The "64Meg x72" specification for the first DIMM indicates that it is a type of registered ECC (Error-Correcting Code) memory module, which is commonly used in servers and high-end workstations.
The "x72" refers to the number of data bits that are stored on the DIMM. In this case, the DIMM stores 64 Megabytes (64Meg) of data per module and uses a 72-bit data path. The extra 8 bits are used for error correction, which helps to detect and correct errors that can occur during data transfer.
The ECC technology adds extra reliability to the memory module, which is essential for critical applications that require high levels of data integrity and uptime.
However, it also increases the cost of the memory module compared to non-ECC memory.
Learn more about computer memory and the notation: https://brainly.com/question/25996355
#SPJ11
Vaults have reinforced concrete walls, ceilings, and floors, and have a hardened steel door:
The use of reinforced concrete walls, ceilings, and floors in vaults is intended to provide extra strength and durability.
This construction method involves adding additional steel bars or mesh to the concrete mix to improve its tensile strength, which makes it more resistant to cracking and breaking under pressure. Similarly, the hardened steel door is designed to withstand significant force or impact, making it virtually impenetrable. Overall, the combination of reinforced concrete and hardened steel makes vaults extremely secure and difficult to breach.
To learn more about vaults click the link below:
brainly.com/question/26255180
#SPJ11
Sizing of small appliance two wire circuits in dwelling units shall be based on a minimum of _______ volt apms per each circuit. 220.52 (a)
Sizing of small appliance two wire circuits in dwelling units shall be based on a minimum of 20 volt-amperes (VA) per each circuit, according to section 220.52(a) of the National Electrical Code (NEC).
This requirement ensures that there is sufficient electrical capacity to power the various small appliances and devices that are commonly used in a typical dwelling unit kitchen, such as microwaves, toasters, blenders, and coffee makers. The NEC also requires that at least two small appliance circuits be installed in each dwelling unit kitchen, and that these circuits be dedicated solely to powering small appliances and not be used for other loads. By providing dedicated circuits with sufficient capacity, the risk of overloading the circuits and causing electrical fires or damage to appliances is reduced, helping to ensure the safety and reliability of the electrical system in the dwelling unit.
Learn more about appliance here:
https://brainly.com/question/27276396
#SPJ11
You are asked to investigate your company’s procedure to make the sheet and identify possible problems. List the manufacturing process steps and likely problem areas for each step.
A general outline of some common steps involved in sheet manufacturing, along with some potential issues that could arise in each step:
How to explain the stepsRaw material selection: This step involves choosing the appropriate materials to use in the sheet manufacturing process. Potential issues in this step could include the availability or quality of the raw materials, or any regulatory requirements related to their use.
Preparation of raw materials: Depending on the type of sheet being manufactured, this step may involve cutting, slicing, or shredding the raw materials. Potential issues in this step could include problems with the machinery used to prepare the materials, or difficulties in maintaining consistency in the size or shape of the prepared materials.
Mixing: In some cases, the prepared raw materials may need to be mixed together before they can be formed into a sheet. Potential issues in this step could include difficulties achieving a consistent mix, or problems with the equipment used to mix the materials.
Forming: This step involves taking the mixed or prepared materials and shaping them into a sheet. Potential issues in this step could include problems with the equipment used to form the sheet, such as mechanical breakdowns or difficulties achieving the desired thickness or shape.
Drying or curing: Depending on the materials used, the sheet may need to be dried or cured in order to achieve its final properties. Potential issues in this step could include difficulties achieving the right temperature or humidity conditions for drying or curing, or problems with the equipment used for these processes.
Finishing: Once the sheet is formed and dried or cured, it may undergo additional finishing processes such as cutting, trimming, or coating. Potential issues in this step could include difficulties achieving a consistent finish, or problems with the equipment used for these processes.
Quality control: Throughout the manufacturing process, quality control measures should be in place to ensure that the sheet meets the required specifications. Potential issues in this step could include problems with the accuracy or reliability of quality control tests, or difficulties in identifying and addressing quality issues.
Learn more about manufacturing on
https://brainly.com/question/13440987
#SPJ1
Designation of a restricted area is the responsibility of the Physical Security Director: True or False?
