an ideal vapor-compression refrigeration cycle operates at steady state with refrigerant 134a as the working fluid. saturated vapor enters the compressor at 2 bar, and saturated liquid exits the condenser at 8 bar. the mass flow rate of refrigerant is 7 kg/min. determine

Answers

Answer 1

the refrigeration capability, in tons, is 4.905 tons, the coefficient of performance, in kW, is 4.17 KW, and the compressor power, in kW, is 4.1336 KW.

Describe the compressor formula.

Electrical Expense = HP *.746 * hours * Kw cost * motor efficiency. As an illustration, consider a 50 HP compressor that consumes $.06 per Kwh of electricity and has a 90% efficiency electric motor. $5,172.26 is the yearly cost for 50 HP multiplied by.746 over 2,080 hours.

Compressor definition and operation

In order to create energy which can be kept in a tank for later use, air compressors work by applying pressure to atmospheric air. Similar to an open balloon, when the compressed air is purposefully released, pressure builds up, transforming the potential energy into productive kinetic energy.

To know more about compressor visit;

https://brainly.com/question/28963656

#SPJ4


Related Questions

part j bulb r4 is now removed from the circuit, leaving a break in the wire at its position. what is the current in the bulb r1 ? express your answer in amperes. templatessymbols undoredoresetkeyboard shortcutshelp i

Answers

I2 = V / R2 = 0.678 A ; I3 = V / R3 = 0.678 A are the current flows in R2 and R3.

Here R1 = R2 = R3 = R4 = 4.43Ω

And E = 9.01 V

When we removed the bulb bearing Ru, the equivalent circuit now becomes as shown.

Now R2 and R3 are in parallel, so their equivalent resistance

 1/Rp = 1/R2 + 1/R3

 Rp = 2.215 Ω

Again, R1 is connected Rp in series so equivalent resistance

R = R1 + Rp = 6.645 Ω

Current through ‘R1’ is

 I1 = V / R = 9.01 / 6.645 = 1.356 A

Potential across R2 and R3 is

 V = E – I1R1 = 3.0033V

So current through R2

  I2 = V / R2 = 0.678 A

Current through R3

 I3 = V / R3 = 0.678 A

To learn more about Electrical Circuits:

https://brainly.com/question/2969220

#SPJ4

a boy whose weight is 600N runs up a fight of stairs 10m high in 12s. what is his average power​

Answers

[tex]p = \frac{w}{t} [/tex]

[tex]w = fdcosθ [/tex]

where p is power

w is work done

t is time in seconds

f is force

d is distance

f=600N

d=10

t=12

w=600 X 10

w=6000 Nm

p=6000/12

p=500 watts

Important Formulas:

[tex]w=Fd[/tex]

[tex]p=\dfrac{w}{t}[/tex]

work(measured in joules) = force(measured in newtons) * distance(measured in meters)

power(measured in watts) = work(measured in joules) / time(measured in seconds)

__________________________________________________________

Given:

[tex]F=600N[/tex]

[tex]d=10m[/tex]

[tex]t=12s[/tex]

[tex]p=?[/tex]

__________________________________________________________

Finding work:

[tex]w=Fd[/tex]

[tex]w=600\times10[/tex]

[tex]w=6000J[/tex]

__________________________________________________________

Finding power:

[tex]p=\dfrac{w}{t}[/tex]

[tex]p=\dfrac{6000}{12}[/tex]

__________________________________________________________

[tex]\fbox{p = 500 watts}[/tex]

Identify the 5 stages of mitosis:
Phase
Picture
What happens
________

Chromosomes are visible, nuclear membrane breaks down, spindle fibers begin to form.
________


Sister chromatids line up at the center of the cell.
________


Sister chromatids are pulled apart and move to opposite poles of the cell.
________


Spindle fibers breakdown, nuclear membrane forms, and chromosomes begin to uncoil and form chromatin.
________


Cytoplasm splits in 2 and the cell divides.

Answers

Answer:

the first one is Interphase

the second one is prophase

the third one is metaphase

the fourth one is Anaphase

the last one is Telophase

A 6.5-N ball is thrown with an initial velocity of 20 m/s at a 35° angle from a
height of 1.5 m.
a. What is the velocity of the ball if it is caught at a height of 1.5 m?
b. If the ball is caught at a height of 1.5 m, how much mechanical work is
required?

Answers

Answer:

a. The velocity of the ball, if it is caught at a height of 1.5 m, is [14.9, 19.7] m/s.

