compared to the velocity of a 400 hz sound, the velocity of a 200 hz sound through air is

Answer: Fn = 630 N

Explanation:

ΣFy = Fn - mg = ma (The sum of the forces in the y-direction must equal mass * acceleration in the y direction)

Fn = mg + ma

Fn = m(g + a)

Fn = (57 kg)(9.8 m/s^2 + 1.25 m/s^2)

Fn = 630 N

The new velocity of the 0.18 kg ball, given that it's initial velocity was 0.39 m/s is 0.37 m/s

The following data were obtained from the question:

The new velocity of the first ball (0.18 Kg) can be obtained as follow:

Momentum before = Momentum after

m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂

m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂

(0.18 × 0.39) + (0.016 × 0.05) = (0.18 × v₁) + (0.016 × 0.26)

0.0702 + 0.0008 = 0.18v₁ + 0.00416

Collect like terms

0.18v₁ = 0.0702 + 0.0008 - 0.00416

0.18v₁ = 0.06684

Divide both sides by 0.18

v₁ = 0.06684 / 0.18

v₁ = 0.37 m/s

Thus, the new velocity of the 0.18 Kg ball is 0.37 m/s

Learn more about velocity after collison:

https://brainly.com/question/28151651

#SPJ1

Lisa can now pick up other paper clips with her freshly magnetized clip after exposing an iron paper clip to a very powerful magnet, which aligns the magnetic domains within the clip.

When a small portion of the iron filings comes into contact with the poles, which are the ends of the magnet, all of the filings are drawn to them. An opposite pole and a similar pole make up a magnet's two poles. While similar poles repel, opposite poles attract. The magnetic force between two magnets increases as the distance between them decreases.

There are three different types of magnets, Permanent magnet, Temporary magnet ,Electromagnets.

When ferromagnetic substances like iron and nickel are exposed to a magnetic field, magnets are produced. When heated to a certain temperature, metals acquire permanent magnetic properties.

To know more about magnetized

https://brainly.com/question/19741986

#SPJ4

The process of distillation involves selectively boiling and condensing to separate the volatile components of a liquid mixture.

Since the bulb of the thermometer is in contact with both the vapour and liquid that are entering the condenser, a higher temperature will be recorded if it is situated below the opening to the condenser than if it is put close to the aperture.

To know more about distillation

https://brainly.com/question/15080822

#SPJ4

Mechanical waves come in two different varieties: longitudinal waves, in which the medium is moved in the same direction as the wave.

The motion of the wave and the particles is always parallel in longitudinal waves. A classic illustration of a longitudinal wave is a sound wave that is moving through air.

Particles are displaced perpendicular to the wave's direction in a transverse wave. Transverse waves, such as those that cause ripples on the water's surface and vibrations in a string, are examples.

To know more about Mechanical wave visit:-

https://brainly.com/question/24459019

#SPJ4

The different component of the momentum of the ball is as bellow,

As per the details share in the above question are s bellow,

The mass of the super ball m is =50gm

The super ball drop from the height of = 1.5 m

Consider the ball's speed be v right before it hits the table.

Decrease of Potential Energy = Increase of Kinetic Energy

=> m x 9.8 x 1.5 = [tex]0.5 m v^{2}[/tex]

=> Therefore velocity = 5.42 m/s (- y direction)

A) Prior to a collision, the momentum component Y = mv

= - 0.05 x 5.42 = - 0.271 kg m/s

Consider the ball's speed be u right before it hits the table.

Increase of PE = Decrease of KE

=> m x 9.8 x 1 = [tex]0.5 m u^{2}[/tex]

=> u = 4.427 m/s (+ y direction)

B) Following the impact, the ball's Y contribution of momentum = mu

= 0.05 x 4.427 = 0.221 kg m/s

C) Now when Impulse imparted,

Consider Jy = change in momentum

= 0.221 - (-0.271) = 0.492 kg m/s

D) The ball time of contact is = 15 ms

Force = change inimpulse / time

= 0.492/0.015 = 32.82 N

E) change in Kinetic energy during collision

= KE after - KE before

[tex]= 0.5 \times 0.05 \times 4.427^{2} - 0.5\times0.05\times5.42^{2}[/tex]

= - 0.24445 J

For more such question on kinetic energy.

https://brainly.com/question/25959744

#SPJ4

Note: The correct correct question would be as bellow,

As shown in the figure (Figure 1) , a superball with mass m equal to 50 grams is dropped from a height of hi=1.5m . It collides with a table, then bounces up to a height of hf=1.0m . The duration of the collision (the time during which the superball is in contact with the table) is tc=15ms . In this problem, take the positive y direction to be upward, and use g=9.8m/s2 for the magnitude of the acceleration due to gravity. Neglect air resistance.

