Chevrolet Corvette Sting Ray developed 360 horsepower and hada displacement of 327 cubic inches. Express this displacement inliters (L) by using only the conversions 1 L = 1000 cm3 and1 in. = 2.54 cm.

Answers

Answer 1

The displacement in litres is 5.36 L.

Conversion of units is the conversion between different units of measurement for the same quantity, typically through multiplicative conversion factors which change the measured quantity value without changing its effects.

Horsepower = 360

Displacement  327 inches³

1 L = 1000 cm³

1 inch = 2.54 cm

Displacement in litres is =

First find displacement in cubic centimetre =

= d = 327 inch³ X (2.54 cm / 1m)³

= d = 327 X 2.54

= d = 5358.57 cm³

We know that, 1 L = 1000 cm³,

Thus,

The displacement in Litres is =

= d =  5358.57 cm³ X (1L / 1000 cm³)

= d = 5.36 L

To know more about Conversion of Units:

https://brainly.com/question/14661466

#SPJ4


Related Questions

what is the maximum speed of a 2.0 g particle that oscillates between x =2.0 mm and x =8.0 mm in

Answers

The period of motion is simple hormonic motion and the maximum speed of the particle is 0.0031s

(a) Simple harmonic motion is defined as "the motion of a mass on a spring when it is subject to the linear elastic restoring force given by Hooke's Law (F=-Kx). The motion experimented by the particle is sinusoidal in time and demonstrates a single resonant frequency".

(b) The equation that describes the simple harmonic motion is given by =

= X = Acos(ωt + θ)     [1]

And taking the first and second derivate of the equation (1) we obtain the velocity and acceleration function respectively.

For the velocity:

= V = dx/dt = -Aωsin(ωt + θ)        [2]

For the acceleration:

= A = dv/dt =  -Aω²cos(ωt + θ)           [3]

As we can see in equation [3] the acceleration would be maximum when the cosine term would be -1 and on this case:

= Aω² = 8x10³ m/s²

Since we know the amplitude A=0.002m  we can solve for ω like this:

= ω = √ (8000/0.002)

= ω = 2000 rad

And we with this value we can find the period with the following formula;

= T = 2π/ω = 0.0031s

To know more about Simple Hormonic Motion:

https://brainly.com/question/13994626

#SPJ4

The complete question:

A 10 g particle undergoes SHM with an amplitude of 2.0 mm and a maximum acceleration of magnitude 8.0 multiplied by 103 m/s2, and an unknown phase constant ?.(a) What is the period of the motion?1 s(b) What is the maximum speed of the particle?

what type of solar heating system would be most efficient at producing high-temperature water for industrial applications or steam to run turbines that generate electricity?

Answers

Angela092505's response Solar thermal electric generation systems that use mirrors or lenses to focus sunlight to heat water are the answer.

define solar heating ?

The use of sunlight to heat water or air in buildings is known as solar heating. Solar heating is classified into two types: passive and active.

To heat buildings, passive heating relies on architectural design. The location, construction, and materials of the building may all be used to optimise the heating (and lighting) impact of the sunshine falling on it, minimising or even eliminating the need for fuel. On sunny days, a well-insulated structure with a large glass window facing south, for example, can efficiently trap heat and decrease dependency on gas or oil (for heating) or electricity (for lighting). Natural convection warms the air and solid surfaces in rooms exposed to sunlight, and this warmth is carried to other rooms in the building.

What kind of solar heating system is most efficient in producing high-temperature water for industrial uses or steam to power turbines that generate electricity Angela092505's response Solar thermal electric generation systems that use mirrors or lenses to focus sunlight to heat water are the answer.

To learn more about solar heating follow the given link:https://brainly.com/question/28399046

#SPJ1

what is the current i(t) in the circuit at time t after the switch is closed? express your answer in terms of q0 , l , c , and other variables given in the introduction.

Answers

If the current i(t) in the circuit at time t after the switch is closed  in terms of q0 , l , c the differential equation will be V(t) = (q0/C) × e^(−t/RC )

The equation for V(t) would be V(t)=E(RC)(dV(t)/dt) if a battery with EMF E was present in the circuit. With respect to V(t), this differential equation is no longer homogenous. But it can be resolved by simply substituting Vb(t)=V(t)E. This substitution has the effect of removing the E term and producing an equation for Vb(t) that is the same as the equation you solved for V(t). When a battery is supplied, the capacitor's initial condition is typically that it is completely discharged at time t=0.

In these circumstances, the solution will appear as V(t)=E(1et/(RC)) Since the voltage across the capacitor is zero at time t=0 according to this solution, is 0 at time t=0 since the capacitor wasn't charged at that point, and it climbs asymptotically to E.

To know more about differential equation

https://brainly.com/question/14959401

#SPJ4

a 25-kg crate is pushed across a frictionless horizontal floor with a force of 20 n, directed 20o below the horizontal. the acceleration of the crate is:

Answers

1.75 m/s2 is the crate's acceleration.

mass=25kg, f=20n.

