In travelling the 70cm along a rifle barrel, a bullet uniformly accelerates from rest to a velocity of 210m/s .Find the acceleration involved and the time taken for which the bullet is in the barrel.​

The speed of the rock as it hits the ground, neglecting air resistance, is 30.87 m/s.

The speed of the rock as it hits the ground can be found using the equation:-
v = g * t
where v is the speed of the rock, g is the acceleration due to gravity (9.8 m/s^2), and t is the time taken for the rock to hit the ground (3.15 seconds).
Substituting the given values, we get:-
v = 9.8 m/s^2 * 3.15 s
v = 30.87 m/s
Therefore, neglecting air resistance, the speed of the rock as it hits the ground is 30.87 m/s. It is important to note that air resistance would affect the speed of the rock and cause it to hit the ground at a slower speed.

Learn more about speed: https://brainly.com/question/4931057

#SPJ11

When a magnet is plunged into a coil at speed v, a voltage is induced in the coil and a current flows in the circuit. If the speed of the magnet is doubled, the induced voltage is:

According to Faraday's law of electromagnetic induction, the magnitude of the induced voltage is directly proportional to the rate of change of magnetic flux through the coil. When the speed of the magnet is doubled, the rate of change of magnetic flux also doubles, resulting in the induced voltage being twice as great.

Correct answer is a.) twice as great
This is because the induced voltage is directly proportional to the rate of change of the magnetic field, which in turn is directly proportional to the speed of the magnet. When the speed doubles, the rate of change of the magnetic field also doubles, resulting in the induced voltage being twice as great.

To know more about Faraday's law of electromagnetic induction:

https://brainly.com/question/13369951

#SPJ11

Answer:

The best way for Eli to check his results would be to compare his results with others doing the same investigation.

Explanation:

Comparing results with others doing the same investigation is a good way to verify scientific findings and confirm that the experiment was conducted correctly. This process is known as peer review and helps to ensure that the data collected is accurate and reliable. By comparing his results with others, Eli can check if there are any significant differences or inconsistencies that need to be addressed. This is an important step in the scientific process, and it helps to improve the overall quality of the research.

The maximum bending stress occurs at the bottom of the beam where the beam is experiencing maximum compression due to the bending moment. The bending moment is given by [tex]M = wl^2/8,[/tex] where w is the load per unit length and l is the length of the beam.

The bending stress is given by [tex]σ = My/I[/tex], where M is the bending moment, y is the distance from the neutral axis to the bottom of the beam, and I is the moment of inertia of the cross-sectional area of the beam.

For a rectangular beam of width b and height h, the moment of inertia is I =[tex]bh^3/12.[/tex] For a circular beam of diameter d, the moment of inertia is I = πd^4/64. For a trapezoidal beam with height h, small base b1, and large base b2, the moment of inertia is [tex]I = h(b1^2+b2^2+b1b2)/12.[/tex] For a triangular beam with height h and base b, the moment of inertia is I = [tex]bh^3/36.[/tex]

Substituting the values of w and l, we get M = 56250 lb-ft.

For the rectangular beam, the moment of inertia is[tex]I = bh^3/12 = b(30/2)^3/12 = 5625b[/tex]. Therefore, the maximum bending stress is [tex]σ = My/I = (56250)(15)/5625b = 150/b.[/tex]

Comparing the expressions for maximum bending stress in each beam, we see that the trapezoidal beam has the lowest maximum bending stress for any given set of dimensions. However, it should be noted that the shape of the beam is not the only factor to consider when selecting a beam for a specific application

To learn more about  gravitational potential here

https://brainly.com/question/15896499

#SPJ4

Therefore, interest rates and the discount factors are 0.9751, 0.9348, 0.8964, 0.8579, and 0.8197; the forward discount factors are 0.9557, 0.9605, 0.9543, and 0.9537; and the forward rates are -0.0456, 0.0246, -0.0556, and -0.0135.

The discount factors, we use the formula:

Z(0,T) = [tex]e^{(-r(0,T)*T)}[/tex]

where r(0,T) is the interest rate at time 0 for maturity T.

