Answer:
b> infinity
Explanation:
i think b is the correct one
Answer:
(B) Infinity
Explanation:
Gravity can basically never become zero except hypothetically at infinity.
A satellite’s speed is
5,000 m/s. After 1 min, it is 10,000 m/s.
What is the satellite’s acceleration?
Acceleration = (change in speed) / (time for the change)
Change in speed = (10,000 m/s) - (5,000 m/s)
Change in speed = 5,000 m/s
Time for the change = 1 minute
Time for the change = 60 sec
Acceleration = (5,000 m/s) / (60 s)
Acceleration = 83-1/3 m/s²
1. What does Louis de Broglie's principle propose about electrons?
They have energy and momentum.
They behave as a wave and a particle.
They contain high-energy and low-energy photons.
They interact with other electrons to form new substances.
Louis de Broglie's principle of electrons states that (b) They behave as a wave and a particle.
The de Broglie equation is one of the equations that is commonly used to define the wave properties of matter. It basically describes the wave nature of the electron.Electromagnetic radiation, exhibit dual nature of a particle (having a momentum) and wave (expressed in frequency, wavelength). Microscopic particle-like electrons also proved to possess this dual nature property.Louis de Broglie in his thesis suggested that any moving particle, whether microscopic or macroscopic will be associated with a wave character. It was called ‘Matter Waves’. He further proposed a relation between the velocity and momentum of a particle with the wavelength, if the particle had to behave as a wave.Particle and wave nature of matter, however, looked contradictory as it was not possible to prove the existence of both properties in any single experiment. This is because of the fact that every experiment is normally based on some principle and results related to the principle are only reflected in that experiment and not the other.To know more about electrons visit:
https://brainly.com/question/24170350
#SPJ1
The system in the figure below, If atmospheric pressure is 101.3 KPa and the absolute pressure at the bottom of the tank is 231.3 KPa, what is the specific gravity of the olive oil?
If atmospheric pressure is 101.3 KPa and the absolute pressure at the bottom of the tank is 231.3 KPa, the specific gravity of the olive oil is 1.30
How do you calculate the gravity?To calculate the specific gravity, deduct the absolute pressure at the bottom of the tank (231.3 KPa) from the atmospheric pressure (101.3 KPa). This will give you a ratio of 130KPa, then divide it by the atmospheric pressure which is the specific gravity of olive oil.
Use the formula below:
specific gravity = absolute pressure - atmospheric pressure / atmospheric pressure
Specific gravity = (231.3 KPa - 101.3 KPa) / (101.3 KPa) = 1.30
Therefore, the specific gravity of the olive oil is 1.30.
learn more about absolute pressure: https://brainly.com/question/17200230
#SPJ1
If an object is moving and the sum of all the vector forces on it is zero, then the object will:
accelerate at a constant rate
come to rest
move at a constant speed
none of the previous
If an object is moving and the sum of all the vector forces on it is zero, then the object will move at a constant speed. The correct option is c.
What is vector force?A force's magnitude and direction are both represented by a force vector. This contrasts with expressing the force's magnitude alone, which is known as a scalar quantity.
Typically, a vector is represented by an arrow that points in the direction of the force and has a length proportionate to the strength of the force.
Therefore, the correct option is c, move at a constant speed.
To learn more about vector force, refer to the link:
https://brainly.com/question/13492374
#SPJ1
A student collected data about the speed of an object over time.
Which type of graph should the student use to represent the data?
Answer:I have already did this the answer was bar graph!
Explanation:
In a particular crash test, an automobile of mass 1245 kg collides with a wall and bounces back off the wall. The x components of the initial and final speeds of the automobile are 18 m/s and 2.9 m/s, respectively. If the collision lasts for 0.11 s, find the magnitude of the impulse due to the collision. Answer in units of kg · m/s. Answer in units of kg · m/s.
