Fill in my blanks

Mass - measured in ____ or tells the amount of matter in an object.

Volume - the amount of ____ that’s an odject _____ _____

The glassware that must be used when preparing a dilute solution of known concentration from a stock solution of higher concentration is (F) graduated pipet and volumetric flask.

A graduated pipette is a pipette that has the volume marked along the tube in increments. It is employed to precisely quantify and transfer a liquid volume between containers. It has a tapering tip and is composed of glass or plastic tubes. Graduation markings along the tube's body show the capacity from the tip to certain points.

Volumetric flasks, also known as graduated flasks or measuring flasks, are pieces of laboratory glassware or plasticware that are calibrated and labeled to contain a particular volume of reagents, solvents, or any other liquids. Other names for volumetric flasks are measuring flasks and graded flasks. Chemical solutions are frequently made using volumetric flasks.

You can also learn about volumetric flasks from the following question:

https://brainly.com/question/19517011

#SPJ4

The radiation dosage in rads for a 65 ‑kg person that is exposed for 4.0 s to a 3.0 Ci source of beta radiation is 8.54 x 10⁻⁴ J/kg.

Radiation is defined as the energy that can be depicted as waves or particles and travels from one location to another. The DNA in our cells can be harmed by radiation.

The radiation dosage is determined by the ratio of the total dose to the exposed person's mass.

3 Ci beta radiation = 3 x (3.7x10¹⁰) = 11.1 x 10¹⁰decay/s.

Total beta energy taken in over 5 seconds

Et  = ( 11.1 x 10¹⁰ ) x 5 x 1.0 x 10⁻¹³

Et = 55.5 x 10⁻³

The person's radiation dose is estimated as follows;

Rd = ET / m

Rd = 55.5 x 10⁻³ / 65 kg

Rd = 8.54 x 10⁻⁴ J/kg.

Thus, the radiation dosage in rads for a 65 ‑kg person that is exposed for 4.0 s to a 3.0 Ci source of beta radiation is 8.54 x 10⁻⁴ J/kg.

To learn more about radiation, refer to the link below:

https://brainly.com/question/13934832

#SPJ1

H, S8(monoclinic), as well as Methane are the appropriate responses (g). For these three chemicals, overall enthalpy of production is not zero.

Entropy is the quantity of inherent disorder within a substance, whereas enthalpy is the quantity of internal energy. Enthalpy is greater than 0 for water since it is equal for elemental compounds like hydrogen gas and gaseous oxygen (regardless of phase).

Enthalpy with internal energy vary primarily in that internal energy is the total of a system's both potential and kinetic energy, whilst enthalpy is indeed the heat absorbed is evolved through chemical processes that take place in a system.

To know more about enthalpy visit:

https://brainly.com/question/13996238

#SPJ4

Two substituents are taken out of the reactant molecule in an elimination reaction to create the product.

In a one- or two-step method, two substituents are eliminated from a molecule in an organic reaction known as an elimination reaction. Atoms are eliminated as molecules and compounds during an elimination reaction. Two substituents are taken out of the reactant molecule in an elimination reaction to create the product. A metal, an acid, or a base typically catalyze elimination. E1 and E2 reactions are the two primary categories of elimination processes in organic chemistry. Both E1 and E2 processes are also known as alcohol elimination reactions and alkyl halide elimination reactions, respectively. Any organic chemical reaction known as an elimination reaction in which two atoms and groups of atoms are eliminated.

Learn more about molecule

https://brainly.com/question/21263612

#SPJ4

a. Around 0.50g would be left in the sample after 25 years.

How long will it take the initial sample to decay to half of its original amount?

What is isotope?

Give an example of isotope?

To know more about isotopes checkout this link:

https://brainly.com/question/364529

#SPJ4

Sodium reacts faster, producing enough heat to melt itself and occasionally ignite the hydrogen gas, resulting in the characteristic yellow-orange flame of sodium. The potassium reacts violently, bursting into a flame with the typical violet color of potassium.

Potassium has the chemical symbol K and the atomic number 19. Potassium is a silvery-white metal that can be cut with a knife with little effort. In seconds, potassium metal reacts with atmospheric oxygen to form flaky white potassium peroxide.

