TVA - Tennessee Valley Authority. Power companies fiercely opposed the TVA because they disliked the less expensive energy it offered and thought the agency posed a danger to free market.
A notched bar is broken in a pendulum-style impact tester to determine the ductile/brittle transition temperature for every specific steel sample. The energy absorbed during the fracture is then calculated. Steel 1045 specimens break apart when the temperature drops below zero and display brittle-like fracture (specimens 1 to 4 from -200oC to 0.0oC), however when the temperature rises, the specimens display ductile-like fracture (specimens 5 to 7 from 24oC to 100oC). Mild steel is malleable and ductile because it contains between 0.05 and 0.30 percent carbon. This steel has low carbon, with a carbon concentration of about 0.3%, making it neither overly brittle nor overly ductile. It is utilized practically everywhere since it is in the middle, which strikes a good balance. The Tennessee Valley Authority (TVA) is a U.S. electric utility company that is controlled by the federal government. All of Tennessee is included in TVA's service region, along with small portions of Georgia, North Carolina, Virginia, Alabama, and Mississippi. Despite being a governmental agency, TVA is run like a private for-profit business and does not receive any taxpayer money. Its headquarters are in Knoxville, Tennessee, and it is both the largest public utility and the sixth-largest power supplier in the nation.
Learn more about Tennessee Valley Authority here
https://brainly.com/question/2894133
#SPJ4
Problem 1 (20 points) The beam
ABC
is subjected to a point load at the middle of segment
AB
and a uniformly distributed load at the segment
BC
, as shown in the figure. a) Find the equation of the elastic curve for the segment
AB
. b) Find the maximum absolute value of the deflection between the supports
A
and
B
c) Find the deflection at the middle of the segment
AB
d) Find the deflection at point C. Set
w 0 =3 N/m,L=2 m,EI=25000Nm^2
. Use the method of superposition for all parts. Hint: for
x>L/2
in segment
AB
, the solution can be obtained from the table by replacing
x
by
L−x
.
To solve this problem, use the superposition method, the total deflection at any point is the sum of the deflections due to the individual loads acting at that point.
a. we need to find the elastic curve equation for segment AB. This can be done by solving for beam deflection due to a point load in the middle of segment AB.
The beam deflection under a point load at distance x from the left support is given by
δ(x) = (w0x^2)/(24EI)
where w0 is the point load, E is the modulus of elasticity of the beam, and I is the moment of inertia of the beam.
Inserting the given value will result in:
δ(x) = (3x^2)/(2425000) = x^2/2000
This is the elastic curve equation for segment AB, as there is a point load in the middle of the segment. For part (b), we need to find the maximum absolute value of deflection between supports A and B. The deflection due to a point load is symmetrical about the midpoint of the segment, so the maximum absolute deflection occurs at the midpoint. Substituting x=L/2=1 into the equation for the elastic curve gives:
δ(x) = (1^2)/2000 = 0.0005m
This is the maximum absolute deflection between supports A and B.
In part (c) we need to find the deflection in the middle of segment AB. Substituting x=L/2=1 into the equation for the elastic curve gives:
δ(x) = (1^2)/2000 = 0.0005m
This is the deflection in the middle of segment AB. In part (d) we need to find the deflection at point C. To do this, solve for the beam deflection due to the evenly distributed load on segment BC and add it to the deflection due to the point load at the middle of segment AB.
b. The deflection of a beam under a uniformly distributed load w per unit length is given by
δ(x) = (wx^3)/(48EI)
Inserting the given value will result in:
δ(x) = (3x^3)/(4825000) = x^3/3200
This is the equation for the elastic curve of segment BC as the load is evenly distributed.