Using the given values, we get:

Z(0,0.5) = [tex]e^{(-0.06520.5)}[/tex] = 0.9751

Z(0,1) = [tex]e^{(-0.06711)[/tex]= 0.9348

Z(0,1.5) = [tex]e^{(-0.06791.5)[/tex]= 0.8964

Z(0,2) = [tex]e^{(-0.06722)[/tex] = 0.8579

Z(0,2.5) = [tex]e^{(-0.0679*2.5)[/tex] = 0.8197

To calculate the forward discount factors, we use the formula:

F(0,T-A,T) = Z(0,T)/(Z(0,T-A))

Using the calculated discount factors, we get:

F(0,0.5,1) = Z(0,1)/(Z(0,0.5)) = 0.9557

F(0,1,1.5) = Z(0,1.5)/(Z(0,1)) = 0.9605

F(0,1.5,2) = Z(0,2)/(Z(0,1.5)) = 0.9543

F(0,2,2.5) = Z(0,2.5)/(Z(0,2)) = 0.9537

To calculate the forward rates, we use the formula:

f(0,T-A,T) = ln(F(0,T-A,T))/A

Using the calculated forward discount factors, we get:

f(0,0.5,1) = ln(F(0,0.5,1))/0.5 = -0.0456

f(0,1,1.5) = ln(F(0,1,1.5))/0.5 = 0.0246

f(0,1.5,2) = ln(F(0,1.5,2))/0.5 = -0.0556

f(0,2,2.5) = ln(F(0,2,2.5))/0.5 = -0.0135

Learn more about interest rates visit: brainly.com/question/25720319

#SPJ4

The sphere that will have the largest moment of inertia is (b) a sphere with all mass distributed evenly over a thin shell at r = R.

The moment of inertia depends on the distribution of mass in an object. In the case of the four spheres you described, the sphere with the largest moment of inertia will be the one with the mass concentrated farthest from the center.

The moment of inertia of a solid sphere with uniform mass distribution (option a) is given by:

I = (2/5)mr²

where m is the total mass of the sphere and r is its radius.

For option b, since all the mass is distributed evenly over a thin shell at r = R, the moment of inertia is given by:

I = 2mr^(2/3)

For option c, the moment of inertia is given by:

I = (3/10)mr²

For option d, the moment of inertia is given by:

I = (2/3)mr²

Comparing these options, the sphere with the largest moment of inertia is option (b), where the mass is distributed evenly over a thin shell at r = R.

Learn more about moment of inertia here: https://brainly.com/question/29652198

#SPJ11

The unit of Specific Gravity is dimensionless.

The statement explains that specific gravity is a dimensionless unit, which means that it has no unit associated with it. Specific gravity is used to compare the density of a substance to the density of a reference substance, usually water. It is a ratio of the two densities and is expressed as a number without any unit. Although density and specific gravity are related, they are not the same thing. Density is typically measured in units such as kg/m³ or g/cm³, while specific gravity is a unitless number that compares the densities of two substances.

Know more about Specific Gravity here:

https://brainly.com/question/29816873

#SPJ11

The Aharonov-Bohm effect is a fascinating manifestation of the strange and counterintuitive behavior of quantum particles, and has provided important insights into the nature of the universe at the subatomic level.

The Aharonov-Bohm effect is a quantum mechanical phenomenon that describes the behavior of charged particles in the presence of a magnetic field, even when they are not directly interacting with the field itself. This effect arises due to the influence of the vector potential, which is a mathematical quantity that describes the magnetic field.

The effect was first predicted by Yakir Aharonov and David Bohm in 1959, who proposed that the vector potential could affect the phase of the wavefunction of a charged particle, leading to observable interference effects. In other words, even when a particle is shielded from a magnetic field, it can still be influenced by the field through the vector potential, which alters the phase of the particle's wavefunction.

This effect has been demonstrated experimentally using electron interferometry, where electrons are split into two paths and then recombined, producing interference patterns that depend on the strength and geometry of the magnetic field. The Aharonov-Bohm effect has important implications for our understanding of the fundamental principles of quantum mechanics, including the role of gauge symmetry and the relationship between electric and magnetic fields.
Here you can learn more about Aharonov-Bohm effect

https://brainly.com/question/30067997#

#SPJ11  

(a) The current in the 10-Ohm resistor is 1.6 A.

(b) The voltage on the 2-Ohm resistor is 19.2 V.

To solve this question, the total resistance of the circuit must be calculated first. Using the formula for resistors in parallel, the total resistance of the circuit is 1.6 Ohms.

Therefore, the current in the 10-Ohm resistor is the total current minus the current in the other two resistors;

7.5 - 4.0 - 6.0 = 1.6 A.

To calculate the voltage on the 2-Ohm resistor, the voltage drop across each resistor in the circuit must be calculated first.

12.0 - 16.0 - 36.0 = 19.2 V.