Answer:
Δp=-18799.5kg*m/s
Explanation:
Δv=Vf-Vi
Δv=2.9m/s-18m/s
Δv=-15.1m/s
m*Δv=Δp
1245kg*(-15.1m/s)=Δp
Δp=-18799.5kg*m/s
Extra:
Deriving mΔv=Δp
Δp=Pf-Pi
Δp=m*Vf-m*Vi
Δp=m(Vf-Vi)
Vf-Vi=Δv
Δp=m(Δv) or Δp=mΔv
What are the names and number of of atoms in a molecule of nitrous oxide,N2O?
Answer:
2 nitrogen and 1 oxygen,
Explanation:
N2=2 nitrogen
O= a single element
Concluding statement about electricity like a sentence or two
Things are:
Wind turbines
Hydroelectric
Geothermal heat
Write it in like a concluding statement feel
Wind turbines, hydroelectric, and geothermal heat have been relied upon for decades to provide a renewable and clean energy source to people around the world. These alternative energy technologies provide optimal clean and renewable energy sources for many communities and countries striving for sustainable development.
Rank the images showing the highest electric potential 1 energy to the lowest electric potential energy 4.
Answer:
3rd image, 2nd image, 1st image, 4th image
Explanation:
Not an easy question, tricky one
Electric potential energy is proportional to the magnitude of the charges (the higher the charges, the stronger the Electric potential energy(EPE)) and inversely proportional to the distance between the charges(the longer the distance, the smaller the EPE). U = kQq/r
EPE is positive in this case due to unlike charges.
Between distance and magnitude of the charges, magnitude of charges play a more significant effect than distance (due to Qq , both the magnitude of Q and q affect the EPE)
Hence. zoom in on the magnitude first.
3rd image has the largest + and -, hence greatest magnitude of charges, therefore highest EPE.
Between 1st and 2nd images, charges have the same magnitude, distance now comes to play. Distance between the charges is smaller for image 2 and the charges experience greater EPE. 1st image, the charges are further, hence smaller EPE.
For the fourth image, the magnitude of the charges is the smallest, hence smallest EPE.
A 9.5 kg test rocket is fired vertically from Cape Canaveral. Its fuel gives it a kinetic energy of 2390 J by the time the rocket motor burns all of the fuel. The acceleration of gravity is 9.8 m/s². What additional height will the rocket rise? Answer in units of m.
Answer:
4.95 m
Explanation:
The rocket's initial kinetic energy is equal to the final gravitational potential energy, so we can set these equal to each other and solve for the additional height the rocket will rise:
KEinitial = KEfinal
1/2 * m * v^2 = m * g * h
Substituting the given values, we have:
1/2 * 9.5 kg * v^2 = 9.5 kg * 9.8 m/s^2 * h
Solving for h, we find that the additional height the rocket will rise is h = 2390 J / (9.5 kg * 9.8 m/s^2) = 4.95 m.
a defender running away from a goalkeeper at 5m/s is hit in the back by the goal kick. the ball stops dead and the players speed increases to 5.5m/s if the ball had a mass of 500g and the player mass is 70k how fast was the ball moving?
The goal kick strikes a defender racing at 5 m/s away from a goalkeeper in the back. The ball was moving at a speed of 70 m/s if it weighed 500g and the player's mass was 70k.
Why does the goalie in a football game pull his hands back after holding the ball that has been shot towards the goal?The goalkeeper extends the amount of time he has to hold the ball by pulling his hands back. He lessens the force (rate of change of momentum) the football exerts on him by lengthening the time.
Write the formula for momentum and define it.A vector quantity, momentum. A body's momentum is equal to P=m.v if it is travelling at a speed of v while having mass m. P=mv describes the magnitude of the momentum. Because momentum is a function of mass and velocity, its unit is the product of those two quantities.
By using conservation of momentum,
Initial momentum = Final momentum
(5 x 70) + (v x 0.5) = (5.5 x 70) + (0 x 0.5)
350 + 0.5v = 385 + 0
0.5v = 35
v = 70 m/s
To learn more about Momentum visit:
brainly.com/question/24030570
#SPJ1
The anterior cruciate ligament in a woman's knee is 2.5 cm long and has a cross- sectional area of 0.54 cm2. If a force of 3000 N is applied longitudinally, how much will the ligament stretch? assume that young's modulus (1.8x10¹0 N/m²)
If a longitudinal force exceeding 3000 N is applied. Young's modulus for that object equals DL = 0.0139m.