In terms of physics, what is frictionless?

A surface is said to be frictionless if it has a force acting on any thing that is practically zero or insignificant, meaning that there is no resistance between the surface and the material, allowing the object to slide and move freely without any friction.

Can one walk on a frictionless surface?

Every every activity that requires the interaction of two surfaces and motion involves friction, with the exception of space walks, which you may conduct without any resistance. Because there won't be any contact force to propel the individual forward, one cannot walk in the absence of friction.

To know more about Frictionless visit:

https://brainly.com/question/26515803

#SPJ4

a block of mass 0.482 kg is hung from a vertical spring and allowed to reach equilibrium at rest. as a result, the spring is stretched by 0.630 m. find the spring constant.

Answers

The spring constant of the spring is 7.497 N/m.

The given parameters;

mass of the block, m = 0.482 kg

extension of the spring, x = 0.630 m

additional extension, = 0.338 m

The spring constant of the spring is calculated as follow

F = mg

Kx = mg

K = mg/x

K = 0.482 × 9.8 / 0.630 = 7.497N/m

F = -kx.

The spring constant, or k, is the proportional constant. It is a gauge of the spring's rigidity. A spring exerts a force F = -kx in the direction of its equilibrium position when it is stretched or compressed to a length that deviates by an amount x from its equilibrium length. The spring constant is calculated by dividing the force required to extend or compress a spring by the length it goes up or down. It is used to assess the stability or instability of a spring, The spring's stiffness is quantified by the spring constant, or k. For various springs and materials, it differs. The stiffer the spring is and the harder it is to stretch, the greater the spring constant.

Learn more about spring constant here:

https://brainly.com/question/14159361

#SPJ4

A 4.8-kg suitcase is sliding across the horizontal floor of an elevator. The coefficient of kinetic friction between the suitcase and the floor is 0.28.


a) If the elevator is moving upward at a constant speed of 1.6 m/s, find the kinetic frictional force acting on the suitcase.


b) If the elevator is accelerating upward at 1.6 m/s?, find the kinetic frictional force acting on the suitcase


c) If the elevator is accelerating downward at 1.6 m/s, find the kinetic frictional force acting on the suitcase.

Answers

Answer:

Below

Explanation:

a)  At constant speed the only force acting downward is the usual Normal Force due to gravity

Fn = mg = 4.8 * 9.81 =47.1 N

                the force of friction is then Ff =  Fn * coeff = 47.1 * .28 = 13.2 N

b)  If the acceleration is UPWARD this adds to g

      Fn then becomes

             Fn = 4.8 ( 9.81 + 1.6) = 54.8 N   and    Ff = 54.8 * .28 = 15.3 N

c)  Similar to b)  but this time the acceleration of the elevator SUBTRACTS from gravity    

    Fn = 4.8 ( 9.81 - 1.6) = 39.4 N    and    Ff = 39.4 * .28 = 11.0 N

commercial jets usually land using a 3-degree angle of descent. at what distance from the destination airport should the pilot begin the descent, if the cruising altitude of the jet is 37000 feet?

Answers

To obtain a 3 degree drop, begin your descent three times your altitude (measured in thousands of feet).

Start down at 3 x 50 = 150 miles out if you are at 45,000 feet, for ease of calculation, round the height up to 50. When an airplane is between 100 and 120 miles from its destination, it often starts to descend (assuming the cruising altitude is above 30,000 feet). Typically, people use some variation of the 3/6  to larger aircraft: The distance back to begin the fall is 3 times the height (in thousands of feet), and the descending rate is 6 times your ground speed.

Learn more about speed here-

https://brainly.com/question/28224010

#SPJ4

A monochromatic beam of light is absorbed by a collection ofground-state hydrogen atoms in such a way that six differentwavelengths are observed when the hydrogen relaxes back to theground state.
(a) What is the wavelength of the incident beam? Explain the stepsin your solution.
(b) What is the longest wavelength in the emission spectrum ofthese atoms? To what portion of the electromagnetic spectrum and towhat series does it belong?
(c) What is the shortest wavelength? To what series does itbelong?

Answer Key:
(A) The atoms must be excited to energy level n = 4, to emit sixdifferent photon
energies in the downward transitions 4→3, 4→2,4→1, 3→2, 3→1, and 2→1. The
photon energy absorbed in the 1→4 transition is 12.8 eV,making the wavelength 97.4
nm.
(B) 1.88 μm, infrared, Paschen
(C) 97.4 nm, ultraviolet, Lyman

Answers

The incident beam of light has a single, monochromatic wavelength. When this beam is absorbed by the hydrogen atoms, the atoms become excited and eventually relax back to the ground state, emitting light at several different wavelengths.

(a) It is not possible to determine the wavelength of the incident beam based on the information provided.