A) Find the y component of the momentum Pbefore,y of the ball immediately before the collision (in kg x m/s)

B) Find the y component of the momentum of the ball immediately after the collision, that is, just as it is leaving the table (in kg x m/s)

C) Find Jy, the component of the impulse imparted to the ball during collision (in kg x m/s)

D) Find the y component of the time-averaged force Favg,y in Newtons, that the table exerts on the ball

E)Find Kafter - Kbefore, the change in the kinetic energy of the ball during the collision, in Joules.

The box will be in rest due to net force applied on it is zero.

The definition of force in physics is: The push or pull on a massed object changes its velocity.

An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude.

Given that Bert and Ernie are pushing on opposite sides of the box with force of same magnitude, let it be F.

So, net force acting om the force = F-F = 0.

As that net force acting on the box is zero, the box will be in rest.

Learn more about force here:

https://brainly.com/question/13191643

#SPJ1

The gravitational force acting on the balls is different, so they won't necessarily move the same distance.

Everything falls at the same rate due to gravity. This explains why balls of different weights strike the ground simultaneously. The force acting downward is gravity, whereas the force acting upward is air resistance. The pull that is designated as tension is in that direction. As a result, the tension will point toward the string or rope and away from the mass. When a mass is hanging, the string pulls it upward, applying an upper force, which causes the tension to be on the upper side.

Learn more about force here-

https://brainly.com/question/13191643

#SPJ4

Answer: They change the shape of the lens

Explanation: It enables the lens to change its shape to focus on objects at various distances

The Fad,x, the x-component of the force exerted by the infinite wire on segment AD of the loop is 2.39 X 10⁻⁸ N. The Fbc,x, the x-component of the force exerted by the infinite wire on segment BC of the loop is 9.56 X 10⁻⁹ N. The Fnet,y, the y-component of the net force exerted by the infinite wire on the loop is zero.

1. The Fad,x, the x-component of the force exerted by the infinite wire on segment AD of the loop =

= Fad,x = u₀i₁i₂H / (2πL)

= Fad, x = [ (4π X 10⁻⁷)(0.672)(0.256) X (0.25) ] /2π X 0.36

= Fad,x= 2.39 X 10⁻⁸ N

2. The Fbc,x, the x-component of the force exerted by the infinite wire on segment BC of the loop =

= Fbc,x = u₀i₁i₂H / (2π) X (L+W)

= Fbc,x = (4π X 10⁻⁷)(0.672)(0.256)((0.25)/2π X (0.36+0.54)

= Fbc,x = 9.56 X 10⁻⁹ N

3. The Fnet,y, the y-component of the net force exerted by the infinite wire on the loop =

= Fnet,y = 0, since force acting on perpendicular wire is zero.

To know more about Force exerted on a loop:

https://brainly.com/question/15887276

#SPJ4

The electric field inside the dome of a highly-charged van de graaff generator is ZERO.

Van de Graaff generators are electrostatic generators and partial accelerators that store direct current on a hollow sphere by creating a strong electric field. With a potential difference of up to 5 megavolts, it is a partial accelerator.

know more about electric field here

https://brainly.com/question/15800304#

#SPJ4

The acceleration of the light truck travelling around a flat curve with a radius of 140 m and a speed of 26 m/s is 17.14 m/s².

The acceleration of a light truck travelling around a flat curve with a radius of 140 m and a speed of 26 m/s can be calculated by using the equation: acceleration = (v2/r).

In this equation, ‘v’ is the speed of the truck, and ‘r’ is the radius of the curve.

Therefore, when substituting these values into the equation, we get: acceleration

= (262/140)

= 17.14 m/s².

