Initially, a single capacitance C1 is wired to a battery. Then capacitance C2 is added in parallel. Are (a) the potential difference across C1 and (b) the charge q1 on C1 now more than, less than, or the same as previously? (c) Is the equivalent capacitance C12 of C1 and C2 more than, less than, or equal to C1? (d) Is the charge stored on C1 and C2 together more than, less than, or equal to the charge stored previously on C1? (e)Repeat Question 5 for C2 added in series rather than in parallel. i only care for e part and please with the full answer so i can understand why

The energy added to accomplish the transformation of the ice cube was 18,828 J. To calculate the energy added to transform the ice cube, we need to use the formula Q = m * ΔT * C, where Q is the energy added, m is the mass of the substance, ΔT is the change in temperature, and C is the specific heat capacity.

First, we need to find the energy required to melt the ice cube, which is Q = 55g * (0∘C - 0∘C) * 333 J/g⋅∘C = 0 J.

Next, we need to find the energy required to heat the water from 0∘C to 100∘C, which is Q = 45g * (100∘C - 0∘C) * 4.184 J/g⋅∘C = 18,828 J.

Finally, we need to find the energy required to vaporize 10g of water at 100∘C, which is Q = 10g * (100∘C - 100∘C) * 2,257 J/g = 0 J.

Adding all of the energy requirements together, we get:

0 J + 18,828 J + 0 J = 18,828 J.

To know more about energy refer here:

https://brainly.com/question/1932868#

#SPJ11

To store 1.60 j of energy, the capacitor of 0.600 μf must be charged to a potential of 2.31 kV.

To find the potential needed to charge a 0.600 μF capacitor to store 1.60 J of energy, we can use the formula for the energy stored in a capacitor:

Energy (E) = (1/2) × Capacitance (C) × Voltage^2 (V²)

We are given the energy (E = 1.60 J) and the capacitance (C = 0.600 μF), and we need to find the voltage (V).

1. Rearrange the formula to solve for V:

V² = (2 × E) / C

2. Plug in the given values:
V² = (2 × 1.60 J) / (0.600 μF)

3. Calculate the result:
V² = 5.333... (rounded to the nearest thousandth)

4. Take the square root of both sides to find V:
V = √5.333...

5. Calculate the final value for V:
V = 2.31 kV (rounded to the nearest hundredth)

So, you should charge the 0.600 μF capacitor to a potential of 2.31 kV to store 1.60 J of energy.

Learn more about capacitor:

https://brainly.com/question/27393410

#SPJ11

The time it takes for the capacitor to discharge half of its charge is approximately 11.7 seconds.

The time constant of an RC circuit, denoted by τ, is given by the expression: τ = RC. where R is the resistance in ohms, and C is the capacitance in farads.

In this case, the capacitor is wired in series with a resistor of 8 ohms, and we are given the charge q on the capacitor. We can use the formula for the capacitance of a capacitor to determine its value: C = q/V

where V is the voltage across the capacitor. Since the capacitor is fully charged, the voltage across it is the maximum voltage that it can hold, which is determined by the capacitance and the charge: V = q/C

Substituting the given values, we get:

V = (7.5×10⁻⁵ C)/(C)

Solving for C, we get:

C = (7.5×10⁻⁵ C)/(V)

Substituting this value of C and the given resistance value into the expression for τ, we get:vτ = RC = (8 Ω)(7.5×10⁻⁵ C)/(V)

τ = (8 Ω)(7.5×10⁻⁵ s)/C

To determine the time it takes for the capacitor to discharge half of its charge, we can use the formula for the charge on a capacitor as a function of time in an RC circuit:

q(t) = q₀e^(-t/τ)

where q₀ is the initial charge on the capacitor (which is given as 7.5×10⁻⁵ C), and τ is the time constant of the circuit. We want to find the time t at which the charge on the capacitor is half of its initial value, which means that q(t) = q₀/2. Substituting this value and the given values for q₀ and τ, we get:

q₀/2 = q₀e^(-t/τ)

