Calculate the acceleration of a car (in km/hâs) that can go from rest to 130km/h in 5.0s .

Answer:

Explanation:

The principle culture that transferred Greek astronomical knowledge to Renaissance Europe was Byzantine.

The moments of inertia for all component bodies is [tex]I_{1}[/tex]+ [tex]I_{2}[/tex] + [tex]I_{3}[/tex] + [tex]I_{4}[/tex].

To calculate the moment of inertia about the axis through the point at one corner of the rectangle, we need to consider the individual moments of inertia of each component body and then sum them up. Here's the calculation for each component:
1. Uniform disk of radius (r) and mass ([tex]m_{1}[/tex]):
Moment of inertia  [tex]I_{1}[/tex] = (1/2) * [tex]m_{1}[/tex] *[tex]r^{2}[/tex]
2. Uniform rod of length (L) and mass ([tex]m_{2}[/tex]):
Moment of inertia [tex]I_{2}[/tex]= (1/3) * [tex]m_{2}[/tex] *[tex]L^{2}[/tex]
3. Uniform rectangle with side lengths (a) and (b), and mass ([tex]m_{3}[/tex]):
Moment of inertia  [tex]I_{3}[/tex] = (1/12) * [tex]m_{3}[/tex] * ([tex]a^{2}[/tex] + [tex]b^{2}[/tex])
4. Point mass ([tex]m_{4}[/tex]V) at a distance (d) from the axis:
Moment of inertia  [tex]I_{4}[/tex] = [tex]m_{4}[/tex] * [tex]d^{2}[/tex]

Learn more about inertia here: https://brainly.com/question/3268780

#SPJ11

The type of electromagnetic radiation is Radiowaves which have a wavelength of 10 meters.

Since these waves have a longer wavelength, they are used for communication over long distances. Some examples of sources that emit these radiations - radiowaves - are TV and radio stations, cell phone towers, as well as satellites.

Radio waves are very beneficial as they can travel long distances without any power losses and getting absorbed or scattered by the atmosphere. Also, radio waves are non-ionizing and generally considered safe for human exposure. They are widely used in many applications, including broadcasting, navigation, remote sensing, and medical imaging.

For more info on electromagnetic radiation visit,

https://brainly.com/question/10759891

#SPJ4

a. The skin is the correct option. Microwave-induced injury is best understood when it involves the skin. Microwaves are a form of electromagnetic radiation that can cause heating effects on living tissues. When the skin is exposed to microwaves, the energy is absorbed, causing an increase in temperature that may lead to tissue damage.

Squamous cell destruction is a term related to the damage or destruction of squamous cells, which are flat, scale-like cells that make up the outer layer of the skin called the epidermis. While microwaves can cause damage to these cells, the broader category of microwave-induced injury on the skin encompasses a wider range of possible effects, making it a better-understood phenomenon.
Excessive heating of internal organs, such as the liver, can occur due to microwave exposure, but the mechanisms and effects are less well-understood than those involving the skin. The skin acts as the first line of defense against microwave radiation, making it more susceptible to injury compared to deeper organs.
To summarize, microwave-induced injury is best understood when it involves the skin, as the skin absorbs microwave radiation and is prone to temperature increases that can cause tissue damage, including squamous cell destruction. Other effects of microwaves, such as excessive heating of internal organs, are less well-understood, making the skin the primary focus of study for this type of injury.

For more information on  squamous cells see:

https://brainly.com/question/30489088

#SPJ11

The combined resistance of two 1-ohm resistors in series is 2 ohms, while the combined resistance of the same resistors in parallel is 0.5 ohms.

Resistors in series add up their individual resistances, so when two 1-ohm resistors are connected in series, their combined resistance is the sum of 1 ohm + 1 ohm = 2 ohms.

On the other hand, when resistors are connected in parallel, their combined resistance is less than the individual resistance of each resistor. This is because the current has multiple paths to flow through, reducing the overall resistance.
The way resistors are connected impacts their combined resistance. When in series, the resistances add up, and when in parallel, the resistances decrease.

