Delta V R rms equals I rms times R. true or false

Failure to adequately seal well casings is one of the most frequent causes of contamination of wells bored through rock, clay, or hardpan.

Well casings are used to seal off the surrounding soil and rock, protecting wells from contamination. Contaminants can enter into the gaps and cracks.

This is a typical issue in wells that are dug through rock, clay, or hardpan, where the soil is less permeable and less effective in filtering out impurities. It is crucial to properly seal well casings since tainted well water can be dangerous to both humans and animals' health. Well casings can be kept clean and tested regularly to help against contamination.

To know more about Contamination, visit,

https://brainly.com/question/28237583

#SPJ4

Given statment "thermal motion approaches a minimum as the temperature approaches absolute zero." is true. Because as the temperature approaches absolute zero, thermal motion decreases and approaches a minimum, which is in line with the third law of thermodynamics.

True. Thermal motion is the random movement of particles in a substance. At higher temperatures, these particles have more kinetic energy and therefore move around more rapidly.

As the temperature approaches absolute zero (0 Kelvin or -273.15 degrees Celsius), the particles lose kinetic energy and move around less. In fact, at absolute zero, particles would theoretically come to a complete stop, and there would be no thermal motion.
This phenomenon is known as the third law of thermodynamics, which states that the entropy (or disorder) of a perfect crystal at absolute zero is zero. This means that there is no thermal motion or randomness in a perfect crystal at absolute zero. However, it is impossible to reach absolute zero in practice since some residual thermal motion always exists due to quantum effects.
For similar questions on thermal motion

https://brainly.com/question/24658017

#SPJ11

The exact location and identity of every subatomic particle in the universe at this exact moment is unknown and cannot be determined.

The position and velocity of subatomic particles cannot be precisely determined simultaneously according to the Heisenberg uncertainty principle, which means that it is impossible to know the exact location and momentum of a particle at the same time.

Additionally, subatomic particles are constantly interacting with each other, making it impossible to track their exact locations and identities at any given moment.

Scientists can make probabilistic predictions about the locations of subatomic particles through experiments and mathematical models, but these predictions are never certain.

The behavior of subatomic particles is governed by probability distributions, which describe the likelihood of finding a particle in a particular location or state.

to know more about subatomic particle refer here:

https://brainly.com/question/29765133#

#SPJ11

It is impossible to determine the exact location and identity of every subatomic particle in the universe at this exact moment. This is due to the uncertainty principle in quantum mechanics, which states that the more precisely the position of a particle is known, the less precisely its momentum can be known.

According to the Heisenberg uncertainty principle, it is impossible to simultaneously measure the position and momentum of a particle with absolute precision. This means that the exact location and momentum of a subatomic particle cannot be known with certainty at any given moment, and there will always be a degree of uncertainty associated with any measurement.

Additionally, the vast size and complexity of the universe make it practically impossible to observe every subatomic particle. Therefore, scientists rely on statistical probabilities and models to understand the behavior of particles at the subatomic level.

Therefore, the exact location and identity of every subatomic particle in the universe at this exact moment cannot be determined with certainty, and our understanding of the subatomic world is based on statistical and probabilistic descriptions rather than absolute knowledge.

Learn more about Heisenberg uncertainty principle here:

https://brainly.com/question/30402752

#SPJ11

According to the question the new resonant frequency will be larger than it was before.

Frequency is a measure of how often a given event or phenomenon occurs, typically measured as the number of times it occurs in a given period of time. It is usually expressed as the number of occurrences per unit of time, such as per second, minute, day, week, or year. Frequency is an important concept in many areas of physics, mathematics, and engineering.

The resonant frequency of a stretched string is determined by its length and tension. When the distance between the two bridges is increased, the length of the string is increased and the resonant frequency will also increase. Therefore, the new resonant frequency will be larger than it was before.

Therefore, the correct option is C
To learn more about frequency
https://brainly.com/question/254161
#SPJ4

The negative sign indicates that the image is inverted. The height of the image is 1.0 cm .

To find the height of the image of the flower, we can use the formula:

1/f = 1/do + 1/di

Where f is the focal length, do is the object distance (distance from the mirror to the object), and di is the image distance (distance from the mirror to the image).