This means that the acceleration of the light truck travelling around a flat curve with a radius of 140 m and a speed of 26 m/s is 17.14 m/s².

Learn more about acceleration at :https://brainly.com/question/980919

#SPJ4

g a block is pulled at a constant speed along a rough level surface by a rope the magnitude of the normal force could be reduced by greater than zero but less than W.

A force is an effect that can alter an object's motion according to physics. A force can cause an object with mass to accelerate when it changes its velocity, for as when it moves away from rest. An obvious way to describe force is as a push or a pull. A force is a vector quantity since it has both magnitude and direction. It is calculated using the newton SI unit (N). Force is denoted by the letter F. (formerly P). The net force acting on an object is equal to the rate at which its momentum varies over time, according to Newton's second law in its original formulation. Thrust, which increases an object's velocity; drag, which decreases an object's velocity; and torque, which causes changes in an object's rotational speed, are all concepts connected to force. Each part of an extended body often exerts stresses on the sections that are nearby; the distribution of these forces throughout the body is what is known as the internal mechanical stress.

To know more about force please refer: https://brainly.com/question/13191643

#SPJ4

Risks. Sunburn is a sign of short-term overexposure, while premature aging and skin cancer are side effects of prolonged UV exposure.

Risks. Premature ageing and skin cancer are side consequences of continuous UV exposure, whereas sunburn is a symptom of short-term overexposure. If eye protection is not used, UV exposure raises the risk of potentially blinding eye illnesses. UV radiation overexposure can cause major health problems, including cancer.

The amount of UV radiation is unrelated to the temperature. The position of the sun in the sky is mostly to blame for variations in UV levels between summer and winter. UV radiation is often impacted by changes in the stratospheric ozone and global climate change. More UVB (the higher-frequency, more dangerous kind of UV) may now reach the Earth's surface due to a decrease in stratospheric ozone.

To learn more about UV radiation visit:https://brainly.com/question/13849635

#SPJ4

The de Broglie wavelength and speed of an electron accelerated is  0.1896nm.

1/2 m[tex]v^{2}[/tex] = K.E = ev

Charge on electron = 1.6 × [tex]10^{-19}[/tex]coulombs

Mass  of electron = 9.1 × [tex]10^{-31}[/tex]Kg

1/2 × 9.1 × [tex]10^{-31}[/tex] × [tex]v^{2}[/tex] = 1.6 × [tex]10^{-19}[/tex]  × 250

[tex]v^{2}[/tex] = [tex]\sqrt{0.02552}[/tex]

v = 2.125 × [tex]10^{6}[/tex]

λ = h/mv = 0.1896nm.

A subatomic particle having a negative one elementary electric charge is known as an electron (e or ). Due to their lack of known components or substructure, electrons, which are part of the lepton particle family's first generation, are typically considered to be elementary particles. [1] The mass of an electron is roughly equivalent to that of a proton (1/1836). [15] The electron's inherent angular momentum (spin), which is measured in terms of the scaled-down Planck constant,, is one of its quantum mechanical properties. The Pauli exclusion principle states that because electrons are fermions, no two of them may be in the same quantum state. [14] Like all elementary particles, electrons possess characteristics of both waves and particles. They can collide with other particles and undergo light-like diffractive bending. The electron wave characteristics are simpler.

Learn more about electron here:

https://brainly.com/question/13130380?

#SPJ4

Answer:

Redshift, Blueshift, Doppler Effect, or Doppler Shift

Explanation:

When a star is moving towards us, the light waves get compacted and the light appears blue, this is known as blueshift.

When a star is moving away from us, the light waves get spread apart and the light appears red, this is known as redshift.

Both of these are called the doppler effect or doppler shift.

I'm not sure which answer you need but I hope this helps!

No; the rope doesn't change the moment arm so the torque you exert won't increase.

In physics, a force is a power that can change the motion of an item. A force could purpose an object with mass to alternate its pace. Pressure also can be described intuitively as a push or a pull. A force has both value and path, making it a vector quantity.

A pressure is either a push or a pull and it affects our each day lives because without force, people might not be capable of open and near stuff or lift up our arms or legs .