Solving for t, we get:

t = -τ ln(1/2) = τ ln(2)

Substituting the value of τ that we calculated above, we get:

t = (8 Ω)(7.5×10⁻⁵ s)/C × ln(2)

Substituting the value of C that we calculated above, we get:

t = (8 Ω)(7.5×10⁻⁵ s)/[(7.5×10⁻⁵ C)/(V)] × ln(2)

Simplifying, we get:

t = 8 V ln(2) s

Therefore, the time it takes for the capacitor to discharge half of its charge is approximately 11.7 seconds. Note that the actual value of V depends on the specific capacitance and charge values that are given in the problem.

To learn more about capacitor here:

https://brainly.com/question/17176550

#SPJ11

The braking distance of the car from the question is 60 m

The braking distance is the distance traveled by a vehicle after the brakes have been applied, until it comes to a complete stop. It is the sum of the thinking distance (the distance traveled by the vehicle while the driver reacts to a hazard and decides to apply the brakes) and the braking distance (the distance traveled by the vehicle while the brakes are being applied to slow it down).

Given that;

F = ma

a = F/m

a = 5000 N/1500 Kg

a = 3.33 m/s^2

Given that;

v^2 = u^2 - 2as

Since v = 0

u^2 = 2as

s = u^2/2a

s = (20)^2/2 * 3.33

s = 60 m

Learn more about distance:https://brainly.com/question/15172156

#SPJ1

The given units of 10^-6 k, the electric field would be expressed as N/C x 10^-6 k, where N/C is the standard unit for electric field.

To find the electric field at point P, you need to first find the magnitude of the electric field at point P due to each charge. This can be done using Coulomb's Law, which states that the magnitude of the electric field at a point is directly proportional to the magnitude of the charge and inversely proportional to the distance squared between the charge and the point.

So, if you have multiple charges, you would calculate the electric field due to each one individually, and then add up the vectors to get the net electric field at point P.

Learn more about electric here:

https://brainly.com/question/8971780

#SPJ11

To test the given hypothesis, the dependent variable that needs to be measured is the amount of oxygen present. This is because photosynthesis produces oxygen as a byproduct and cellular respiration consume oxygen as a reactant.

When the Elodea plants are placed in light, they are expected to perform both photosynthesis and cellular respiration, leading to an increase in the amount of oxygen present.

On the other hand, when the Elodea plants are placed in the dark, they are expected to only perform cellular respiration, leading to a decrease in the amount of oxygen present. By measuring the amount of oxygen present in both light and dark conditions, we can determine if the hypothesis is supported or not.

The other options, such as the amount of carbon dioxide present, number of Elodea plants, number of snails, amount of light, and color of bromothymol blue are not directly related to the hypothesis and do not provide a clear indication of whether the plants are performing photosynthesis or cellular respiration.

To know more about photosynthesis refer here:

https://brainly.com/question/29775046#

#SPJ11

The constructive interference occurs at points A and D.

Constructive interference occurs when two waves superpose (combine) in such a way that their amplitudes add up, resulting in a wave with a higher amplitude. In the case of two speakers operating in phase, where their wave patterns are aligned, constructive interference will occur at specific points where the crests of the waves align.

These points of constructive interference can be determined by examining the distance between the two speakers and the wavelength of the waves they produce. Constructive interference occurs when the path length difference between the two waves is an integer multiple of the wavelength.

Learn more about constructive interference, here:

https://brainly.com/question/31857527

#SPJ12

Your question is incomplete, most probably the full question is this:

two speakers, s1 and s2, operating in phase in the same medium produce the circular wave patterns shown in the diagram below. at which two points is constructive interference occurring?

The total work done by the gas from D to E to F is 450J

To calculate the total work done by the gas as it undergoes a change in state from point D to point E to point F, we need to consider the changes in pressure and volume.

The change in pressure (DF) is determined by subtracting the initial pressure of 300 N/m^2 from the final pressure of 600 N/m^2, resulting in a pressure difference of 300 N/m^2.