First, we need to find the image distance. We know that the object distance is 100 cm and the focal length is 25 cm. Plugging these values into the formula, we get:

1/25 = 1/100 + 1/di

Simplifying, we get:

1/di = 1/25 - 1/100
1/di = 0.04
di = 25 cm

Now that we know the image distance, we can use the formula for magnification to find the height of the image.

The formula for magnification is:

m = -di/do

Where m is the magnification.

Plugging in the values we have, we get:

m = -25/100
m = -0.25

The negative sign indicates that the image is inverted.

The magnification tells us that the image is 0.25 times the size of the object.

Finally, we can use the height of the object and the magnification to find the height of the image:

height of image = magnification x height of object

height of image = -0.25 x 4.0 cm

height of image = -1.0 cm

The negative sign indicates that the image is inverted. The height of the image is 1.0 cm, meaning it is smaller than the original object.

To know more about convex spherical mirror :

https://brainly.com/question/13725031

#SPJ11

The grinding of garbage is an acceptable method of garbage disposal.

Garbage disposal units, also known as garbage disposals or waste disposal units, are appliances installed under a kitchen sink that grind food waste into small particles that can be safely disposed of through the home's plumbing system.

This method of garbage disposal is a convenient way to dispose of food waste and can help to reduce the volume of garbage sent to landfills.

While there are some concerns about the environmental impact of garbage disposals, they are generally considered to be a safe and acceptable method of garbage disposal when used properly.

To know more about garbage disposal: brainly.com/question/31033179

#SPJ11

As the temperature of air is reduced to its dew point, the phase change that is most likely to occur is the condensation of water vapor into liquid droplets, also known as dew.

As the temperature of air is reduced to its dew point, the phase change that is most likely to occur is condensation. Condensation is the process by which a gas changes into a liquid as it loses heat and its temperature decreases. When air is cooled to its dew point, which is the temperature at which the air becomes saturated with moisture and cannot hold any more water vapor, the excess moisture in the form of water vapor condenses into liquid droplets or frost, depending on the temperature and other conditions. This is commonly observed as dew forming on surfaces such as grass, leaves, and windows, or frost forming on colder surfaces during cold weather conditions.

To know more about dew point,

https://brainly.com/question/15313810

#SPJ11

True. The normal force is the force that opposes the force of gravity on an object that is in contact with a surface.

When an object is placed on a surface, the surface pushes back on the object with a force that is perpendicular to the surface. This force is called the normal force. The normal force is equal in magnitude to the force of gravity on the object, but acts in the opposite direction, which allows the object to remain in a state of static equilibrium. For example, when you stand on the ground, the normal force exerted by the ground on your feet is equal in magnitude to your weight, but acts in the opposite direction, which prevents you from sinking into the ground.

Learn more about gravity here:

https://brainly.com/question/31321801

#SPJ11

Answer:

0.5 or 50%.

Explanation:

The ripple ratio is a measure of the magnitude of AC voltage compared to the DC voltage in a circuit, typically used in power electronics. It is calculated as the ratio of the amplitude of the AC component (VAC) to the DC component (VDC) in a waveform.

Given:

Amplitude of AC component (VAC) = 10 Vpp (peak-to-peak) = 10/2 = 5 V

Nominal DC voltage (VDC) = 10 V

Ripple Ratio = VAC / VDC

Ripple Ratio = 5 V / 10 V

Ripple Ratio = 0.5 (or 50% when expressed as a percentage)

So, the ripple ratio for the given circuit is 0.5 or 50%.

Submarine and the torpedo were initially at rest, torpedo left submarine with a speed of 89.2 m/s,  a) recoil speed of the submarine is 0.892 m/s in the opposite direction of the torpedo. b) recoil of the submarine  is in the opposite direction of the velocity vector of the torpedo.

To solve this problem, we can use the principle of conservation of momentum. The momentum of the system (submarine + torpedo) before the torpedo is fired is zero, since both objects are at rest. After the torpedo is fired, the total momentum of the system is still zero, but now the torpedo has momentum in one direction, so the submarine must have an equal and opposite momentum in the other direction.

a) Using the equation for conservation of momentum, we can write:

0 = m_sub * v_sub + m_tor * v_tor

where m_sub is the mass of the submarine, v_sub is the recoil speed of the submarine, m_tor is the mass of the torpedo, and v_tor is the speed of the torpedo. Plugging in the values given in the problem, we get:

0 = m_sub * v_sub + m_tor * 89.2 m/s

Solving for v_sub, we get:

v_sub = - m_tor * 89.2 m/s / m_sub

Plugging in the values for m_tor and m_sub (which are not given in the problem, so we'll have to make some assumptions), we get:

v_sub = - 1000 kg * 89.2 m/s / 100000 kg

v_sub = -0.892 m/s

Therefore, the recoil speed of the submarine is 0.892 m/s in the opposite direction of the torpedo.

b) The direction of recoil of the submarine is opposite to the direction of the torpedo, so it is in the opposite direction of the velocity vector of the torpedo.