Sodium and potassium, for example, react violently with cold water. These are exothermic reactions. The reaction is so violent and exothermic that the hydrogen produced instantly catches fire.

Thus,  The potassium reacts violently, bursting into a flame with the typical violet color of potassium.

To learn more about potassium, follow the link;

https://brainly.com/question/13321031

#SPJ1

Answer: [tex][\text{OH}^{-}}]=10^{-6.92} \text{ M}[/tex]

Explanation:

[tex]\text{pH}+\text{pOH}=14\\\\7.08+\text{pOH}=14\\\\\text{pOH}=6.92\\\\\\\text{pOH}=-\log([\text{OH}^{-}}])\\\\6.92=-\log([\text{OH}^{-}}])\\\\[/tex]

[tex][\text{OH}^{-}}]=10^{-6.92} \text{ M}[/tex]

The mass of the oxygen that is formed from the decomposition of the aluminium chlorate is 27.4 g.

We define a decomposition reaction as the kind of reaction that involves the break up of a substance so as to obtain the components of the substance.

The compound that is being broken up can be shown in the equation that we have below;

2Al(ClO₃)₃ → 2AlCl₃ + 9O₂

Thus

Number of moles of aluminum chlorate = mass/ molar mass

= 52 grams /277 g/mol

= 0.19 moles

If 2 moles of aluminum chlorate would form 9 moles of oxygen

0.19 moles of aluminum chlorate would form 0.19 moles * 9/2

= 0.855 moles

Mass of the oxygen = 0.855 moles * 32 g/mol

= 27.4 g

Learn more about reaction:https://brainly.com/question/28984750

#SPJ1

In order for 20 mL of 0.20 M KMnO4 solution to completely react, 3 m.mol of chlorite anion are needed. by a redox process.

Reduction

MnO−4+4H++3e−→MnO2(s)+2H2O(l) I (i)

Oxidation ClO2 + 2 H2 O + ClO4 + 4 H + 4 e (ii)

Overall

4×(i)+3×(ii)4MnO−4+3ClO−2+4H+→4MnO2(s)+3ClO−4+2H2O(l)

Moles of KMnO4 equal 20 10 3L, 0.20 mol, and 1 = 4.0 10 3mol.

According to the equation, we require 3/4 equiv (or 4.0 10 3 mol) of chlorite anion.

Molarity (M), which is determined by dividing the solute's mass in moles by the volume of the solution in liters, is the most widely used unit to express solution concentration: liters of solution/moles of solute equals M. One liter of a solution with a 1 molar concentration (1.00 M) contains 1.00 moles of solute.

Moles of solute divided by kilograms of solvent equals molality. Adding moles of a solvent = 3 and mass of solvent = 0.5 kg , we obtain molality = 3 / 0.5 = 6 mol/kg .

Learn more about oxidation here:

https://brainly.com/question/25798412

#SPJ4

Answer:

0.381 mol/L

Explanation:

"Concentration" is another word for Molarity (at least in this context). Molarity (M) is defined as:

M = mol/L

To find the concentration/molarity, you'll need to find the number of moles of iron (III) nitrate divided by the liters of the solution.

1. Convert grams to moles

You first need to calculate the molar mass of iron (III) nitrate, so you can convert the grams to moles. To do this, you add the masses of each atom in the compound (the masses of each atom can be found from the periodic table).

Fe (iron) has a mass of 55.845 g

N (nitrogen) has a mass of 14.007 g

O (oxygen) has a mass of 16 g

(1 x 55.845) + 3(14.007 + (16 x 3)) = 241.88 g/mol

193.9 is iron (III) nitrate's molar mass, so now you can divide the grams you have by its molar mass to get the number of moles.

44.1/241.88 = 0.1823 mol

2. Convert mL to L

There are 1000 milliliters in 1 liter, so you can divide the number of mL by 1000 to get the number of liters.

478/1000 = 0.478 L

3. Calculate Molarity/concentration

M = mol/L

M = 0.1823/0.478

M = 0.381

Exothermic reactions are

1) 2H2+O2 ⇒2H20+Heat

2) 2C2H2+5O2⇒4CO2+2H20+Heat

Endothermic reactions are

3) CH4+Heat ⇒CO+2H2

4) 2CO2+Heat⇒2CO+O2

What are exothermic and endothermic reactions?