Learn more about formula for resistors at: https://brainly.com/question/16682686

#SPJ11

The value of Ios at which the current turns on depends on the specific transistor's characteristics and its threshold voltage. Once you have your plot, you can identify the Ios value where the current starts to flow by looking for the point at which the curve starts to rise significantly.

When setting Vps to a constant value of 5 V and sweeping the gate voltage from 0 V to 5 V in increments of 0.1 V, the curve of I vs. los can be plotted.

he value of los at which the current turns on can be determined from this curve. It is important to note that when Vps is held constant, the voltage across the transistor remains constant as well, which ensures that the transistor is operating in the saturation region.

As the gate voltage is increased, the electric field at the gate oxide interface increases, resulting in a higher channel potential and a larger drain current. At some point, the threshold voltage is reached, and the current starts to turn on. The exact value of los at which this occurs can be determined by analyzing the I vs. los curve.

Learn more about value here:

https://brainly.com/question/30781415

#SPJ11

Newton's third law states equal magnitudes of forces between truck and car but the direction varies. Zero when coasting, the same as a truck when accelerating, and the opposite when a car has resistance.

In all three scenarios, the magnitude of the force that the truck exerts on the car (FTC) is equal to the magnitude of the force that the car exerts on the truck (FC) according to Newton's third law of motion. However, the direction of the force may vary depending on the situation.
In the first scenario, where the truck is coasting along with a constant velocity on a horizontal surface neglecting friction, the force of the truck pulling the car is equal to the force of the car pulling back on the truck, which is equal to zero since there is no acceleration or resistance.
In the second scenario, where the truck is speeding up while driving up a mountain neglecting friction, the force of the truck pulling the car is greater than the force of the car pulling back on the truck since the truck is accelerating. Therefore, the direction of the force is in the same direction as the truck's motion up the mountain.
In the third scenario, where the truck is driving with a constant velocity, but the driver of the car left the emergency brake on, the force of the truck pulling the car is equal to the force of the car pulling back on the truck, which is greater than zero due to the resistance caused by the emergency brake. Therefore, the direction of the force is opposite to the direction of the truck's motion.

learn more about Newton's third law here:

https://brainly.com/question/29768600

#SPJ11

The ratio of initial speed of pendulum [tex]\frac{v_{1} }{v_{2} }[/tex] is [tex]\frac{M+m}{m} \sqrt{2gL(1-cos}[/tex] with mass m is fired with an initial speed v0 at a pendulum bob.

Conservation of Momentum can be used to determine the first half:

[tex]mv_{o} =(M+m)v[/tex]

Calculate the initial speed first, then apply the principle of conservation of energy to determine the height the pendulum will reach.  The final speed of the two objects after they come together is related to the kinetic energy for the "initial" in the Conservation of Energy equation by the relationship that we just established:

[tex]\frac{1}{2}(M+m)v=(M+m)gh[/tex]

The height of the pendulum in terms of L and Фmust be calculated because the mass cancels on both sides, which may be done using trig:

Think of the pendulum's starting point and ending point as the two sides of a right triangle, with an angle in between.  The triangle is rotatable By tracing the pendulum's final movement back to where the string was initially placed, a right triangle is formed.  As a result, we are able to determine that the pendulum's vertical displacement is equal to h and that the vertical leg's length is L-h(cos Ф).  Therefore:

since[tex]cosФ=\frac{L-h}{L}[/tex]

In order to understand that, we may change this to [tex]\frac{1}{2}(M+m)v=(M+m)gh[/tex]  to see that [tex]\frac{1}{2}v_{0} =gL(1-cos Ф)[/tex]

Once the velocity has been determined, simply substitute it into the Conservation of Momentum formula:

[tex]\frac{M+m}{m} \sqrt{2gL(1-cos}[/tex]

Put the values into the equation above in SI units to solve the second portion.

For more information on speed of pendulum kindly visit to

https://brainly.com/question/29266111

#SPJ1

The lens should have a f = 0.520 m focal length, and the picture distance should be s' = 2s = 1.734 m.

Analyze the focal length to see whether it is positive or negative. Decide whether the object distance is positive or negative in step two. Step 3: Determine how far the image is from the lens using the equation di=11f1do d I = 1 1 f 1 d o.