c. To find the deflection at point C, we need to substitute x=L=2 into the elastic curve equation. This will tell you:
δ(x) = (2^3)/3200 = 0.00125m
d. To find the total deflection at point C, the deflection due to the point load at the center of section AB must be added to the deflection due to the evenly distributed load in section BC. Substituting x=L/2=1 into the equation for elastic curve due to point load, we get:
δ(x) = (1^2)/2000 = 0.0005m
Learn more about this on brainly.com/question/1288793
#SPJ4
malizegrades that receives a row array of test scores of arbitrary length and positive values, and produces two outputs
Normalize Grades:
function [norm Scores, average] = normalize Grades(scores)
m=max(scores);
norm Scores=(scores./m)*100;
average=mean(norm Scores);
end
scores = [90, 45,76,21,85,97,91,84,79,67];
[norm Scores, average] = normalize Grades(scores)
Calculate the average of the normalized scores by scaling the provided scores to a linear scale from 0 to 100. Find the highest score among the provided scores, then use that value to normalize each score between 0 and 100. Utilize mean to determine the normalized score average. Analyze the data set. It makes sense to "normalize" scores in order to make them fit under a normal curve if you assume that they should. Additionally, for conformity's sake, very high scores must be reduced downward during normalization. In either case, some information is lost and data are corrupted. Since grades may be given based on how far above or below 0 each final Z-score ends up after normalization, this approach substantially simplifies both determining one's relative standing in the class and assigning grades.
Learn more about Normalize Grades here
https://brainly.com/question/27900432
#SPJ4
Which of these is true for prototypes?
a. Horizontal Prototypes does some processing apart from the required for presenting the productâs user interface
b. Vertical Prototype realizes part or all of a productâs user interface
c. All of the mentioned
d. None of the mentioned
Answer:c
Explanation:
a(n) ____ is any numeric variable you use to count the number of times an event has occurred.
It is incremented each time the event happens, providing a count of the number of times the event has happened.
Using Counters to Track Frequency of EventsA counter is a useful tool for tracking the frequency of events. By incrementing the counter each time the event occurs, it provides a numerical value that can be used to measure the number of times the event has occurred. Counters can be used to track a wide range of events, from the number of visitors to a website, to the number of times a certain keyword is used in a document. They are also useful for measuring patterns of behavior, as the counter can be set to reset at specific intervals to measure how often the event occurs over time.
Learn more about counters: https://brainly.com/question/1581078
#SPJ4
Robots can be classified into five groups. The code used for these classifications consists of a set of _____ letters, which refer to types of robot joints.
The code used for robots classifications consists of a set of three letters.
What is robots classifications?Robot classifications is classification for robot depend on their function and capabilities.
Autonomous Mobile Robots (AMRs) is first classification of robot for robot that have limited human intervention or input and can move mobile freely with calculation to make decision in near real-time.
Automated Guided Vehicles (AGVs) is second classification of robot for robot like AMRs but need more human input for deciding their paths so it can't move freely.
Articulated Robots is third classification of robot for robot that can emulated human body parts and their function.
Humanoids is next classification of robot for robot that have form like human and human center oriented. It is similar to AMRs except to their form that like human.
Cobots is last classification of robot for robot that must have human input to perform, this robot can't autonomous to perform but it will help human to complete their task.
Learn more about robot here:
brainly.com/question/27571415
#SPJ4
scan millions of websites to identify individual webpages that contain a specific word or phrase and then attempt to rank the results from most useful to least useful
Search Engines scan millions of websites to identify individual web pages that contain a specific word or phrase and then attempt to rank the results from most useful to least useful.
For your content to show up in search results, search engines must first be able to see it.
In order to operate, search engines must do three essential tasks:
Crawling: Search the Internet for content while reading the code and content of each URL you come across.
Indexing: Archive and arrange the information gathered through the crawling operation. After being indexed, a page has a chance of responding to pertinent searches.
Ranking: Provide the material that best responds to a searcher's query; therefore, results are ranked from most to least pertinent.
To learn more about Websites click here:
brainly.com/question/15601340
#SPJ4
Which of the following cable types often includes a solid plastic core that keeps the twisted pairs separated?Cat 6Cat 3Cat 5eCat 5
The twisted pairs are kept apart in cat 6 cables by a solid plastic core, which also helps to prevent the cable from being bent too tightly.
Computer networks that can send data at speeds of one Gbps, 1000 Mbps, or more typically employ Cat 6 cables. The following traits apply: consists of four sets of copper wires, each of which is used in data transmission.
offers a speed of up to 10 Gbps, a bandwidth of 250 MHz, and a length that can be extended to 100 metres.
compares favourably to earlier twisted pair cable variants in terms of better crosstalk and attenuation protection.
Ethernet networks like 10BaseT, 100Base-TX, 1000 Base-T, and 10 GBase-T can use the Cat 6 cable.
Know more about Computer networks here:
https://brainly.com/question/13992507
#SPJ4
the goal of one-shot learning is to find values for the weights wi using a large provided set of training data. once those weights have been found, they can be used to estimate prices for additional houses.