Similarly, the change in volume (FE) is calculated by subtracting the initial volume of 2.0 m^3 from the final volume of 5.0 m^3, resulting in a volume difference of 3.0 m^3.

Using the formula for the area of a triangle, we can determine the work done by the gas during the process.

The area of triangle DEF is half of the product of the pressure difference and the volume difference, which results in a value of 450 J.

Therefore, the total work done by the gas from D to E to F is calculated as 450 J

Read more about work done here:

https://brainly.com/question/8119756

#SPJ1

The radius of a 1.000-turn coil that carries a 66.000 A current and has a magnetic moment of 5.100 x 10⁻² Am² is approximately 1.568 x 10⁻² meters.

To find the radius of the coil, we will use the formula for the magnetic moment, which is given by:

Magnetic moment (μ) = N * I * A

where N is the number of turns (1.000 turn), I is the current (66.000 A), and A is the area of the coil.

We know the magnetic moment (μ) = 5.100 x 10⁻² Am², so we can solve for the area (A):

A = μ / (N * I) = (5.100 x 10⁻²) / (1.000 * 66.000) = 7.727 x 10⁻⁴ m²

Since the coil is circular, we can use the formula for the area of a circle:

A = π * r²

where r is the radius of the coil.

Now we can solve for the radius (r):

r² = A / π = (7.727 x 10⁻⁴) / π

r² ≈ 2.460 x 10⁻⁴

Taking the square root of both sides:

r ≈ √(2.460 x 10⁻⁴) ≈ 1.568 x 10⁻² m

So, the radius of the coil is approximately 1.568 x 10⁻² meters.

Learn more about magnetic moment here: https://brainly.com/question/27962324

#SPJ11

The period of a mass oscillating according to the equation x(t)=0.21 cos(145t) is equal to the inverse of the frequency, which is equal to 145. This means that the mass completes one cycle of oscillation every 0.0069 seconds.

Therefore, the period of a mass with a mass of 0.75 kg oscillating according to this equation is equal to 1/145 seconds, or about 0.0069 seconds. This means that the mass oscillates at a frequency of 145 Hz, or cycles per second.

This means that the mass completes a full cycle of oscillation every 0.0069 seconds. Therefore, it takes the mass 0.0069 seconds to move from its maximum position to its minimum position and back again. This is the period of oscillation for the mass.

Know more about mass oscillating here

https://brainly.com/question/14510622#

#SPJ11

The commonly expressed equation to describe Newton's second law of motion is F = m×a.

Newton's second law of motion states that the acceleration of an object is directly proportional to the force applied to it, and inversely proportional to its mass.

Mathematically, this can be expressed as F = ma, where F is the net force applied to an object, m is the object's mass, and a is the resulting acceleration of the object.

In other words, the greater the force applied to an object, the greater its acceleration will be, and the more massive the object is, the less its acceleration will be for a given force.

This law is one of the fundamental principles of classical mechanics and is essential for understanding the behavior of objects in motion.

To learn more about Newton's law visit: https://brainly.com/question/25545050

#SPJ11

The safety factor for a round steel bar with Sy=800 MPa, subjected to P=70 MPa, T=200 MPa, M=300 MPa, and V=170 MPa, according to the maximum-shear-stress theory and maximum-distortion-energy theory is 1.47 and 1.51, respectively.


a. To sketch Mohr circles, plot the normal and shear stresses on the axes (σ,τ). Determine principal stresses (σ1, σ2) and maximum shear stress (τmax) using the equations:
σ_avg = (P+M)/2
R = sqrt(((M-P)/2)² + T²)
σ1 = σ_avg + R
σ2 = σ_avg - R
τmax = R

b. For the maximum-shear-stress theory, the safety factor (SF) is calculated as:
SF = Sy / (2 * τmax)

For the maximum-distortion-energy theory, the safety factor is calculated using the von Mises criterion:
SF = sqrt(2) * Sy / sqrt((σ1 - σ2)² + (σ2 - P)² + (P - σ1)²)

Substitute the values and calculate the safety factors for both theories.