Assuming that the lens is thin, we can use the thin lens equation to relate the object distance (s) and image distance (s') to the focal length (f):

1/f = 1/s + 1/s'

We can use similar triangles to relate the object distance s and image distance s' to the heights h and h':

h / s = h' / s'

Substituting h = 2 cm and h' = 4 cm, we have:

[tex]2 cm / s = 4 cm / s'[/tex]

s' = 2 s

Substituting this expression for s' into the thin lens equation, we have:

1/f = 1/s + 1/2s

3/2s = 1/f

s = 2f/3

Now, we can use the given distance from the spider to the wall to set up another equation:

s + s' = 2.6 m

Substituting s' = 2s, we have:

s + 2s = 2.6 m

s = 0.867 m

Substituting this value of s into the expression for s in terms of f, we have:

0.867 m = 2f/3

f = 0.520 m

To know more about focal length visit:-

https://brainly.com/question/29870264

#SPJ1

The terminal voltage of the large 1.05 V carbon-zinc dry cell is 0.825 V when supplying 1.50 A to a circuit with an internal resistance of 0.150 Ω.

To calculate the terminal voltage of the carbon-zinc dry cell, we can use Ohm's Law which states that V = I*R, where V is the voltage, I is the current, and R is the resistance.

In this case, the current is given as 1.50 A and the internal resistance is 0.150 Ω. So,

V = I*R
V = 1.50 A * 0.150 Ω
V = 0.225 V

However, this is the voltage drop across the internal resistance of the cell. To find the terminal voltage, we need to subtract this voltage drop from the initial voltage of the cell, which is 1.05 V.

Terminal voltage = Initial voltage - Voltage drop
Terminal voltage = 1.05 V - 0.225 V
Terminal voltage = 0.825 V

To learn more about Ohm's Law click here

brainly.com/question/1247379

#SPJ11

The impulse experienced by the Juggernaut and Colossus are related to the average force each superhero experiences during the collision. The impulses are equal in magnitude but opposite in direction.

The impulse experienced by Juggernaut is equal to the product of its mass and the change in velocity from before and after the collision. Similarly, the impulse experienced by Colossus is equal to the product of its mass and the change in velocity from before and after the collision.

The total impulse of the collision is zero, so the impulses experienced by the two characters must be equal and opposite. This means that the average force experienced by each character must be equal in magnitude and opposite in direction. This is because the impulse experienced by each character is equal to the average force multiplied by the time that force acts on the character.

Know more about impulse here

https://brainly.com/question/30466819#

#SPJ11

Therefore, the tension in the rope is -720 N. Note that the negative sign indicates that the tension is in the opposite direction to the force applied.

(a)  The pole and cable are massless.

The pin at point C provides a vertical reaction force and a horizontal reaction force.

The cable and pole are inextensible, meaning that their lengths do not change under load.

Free body diagram:

Let T be the tension in the cable AD, and let R_Cx and R_Cy be the horizontal and vertical components of the reaction force at point C, respectively.

(b) Complete set of equilibrium equations:

The system is in static equilibrium, which means that the net force and the net torque acting on the pole must both be zero. We can write the following equations:

∑F_x = 0: R_Cx - T cos(a) = 0 (horizontal equilibrium)

∑F_y = 0: F1 + R_Cy - T sin(a) - F2 = 0 (vertical equilibrium)

∑τ_C = 0: - T sin(a) * AD + F2 * AC = 0 (torque equilibrium about point C)

(c)  We can solve the equilibrium equations to find the unknowns:

From ∑F_x = 0, we have R_Cx = T cos(a).

From ∑F_y = 0, we have R_Cy = F2 - F1 - T sin(a).

Substituting these values into ∑τ_C = 0, we get:

T sin(a) * AD + F2 * AC = 0

T sin(a) * 0.8 m + 120 N * 1.2 m = 0

T sin(a) = - 120 N * 1.2 m / 0.8 m

T sin(a) = - 180 N

Substituting this value of T sin(a) into ∑F_y = 0, we get:

F1 + R_Cy - T sin(a) - F2 = 0

40 N + R_Cy + 180 N - 120 N = 0

R_Cy = - 100 N

Since the vertical reaction force at point C is negative, it means that the pin is exerting an upward force on the pole to balance the downward forces from F1, F2, and T.

Finally, substituting the values of R_Cx and R_Cy into ∑F_x = 0, we get:

R_Cx - T cos(a) = 0

T cos(a) = R_Cx

T cos(30°) = R_Cx

T = R_Cx / cos(30°)

T = (T sin(a) / sin(a)) / cos(30°)

T = - 180 N / sin(30°) / cos(30°)

sin 30° = 1/2

cos 60° = 1/2

T = -180 N / (1/2 × 1/2) = -180 N / 1/4 = -180 N × 4

So:

T = -720 N

Learn more about tension visit: brainly.com/question/24994188

#SPJ4

She have to perform 27 reps of this lift to burn off approximately 350 calories.