One-shot learning is an ML-based object classification algorithm that assesses the similarity and difference between two images. It's mainly used in computer vision.
One-shot learning aims to educate the model how to make its own inferences about the similarities between them based on the fewest possible pictures. One-shot learning is a common issue with object classification in computer vision. One-shot learning seeks to categorise things from one or a small number of instances, in contrast to the majority of machine learning-based object categorization algorithms that need training on hundreds or thousands of examples. When a machine is trained to learn from data without ever having to view the data itself, this process is known as zero-shot learning. Few-shot learning is the process of teaching a computer how to utilise data to learn from a particular perspective. A computer may be taught to learn from data using both zero-shot and few-shot learning techniques.
To learn more about One-shot learning click the link below:
brainly.com/question/29806553
#SPJ4
when assembling a steel-lattice tower, what two references are needed to determine the location of each individual piece of steel?
To locate each individual piece of steel, we need to know the locations of the two references:
1. Detailed engineering drawings that specify the exact location, size, and shape of each piece of steel.
2. Structural calculations that define the force and stress requirements of each piece of steel.
What is steel?
Steel is a strong and durable metal alloy composed of iron and carbon. It is one of the most widely used metals in the world, with applications spanning from construction and architecture to industrial machinery and vehicles. Steel is also one of the most recycled materials in the world and can be reused in various ways. Steel is often used in construction due to its high strength-to-weight ratio, its ability to withstand strong forces and its resistance to corrosion. It can be formed into a variety of shapes and sizes, allowing for its use in everything from bridges and skyscrapers to cars and ships. Steel is also known for its malleability, allowing for it to be bent and molded into a variety of shapes and sizes. Steel is also ideal for use in heavy machinery and automobiles due to its strength and durability. Steel is also used to make a variety of everyday items such as cutlery, kitchen utensils, and tools. Steel is also widely used in the production of food cans, containers, and other packaging materials.
To learn more about steel
https://brainly.com/question/28782967
#SPJ4
the repetition structures we have discussed this week can be used interchangeably; however, there are a few occasions when one is clearly preferable to another. discuss, in detail as well as illustrate with an example, how to determine which structure to use when there is no clear indication. additionally, how much of the choice should be based on personal preference and how much on conventional practices?
When a program needs to process one or more instructions repeatedly until a condition is met, at which point the loop stops, repetition structures, sometimes known as loops, are utilized.
Numerous programming tasks are monotonous and rarely differ from one another. Counting and accumulating running totals, repeatedly accepting input data, and recalculating output values that only stop upon entry of a designated value are a few examples of such repetition. Another is the continuous checking of user data entries until an acceptable entry, such as a valid password, is made. Depending on the loop termination criterion, these repetition control structures can be used to repeatedly run the statements in the loop body.
Learn more about input here-
https://brainly.com/question/24179864
#SPJ4
Identify the true statement for the given 3-bit shift-right and load register if Dis 011, shr_in is 1, shr is 1. Id is o, and Q is 010. Consider arising clock edge. shr_in D shr ld 3-bit shift-right/load register O I. The present value is shifted: therefore, Q becomes 101 O II. The present value is shifted; therefore, Q becomes 111 O III. The present value of D is loaded into Q: thus, Q becomes 011 O IV. The present value of Q is maintained; therefore, Q remains 010
A 0 is added on the other end and the least-significant bit is lost when shifting right using a logical right shift. A single logical right shift divides a positive number by 2, discarding any remainders, for positive values.
The right shift (>>) operator returns the signed integer represented by the outcome of executing a sign-extending shift to the right by the number of bits provided in the second operand, modulo 32, of the binary representation of the first operand (evaluated as a two's complement bit string). The result will be 14 / 4 = 3 if I move the number 14 by two positions to the right. Since it's an integer, i.e. 14/4 = 3.5, the fractional component will not be taken into account. Generally speaking, the result of shifting a number n times to the right will equal number / (2n). The shift-bit expression's pattern is moved to the right by the amount supplied by additive-expression when using the right-shift operator.
To learn more about single logical click the link below:
brainly.com/question/28713173
#SPJ4
Neo-luddites argue that the technologies such as computers, automobiles, internet etc. are necessary and they have made significant improvement in our life.