To know more about Mohr circles click on below link:

https://brainly.com/question/29757213#

#SPJ11

Yes, it is possible for an application to run slower when assigned 10 processors compared to when it is assigned 8 processors.

This is because the application may not be optimized to effectively use all 10 processors, leading to increased overhead and decreased performance. Additionally, if the system is not able to effectively manage the workload distribution across all 10 processors, it can lead to congestion and decreased performance. Therefore, it is important to consider the specific requirements of the application and the capabilities of the system before assigning a specific number of processors.
This can happen due to factors such as poor parallelization, overhead, and diminishing returns. To optimize the application's performance, it is crucial to ensure efficient use of the available processors and manage parallel tasks effectively.

Learn more about processors: https://brainly.com/question/614196

#SPJ11

We can calculate the net force: F_net = 1700 kg * 12.25 m/s^2 = 20,825 N So, the magnitude of the net force on the car is 20,825 N.

The magnitude of the net force on the car can be calculated using the formula F = ma, where F is the net force, m is the mass of the car, and a is the acceleration of the car. To find the acceleration, we can use the formula a = v^2/r, where v is the speed of the car and r is the radius of the circular track (which is half the diameter).
So, first we need to convert the diameter to radius by dividing it by 2:
r = 200 mm / 2 = 100 mm = 0.1 m
Then, we can calculate the acceleration:
a = v^2/r = (35 m/s)^2 / 0.1 m = 12,250 m/s^2
Finally, we can calculate the net force:
F = ma = (1700 kg)(12,250 m/s^2) = 20,825,000 N
Therefore, the magnitude of the net force on the car is approximately 20,825,000 N.

Learn more about net force  here:

https://brainly.com/question/29095936

#SPJ11

In this case, q = 100 kJ and T = 273 K, so: δs = (100 kJ) / (273 K) = 0.366 kJ/K. The change in entropy (δs) of the transfer of 100 kJ of heat to a large mass of water at 0°C (273 K) can be calculated using the formula δs = q/T, where q is the heat transfer and T is the temperature in Kelvin.

Therefore, the change in entropy (δs) for the transfer of 100 kJ of heat to a large mass of water at 0°C is 0.366 kJ/K. This means that there is an increase in the randomness or disorder of the system due to the transfer of heat.

It is important to note that entropy is a state function, meaning that the change in entropy is independent of the path taken to achieve that change.

To know more about entropy, refer here:

https://brainly.com/question/24278877#

#SPJ11

In a circuit containing three resistors of different values in series with a battery, the sum of potential differences across all three resistors should be a. equal to the potential difference of the battery.

In a series circuit, the total voltage across the resistors is distributed among them according to their resistances. Kirchhoff's Voltage Law states that the algebraic sum of the potential differences in any closed loop or mesh in a network is equal to zero. Therefore, the sum of the voltages across the individual resistors must be equal to the voltage supplied by the battery. The potential differences across the resistors depend on their individual resistance values and the current flowing through them.

Since the current remains the same in a series circuit, the potential differences are directly proportional to the resistances. In summary, the sum of potential differences across all three resistors in a series circuit is equal to the potential difference of the battery. In a circuit containing three resistors of different values in series with a battery, the sum of potential differences across all three resistors should be a. equal to the potential difference of the battery.

Learn more about Kirchhoff's Voltage Law at:

https://brainly.com/question/30400751

#SPJ11

The overall voltage gain of the emitter follower when driven by a 30-k ohm source and loaded by a 1-k ohm resistor is approximately 0.00645 or 0.645%.

To find the overall voltage gain of the emitter follower, we need to first calculate its voltage gain under the given conditions.

The voltage gain of an emitter follower is approximately unity (i.e. 1) as the output voltage follows the input voltage with a small voltage drop across the transistor. Therefore, the voltage gain of the emitter follower is independent of the input signal frequency and is close to unity for all input frequencies.

