Directions Concept Builder Charge and Charging

Based on the graph provided, we can conclude that the speed of the moving object constantly changes over time.

This can be seen from the fact that the distance traveled by the object is not a straight line on the graph, but rather a curved line that changes direction and slope throughout the plotted time period. Therefore, we can infer that the object's speed is not constant and varies at different points in time.
When analyzing a distance vs. time graph, the slope of the line represents the speed of the object.
1. The speed of the moving object decreases over time: This would be represented by a downward-sloping line (negative slope) on the graph.
2. The speed of the moving object increases over time: This would be represented by an upward-sloping line (positive slope) on the graph.
3. The speed of the moving object constantly changes: This would be represented by a curved or zig-zag line on the graph.
4. The speed of the moving object remains constant: This would be represented by a straight, horizontal line (zero slope) on the graph.

To learn more about speed click here https://brainly.com/question/28224010

#SPJ11

Assuming the resistance is constant, the current in the heating element if it is connected to 120 v is 4.247A

If the temperature and other physical parameters of the wire, such as stresses and strains, stay unchanged, the current flowing through the wire is precisely proportional to the potential difference applied across its ends.

To calculate the current in the heating element when connected to 120 V, we can use the  Ohm's Law formula:
Power (P) = Voltage (V) x Current (I)
We know that the power rating of the heating element is 2,040 W when connected to 240 V. Therefore, we can find the resistance of the heating element using the formula:
Resistance (R) = (Voltage)² / Power
R = (240)² / 2040
R = 28.235 ohms
Now that we know the resistance of the heating element, we can use the formula for current:
I = V / R
When the heating element is connected to 120 V, the current can be calculated as:
I = 120 / 28.235
I = 4.247 A
Therefore, the current in the heating element when connected to 120 V is 4.247 A, assuming the resistance is constant.

Learn more about Ohm's Law here

https://brainly.com/question/14796314

#SPJ11

Meteorologists can distinguish a cold from a warm front because a cold front occurs when a cold air mass advances and replaces a warmer air mass, resulting in cooler temperatures and often stormy weather. On the other hand, a warm front exists where a warm air mass moves over and replaces a cooler air mass, resulting in a gradual increase in temperature and often steady rainfall.

A cold front occurs when a cold air mass advances into a region occupied by a warm air mass. As the cold air mass moves forward, it lifts the warm air mass, causing the warm air to cool and condense into clouds. This can result in the formation of thunderstorms and other types of precipitation, and often brings a rapid drop in temperature.

A warm front, on the other hand, exists where a warm air mass advances into an area occupied by a cooler air mass. As the warm air mass moves forward, it rises over the cooler air mass, causing the warm air to cool and condense into clouds. This can result in the formation of steady rain or drizzle, and often brings a gradual rise in temperature.

In summary, meteorologists can distinguish a cold front from a warm front based on the direction in which the air masses are moving and the temperature characteristics of each air mass.

Learn more about  warm front here:

https://brainly.com/question/21551311

#SPJ11

1) Cold fronts occur when a cold air mass moves into and replaces a warmer air mass.

This typically happens when a high-pressure system moves in, pushing cold air towards an area of low pressure.

2) As the cold air mass moves forward, it forces the warm air mass upwards, where it cools and condenses.

This creates clouds, which can lead to precipitation.

3) The boundary between the two air masses is called a front.

In a cold front, the front is the leading edge of the cold air mass.

4) The cold air behind the front is usually drier and colder than the air ahead of the front.

This can cause a sudden drop in temperature and a change in wind direction, which can result in severe weather conditions such as thunderstorms, strong winds, and even tornadoes.

5) Warm fronts, on the other hand, occur when a warm air mass moves into and replaces a colder air mass.

This typically happens when a low-pressure system moves in, drawing warm air from surrounding areas towards an area of lower pressure.

6) As the warm air mass moves forward, it rises over the colder air mass, where it cools and condenses.

This also creates clouds, which can lead to precipitation.

7) The boundary between the two air masses is again called a front, but in a warm front, the front is the leading edge of the warm air mass.

8) The warm air mass is usually more humid than the air ahead of the front.

This can cause a rise in temperature and a change in wind direction, which can result in milder weather conditions such as light rain, drizzle, or even fog.

By observing the characteristics of a front and the air masses behind it, meteorologists can make predictions about future weather patterns, which helps people prepare for potential weather hazards.