TRUE OR FALSE
Neo-luddites argue that the technologies such as computers, automobiles, internet etc. are necessary and they have made significant improvement in our life. [FALSE]
What is Neo-LudditeA Neo-Luddite is someone who believes that the use of technology has serious ethical, moral, and social ramifications. Operating under this belief, Neo-Luddites are critical of technology and cautious to promote its early adoption. While they are not necessarily opposed to technology, they would prefer to see a more serious discussion of the role of technology in society. Some Neo-Luddites actually dislike technology, opting for a life of "voluntary simplicity," but this is not always the case.
The term "Luddite" comes from a political movement during the Industrial Revolution. The Luddites disliked the spread of mechanical devices such as mechanized looms to accomplish tasks which were formerly performed by people. They held marches, destroyed factories, and engaged in other types of activism in an attempt to prevent further technological development. Ultimately, the Luddites were unsuccessful, but when people started to question technology in large numbers again in the 1970s, they revived the concept, calling themselves the "New Luddites," and the Neo-Luddite movement was born.
t necessarily refer to themselves as Neo-Luddites, although some do. Instead, it is often used in a deprecating way by advocates of technology, to suggest that the thinking of Neo-Luddites is outdated and outmoded. The fantastic failure of the original Luddite movement is sometimes cited as an argument that opposition to technology is ultimately fruitless.
Learn more about Neo-luddites at https://brainly.com/question/29534867.
#SPJ4
Is there a way to know whether the model I downloaded is made using a pirated copy of Solidworks/ Autodesk Etc?
Answer:
NO
Explanation:
No, there is no way to know if the model you downloaded was made using a pirated copy of Solidworks or Autodesk. It is possible to download free models from legitimate sources such as 3D Warehouse, but it is also possible to download models from sites that are known to host pirated models. The only way to be sure that you are downloading a legitimate model is to purchase it from an authorized source.
which is one of the best structures for holding oil? group of answer choices anticline syncline normal fault reverse fault
An "anticlinal" trap is one of the most effective structures for forming a petroleum reservoir. An impermeable layer of rock forms a cap over a layer of porous permeable sedimentary rock in this location. If petroleum is present, it drifts upward and becomes trapped within the anticline fold.
What is a anticlinal trap structure?
An anticline is the structural-trap formed by the rock strata folding into an arch-like shape. The rock layers in an anticlinal trap were originally laid down horizontally before folding into an arch-like shape known as an anticline due to earth movement.
This type of structure can be seen on a seismic section, but because seismic sections are typically 'time sections,' the actual structure can be obscured by velocity changes above the anticline. The structural contours of an anticline form closed loops.
To know more about seismic section, visit: https://brainly.com/question/28900452
#SPJ4
Consider a Couette flow with a pressure gradient. A plate, located a distance H above a solid wall, is moving with a velocity Ve. Furthermore, a constant pressure gradient, (dp/dx), is imposed in the x direction. It can be assumed that the plate and the wall extend to infinity. Assume incompressible steady flow of a Newtonian fluid with a constant viscosity u and neglect gravity. у (a) Determine the velocity profile in the fluid. (List the Plate assumptions and simplifications you make, and clearly show ►U which ones are used to drop terms in the governing H equations.) X (b) Find the non-zero components of the viscous stress throughout the fluid. wall (c) At what value of the pressure gradient, (dp/dx)a, is the shear stress at the plate equal to zero? (d) At what value of the pressure gradient, (dp/dx)p, is the shear stress at the wall equal to zero? (e) Make a neat qualitative sketch of the velocity profile for each of the following cases: i. (dp/dx) = 0 ii. (dp/dx) = (dp/dx)a iii. (dp/dx) = (dp/dx)}
(a) The velocity profile in the fluid or u is:
[tex]$$u=U_e\left(\frac{y}{H}\right)+\frac{1}{2 \mu}\left(\frac{\partial P}{\partial x}\right)\left(y^2-H y\right)$$[/tex]
(b) The value of the pressure gradient for which the shear stress on the wall is equal to zero is:
[tex]& \frac{\partial P}{\partial x}=\frac{-U_\theta \mu}{H\left(y-\frac{H}{2}\right)}\end{aligned}$$[/tex]
What is pressure gradient?The pressure gradient, which is a physical quantity used in atmospheric science to describe the direction and rate at which pressure rises most quickly around a specific location, is typically defined as being of air, but it can also more broadly refer to any fluid.