Which is better, a greater or lower Young's modulus?The greater the modulus, or the lesser elasticity strain that arises from the application of a given stress, the stronger that medium is. Young's modulus, sometimes referred to as mechanical performance, is a metric used to determine how stiff a material is. In other words, it is readily bent or stretched.
Young's modulus really measures a material's ability to withstand changes in length when compressed or under stress along its length. Divide the primary stresses by the strain to get Young's modulus, commonly known also as young's modulus.
Young's modulus Y= stress/strain
= (F/A) /(DL/L)
F=3000N,
A=0.54 cm²,
L=2.5cm,
Y=0.1 Gpa
0.1 * 10⁹ = (3000/(0.54* 10⁻⁴) (2.5 ⋆ 0.01/DL)
DL = 0.0139m
To know more about Young's modulus visit:
brainly.com/question/14458238
#SPJ1
A Ferris wheel, rotating initially at an angular speed of 0.16 rad/s, accelerates over a 8.0-s interval at a rate of 0.040 rad/s2. What is its angular speed after this 8.0-s interval?
Answer:
0.48 rad/s
Explanation:
We can use this equation to find the final velocity
[tex]w_f=w_0+at[/tex]
We are given
[tex]w_0=0.16[/tex]
[tex]t=8.0[/tex]
[tex]a=0.04[/tex]
Inserting those numbers into our equation gives us
[tex]w_f=0.16+0.04*8[/tex]
Lets solve for [tex]w_f[/tex].
[tex]w_f=0.16+0.32[/tex]
[tex]w_f=0.48[/tex]
Question
Stopping Distance
48.0 ft
49.0 ft
50.0 ft
51.0 ft
52.0 ft
2
The stopping distance for 10 cars traveling at 55 miles per hour is shown in the table above. What is the
mean (average) stopping distance for the 10 cars?
Frequency
1
2
3
2
Kam does 4000J of work in climbing a set of stairs. if he does work in 6 seconds, whi is his power output?
Answer:
666.7 W
Explanation:
Power = P = W/t = 4000 J/6 s = 666.7 W (watts)
what is the normal force on a 2000N refrigerator resting on the ground
The perpendicular force that a surface applies to an item is known as the normal force. FN = m ⋅ g
What is Normal force?The perpendicular force that a surface applies to an item is known as the normal force. For instance, if you place a book on a table, a gravitational force will cause it to fall. The table pulls on the book in order to counterbalance this force and keep it from dropping. The normal force, often known as the opposing force, is denoted by the symbols FN F N or NN. "N" stands for the normal force unit (Newton).
A common illustration of Newton's third rule of motion is the normal force.
When one object applies force to another, the other applies a force in the opposite direction and of equal magnitude to the first object (action equals reaction).
Therefore, the force applied by the item to the surface is equal to the normal force. The calculations change according to the surface's slope.
The formula is as follows for an object laying on a flat surface:
FN = m ⋅ g
where
The mass of an object is m.
Gravitational acceleration is denoted by g.
The normal force (FN F N ) for an item on a flat surface is equal to its gravitational force, according to Newton's third law ( WW).
The formula is as follows for an object laying on a flat surface:
To know more about Normal Force refer to:
https://brainly.com/question/13622356
#SPJ1
A student pours a spoonful of dirt into a cup of water. The water and dirt are stirred together. The water turns a light brown color. Some dark pieces float to the top of the cup and another dark layer forms on the bottom of the cup. Which statement BEST describes the contents of the cup?
The statement that is correct is that the contents of the cup form a mixture.
What is the nature of the cup?Though the question is incomplete but I would try to give you a good explanation as much as I can. We must recall that when we talk about a mixture, we have to note that the term mixture would refer to the combination of two or more substances that do not chemically react together.
In this case, we have been told that we have a water that was pure and then we add dirt to it. It is clear that the water and the dirt do not react in any way hence what we have formed is a mixture.