To learn more about velocity vector click here

brainly.com/question/13492374

#SPJ11

The speed of the cylinder at the bottom of the inclined plane is approximately 1.44 m/s.

To determine the speed of the cylinder at the bottom of the incline, we can use the conservation of energy principle, which states that the total mechanical energy of the system is conserved.

At the top of the incline, the cylinder has only potential energy, which is given by:

PE = mgh

where m is the mass of the cylinder, g is the acceleration due to gravity, and h is the height of the incline.

At the bottom of the incline, the cylinder has both kinetic energy due to its translational motion and rotational energy due to its spinning motion. The total kinetic energy is given by:

KE = (1/2)mv^2 + (1/2)Iw^2

where v is the linear speed of the cylinder, I is its moment of inertia, and w is its angular speed.

Since the cylinder rolls without slipping, we can relate v and w using the equation:

v = rw

where r is the radius of the cylinder.

The moment of inertia of a solid cylinder is given by:

I = (1/2)mr^2

Substituting these expressions for KE and I into the conservation of energy equation, we obtain:

mgh = (1/2)mv^2 + (1/2)(1/2)mr^2w^2

Simplifying and substituting v = rw, we get:

v = √(2gh/3)

Plugging in the given values, we get:

v = √(2 × 9.81 m/s^2 × 0.55 m/3)

≈ 1.44 m/s

Therefore, the speed of the cylinder at the bottom of the inclined plane is approximately 1.44 m/s.

To know more about conservation of energy principle :

https://brainly.com/question/28856450

#SPJ11

To calculate the speed of the disk in conceptual example 10-17 at the bottom of the inclined plane, we need to use the conservation of energy principle. The potential energy at the top of the incline is converted into kinetic energy at the bottom.

First, we need to calculate the potential energy at the top of the incline. The potential energy can be calculated using the formula:

PE = mgh

Where m is the mass of the disk, g is the acceleration due to gravity (9.81 m/s^2), and h is the height of the incline (0.55 m).

PE = (0.5 kg) x (9.81 m/s^2) x (0.55 m) = 2.7 J

This potential energy is converted into kinetic energy at the bottom of the incline, which can be calculated using the formula:

KE = 0.5mv^2

Where v is the speed of the disk at the bottom.

Since energy is conserved, we can set PE equal to KE:

PE = KE

2.7 J = 0.5(0.5 kg)v^2

Solving for v, we get:

v = sqrt(2.7 J / 0.25 kg)

v = 3.3 m/s

Therefore, the speed of the disk in conceptual example 10-17 at the bottom of the inclined plane is 3.3 m/s.
In the conceptual example 10-17, a disk rolls down an inclined plane. To calculate the speed of the disk at the bottom of the inclined plane with a height of 0.55 meters, we can use the conservation of mechanical energy principle. This principle states that the total mechanical energy (potential energy + kinetic energy) of the disk remains constant if no external forces are acting on it.

At the top of the incline, the disk has only potential energy (PE) due to its height, and no kinetic energy (KE) since it is not moving. As it rolls down, the potential energy is converted into kinetic energy (both translational and rotational).

The potential energy at the top is given by PE = m * g * h, where m is the mass of the disk, g is the acceleration due to gravity (approximately 9.81 m/s^2), and h is the height of the incline (0.55 m).

At the bottom of the incline, the disk has no potential energy, and its kinetic energy is a combination of translational (KE_t) and rotational (KE_r) components. The total kinetic energy is given by KE = (1/2) * m * v^2 + (1/2) * I * ω^2, where v is the linear velocity, I is the moment of inertia of the disk, and ω is the angular velocity.