Pascals per meter (Pa/m) is a dimensional unit used to express the pressure gradient. The gradient of pressure as a function of position is what it is mathematically referred to as. The force density is the name for the negative gradient of pressure.
Pressure gradients in petroleum geology and petrochemical sciences pertaining to oil wells, and more specifically in hydrostatics, refer to the gradient of vertical pressure in a column of fluid within a wellbore and are typically expressed in pounds per square inch per foot (psi/ft).
Learn more about Pressure gradients
https://brainly.com/question/13383197
#SPJ4
a breakwater along an oceanfront is to be constructed of concrete, and the formwork for retaining the concrete while it is poured is shown. for every 6 ft of width (into the plane of the figure), the formwork has a horizontal support bc and a support df. the stakes at points a, e, and f may be modeled as pins, and the weights of all members except the concrete may be neglected.
NOTE: This is a muiti-part question. Once an answer is submitted, you will be unable to return to this part.
If the concrete is modeled as a fluid with
180lb/ft3 specific weight, determine the force supported by members BC and DF
The force supported by the member
BC is ...........lb. (Round the final answer to four decimal places.) The force supported by the member DF is ..........lb.
An extensive presentation covering the overall concept of formwork, the numerous types, the most recent developments, and a comparison of traditional and modern formwork.
It also covers the analysis of formwork failure factors and safety precautions to be implemented to avoid failure. Structures under dead loads experience consistent weight over time. The self-weight of structural components including walls, plaster, ceilings, floors, beams, columns, and roofs is one of them. Dead loads also comprise the weight of any fixtures that are affixed to the building system permanently. Members are initially scaled based on architectural drawings and other pertinent documents before being analyzed and designed, and their weights are calculated using the data included in the majority of codes.
Learn more about system here-
https://brainly.com/question/27162243
#SPJ4
the video discusses four potential models of how the expansion of the universe changes with time. drag the correct model description from the left-hand column to the appropriate blank in the sentences in the right-hand column. use each term only once.
The coasting model assumes that the expansion rate of the universe always stays the same.
All four models predict that the universe is expanding today.
The recollapsing model predicts that the universe will someday contract.
The critical model predicts that the average density of mass in the universe is exactly the critical density.
The accelerating model predicts that the universe is expanding faster now than it was in the distant past.
What is the model about?This type of thinking can be practiced using a critical thinking model. It provides guidelines for asking the right questions, coming to logical conclusions, and explaining how we did it all while assisting us in recognizing our own thinking biases and enabling us to attempt viewing the world objectively.
An acceleration model is a type of model that forecasts time-to-failure as a function of operating stresses. Models of physics or kinetics that describe the failure mechanism are frequently used to create acceleration models. Acceleration models typically draw their foundation from the physics or chemistry of a specific failure mechanism.
Learn more about model on:
https://brainly.com/question/17764105
#SPJ1
classical conditioning is the study of behaviors that are____ , whereas operant conditioning studies behaviors that are____
Operant conditioning examines proactive behaviour, whereas classical conditioning examines reactive behaviour.
That is what type of an operant is it?A rat clicking its lever with response to food, an infant screaming in relation to maternal care, or small talk in response to the social engagement are all examples of operant responses.
What is the operant concept?Operant conditioning is based on the fundamental idea that a sensory antecedent somehow triggers an action, which in turn triggers a result. This kind of training makes use of primary, supplementary, and generalised reinforcers—both positive and negative. Food, shelter, and/or water are the 3 main reinforcers.
To know more about Operant visit :
https://brainly.com/question/13144439
#SPJ1
The dresser has a weight of 80 lb and is pushed along thefloor. If the coefficient of static friction at Aand B is μs = 0.3 and thecoefficient of kinetic friction is μk =0.2, determine the smallest horizontal force P needed tocause motion. If this force is increased slightly, determinethe acceleration of the dresser. Also, what are the normalreactions at A and B when it begins to move?
The normal reactions at A and B when the dresser begins to move will be:
Normal Reaction at A = μs * mg = 0.3 * (80 lb) * 32.2 ft/s² = 96.6 lb
Normal Reaction at B = μk * mg = 0.2 * (80 lb) * 32.2 ft/s² = 64.4 lb
What is reaction?
