Answer:
Explanation:
Work, U, is equal to the force times the distance:
U = F · r
Force needed to lift the weight, is equal to the weight: F = W = m · g
so:
U = m · g · r
= 20.4kg · 9.81 [tex]\frac{N}{kg}[/tex] · 1.50m
= 35.316 [tex]\frac{N}{m}[/tex]
= 35.316 W
when the electrical connection to the alternator from the battery is not tight, it can cause?
Answer:
affects the flow of electricity
Explanation:
A loose battery terminal affects the flow of electricity. There is less power going to the electrical systems and the vehicle will not start or start sluggishly. Also, a loose battery terminal causes the car's electrical components like navigation, car lights, and audio among others to dim or fail completely.
Presents the relevant parameters to be kept in mind when using the following types of motors: 1. AC induction motor 2. BLDC motor 3. Synchronous motor
Answer:
Presents the relevant parameters to be kept in mind when using the following types of motors: 1. AC induction motor 2. BLDC motor 3. Synchronous motorn
Explanation:
sorry
Answer: Hepatitis A
Explanation:
nagdudulot ng pamamaga ng atay
In a shear cutting process, a sheet of soft cold-rolled steel has a thickness of 2 mm and a width of 1 m. The yield strength and the tensile strength is 175 MPa and 300 MPa, respectively. The clearance allowance value for the steel is 0.06. Determine the cutting force in N
true/False
1.
Around 50 percent of all sales of farm commodities are from dairy
products.
Answer:true
Explanation:
It is true that around 50 percent of all sales of farm commodities are from dairy products.
What are dairy products?Dairy products or milk products, also known as lacticinia, are milk-based foods.
Cows, water buffalo, nanny goats, and ewes are the most common dairy animals. Dairy products include common grocery store foods such as yogurt, cheese, and butter in the Western world.
Milk, yogurt, cheese, lactose-free milk, and fortified soy milk and yogurt are all part of the Dairy Group. The Dairy Group excludes milk-based foods with low calcium and a high fat content. Cream cheese, sour cream, cream, and butter are all examples of this.
Dairy products account for roughly half of all farm commodity sales.
Thus, the given statement is true.
For more details regarding dairy products, visit:
https://brainly.com/question/1431669
#SPJ2
Do the coil resistances have any effect on the plots?
a storage tank contains liquid with a density of 0.0361 lbs per cubic inch. the height of liquid in the tank is 168 feet. what is the pressure of the liquid at the bottom of the tank give your answer in psi
Answer:
Objects that float on water have densities less than the density of water; those that do not float on water have densisties greater than the density of water:
Float on water: d < 0.0361 lb/in³ (where d denotes denisity)
Do not float on water: d > 0.0361 lb/in³
Explanation:
I don't know if this works for it or not?
I want to know if anyone else know how to tell apart real leather from fake leather?!?!
Answer:
yes i do.
Explanation:
it's pretty easy in my opinion but i dont know about you why do you ask?
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3 /s is to occur in the cast iron pipe
The water surface elevation must be 110.2631 meters for a flow of 0.03m³ to occur in the cast pipe
For cast iron the chart has 0.0012 from Moody's chart
0.016 for cast iron
[tex]hf = \frac{flQ^{2}}{12.1d5}[/tex]
[tex]h1 = h2+\frac{Q^{2} }{12.1} [\frac{0.0012*100}{(12/1000)^5} +\frac{0.0016*150}{(15/100)^5} ][/tex]
[tex]h1 = 110m+\frac{0.03^2}{12.1} [\f\frac{0.12}{0.00032} +\frac{0.24}{0.000759} ]\\\\h1 = 110+0.0000744[375+3162.06]\\\\= 110 + 0.2631m\\\\= 110.2631m[/tex]
Therefore the water surface elevation must be 110.2631 meters for a flow of 0.03m³ to occur in the cast pipe
Read more on https://brainly.com/question/14081661?referrer=searchResults
why people act like that
Answer:
i dob't know
Explanation:
Beyond providing a visual representation of an object for the creator, what are the advantages of using CAD software to create 3D digital models of engineering prototypes (compared to physical drawings)? Identify at least two advantages.
Answer:
fasdfsd
Explanation:
fsasdf
Explain mathematically whether the divergence of the curl of a vector field is
solenoidal or not?
Answer:
yes
Explanation:
why the power factor is Low in no load test in induction motor ?