To find the velocity of the ball if it is caught at a height of 1.5 m, we can use the equation:

vf^2 = vi^2 + 2ad

Where vf is the final velocity, vi is the initial velocity, a is the acceleration due to gravity (-9.8 m/s^2), and d is the change in position.

Plugging in the values given in the question, we get:

vf^2 = 20^2 + 2*(-9.8 m/s^2)*(1.5 m)

Solving for vf, we get:

vf = [14.9, 19.7] m/s

b. If the ball is caught at a height of 1.5 m, the mechanical work required is 0 J.

To find the mechanical work required, we can use the equation:

work = force * displacement

Plugging in the values given in the question, we get:

work = 6.5 N * (1.5 m - 1.5 m)

Solving for work, we get:

work = 0 J

Therefore, if the ball is caught at a height of 1.5 m, the mechanical work required is 0 J.

(1) Relief valves are used in pneumatic systems as damage-preventing units.
(2) Check valves are used in both hydraulic and pneumatic systems.
Regarding the above statements,
Both No.1 and No. 2 are true.
neither No. 1 nor No. 2 is true.
only No. 1 is true.

Answers

(1) Relief valves are components used in pneumatic systems to prevent harm. (2) Pneumatic and hydraulic systems both employ check valves. A- Both Nos. 1 and 2 are accurate in relation to the aforementioned assertions.

What do scientific units mean?

Any standard that is used to compare measurements is referred to as a unit. Measurements of a property that have been taken using various units—for example, inches to centimeters—can be accommodated using unit conversions.

What does SI mean in science?

The metric system, sometimes referred to as the SI, is the accepted unit of measurement on a global scale. World Metrology Day is an international holiday commemorating the signing of the International Treaty of the Meter in Paris on May 20, 1875, by seventeen nations, including the United States.

To know more about Units visit:

https://brainly.in/question/11622331

#SPJ4

why is there no gap in earths crust?


btw this is science it just doesn't appear as science in aa suubject

Answers

There is no gap in Earth's crust due to presence of magma beneath the Earth crust which usually erupt to fill the gap in the Earth crust.

What is great unconformity in Earth's crust?

There is a temporal gap that exist in Earth's known as the great unconformity.

The great unconformity is a massive temporal gap that can be found  famous crevasse and also in most places on the Earth's crust.

However, the great unconformity describes the temporal gap that exist in earth crust which disappears with time.

The presence of magma beneath the earth's crust ensures that there is no gap in Earth's crust as the magma always erupt upward to fill any gap between the Earth's crust and create new crust.

Thus, there is temporal gap in earth crust which disappears with time due to molten magma that erupts to fill the gap and create new crusts.

Learn more about Earth crust here: https://brainly.com/question/21302562

#SPJ1

A 47.0 kg cheetah can run with a speed of 31.0 m/s. What is the cheetah's kinetic energy?​

Answers

Answer:

22,583.5 J

Explanation:

KE = 1/2mv²

KE = 1/2(47 kg)(31.0 m/s)² = 22,583.5 J

a 2.6 kg particle moves along an x axis, being propelled by a variable force directed along that axis. its position is given by x

Answers

The value of the constant c is -17 m/s2.

What is the variable force about?

To find the value of the constant c, you need to use the information given about the position of the particle and the force acting on it at time t = 3.0 s.

The position of the particle at time t = 3.0 s is given by x = 3.0 m + (4.0 m/s)t + ct2 - (2.0 m/s3)t3. Substituting t = 3.0 s into this equation gives:

x = 3.0 m + (4.0 m/s)(3.0 s) + c(3.0 s)2 - (2.0 m/s³)(3.0 s)3

= 3.0 m + 12.0 m + 9c - 54 m/s³

= 3.0 m + 12.0 m - 54 m/s³ + 9c

The force on the particle at time t = 3.0 s has a magnitude of 36 N and is in the negative direction of the x-axis. This means that the force is directed opposite to the direction of the positive x-axis. Since the force is proportional to the acceleration of the particle, the acceleration of the particle at time t = 3.0 s must also be in the negative direction of the x-axis.

The acceleration of the particle at time t = 3.0 s is given by the second derivative of the position with respect to time:

a = [tex]d^{2} \frac{x}{dt^{2} } = 2c[/tex]

Since the acceleration is in the negative direction of the x-axis, the value of c must be negative.

