(a) The velocity profile in the fluid or u is:
[tex]$$u=U_e\left(\frac{y}{H}\right)+\frac{1}{2 \mu}\left(\frac{\partial P}{\partial x}\right)\left(y^2-H y\right)$$[/tex]
(b) The value of the pressure gradient for which the shear stress on the wall is equal to zero is:
[tex]& \frac{\partial P}{\partial x}=\frac{-U_\theta \mu}{H\left(y-\frac{H}{2}\right)}\end{aligned}$$[/tex]
What is pressure gradient?The pressure gradient, which is a physical quantity used in atmospheric science to describe the direction and rate at which pressure rises most quickly around a specific location, is typically defined as being of air, but it can also more broadly refer to any fluid.
Pascals per meter (Pa/m) is a dimensional unit used to express the pressure gradient. The gradient of pressure as a function of position is what it is mathematically referred to as. The force density is the name for the negative gradient of pressure.
Pressure gradients in petroleum geology and petrochemical sciences pertaining to oil wells, and more specifically in hydrostatics, refer to the gradient of vertical pressure in a column of fluid within a wellbore and are typically expressed in pounds per square inch per foot (psi/ft).
Learn more about Pressure gradients
https://brainly.com/question/13383197
#SPJ4
What type of wrench surrounds and grips all corners when loosening and tightening bolts and nuts?
The type of wrench that surrounds and grips all corners when loosening and tightening bolts and nuts is known as box-ends.
What are wrenches used for?Wrenches are significantly used for loosening and tightening of fasteners. These are typically a kind of tool that is used to provide grip and mechanical advantage in applying torque to turn objects—usually rotary fasteners, such as nuts and bolts—or keep them from turning.
According to the context of this question, there are basically two major kinds of wrenches: Pipe wrenches used in plumbing for gripping round (cylindrical) things. General-use wrenches are used on nuts and bolts that have flat, parallel surfaces; e.g., square or hexagonal (hex).
Therefore, box-ends are a type of wrench that surrounds and grips all corners when loosening and tightening bolts and nuts.
To learn more about Technological tools, refer to the link:
https://brainly.com/question/25860017
#SPJ1
steel mill inc., employs five hundred workers. for the occupational safety and health administration, steel must do all of the following except
Allow workers to go without the necessary safety gear.
What is Steel Mill Inc.?Steel Mill Inc. is required to abide by all Occupational Safety and Health Administration (OSHA) rules and regulations, which include offering a secure workplace and educating staff members about safety procedures.This entails furnishing safety gear, such as hard helmets, gloves, and other protective apparel, as well as carrying out routine safety inspections and keeping current records of any occupational illnesses or injuries.The Occupational Safety and Health Administration does not, however, mandate that Steel Mill Inc. provide its staff time off for vacation or illness. Although Steel Mill Inc. may decide to do this, OSHA does not mandate it.Additionally, Steel Mill Inc. is not required to provide any benefits to its workers, such as health insurance or retirement programs. These are optional perks that companies may provide; OSHA does not require them.
To learn more about Steel Mill Inc. refer to:
https://brainly.com/question/29426067
#SPJ4
either ellie is elected without debating the incumbent or herbie debates the incumbent without being elected
If Ellie is elected without debating the incumbent, then Herbie will not be elected as he has not had the chance to debate the incumbent.
What do you mean by incumbent?
Incumbent is a term often used in politics and business to refer to a person who holds an office or position. In politics, it refers to the person currently in office, such as the current president or prime minister. In business, it refers to the current holder of a position, such as the CEO or chairman of a company. It can also refer to the current holder of any title or position.
The use of the term incumbent Incumbent is a term often used in politics and business to refer to a person who holds an office or position. In politics, it refers to the person currently in office, such as the current president or prime minister. In business, it refers to the current holder of a position, such as the CEO or chairman of a company. It can also refer to the current holder of any title or position.
The use of the term incumbent suggests that the holder of the position has a certain that the holder of the position has a certain authority or status. This can be used to indicate the importance of a position, or to emphasize the current holder's qualifications. It can also be used to refer to someone who has an advantage in a particular situation.
However, if Herbie does debate the incumbent without being elected, then he may still be able to gain more support from the voting public and even potentially win the election.