(b) The longest wavelength in the emission spectrum of the hydrogen atoms corresponds to the transition between the lowest energy levels in the atom. In the case of hydrogen, the ground state is the lowest energy level, so the longest wavelength would correspond to a transition from an excited state to the ground state.

(c) The portion of the electromagnetic spectrum to which the longest wavelength belongs depends on the specific value of the wavelength. The electromagnetic spectrum includes radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays.

(d) The series to which the longest wavelength belongs can be determined by the values of the energy levels involved in the transition. In the case of hydrogen, there are three series: the Lyman series, the Balmer series, and the Paschen series. The Lyman series corresponds to transitions from higher energy levels to the ground state, the Balmer series corresponds to transitions from intermediate energy levels to the ground state, and the Paschen series corresponds to transitions from lower energy levels to the ground state.

(e) The shortest wavelength in the emission spectrum corresponds to the transition between the highest energy levels in the atom. In the case of hydrogen, the shortest wavelength would correspond to a transition from an excited state to a higher energy level.

(f) The portion of the electromagnetic spectrum to which the shortest wavelength belongs depends on the specific value of the wavelength.

(g) The series to which the shortest wavelength belongs can be determined by the values of the energy levels involved in the transition. In the case of hydrogen, the shortest wavelength would belong to the Lyman series, since it corresponds to a transition from an excited state to a higher energy level

To learn more about electromagnetic spectrum visit:https://brainly.com/question/23727978

#SPJ4

find the turning-point angles if the child has a speed of 0.80 m/s when the ropes are vertical.

Answers

The turning-point angles is θ = 9.666 degrees if the child has a speed of 0.80 m/s when the ropes are vertical.

As per the details provided in the above question are as bellow,

The speed at bottom = v = 0.8 m/s

The length of the rope = l = 2.3 meter

The Work Energy Theorem provides us with,

The energy an item has as a result of motion is known as kinetic energy. A force must be applied to an item in order to accelerate it. We must put forth effort in order to apply a force. After the job is finished, energy is transferred to the item, which then moves at a new, constant speed.

Change in kinetic energy = net work done

[tex]0 - 0.5mv^2 =[/tex]- mgl (1-cosθ)

[tex]0.5 \times 0.8^2[/tex] = 9.8 x 2.3 (1-cosθ)

angle θ = 9.666 degrees

For more such question on angles.

https://brainly.com/question/25770607

#SPJ4

Note:- The correct question would be as bellow,

A child swings back and forth on a swing suspended by 2.3m -long ropes.

Find the turning-point angles if the child has a speed of 0.80 m/s when the ropes are vertical.

the electric potential in a region of space is v=200v⋅mx2+y2√, where x and y are in meters.

Answers

Electric field strength at (2.1m,3.0m) = 14.914 V/m

So in order to find electric field strength at a point whose cordinate is (x,y) is given by the term E(x,y)

Given:

V=200 (V⋅m) /√(x2+y2),  

E = ∂V/∂x i + ∂V/∂y j

where i is vector along x axis whose magnitude is 1 and hence it is unit vector and j is vector along y axis whose magnitude is 1 and hence it is unit vector.

∂V/∂x  =  [tex]\frac{-200x}{(x^2+y^2)^3^/^2}[/tex]

=>  (-200*2.1)/49.11

=>   8.55

∂V/∂x  =  [tex]\frac{-200y}{(x^2+y^2)^3^/^2}[/tex]

=> (-200*3)/49.11

=> 12.22

so E(2.1,3) = -8.55 i -12.22 j

  so E = [tex]\sqrt{-8.55*-8.55 + -12.22*-12.22}[/tex]

=> [tex]\sqrt{222.43}[/tex]

=> 14.914 V/m

so the magnitude of Electric field at (2.1m,3.0m) = 14.914 V/m

To know in depth about Electric field strength click on link given below:

https://brainly.com/question/28227168#

#SPJ4

Complete question:

The electric potential in a region of space is V= 200 (V⋅m) /√(x2+y2), where x and y are in meters. Find the strength of the electric field at (x,y)=(2.1m,3.0m) ?

A rightward force is applied to a 6-kg object to move it across a rough surface at constant
velocity. The object encounters 15 N of frictional force. Use the diagram to determine the
gravitational force, normal force, net force, and applied force.

Answers

Fnorm = 58.8 N; Fnorm = 58.8 N; Fapp = 15 N; Fnet = 0 N. In the case of constant velocity, a = 0 m/s/s and Fnet = 0 N, Fgrav = m • g • 9.8 m/s/s • 6 kg • 58.8 N Ffrict = Fapp = 15 N since there is no horizontal acceleration.

A rightward force is what?

A book is moved across a desk with a rightward acceleration by applying a rightward push to it. Consider the effects of friction. Pass over air resistance. Static Friction = Normal Force x Static Friction Coefficient is the formula for calculating static friction.

How can I determine force?