Learn more about mixtures:https://brainly.com/question/24898889
#SPJ1
If a Current Current of strength 3A flows through aresistance of 20 om for 10 minutes,then calculate the amount of heat produced in the resistance.
Answer:
1.08 x 10^5 J
Explanation:
First, apply the formula V = IR , where V is the voltage, I is the current and R is the resistance.
R -> 20 ohm (Given)
I -> 3A (Given)
Hence, V = 3 x 20 = 60V (60 volts)
Next, apply the formula E = Pt , where E is the energy produced, P is the power and t is the time in seconds
Furthermore, since P = IV (power = current x voltage)
The formula can be re-expressed as E = VIt
t -> 10 minutes = 600 seconds (don't forget to convert time to seconds!)
Therefore, energy = (60 x 3 x 600) J
= 108000 J
= 1.08 x 10^5 J (in scientific notation)
Hea produced in the resistance = energy produced in the resistor
= 1.08 x 10^5 J
The reliability or reproducibility of a measurement is its _____
The degree of data stability when the measurement is replicated under identical circumstances is known as reproducibility or reliability.
What exactly are repeatability and reproducibility?Reproducibility determines how an entire study an experiment can be replicated, whereas repeatability assesses the variation in data made by a single equipment or human under similar circumstances.
What makes repeatability crucial?Science needs reproducibility because it enables more in-depth investigation, and replication validates our findings. There are several investigations and experiments, which result in a wide range of variables, unforeseen, and things that are either outside your influence or you cannot guarantee.
To knw more about measurement visit:
https://brainly.com/question/2107310
#SPJ1
A blue whale with a mass of 1.90 X 10^5 kg was caught in 1947. What is the magnitude of the minimum force needed to move the whale along a horizontal ramp if the coefficient of static friction between the ramp's surface and the whale is 0.460?
The minimum force needed to move the whale along a horizontal ramp, given that the whale has a mass of 1.90×10⁵ Kg is 856520 N
How do I determine the force needed to move the whale?We'll begin by listing out the given parameters from the question. This is shown below:
Mass of whale (m) = 1.90×10⁵ KgCoefficient of static friction (μ) = 0.460Force needed (F) = ?To obtain the force needed to move the whale, we shall first obtain the normal reaction. This is shown below:
Mass of whale (m) = 1.90×10⁵ KgAcceleration due to gravity (g) = 9.8 m/s²Normal reaction (N) = ?N = mg
N = 1.90×10⁵ × 9.8
N = 1862000 N
Finally, we shall determine the force needed. Details below:
Coefficient of static friction (μ) = 0.460Normal reaction (N) = 1862000 NForce needed (F) = ?F = μN
F = μN
F = 0.460 × 1862000
F = 856520 N
Thus, we can conclude that the force needed is 856520 N
Learn more about force:
https://brainly.com/question/12163222
#SPJ1
Until 1979, the world's easiest driving test was administered in Egypt. To pass the test, one needed only to drive about 6 m forward, stop, and drive the same distance in reverse. Suppose that at the end of the 6 m the car's brakes are suddenly applied and the car slides to a stop. If the force required to stop the car is 6.0 X 10^3 N and the coefficient of kinetic friction between the tires and pavement is 0.77, what is the magnitude of the car's normal force? What's the car's mass?
(a) The magnitude of the car's normal force is 7,792.2 N.
(b) The mass of the car is 795.1 kg.
What is the weight of the car?
The weight of the car is calculated by applying Newton's second law of motion as shown below.
Mathematically, the formula for Newton's second law of motion is given as;
Ff = μW
where;
W is the weight of the carμ is the coefficient of kinetic friction between the tires and pavementThe weight of the car is calculated as follows;
W = Ff / μ
W = ( 6,000 N ) / ( 0.77 )
W = 7,792.2 N
Based on Newton's third law of motion, the weight of the car acting downwards is equal to normal force on the car, acting upward.