Since the total mechanical energy is conserved, we can set the potential energy at the top equal to the kinetic energy at the bottom:

m * g * h = (1/2) * m * v^2 + (1/2) * I * ω^2

To solve for the linear velocity (v) at the bottom of the incline, we also need to know the mass of the disk, the moment of inertia, and the angular velocity. These values are not provided in your question. However, once you have this information, you can use the conservation of mechanical energy equation to find the speed of the disk at the bottom of the inclined plane.

Learn more about  disk in conceptual here;

https://brainly.com/question/31544769

#SPJ11

The total mechanical energy of the apple is of a 0.100-kilogram apple hangs in a tree 1.50 meters above the ground. Ignoring frictional effects, the total mechanical energy of the apple is 1.47 J (joules)

To find the total mechanical energy, we need to consider both the potential energy and kinetic energy of the apple. Since the apple is not moving, its kinetic energy is zero. However, it does have gravitational potential energy due to its height above the ground. The formula for gravitational potential energy is:
PE = mgh
where m is the mass of the object (0.100 kg), g is the acceleration due to gravity [tex](9.81 m/s^{2})[/tex], and h is the height above the ground (1.50 m).
Plugging in these values, we get:
[tex]PE = (0.100 kg)(9.81 m/s^{2})(1.50 m)[/tex]

= 1.47 J
Therefore, the total mechanical energy of the apple is 1.47 J.
In summary, the total mechanical energy of the apple hanging in the tree is 1.47 J, which is solely due to its gravitational potential energy.

For more information on potential energy kindly visit to

https://brainly.com/question/3067704

#SPJ11

The magnitude of the force on the electron in the electric field is 1.6 * [tex]10^{-12}[/tex]N, directed in the opposite direction of the electric field intensity.

What is Electric Field?

Electric field is a physical quantity that describes the influence or effect that an electric charge exerts on other charges or objects in its vicinity. It is a vector quantity, meaning it has both magnitude and direction. The electric field is created by a charged object and extends radially outward or inward depending on the type of charge (positive or negative) and decreases with distance according to the inverse square law.

Electric field intensity (E) between the plates of a parallel plate capacitor is given by the formula:

E = V/d

Substituting the given values:

E = 5 * [tex]10^{4}[/tex] V / 5 * [tex]10^{-3}[/tex] m

E = 1 * [tex]10^{7}[/tex]V/m

So, the magnitude of the electric field intensity between the plates of the parallel plate capacitor is 1 * [tex]10^{7}[/tex] V/m.

The force (F) on an electron in an electric field is given by the formula:

F = q * E

Substituting the given values:

F = -1.6 * [tex]10^{-19[/tex] C * 1 *[tex]10^{7}[/tex] V/m

F = -1.6 *[tex]10^{-12}[/tex] N

Learn more about Electric Field from the given link

https://brainly.com/question/19878202

#SPJ1

The  diameter of the U.S. dime when expressed in nanometers is 1.8 x 10^7 nm, which corresponds to option B).

The diameter of an object is the distance across the object passing through its center, measured in units such as millimeters (mm), centimeters (cm), or meters (m). In the case of the U.S. dime, the diameter was changed to approximately 18 mm in 1828.

To convert this diameter to nanometers (nm), we need to use the conversion factor that relates millimeters to nanometers. One millimeter is equal to one million nanometers (1 mm = 1,000,000 nm).

So, to convert 18 mm to nanometers, we can multiply 18 by 1,000,000 as follows:

18 mm * 1,000,000 nm/mm = 18,000,000 nm

Therefore, the diameter of the U.S. dime when expressed in nanometers is 1.8 x 10^7 nm, which corresponds to option B).

Visit to know more about Diameter:-

brainly.com/question/23220731

#SPJ11

An object is placed at a distance of 27.0 cm away from a thin convex lens with a focal length of 9.00 cm. The image is located at a distance of 6.75 cm from the lens and the image formed is real and inverted.  

To find the distance of the image formed by a convex lens, we can use the lens formula:
1/f = 1/u + 1/v
where f is the focal length of the lens, u is the object distance, and v is the image distance.
Given:
Object distance (u) = -27.0 cm (negative because it's on the same side as the object)
Focal length (f) = 9.00 cm
Plug in the values into the lens formula:
1/9 = 1/(-27) + 1/v
Now, let's solve for v:
1/v = 1/9 + 1/27
1/v = 3/27 + 1/27
1/v = 4/27
v = 27/4
The image distance (v) = 6.75 cm. The positive value of v indicates that the image is formed on the opposite side of the lens compared to the object.
Since the image is formed on the opposite side and has a positive image distance, it is a real and inverted image.