For more information on resistors kindly visit to

https://brainly.com/question/15242615

#SPJ11

The given statement "In general, as a reaction proceeds to make more products, reaction rate decreases" is true.

This is because as the concentration of reactants decreases, there are fewer collisions between particles, leading to a slower rate of reaction. Additionally, some reactions may also be limited by factors such as the availability of reactants or the presence of catalysts.

However, there are some reactions where the opposite may be true, such as in a chain reaction where the formation of one product can trigger the formation of more products, leading to an increase in reaction rate.

For more such questions on reaction, click on:

https://brainly.com/question/28825595

#SPJ11

Everyone is subject to natural background radiation is (a). true statement because natural background radiation, which includes radiation from the environment and natural sources including radon gas from the ground, cosmic rays from space, and radioactive elements in the earth's crust, is a risk to everyone.

Humans are inevitably exposed to this type of radiation on a regular basis, albeit the amounts differ according to altitude, geography, and other factors. The amount of ionizing radiation in the environment at a specific location that isn't the result of intentional introduction of radiation sources is known as background radiation.

There are many different natural and man-made sources of background radiation. In addition to man-made medical X-rays, radioactive fallout from nuclear weapons testing, and nuclear accidents, these include cosmic radiation as well as environmental radioactivity from naturally occurring radioactive minerals (such as radon and radium).

To know more about natural

https://brainly.com/question/10423822

#SPJ4

Answer:

Explanation:

When the wavelength becomes larger the amplitude of the wave becomes shorter. This is the reason when a Tsunami occurred less damage to the ships in deep sea.

In a simple circuit that consists of a battery, light bulb, and connecting wires, the current at point B, near the negative terminal of the battery, is equal in magnitude to the current at point A, near the positive terminal of the battery.

This is because the current flows in a closed loop, starting from the positive terminal of the battery, flowing through the light bulb and returning back to the negative terminal of the battery. Therefore, the current is the same at any point in the circuit. However, the direction of the current flow is opposite at the negative and positive terminals of the battery. At the negative terminal, the current flows from the battery to the circuit, while at the positive terminal, it flows from the circuit to the battery.

To know more about simple circuit click here:

https://brainly.com/question/22667470

#SPJ11

In small communities and rural places, a slow sand filter is recommended for use.

This type of filter is effective, low-cost, and easy to maintain, making it suitable for these settings. For small communities and rural places, slow sand filters are often recommended as they are low cost, low maintenance, and effective in removing a wide range of contaminants. Slow sand filters use a combination of biological and physical processes to remove particles and pathogens from water. They work by passing water slowly through a bed of fine sand, which acts as a physical filter, and a layer of microorganisms, which help to break down and remove organic matter and pathogens. Slow sand filters have been used for centuries and are still widely used today in many parts of the world.

To learn more about slow sand filter, refer:-

https://brainly.com/question/13042158

#SPJ11

Intermodal option combines truck and rail transportation with conventional road trailers carried atop rail flatcars for the long (line-haul) segment of the transit (d). Trailer on Flatcar is correct option.

For the long-distance (line-haul) leg of transit, trailer on flatcar, sometimes referred to as TOFC or piggyback, combines truck and rail transportation. In this manner, pickup and delivery at the origin and destination sites are handled by trucks while standard road trailers, or "pigs," are loaded onto rail flatcars and transported by rail for the long run. This enables the use of trucks' flexibility for the initial and last miles of transit while still utilizing the long-distance efficiency of rail transportation.

To know more about Intermodal

https://brainly.com/question/14310766

#SPJ4

To find the instantaneous tangential speed of passengers 15 seconds after acceleration begins, we need the initial velocity and acceleration values. Then, we can use the linear motion formula to calculate the speed at that specific time.