To know more about warm front visit link :

https://brainly.com/question/12375861

#SPJ11

Answer:

Without a specific figure 27.11 provided, I cannot refer to it directly. However, I can provide general information on how to rank the resistances of wires made of the same material.

The resistance of a wire is given by the formula R = (ρL)/A, where ρ is the resistivity of the material, L is the length of the wire, and A is the cross-sectional area of the wire.

To rank the resistances of wires made of the same material, we need to compare the values of (ρL)/A for each wire.

The wire with the largest resistance will have the smallest cross-sectional area (i.e., the thinnest wire) or the longest length, or both.

The wire with the smallest resistance will have the largest cross-sectional area (i.e., the thickest wire) or the shortest length, or both.

The middle wires will have intermediate resistances, depending on their length and cross-sectional area.

It's worth noting that the resistivity of a material can also depend on temperature, so if the wires are at different temperatures, that can also affect their resistances.

Explanation:

The magnitude of the tangential acceleration of a point on the rim of the wheel  is A) zero m/s².

The tangential acceleration (a_t) is calculated using the formula: a_t = r * α where r is the radius of the wheel and α is the angular acceleration. The magnitude of the tangential acceleration of a point on the rim of the wheel can be calculated using the formula a = rα, where a is the tangential acceleration, r is the radius of the wheel, and α is the angular acceleration. Since the question does not provide any information about the angular acceleration, we cannot calculate the tangential acceleration. Therefore, the correct answer is A) zero m/s².

More on acceleration: https://brainly.com/question/14286410

#SPJ11

The conditions for a ticking time bomb scenario may vary, but typically involve a time-sensitive situation where there is a risk of imminent danger or harm if certain actions are not taken within a specific timeframe.

This could involve factors such as the presence of explosives or other hazardous materials, a specific location or target, a perpetrator with a clear motive or intention, and limited resources or options for resolving the situation. Ultimately, the key factor in a ticking time bomb scenario is the urgency and pressure to act quickly and decisively in order to prevent a catastrophic outcome.

The conditions for a ticking time bomb scenario include a high-pressure situation with a limited time frame, impending danger or threat, and crucial decisions that must be made to prevent potential catastrophic consequences.

To know more about scenario click here

brainly.com/question/17129508

#SPJ11

A hydraulic ram is used to elevate a quantity of water to a higher elevation. Rams are powered by: c. Water

A hydraulic ram uses the force of water to lift a quantity of water to a higher elevation. The hydraulic ram works by utilizing the pressure of a large quantity of water to pump a smaller quantity of water to a higher elevation. This process is repeated, with the water being lifted higher and higher with each cycle. Ultimately, the hydraulic ram is able to lift water to a much higher elevation than it would be able to do on its own. In principle, a hydraulic ram works by an external fluid being pumped into either side of a cylinder simultaneously, this creates a high-pressure and low-pressure side within the cylinder depending on the load that it is trying to move.

Learn more about pressure here: https://brainly.com/question/29341536

#SPJ11

To find the density of the metal, we need to use the formula: density = mass/volume.

First, we need to find the volume of the metal. We can do this by using the displacement method. The water level in the graduated cylinder went up from 25.0 mL to 42.5 mL when the metal was added, so the volume of the metal is:

volume of metal = final volume – initial volume
volume of metal = 42.5 mL – 25.0 mL
volume of metal = 17.5 mL
Next, we need to convert the volume to cubic centimeters (cm3) because density is usually expressed in g/cm3. We know that 1 mL = 1 cm3, so:

volume of metal = 17.5 cm3
Now we can use the formula to find the density:

density = mass/volume
density = 114 g/17.5 cm3
density = 6.51 g/cm3

Therefore, the density of the metal is 6.51 g/cm3. Answer choice (D) is correct.
To find the density of the metal alloy, we need to first determine its volume. Since the metal was placed into a graduated cylinder with water, we can calculate the volume by subtracting the initial water volume from the final water volume:
Volume = Final volume - Initial volume = 42.5 mL - 25.0 mL = 17.5 mL
Now, we can use the formula for density, which is mass divided by volume:
Density = Mass / Volume = 114 g / 17.5 mL = 6.51 g/cm³

So the density of the metal is 6.51 g/cm³ (Option D).

To know more about Density click here .

brainly.com/question/29775886

#SPJ11

If the bear is sliding down the tree at a constant velocity, that means that the net force acting on the bear is zero.