To learn more about incumbent
https://brainly.com/question/28995570
#SJP4
you have a network that's connected using a physical bus topology. one of the cables that connects a workstation to the bus breaks.
When a network is connected using a physical bus topology and a cable that connects a workstation to the bus breaks then no devices will be able to communicate.
What is a bus topology?
A type of network design known as bus topology, often referred to as line topology, connects all devices in the network with a single coaxial or RJ-45 network wire. The term "bus," "backbone," or "trunk" refers to the single wire that connects all of the devices and transmits all of the data.
Bus topology is one of the simplest physical topologies used in networks, according to the definition. Famously, the Local Area Network uses the bus topology. All of the nodes in this topology are linked together by a single wire known as the "Backbone."
To learn more about a bus topology, use the link given
https://brainly.com/question/13501206
#SPJ4
Server (40 points): The server will contain the main(String[] args) method and will instantiate an instance of the Word Searcher object defined above. After that it will open a Server Socket and bind it to an available port. For my own system the port 1236 was open, but this may be different on your home computer. The server will sit in a while loop performing the following steps: 1. Accept client socket connection 2. Set up input/output streams from client connection 3. Read in String from client 4. Pass String to WordSearcher object, receive List output 5. Transmit Listsinteger> to client 6. Close Connection 7. Return to top of while loop Recommended communication format is detailed below. If you want to include a special "shutdown" command that causes the server to exit its while loop that is fine. You may also have while(1) to make a loop that runs forever and must be shut down manually in Eclipse.
Here is a sample of how the server would be implemented
import java.io.*;
import java.net.*;
import java.util.*;
public class Server {
public static void main(String[] args) {
WordSearcher searcher = new WordSearcher();
try {
// Bind server socket to a port
ServerSocket serverSocket = new ServerSocket(1236);
System.out.println("Server socket created, waiting for clients...");
while (true) {
// Accept client connection
Socket clientSocket = serverSocket.accept();
System.out.println("Client connected: " + clientSocket.getInetAddress());
// Set up input and output streams
BufferedReader in = new BufferedReader(new InputStreamReader(clientSocket.getInputStream()));
PrintWriter out = new PrintWriter(clientSocket.getOutputStream(), true);
// Read in string from client
String inputString = in.readLine();
// Pass string to WordSearcher object and receive list output
List<Integer> positions = searcher.search(inputString);
// Transmit list to client
for (Integer position : positions) {
out.println(position);
}
// Close connection
clientSocket.close();
}
} catch (IOException e) {
e.printStackTrace();
}
}
}
The implementation binds a server socket on port 1236 and listens for client connections. When a client connects, it sets up an input stream and an output stream for communicating with the client. It then reads a string from the client, passes it to a Word Searcher object to search for words, and sends a list of resulting positions to the client. Finally the connection is closed and it loops back to wait for the next client connection.
To include a special "shutdown" command, loop checking for that command, then break out of the loop and close the server socket when the command is received. One can also use a flag variable that is set to true when the shutdown command is received, and use that flag to break out of the loop.
Read more about loops on brainly.com/question/29586204
#SPJ4
in a circuit, a voltage uo in the s-domain, i.e. vo (s), is given by: a) by examining just, the roots of the denominator what conclusions can you draw about the voltage uo (t) for t > 0. b) what would be the steady state value of the voltage uo (t) for t >> 0. c) use an inverse laplace transform and determine the expression of uo (t) in the time domain for t>0. d) plot the expression of uo (t) in the time domain for t>0. e) are your answers from part (a) and (b) agree in agreement with the plot in part (d).
The term "voltage divider" refers to a very popular and practical series resistor circuit. You will understand the origin of the moniker once we have figured out how this circuit functions.
Assume the divider is discharging 0000 current. (Before we are finished, we will investigate what would occur if this zero-current assumption were false.)
The bottom resistor is divided by the total number of resistors, scaling the input voltage to equal the output voltage.
For whatever value of textR1R1start text, R, 1, end text and textR2R2start text, R, 2, end text, the ratio of resistors is always less than 111. Because of this, v out v out v, start subscript, o, u, t, and end subscript are always smaller than v in v in v, start subscript, I and n, respectively. The input voltage is scaled down to v outv out v, start subscript, o, u, t, end subscript from v inv in v, start subscript, I n, and end subscript.