Reaction is an action taken in response to a particular stimulus. It is the way in which people interact with the world around them. Reactions can be physical, mental, or emotional in nature. It is the way in which individuals respond to situations, people, and events. Reactions can range from positive to negative, and can even be neutral. Reactions are affected by a person's past experiences, beliefs, values, and emotional state. It is also influenced by external factors such as the environment, other people, and media. Reactions are an important part of social interaction and communication, as they provide feedback and help build relationships. They also provide insight into a person's personality, character, and values. Reactions are the building blocks of relationships, and it's important to be aware of how one's reactions affect others.
The smallest horizontal force P needed to cause motion is:
P = μs * mg = 0.3 * (80 lb) * 32.2 ft/s² = 96.6 lb
When the force is increased slightly, the acceleration of the dresser will be:
a = (P - μk * mg) / m = (96.6 - 0.2 * (80 lb) * 32.2 ft/s²) / (80 lb) = 7.7 ft/s²
The normal reactions at A and B when the dresser begins to move will be:
Normal Reaction at A = μs * mg = 0.3 * (80 lb) * 32.2 ft/s² = 96.6 lb
Normal Reaction at B = μk * mg = 0.2 * (80 lb) * 32.2 ft/s² = 64.4 lb
To learn more about reaction
https://brainly.com/question/19260256
#SPJ1
which of the following dot matrix printer components converts impulses into physical movements that cause small hammers to strike the printhead?
A: An electromagnet component of the dot matrix printer converts impulses into physical movements causing small hammers to strike the printhead.
Dot matrix printers also known as impact printers function by physically striking the printhead to the print surface like an old-fashioned typewriter. An inked ribbon is put between the printhead and the surface and then an inked impression is left behind. On a dot matrix printer, an electromagnetic impulse enables a small hammer to create the strike. Whenever the printer obtains data for a print job, the logic board produces a series of electric impulses. An electromagnet then converts impulses into physical movements for small hammers to strike the printhead appropriately.
"
Complete question is:
which of the following dot matrix printer components converts impulses into physical movements that cause small hammers to strike the printhead?
A: electromagnet
B: dot
C: hammer
D: ink ribbon
"
You can learn more about dot matrix printer at
https://brainly.com/question/14551097
#SPJ4
A ramjet has a constant-diameter combustion chamber followed by a nozzle whose throat diameter is 0.94 times the chamber diameter. Air enters the combustion chamber with T, 1450 K and M-0.3. How high may the temperature rise in the combustion chamber without necessarily changing the chamber inlet conditions? For simplicity, neglect frictional losses in the chamber and nozzles and assume that the working fluid has a specific heat ratio of 1.333.
The temperature of the air passing through the combustion chamber may increase to 2567 K. The amount of temperature increase will depend on the expansion ratio of the nozzle, as well as the specific heat ratio of the working fluid.
The temperature rise in a ramjet's combustion chamber is determined by the ratio of the area at the throat of the nozzle to the area of the inlet to the combustion chamber. The temperature of the air entering the combustion chamber will remain constant as long as the inlet conditions remain the same. However, the temperature of the air will increase as it passes through the combustion chamber and expands in the nozzle, resulting in an increase in temperature.
The maximum temperature increase in the combustion chamber can be calculated using the following formula:
Tmax = Tin x (gammaⁿ)
Where
Tmax = the maximum temperature increase in the combustion chamber. Tin = the inlet temperature of the air entering the chamber.
Gamma = the specific heat ratio of the working fluid.
n = the expansion ratio of the nozzle.
In the given example, the maximum temperature increase in the combustion chamber would be calculated as follows:
Tmax = 1450 K x (1.333²) = 2567 K.
Learn more about temperature, here https://brainly.com/question/11464844
#SPJ4
a building is considered green from an environmental standpoint for all the following reasons except: A. IT WAS PAINTED USING A VOLATILE ORGANIC COMPOUNDS (VOC) -BASED GREEN PAINT. B. IT IS MORE ENERGY EFFICIENT THAN CONVENTIONAL HOMES. C. IT MINIMIZES THE RELEASE OF TOXIC SUBSTANCES D. IT IS CONSTRUCTED WITH MOSTLY RECYCLABLE MATERIALS
All of the following, with the exception of option a, qualify a building as green from an environmental perspective: it was painted with a volatile organic compound (VOC) based - green paint.