The force of gravity is pulling the bear downwards, while the friction force between the tree and the bear is acting upwards, opposing the force of gravity. We can use Newton's second law of motion, which states that the net force on an object is equal to the product of its mass and acceleration. In this case, the acceleration of the bear is zero, so the net force on the bear must also be zero. Therefore, the magnitude of the friction force must be equal to the magnitude of the force of gravity, which can be calculated as:
force of gravity = mass x acceleration due to gravity
force of gravity = [tex]200 kg * 9.81 m/s^2[/tex]
force of gravity = 1962.0 N
So, the friction force between the tree and the bear is also 1962.0 N, and it acts upwards to balance the force of gravity.

To learn more about velocity click here https://brainly.com/question/17127206

#SPJ11

The correct answer is b. temporary threshold shift. This is a common occurrence after exposure to excessive noise, where the individual experiences a temporary hearing loss that typically lasts a few hours.

If this type of exposure to noise continues, it can eventually lead to permanent hearing loss, known as noise-induced hearing loss. TTS results in a decreased ability to hear soft sounds, as well as a decreased ability to understand speech. It is caused by the destruction of the stereocilia, or tiny hairs, in the inner ear that are responsible for detecting sound. These hairs are not replaced and become permanently damaged if exposed to excessive noise for too long. TTS can be prevented by avoiding loud noises, wearing ear protection, and limiting the duration of exposure to loud sounds.

To learn more about noise click here https://brainly.com/question/29825013

#SPJ11

w=f×d

w=50N×10m

w=500J

reason: because work is calculated in joules and the formula which gives the product of work is force multiplied by its distance (metres)

When J.J. Thomson discovered the electron, the physical property he measured was B) its charge-to-mass ratio, e/m.

He did this by conducting experiments using a cathode ray tube, which allowed him to observe the behavior of electrons in the presence of electric and magnetic fields. By analyzing the deflection of the electron beam, Thomson was able to determine the charge-to-mass ratio of the electron.This ratio was determined through experiments involving the discharge of electricity through a vacuum tube, the deflection of cathode rays by electric and magnetic fields, and the measurement of the radius of the cathode rays. From these experiments, Thomson was able to calculate the charge-to-mass ratio of the electron.

learn more about electrons Refer: https://brainly.com/question/28977387

#SPJ11

The flushometer valve is typically protected by a backflow preventer.

This device ensures that water flows in only one direction, preventing any contamination or backflow of non-potable water into the potable water supply. The backflow preventer can be a reduced pressure zone backflow preventer, which is designed to offer the highest level of protection by creating a zone of reduced pressure between the potable water supply and non-potable water.

To know more about backflow preventer click here:

https://brainly.com/question/30820582

#SPJ11

Binocular disparity refers to the discrepancy between the images viewed by each eye. For items that are closer, the difference is greater, and for those that are farther away, the difference is smaller.

The discrepancy between how an object appears to the left and right eye is known as binocular disparity. The difference is brought about by the horizontal distance between the eyes, which offers each eye a marginally different perspective of the outside world. The brain generates a 3D perception of the surroundings using the discrepancies between the images from the two eyes. The object appears to be closer the higher the binocular dispersion. The images perceived by each eye differ more from one another because the eyes must condense more in order to focus on close objects. On the other hand, since the eyes are almost parallel, objects in the distance have less discrepancy.

learn more about discrepancy here:

https://brainly.com/question/29723856

#SPJ11

The angular speed of the second hand of a watch is 0.10 rad/s.

To find the angular speed of the second hand of a watch in rad/s, we first need to know the time it takes for the second hand to make a complete revolution (360 degrees) around the watch face. Since there are 60 seconds in a minute, the second-hand makes one full revolution in 60 seconds.
Now, we convert 360 degrees to radians. Recall that 1 radian = 180/π degrees:
360 degrees * (π/180) = 2π radians
Next, we calculate the angular speed (ω) using the formula:
ω = θ/t
where θ is the angle in radians and t is the time in seconds.
ω = (2π radians) / (60 seconds) = π/30 radians/second
Thus, the angular speed of the second hand of a watch is:ω = π/30 ≈ 0.1047 rad/s
This value is closest to option B (0.10 rad/s). So, the correct answer is:
Your answer: B) 0.10 rad/s

To learn more about angular speed, refer:-

https://brainly.com/question/14663644

#SPJ11

When six current-carrying conductors are run in the same conduit or cable, the ampacity of each conductor should be adjusted by a factor of 80 percent.