Learn more about Force here:- https://brainly.com/question/12970081

#SPJ4

A waterskier skis over the ramp shown in the figure at a speed of 30 ft/s, 7.73 ft/sec is rising as she leaves the ramp.

We assume the hypotenues = h

From the given figure (attached) ;

h² = x² + y²

Put the  values of x and y from the figure

h² = 15² + 4²

h² = 225 + 16

h² = 241

Take under root on both sides

h = √241

From the figure the value of sin∅ = 4/h

Put value of h

sin∅ = 4 / √241

The rate at which she is rising = verticle velocity

The rate at which she is rising = 30sin∅

Put the value of sign∅

The rate at which she is rising = (30 * 4) / √241

The rate at which she is rising = 7.73 ft/sec

The missing figure is attached.

You can also learn about verticle velocity from the following question:

https://brainly.com/question/29553099

#SPJ4

The far that can it glide in terms of distance measured along the ground is 38,500 ft.

Given that,

World War I Sopwith Camel was 7.7.

If the aircraft is in flight at 5000 ft when the engine fails.

Based on the above information, the calculation is as follows:

[tex]\begin{aligned}& \frac{\text { lift }}{d r a g}=\frac{\text { Distance }}{\text { height }} \\& 7.7=\text { Distance } \div 5500\end{aligned}[/tex]

So, the distance is 38,500 ft.

Distance is a measurement of how far away two things or locations are, either numerically or occasionally qualitatively. Distance can refer to a physical length in physics or to an estimate based on other factors in common use.

To learn more about Distance  visit:https://brainly.com/question/15172156

#SPJ4

The hypothesis is that, a changing electric field gives rise to a magnetic field.

What is electromagnetism?

The electromagnetic force that exists between electrically charged particles is the subject of the branch of physics known as electromagnetism. One of the four fundamental forces is the electromagnetic force.

 What is electric field?

The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them, is known as an electric field (or E-field).

What is magnetic field?

The magnetic influence on moving electric charges, electric currents, and magnetic materials is described by a magnetic field, which is a vector field.

To learn more about electromagnetism:

https://brainly.com/question/17057080

#SPJ4

The power, the resistor and time is I²₀R e-2Rt/L and - I₀²R  e-2Rt/L .

Work rate or energy delivery time is expressed as W/t, where W is the quantity of work completed or energy delivered, and t is the time interval.

A passive electrical device with two terminals that controls or limits the flow of electricity across electrical circuits. The main function of a resistor is to lower the voltage and reduce the current flow in a specific area of the circuit.

a) L di/dt + iR = 0 -Rt/L

= I = I₀ e

At t=0.  I = I₀

= Pr = I²R = I₀ R e = -2Rt/t

= Pr (t) = I²₀R e-2Rt/L

b) Energy of inductor = 1/2 L I²

= 1/2 L I₀²    e-2Rt/L

Power, Pl (t) = dE/dt

= d/dt (1/2 LI₀² e-2Rt/L)

= 1/2 t I₀² ( e-2Rt/L) e-2Rt/L

Pl (t) = - I₀²R  e-2Rt/L

Therefore, the power, the resistor and time is I²₀R e-2Rt/L and - I₀²R  e-2Rt/L .

To know more about Power:

https://brainly.com/question/29896579

#SPJ4

Assuming Jocko the clown (mass of 60kg) catches the 7kg bowling ball, which thrown into his direction at 10m/s, the energy that will lost in the collision is 313J (based on Conservation of momentum).

Conservation of momentum is a major law of physics which states that the momentum of a system is constant if no external forces are acting on the system.

Based from the question given :
m₁ (mass of jocko) = 60kg

v₁ (initial speed of jocko) = 0 m/s

m₂ (mass of bowling ball) = 7kg

v₂ (initial speed of bowling ball) = 10 m/s

Now let's use the conservation of momentum formula

m₁ * v₁ + m₂ * v₂ = (m₁ + m₂) * V

60 * 0 + 7 * 10 = (60 + 7) * V

V = 70 / 67 m/s

Energy lost = Kinetic energy initial (bowling ball) - Kinetic energy final

= 1/2 * m₂ * v₂² - 1/2 (m₁ + m₂) * V²

= 1/2 * ((7 * 10²) - (67 * (70/67)²))

= 1/2 * 626.86

= 313.43J

=313J (rounded)

Therefore, energy that lost in the collision is 313J.