Newton's second law of motion provides the definition of the force formula: An object's force is equal to its mass times its acceleration. F = m ⨉ a. To apply this formula, you must use SI units for force (newtons), mass (kilograms), and acceleration (meters per second squared).

to know more about force here:

brainly.com/question/26115859

#SPJ1

if the amplitude increases to 0.20 mm , by what factor does the bug's maximum kinetic energy change?

Answers

The bug's maximal kinetic energy changes as 16 times of Kinetic energy before amplitude increases when the amplitude approaches 0.20 mm.

The amplitude of a wave is its largest displacement. The wave's greatest velocity is now expressed as its amplitude, which is: v =Aw= K/M.

Now, the square of the wave is directly proportional to the kinetic energy of a system. As a result, the wave's maximum kinetic energy is given by KE = k/2A^2, which means that

KE1/KE2 = A1^2/A2^2 where KE1 is the kinetic energy prior to the amplitude (A1) increasing and KE2 is the kinetic energy following the amplitude increasing (A2)

Due to that,

The bug's entire vertical journey was S = 0.10m

The wave's amplitude is equal to half of the whole distance from the top to the bottom, hence its value is (A) = S/2 = 0.1/2 = 0.05m.

Now that the wave's amplitude has increased to 0.20 m, KEA = KE1/KE2 = A1^2/A2^2

KE1/KE2 = (0.05)^2/(0.20)^2, which equals 0.0025/0.04 = 0.0625.

KE2 then equals 16KE1

Therefore, the largest change in kinetic energy is (KE2) = 16KE1.

​To learn more about kinetic energy click here https://brainly.com/question/26472013

#SPJ4

Find complete question:  A bug on the surface of a pond is observed to move up and down a total vertical distance of 0.10 m, lowest to the highest point, as a wave passes. What is the amplitude of the wave? If the amplitude increases to 0.20 m, by what factor does the bug's maximum kinetic energy change?

if you placed 1.00 c of positive charge on the earth and 1 c of negative charge 384,500 km away on the moon, how much force would the positive charge on the earth experience

Answers

If you placed 1.00 coulomb (C) of positive charge on the Earth and 1 C of negative charge 384,500 km away on the Moon, the positive charge on the Earth would experience a gravitational force of attraction towards the negative charge on the Moon.

The gravitational force of attraction between two charged particles is given by the formula:

F = (k * q1 * q2) / r^2

where F is the gravitational force, k is the Coulomb constant, q1 and q2 are the charges of the two particles, and r is the distance between them.

Plugging in the values provided, we get:

F = (8.99 x 10^9 N*m^2/C^2) * (1 C) * (1 C) / (384,500 km)^2

= 2.34 x 10^-9 N.

This is a very small force due to the large distance between the two charges and the relatively small magnitude of their charges.

Learn more about The gravitational force here:

https://brainly.com/question/27943482

#SPJ4

consider the situation in the figure below, where two charged rods are placed a distance d on either side of an aluminum can. what does the can do?

Answers

The left side of the can receives a negative charge from the positively charged rod, which creates a force of attraction between both the rod and the can.

How does science define force?

In science, the term "force" has a particular definition. At this point, describing a force as pushing or pulling is quite acceptable. A force does not "exist in an object" or "contain an object." One object experiences a force from another. Living organisms and inanimate objects are both included in the concept of a force.

Why is force so crucial?

A force is either a push or a pull, and it has an impact on our everyday lives because without it, we couldn't open and close things, lift our arms and legs, or do much of anything else.

To learn more about force visit:

https://brainly.com/question/13191643

#SPJ4

A boat travels 12.0 m while it reduces its velocity from 9.5 m/s to 5.5 m/s. What is the magnitude of the boat’s acceleration while it travels the 12.0 m?
a. 1.3 m/s2
b. 2.5 m/s2
c. 3.0 m/s2
d. 7.5 m/s2

Answers

The magnitude of the boat’s acceleration while it travels 12.0 m is b. 2.5 [tex]ms^{-2}[/tex]

u= 9.5 [tex]ms^{-1}[/tex]

v= 5.5 [tex]ms^{-1}[/tex]

s= 12 m

From the given data we can use,

[tex]v^{2} -u^{2} =2as[/tex]

to calculate acceleration.

[tex]v^{2} -u^{2} =2as[/tex],

Where,

v is the final velocity,

u is the initial velocity,

a is the acceleration and

s is the distance covered.

Substituting the values we have,

[tex]v^{2} -u^{2}[/tex]= 2×a×s

[tex](5.5)^{2}[/tex] - [tex](9.5)^{2}[/tex]= 2 ×a×12

a= [tex]\frac{(5.5)^{2} -(9.5)^{2}}{(2)(12)}[/tex]

a= [tex]\frac{(30.25)^{2} -(90.25)^{2}}{(24)}[/tex]

a=[tex]\frac{-60}{2000}[/tex]

a=-2.5 [tex]ms^{-1}[/tex]

(The negative sign says that it is a negative acceleration  )

Therefore the magnitude of the boat's acceleration is -2.5 [tex]ms^{-1}[/tex]

To know more about Acceleration refer here:

https://brainly.com/question/12550364#

#SPJ4

A 3000kg helicopter, tilted as shown, is flying horizontally (neither gaining nor losing altitude). The helicopter is experiencing a 1200N drag.