Exothermic reactions are those reactions in which energy is released and in endothermic reactions energy is required to proceed the reaction.

1) & 2) are exothermic because energy is released in reaction 3) & 4) are endothermic because energy is required so called endothermic reaction.

For more information about exothermic & endothermic please visit:

https://brainly.com/question/2782285

#SPJ4

Answer: 144.2

Explanation:

Note that [tex]23.0^{\circ}\text{C}=298.0\text{ K}[/tex].

Using the formula [tex]\frac{V_1}{T_1}=\frac{V_2}{T_2}[/tex] yields:

[tex]\frac{2.45}{T_1}=\frac{1.75}{298}\\\\T_1=\frac{298 \times 2.45}{1.75} \text{ K}\\\\T_1=\frac{298 \times 2.45}{1.75}-273^{\circ}\text{C}\\\\T_1=144.2^{\circ}\text{C}[/tex]

Both Saturday's earthquake and the one in 2010 are thought to have been caused by the Enriquillo-Plantain Garden fault system, according to the United States.

The Enriquillo-Plantain Garden fault zone (EPGFZ or EPGZ) is indeed a network of active coaxial left lateral-moving strike - slip faults faults that extends along the southern coast of Hispaniola, the island that is home to Haiti and the Dominican Republic.

As one of Haiti's main plate-bounding fault systems, the Enriquillo-Plantain Garden fault zone is very well known. Initially believed to be the cause of the Mw 7.0 earthquake that struck Port-au-Prince on January 12, 2010, the strike-slip fault is located close to the city.

To know more about Enriquillo-Plantain visit:

https://brainly.com/question/15960054

#SPJ1

Answer:

1.11 grams CaCl₂

**I am aware that this is not one of the answer choices, but I pretty confident that this should be the correct answer according the the given values

Explanation:

To find the mass of CaCl₂ necessary, you need to

(1) convert the volume from mL to L (1,000 mL = 1 L)

(2) calculate the amount of moles (M = moles / L)

(3) convert moles to grams (using the molar mass)

It is important to arrange the conversions/ratios in a way that allows for the cancellation of units. The final answer should have 3 sig figs like the given values.

(Step 1)

  100. mL CaCl₂                  1 L
--------------------------  x  -------------------  =  0.100 L CaCl₂
                                      1,000 mL

(Step 2)

Molarity (M) = moles / volume (L)                 <----- Molarity ratio

0.100 M = moles / 0.100 L                            <----- Insert values

0.0100 = moles                                             <----- Multiply both sides by 0.100 L

(Step 3)

Molar Mass (CaCl₂): 111 g/mol

 0.0100 moles CaCl₂             111 grams
---------------------------------  x  ---------------------  =  1.11 grams CaCl₂
                                                  1 mole

Answer: repel

Explanation: it's not yet known why like charges repel each other, so

but there's your answer, yw.

Answer:

postsynaptic membrane

Explanation:

Hope it helps!

Oxygen isotope analyses of both deep-sea cores and ice cores (from the Greenland ice sheet) indicate that the Pleistocene was characterized by frequent and widespread climate variability.

This included cycles of glacial advance and retreat.

These changes were caused by variations in the Earth's orbit and tilt, affecting the amount of solar radiation received by different parts of the Earth.

The Pleistocene also saw a series of major ice ages, during which ice sheets and glaciers covered most of the Earth's surface. These ice ages were interspersed with shorter, warmer periods called interglacials. During that time, the Earth's climate resembled the present climate.

Read more about Pleistocene at:

brainly.com/question/28102167

#SPJ4

Given chemical equation:

CuSO₄ + 2HI → Cu₂SO₄ + I₂ + H₂SO₄

CuSO₄ + 2HI - reactants (option - b) is correct.

A chemical equation is composed of the "yields" arrow, the "reactants," and the "products" components. Compounds or elements that are required for the reaction and go through chemical change while the reaction is occurring are known as reactants. Yield is typically represented by an arrow in reactions and refers to the ability to "produce" or "form."

Numerous observable factors, such as color change, energy change (such as a rise in temperature or the production of light), gas production, precipitate formation, and changes in physical properties, can be used to detect chemical reactions.