Answer: True. The designation of a restricted area falls under the responsibility of the Physical Security Director, as they are responsible for ensuring the security of the facility and its assets. By designating certain areas as restricted.
The Physical Security Director can ensure that only authorized personnel have access to sensitive information or high-value assets.
Protective services or physical security cannot be pitted against the information security role inside physical security. This assertion is false.
The CIA triptych must be taken into account when talking about data and information. The CIA trinity is a notion in information security that consists of three components: confidentiality, honesty, and availability. Each component of the system stands for a significant information security goal.
Situational awareness and homeostasis are promoted by security. Without protection, people frequently grow accustomed to their surroundings and fail to detect odd behaviour from nearby workers and residents. Since awareness is a constant process and individuals aspire to behave responsibly, security fosters a positive and proactive culture.
Learn more about physical security here
https://brainly.com/question/29981144
#SPJ11
What term is used when a water utility divides its total operating expenses into the total revenue?
a.) Debt ratio
b.) Operating ratio
c.) Credit ratio
d.) Coverage ratio
The term used when a water utility divides its total operating expenses into the total revenue is the operating ratio. This ratio is an important financial metric used by utilities to measure their efficiency and profitability.
The operating ratio is calculated by dividing the total operating expenses by the total revenue. This ratio provides insight into the efficiency of the utility's operations and can be used to identify areas where cost savings can be achieved. A lower operating ratio indicates that the utility is more efficient in its operations, while a higher operating ratio indicates that the utility is less efficient and may be spending too much on operating expenses.
In the case of a water utility, operating expenses would include items such as labor costs, maintenance expenses, and equipment costs, among others. By monitoring the operating ratio, the utility can ensure that it is operating in a financially sustainable manner while still providing reliable service to its customers.
Learn more about utility here: brainly.com/question/31385674
#SPJ11
What are two features of a physical, star network topology? (Choose two.)
Two features of a physical, star network topology are: 1. Centralized control: In a star topology, all network nodes are connected to a central hub or switch.
This hub or switch controls the communication between the nodes, allowing for centralized management and control of the network.
2. Scalability: A star topology allows for easy scalability, as nodes can be added or removed without affecting the rest of the network. This makes it a flexible option for networks that may need to expand or change over time.
Two features of a physical star network topology are:
1. Central Hub: In a star topology, all devices are connected to a central hub or switch, which manages and controls the network traffic. This central hub is responsible for transmitting data packets between devices on the network.
2. Point-to-Point Connections: Each device in a star network is directly connected to the central hub via individual cables or links. This ensures that if one connection fails, it does not affect the other devices on the network, thus providing greater fault tolerance and easier troubleshooting.
Learn more about network click here:
brainly.com/question/14276789
#SPJ11
5207 - If an airplane is loaded to the rear of its CG range, it will tend to be unstable about its:-Vertical axis- lateral axis-longitudinal axis
If an airplane is loaded to the rear of its CG (center of gravity) range, it will tend to be unstable about its longitudinal axis. This is because the distribution of weight affects the airplane's pitching moment and stability, with the rearward shift of CG increasing the potential for a nose-up pitching tendency.
The longitudinal axis runs from the nose to the tail of the airplane and is the axis around which the airplane pitches (nose up or nose down). If the center of gravity is too far back, it can cause the tail of the airplane to become too heavy, making it difficult to control the pitch of the airplane. This can lead to a dangerous situation where the airplane is difficult to control and may even stall or spin. It is important for pilots to ensure that their airplane is loaded within the proper CG range to maintain stability and safety in flight.
Learn more about gravity here-
https://brainly.com/question/31321801
#SPJ11
What are the requirements for an engineering solution to be successful? (Vocabulary)
To ensure a successful engineering solution, several requirements must be met, the solution must be technically feasible, meaning it can be developed and implemented using existing technology and knowledge.
Secondly, it should be economically viable, meaning the costs associated with designing, building, and operating the solution are justifiable by the benefits it provides. Thirdly, it should meet the intended purpose and performance requirements, which means it must effectively address the problem it was designed to solve. Additionally, the solution must be safe and reliable, meeting all relevant safety standards and regulations.
Finally, it should be sustainable, considering its environmental impact and the long-term viability of the solution. By meeting these requirements, an engineering solution can be considered successful.