How many forces are acting on the helicopter?

Are all the forces on the helicopter balanced?

What is the magnitude of the thrust?

What is the magnitude of the net force on the helicopter?

What is the magnitude of the helicopter's acceleration?

Describe the helicopter's speed. (increasing/decreasing/constant)

Answers

The number of forces acting on the helicopter is 3.

The forces on the system are not balanced

The magnitude of the thrust is 7,112,5 N.

The net force of the helicopter  is 5,912.5 N

The magnitude of the helicopter's acceleration is 1.97 m/s².

The speed of the helicopter is increasing towards to the right.

How many forces are acting on the trailer?

The number of forces acting on the helicopter is calculated as follows;

the weight of the helicopter acting downwardsthe thrust of the helicopterdrag force of the helicopter

The magnitude of the thrust is calculated as;

F = W sinθ

F = (3000 x 9.8 x sin14)

F = 7,112.5 N

The net force of the helicopter  is calculated as follows;

F (net) = drag force + thrust force

F (net) = - 1200 N + 7,112.5 N

F (net) = 5,912.5 N

The acceleration of the helicopter is calculated as follows;

F (net) = ma

where;

m is the mass of the helicoptera is the acceleration

a = F (net) / m

a = 5,912.5 / 3000

a = 1.97 m/s²

Thus, since the acceleration of the helicopter is positive, the speed of the system is increasing towards to the right

Learn more about net forces here: https://brainly.com/question/14361879

#SPJ1

A box is released from rest and slides down a ramp in a closed system. Even though the box speeds up, its kinetic energy at the bottom of the ramp is less than the potential energy that it had at the top of the ramp.

What best explains why the box’s final kinetic energy is less than its initial potential energy?

In a closed system, kinetic energy is always less than potential energy.
Some potential energy was converted into thermal energy due to friction.
The acceleration due to gravity became smaller as the box slid down the ramp.
In a closed system, total energy is constantly being lost to outside objects.

Answers

The best explanation why the box’s final kinetic energy is less than its initial potential energy is that some potential energy was converted into thermal energy due to friction.

option B is the correct answer.

What is the law of conservation of energy?

The law of conservation of energy states that energy can neither be created nor destroyed but can be converted from one form to another.

According to law of conservation of energy, we have the following energy conversion process.

potential energy to kinetic energykinetic energy to potential energychemical energy to electrical energypotential energy to heat and kinetic energy, etc

In absence of friction, the potential energy of the box at the top of the ramp is equal to the kinetic energy of the box at the bottom of the ramp.

In the presence of friction, some  potential energy will be converted into thermal energy due to friction and the final kinetic energy will be smaller than the initial potential energy.

Learn more about conservation of energy here: https://brainly.com/question/166559

#SPJ1

Answer:

The answer above is correct (I just did it on Edge.) - It's option B!

Explanation:

Hope this helped - brainliest would be greatly appreciated!

Have a great day :D

A simple harmonic wave of wavelength 18.7 cm and amplitude 2.34 cm is propagating in the negative x-direction at 38.0 cm/s.
Part A. Find its angular frequency.
Part B. Find its wave number.
Part C. Write a mathematical expression describing the displacement y of this wave (in centimeters) as a function of position x and time t measured in cantimeters and seconds, respectively. Assume the maximum displacement occurs at x = 0 when t = 0 .

Answers

a) Angular frequency is  12.75 rad/s b)  The wave number is 33.59m c)

y ( x ,t) = 2.34  x  sin(33.59 x - 12.75t)

Given,

wavelength = λ = 18.7 cm

                   = 0.187 m

amplitude , A = 2.34 cm

v = 0.38 m/s

A) angular frequency = ?

f = v/λ

f = 0.38/1.87 = 2.03

angular frequency ,

ω = 2π f

ω = 2π x 2.03

ω = 12.75 rad/s

B) the wave number,

K = 2π/λ = 33.59m

c) as the wave is propagating in -x direction, the sign is positive between x and t

y ( x ,t) = A sin(k  x - ω t)

y ( x ,t) = 2.34  x  sin(33.59 x - 12.75t)

Learn more about angular frequency here:

https://brainly.com/question/14244057

#SPJ4

you are holding short for an intersection departure on runway 8 with the sign in front of you. which way should you turn when taxiing onto the runway to depart runway 8?

Answers

With the sign in front of you, you are waiting in short formation for an intersection taxiing on runway 8. In order to depart from runway 8, you should turn left as you enter the runway.