By a predetermined ratio set by the resistor values: v, start subscript, o, u, t, end subscript. The circuit is known as a voltage divider because of this.
Know more about output here:
https://brainly.com/question/9401357
#SPJ4
determine and its region of convergence. (b) determine (c) if keep the same system, but change the input , determine the output . h(t) x(t) h(s) y(t) , 2 2 ( ) -
The Region of Convergence is the area in the pole/zero plot of the transfer function in which the function exists.
The ROC of the Laplace transform X(s) for a left-sided signal x(t) is Re(s)2, where 2 is a constant. As a result, the ROC of a left-sided signal's Laplace transform lies to the left of the line =2. Receiver Operating Characteristic is what the word "ROC" refers to. Following the assault on Pearl Harbor in the 1940s, ROC curves were initially used to explore discriminator systems for the detection of radio signals in the presence of noise. The area of convergence is the set of values in the z-plane for which the ZT converges (ROC). S is a similar laplace variable, and its ROC is the value at which integration converges.
To learn more about Convergence click the link below:
brainly.com/question/15415793
#SPJ4
a hydrogen fuel cell–powered car driving on a highway is different from gasoline-powered cars because hydrogen fuel cell–powered cars only emit
Answer:
water vapor and heat
a machine administers medication dosage based on weight. write an if-elseif-else statement that assigns the appropriate dosageamount given userweight. weight (kg) dosage (units) --------------------------------------------------------- less than 50 10 50 - 140 20 greater than 140 30 ex: if userweight is 65, then dosageamount is assigned with 20.
Answer:
MATLAB function:
function dosageAmount=CalculateDosage(userWeight)
% user weight is in kg
dosageAmount=0;
% clears the variable dosageAmount
if userWeight<50
dosageAmount=10;
elseif userWeight <= 140
dosageAmount=20;
else
dosageAmount=30;
end
end
Code: >> CalculateDosage(65)
Refer to the image for more
Using the simplified lifting model illustrated in the figure you can estimate the compressive loads in the lower back (L5/S1 joint). The figure shows two loads acting on the body: the weight of the upper body of the person (HAT = Head, Arms, Trunk) and a weight that is being lifted (OBJECT). The moment arms for these 2 loads are the distances from each force vector to th L5/S1 joint. Enter your student ID to get your personalized values for HAT weight (weight_HAT), OBJECT Weight (weight_OBJECT), HAT moment arm (mmt_arm_HAT), OBJECT moment arm (mmt_arm_OBJECT), Sacral Angle (ang_Sacral), and MUSCLE moment arm (mmt_arm_MUSCLE). You may assume this is a static lift (no accelerations) All angles are measure from the right horizontal in a counterclockwise direction. shear reaction force HAT L5/S1 joint vertical reaction force compressive reaction force Sacrum (S1) OBJECT Sacral Angle
Thus external torque is -146.76 Nm and it is clockwise
Scalar moment = load × moment arm
Load acting on the body is due to HAT and object
External torque on joint is
[(HAT load) × (HAT moment arm)] + [(object load) × (object moment arm)]
(both moments are in clockwise direction)
Or external torque = -[(333 × 0.22) + (245 × 0.3)] = -146.76 Nm
Thus external torque is -146.76 Nm and it is clockwise.
This is so because the force and speed of the pistons' motion determine the torque. High levels of this torque force can be produced by the fastest cars at relatively low rpm. This enables speedy acceleration of the vehicle. The definition of torque is rF=rFsin(r). In other terms, torque is the cross product of the force vector and the distance vector, where 'a' is the angle between r and F. The distance vector represents the distance from the pivot point to the place where force is applied.
Learn more about torque here:
https://brainly.com/question/6855614
#SPJ4
a carpenter will be using 24" x 3/8" hand-split cedar shakes to cover a roof. the shakes will be applied with an average spacing of 1/2" between shakes...
The square feet of roof area that can be covered by one square of these shakes is 75%. The correct option D.
What is the weather?The condition of the atmosphere, including its temperature, pressure, wind, humidity, precipitation, and cloud cover, is referred to as the weather. It is distinct from climate, which is the average of all weather events for a certain location over a period of around 30 years.