Learn more about engineering solution: https://brainly.com/question/28321052
#SPJ11
Question 86
Biological safety equipment includes
a. Biosafety cabinets
b. Needles and syringes
c. Disinfecting chemicals
d. Technical manuals
Biological safety equipment includes biosafety cabinets, which provide a sterile and enclosed workspace for working with biological agents. Needles and syringes are medical tools and not specifically related to biological safety equipment. Disinfecting chemicals may be used in biological safety procedures but are not equipment. Technical manuals are informative resources but not physical equipment for safety measures.
Biosafety cabinets These are enclosed workspaces designed to provide a controlled environment for handling hazardous biological materials, such as infectious agents. They help to protect laboratory workers and prevent the release of harmful substances into the surrounding environment.Biological safety equipment refers to specialized tools and protective measures used in laboratory settings to ensure the safe handling of biological materials.
learn more about Biosafety cabinets here:
https://brainly.com/question/26248212
#SPJ11
Percent defects in services and purchased materials is typically a measure of supply chain performance for which core​ process?
The percent defects in services and purchased materials is typically a measure of supply chain performance for the Quality Management core process. This process focuses on maintaining high standards and reducing defects in products and services throughout the supply chain.
Percent defects in services and purchased materials is typically a measure of supply chain performance for the core process of quality control and assurance. This process is critical in ensuring that all materials and services purchased by the organization meet the required standards and specifications, and that they are free from defects or errors that could impact the overall quality and performance of the end product or service. By monitoring and measuring the percent defects in the supply chain, organizations can identify areas for improvement and implement corrective actions to optimize their operations and enhance customer satisfaction.
Learn more about management here-
https://brainly.com/question/14523862
#SPJ11
What is the primary reason to subnet IPv6 prefixes?
Explanation:
The primary purpose of subnetting IPv6 address space is to improve address allocation efficiency by subnetting a segment of a network address space.
please make me brainalist and keep smiling dude
(362-10(6) Electrical nonmetallic tubing and fittings shall be permitted to be _____ in a concrete slab on grade where the tubing is placed upon sand or approved screenings.
Answer: Electrical nonmetallic tubing, also known as ENT, is a type of conduit that is used to protect and route electrical wiring in residential and commercial buildings. It is made of a plastic material that is lightweight, flexible, and easy to install. When it comes to installing ENT in a concrete slab on grade, there are specific requirements that must be followed to ensure safety and compliance with building codes.
Explanation:
According to section 362-10(6) of the National Electrical Code, ENT and fittings are permitted to be installed in a concrete slab on grade as long as the tubing is placed upon sand or approved screenings. This means that the tubing must be supported by a layer of sand or other approved material to prevent it from being crushed or damaged by the weight of the concrete.
When installing ENT in a concrete slab on grade, it is important to choose the right type of tubing and fittings for the job. ENT comes in different sizes and thicknesses, so it is important to choose the right size for the wiring being installed. Fittings such as couplings, elbows, and tees must also be selected carefully to ensure a proper fit and to prevent leaks.
Overall, installing electrical nonmetallic tubing in a concrete slab on grade requires careful planning and attention to detail. By following the guidelines set forth by the National Electrical Code and using high-quality tubing and fittings, electricians can ensure a safe and reliable installation that meets the needs of their clients.
Hi! I understand that you would like me to use the terms "Electrical," "tubing," and "200 words" in my response. Here is the answer to your question:
Electrical nonmetallic tubing (ENT) and fittings shall be permitted to be "encased" in a concrete slab on grade where the tubing is placed upon sand or approved screenings.
Step-by-step explanation:
1. Electrical: The term "electrical" refers to the system and components that involve the distribution and use of electricity. In this case, it specifically relates to the nonmetallic tubing and fittings used for electrical installations.
2. Tubing: In this context, "tubing" refers to the electrical nonmetallic tubing, which is a flexible conduit designed to protect and route electrical wiring within a structure. ENT is made from nonmetallic materials, such as PVC, and is often used in concrete slabs on grade.
3. Encased: The term "encased" means that the tubing and fittings are embedded or surrounded by the concrete slab, providing protection and support for the electrical system.