In contrast to towing or pushback, where the aircraft is moved by a tug, taxing (sometimes written taxying) is the movement of an aircraft on the ground under its own power. Although the name refers to vehicles with wheels most often, it also covers vehicles with skis or floats.

Taxiways are used by airplanes to go between locations on an airport, such as from a hangar to the runway. The takeoff roll and landing rollout, which are the accelerating run and descending run along a runway, respectively, before takeoff and landing, respectively, are not referred to as "taxiing."

Learn more about taxiing here:

https://brainly.com/question/15206908

#SPJ4

A wire of cross sectional area of 6 * 10 ^ - 5 * m ^ 2 length 50cm stretches by 0.4mm under a load of 3000N. What is the Young's Modulus of the wire?​

Answers

The Young's Modulus of the wire of length 50 cm is 4.0×10⁵ N/m.

What is young's modulus?

Young's modulus is a measure of the ability of a material to withstand changes in length when under lengthwise tension or compression.

To calculate the young's modulus of the wire, we use the formula below.

Formula:

γ = (F/A)/(L/e).................. Equation 1

Where:

γ = Young's modulusF = ForceA = AreaL = Length of the wiree = Extension

From the question,

Given:

F = 3000 NA = 6×10⁻⁵ m²L = 50 cm = 0.05e = 0.4 mm = 4×10⁻⁴ m

Substitute these values into equation 1

γ = (3000/6×10⁻⁵)/(0.05/4×10⁻⁴)γ = 4.0×10⁵ N/m

Hence, the Young's Modulus is 4.0×10⁵ N/m.

Learn more about young's modulus here: https://brainly.com/question/28757637

#SPJ1

coherent red light illuminates two narrow slits that are 25 cm apart. will a two-slit interference pattern be observed when the light from the slits falls on a screen? explain.

Answers

No two-slit interference pattern be observed when the light from the slits will not falls on a screen.

Because the condition of the interference is the distance between the slits equals or close to the wavelength of the red light. For distance of 25 cm, it is a very large distance that prevents the interference of the red light to occur. So, the answer is no.

Interference is the phenomenon where two waves combine by applying a displacement at any one point in space and time to form waves of greater, lesser or equal amplitude. Constructive and destructive interference arise from correlated or coherent wave interactions. This is because they originate from the same source or have the same or nearly the same frequency. Interference effects can be observed in all kinds of waves: light, radio waves, sound, surface water, gravity, matter waves.

Learn more about interference here : https://brainly.com/question/9655287

#SPJ4

an under-excited generator a. absorbs reactive power from the system. b. neither absorbs nor delivers reactive power. c. delivers reactive power to system.

Answers

An under-excited generator a. absorbs reactive power from the system

In an electrical power system, generators are used to produce electrical energy by converting mechanical energy into electrical energy. Under-excited generators are generators that are operating at a voltage below their rated value. These generators are used where it is necessary to maintain a specific voltage in the electrical system. For example, in some power systems, load on the generator may vary, and generator may need to adjust its output to match the changing load.

When a generator is under-excited, it absorbs reactive power from the system, which is a type of electrical power that is not used to do work. Reactive power is required to create and maintain the alternating current in an electrical system, but it does not perform any useful work. Absorbing reactive power helps to maintain the proper voltage and frequency in the system.

Read more about generators on:

https://brainly.com/question/24158806

#SPJ4

a ball rolls horizontally off the edge of a cliff at 4.00 m/s. if the ball lands a distance of 30.0 m from the base of the vertical cliff, what is the height of the cliff?

Answers

When a ball rolls horizontally off the edge of a cliff at 4.00 m/s, then the height of the cliff is calculated as 276 m.

What is projectile motion?

The motion of any object thrown or projected into the air is called projectile motion. Form of motion experienced by object that is projected in a gravitational field is called projectile motion.

d is distance ;velocity is  v= 4m/s

As, d = v t

30.0 = 4.00 t

So, t = 7.50 s

We know that, h = 1/2 g t^2

h = 1/2 (9.81) (7.5)^2

h = 275.9

Hence, h = 276 m

The height of the cliff is 276 m.

To know more about projectile motion, refer

https://brainly.com/question/24216590

#SPJ4

five hockey pucks are sliding across frictionless ice. the drawing shows a top view of the pucks and the three forces that act on each one. the forces can have different magnitudes (f, 2f, or 3f), and can be applied at different points on the puck. only one of the five pucks could be in equilibrium. which one?

Answers

When a hockey puck with a momentum of 5 kg-m/s is struck by a hockey stick, it receives an impulse of 100 N.

The force of friction is the imbalanced force in the situation of an already moving object (such as a puck sliding on an ice surface). In this situation, the puck's acceleration (slowing) is proportional to the amount of friction. More friction causes the puck to slow down faster. According to Newton's third law of motion, every action has an equal and opposite response. When a player is skating, for example, his skates push off the ice, causing an opposing reaction that propels the player ahead and increases his speed.

