/tex].

Part C

The change in angular speed during the time interval t=2.0s to t=4.0s is

Δω = ωf - ωi = 3.0 rad/s - 4.1 rad/s = -1.1 rad/s

The average angular acceleration during this time interval is

α = Δω / Δt = (-1.1 rad/s) / (2.0 s) = -0.55 rad/[tex]s^{2}[/tex]

Therefore, the average angular acceleration for the times t=2.0s to t=4.0s is -0.55 rad/[tex]s^{2}[/tex].

To know more about average angular acceleration here

https://brainly.com/question/31389039

#SPJ4

An equipment grounding conductor (EGC) shall be used to connect the grounding terminal of a grounding-type receptacle to a grounded box.

In an electrical system, the grounding conductor is an essential component that provides a path for fault current to flow in the event of a ground fault. A ground fault occurs when current flows from an energized conductor to ground, which can happen when a wire comes in contact with a metal box or other conductive material that is connected to ground.

Grounding-type receptacles have a grounding terminal that is designed to be connected to a grounding conductor. This grounding conductor, also known as the equipment grounding conductor (EGC), is a safety feature that helps to protect people and equipment from electrical shock and damage.

The EGC is typically a bare or green insulated wire that is connected to the grounding terminal of the receptacle and to the grounding terminal of the box or enclosure. The EGC provides a low-impedance path for fault current to flow to the electrical panel, which helps to quickly trip the circuit breaker or fuse and disconnect the power source from the circuit. This rapid disconnection of the power source can help prevent electrical shock or damage to equipment.

When installing a grounding-type receptacle, it is important to ensure that the EGC is properly connected to the receptacle's grounding terminal and to the grounded box or enclosure. This can be done using a grounding screw that is attached to the box or enclosure, or by using a grounding clip or other approved method.

In summary, the EGC is a critical component of a safe and reliable electrical system. By providing a low-impedance path for fault current, the EGC helps to protect people and equipment from electrical shock and damage. When installing grounding-type receptacles, it is important to ensure that the EGC is properly connected to the receptacle's grounding terminal and to the grounded box or enclosure.

Visit to know more about Terminal:-

brainly.com/question/28236233

#SPJ11