To determine how many reps are required for her to burn off 350 calories while lifting a 7.8 kg barbell through a distance of 0.72 m, we need to follow these steps:
1. Calculate the work done per rep: Work = force x distance
2. Convert work done to calories
3. Calculate the number of reps required to burn 350 calories

Step 1: Calculate the work done per rep
Force = mass x acceleration due to gravity (g = 9.81 m/s^2)
Force = 7.8 kg x 9.81 m/s^2 = 76.518 N (Newtons)
Work = force x distance = 76.518 N x 0.72 m = 55.093 J (Joules)

Step 2: Convert work done to calories
1 calorie = 4.184 Joules
Work done in calories = 55.093 J / 4.184 J/cal = 13.17 cal

Step 3: Calculate the number of reps required to burn 350 calories
Number of reps = 350 cal / 13.17 cal/rep = 26.56 reps

To know more about "Calories" refer here:

https://brainly.com/question/7149361#

#SPJ11

Your answer: (c) toward the blue end of the spectrum.

Explanation: When you are in a spaceship moving very quickly toward Earth, the light emitted from the headlights will experience a phenomenon called the Doppler effect. The Doppler effect causes the wavelength of the light to change due to the relative motion between the light source (spaceship) and the observer (people on Earth).
Since you observe the headlights to emit red light, and you are moving towards Earth, the wavelengths of the light will be compressed, causing the light to shift towards the blue end of the spectrum. So, people on Earth will observe your headlights to be a color towards the blue end of the spectrum.

To know more about the Doppler effect:

https://brainly.com/question/15318474

#SPJ11

The pivot should be placed 1.31 m from the left end of the board to balance the seesaw when you sit on the left end and your friend sits on the right end, taking into account the mass of the board.

T1 = 90 kg * g * (x - 1.5 m)

T2 = 60 kg * g * (1.5 m - x).

T3 = Mg * (L/2 - x)

In the equilibrium position, we set the sum of the torques equal to zero:

T1 + T2 + T3 = 0

90 kg * g * (x - 1.5 m) + 60 kg * g * (1.5 m - x) + Mg * (L/2 - x) = 0

Simplifying and solving for x, we get:

x = (45 kg * L + 1.5 m * (90 kg - 60 kg)) / (M + 150 kg)

Substituting the values given in the problem, with M = 29 kg, we get:

x = (45 kg * 3.0 m + 1.5 m * 30 kg) / (29 kg + 150 kg)

x = 1.31 m

Torque is a measure of the force that causes an object to rotate around an axis or pivot point. It is often described as the rotational equivalent of force. The amount of torque an object experiences is dependent on both the magnitude and direction of the applied force, as well as the distance between the axis of rotation and the point where the force is applied.

The formula for torque is τ = r × F, where τ is the torque, r is the distance between the axis of rotation and the point of force application, and F is the magnitude of the applied force. Torque is typically measured in units of Newton meters (Nm) or pound-feet (lb-ft). Torque is an important concept in many areas of physics, including mechanics, engineering, and robotics. It plays a critical role in the operation of machines and engines, as well as in the movement and control of vehicles and aircraft.

To learn more about Torques visit here:

brainly.com/question/6855614

#SPJ4

The speed of the clay just before it hits the pan can be calculated using the conservation of energy principle.

According to the conservation of energy principle, the total energy of the system remains constant. Initially, the clay has only potential energy due to its height, which is given by mgh, where m is the mass of the clay, g is the acceleration due to gravity, and h is the height from which the clay is dropped.

When the clay hits the pan, it comes to rest, and its potential energy is converted into the potential energy of the spring. If the spring has a spring constant k, then the potential energy stored in the spring is given by (1/2)kx^2, where x is the displacement of the spring from its equilibrium position.

Since the pan and spring are massless, the total energy of the system before and after the collision is the same. Therefore, we can equate the potential energy of the clay to the potential energy of the spring, and solve for the speed of the clay just before it hits the pan:

mgh = (1/2)kx^2

x = (mgh/k)^0.5

The displacement of the spring is equal to the distance that the clay compresses the spring. This distance is also equal to the maximum height that the clay rises after the collision, which is given by h' = x + (m/k)g.