Learn more about acceleration here-

https://brainly.com/question/12550364

#SPJ4

what is the resistance of a conductor that carries a current of 120 amperes when the potential difference between its ends is 240 volts?

Answers

The resistance of a conductor that carries a current of 120 amperes when the potential difference between its ends is 240 volts = 2 Ω

Electrical resistance

Electrical resistance is the force that opposes the flow of current, it's a component that can reduce the speed and quantity of the flow of electrons in an electric circuit.

The formula for electrical resistance can be seen to have several components, namely R is the resistance (Ω), V is the voltage (V), and I is the current strength (A).

The equation:

R = V/I

We have,

Current strength = 120 A

The potential difference between its ends  = 240 V

So, the resistance of a conductor that carries a current of 120 amperes when the potential difference between its ends is 240 volts:

R = 240 V / 120 A

= 2 Ω

Learn more about electrical resistance here: https://brainly.com/question/17294367

#SPJ4

How does changing the mass or speed of a moving object before it collides with
another object affect the forces on those objects during the collision?



PLEASE HURRY

Answers

Answer:

When two objects collide, the forces that are exerted on each other are determined by their masses and speeds. If the mass of one of the objects is increased, the force that it exerts on the other object during the collision will also increase. Similarly, if the speed of one of the objects is increased, the force that it exerts on the other object during the collision will also increase. In general, the greater the mass and speed of an object, the greater the force that it will exert on another object during a collision. However, it is important to note that the direction of the forces will remain the same, regardless of the masses or speeds of the objects involved.

under the influence of its drive force, a snowmobile is moving at a constant velocity along a horizontal patch of snow. when the drive force is shut off, the snowmobile coasts to a halt. the snowmobile and its rider have a mass of 136 kg. under the influence of a drive force of 205 n, it is moving at a constant velocity whose magnitude is 5.50 m/s. the drive force is then shut off. (a) calculate the distance in which the snowmobile coasts to a halt. (b) calculate the time required for the snowmobile to stop.

Answers

A) 13.2 m, The snowmobile moves at a constant speed when the drive force is engaged; as the acceleration is zero, there is no net force. On the other hand, the net force is the product of two forces acting on the snowmobile: the driving force, F, and the frictional force, Ff: F-Ff=0, Ff=F.

(b) 4.2 s, The relationship between the snowmobile's acceleration and time t is given by: a=v-u/t, The time it takes the snowmobile to stop is 4.2 seconds after rearranging for t and entering numbers.

How do you define magnitude?

The simplest definition of magnitude in physics is "distance or quantity." In either an absolute or relative meaning, it displays the size or motion of an object.

To know more about Magnitude visit:

https://brainly.com/question/29766788

#SPJ4

Hi, Guy I need help with thi quetion:

Find the angle of refraction of a ray of light that enter diamond from water at an angle of 21. 2 degree to the normal. Can omeone help me fatttt!

Answers

The angle of refraction of the ray of light entering the Diamond is 16.8°.

The diamond from the water at an angle of 21.2 degrees to the normal.

According to the law of refraction, the ratio of the sign of the angle of incidence and the angle of refraction of the ray of light is constant.

Sin i/Sin r = n

n is the refractive index of the material in which the light is entering.

The refractive index of the Diamond is 2.42.

Putting all the values,

Sin(21.2°)/Sin(r) = 2.42

0.71/Sin(r) = 2.42

Sin(r) = 0.71/2.42

Sin(r) = 0.29

r = Sin inverse (0.29)

r = 16.86°

So, the angle of refraction is found to be 16.86°.

To know more about angle of refraction, visit,

https://brainly.com/question/12469161

#SPJ4

Question 19(Multiple Choice Worth 2 points) Which statement best describes scientific theories? Scientific theories are based on facts that describe natural events. Scientific theories describe natural events but do not explain them. Scientific theories are facts based on observations of events in the natural world. Scientific theories attempt to explain how events occur in the natural world.

Answers

Answer:

Scientific theories are attempts to explain how events occur in the natural world.

Explanation:

A scientific theory is an explanation for a wide range of observations and phenomena that have been tested and supported by multiple lines of evidence. A theory is not based on a single piece of evidence, but rather on a collection of evidence that has been accumulated over time through careful observation and experimentation.

Scientific theories are based on facts, which are observations of events in the natural world. However, a theory goes beyond simply describing these events; it seeks to explain why and how they occur. For example, the theory of evolution explains how organisms have evolved over time through natural selection. It is based on a wide range of evidence, including observations of the fossil record, comparative anatomy, and molecular biology, among others.

Overall, scientific theories are important tools for understanding and explaining the natural world, and they are constantly being revised and updated as new evidence becomes available.

2. what property of tissue does a proton density image show? what tr and te times do we need to achieve proton density imaging?

Answers

In a proton density image the tissue magnetization, RF signal intensity, and image brightness are.