Given Data,
Size of shakes = 24” x 3/8”
Weather exposure = 7 ½”
As explained above, 24” x 3/8” shakes with 7 ½” weather exposure has coverage of 75 square feet per square of shakes. 75 square feet
Therefore, the correct option D. 75%.
To learn more about weather, refer to the link:
https://brainly.com/question/22432988
#SPJ1
The question is incomplete. Your most probably complete question is given below:
The shakes will be applied with an average spacing of '/>" between shakes, and the weather exposure will be 71/2". Look at the shake coverage table. According to the information in this table, approximately how many square feet of roof area can be covered by one square of these shakes?
controlling the dynamics of three electron spin qubits in a donor-acceptor-radical molecule using dielectric environment changes
Answer:
Photogenerated entangled electron spin pairs provide a versatile source of molecular qubits. Here, we examine the spin-dependent dynamics of a covalent donor–acceptor–radical molecule, D-A-R•, where the donor chromophore (D) is peri-xanthenoxanthene (PXX), the acceptor (A) is pyromellitimide (PI), and the radical (R•) is α,γ-bisdiphenylene-β-phenylallyl (BDPA). Selective photoexcitation of D within D-A-R• in
Which of the following is NOT a type of software prototyping?
a. Static
b.throwaway
c.revolutionary
d.incremental
Answer:
c.revolutionary
Explanation:
"Revolutionary" is not a type of software prototyping. Software prototyping is the process of creating a preliminary model or version of a software program to test its functionality and gather feedback. There are several different types of software prototyping, including static, throwaway, and incremental, but "revolutionary" is not one of them.
We consider a DHKE protocol over a Galois fields GF(2^m). All arithmetic is done in GF(25) with P(x) = x^5 + x^2 + 1 as an irreducible field polynomial. The primitive element for the DiffieHellman scheme is a = x2. The private keys are a = 3 and b = 12. You will need to show your work and answer the following questions.
a. Show how Alice computes bA
b. Show how Bob computes bB
c. Show how Alice computes KAB
d. Show how Bob computes KBA
The Diffie-Hellman key exchange (DHKE) protocol is a method for securely exchanging a cryptographic key over an unsecured communication channel. In the DHKE protocol, Alice and Bob agree to use a specific Galois field, GF(2^m), and a primitive element, a, for their key exchange. In the case given, GF(25) is used and the primitive element is a = x^2.
To compute bA, Alice first needs to compute a^3 (since her private key is 3) and then raise that value to the power of 12 (since b = 12). In GF(25), the multiplication operation is performed by adding the exponents of the two field elements being multiplied and then taking the result modulo 25 (since the field polynomial is x^5 + x^2 + 1, the degree of the polynomial is 5, so the result of any multiplication operation must be less than 25).
First, we compute a^3 by taking the exponent of a (which is 2) and multiplying it by 3 mod 25:
a^3 = (a^2)^3 = (x^2)^3 = x^6 = x^1 = x
Next, we compute bA by taking a^3 and raising it to the power of 12 mod 25:
bA = (a^3)^12 = (x^1)^12 = x^12 = x^2 = a
Thus, the final value of bA is a.
To compute bB, Bob first raises the primitive element a to his private key b to obtain the shared secret:
bB = a^b = (x^2)^12 = x^24 = x^4
Since we are working in GF(2^5) with the irreducible polynomial P(x) = x^5 + x^2 + 1, we need to reduce the degree of x^4 modulo P(x) to obtain the final shared secret:
x^4 = (x^5 + x^2 + 1)q(x) + x^3 + x^2 + x + 1
Therefore, the shared secret bB = x^3 + x^2 + x + 1.
Learn more about DHKE protocol, here https://brainly.com/question/29376731
#SPJ4
which non-traditional machining process was designed to machine hard (greater than rockwell 45c) and brittle workpieces such as glass, sapphire, alumina, ferrite, piezoceramics, quartz, silicon carbide, and technical ceramics.
Laser machining is the non-traditional machining process designed to machine hard and brittle workpieces.