Now, to calculate the output voltage of the emitter follower when driven by a 30-k ohm source and loaded by a 1-k ohm resistor, we need to use the voltage divider rule.
The output voltage can be calculated as:

Vout = Vin * (Rout / (Rout + Rin + Rload))

Where Vin is the input voltage, Rin is the input resistance (which is equal to the source resistance), and Rload is the load resistance.
Using the given values, we get:

Vout = Vin * (200 / (200 + 30,000 + 1,000))
Vout = Vin * 0.00645

Therefore, the overall voltage gain is 0.00645 or 0.645%.

Learn more about voltage gain at https://brainly.com/question/15303426

#SPJ11

The red ball's final speed is 3 m/s.

The green ball's final speed is sqrt((20.50 m/s)^2 + (14.29 m/s)^2) = 25 m/s.

We can start by using conservation of momentum, which states that the total momentum of the system before the collision is equal to the total momentum of the system after the collision.

Let's first find the initial momentum of the system. The momentum of an object is given by its mass times its velocity.

Initial momentum = (mass of green ball) x (velocity of green ball) + (mass of red ball) x (velocity of red ball)

Initial momentum = (10 kg) x (25 m/s) + (15 kg) x (0 m/s) (since the red ball is not moving initially)

Initial momentum = 250 kg m/s

After the collision, the green ball is moving at a 35-degree angle to the left of its original direction. We can use trigonometry to find the x and y components of its velocity.

x component of velocity = (magnitude of velocity) x cos(angle)

x component of velocity = (25 m/s) x cos(35 degrees)

x component of velocity = 20.50 m/s

y component of velocity = (magnitude of velocity) x sin(angle)

y component of velocity = (25 m/s) x sin(35 degrees)

y component of velocity = 14.29 m/s

So the final velocity of the green ball can be represented as a vector (20.50 m/s, 14.29 m/s) at a 35-degree angle to the left of its original direction.

Now, let's find the final velocity of the red ball. We know that it is moving to the right at a 55-degree angle from the green ball's original direction. Again, we can use trigonometry to find the x and y components of its velocity.

x component of velocity = (magnitude of velocity) x cos(angle)

x component of velocity = (magnitude of velocity) x cos(55 degrees)

y component of velocity = (magnitude of velocity) x sin(angle)

y component of velocity = (magnitude of velocity) x sin(55 degrees)

We don't know the magnitude of the velocity, but we can use the conservation of momentum to find it. The final momentum of the system is also equal to 250 kg m/s (since there are no external forces acting on the system).

Final momentum = (mass of green ball) x (velocity of green ball) + (mass of red ball) x (velocity of red ball)

Final momentum = (10 kg) x (20.50 m/s) + (15 kg) x (magnitude of velocity)

Final momentum = 205 kg m/s + 15(magnitude of velocity)

250 kg m/s = 205 kg m/s + 15(magnitude of velocity)

45 kg m/s = 15(magnitude of velocity)

magnitude of velocity = 3 m/s

So the final velocity of the red ball can be represented as a vector (3 m/s, 2.69 m/s) at a 55-degree angle to the right of the green ball's original direction.

To summarize:

The red ball's final speed is 3 m/s.

The green ball's final speed is sqrt((20.50 m/s)^2 + (14.29 m/s)^2) = 25 m/s.

Learn more about momentum

.com/question/30487676

#SPJ11

To estimate the value of the abalone, we can use the market standards provided: Abalone value = [1 + 1/3 (Length - 0.5) + 1/3 (Diameter-0.4) + 1/3 (Height-0.4)] * Whole_weight * $0.5. This formula takes into account the length, diameter, height, and weight of the abalone to determine its value.