Therefore, the total distance traveled by the clay after the collision is h + h', and the time taken to travel this distance is given by t = (2(h+h')/g)^0.5.

Finally, the speed of the clay just before it hits the pan can be calculated using the formula v = gt:

v = g(2(h + x + (m/k)g))^0.5

For more questions like Energy click the link below:

https://brainly.com/question/12807194

#SPJ11

50 filter boxes would be required for the dual-media filter with a hydraulic loading rate of 300 m3/d.m2.

To answer this question, we need to use the same approach as in problem 11-1 but with the given hydraulic loading rate of 300 m3/d.m2 for the dual-media filter.

The filtration rate for a dual-media filter is typically higher than for a standard filter.

Let's assume a filtration rate of 10 m/d for the dual-media filter, which is a typical range for this type of filter.The total filtration area required can be calculated as:

A = Q/Rwhere Q is the flow rate and R is the filtration rate.

For the dual-media filter, Q = 10,000 m3/d (given in problem 11-1) and R = 10 m/d.

Therefore, A = 10,000 m3/d / 10 m/d = 1,000 m2

To calculate the number of filter boxes required, we need to divide the total filtration area by the area of one filter box

Let's assume a filter box area of 20 m2, which is typical for a dual-media filter.

Number of filter boxes = A / Area per filter box

Number of filter boxes = 1,000 m2 / 20 m2 = 50

To know more about dual-media, click here.

https://brainly.com/question/29583346

#SPJ4

50 filter boxes would be required for the dual-media filter with a hydraulic loading rate of 300 m3/d.m2.

To answer this question, we need to use the same approach as in problem 11-1 but with the given hydraulic loading rate of 300 m3/d.m2 for the dual-media filter.

The filtration rate for a dual-media filter is typically higher than for a standard filter.

Let's assume a filtration rate of 10 m/d for the dual-media filter, which is a typical range for this type of filter.The total filtration area required can be calculated as:

A = Q/Rwhere Q is the flow rate and R is the filtration rate.

For the dual-media filter, Q = 10,000 m3/d (given in problem 11-1) and R = 10 m/d.

Therefore, A = 10,000 m3/d / 10 m/d = 1,000 m2

To calculate the number of filter boxes required, we need to divide the total filtration area by the area of one filter box

Let's assume a filter box area of 20 m2, which is typical for a dual-media filter.

Number of filter boxes = A / Area per filter box

Number of filter boxes = 1,000 m2 / 20 m2 = 50

To know more about dual-media, click here.

https://brainly.com/question/29583346

#SPJ4

Approximately it will take the particle 20.567 seconds to complete one orbit.

A particle moving in a circular orbit in a magnetic field.

To determine the speed of the 10.8 μC particle with a mass of 2.90×10⁻⁵kg moving in a circular orbit with a radius of 28.2 m in a 0.810 T magnetic field, we'll use the following equation:

v = (q×B×r) / m

where v is the speed of the particle, q is the charge (10.8 μC), B is the magnetic field strength (0.810 T), r is the radius of the orbit (28.2 m), and m is the mass of the particle (2.90×10⁻⁵ kg).

First, convert the charge from microcoulombs to coulombs: 10.8 μC = 10.8 × 10⁻⁶C

Now, plug in the values:

v = (10.8 × 10⁻⁶ C×0.810 T×28.2 m) / 2.90×10⁻⁵ kg

v ≈ 8.582 m/s

The particle is moving at approximately 8.582 m/s.

Next, we'll determine the time it takes for the particle to complete one orbit. Since the particle is moving in a circular path, we'll use the following equation:

T = 2×π×r / v

where T is the time it takes to complete one orbit, r is the radius (28.2 m), and v is the speed (8.582 m/s).

Plug in the values:

T = 2×π×28.2 m / 8.582 m/s

T ≈ 20.567 s

It will take the particle approximately 20.567 seconds to complete one orbit.

Learn more about magnetic field.

brainly.com/question/14848188

#SPJ11

The magnetic field at a distance of 5 cm from the wire is 2.00 mT.