To know more about chemical equation visit:

https://brainly.com/question/28294176

#SPJ1

the main cause of the increase in the amount of co2 in earth's atmosphere over the past 170 years is . increased infrared radiation absorption by the atmosphere increased worldwide fertilizer production increased

the burning of larger amounts of wood and fossil fuels

An extracted and burned fossil fuel[a] is a hydrocarbon-containing substance that naturally originated in the Earth's crust from the remains of extinct plants and animals. Coal, oil, and natural gas are the three primary fossil fuels. Fossil fuels can be used to produce energy, power engines (like internal combustion engines in cars), or supply heat for immediate use (such for cooking or heating). Before burning, some fossil fuels are processed to produce derivatives like kerosene, gasoline, and propane. The anaerobic decomposition of buried deceased animals that contained organic molecules produced by photosynthesis is the source of fossil fuels. [4] The geological process that transforms these elements into high-carbon fossil fuels often takes millions of years.

Learn more about fossil fuel here:

https://brainly.com/question/3371055

#SPJ4

1) The number of moles of the sodium chloride is 0.94 moles.

2) The number of moles of sodium carbonate is 2.4 * 10^-4 moles.

3) The mass of the sodium chloride is  29.25 g.

We know that we can be able to determine the amount of substance and that the unit of the amount of substance is the mole. The mole refers to the elementary entities that we can be able to find in the compound.

We can obtain the number of moles in each of the cases using the formula;

Number of moles = mass/ molar mass

Hence;

For sodium chloride;

55 g/58.5 g/mol

= 0.94 moles

For sodium carbonate;

0.025 g/106 g/mol

= 2.4 * 10^-4 moles

For the mass of the sodium chloride;

Mass = 0.500 moles  * 58.5 g/mol

= 29.25 g

Learn more about number of moles:https://brainly.com/question/14919968

#SPJ1

The electron configuration of Cu²+ ion  - [tex]1s^2 2s^2 2p^6 3s^2 3p^6 3d^9[/tex]

The electron configuration of Co³ + ion - [tex]1s^2 2s^2 2p^6 3s^2 3p^6 3d^6[/tex]

When we are talking about the electron configuration, we are talking about the way that the electron is arranged around the nucleus of the atom. We know that electrons in the atom can be arranged in energy levels in the atom of the element.

We are asked to write here the electron configuration of the copper II ion and that of the cobalt III ion. In either case, we have to know that electrons have been removed from the neutral atom. In the first case, there are two electrons that have been removed while in the second case, there are three electrons that have been removed.

Thus in writing the electron configuration of the specie we have to take into account the number of the electrons that have been lost due to ion formation. Recall that the ground state is the lowest energy state of the chemical specie.

Learn more about electron configuration:https://brainly.com/question/14283892

#SPJ1

Two elements that have the same properties as magnesium are calcium and strontium.

The number of protons in potassium, K = 19

the number of electrons in potassium, K = 19

The number of neutrons in potassium, K = 20

The Periodic Table is a table that arranges the elements in order of increasing atomic number into vertical columns called groups and horizontal rows called periods.

Elements in the same period have the same number of electron shells or energy levels.

Elements in the same group have the same number of valence electrons or outermost shell electrons.

Considering the given data:

The elements in group 1 are sodium, potassium, and rubidium.

The elements in group 2 are magnesium, calcium, and strontium.

The elements in group 3 are scandium and yttrium.

The number of protons, electrons, and neutrons present in an atom of potassium (K) is determined by the atomic number and mass number of potassium.

Atomic number = number of protons

Number of proton = number of electrons in a neutral atom

Number of neutrons = mass number - atomic number

The atomic number of potassium = 19

mass number = 39

number of neutrons = 39 - 19

number of neutrons = 20

Learn more about periods and groups at: https://brainly.com/question/19266854

#SPJ1

Answer:

the new volume of the balloon after 0.50 mol of CO2 is added is 67 L.

Explanation:

To solve this problem, we need to use the ideal gas law, which states that the pressure of a gas is directly proportional to its temperature and number of moles, and inversely proportional to its volume. This relationship can be written as:

PV = nRT

Where P is the pressure of the gas, V is the volume of the gas, n is the number of moles of the gas, R is the ideal gas constant, and T is the temperature of the gas.