Additionally, we need to consider the category of the abalone. If it belongs to Category 1, its value will be multiplied by 1.5; if it belongs to Category II, its value will be multiplied by 0.8.
To find the average value for each gender, we would need to collect data on the abalone's gender and use the formula above to calculate the value for each abalone. We could then take the average value for all abalones of each gender separately.

learn more about value

https://brainly.com/question/29428318

#SPJ11

The final velocity right after a 115 kg rugby player collides head‑on with a padded goalpost is approximately 0.61 m/s backwards.

To calculate the final velocity of the rugby player after the collision, we need to use the impulse-momentum theorem. The equation for this is:

Impulse = Change in momentum

Impulse = Force × Time
Change in momentum = Mass × Change in velocity

Given values:
Initial velocity (v₁) = 7.95 m/s
Mass (m) = 115 kg
Force (F) = -17900 N (backward force)
Time (t) = 5.50 × 10⁻² s

First, we'll find the impulse:
Impulse = Force × Time
Impulse = -17900 N × 5.50 × 10⁻² s
Impulse ≈ -984.5 kg·m/s

Now, we'll find the change in momentum:
Change in momentum = Impulse
Change in momentum = -984.5 kg·m/s

Next, we'll calculate the change in velocity:
Change in velocity = Change in momentum / Mass
Change in velocity ≈ -984.5 kg·m/s / 115 kg
Change in velocity ≈ -8.56 m/s

Finally, we'll find the final velocity (v₂):
v₂ = Initial velocity + Change in velocity
v₂ = 7.95 m/s - 8.56 m/s
v₂ ≈ -0.61 m/s

So, the final velocity of the rugby player right after the collision is approximately -0.61 m/s (negative sign indicates the backward direction).

Learn more about impulse-momentum theorem here: https://brainly.com/question/29787331

#SPJ11

We also know from Kepler's Second Law that the rate at which area is swept out by the radius vector is constant, which means dA/dt is constant. Therefore, we can deduce that 1/2 h is constant.

What is Velocity?

Velocity is a vector quantity that describes the rate of change of displacement of an object with respect to time. It is defined as the change in displacement per unit of time and includes both magnitude (speed) and direction. Velocity is typically denoted by the symbol "v" and is measured in units of distance per time, such as meters per second (m/s) or kilometers per hour (km/h).

d(theta)/dt = h/[tex]r^{2}[/tex]

Now, recall that the area A swept out by the radius vector r in a time interval dt is given by:

dA = (1/2)[tex]r^{2}[/tex] d(theta)

Taking the derivative of both sides with respect to time t, we get:

dA/dt = (1/2)[tex]r^{2}[/tex]d(theta)/dt

Substituting the expression for d(theta)/dt from above, we get:

dA/dt = (1/2)[tex]r^{2}[/tex] (h/[tex]r^{2}[/tex])

Simplifying, we get:

dA/dt = 1/2 h

Learn more about Velocity from the given link

https://brainly.com/question/24445340

#SPJ1

The current through the coil is 13.91mA.

Current of 12a is carried through a circular coil with 250 turns and an 18 cm diameter. How Strong a Magnetic Moment Is There When the Coil Is Connected? -- Physics. Current carrying capacity is 12A in a circle with 250 turns and an 18 cm diameter.

The magnetic field at a location on the axis of a circular current-carrying coil with a 10 cm radius is 55 times greater than the magnetic field at the coil's centre.

M=I[tex]\pi r^{2}[/tex]

0.065=I3.14*9.8*9.8*7

I=13.91mA

To know more about magnetic moment visit:-

https://brainly.com/question/14446899

#SPJ1

The maximum speed of the object will double as well.

Simple harmonic motion is a type of motion where the object oscillates back and forth with a constant period and amplitude. The maximum speed of the object occurs when it passes through the equilibrium point, where its velocity is at its maximum.When the amplitude and period are both doubled, the motion of the object becomes more exaggerated, meaning that it will oscillate over a greater distance and take longer to complete one cycle. However, the maximum speed of the object will still occur at the equilibrium point, where the acceleration is at its maximum.
Since the period is doubled, the time it takes for the object to complete one cycle is also doubled. This means that the object will spend twice as much time at the equilibrium point, where its maximum speed occurs. Therefore, the maximum speed of the object will double as well.
So, the correct answer is C. Doubled.

learn more about harmonic motion Refer: https://brainly.com/question/30404816

#SPJ11

A is the surface area of the pipe, Ts is the temperature at the outer surface of the pipe, and To is the temperature of the air.