To learn more about the convex lens, refer:-

https://brainly.com/question/1604692

#SPJ11

Using the thin lens formula:

1/f = 1/d0 + 1/di

where f is the focal length of the lens, d0 is the object distance from the lens, and di is the image distance from the lens.

Plugging in the given values:

1/9 = 1/27 + 1/di

Simplifying the equation:

1/di = 1/9 - 1/27 = (3 - 1)/27 = 2/27

di = 27/2 = 13.5 cm

The image is formed 13.5 cm away from the lens.

To determine the type of image formed, we can use the following rules:

If di is positive, the image is real and located on the opposite side of the lens from the object.

If di is negative, the image is virtual and located on the same side of the lens as the object.

If di is infinite, the image is formed at infinity and is said to be a "point image."

If di is zero, the image is formed at the same location as the object and is said to be a "coincident image."

In this case, since di is positive, the image is real and located on the opposite side of the lens from the object.

To know more about lens visit here :

https://brainly.com/question/28042333

#SPJ11

Dust that is heated to 30 K will emit a blackbody spectrum that peaks at d. 100μm . It is given by Wein's Displacement Law.

According to Wien's Law, which bears the name of German physicist Wilhelm Wien, objects with varying temperatures emit spectra with varied peak wavelengths. Shorter wavelength radiation is emitted by hotter things, giving them their blue appearance. Similar to this, cooler things release longer wavelength light, giving them a reddish appearance. In 1893, Wilhelm Wien developed the Wien's law, also known as the Wien's displacement law, which asserts that different wavelengths of black body radiation have temperature peaks that are inversely proportional to temperatures. Wien's constant is a physical constant that describes the correlation between the black body's thermodynamic temperature and wavelength.

The wavelength at which a blackbody emits the maximum radiation is given by Wien's Displacement law, which is described by

λmax = [tex]\frac{2898}{T}[/tex],

where λmax is the peak wavelength in micrometers, and T is the temperature in kelvins.

For a dust particle heated to 30 K, this would give a peak wavelength at λmax = 2898/30 ≈ 96.6 µm.

So the correct answer is d. 100 µm.

To know more about Blackbody, visit:

https://brainly.com/question/28644935

#SPJ1

phenomenon is known as electrostatic induction.

When a rubber rod is rubbed with fur, the rubber rod becomes negatively charged due to the transfer of electrons from the fur to the rubber. If the fur is then quickly brought near the bulb of an uncharged electroscope, the negative charge on the fur will induce a positive charge on the leaves of the electroscope by repelling electrons to the bottom of the leaves. Therefore, the sign of the charge on the leaves of the electroscope will be positive. This is because opposite charges attract each other and the positively charged leaves are attracted to the negatively charged fur. This phenomenon is known as electrostatic induction.

To know more about electrostatic induction click here:

https://brainly.com/question/27716037

#SPJ11

The Given a heater with a fixed heat flux, we have two materials of equal thickness, with Material A having a thermal conductivity of kea, and Material B having a thermal conductivity of k _b. We know that k _a < k _b, and heat transfer through the wall is one-dimensional conduction.

The steady state, the temperature difference across the two sides of each wall can be determined using Fourier's Law of Heat Conduction = -k * dT/dx Where q is the heat flux, k is the thermal conductivity, dT is the temperature difference, and dx is the thickness of the material. Since the heat flux (q) is fixed and the thickness dx of both materials is equal, we can rearrange the equation to solve for the temperature difference dT across the two sides of each wall dT = -q * dx / k For Material A, the temperature difference dT _a will bed T _a = -(q * dx) / k _a For Material B, the temperature difference dT _b will be dT _b = -q * dx / k _b Since k _a < k _b, we can conclude that'd > dT _b So, at steady-state, the temperature difference across the two sides of Material A will be greater than the temperature difference across the two sides of Material B.

learn more about flux here.

https://brainly.com/question/15237486

#SPJ11

The magnitude of the impedance in Ω of a 0.50 μF capacitor at a frequency of 10.0 kHz can be calculated using the formula Z = 1/(2πfC), where Z is the impedance, f is the frequency in Hz, and C is the capacitance in Farads.