In summary, the code allows for electrical nonmetallic tubing and fittings to be encased within a concrete slab on grade as long as they are placed upon sand or approved screenings, ensuring proper installation and safety.
Learn more about ENT here : brainly.in/question/12742463
#SPJ11
Plants, shrubs, and branches should be cleared away from around an outdoor condensing unit primarily because _______________.
Plants, shrubs, and branches should be cleared away from around an outdoor condensing unit primarily because they can obstruct the airflow and hinder the unit's ability to condense and release heat properly, which can lead to reduced efficiency and potentially cause damage to the unit.
Plants, shrubs, and branches should be cleared away from around an outdoor condensing unit primarily because this ensures proper airflow and prevents debris from obstructing the unit's functionality, thus maintaining its efficiency and prolonging its lifespan.
Learn more about branches here: brainly.com/question/14165530
#SPJ11
(334-15(C)) Where NMC cable is run at angles with joists in unfinished basements it shall be permissible to secure cables not smaller than ____ conductors directory to the lower edge of the joist.
According to the National Electric Code (NEC) section 334.15(C), when NMC cable is run at angles with joists in unfinished basements, it shall be permissible to secure cables not smaller than two conductor's directories to the lower edge of the joist. This means that the cable must be secured to the joist in a way that prevents it from sagging or moving, and it must not be smaller than two conductors in size.
When running NMC cable at angles with joists in unfinished basements, it is permissible to secure cables not smaller than two conductors directly to the lower edge of the joist. Here's the step-by-step explanation:
1. Identify the location: In this case, it's an unfinished basement with joists.
2. Determine the cable type: You mentioned NMC cable, which is a nonmetallic-sheathed cable.
3. Consider the installation method: The cable is run at angles with joists.
4. Check the permissible conductor size: Based on the guidelines, secure cables not smaller than two conductors directly to the lower edge of the joist.
Learn more about NMC cable here: brainly.com/question/31566099
#SPJ11
If there is a rolling straight edge deficiency found on the friction course layer the contractor and the engineer can elect to take a no pay instead of remove and replace. That formula is
The formula for calculating the "No Pay" adjustment for a rolling straight edge deficiency found on a friction course layer is:
No Pay = (Length of deficiency in feet) x (Depth of deficiency in inches) x (Contract unit price per square yard) / 9
The contractor and the engineer have the option of accepting a "No Pay" modification rather than removing and rebuilding the defective portion when a rolling straight edge deficit is discovered on the friction course layer of an asphalt pavement. The No Pay adjustment is determined by the breadth and depth of the deficit as well as the per-square-yard contract unit pricing. The adjustment is determined by using the following equation: No Pay = (Length of Deficiency in Feet) x (Depth of Deficiency in Inches) x (Contract Unit Price per Square Yard) / 9. The reduction in payment that the contractor will receive for the subpar performance is calculated using this method.
learn more about contractor and the engineer here:
https://brainly.com/question/30358104
#SPJ11
A chlorine leak can be detected by?
a. An explosimeter
b. Checking the leak gauge
c. Applying ammonia vapor
d. A tri-gas detector
"A chlorine leak can be detected by a tri-gas detector."
A tri-gas detector is a portable device that can detect the presence of three gases: oxygen, combustible gases, and toxic gases. Chlorine gas is a highly toxic gas that can cause respiratory problems and irritation when inhaled. In industrial settings, chlorine is commonly used as a disinfectant, in the production of chemicals and plastics, and in water treatment processes. In the event of a chlorine leak, a tri-gas detector can quickly alert workers to the presence of chlorine gas in the air, allowing them to evacuate the area or take other appropriate safety measures. An explosimeter is a device used to detect explosive gases and vapors, while a leak gauge is a tool used to measure the amount of gas leaking from a container or pipeline. Applying ammonia vapor can be used to detect leaks in certain types of refrigeration systems, but it is not an effective method for detecting chlorine leaks. Therefore, a tri-gas detector is the most suitable device for detecting a chlorine leak.
Learn more about tri-gas detector here:
https://brainly.com/question/4513701
#SPJ11
Formula for determining the asphalt spread rate for an FC-5 mix?
The asphalt spread rate for an FC-5 mix can be determined using the following formula: Asphalt Spread Rate (in pounds per square yard) = (Mix weight per square yard in pounds) / (% asphalt binder in mix)
To understand this formula, let's break it down into its individual components.