What environmental benefits may green buildings provide?Green neighborhoods and structures promote the creation and maintenance of vegetated land and roof surfaces as well as the reduction of waste disposed of in landfills. High-performing green buildings, especially those that have earned the LEED certification, provide a way to decrease the impact of both residents and buildings on the environment.
What are the top 5 green building products?Green construction techniques
Stone. Living in a stone building is low maintenance and environmentally friendly, and any leftover stone from the construction may be used to finish the home with countertops or tile.
Cob, bamboo, cork, adobe brick, straw bales, cordwood, and earth bags are some examples of building materials.
To know more about organic compounds visit:
https://brainly.com/question/5994723
#SPJ1
when hammer test is preferable than concrete cubic test?
Answer:
Rebound Hammer test is a Non-destructive testing method of concrete which provide a convenient and rapid indication of the compressive strength of the concrete. The rebound hammer is also called as Schmidt hammer that consist of a spring controlled mass that slides on a plunger within a tubular housing.
The operation of rebound hammer is shown in the fig.1. When the plunger of rebound hammer is pressed against the surface of concrete, a spring controlled mass with a constant energy is made to hit concrete surface to rebound back. The extent of rebound, which is a measure of surface hardness, is measured on a graduated scale. This measured value is designated as Rebound Number (rebound index). A concrete with low strength and low stiffness will absorb more energy to yield in a lower rebound value.
The ______ must be placed on timbers or cribbed so as to spread the weight of the crane and the load over a large enough area.
Note that the outrigger must be placed on timbers or cribbed so as to spread the weight of the crane and the load over a large enough area.
What is an outrigger and what is it used for?An outrigger is a device that is used to provide stability and support for a structure or vehicle. It consists of a beam or frame that extends horizontally from the main body of the structure or vehicle, usually supported by one or more additional beams or poles that are attached to the ground or other surfaces.
An outrigger or double-hull watercraft produces stability owing to the distance between its hulls rather than the form of each individual hull, as opposed to a single-hulled vessel.
Outriggers are used for a number of purposes, including:
Outriggers are commonly used on boats and ships to give additional stability and support, especially in strong seas.Cranes utilize outriggers to assist balance the cargo being hoisted and keep the crane from tipping over.Outriggers are employed on a variety of construction equipment, including excavators and bulldozers, to offer stability when working on uneven terrain.Learn more about outrigger:
https://brainly.com/question/23653582
#SPJ1
engineers may issue subjective and partial statements if such statements are in writing and consistent with the best interests of their employers, clients, or the public..
A. True
B. False
The statement for engineers may issue subjective and partial statements if such statements are in writing and consistent with the best interest of their employers, clients, or the public is false.
Engineers is a profession that focus to solve technical problem or develop solution for the problem with applied science and mathematics theories and/or principles.
Science and mathematics theories and/or principles is based on the actual facts or objective. So, engineers must put objectivity in their work.
Engineers also objective and issue the full statement in order to give solution to their clients or public problem. If the statement is subjective or partial in any form including writing is wrong because it can't solve clients or public problem.
Learn more about engineers here:
brainly.com/question/7447774
#SPJ4
Let P(x) and Q(x) be predicates and suppose D is the domain of x. For the statement forms in each pair, determine whether (a) they have the same truth value for every choice of P(x), Q(x), and D, or (b) there is a choice of P(x), Q(x), and D for which they have opposite truth values.
Answer:
just use the formal man .
if you need to weld two pieces of aisi 1018 cd steel together, what will be the yield strength of the steel in the vicinity of the weld in units of kpsi?
if you need to weld two pieces of AISI 1018 cd steel together, the yield strength of the steel in the vicinity of the weld will be 64 kpsi.
What is yield strength?Yield strength is a measure of the maximum stress that a material can withstand without deforming. It is a practical approximation of the elastic limit and is defined as the stress at which a material exhibits a specified permanent deformation.
Yield strength is critical in structural engineering. When designing a component, for example, it must support the force incurred during use and must not deform plastically. To put it another way, a material with adequate yield strength should be chosen.
The yield strength is often used to calculate the maximum permissible load in a mechanical part because it represents the upper limit to forces that can be applied without causing permanent deformation. A variety of yield criteria for various materials have been established.