Proton Mail is the world's largest cozy e-mail provider. It gives end-to-cease encryption and plenty of different splendid safety capabilities to maintain your communications non-public. Even the company hosting your emails has no manner of reading them, so you can rest confident that they cannot be studied via third events either.

It has a completely, very wealthy internal shape. you could have heard that protons are made up of 3 smaller basic particles known as quarks, two united states, and one down quark to be particular, but it is only the top of the particle iceberg, as proton researcher Paul Reimer explains.

One or extra protons are present in the nucleus of every atom. They provide the attractive electrostatic crucial force which binds the atomic electrons. The quantity of protons in the nucleus is the defining belongings of an element and is referred to as the atomic quantity.

Learn more about proton here:-https://brainly.com/question/1805828

#SPJ4

Other Questions
What is traditional American Christmas dinner? printing with inks was first practiced in which country in the third century ce? question 1 options: afghanistan china italy germany the united states of america Pete wants to set the playback quality parameter of the movie where the display quality of the video is favored over the playback speed. Which of the following values of the quality parameter must he apply to accomplish this? A. low B.true C. false D. High a 0.450 kg mass suspended from a spring oscillates with a period of 1.50 s. how much mass must be added to the object to change the period to 2.00 s? You will be creating an export business plan. Work must be original to this class, otherwise a grade of zero will be given. If no paper is submitted, a course grade of zero points will be given. Papers that do not contain detailed research will be severely penalized. No Wikipedia references are allowed.You do not need to submit work in progress. However you are welcome to approach your instructor with questions.Business Plan RequirementsBusiness Plan Page recommendations Section header Summary Part I: Purpose 1 Purpose Why has the plan been written? Part II: Table of Contents 1 Table of Contents Table of contents Part III: Executive Summary 1 Executive Summary This is short and concise. It covers the principal points of the report, and is prepared after the plan has been written. Part IV: Research 7 pages Introduction Introduction what product and foreign country did you select and why Situational Analysis Describe the product to be exported Present a brief history of the country as it relates to its origins and trade history Cultural Overview The norms, practices, social structure, etc. that may aid (or hinder) the reception of your product Consumer attitudes toward product Educational levels; ability to comprehend instructions, ability to use product Languages; labels, instructions Political Environment An overview of the governance structure of the country along with any legal-political forces Certain required or prohibited features Label and packing requirements Export Marketing Plan Long and short-term goals, characteristics of an ideal target market for your product given the country selected, market screening Economic Decelopment How developed the country is, and how this will influence the success of your product Purchasing power Wages Infrastructure Summary Summary Part V: References 1 to 2 References ReferencesNote: For further details regarding the components of your Export Business Plan, please see pages 468-469 of your textbook.Formatting RequirementsYour paper must be in APA format to include:The use of headings and subheadingsTimes New Roman 12-point font1 inch marginsParagraphs with a minimum of at least 5 sentencesThe first line of each paragraph should be indented 1/2 inchAnything less than the content length stated above is not sufficient coverage of content and will result in a substantial reduction in grade.At least one to two reference (or works cited) pages.References must be no older than 5 years.Your paper should be well-organized with excellent flow and excellently formatted. Check that your headings and sub-headings are correct.Spell-check and proofread before submission. consider the titration of 100.0 ml of 0.016 m hocl (ka=3.5108) with 0.0400 m naoh. if businesses and consumers become pessimistic, the federal reserve can attempt to reduce the impact on the price level and real gdp by group of answer choices increasing the money supply, which lowers interest rates. decreasing the money supply, which raises interest rates. decreasing the money supply, which lowers interest rates. increasing the money supply, which raises interest rates. next Middle kingdom of Egypt four ways to gain wealth Determine how many grams of CO2 are produced by burning 7.49 g of C4H10 convert the following equation into slope intercept form. 2x - 4y = 8 the distance to the cosmological horizon depends on (a) the age of the universe. (b) the number of galaxies in the universe. (c) the location of the outer edge of the universe. g. Cualquier fuente adicional de informacin que probara ser til a los usuarios. g hich of the following are examples of securities? select one: a. debentures b. stocks c. debentures, warrants, and stocks d. warrants dr. fletcher is taking six american sociology students on a study abroad trip to sweden. because the six american students have a common cultural, linguistic and ancestral heritage, they share the same: As planets solidify after their initial, formation they give off gases. If they have a strong enough gravitational field, they may hold onto some gases and form an atmosphere. Genreally, the stronger the gravity the thicker the atmosphere. Which of the following planets shold have the thickest atomsphere a patient with a t4 spinal cord injury asks the nurse if he will be able to be sexually active. which initial response by the nurse is best? help pls i dont understand this cause my teacher cant teach wound infections are commonly caused by staphylococcus species, common inhabitants of the nostrils and the skin. these organisms are What's Santa's name in Russia? Match each equation with the name of its form.