Plugging in the given values, we get:

Z = 1/(2π x 10,000 x 0.50 x 10^-6)
Z = 31.83 Ω (rounded to two decimal places)

Therefore, the magnitude of the impedance of a 0.50 μF capacitor at a frequency of 10.0 kHz is approximately 31.83 Ω. Magnitude is a word used to indicate something's magnitude or scope. It may be used to describe a variety of characteristics, including the actual size of an item, the quantity or intensity of a certain attribute or phenomena, or the significance or influence of a specific event or concept. Magnitude may be measured using a variety of scientific tools or procedures depending on the situation and is frequently stated quantitatively, for example, in terms of length, mass, volume, or strength. A sense of size, significance, or importance is often implied by the phrase magnitude, which is frequently used in disciplines including physics, astronomy, geology, and mathematics.

Learn more about magnitude  here:

https://brainly.com/question/29766788

#SPJ11

One example of a chemical that is frequently applied just prior to filtration is a coagulant.

Coagulants or flocculants are chemicals that are commonly used in water and wastewater treatment processes to aid in the removal of suspended particles, colloids, and other impurities from water or wastewater. These chemicals are typically added just prior to the filtration step in the treatment process.

Coagulants are substances that cause destabilization and aggregation of suspended particles and colloids in water, leading to the formation of larger particles called flocs. These flocs can be easily removed by sedimentation or filtration. Common coagulants used in water treatment include aluminum sulfate (alum), ferric chloride, and polyaluminum chloride (PAC).

Flocculants, on the other hand, are substances that promote the aggregation of smaller flocs into larger, settleable flocs. They help to speed up the sedimentation process and improve the efficiency of solid-liquid separation. Flocculants are typically used in conjunction with coagulants to enhance the overall performance of the water treatment process.

To know more about filtration ,

https://brainly.com/question/31504556

#SPJ11

The Sun, along with the rest of the solar system, takes approximately 230 million years to complete one orbit around the Milky Way Galaxy.

This is a long period of time in comparison to our human lifespan, and it shows the vastness of our universe. The Milky Way Galaxy is estimated to be around 100,000 light-years in diameter, and it contains around 100-400 billion stars. The Sun is located about 25,000 light-years away from the center of the galaxy, and it is part of a spiral arm called the Orion Arm. As the Sun orbits the galaxy, it also moves up and down through the disk due to the gravitational influence of nearby stars and dark matter. This complex motion is known as the galactic tide. The study of galactic astronomy is an exciting field that helps us understand the structure and evolution of our Milky Way Galaxy, as well as other galaxies in the universe.

learn more about galaxy here

https://brainly.com/question/12532606

#SPJ11

The mass of zinc in the coin is 2.444325 g. It is obtained by subtracting the mass of the coin from the mass of the copper.

We have a penny with a mass of 2.507 g and 2.5% of it is copper. Find the mass of zinc.

We should know that a penny contains of copper and zinc. To find the mass of zinc in the penny, we first need to calculate the mass of copper in the penny. Then, we can subtract the mass of copper from the total mass of the penny.

Since the penny is 2.5% copper, we can multiply the total mass of the penny (2.507 g) by 2.5% to get the mass of copper.

The mass of copper is

= 2.507 g × 2.5%

= 2.507 g × 0.025

= 0.062675 g

So, the penny contains 0.062675 g of copper.

The mass of zinc is

= mass of penny - mass of copper

= 2.507 g - 0.062675 g

= 2.444325 g

Hence, the mass of zinc in the penny is 2.444325 g.

Learn more about calculating percentage here:

brainly.com/question/29832925

#SPJ11

This is due to the fact that when kinetic energy is doubled, the speed of the block increases by the square root of 2, resulting in an increase of 40% in the velocity.

Kinetic energy is the energy of motion. It is the energy that an object has because of its motion. Kinetic energy can be found in a variety of forms such as thermal energy, electrical energy, and mechanical energy. Kinetic energy can be converted into other forms of energy such as potential energy. Kinetic energy is also known as the energy of motion and is associated with the movement of objects. When an object is moving, its kinetic energy increases, and when an object is at rest, its kinetic energy is zero.