Learn more about yield strength
https://brainly.com/question/13259307
#SPJ4
during the capture stage of the data life cycle, a data analyst may use spreadsheets to aggregate data.
During the capture stage of the data life cycle, a data analyst may use spreadsheets to aggregate data: False.
What is DLC?In Computer technology, DLC is an abbreviation for data life cycle and it can be defined as a strategic methodology that defines the sequence of stages that a given unit of data goes through from inception (collection) to its eventual deletion (destruction) at the end of its useful life.
In Computer technology, there are six (6) steps in a data life cycle and these include the following:
PlanCaptureManageAnalyzeArchiveDestroyDuring the analyze stage of the data life cycle, a spreadsheet application may be used by a data analyst in order to aggregate data.
Read more on data life cycle here: brainly.com/question/28039445
#SPJ1
Complete Question:
During the capture stage of the data life cycle, a data analyst may use spreadsheets to aggregate data. True or False.
A cylindrical piece of steel 25 mm (1.0 in.) in diameter is to be quenched in moderately agitated oil. Surface and center hardnesses must be at least 55 and 50 HRC, respectively. Which of the following alloys will satisfy these requirements: 1040, 5140, 4340, 4140, and 8640? Justify your choice(s). Use the following figures as necessary
The following alloys 8660,8640,4140,4340 and 5140. A metal alloy is a material that combines multiple metals or combines a metal with non-metallic components.
In water that is only slightly stirred, a cylindrical piece of steel is to be quenched. The minimum required surface and centre hardness is:
[tex]H_{sur}=50[/tex] HRC
[tex]H_{c}[/tex]=40HRC
D=50 mm
Given alloys: 1[tex]040, 5140, 4340, 4140, 8620, 8630, 8640,[/tex]and [tex]8660[/tex].
Quenching cylindrical bars in slightly disturbed water:
Since the centre hardness of 8660,8640,4140,4340, and 5140 is greater than 40 HRC and the surface harness is greater than 50HRC, they are eligible. There must be at least one metal in a mixture of chemical elements known as an alloy. The qualities of a metal, such as electrical conductivity, ductility, opacity, and shine, will all be kept in the alloy's ultimate product, unlike chemical compounds with metallic bases. An alloy may, however, also possess extra qualities not seen in pure metals, including greater strength or hardness. In certain cases, an alloy may maintain essential properties while lowering the material's overall cost. In other cases, the combination gives the individual metal elements added benefits like corrosion resistance or mechanical strength.
Learn about alloys here
https://brainly.com/question/24842164
#SPJ4
the program segment below is intended to move a robot in a grid to a gray square. the program segment uses the procedure goalreached, which evaluates to true if the robot is in the gray square and evaluates to false otherwise. the robot in each grid is represented as a triangle and is initially facing left. the robot can move into a white or gray square but cannot move into a black region. a 15-line code segment reads as follows. line 1: repeat until, open parenthesis, goal reached, open parenthesis close parenthesis, close parenthesis. line 2: open brace. line 3: if, open parenthesis, can underscore move, open parenthesis, forward, close parenthesis, close parenthesis. line 4: open brace. line 5: move underscore forward, open parenthesis close parenthesis. line 6: close brace. line 7: if, open parenthesis, can underscore move, open parenthesis, right, close parenthesis, close parenthesis. line 8: open brace. line 9: rotate underscore right, open parenthesis close parenthesis. line 10: close brace. line 11: if, open parenthesis, can underscore move, open parenthesis, left, close parenthesis, close parenthesis. line 12: open brace. line 13: rotate underscore right, open parenthesis close parenthesis. line 14: close brace. line 15: close brace. for which of the following grids does the program not correctly move the robot to the gray square?
The correct answer is Although the program will not move the robot to the gray square in Grid II, it will correctly move the robot to the gray square in Grid I. This option is correct.
A simulation enables exploration of a phenomena without the time, safety, or financial constraints of the actual world. Both the first value and the second value are true. These industrial robots have three prismatic joints that slide along three perpendicular axes to produce linear motion (X, Y and Z). In order to provide rotational movement, they could additionally include an attached wrist.While the programme is running, values are entered using the input statement.Robots that do not have servo motors are used to position and move items. This implies that these robots will be able to pick up, transfer, and then set down objects.
To learn more about gray square click the link below:
brainly.com/question/29172488
#SPJ4