To determine the instantaneous tangential speed of passengers 15 seconds after acceleration begins, we need more information about the acceleration and initial velocity. However, I can provide a general explanation of these terms and how to solve such a problem.
Instantaneous speed refers to the speed of an object at a specific moment in time. In this case, it's the speed of the passengers 15 seconds after the acceleration starts.
Tangential speed refers to the linear speed of an object as it moves along a circular path. In this context, passengers are assumed to be moving in a circular motion, and we need to find their speed at the specified time.
Once we have the initial velocity (v0), acceleration (a), and time (t = 15 seconds), we can use the formula for final velocity (v) in linear motion:
v = v0 + at
If given the necessary values, we could plug them into the formula to find the instantaneous tangential speed at t=15s and choose the correct answer among the given options (A, B, C, D, or E).
In summary, to find the instantaneous tangential speed of passengers 15 seconds after acceleration begins, we need the initial velocity and acceleration values. Then, we can use the linear motion formula to calculate the speed at that specific time.

learn more about tangential here

https://brainly.com/question/14993737

#SPJ11

The two ways that inertia affect the motions of the planets are:

B. It keeps the planets from flying off into space, out of the solar system.

C. It causes the planets to keep moving in the same direction as they did when they formed.

Inertia helps to keep planets in their orbits around the Sun, preventing them from flying off into space. As the planets move around the Sun, they are constantly pulled by the Sun's gravity towards the center of their orbit. However, due to their inertia, they continue to move forward, and the resulting combination of the inward pull of gravity and the outward motion due to inertia causes the planets to move in stable, elliptical orbits.

The planets formed from a cloud of gas and dust that was rotating in a particular direction. Due to the conservation of angular momentum, this rotation was transferred to the planets as they formed, causing them to continue to rotate in the same direction as they did when they formed. This is an example of how inertia affects the motion of the planets.

Learn about motions of planet here https://brainly.com/question/986278

#SPJ1

Microwaves, which are a type of electromagnetic radiation, are reflected by surfaces that are metallic or have high electrical conductivity, such as metals, aluminum foil, and certain types of plastics. These surfaces can cause the microwaves to bounce back instead of being absorbed, leading to uneven heating and potential damage to the microwave.  

These materials can include aluminum foil, metal mesh, and certain metallic coatings. When microwaves encounter these surfaces, their energy is unable to pass through and is instead reflected back, often causing an even distribution of energy in the microwave oven.

It is important to always use microwave-safe dishes and avoid placing any metal objects inside the microwave.

To know more about Microwaves:

https://brainly.com/question/4537604

#SPJ11

The order of increasing force of attraction between submicroscopic particles is (c) air < (b) water < (a) sugar.

This is because sugar molecules have stronger intermolecular forces of attraction than water, and air molecules have weak intermolecular forces of attraction compared to both sugar molecules and water molecules.Force of attraction is a force that pulls the body near due to its attraction. There are numerous attractive forces prevailing in nature. Some of them are magnetic force, electric force, electrostatic force and gravitational force

To know more about force  please click:-
https://brainly.com/question/807785

#SPJ11

If fusion reactions in the Sun suddenly shut off, we would be able to tell by observing a decrease in the Sun's energy output and changes in its surface features.

Fusion reactions in the Sun's core are responsible for producing the energy that the Sun emits as light and heat. If these reactions were to suddenly shut off, the Sun's energy output would decrease, and we would observe a reduction in the amount of light and heat reaching Earth. We could measure this decrease in energy output using instruments such as satellites and telescopes. In addition to changes in the Sun's energy output, we would also expect to see changes in its surface features. The Sun's surface is constantly in motion due to the convection of its plasma, which is driven by the energy produced in the core. If the energy production were to stop, the convection would also stop, leading to changes in the Sun's magnetic field and surface features such as sunspots and solar flares. We could observe these changes using telescopes that are designed to capture images of the Sun's surface.

Learn more about fusion reactions here:

https://brainly.com/question/11114418

#SPJ11

The given statement, "It is believed by some researchers that the hazards of low level radiation may be worse than previously predicted, supporting the principle that "x-rays should be used only when there is good medical reason." is true because a lot of research is being done to determine the biological causes of radiation damage to DNA and cells.