Doubling the total energy of the block would double its kinetic energy, as the potential energy remains constant. Since the kinetic energy of the block is proportional to its speed squared, the maximum speed of the block would also be doubled, from 20cm/s to 40cm/s.

To learn more about kinetic energy
https://brainly.com/question/8101588
#SPJ4

The badger's displacement from t=2s to t=3s is -5m.

Displacement is the change in position of an object. From t=0s to t=1s, the badger's velocity increases from 0 m/s to 5 m/s, so its displacement during this time interval is:

From t=1s to t=3s, the badger's velocity decreases from 5 m/s to -5 m/s. Its displacement during this time interval is:

From t=3s to t=6s, the badger's velocity remains constant at -5 m/s. Its displacement during this time interval is:

Therefore, the total displacement of the badger from t=0s to t=6s is

To find the displacement from t=2s to t=3s, we need to subtract the displacement from t=0s to t=2s from the displacement from t=0s to t=3s:

So the badger's displacement from t=2s to t=3s is -5 m.

To learn more about displacement, here

https://brainly.com/question/30087445

#SPJ1

The complete question is:

A badger is trying to cross the street. Its velocity v as a function of time t is given in the graph below where rightwards is the positive velocity direction. A set of black coordinate axes are given with the vertical axis labeled "v (m/s)" and the horizontal axes labeled "t (s)". A curve that relates v to t is shown in blue. It begins with a straight line of endpoints (0,0) and (1,5). This first line is connected to a second line with endpoints (1,5) and (3,-5). This second line is then connected to a third line of endpoints (3,-5) and (6,-5). A set of black coordinate axes are given with the vertical axis labeled "v (m/s)" and the horizontal axes labeled "t (s)". A curve that relates v to t is shown in blue. It begins with a straight line of endpoints (0,0) and (1,5). This first line is connected to a second line with endpoints (1,5) and (3,-5). This second line is then connected to a third line of endpoints (3,-5) and (6,-5). What is the badger's displacement \Delta xΔxdelta, x from t=2\,\text st=2st, equals, 2, start text, s, end text to 3\,\text s3s3, start text, s, end text?

Approximately The angular speed are the tires rotating is 214 rev/min.

To find the angular speed, we need to use the formula:
Angular speed (ω) = linear speed (v) / radius (r)
Given the radius (r) is 0.35 meters and the linear speed (v) is 7.8 m/s, we can plug these values into the formula:
ω = 7.8 m/s / 0.35 m
ω = 22.29 radians/s
To convert radians per second to revolutions per minute, we can use the following conversion:
1 revolution = 2π radians
1 minute = 60 seconds
ω = (22.29 radians/s) * (1 revolution / 2π radians) * (60 seconds / 1 minute)
ω ≈ 213.4 rev/min
The closest answer is option C) 214 rev/min.

learn more about angular speed refer: https://brainly.com/question/14663644

#SPJ11

Trenches greater than 4-feet in depth require a reliable form of personnel exit, such as ladders. Hydraulic shores, screw jacks, or solid sheeting to prevent the trench from collapsing and endangering workers. It is important to adhere to these safety measures to prevent accidents and injuries on the job site.

Trenches greater than 4-feet in depth require a reliable form of personnel exit, such as ladders, according to Occupational Safety and Health Administration (OSHA) regulations. This is to ensure the safety of workers who may need to exit the trench quickly in case of an emergency or hazardous situation. Hydraulic shores, screw jacks, and solid sheeting are types of protective systems used in trenches to prevent cave-ins and provide support, but they may not necessarily be required for trenches greater than 4-feet in depth.

Learn more about Hydraulic shores here:

https://brainly.com/question/5125371

#SPJ11

Answer:

Isaac Newton did not invent gravity. Gravity is a fundamental force of nature that has always existed. Newton's contribution was to formulate the laws of motion and universal gravitation, which helped to explain the behavior of objects under the influence of gravity.

As for how people flew before the development of powered flight, they relied on a variety of methods, such as gliding, using hot air balloons, and being lifted by the wind in kites. For example, in China, people have been flying kites for more than 2,000 years. In the late 18th century, the Montgolfier brothers developed hot air balloons, which allowed humans to ascend into the air for short periods of time. And in the late 19th and early 20th centuries, pioneers of aviation such as the Wright brothers and their contemporaries developed powered aircraft, which eventually led to modern air travel.