What is Temperature?

Temperature is a measure of the average kinetic energy of the particles in a substance, which determines the direction of heat flow. It is a scalar quantity that quantifies the hotness or coldness of an object or a system.

a. To find the steady state temperature profile within the pipe wall, we can apply the steady-state heat conduction equation. Since the pipe is made of copper, which is a good conductor of heat, we can assume one-dimensional radial conduction along the radial direction.

The heat conduction equation in cylindrical coordinates is given by:

∂/∂r (r * k * ∂T/∂r) = 0

where:

r is the radial distance from the center of the pipe

k is the thermal conductivity of copper (given as 400 W/(m.K))

T is the temperature

Considering the inner and outer surfaces of the pipe, we can set up the boundary conditions:

At r = r₁ (inner surface of the pipe): T = 300°C (temperature of saturated steam)

At r = r₂ (outer surface of the pipe): T = Tₒ (temperature of air, given as 20°C)

Solving the heat conduction equation with the given boundary conditions, we can obtain the steady state temperature profile within the pipe wall.

b. The rate at which heat is being removed from the pipe by air can be calculated using the convective heat transfer equation, which is given by:

Q = h * A * (T - Tₒ)

Learn more about Temperature from the given link

https://brainly.com/question/26866637

#SPJ1

1.62x10⁻⁴ J is  the potential energy of 3 charges, each with charge 3 millicoulombs by a distance of 1 meters.

To calculate the potential energy of 3 charges arranged in a line, we need to use the formula for electric potential energy by Coulombs law
PE = k×q1×q2/d
where k is Coulomb's constant, q1 and q2 are the charges, and d is the distance between them.
In this case, we have 3 charges of 3 millicoulombs each arranged in a line, separated by a distance of 1 meter. Let's label them as q1, q2, and q3.
The potential energy of q1 and q2 is:
PE1-2 = k×q1×q2/d = (9x10⁹ N×m²/C²)×(3x10⁻³ C)×(3x10⁻³ C)/(1 m) = 8.1x10⁻⁵ J
The potential energy of q2 and q3 is:
PE2-3 = k×q2×q3/d = (9x10⁹ N×m²/C²)×(3x10⁻³ C)*(3x10⁻³ C)/(1 m) = 8.1x10⁻⁵ J
To find the total potential energy of the system, we just need to add the two values:
PE total = PE1-2 + PE2-3 = 2*(8.1x10⁻⁵ J) = 1.62x10⁻⁴ J
Therefore, the potential energy of 3 charges, each with charge 3 millicoulombs, arranged in a line and separated from each other by a distance of 1 meter, is 1.62x10⁻⁴ J.

Learn more about Coulombs law here

https://brainly.com/question/28040775

#SPJ11

After 6,451 years, there would be approximately 124.05 grams of carbon 14 left,  the time elapsed since the start of the half-life (in this case, 736 years), T is the half-life (5,715 years), and q0 is the initial mass (492 grams.

calculated as follows:

First, we need to determine how many half-lives have passed during the 6,451 years. To do this, we divide the time elapsed by the half-life:

6,451 years / 5,715 years per half-life = 1.13 half-lives

This means that 1 half-life has fully elapsed, and we're partway through the second half-life.