Ionizing radiation has always been a risk to human populations, but it is now even more prevalent because of its usage in agriculture, industry, and the military forces. While the health dangers from medium and high doses of radiation are generally established, those from lower levels are less so.  Confusion has been caused for the public as well as for decision-makers by conflicting messages on the safety of low doses of radiation from various sources.  

To know more about researchers

https://brainly.com/question/17181096

#SPJ4

Refer to the attached image.

True. When conductors of different insulation types are associated together, the limiting temperature of any conductor should not be exceeded.

Equation 310-15(3) is a reference to section 310-15 of the National Electric Code (NEC) which outlines rules for sizing conductors based on factors such as current-carrying capacity and temperature ratings. In this case, the statement is referring to situations where conductors with different types of insulation are used together, and emphasizes the importance of ensuring that the temperature limit for any individual conductor is not exceeded. This is critical for ensuring safe and reliable operation of electrical systems. This is to ensure the safety and proper functioning of all conductors, as well as preventing damage to the insulation and potential electrical hazards.

Learn more about conductors here: https://brainly.com/question/8426444

#SPJ11

The speed of block C after the collisions is v/6.

What is Momentum?

Momentum is a physical quantity that measures the motion of an object. It is the product of an object's mass and velocity. The momentum of an object in a particular direction is given by the formula: p = m*v, where p is the momentum, m is the mass of the object, and v is its velocity. The momentum of an object can be changed by applying a force to it, resulting in an acceleration that will cause a change in velocity, and therefore, a change in momentum.

By conservation of momentum, the total momentum before the collision is equal to the total momentum after the collision. Before the collision, block A has momentum mv, and blocks B and C have zero momentum. After the collision between A and B, the two blocks move together with momentum (m + 2m)v = 3mv. By conservation of momentum, the momentum of block C after the collision is also 3mv, since there are no external forces acting on the system of blocks.

After the collision between blocks A and B, the total mass of the two blocks is m + 2m = 3m, so their velocity is v/3. When they collide with block C, the total mass of the three blocks is m + 2m + 3m = 6m, so their velocity after the collision is (v/3)(3) / 6 = v/6.

Learn more about Momentum

https://brainly.com/question/1042017

#SPJ1

The smallest size conductor permitted for branch circuits, feeders, and services for residential, commercial, and industrial locations is 14 AWG.

The smallest size conductor permitted for branch circuits, feeders, and services for residential, commercial, and industrial locations is #14 AWG (American Wire Gauge) for copper and #12 AWG for aluminum or copper-clad aluminum. However, there are some exceptions to this rule, such as certain motor circuits and special applications, which may require larger conductor sizes.

AWG stands for American Wire Gauge, which is a standardized system used for measuring the diameter of electrically conducting wire. It is commonly used in North America for both copper and aluminum wire, and it assigns a specific numerical value to each wire size, ranging from 0000 (largest) to 40 (smallest). As the AWG number increases, the diameter of the wire decreases. The AWG system is used to ensure consistency in wire sizing across different manufacturers and applications.

To know more about conductor

brainly.com/question/8426444

#SPJ11

Typical filtration rates for dual media filters in conventional treatment plants can vary, but generally range from 2 to 6 gallons per minute per square foot of filter media.

The media used in these filters typically consists of a combination of sand and anthracite, with the sand providing larger pores for initial filtration and the anthracite providing smaller pores for final filtration. These filters are an important component of conventional treatment plants, as they help to remove suspended particles and impurities from water before it is disinfected and distributed for use.  Dual media filters, which often consist of layers of sand and anthracite, provide improved filtration efficiency and increased filter run times compared to single-media filters.

Learn more about plants here:

brainly.com/question/15092720

#SPJ11

The summary, the minimum interruption rating for circuit breakers is 5,000 amperes, and 10,000 amperes for fuses, according to the [tex]NEC[/tex].