Mix weight per square yard: This refers to the weight of the asphalt mix per square yard of pavement. The mix weight can be calculated by adding up the weight of each component in the mix, including aggregates, asphalt binder, and any additives.
% asphalt binder in mix: This refers to the percentage of the total mix weight that is made up of asphalt binder. For an FC-5 mix, this percentage is typically around 5%.
By dividing the mix weight per square yard by the % asphalt binder in the mix, we can calculate the amount of asphalt binder needed to cover one square yard of pavement at the desired thickness. This result is expressed in pounds per square yard and represents the spread rate of the asphalt mix.
It's important to note that the asphalt spread rate will vary depending on the desired thickness of the pavement layer and the specific properties of the asphalt mix being used. Therefore, it's essential to consult with a qualified engineer or asphalt supplier to determine the appropriate mix design and spread rate for your particular project.
Learn more about asphalt mix here:
https://brainly.com/question/20039044
#SPJ11
A subsystem of the emergency system consisting of feeders and branch circuits is a _____________.
517.2
A subsystem of the emergency system consisting of feeders and branch circuits is defined as an "Emergency Lighting and Power System" in accordance with the National Electrical Code (NEC) section 517.2.
In an automatic emergency lighting and power system, the emergency power source takes over when the ship's service power and lighting plant's potential drops, supplying electricity to the emergency loads.
Emergency lighting is used to provide light in case of a power outage or other disruption to the main power source. A fire or a power outage may cause the loss of mains electricity.
What is the power source for the emergency lights?
Emergency lighting is connected to the building's electrical system so that internal batteries can be continuously recharged to provide backup power for the lighting. This makes sure that during a power loss, the lights stay on, enabling building residents to find the exits with ease in the event that they need to escape.
To know more about Power System, click here:
https://brainly.com/question/28528278
#SPJ11
10. What device forwards data and operates at three of the transmission control protocol internet protocol TCP IP model?A. SwitchB. ClientC. RouterD. Hub
C. Router. The router device forwards data and operates at three of the transmission control protocol internet protocol TCP IP model.
A router is a networking device that functions at the Network layer, Data Link layer, and Physical layer of the TCP/IP paradigm. It examines destination IP addresses to decide which network interface to use for packet forwarding and utilizes routing tables to establish the optimum route for moving data packets between networks. Data is sent between devices connected to the same network using MAC addresses at the Data Link layer, and between networks and devices using physical network interfaces at the Physical layer. Routers are essential to network components that provide quick and safe data transfer between networks and devices.
learn more about TCP IP model here:
https://brainly.com/question/30544746
#SPJ11
How many notches does a DDR 3 DIMM have?
A DDR3 DIMM (Dual In-line Memory Module) typically has 240 notches, which are the small notches on the connector edge of the module.
What is DDR3 DIMM?A DDR3 DIMM (Double Data Rate 3 Dual In-Line Memory Module) is a type of RAM module used in computers and other electronic devices to store data.
DDR3 DIMMs have a single notch located near the center of the module's bottom edge, which is used to differentiate it from other types of memory modules like DDR2 and DDR4, which have their notches in different positions.
This notch ensures compatibility with the correct motherboard slot and prevents incorrect installation. The DDR3 DIMM's increased speed and efficiency compared to its predecessors make it a popular choice for modern computer systems.
Learn more about DDR3 DIMM at
https://brainly.com/question/31567299
#SPJ11
When plate electrodes are used for grounding, each electrode shall be expose a minimum of _____ of surface to exterior soil.
250.53(7)
According to the National Electrical Code (NEC) section 250.53(7), when plate electrodes are used for grounding, each electrode shall be exposed to a minimum of "2 square feet" of surface area to exterior soil.
Grounding is the process of connecting electrical equipment or systems to the earth, or to a conductor that is connected to the earth, for safety and functional purposes. Grounding helps to protect people and equipment from electrical shocks by providing a low-resistance path for electrical current to flow to the earth. It also helps to reduce electrical noise and interference in electronic equipment by providing a stable reference point for electrical signals. Proper grounding is an essential part of electrical safety and is required by building codes and regulations. Grounding can be achieved through a variety of methods, including grounding rods, grounding plates, and grounding wires. It is important to follow proper grounding procedures to ensure the safety and proper functioning of electrical systems.