The Benefits of Laser Machining Hard and Brittle WorkpiecesIn the modern world, the need for precision machining of hard and brittle materials has become increasingly important. This is because many products and components require a high level of accuracy and strength in order for them to function properly. As a result, many machining processes have been developed to meet these needs. One such process is laser machining, which has proven to be an efficient and cost-effective way of machining hard and brittle materials such as glass, sapphire, alumina, ferrite, piezoceramics, quartz, silicon carbide, and technical ceramic.
The benefits of laser machining hard and brittle workpieces are numerous. First, laser machining enables high precision due to the extremely focused nature of the laser beam. Because of this, laser machining can produce intricate shapes and patterns with very tight tolerances. This ensures that parts and components are made to exact specifications. Additionally, the use of a laser beam also eliminates the need for tooling, which can be expensive and time-consuming.
Learn more about Laser machining :
https://brainly.com/question/13621353
#SPJ4
I need to find the Current Flow through each resistor in this Combo Circuit, so far I have gotten that the current total is .5A.
and the Resistance total is 10ohms.
Can anyone please help!
To find the current flow through each resistor in a combo circuit, you need to use Ohm's law and the principles of electrical circuits.
What is Combo Circuit?Ohm's law states that the current flowing through a circuit is directly proportional to the voltage applied and inversely proportional to the resistance of the circuit. This means that the current flowing through each resistor in the circuit can be calculated by dividing the total voltage applied by the total resistance of the circuit.In your case, you have already determined that the total current flowing through the circuit is 0.5A and the total resistance of the circuit is 10 ohms. Using these values, you can calculate the current flowing through each resistor in the circuit by dividing the total voltage applied by the resistance of each individual resistor.For example, if the circuit contains two resistors with resistances of 5 ohms and 3 ohms, respectively, the current flowing through each resistor would be 0.5A * (5 ohms / 10 ohms) = 0.25A for the 5 ohm resistor and 0.5A * (3 ohms / 10 ohms) = 0.15A for the 3 ohm resistor.In general, the current flowing through each resistor in a combo circuit can be calculated by dividing the total current flowing through the circuit by the number of resistors in the circuit, and then dividing the result by the resistance of each individual resistor. This will give you the current flowing through each resistor in the circuit.To learn more about Combo Circuit refer to:
https://brainly.com/question/14628398
#SPJ1
A function template allows a function a. to accept a variable number of parameters b. to accept parameters with different data types c. to return different data types d. to be generated at runtime
A function template allows a function to accept parameters with different data types
A function can take parameters of various data types thanks to a function template. You may build a single function definition that is compatible with several distinct data types by using function templates. the function produced from a function template by the compiler (generic function). The compiler will create an int function when we compile this code by using a reference from the template function. One or more type parameters can be specified in a class template and utilised throughout the class as needed. The template-parameters of the class template must come first, followed by the template-parameters of the member template, when specifying a member template of a class template that is defined outside of its class template specification. Why is a class template's code typically contained in a separate header file
Learn more about Function here:
https://brainly.com/question/17216645
#SPJ4
calculate the estimated weight of a round brilliant with the following dimensions: average diameter: 7.25 mm depth: 5.45 mm girdle thickness: very thick a. 1.83 cts b. 1.85 cts c. 1.88 cts d. 2.05 cts
The estimated weight of a round brilliant is a. 1.83 cts.
How to calculate weight of brilliant?Brilliant has many shape and to calculate the weight of brilliant has different formulas from one shape to another shape. Since, this case use round brilliant then the formula is,
weight = average diameter * average diameter * depth * 0.0061
= 7.25 * 7.25 * 5.45 * 0.0061
= 1.7474
Then, weight of a brilliant is also affected by its girdle thickness. For girdle thickness very thick and average diameter 7.25 mm we will multiply the previous result by 1.045. (use girdle thickness table to know the multiply value)
weight = 1.7474 * 1.045
= 1.826
= 1.83 carats
Learn more about weight here:
brainly.com/question/28441422
#SPJ4
Which of these statements regarding sensors is TRUE?a. Sensors are input devices.b. Sensors can be analog as well as digitalc. Sensors respond to some external stimuli.d. All of these
Answer:
All of the statements regarding sensors are true. Sensors are input devices that respond to some external stimuli, and they can be either analog or digital.
please mark as brainliest!