According to the National Electrical Code[tex](NEC)[/tex] sections [tex]240-60(c)[/tex] and [tex]240-83(c)[/tex], overcurrent devices must be designed and rated to clear fault current and must have a short-circuit interrupting rating sufficient for the available fault levels.

The minimum interruption rating for circuit breakers is 5,000 amperes, and 10,000 amperes for fuses.

The interrupting rating of an overcurrent device refers to its ability to safely interrupt or break the circuit during a short circuit or fault condition.

The interrupting rating is determined by the available fault current at a specific location and is expressed in amperes.

For circuit breakers, the [tex]NEC[/tex] requires a minimum interrupting rating of 5,000 amperes.

This means that the circuit breaker must be able to safely interrupt or break the circuit during a fault condition with a maximum available fault current of 5,000 amperes.

For fuses, the [tex]NEC[/tex] requires a minimum interrupting rating of 10,000 amperes. This means that the fuse must be able to safely interrupt or break the circuit during a fault condition with a maximum available fault current of 10,000 amperes.

It's important to note that the interrupting rating is just one of several factors to consider when selecting an overcurrent device.

Other factors include the continuous current rating, the trip curve, and the voltage rating.

The selected overcurrent device must be able to handle the expected load and any anticipated fault conditions.

In summary, the minimum interruption rating for circuit breakers is 5,000 amperes, and 10,000 amperes for fuses, according to the [tex]NEC[/tex].

Learn more about interruption

brainly.com/question/29770273

#SPJ11

The vertical distance an object dropped from rest on this distant planet covers in 1.3 seconds is 18.59 meters.

To calculate the vertical distance an object dropped from rest on this distant planet covers in 1.3 seconds, we can use the following equation of motion:
d = vi * t + 0.5 * a * t^{2}
where d is the vertical distance, vi is the initial velocity (0 m/s, since the object is dropped from rest), a is the acceleration (22 m/s^{2}), and t is the time (1.3 s).
Step 1: Substitute the given values into the equation:
d = 0 * 1.3 + 0.5 * 22 * (1.3)^{2}
Step 2: Perform the calculations:
d = 0 + 0.5 * 22 * 1.69
d = 11 * 1.69
Step 3: Calculate the final value:
d ≈ 18.59 m
So, the object dropped from rest on this planet with an acceleration of 22 m/s^{2} covers a vertical distance of approximately 18.59 meters in 1.3 seconds.

learn more about acceleration Refer: https://brainly.com/question/30660316

#SPJ11

Roentgen Equivalent Man. The term rem is a unit of measurement used to quantify the amount of radiation someone is exposed to, taking into account the type of radiation and its potential to cause harm. It is a combination of the Roentgen energy measure and the radiation weighting factor.

The term "rem" is short for: Roentgen equivalent measure Rem stands for Roentgen equivalent measure, which is a unit used to quantify the biological effect of ionizing radiation. It takes into account the type of radiation and its energy, allowing for a comparison of different radiation exposures in terms of their potential harm to living organisms.also known as the equivalent dose.  One of the most important portions of the sleep cycle is called REM sleep. REM stands for Rapid Eye Movement, and it’s both the deepest and most active stage of sleep. REM is essential if you want to reap the full benefits of sleep and feel rested after a night in bed.

learn more about Roentgen here

https://brainly.com/question/31559773

#SPJ11

To determine the size conductor required to supply a 40 ampere non-continuous load in a raceway that contains four current-carrying conductors, you will need to consult the NEC (National Electrical Code) tables for conductor ampacity.

Based on the NEC tables, for four current-carrying conductors in a raceway, you will need a conductor rated for at least 70 amperes. Therefore, a 6 AWG (American Wire Gauge) copper conductor would be suitable for supplying a 40 ampere non-continuous load in this scenario. It is important to note that this answer assumes that the installation meets all other code requirements, such as proper wire insulation and protection.