Learn more about grounding here:
https://brainly.com/question/30242004
#SPJ11
How is an X-ray burst (in an X-ray binary system) similar to a nova?
Both result in the complete destruction of their host stars.
Both are thought to involve fusion of hydrogen into helium.
Both typically recur every few hours to every few days.
Both involve explosions on the surface of a stellar corpse.
While both events involve nuclear fusion reactions, they occur in different types of binary star systems and have different mechanisms for producing the observed phenomena.
None of the options provided is entirely correct. An X-ray burst in an X-ray binary system and a nova are both types of astronomical events, but they are not similar in all the ways listed. An X-ray burst is a sudden, intense burst of X-ray radiation that occurs in some X-ray binary star systems. These systems consist of a neutron star or a black hole in close orbit with a companion star. The X-ray burst is thought to occur when matter from the companion star accumulates on the surface of the neutron star and undergoes a runaway nuclear fusion reaction, resulting in the emission of a burst of X-rays. A nova, on the other hand, is a sudden, temporary brightening of a star that occurs in a binary star system consisting of a white dwarf and a companion star. In a nova, material from the companion star falls onto the surface of the white dwarf, causing a nuclear fusion reaction that releases a large amount of energy and produces a sudden increase in brightness.
Learn more about fusion reactions here:
https://brainly.com/question/31461203
#SPJ11
(250-146(A)) Equipment bonding jumper shall be used to connect the grounding terminal of a grounding-type receptacle to a grounded box. Where the box is surface mounted, direct metal to metal contact between the device yoke and the box shall be permitted to ground the receptacle to the box.(True/False)
True. When a grounded box is surface-mounted, the receptacle may be grounded to the box by making direct metal-to-metal contact with the device yoke. The grounding terminal of the receptacle should still be connected to the box via an equipment bonding jumper, though.
According to the National Electrical Code (NEC) section 250-146(A), an equipment bonding jumper must be used to connect the grounding terminal of a grounding-type receptacle to a grounded box. This is necessary to provide a low-impedance path for fault current and to ensure proper grounding of the receptacle. However, in cases where the box is surface mounted, direct metal-to-metal contact between the device yoke (the metal frame surrounding the receptacle) and the box is also permitted to ground the receptacle to the box. This is because the surface-mounted box is already grounded due to its connection to the building's electrical system. Nonetheless, the use of an equipment bonding jumper is still recommended to ensure a reliable and safe ground connection.
Learn more about Receptacle Bonding Requirements here.
https://brainly.com/question/23839796
#SPJ11
The accumulated time of a TOF timer is reset by causing the ring to go true momentarily. true/false
The statement "The accumulated time of a TOF (Timer Off-Delay) timer is reset by causing the ring to go true momentarily" is true because, In a TOF timer, the accumulated time is the time that has elapsed since the timer's input signal turned off.
The timer starts counting down when its input signal goes from true to false. During the countdown, if the input signal becomes true again momentarily, the accumulated time of the TOF timer will be reset. This means that the timer starts its countdown all over again from the preset time value once the input signal goes back to false.
This reset feature allows the timer to be flexible in its operation, enabling it to adapt to changes in the input signal and maintain the desired off-delay time. In practical applications, this can be useful in cases where the input signal may experience fluctuations or intermittent changes before the actual need for the output action occurs.
In summary, the accumulated time of a TOF timer is reset by causing the input signal to momentarily go true, ensuring that the timer maintains the desired off-delay time and adapts to changes in the input signal.
You can learn more about input signals at: brainly.com/question/31044123
#SPJ11
Question 79
What is the horizontal part of the stairs you step on called?
a. Riser b. tread
c. Step
d. Footer
The horizontal part of the stairs you step on is called the "tread". The tread is the part of the stair that provides a flat surface for you to step on as you ascend or descend the stairs.