Explanation:
g select the right order of the flags from the given list after each statement (1,2,3) executes? mov ax,7ff0h add al,10h ;statement 1 add ah,1 ;statement 2 add ax,2 ;statement 3
The right order of the flags from the given list after each statement executes is (1,2,3)
what is order?
Order is a state of organized, systematic arrangement or sequence. It is the way in which a group of objects, items, or things are arranged or organized according to a specific set of principles or rules.
Order is commonly found in nature, in art, in music, in mathematics, in society, and in other areas. It helps to create a sense of purpose, structure, and organization in a variety of contexts.
Order can also refer to a sense of control, as when someone is in a position of authority or power. In this way, order is often seen as a form of discipline or regulation that allows for things to be done in a structured, efficient, and predictable fashion.
To learn more about order
https://brainly.com/question/17169621
#SPJ4
briefly describe the simplest continuous cooling heat treatment procedure that would be used in converting a 4340 ste
We must succinctly describe the simplest continuous cooling heat treatment procedure that would be used to alter the microstructure of a 4340 steel in order to overcome this problem. The solution to this problem requires the use of Figure 10.28.
(a) It requires heating to approximately 720°C, allowing for complete austenitization, and then cooling to room temperature at a pace slower than 0.006°C/s in order to go from (martensite + bainite) to (ferrite + pearlite).
(b) The alloy needs to be heated to about 700°C for several hours in order to change from (martensite + bainite) to spheroidite.
(c) To change from (martensite + bainite) to (martensite + bainite + ferrite), it is necessary to heat the material to a temperature over 720°C, let the austenitization process finish, and then cool the material to room temperature between 0.3°C/s and 0.02°C/s.
Heat treatment is a group of thermal, industrial, and metallurgical processes used to modify the physical, and sporadically the chemical, properties of a material. The most common application is in metallurgy. Heat treatments are used to create a variety of different materials, including glass. To harden or soften materials in order to achieve the desired result, heat treatment involves heating or cooling them—typically to very high temperatures. Heat treatment techniques include quenching, annealing, case hardening, precipitation strengthening, tempering, and carburizing. Although the term "heat treatment" only refers to processes where heating and cooling are carried out specifically to change a material's properties, heating and cooling frequently happen by accident during other production processes like hot shaping or welding. Heat treatment is a group of thermal, industrial, and metallurgical processes used to modify the physical, and sporadically the chemical, properties of a material. The most common application is in metallurgy. Heat treatments are used to create a variety of different materials, including glass. To harden or soften materials in order to achieve the desired result, heat treatment involves heating or cooling them—typically to very high temperatures. Heat treatment techniques include quenching, annealing, case hardening, precipitation strengthening, tempering, and carburizing. Although the term "heat treatment" only refers to processes where heating and cooling are carried out specifically to change a material's properties, heating and cooling frequently happen by accident during other production processes like hot shaping or welding.
Learn more about heat treatment here
https://brainly.com/question/16256013
#SPJ4
Mark all of the method calls below that are calling static methods: O String str2 = inScanner.nextLine(): O String str2 = str.substring(0,3); O String str2 = String.valueOf(12); O int z = Math.max(x, y):
A static method (or static function) is a method that is declared as a member of an object but can only be accessed from the constructor of an API object, not from an instance of the object generated using the constructor.
Rather of being an instance of a class, a static method in Java is a method that is a part of the class itself. The method is available to each instance of the class. Without requiring the class's object, static methods have access to class variables (static variables) (instance). A static method can only access static data. A static method in Java is a method that is part of the class, not an instance of the class. Instead of using a class object, static methods are called by the class name. There should be a common piece of code shared by all instance methods (although you could still have an instance method for that).
To learn more about static method click the link below:
brainly.com/question/13098297
#SPJ4
A ball is thrown upward with an initial velocity of 20m/s
.a) How long is the ball in the air?
b) What is the greatest height reached by the ball?
c) When is the ball 15m above the ground?
Ball is 2.04 sec in the air after it will undergoes free fall, Max height 20.14 m and after 0.99 sec the ball 15m above the ground.