Learn more about conservation of momentum https://brainly.com/question/24989124

#SPJ4

The square of the separation distance is inversely correlated with the electrostatic force. F is therefore nine times smaller, or one-ninth the original value, if d is three times larger.

Coulomb's Law states that the force exerted between two charged objects is inversely related to their square of distance. As a result, if the distance is tripled, the force will be nine times weaker. The force between two charges is inversely proportional to the square of the distance between them and directly proportional to the product of the charges. The force between the two charges will therefore treble if the charge on q1 is tripled while the other charge and distance remain constant.

Learn more about force here-

https://brainly.com/question/13191643

#SPJ4

The magnitude of the electric field is 17.80

We are given that,

e = (-11i^+14j^)n/c

x component = -11

y component = 14

To calculate the magnitude of the electric field we can use formula ,

e = √x² + y²

e = √-11² + 14²

e = √121 + 196

e = √317

e = 17.80

Therefore , the magnitude of the electric field would be 17.80.

To know more about

https://brainly.com/question/13747123

#SPJ4

The speed changes as a result of the energy being transferred into a container filled with magnetic marbles and the kinetic energy produced by the container's gentle shaking. Phase shifts will result from this.

The energy of a system changes together with each phase change it undergoes. These involve kinetic energy transmission to a system. Endothermic reactions occur when a condition changes from being more ordered to being less ordered. Exothermic reactions are always involved in transitions from one state to another that is more organised.

When a substance transforms from one state to another, a phase change occurs in the system. When the system receives enough energy or loses enough energy, these changes take place. Phase changes also happen when the system's pressure is altered.

To learn more about Kinetic energy here:

https://brainly.com/question/999862#

#SPJ4

Complete Question:

Describe how does transferring energy into a container of magnetic marbles affect the speed by shaking the container gently?

The correct option is B) [tex]d_{low} = 4d_{high}[/tex].The diameter of the lowest string is four times that of the highest string.

Because frequency is inversely proportional to the square root of mass density, the low string's mass density would be 16 times greater. The radius would increase by 4 times as a result.

If the diameter is same, the mass is same and the speed is 1/4 times due to the square root sign in the denominator. The frequency is 1/4 times because the wavelength is constant.

The relationship between frequency and diameter of a string is given by,

[tex]f=\frac{1}{L*d} \sqrt{\frac{4T}{\rho \pi}}[/tex]

Where,

L = length of the string

d= diameter of the string

T= tension of the string

[tex]\rho[/tex] = density of the string

Given, that the lengths of the strings are same; tension of the strings are same and as the string are of same material then the density of the strings are also same.

Thus, the frequency is inversely proportional to the string diameter.

f  = 1/d

So, if

[tex]4f_{low} = f_{high}[/tex]

Then,

[tex]d_{low} = 4d_{high}[/tex]

Thus,the diameter of lowest string is 4 times the diameter of highest string.

To learn more about frequency of string refer here

https://brainly.com/question/13552044

#SPJ4

Your question is incomplete, here is the complete question

The 6 strings on a guitar all have about the same length and are stretched with about the same tension.The highest string vibrates with a frequency that is 4 times that of the lowest string.

If the strings are made of the same material, how would you expect the diameters of the lowest and highest strings to compare?

[tex]A.\ d_{low}=2d_{high}\\\\B.\ d_{low}=4d_{high}\\\\C.\ d_{low}=16d_{high}[/tex]

Yes, the magnitude of the acceleration due to gravity near Earth surface increases more if Earth's mass were doubled.

The magnitude of the acceleration due to gravity on the surface of the Earth is given by the relation,

g = GM/r²

Where,

G is the universal gravitational constant,

M the mass of the earth and,

R is the radius of the earth.

Now if the radius of the earth is kept constant and mass of the earth is doubled.

The value of the new acceleration due to gravity will become,

g' = G2M/r²

Putting GM/r² = g,

g' = 2g

So, we can see that the new acceleration due to gravity because of the increase in the mass of the earth is two times of the earlier acceleration due to gravity.