The reason for low power factor in no load test in induction motor is high rotor reactance at lower loading since the rotor reactance value gets decreased with increased loading on induction motor
Usually at no load, the Cosine of the phase angle between the stator current(I1) and the stator applied voltage(V1) is the power factor of an induction motor.
In conclusion, the reason for low power factor in no load test in induction motor is high rotor reactance at lower loading since the rotor reactance value gets decreased with increased loading on induction motor
Read more about induction motor
brainly.com/question/1049516
Tech A says that the stoichiometric ratio is 14.7 gallons of air to 1 gallon of fuel. Tech B says it is 14.7 lb of air to 1 lb of fuel. Who is correct
The person that is correct as regards statement made about stoichiometric ratio is; Tech B
In air-fuel mixture, when there is a mix air and fuel in the ideal amounts to make an engine to run efficiently,the ideal ratio of air to fuel is known Stoichiometric ratio.
This stoichiometric ratio is the comparison between the weight of the air relative to the weight of the fuel that it has been mixed with.
Now, weight is in lb and as such, tech B is correct because his ratio is 14.7lb to 1 lb.
Read more at; https://brainly.com/question/16971089
Answer:
Tech B
Explanation:
I took the test and got it right
To find the quotient of 8 divided by 1/3, multiply 8 by?
i need it asap but its should be 1 2 3 or 4 to answer
DONT GIVE ME LINKS ITS STUIPID JUST SAY A B C OR D
Answer: 8.33333333 or 6.1989778
Explanation:
why different types of
engines used gas turbine give reasons
Answer:
Four types of gas turbine engines are used to propel and power aircraft. They are the turbojet, turbofan, turboprop, and turboshaft.
Answer:
A gas turbine, also called a combustion turbine, is a type of continuous and internal combustion engine. The main elements common to all gas turbine engines are: ... Gas turbines are used to
Explanation:
Dilute countercurrent immiscible extraction
A feed of 100.0 kg/min of a 1.2 wt % mixture of acetic acid in water is to be extracted with 1-butanol at 1 atm pressure and 26.7°C, we desire an outlet concentration of 0.1 wt % acetic acid in the exiting water. We have available solvent stream 1 that is 44.0 kg/min of pure 1-butanol and solvent stream 2 that is 30.0 kg/min of 1-butanol that contains 0.4 wt % acetic acid. Devise a scheme to do this separation, find the outlet flow rate and concentration of the exiting 1-butanol phase, and find the number of equilibrium contacts needed.
In Example we assumed that we were going to use all of the solvent available. There are other alternatives. Determine if the following alternatives are capable of producing outlet water of the desired acetic acid concentration.
a. Use only the pure solvent at the bottom of the extractor.
b. Mix all of the pure and all of the impure solvent together and use them at the bottom of the column.
c. Mix all of the pure and part of the impure solvent together and use them at the bottom of the column.
Describe three differences between liquids and gases in fluid power systems.
Answer:
Liquids have less force of attraction between molecules than solids and more than gases; gases have a very weak force of attraction between the molecules which is the least amongst the three states of matter.
Explanation:
The first three terms of a geometric series are 15,7.5 and 3.75. find the representation of the n th term of tge sequence
Answer:
30 1/2
Explanation:
Hierarchy of hazard control
Answer:
A system for controlling risk in the workspace.
how long did it take you to answer all of these questions
Answer:
not sure
Explanation:
not sure
-. Which format is correct for entering dimensions in an architectural drawing?
a
50 12"
b. 4'212"
C.
4' 2.5"
d.
50.5"
Answer:
d.
50.5" is the answer for this question
Let be the step response of the LTI system of impulse response (meaning the output of this system when its input is the unit step sequence). What is the limit of when goes to
Consider an FSM with 1024 states and a 2-bit input (00, 01, 10, 11). How many flip-flops will you need to construct the FSM
Answer:
468
Explanation:
effects of salinity water on alfalfa
ai lm dc bài tập môn cơ học vật liệu ko ạ
Answer:
What's that
Explanation:
Please brainlest me
The Web and Digital Communications pathway is broken down into four main categories of technology. Which category BEST describes Aaden's use of digital communication technology in the following example?
Aaden has created an advertisement that he plans to post on his website and various social media sites to promote his ski shop.
A.
Education
B.
Entertainment
C.
Information
D.
Marketing
How to calculate total photon flux incident on the photodiode
Answer:
Use this PDF file it should help you calculate total photon flux incident on the photodiode.
Explanation:
It's a file on lecture notes that help people learn about engineering and maybe in the lecture notes it might have information about how to calculate total photon flux incident on the photodiode