What are the equations of motion?First Equation of Motion : v = u + a t.Second Equation of Motion : s = u t + 1/2 a t ²Third Equation of Motion : v ²= u² + 2 a s.The most basic principles of an object's motion are described by kinematics equations of motion. These equations control an object's motion in 1D, 2D, and 3D. They make it simple to compute expressions like an object's position, velocity, or acceleration at different points in time.
At max height, V=0.
So:
v=u+at
0=20–9.8t
9.8t=20
t=2.04 secs…
Ball is 2.04 sec in the air after it will undergoes free fall.
s = ut + ½ at^2
=20* 2.04 - (9.8 * 2.04² / 2)
= 40.8 - 20.39
= 20.41 m
Max height 20.14 m
ball 15m above the ground:
v^2 = u^2 + 2 as.
= 20^2 - 2 * 9.8 * 15
= 400- 294
=106
v = [tex]\sqrt{106}[/tex] =10.3 m/s
v=u+at
10.3 = 20 -9.8 * t
t = (20 -10.3) /9.8 = 0.99 sec
at 0.99 sec the ball 15m above the ground.
To learn more about acceleration refer,
https://brainly.com/question/27821888
#SPJ4
will indicate if there is a problem with the differential case or the ring gear itself, which can be an indicator of whether or not to reuse a ring gear or replace the ring gear.
If there is a problem with the differential case or the ring gear itself, it can be an indicator of whether or not to reuse a ring gear or replace the ring gear.
What is indicator?
The indicator is a typical "auxiliary" instrument whose function is to give a human readable indication of the an instrument signal. Sometimes, process transmitters simply transmit a basic instrument message (4 to 20 mA, etc.) to the another device without having readouts for the variable they are measuring. For example, a level transmitter installed on a large tank will display the level value to the operator just at bottom of the tank utilising indicators as well as loop-powered devices. In some cases, we may need an additional local display to show the process value to a operators. Without needing to connect test equipment, an indicator provides a human operator with a convenient way to see what the transmitter's output is.
If the case is damaged, such as if it has been bent or cracked, it should be replaced. If the ring gear is damaged, such as if it has been chipped or scored, it should also be replaced. If the ring gear is worn but not visibly damaged, it may be possible to reuse it as long as it is inspected and properly re-torqued.
To learn more about indicator
https://brainly.com/question/29664056
#SPJ4
If a column is defined as NUMBER(5,2), which of the following is true?
The column can store a total of 7 digits, with 5 on the left side of the decimal point, and 2 on the right.
The column can store a total of 7 digits, all of them on the right side of the decimal point.
The column can store a total of 5 digits, with 3 on the left side of the decimal point, and 2 on the right.
The column can store a total of 5 digits, all of them on the left side of the decimal point.
The column is defined as NUMBER (5,2), which indicates that it can store a maximum of 5 digits to the left of the decimal point and 2 digits to the right of the decimal point.
Understanding the NUMBER(5,2) Data TypeThe column is defined as NUMBER (5,2), which means that it can store a maximum of 5 digits to the left of the decimal point and 2 digits to the right of the decimal point. This adds up to a total of 7 digits that can be stored in the column, with 5 on the left side of the decimal point, and 2 on the right.
A column defined as NUMBER (5,2) is a numeric data type used for storing numeric values. It is capable of storing a maximum of 5 digits to the left of the decimal point and 2 digits to the right of the decimal point. This adds up to a total of 7 digits that can be stored in the column, with 5 on the left side of the decimal point, and 2 on the right. This data type is useful for storing numerical values such as measurements, prices, and other data that require precision.
Learn more about Data: https://brainly.com/question/27358262
#SPJ4
Based on the following configuration, what would be the assigned global unicast address ?
interface fastEthernet 0/0
mac-address 0200.8395.2614
ipv6 address 2500:A4B3:ED81:ACEB::/64 eui-64
A. 2500:A4B3:ED81:ACEB: 200:83FF:FF95:2614
B. 2500:A4B3:ED81:ACEB: 0:83FF:FE95:2614
C. 2500:A4B3:ED81:ACEB: 200:83FF:FE95:2614
D. 2500:A4B3:ED81:ACEB: 0:83FF:FF95:2614
The correct answer is A. 2500:A4B3:ED81:ACEB: 200:83FF:FF95:2614 would be the assigned global unicast address .