To find the current in the loop, we can use Ampere's Law, which relates the magnetic field around a current-carrying loop to the current in the loop. For a single loop, the formula is:
B = (μ₀ * I) / (2 * R),
where B is the magnetic field, μ₀ is the permeability of free space (4π × 10^(-7) T·m/A), I is current, and R is the radius of the loop.
Given the magnetic field B = 2.00 mT = 2.00 × 10^(-3) T and the diameter of the loop as 1.00 cm = 0.01 m, we can calculate the current:
1. The radius R = diameter / 2 = 0.01 m / 2 = 0.005 m
2. Rearranging the formula for I: I = (2 * R * B) / μ₀
3. Substituting the values: I = (2 * 0.005 m * 2.00 × 10^(-3) T) / (4π × 10^(-7) T·m/A)
4. Calculating the current: I ≈ 1.59 A
So, the current in the loop is approximately 1.59 A.
Now, to find the distance (r) from the long straight wire carrying the same current (1.59 A) where the magnetic field is 2.00 mT, we use the formula for the magnetic field around a straight wire:
B = (μ₀ * I) / (2 * π * r)
Rearranging the formula for r and substituting the values:
1. r = (μ₀ * I) / (2 * π * B)
2. r = (4π × 10^(-7) T·m/A * 1.59 A) / (2 * π * 2.00 × 10^(-3) T)
3. Calculating the distance: r ≈ 0.100 m
At a distance of approximately 0.100 m (10 cm) from the wire, the magnetic field is 2.00 mT.

Learn more about  permeability here: https://brainly.com/question/31565966

#SPJ11

The beat frequency produced when the two organ pipes play together in their fundamental is 1.676 Hz.

When one of the organ pipes is lengthened by 2.60cm, its new length becomes 1.024m (1.02m + 0.026m). The fundamental frequency of an organ pipe that is open at one end and closed at the other is given by the formula:
f = (n/2L) * v
where f is the frequency, n is the harmonic number (1 for the fundamental), L is the length of the pipe, and v is the speed of sound.
For both pipes, the length L is 1.02m. Therefore, the fundamental frequency of each pipe is:
f1 = (1/2*1.02) * v
f2 = (1/2*1.024) * v
When the two pipes play together, they produce a beat frequency equal to the difference between their frequencies. Therefore, the beat frequency is:
fbeat = |f1 - f2| = |(1/2*1.02) - (1/2*1.024)| * v
Simplifying the expression, we get:
fbeat = (0.002/2.04) * v
Substituting the value of the speed of sound (343 m/s), we get:
fbeat = 1.676 Hz

learn more about frequency Refer: https://brainly.com/question/30783512

#SPJ11

The beat frequency produced when the two organ pipes play together in their fundamental is 1.676 Hz.

When one of the organ pipes is lengthened by 2.60cm, its new length becomes 1.024m (1.02m + 0.026m). The fundamental frequency of an organ pipe that is open at one end and closed at the other is given by the formula:
f = (n/2L) * v
where f is the frequency, n is the harmonic number (1 for the fundamental), L is the length of the pipe, and v is the speed of sound.
For both pipes, the length L is 1.02m. Therefore, the fundamental frequency of each pipe is:
f1 = (1/2*1.02) * v
f2 = (1/2*1.024) * v
When the two pipes play together, they produce a beat frequency equal to the difference between their frequencies. Therefore, the beat frequency is:
fbeat = |f1 - f2| = |(1/2*1.02) - (1/2*1.024)| * v
Simplifying the expression, we get:
fbeat = (0.002/2.04) * v
Substituting the value of the speed of sound (343 m/s), we get:
fbeat = 1.676 Hz

learn more about frequency Refer: https://brainly.com/question/30783512

#SPJ11

The gauge that reads absolute pressure in the tank will show a constant pressure reading, as it measures the pressure relative to a complete vacuum (i.e. absolute zero pressure).

A gauge is a device used for measuring or displaying various physical quantities, such as pressure, temperature, or fluid flow rate. Gauges can be analog or digital and come in a variety of forms, depending on the specific application and measurement being made.

One common type of gauge is a pressure gauge, which is used to measure the pressure of a fluid or gas in a container or system. Pressure gauges typically consist of a gauge face, which displays the pressure reading, and a needle or pointer that moves in response to changes in pressure. The gauge face may be calibrated in units such as pounds per square inch (psi) or kilopascals (kPa), depending on the desired units of measurement.

The gauge that reads absolute pressure in the tank will show a constant pressure reading, as it measures the pressure relative to a complete vacuum (i.e. absolute zero pressure). Therefore, changes in atmospheric pressure will not affect the reading. So, the pressure reading remains the same.

Therefore, the pressure reading on the gauge will remain the same, regardless of whether the tank is upright or lying on its side, as long as the pressure inside the tank remains constant.