The mass of the car is calculated as follows;
W = mg
where;
m is the mass of the carg is acceleration due to gravitym = W / g
m = ( 7792.2 ) / (9.8)
m = 795.1 kg
Learn more about normal force here: https://brainly.com/question/14486416
#SPJ1
Two carts of equal mass are on a horizontal surface with negligible friction. Cart A is approaching cart B, which is at rest, as shown in Figure 1 above. Attached to cart B is a spring that is initially compressed. At the moment cart A collides with cart B, the spring is released and pushes on cart A, as shown in Figure 2 above. Which of the following correctly states what happens to the kinetic energy and the momentum of the two-cart system as a result of the collision compared to those quantities before the collision?
(A) Kinetic energy: Increases; Magnitude of Momentum: Decreases
(B) Kinetic energy: Increases; Magnitude of Momentum: Stays the same
(C) Kinetic energy: Increases; Magnitude of Momentum: Increases
(D) Kinetic energy: Stays the same; Magnitude of Momentum: Decreases
(E) Kinetic energy: Stays the same; Magnitude of Momentum: Stays the same
The option that correctly states what happen to the kinetic energy and the momentum of the two-cart system as a result of the collision compared to those quantities before the collision is
B) Kinetic energy: Increases; Magnitude of Momentum: Stays the same
What is kinetic energy?The energy an object has as a result of motion is known as kinetic energy. A force must be applied to an object in order to accelerate it. We must put in effort in order to apply a force.
Since the elastic potential energy that was initially stored in the compressed spring has now been converted into kinetic energy, the system's total energy should be conserved. As a result, the system's kinetic energy increases. As a result, the system's kinetic energy rises.
The magnitude of the two-cart system's net momentum remains constant because there is no outside force acting on it, which implies that the system's overall momentum should be conserved.
Therefore, the correct option is B.
Learn more about energy on:
https://brainly.com/question/25959744
#SPJ1
*NOTE* The answers in this question are
NOT realistic. Don't second guess yourself!
A pitcher claims he can throw a 0.151 kg
baseball with as much momentum as a 3.22 g bullet moving with a speed of 1.90312 x
10° m/s.
What must be its speed if the pitcher's claim is valid?
Answer in units of m/s. Answer in units of ms.
004 (part 2 of 3) 1.0 points
What is the kinetic energy of the bullet?
Answer in units of J. Answer in units of J.
005 (part 3 of 3) 1.0 points
What is the kinetic energy of the ball?
Answer in units of J. Answer in units of J
Answer: It is not clear what is the power of 10 in the speed of the bullet but here is a general procedure for the question.
Explanation:
[tex]P_{bullet}=(3.22*10^{-3}kg)*(10^{?}m/s)\\P_{baseball}=P_{bullet}\\[/tex]
Therefore we can write:
[tex](0.151*10^{-3} kg)*v_{baseball}=(3.22*10^{-3}kg)*(10^{?}m/s)[/tex]
From this using the relationship:
[tex]v_{baseball}=\frac{(3.22*10^{-3}kg)*(10^?m/s)}{0.151*10^{-3}kg}[/tex]
I cannot give a precise answer since power of then for speed of the bullet is not clear. But using the above equation you can reach the answer. General form of the equation is therefore:
[tex]v_{baseball}=\frac{P_{bullet}}{m_{baseball}}[/tex]
Where m is the mass of the ball which is 0.151 g.
What does a step-down transformer change in an alternating current?
Answer: A step-down transformer changes the magnitude of the voltage in an alternating current (AC) electrical signal. It reduces the voltage of the AC signal by using a winding ratio between the primary (input) and secondary (output) coils that is less than 1:1.
Explanation: For example, if the winding ratio of a step-down transformer is 1:0.5, the output voltage of the secondary coil will be half the magnitude of the input voltage of the primary coil. In this case, the transformer would change the AC voltage from a higher value to a lower value.
The transformer does not change the frequency of the AC signal, which is determined by the source of the electrical power. The transformer also does not change the waveform of the AC signal, which is typically a sinusoidal wave.
The same 42 kg cart is pushed forward with a force of 180 Newtons. How far will it go if a total of 2500 Joules of work are done on the cart?