This is based on the National Electrical Code (NEC) 310.15(B)(3)(a) which states that if more than three current-carrying conductors are bundled together in a raceway or cable, the ampacity of each conductor shall be adjusted by a certain percentage. For six current-carrying conductors, the adjustment factor is 80 percent. Conductors to be derated whenever more than three current-carrying conductors are installed together in a raceway, cable, or in a covered ditch in the earth.

Learn more about ampacity here: https://brainly.com/question/31561873

#SPJ11

The True. TXVs used in air conditioning units and heat pumps are interchangeable as long as they are the same size and for the same refrigerant. However, it is recommended to follow the manufacturer's specifications and guidelines to ensure proper operation and efficiency.

True, TXVs Thermostatic Expansion Valves used in air conditioning units and heat pumps are interchangeable as long as they are the same size and for the same refrigerant. Heat pumps and air conditioners have the same set of mechanical components, the same set of the system used for heating purposes can be used for cooling purposes. This is done by the use of a reversible valve in the cycle. flow controllers are designed to adjust the flow of refrigerant into the evaporator so that only vapor leaves the evaporator.

learn more about air here.

https://brainly.com/question/1081420

#SPJ11

The maximum instantaneous power dissipated by the 3.6-hp pump connected to a 240-vrms AC power source is 2704.8 watts.

To find the maximum instantaneous power dissipated by a 3.6-hp pump connected to a 240-vrms AC power source, we can use the formula:

P = Vrms^2 / R

where P is power, Vrms is the root-mean-square voltage, and R is the resistance.

First, we need to convert 3.6 hp to watts:

1 hp = 746 watts
3.6 hp = 3.6 x 746 = 2685.6 watts

Next, we can calculate the resistance of the pump using the formula:

P = Vrms^2 / R
R = Vrms^2 / P

Since the power source is AC, the resistance will be impedance, which is given by:

Z = Vrms / I

where Z is impedance and I is current.

Assuming the pump has a power factor of 1 (which means the voltage and current are in phase), we can use the formula:

Z = Vrms / I = R

to calculate the resistance.

So, the maximum instantaneous power dissipated by the pump can be calculated as follows:

R = Vrms^2 / P = (240)^2 / 2685.6 = 21.3 ohms
Z = R = 21.3 ohms
I = Vrms / Z = 240 / 21.3 = 11.27 A (amperes)

P = Vrms x I = 240 x 11.27 = 2704.8 watts

Therefore, the maximum instantaneous power dissipated by the 3.6-hp pump connected to a 240-vrms AC power source is 2704.8 watts.

Visit here to learn more about  resistance : https://brainly.com/question/30799966
#SPJ11

The Sun is approximately D) 27,000 light-years away from the center of the galaxy.

The Sun is located in the Milky Way galaxy, which is a barred spiral galaxy. The distance from the Sun to the center of the galaxy has been estimated by astronomers using various methods, including measurements of the positions and motions of stars, gas, and dust in the galaxy.

The most recent estimates suggest that the distance from the Sun to the center of the galaxy is approximately 27,000 light-years. This estimate is based on observations of the motion of stars in the galactic disk, as well as the distribution of interstellar gas and dust in the galaxy.

It's worth noting that the distance to the center of the galaxy is not a fixed value, as the galaxy itself is rotating and the Sun is in orbit around the center. The actual distance to the center of the galaxy from the Sun will therefore vary over time.

In summary, the answer is D) 27,000 light-years.

To learn more about center of the galaxy, refer:-

https://brainly.com/question/29854597

#SPJ11

The rate of filtration for a diatomite filter, which is used for filtering liquids in industrial processes, is typically in the range of 15 to 20 gallons per minute per square foot (gpm/ft2).

This rate may vary depending on the specific application and the characteristics of the liquid being filtered. Diatomite filters are known for their high filtration efficiency and ability to capture fine particles, and the recommended filtration rate is typically higher compared to other types of filters. It's important to follow manufacturer's recommendations and industry standards for the appropriate filtration rate to achieve optimal performance and efficiency of the diatomite filter.

Learn more about Diatomite filters here:

https://brainly.com/question/28443963

#SPJ11

The water takes approximately 1.98 hours to fall a distance of 0.250d from its highest level.