Substituting the value of the acceleration into the equation for the position of the particle at time t = 3.0 s gives:

x = 3.0 m + 12.0 m - 54 m/s³ + 9c

= 3.0 m + 12.0 m - 54 m/s³ - 9(-a/2)

= 3.0 m + 12.0 m - 54 m/s³ + 9a/2

= 3.0 m + 12.0 m - 54 m/s³ + 9(-36 N)/2

= 3.0 m + 12.0 m - 54 m/s³ - 162 N

= -147 m - 54 m/s³

Since the position of the particle at time t = 3.0 s is given as -147 m, the value of c must be:

c = (-147 m - 54 m/s³) / (9 s2)

= -17 m/s²

Therefore, the value of the constant c is -17 m/s².

Learn more about variable force from

https://brainly.com/question/29494558
#SPJ1

See full question below

A 2.0 kg particle moves along an x-axis, being propelled by a variable force directed along that x-axis. Its position is given by x = 3.0 m + (4.0 m/s)t + ct2 - (2.0 m/s3)t3, with x in meters and t in seconds. The factor c is a constant. At t = 3.0 s, the force on the particle has a magnitude of 36 N and is in the negative direction of the axis. What is c?

speed of light is always the same no matter how fast you are moving is very strange and counterintuitive. t/f

Answers

The statement "the speed of light is always the same no matter how fast you are moving" is true. This phenomenon is known as the constancy of the speed of light.

According to the theory of relativity, the speed of light in a vacuum is a constant value that is independent of the motion of the observer. This means that no matter how fast you are moving, you will always measure the speed of light to be the same value.

This idea may seem strange and counterintuitive, but it has been experimentally verified and is now a fundamental principle of modern physics. It has important consequences for our understanding of the nature of space and time, and it has played a key role in the development of many important scientific theories, including the theory of relativity.

To know more about relativity

https://brainly.com/question/29258869

#SPJ4

Keisha writes that if an object has any external forces acting on it, then the object can be in dynamic equilibrium but not static equilibrium.

Answers

The statement best describes Keisha's error is an object in either state of equilibrium must have no net force acting on it. The correct option is D.

What is dynamic equilibrium?

When a system is in a state of dynamic equilibrium, the reversible reaction that is occurring in it no longer changes the ratio of reactants to products, but there is still the movement of substances between the reactants and products.

Because the thing will be moving, it won't be at rest. An object is considered to be static when it is at rest. The external forces that are acting on an object are what will make it move. When external forces are no longer acting on the object, it will travel up to that point.

Therefore, the correct option is D, An object in either state of equilibrium must have no net force acting on it.

To learn more about dynamic equilibrium, refer to the link:

https://brainly.com/question/27965641

#SPJ1

The question is incomplete. Your most probably complete question is given below:

Which statement best describes Keisha's error?

An object that is not moving is always in static equilibrium.

O An object that is moving must be in dynamic equilibrium.

An object in either state of equilibrium must have no forces acting on it.

An object in either state of equilibrium must have no net force acting on it.

Which statement is true

Cells usually take in large food molecules

Cells can get energy by breaking down molecules from food

Cells use energy to help an organism grow and live

Breaking down molecules does not release energy

Answers

All of the statements are true. Here's why:

Cells usually take in large food molecules. In order to get the nutrients and energy they need, cells have to take in large molecules like carbohydrates, proteins, and fats. These molecules are too big to pass through the cell membrane, so cells have to use specialized structures like lysosomes and vacuoles to break them down into smaller molecules.

Cells can get energy by breaking down molecules from food. When cells break down molecules from food, they release energy in the form of ATP (adenosine triphosphate). This energy can be used by the cell to power its functions, such as growth and metabolism.

Cells use energy to help an organism grow and live. The energy that cells get from

breaking down molecules from food is essential for maintaining the functions of the organism. Without this energy, cells would not be able to perform essential tasks like building new tissue, repairing damaged cells, and fighting off infections.
Breaking down molecules does not release energy.

Breaking down molecules actually requires energy, not releases it. In order to break down large molecules into smaller ones, cells have to use enzymes and other specialized structures. These processes require energy in the form of ATP, which is why cells need to take in energy from food in the first place.

A professor wants to conduct a study to investigate which kind of note-taking technique (hand-written or computer-based) is better for memory and recollection. He decides to split his class into two groups - hand-written notes and computer-based notes - and measure better memory and recollection via the next exam scores. The two note-taking groups are what variable in the study?


independent variable


dependent variable


control variable


extraneous variable

Answers

According to the professor's research, both handwritten notes and computer-based notes qualify as independent variables.

The professor's study considers handwritten notes and computer-based notes to be independent variables. These other qualities will be examined to see if they change depending on note-taking technique, including better memory and exam recall.

What kinds of variables are the groupings for taking notes?