Important Formulas:
[tex]w=Fd[/tex]
work(measured in joules) = force(measured in newtons) * distance(measured in meters)
__________________________________________________________
Given:
[tex]m=42kg[/tex]
[tex]F=180N[/tex]
[tex]w=2500J[/tex]
[tex]d=?[/tex]
__________________________________________________________
Rearranging work formula to make distance the subject:
[tex]w=Fd[/tex]
[tex]\dfrac{w}{F} =\dfrac{Fd}{F}[/tex]
[tex]d=\dfrac{w}{F}[/tex]
__________________________________________________________
Finding distance:
[tex]d=\dfrac{w}{F}[/tex]
[tex]d=\dfrac{2500}{180}[/tex]
__________________________________________________________
[tex]\fbox{d = 13.89 meters}[/tex]
What are the horizontal and vertical components of a cat's displacement when the cat has climbed 5 m
directly up a tree © = 90°? Sin90=1
cos90=0
The horizontal component of the cat's displacement, Dx = 0 m
The vertical component of the cat's displacement, Dy = 12 m
What are the horizontal and vertical components of a vector?The horizontal component of a vector is the value of that vector acting in the horizontal direction.
The horizontal component of a vector is given as Dx.
Dx = Dcosθ
where;
D is the resultant of the vector
θ is the angle of the vector from the horizontal
The horizontal component of the cat's displacement is:
Dx = 12 * 0
Dx = 0 m
The vertical component of a vector is the value of that vector acting in the vertical direction.
The vertical component of a vector is given as Dy.
Dy = Dsinθ
where;
D is the resultant of the vector
θ is the angle of the vector from the horizontal
The vertical component of the cat's displacement is:
Dy = 12 * 1
Dy = 12 m
Learn more about horizontal and vertical components at: https://brainly.com/question/26446720
#SPJ1
For science class your teacher gives you and your partner a ball she ask you to figure out a way to Balance forces that you apply to the ball how do you partner show this?
Two forces are said to be balanced when their strengths are equal but their directions of action are opposing.
What is Balanced Force?The forces are balanced if the pullers are exerting equal force but going in the opposite direction on either side of the rope.
Forces that are balanced can cancel one another out. The thing stays in place whenever there is a balanced force.
To lift, turn, move, open, close, push, pull, and many other things requires forces. You apply force to a ball when you throw it in order for it to travel through the air. An object can be under the influence of multiple forces at once.
Therefore, Two forces are said to be balanced when their strengths are equal but their directions of action are opposing.
To learn more about Forces, refer to the link:
https://brainly.com/question/13191643
#SPJ1
An airplane flies from Milwaukee to Chicago, a distance of 130 kilometers, and is in the air for 20 minutes. What is its average velocity? Show your work or explain how you got your answer.
The average velocity of the airplane between Milwaukee and Chicago is 1083.33 meter/second.
What is velocity?The rate at which a body's displacement changes in relation to time is known as its velocity. Velocity is a vector quantity with both magnitude and direction. SI unit of velocity is meter/second.
The total distance between Milwaukee and Chicago = 130 kilometer
= 1,300,000 meter.
Time interval = 20 minute = 20×60 second = 1200 second.
The average velocity of the airplane = total distance/time interval
= 1,300,000 meter / 1,200 second.
= 1083.33 meter/second.
Learn more about velocity here:
https://brainly.com/question/18084516
#SPJ1
The first scientist misidentified the fossil as that of a big cat. What body structure did he use to make his observations?
In velocity time graph of a body, two points are given as A(40,5) and B(20,2). What is the acceleration of the body
Answer:
0.15 m/s²
Explanation:
Acceleration is rate of change of velocity-time function. We can find acceleration by finding the slope. The slope of graph can be found by:
[tex] \displaystyle{a = \dfrac{ \Delta v}{ \Delta t} \: \to \: \dfrac{v_f - v_i}{t_f- t_i}}[/tex]
Substitute in:
[tex] \displaystyle{a = \dfrac{5 - 2}{40 - 20}} \\ \\ \displaystyle{a = \dfrac{3}{20}} \\ \\ \displaystyle{a = 0.15 \: \text{m/s}^{2} }[/tex]
Therefore, the acceleration is 0.15 m/s²