To know more about National Electrical Code click here:

https://brainly.com/question/17215290

#SPJ11

If one of the wind turbines with different length blades is to spin more quickly, the angular acceleration, a should be positive. This means that the rate of change of the angular velocity should be in the direction of increasing speed.

To change the angular speed of one of the wind turbines with different length blades, you would need to adjust the angular acceleration (a). If the turbine is to spin more quickly, the angular acceleration (a) should be positive. A positive angular acceleration indicates an increase in angular speed, while a negative value would indicate a decrease in angular speed.

The angular acceleration is the time rate of change of the angular velocity and is usually designated by α and expressed in radians per second per second. For the case in which the angular velocity is uniform (nonvarying), θ = ωt and α = 0. If α is uniform but not zero, ω = αt and θ = 1/2αt².

Visit here to learn more about  angular acceleration : https://brainly.com/question/30237820
#SPJ11

Maximum range and maximum distance glide are performance characteristics of flight at maximum lift/drag ratio in a propeller-driven airplane. So, option b is right choice.

When a propeller-driven airplane is flying at maximum lift/drag ratio, it means that it is flying at its most efficient speed, where the lift generated by the wings is equal to the drag created by the airplane's motion through the air. This results in a number of performance characteristics that are beneficial for the aircraft.
One of the key characteristics of flight at maximum lift/drag ratio is the ability to gain altitude over a given distance. Since the airplane is operating at its most efficient speed, it is able to climb more easily and quickly than it would at other speeds.

This can be particularly important in situations where the airplane needs to gain altitude rapidly, such as during takeoff or when flying through turbulent air.
Another important characteristic of flight at maximum lift/drag ratio is the ability to achieve maximum range and maximum distance glide.

Since the airplane is operating at its most efficient speed, it is able to cover the greatest distance for a given amount of fuel, making it ideal for long-distance flights.

Additionally, if the airplane were to experience an engine failure, it would be able to glide for the greatest distance before needing to land.
Finally, flight at maximum lift/drag ratio is characterized by a high coefficient of lift and a low coefficient of drag. This means that the airplane is able to generate a greater amount of lift while producing less drag, which helps to maximize its efficiency.

The high lift coefficient also allows the airplane to fly at slower speeds, making it more maneuverable and easier to control.

So, option b is right.

For similar question on lift/drag ratio

https://brainly.com/question/30025752

#SPJ11

Question:-

What performance is a characteristic of flight at maximum lift/drag ratio in a propeller-driven airplane?

a.- gain in altitude over a given distance- range and maximum distance glide

b. - coefficient of lift and minimum coefficient of drag  200 words

The angular speed of the wheels is 20 rad/s. When  a bicycle with wheels of radius 0.4 m travels on a level road at a speed of 8 m/s.

The linear speed of a point on the edge of a wheel is equal to the product of the angular speed and the radius of the wheel. Therefore, we can use the formula:
linear speed = angular speed x radius
To find the angular speed, we can rearrange this formula as:
angular speed = linear speed / radius
Plugging in the given values, we get:
angular speed = 8 m/s / 0.4 m = 20 rad/s
Therefore, the angular speed of the wheels is 20 rad/s, the answer is (B) 20 rad/s.

learn more about angular speed Refer: https://brainly.com/question/9684874

#SPJ11

The Schwarzschild radius of Earth is 0.9 centimeters if it were to become a black hole.

The Schwarzschild radius is the distance from the center of an object at which the escape velocity becomes equal to the speed of light, and thus, the object becomes a black hole.

If the Earth were to shrink in size until it became a black hole, its Schwarzschild radius would be 0.9 centimeters.

This means that if the Earth were compressed to a size smaller than 0.9 centimeters, it would become a black hole. However, it is impossible for Earth to collapse to such a small size due to the repulsive forces between particles.

In summary, if the Earth were to become a black hole, its Schwarzschild radius would be 0.9 centimeters, but it is unlikely to happen in reality.

For more such questions on Schwarzschild radius, click on:

https://brainly.com/question/12647190

#SPJ11