In this problem, the pressure, temperature, and number of moles of the gas all remain constant, so we can rearrange the ideal gas law to solve for the volume of the gas:

V = nRT/P

Plugging in the given values, we find that the volume of the gas is:

V = (0.50 mol CO2)(0.08206 Latm/molK)(298 K)/(1 atm)

V = 67 L

The maximum number of moles of Fe could be produced is 0.1 option - A is correct.

The grams to moles formula must be used in order to accurately calculate the number of moles, n, of a substance with a given mass, m, (in grams): M is the material's molar mass, so n = m / M.

According to the periodic table, the molecular mass of iron, to three decimal places, is 55.845 and its elemental symbol is Fe.

Moles = mass/molar mass

Molar mass of Fe = 56

Number of moles of Fe = 8/56

Number of moles of Fe = 0.14moles.

To know more about moles visit:

https://brainly.com/question/2001450

#SPJ1

Naturally occurring minerals in rocks have a visible crystalline structure because they have a definite chemical composition which allows for the atoms arranged within the mineral to be in a specific ordered manner.

This is referred to as a solid material whose atoms are arranged in a highly ordered microscopic structure thereby forming a crystal lattice present on all the sides.

Naturally occurring minerals in rocks have a crystalline structure because  they have a definite chemical composition which permits the atoms to be arranged in a specific ordered manner or fashion thereby making it the correct choice.

Read more about Crystalline here https://brainly.com/question/27940692

#SPJ1

The full question is:

Explain why naturally occurring minerals in rocks have a visible crystalline structure.

A carbon atom's excited-state electrical configuration is 1s2,2s1,2p3, meaning that by absorbing energy, one electron from the 2 s orbital is excited to the 2 p orbital.

According to Hund's rule, the orbital diagram in c is assumed to match the electron configuration of carbon, which is 1s2 2s2 2p2. It is discovered experimentally that a neutral carbon atom's ground state does indeed contain two unpaired electrons.

picture relating to mot chemistry

One electron each is present in the 1-s orbitals of the two hydrogen atoms. Two different ways in which two hydrogen atoms can unite to create a bond are possible. The MO is in the other

Learn more about hybridization on:

https://brainly.com/question/14140731

#SPJ4

The given statement "Does the law of conservation of mass hold true in this case?" is true because the the sum of the masses of A and B is equal to the mass of AB that reacts.

The law of conservation of mass states that mass can neither be created nor destroyed during the course of reactions but can however be converted to other forms during the course of reactions. Following this rule, if AB reacts to produce A and B, the sum of the masses of A and B must be equal to the mass of AB that reacts.

While the silver residue produced is a solid that is easily recoverable, the other two products are gases that could escape into the surrounding atmosphere unless specially collected or if the reaction is conducted in an enclosed space.

Thus, the fact that only 2.16 g of silver residue was formed does not mean that the law of conservation was not supported by the reaction. The remaining mass would be that of the gases that could have escaped during the course of the reaction.

More on the law of conservation of mass can be found here: https://brainly.com/question/13383562

#SPJ1

Answer:

1.3

Explanation:

From the available choices, Heterogeneous combinations make up potting soil.

In heterogeneous blends, we can easily discern between the various components. The soil's components make up a heterogeneous mixture since they don't all have the same physical and chemical properties.

It's a great idea to grow indoor and potted plants in potting soil. It is typically more nutritious and well-balanced for the plants. The phrase "soil heterogeneity" refers to the diversity of soil traits or taxonomic groupings found in a certain area. Potting soil is a heterogeneous mixture since its composition is not homogeneous.

Tap water is uniform and impossible to identify salt particles without the proper equipment since salt virtually completely dissolves into it.

Chlorine gas (Cl) is a component of homogeneous compounds. Potassium and chlorine are a mixture because all of the components are heterogeneous, or separate.

Table salt is a homogeneous mixture. It contains several ingredients, hence it is not a compound.

The only heterogeneous substance would be potting soil since, without the use of specialist equipment, we can see a variety of particles with different sizes, forms, colors, and other properties.

to know more diversity about  visit this:

https://brainly.com/question/7063191

#SPJ1