The mass of the nickel deposited is 5.87 g. The correct option is B.

To determine the mass of nickel deposited during the electroplating process, we can use the formula:

mass = (moles of electrons) × (molar mass of nickel) × (Faraday constant)

First, we need to find the moles of electrons. As 1 mole of electrons is equal to 1 Faraday, in this case, 0.200 Faraday of electrical charge corresponds to 0.200 moles of electrons.

Now, we need to find the molar mass of nickel. The atomic mass of nickel (Ni) is approximately 58.7 g/mol.

For the electroplating of nickel from NiSO₄, the balanced equation is:

Ni²⁺(aq) + 2e⁻ → Ni(s)

From the equation, we can see that 1 mole of nickel ions (Ni²⁺) requires 2 moles of electrons to form 1 mole of nickel metal (Ni).

Next, we will calculate the moles of nickel deposited:

moles of Ni = (moles of electrons) / 2
moles of Ni = 0.200 moles / 2 = 0.100 moles

Now we can calculate the mass of the nickel deposited:

mass = (moles of Ni) × (molar mass of nickel)
mass = (0.100 moles) × (58.7 g/mol) = 5.87 g

to know more about electroplating refer here:

https://brainly.com/question/20112817#

#SPJ11

To determine the mass of nickel deposited in the electroplating process, we need to use the equation:

mass of substance = (current x time x atomic mass) / (faraday's constant x valency)

In this case, we know that 0.200 faraday of electrical charge is passed through the solution of NiSO4. We also know that the valency of nickel is 2 (since NiSO4 contains one nickel ion with a +2 charge). The atomic mass of nickel is 58.69 g/mol. Faraday's constant is 96,485 C/mol.

So, plugging in the values we get:

mass of nickel = (0.200 x 1 x 58.69) / (96,485 x 2)
mass of nickel = 0.000608 g

However, the answer options given are in grams, so we need to convert our answer to grams:

mass of nickel = 0.000608 g = 0.608 mg = 0.000000608 g

Therefore, the correct answer is (d) 58.7 g.
In the electroplating of nickel, 0.200 Faraday of electrical charge is passed through a solution of NiSO4. The mass of nickel deposited can be calculated using Faraday's law of electrolysis.

First, we need to find the molar equivalent of 0.200 Faraday of charge. One Faraday is equivalent to the charge of one mole of electrons (approximately 96,485 C/mol). So, 0.200 Faraday is equivalent to 0.200 moles of electrons.

NiSO4 dissociates into Ni²⁺ and SO₄²⁻ ions in the solution. Nickel has a charge of +2, so one mole of nickel ions requires two moles of electrons for reduction (Ni²⁺ + 2e⁻ → Ni).

Since 0.200 moles of electrons are available, the moles of nickel deposited are 0.200 / 2 = 0.100 moles.

Now, to find the mass of nickel deposited, multiply the moles by the molar mass of nickel (58.69 g/mol):

0.100 moles × 58.69 g/mol = 5.87 g

Thus, the mass of nickel deposited is 5.87 g (option B).

Learn more about electrical charge here;

https://brainly.com/question/9194793

#SPJ11

Mode of transportation is the slowest, most difficult to access, and limited in terms of products it can carry, though it offers the most reliable service (E). rail is the correct option.

In general, rail transportation takes longer than other types of transportation including vehicles, pipelines, watercraft (like ships), and aero planes. Railways often follow set routes and schedules, which, depending on the rail infrastructure present, may restrict their accessibility in some locations. The kinds and quantities of goods that can be transported by rail may also be constrained since railcars have certain size and capacity restrictions.

However, compared to other forms of transportation, rail travel is renowned for its dependability because trains often run on set timetables and are less impacted by bad weather or heavy traffic.

Therefore, the correct option is (E).

To know more about transportation

https://brainly.com/question/29611706

#SPJ4

To make green light from cyan light, you need to add red light to it. Cyan light has a wavelength of around 490-520 nanometers, which means it is close to blue-green on the visible spectrum. When you add red light, which has a wavelength of around 620-750 nanometers, the combination of the two colors will produce green light. This is because red and cyan are complementary colors, meaning they are opposite each other on the color wheel, and when mixed together, they produce green light.

~~~Harsha~~~

Answer:

yellow light

Explanation:

Yellow light can be added to cyan light to make green.