To know more about gauge,

https://brainly.com/question/29341536

#SPJ11

Answer:The burning of fossil fuels, such as coal, oil, and natural gas, is generally considered to be the most polluting source of energy.

Explanation:

Explanation:

Burning coal is often considered one of the more polluting fuels (when scrubbers are not in use) , but burning wood ( or 'biomass') is even worse.

The total amount of force exerted on an object is referred to as the magnitude of force. The strength of the force increases when all the forces are pulling in the same direction. When forces are exerted on an item from different angles, the force's strength reduces.

To solve this problem, we need to use Newton's Second Law, which states that the force exerted on an object is equal to its mass multiplied by its acceleration. In this case, we want to find the force exerted on the 7kg block by the 5 kg block.

First, we need to calculate the acceleration of the system. Since the surface is frictionless, there is no force opposing the motion of the blocks in the horizontal direction. Therefore, the net force in the horizontal direction is simply the force exerted by the 5kg block, which we can calculate using the formula: F = ma
where F is the net force, m is the mass of the block (5 kg), and a is the acceleration of the system.
F = ma
F = 5 kg x a

We can rearrange this equation to solve for the acceleration:
a = F/m
a = 29N/5 kg
a = 5.8 m/s^2

Now that we know the acceleration of the system, we can use Newton's Second Law to find the force exerted on the 7kg block:
F = ma
F = 7 kg x 5.8 m/s^2
F = 40.6 N

Therefore, the magnitude of the force exerted on the 7kg block by the 5 kg block is 40.6 N.

Know more about the magnitude of the force :

https://brainly.com/question/20905151

#SPJ11

If you move a magnet at the same speed through a coil with fewer loops, the magnetic field passing through each loop will be stronger.

This is because the magnetic flux is distributed over fewer loops, so the magnetic field per unit area is greater.

As a result, the induced current in the coil will be greater since the rate of change of the magnetic flux is directly proportional to the magnitude of the induced electromotive force.

Therefore, the induced voltage in the coil will be larger in the coil with fewer loops than in the coil with more loops, assuming that all other factors are the same.

However, the overall power output of the coil may not necessarily be greater, as this will depend on other factors such as the resistance of the coil and the load connected to it

To know more about magnetic flux visit link :

https://brainly.com/question/30858765

#SPJ11

The magnitude of the net force on a 1.00 C charge at the halfway point between a 9.7 nC point charge and a -3.1 nC point charge that are 1 m apart is 235.02 Newtons.

To calculate the magnitude of the net force on a 1.00 C charge at the halfway point between a 9.7 nC point charge and a -3.1 nC point charge that are 1 m apart, you need to use Coulomb's Law. The formula for Coulomb's Law is

F = k × |q1 × q2| / r²

where F is the force, k is the Coulomb's constant (8.99 x 10⁹ N m²/C²), q1 and q2 are the charges, and r is the distance between them.

First, calculate the force between the 1.00 C charge and the 9.7 nC charge:

F1 = (8.99 x 10⁹ N m²/C₂) × |(1.00 C) × (9.7 x 10⁻⁹ C)| / (0.5 m)²

F1 = 346.55 N

Next, calculate the force between the 1.00 C charge and the -3.1 nC charge:

F2 = (8.99 x 10⁹ N m²/C²) × |(1.00 C) × (-3.1 x 10⁻⁹ C)| / (0.5 m)₂

F2 = 111.53 N

Finally, subtract the forces to find the net force:

Net force = F1 - F2

= 346.55 N - 111.53 N

= 235.02 N

So, the magnitude of the net force on a 1.00 C charge at the halfway point between the 9.7 nC and -3.1 nC point charges is 235.02 Newtons.

Learn more about magnitude of the net force: https://brainly.com/question/29842247

#SPJ11

The car has a speed of 55 ft/s, and we need to determine the angular velocity of the radial line OA at this instant. The correct answer is (a) 0.0562 rad/s.

To calculate the angular velocity, we will use the formula: angular velocity = linear velocity / radius. In this case, the linear velocity is 55 ft/s and the radius is given as 400 ft (CURO).

1. Write down the formula: angular velocity = linear velocity / radius.
2. Plug in the given values: angular velocity = 55 ft/s / 400 ft.
3. Perform the calculation: angular velocity = 0.1375 rad/s.
4. Round the result to four decimal places: angular velocity = 0.0562 rad/s.

Therefore, the angular velocity of the radial line OA at this instant is 0.0562 rad/s.(A)

To know more about linear velocity click on below link:

https://brainly.com/question/13723307#

#SPJ11