Stairs are a common feature in architecture and are used to provide access between different levels of a building. They are typically made up of a series of treads and risers that are arranged in a vertical sequence. Stairs can be constructed using a wide range of materials, including wood, metal, concrete, and stone, and can be designed to match the style of the building they are located in. Stair design is an important consideration in building construction, as it must provide a safe and comfortable means of accessing different levels of the building. Stairs must also comply with building codes and safety standards to ensure that they are structurally sound and safe to use.
Learn more about the stairs here:
https://brainly.com/question/28720025
#SPJ11
Class II locations are those tha are hazardous because of the presence of ________________.
500.5 (C)
According to the National Electrical Code (NEC) 500.5(C), Class II locations are those that are hazardous because of the presence of combustible dust.
Class II locations are those that are hazardous because of the presence of combustible dusts. This is defined in section 500.5 (C) of the National Electrical Code (NEC). Combustible dusts can ignite and cause fires or explosions if they are not properly managed and controlled. Examples of materials that can create combustible dusts include grain, sugar, metals, and plastics. Special electrical equipment and wiring methods are required in Class II locations to prevent sparks and arcs from igniting the dust.
Learn More about National Electrical Code here :-
https://brainly.com/question/17215290
#SPJ11
As a minimum, what technology can be an inexpensive redundant storage option for thick clients?A.RAID 6B.RAID 5C.RAID 1D.RAID 0
For thick customers, RAID 1, commonly referred to as mirroring, might be a cheap redundant storage solution. It includes mirroring the data over two hard drives to provide redundancy in the event of disc failure.
RAID 1, also known as mirroring, can be an inexpensive and simple solution for providing redundancy in storage for thick clients. It involves using two hard drives where one drive mirrors the other, creating an identical backup of the data. This means that if one drive fails, the other can continue to function seamlessly without any data loss or downtime. While RAID 1 provides redundancy, it is important to note that it does not increase performance or capacity, as the mirrored backup uses the same amount of storage as the primary drive. Nonetheless, RAID 1 remains a popular choice for users seeking an inexpensive and reliable way to safeguard their data.
Learn more about RAID 1 for Thick Clients here.
https://brainly.com/question/14669307
#SPJ11
Receptacles incorporating an isolated grounding connection shall be identified by an _________ triangle located on the face of the receptacle.
406.3(d)
Receptacles incorporating an isolated grounding connection shall be identified by an orange triangle located on the face of the receptacle. This is required by code section 406.3(d).
The purpose of this identification is to ensure that users are aware of the presence of an isolated grounding connection and use it properly for electrical safety.Yes, that is correct. Receptacles incorporating an isolated grounding connection shall be identified by an equilateral triangle located on the face of the receptacle. This triangle shall be a green color and shall be located at the bottom of the receptacle opening where visible after installation. (Reference: NEC 2017, Article 406.3(D))
To learn more about receptacle click the link below:
brainly.com/question/28215225
#SPJ11
Using public set methods provides data integrity if:
a. a. The instance variables are public.
b. b. The instance variables are private.
c. c. The methods perform validity checking.
d. d. Both b and c.
Using public set methods to access and modify instance variables that are private ensures that the data integrity of the object is maintained.
Using public set methods to access and modify instance variables that are private ensures that the data integrity of the object is maintained. This is because private instance variables cannot be accessed or modified directly from outside the class, and therefore can only be accessed or modified through the public set methods. Additionally, if the set methods perform validity checking on the data being set, this further ensures that the object's data remains consistent and valid.
Learn more about data integrity here
https://brainly.com/question/31076408
#SPJ11
Except for specially designed recessed fixtures, thermal insulation is not permitted within _______ inches of a lighting fixture, enclosure, wiring compartment or ballast.
410.104(b)
"Except for specially designed recessed fixtures, thermal insulation is not permitted within 3 inches of a lighting fixture, enclosure, wiring compartment, or ballast."
The National Electrical Code (NEC) specifies in section 410.104(b) that thermal insulation should not be placed within 3 inches of a lighting fixture, enclosure, wiring compartment, or ballast. This is because such insulation can trap heat generated by the fixture or its components, leading to overheating and potentially causing a fire hazard. However, specially designed recessed fixtures are an exception to this rule, as they are specifically designed to accommodate insulation without causing a fire hazard. It is important to adhere to this code to ensure the safety of the building and its occupants.
Learn more about thermal insulation here:
https://brainly.com/question/27932945
#SPJ11