In simple harmonic motion, the displacement from the mean position can be expressed as x(t) = A * cos(ωt + φ), where A is the amplitude, ω is the angular frequency, t is time, and φ is the phase angle.

For the given problem, A = d/2 and the period T = 11.9 hours.

Angular frequency ω = 2π/T. When x(t) = 0.250d, we can solve the equation for t.

After substituting the given values and solving for t, we find that it takes approximately 1.98 hours for the water to fall 0.250d from its highest level.

For more such questions on distance, click on:

https://brainly.com/question/26550516

#SPJ11

The weightlifter has done 900 Joules of work to move the weight over her head. Work is a measure of the energy transferred when a force is applied over a distance. In this case, the weightlifter has transferred 900 Joules of energy to the weight.

The work done by the weightlifter to move the weight over her head can be calculated by multiplying the force applied to the weight by the distance it is moved. In this case, the force applied is 500N and the distance moved is 1.8m.

So, the work done is:

Work = Force x Distance

Work = 500N x 1.8m

Work = 900 Joules

It's important to note that the weightlifter's own weight and the force of gravity also played a role in the overall work done to move the weight. The weightlifter had to overcome the force of gravity to lift the weight off the ground, and her own weight contributed to the force required to lift the weight. However, for the purpose of this calculation, we have assumed that the weight was lifted in a smooth and controlled motion without any effort or sudden movements.

To learn more about weightlifter

https://brainly.com/question/30853841

#SPJ4

The concrete will seem much warmer because of how it holds and radiates heat when the female has one foot in the grass and one foot on it. The reason for this is difference in specific heat.

The concrete will seem much warmer because of how it holds and radiates heat when the female has one foot in the grass and one foot on it. Concrete absorbs heat more rapidly and easily than grass because it is porous and a good conductor of heat. Grass will stay cooler because it has a higher insulation value, which traps heat and prevents it from transferring as quickly. The dense, paved surfaces like concrete and asphalt absorb more heat from the sun than natural surfaces like grass or dirt, leading to the phenomenon known as the urban heat island effect. As a result, on a hot summer day, the concrete will seem much warmer than the grass.

Also known as specific heat, this is the quantity of energy required to increase a substance's temperature by one degree Celsius in one gram. The units of specific heat are typically calories or joules per gram per degree Celsius. As an illustration, the specific heat of water is 1 calorie (4.186 joules) per gram per degree Celsius. Joseph Black, a Scottish scientist, discovered that equivalent masses of various substances required different amounts of heat to elevate them over the same temperature range, which led him to establish the concept of specific heat.

To know more about Specific Heat, visit:

https://brainly.com/question/11297584

#SPJ1

Nonmetallic extensions shall be secured in place by approved means at intervals not exceeding 54 inches.

The National Electrical Code (NEC) sets out guidelines and safety standards for electrical installations in the United States. Section 382-30(A) of the NEC specifies that nonmetallic extensions, which are used to extend electrical conduit or raceways, must be secured in place by approved means at intervals not exceeding 4.5 feet, that is 54 inches.

This means that the extensions must be firmly and securely attached to the wall or ceiling at regular intervals to prevent them from sagging or pulling away from the conduit or raceway. Failure to follow this code requirement can result in unsafe electrical installations that may pose a hazard to people and property.

To know more on National Electrical Code

https://brainly.com/question/17215290

#SPJ4

The changes in light intensity are faster for a point source than for a source of plane waves. This is because the inverse square law results in a faster decrease in intensity with distance than the linear decrease seen in plane waves.

The change in light intensity with distance from a point source and a source of plane waves (parallel rays) follows different patterns.

For a point source, the intensity of light decreases with the square of the distance from the source, following what's known as the inverse square law. This means that if you double the distance from the source, the intensity of light decreases to one-fourth of its original value.

For a source of plane waves, the intensity of light decreases linearly with distance. This means that if you double the distance from the source, the intensity of light decreases to half of its original value.

to know more about light intensity refer here:

https://brainly.com/question/9195922#

#SPJ11

The change in light intensity with distance from a point source is much faster compared to the change for a source of plane waves (parallel rays). This is because a point source emits light in all directions, whereas plane waves emit light in a specific direction.