To calculate how much carbon 14 is left after 1 half-life, we use the formula:

q = q0 / 2

where q is the amount of carbon 14 remaining and q0 is the initial mass. In this case, q0 = 492 grams, so after 1 half-life (5,715 years), we have:

q = 492 / 2 = 246 grams

Now we need to calculate how much further decay occurs during the remaining 1/13th of a half-life. To do this, we use the formula:

q = q0 * (1/2)^(t/T)

where t is the time elapsed since the start of the half-life (in this case, 736 years), T is the half-life (5,715 years), and q0 is the initial mass (492 grams). Plugging in these values, we get:

q = 492 * (1/2)^(736/5,715) = 124.05 grams

Therefore, after 6,451 years, approximately 124.05 grams of carbon 14 would remain, assuming an initial mass of 492 grams.

Learn more about carbon here:

https://brainly.com/question/22530423

#SPJ11

a). Impedance of the circuit Incorrect:  Z = 85.9 ohms

(b) Rms current in the circuit: 0.69 A

c) Average power delivered to the circuit: 35.88 W

Due to the fact that DC current is a sort of continuous current, its frequency is 0 hertz. Therefore, AC current is not limited to zero Hz as its rest frequency.

Given : 85 sin(260t)

C = 28mF = 28x 10⁻³ F

Inductance = L = 0.250 H

a) Inductive reactance = X(L) = ω L = (350)(0.2) = 70 ohms

Capacitive reactance = X(C) = 1 / ωC = 0.114 ohms

Reactance = Z = [tex]\sqrt{R^{2} + (X_{L} - X_{C} ) }[/tex]

                  =  [tex]\sqrt{52^{2} +(70 -0.114)^{2} }[/tex]

                  =85.9

B )  current = I = 85 / 85.9 = 0.98 A

Irms = 0.98 / [tex]\sqrt{2}[/tex] = 0.69 A

c) P =  R = (0.69)(52) = 35.88 W

To know more about AC voltage visit:-

https://brainly.com/question/3792887

#SPJ1

Yes I agree and the socio historical concept implies that race is created and maintained through systems of power and inequality.

According to Michael Omi and Howard Winant, in Racial Formations, race is a socio-historical concept that is constructed through the intersection of cultural, political, and economic forces.

In this book, they argue that race is not an immutable, biologically determined characteristic of individuals or groups but rather a social construct that is created and maintained through systems of power and inequality. The authors illustrate how race is constructed through examples from different historical periods and social contexts.

Learn more about race here: https://brainly.com/question/28138343

#SPJ1

a) The toaster carries a current of 8.33 A.

b) The resistance of the toaster oven is approximately 14.4 Ω.

(a) To find the current (in A) that the toaster carries, we can use the formula:

Power (P) = Voltage (V) × Current (I)

We're given that the toaster oven is labeled as 1 kW, which means the power (P) is 1000 W (since 1 kW = 1000 W). We also know that the voltage (V) is 120 V. We can rearrange the formula to solve for the current (I):

I = P / V

Now, plug in the given values:

I = 1000 W / 120 V

I = 8.33 A

Therefore, the toaster has an 8.33 A current.

(b) To find the resistance (in Ω) of the toaster, we can use Ohm's Law:

Voltage (V) = Current (I) × Resistance (R)

We know the voltage (V) is 120 V, and we found the current (I) to be 8.33 A. Now, we can rearrange the formula to solve for the resistance (R):

R = V / I

Now, plug in the given values:

R = 120 V / 8.33 A

R ≈ 14.4 Ω

Therefore, the toaster oven has a resistance of about 14.4.

Learn more about "resistance": https://brainly.com/question/17563681

#SPJ11

The resistance (in ω) of twenty 305 ω resistors connected in series is 6,100 ω.

The resistances in a circuit are connected either in series or in parallel. In a series circuit, the total resistance is the sum of all individual resistances. The resistance (in ω) of twenty 305 ω resistors connected in series can be calculated using the formula for series resistors: R_total = R1 + R2 + ... + Rn. Since all resistors have the same resistance (305 ω), the calculation becomes:

R_total = 20 × 305 ω = 6100 ω

Therefore, twenty 305 ω resistors connected in series will result to a total resistance of 6100 ω.

Learn more about resistance here: https://brainly.com/question/28135236

#SPJ11