To know more about acceleration due to gravity, visit,

https://brainly.com/question/88039

#SPJ4

The empirical formula is CHO.

Maleic acid generates 1.599g of CO2 and 0.327g of H2O from a sample of 1.054 g.

So, use molar masses to calculate mass.

1.599 grams of [tex]CO_2[/tex] at (12.01 grams of carbon)/(44.01 grams of carbon) = 0.436 grams of carbon

0.037 grams of hydrogen are equal to 0.327g of H2O at (2.016 g Hydrogen) / (18.01 g/mol H2O).

1.054 g sample divided by 0.436 g of carbon and 0.037 g of hydrogen yields 0.581 g of oxygen.

Now locate moles by using molar masses.

0.436 grams of carbon with a molecular weight of 12.01 = 0.0363 mol C

0.0367 mol H for 0.037 grams of hydrogen and 0.0363 mol O for 0.581 grams of oxygen

For more questions on Empirical formula

https://brainly.com/question/26388921

#SPJ4

The complete question should be:

In combustion analysis, a 1.054-g sample of maleic acid yields 1.599g of CO29 and 0.327g of H20.

When 0.609g of maleic acid dissolved in 25.00g of glacial acetic acid, the freezing point drops by 0.82 degrees C Maleic acid does not ionize in glacial acidic acid, which has a freezing point depression constant of Kf=3.90*c/m.

In a titration experiment, a 0.4250-g sample of maleic acid is dissolved in water and requires 34.03ml of 0.2152 M KOH for its complete neutralization.

The pH of 0.215g of maleic acid in 50.00mL of the aqueous solution is found to be 1.80.

Determine the empirical formula for maleic acid. Enter the atoms in order of C, H, and O.

The fraction of the neutron's kinetic energy transferred to the atomic nucleus is 2.05

If the initial kinetic energy of the neutron is

4.2 × 10−13 J, its final kinetic energy  will be 2.50 joules

kinetic energy of an object is described as the energy that it possesses due to its motion which is also the work needed to accelerate a body of a given mass from rest to its stated velocity.

In elastic head-on collision, the energy of the system and total momentum is conserved.

For the neutron,

m - mass

Vi - initial velocity

Vf - final velocity

For the atom ,

M- mass

Mi - initial velocity

Mf - final velocity

Conserved momentum on the head-on collision

mvi = mvf + MVF

vi - vf = MmVf

Vi- vf = 11.1 vf...... (i)

The kinetic energy is

Vi²- vf² = 11.1 v²f.......(ii)

Combining both equations

Vi + Vf = Vf

Solve equation (I) and (III) for Vi

vi = 5.4vf

Now, the fraction of the neutron's kinetic energy transferred to the atomic nucleus,

1/2 mv²f/ 1/2 mv²i = 11.1/ 5.4

If the initial kinetic energy of the neutron is

4.2 × 10−13 J, its final kinetic energy  will be 2.50 joules

Hence, we can conclude that the fraction of the neutron's kinetic energy transferred to the atomic nucleus is 2.05

Learn more about kinetic energy at: https://brainly.com/question/20658056

#SPJ1

If the surface temperature of the sun were to drop by a factor of 2.0, the power impinging on the earth would decrease by a factor of 8 times.

The quantity of energy transferred or transformed per unit of time is known as power. It is a mechanically accepted quantity. The watt, or one joule per second, is the unit of power in the International System of Units. Power is also referred to as activity in ancient writings. A scalar quantity is power. Power is related to other factors; for instance, the power required to move a ground vehicle is equal to the product of the vehicle's velocity, traction force on its wheels, and aerodynamic drag. A motor's output power is calculated by multiplying its torque output by the angular velocity of its output shaft. Energy divided by time represents the dimension of power. The watt (W), which equates to one joule per second, is the unit of power in the International System of Units (SI). Another popular unit of measurement is horsepower (hp), which is equivalent to a horse's power; one mechanical horsepower is equal to around 745.7 watts. Ergs per second (erg/s), foot-pounds per minute (fpm), dBm (a logarithmic measurement in relation to 1 milliwatt), calories per hour (cal/h), BTU per hour (BTU/h), and tons of refrigeration are other units of power.

To know more about power please refer: https://brainly.com/question/14450944

#SPJ4