When light is emitted from a point source, it spreads out uniformly in all directions, and the intensity of the light decreases rapidly as the distance from the source increases. This is because the surface area of a sphere (4πr^2) increases as the distance from the source increases, causing the same amount of light to be spread over a larger area. As a result, the light intensity decreases with the square of the distance from the source (I ∝ 1/r^2).

On the other hand, a source of plane waves emits light in parallel rays, which means that the light intensity remains constant as the distance from the source increases. This is because the light is traveling in straight lines and is not spreading out or diverging in any way. Therefore, the light intensity does not decrease with distance.

In conclusion, the change in light intensity with distance from a point source is much faster than the change for a source of plane waves. The light intensity from a point source decreases rapidly as the distance from the source increases, while the light intensity from a source of plane waves remains constant.

Learn more about light intensity here:

https://brainly.com/question/9195922

#SPJ11

A. The percentage of energy of light bulb given out as light is  5%

B. The percentage of energy wasted by the mixer is 60%

C. Part of the mixer becomes hot because some energy is convert to heat energy

We can obtain the percentage of energy given out as light as follow:

Total energy = Wasted energy + Useful energy

100 = 95 + Percentage of energy given out as light

Collect like terms

Percentage of energy given out as light = 100 - 95

Percentage of energy given out as light = 5%

The percentage of energy wasted by the mixer can be obtain as follow:

Total energy = Wasted energy + Useful energy

100 = Wasted energy + 40

Collect like terms

Wasted energy = 100 - 40

Wasted energy by mixer = 60%

A mixer is an equipment which converts electrical energy into mechanical energy.

However, as the mixer is working, certain amount of the energy are converted into heat energy because of the moving parts. This accounts for the hotness of some p[art of the mixer.

Learn more about useful and wasted energy:

https://brainly.com/question/22047965

#SPJ1

Geosynchronous satellites orbit at about four earth radii, where the earth's gravitational pull is strong enough to keep the satellite in a stable orbit.

This orbit is known as the geostationary orbit and is at an altitude of approximately 36,000 kilometers above the Earth's surface. At this altitude, the gravitational pull is still significant enough to keep the satellite in orbit, but not so strong that it will cause the satellite to spiral into the Earth.

The earth’s gravitational pull is given by the formula g = GM/r 2, where G is the universal gravitational constant, M is the mass of the earth, and r is the distance from the center of the earth. The value of g on the surface of the earth is about 9.8 m/s 2.

If we assume that the earth’s radius is about 6.4 × 10 6 m, then four earth radii would be about 2.56 × 10 7 m. Plugging this value into the formula, we get:

g = (6.67 × 10 -11 Nm 2 /kg 2) × (5.97 × 10 24 kg) / (2.56 × 10 7 m) 2

g = 0.61 m/s 2

Find out more about Geosynchronous satellites

brainly.com/question/29102626

#SPJ11

The above statement is  True.A serial distribution system involves the transfer of data or signals from one device to another in a sequential manner.

In this system, each device in the network is connected to the next one, forming a chain. However, this method has some disadvantages compared to the use of distribution boxes.

Distribution boxes, on the other hand, allow for a more efficient distribution of power or signal to multiple devices simultaneously. They also provide a central point for managing and monitoring the distribution process.

Therefore, it can be concluded that the use of a serial distribution system has some disadvantages over the use of distribution boxes. A serial distribution system has disadvantages compared to the use of distribution boxes. In a serial distribution system, devices are connected in a sequence, causing potential signal degradation and making it more difficult to troubleshoot issues. Distribution boxes, on the other hand, allow for parallel connections, which can improve signal quality and make it easier to identify and fix problems.

Learn more about the power here:- brainly.com/question/29575208

#SPJ11

The direction of the frictional force on the tires of a front-wheel-drive car as the speed increases on a horizontal road is opposite to the direction of the car's motion.

This is because the tires need to grip the road surface to provide the necessary traction to move the car forward, and the frictional force acts in the opposite direction to the movement of the car.

The amount of frictional force depends on several factors such as the weight of the car, the quality of the tires, the road conditions, and the speed of the car. In a front-wheel drive car, when the speed is increasing on a horizontal road, the direction of the frictional force on the front tires is forward, as they provide the necessary traction for acceleration.

On the rear tires, the frictional force acts in the opposite direction, or backward, as they resist the forward motion while supporting the weight of the car.

To learn more about frictional force click here

brainly.com/question/30280752

#SPJ11