Launch the command prompt. Open the Start menu in Windows 10 and type "cmd" into the search bar. Ipconfig /all. Type this command and hit Enter. To view the MAC address of the network device, choose Physical Address. While Link-local IPv6 Address displays the IPv6 address, IPv4 Address is presented next to it. An IPv6 device will create a distinct 64-bit interface ID using the MAC address of its interface. The interface ID is 64 bits while a MAC address is 48 bits. The Internet's global unicast address is exclusive worldwide. A global unicast address is what the example IPv6 address from Prefixes in IPv6 looks like.
To learn more about unicast address click the link below:
brainly.com/question/14969669
#SPJ4
an allocator using the best fit algorithm may have external fragmentation, but will have no internal fragmentation. True or False
This is a true statement because an allocator that uses the best-fit algorithm may have external fragmentation but does not have internal fragmentation.
The best-fit algorithm deals with allocating the smallest free partition that meets the criteria of the requesting process. The best-fit algorithm first searches the whole list of free partitions and considers the smallest hole that is adequate. It then attempts to identify a hole that is close to the actual process size required.
Using the best-fit algorithm provides the solution to internal fragmentation. Whereas this algorithm does not provide the solution to external fragmentation; compaction, segmentation, and paging are the required solutions to external fragmentation.
You can learn more about best-fit algorithm at
https://brainly.com/question/12996790
#SPJ4
A ___________ is mounted on an apparatus and uses a centrifugal pump to supply the water for the foam solution and an onboard air compressor to add air to the mixture before discharge
compressed air foam system (CAFS)
A compressed air foam system (CAFS) is mounted on an apparatus and uses a centrifugal pump to supply the water for the foam solution and an onboard air compressor to add air to the mixture before discharge.
A Compressed Air Foam System employs water, compressor air, and Class A foam concentrate to create a fire extinguishing agent that is more effective than the sum of its components.
Less water is lost during operations for exposure protection because compressed-air foam adheres better to vertical fire exposures. If exposure-protection treatments are required in rural regions with limited water supply, more water is still available for aggressive fire fighting.
Know more about compressor here:
https://brainly.com/question/9131351
#SPJ4
draw the shear diagram for the beam. set m0 = 500 n⋅m, l = 8 m.
Answer:
Missing information
Explanation:
kindly please provide full question with diagram.
Problem For fabrication of a digital logic module, the cost of fabrication at a company was estimated to be proportional with the following formula. Cost 2Pio + Pg +3G where: Pio is the number input and output pins of the module. Pg is the total number of internal pins on the gates of the system. G is the number of gates (types of gates are limited to AND, OR, NOT, NAND, NOR) Several designs have been proposed by the different design teams, and it has been decided to implement the design with the lowest cost. The logic equations may be simplified before analysis of cost and implementation. Design #1: X AC + CD + ABC + ABC + ABCD Design #2: Y (A+C+D) (A + C + D)(A + B + C)(A + B + C+ D) Design #3:Z = BD . CD-ABC T
ask A Propose a method or experiment to rank the cost of the designs from least to greatest cost; write description of method in paragraph form. Task B Implement your proposed method. Find the cost value for each of the desig diagrams that were used during this process. ns. Show your work. Include any Task C Analyze your cost data and arrange in a table or graph that displays the cost values from least to greatest. Task D Decide which design should be recommended for fabrication explaining why that design was selected for recommendation.
fabrication to fabricate or create anything untrue with the intent to deceive: He made up an explanation because he was late to stay out of trouble. He alleges that false evidence was used against him by the police. notably the US.
Construction of goods utilizing a combination of generally standardized elements and one or more distinct procedures is known as fabrication. For instance, steel fabrication involves creating metal structures using a variety of techniques, including cutting, bending, and assembling. The following are some instances of fabrication or falsification: producing data artificially when it should be coming from a real experiment Unauthorized tampering with or fabrication of information, texts, pictures, audio, video, music, or other works. Welders weld two pieces of metal together or patch gaps in metal by heating the metal and creating a bond. Usually, when the metal cools, the link solidifies entirely.
To learn more about fabrication click the link below:
brainly.com/question/28920453
#SPJ4