Because they are being examined for their potential to influence other factors, the note-taking groups that use handwritten and computerised notes are regarded as independent variables.

Better exam memory and recall are those other variables, and their changes in response to note-taking methodology will be investigated.

To know more about independent variables, visit:

https://brainly.com/question/28871343

#SPJ1

The force of friction oil an airplane in level flight is given by Ff = kv^2, where k is some constant, and v is the speed of the airplane. When the power output from the engines is P0, the plane is able to fly at a speed v0. If the power output of the engines is increased by 100% to 2P0, the airplane will be able to fly at a new speed given by (A) 1.12v0 (B) 1.26v0 (C) 1.41v0 (D) 2.82v0 (E) 8v0

Answers

If the power output of the engines is increased by 100% to 2P0, the airplane will be able to fly at a new speed of 1.26[tex]v_{0}[/tex].

As, P = F v

So, P = kv³

Then, v/v0 = [tex]\sqrt[3]{P/P0}[/tex].

Therefore, after substituting the values, the speed will be 1.26[tex]v_{0}[/tex].

What is power?

In physics, power is the amount of energy transferred or converted per unit of time. In the International System of Units, the unit of power is the watt, which is equivalent to 1 joule per second. In older works, force is sometimes called activity. Power is a scalar quantity.

Power is related to other quantities. For example, the power required to move a ground vehicle is the product of drag, wheel traction, and vehicle speed. The power of a motor is the product of the torque produced by the motor and the angular velocity of the output shaft. Similarly, the power dissipated in an electrical element of a circuit is the product of the current through the element and the voltage across the element.

If the power output of the engines is increased by 100% to 2P0, the airplane will be able to fly at a new speed of 1.26[tex]v_{0}[/tex].

As, P = F v

So, P = kv³

Then, v/v0 = [tex]\sqrt[3]{P/P0}[/tex].

Therefore, after substituting the values, the speed will be 1.26[tex]v_{0}[/tex].

To know more about power, visit:

https://brainly.com/question/1634438

#SPJ4

consider the following two-step process. heat is allowed to flow out of an ideal gas at constant volume so that its pressure drops from 2.2 atm to 1.4 atm. then the gas expands at constant pressure, from a volume of 5.9 l to 9.3 l, where the temperature reaches its original value. (see figure(figure 1)).

Answers

(a) The gas moves from point a to point b in an isochoric process in which the volume stays constant.

The work done when the gas moves from point A to point B is Wab = PV = 0.

The labor involved in getting the gas to boil, Wbc = PV = 1.4. (9.3 - 5.9) L.atm = 4.76 1 L.atm is equal to 101.325 J.

Work completed, ∆W = 101.325 × 4.76 = 482.3 J

Therefore, the process' overall work was a, b, and c.

Wtotal = 0 plus 482.3 J = 482.3 J (Ans) (Ans)

(b) As previously stated, point C is where the gas temperature returns to its initial value.

As a result, in the process ac through b, the gas doesn't undergo any temperature change.

Tfinal = Tinitial

Therefore, internal energy change U = 0.

To know more about Constant volume visit:

https://brainly.in/question/49693981

#SPJ4

In an experiment, a student measured the volume of a substance while the mass was changed. The student measured up to five kilograms. The graph of the data is plotted below.

A volume versus mass graph is shown with mass on the vertical axes from 1 to 10 kilograms and volume on the horizontal axis from 1 to 5 milliliters. A line from the origin through all points and beyond.

Which of the following is an error the student made in creating an accurate graph?

The axes and graph are based only on measured values.
The axes are labeled with the incorrect variables.
The plotted points do not show all data collected.
The title has the incorrect order for the variables.

Answers

The title has the incorrect order for the variables.

The error in the graph is that the title has the incorrect order for the variables. Therefore, option D is correct.

Variables are factors or quantities that can change or be manipulated and have an effect on the outcome of an experiment or the behavior of a system. They are essential in scientific investigations as they allow researchers to study and understand the relationships and dependencies between different factors.

There are two types of variables and that are independent variables and dependent variables. They provide a systematic way to investigate cause-and-effect relationships and understand patterns.

Learn more about variables, here:

https://brainly.com/question/15078630

#SPJ6

An object with charge -q is in motion near a wire that has a current I to the right. At the instant show in the figure, the object is traveling to the right with speed v. Both the wire and the motion of the object are in the plane of the page. Which of the following statements is true about the force on the object due to the current I at the instant shown?
O The force is directed toward the top of the page
O The force is directed toward the bottom of the page.
O The force is directed toward the right.
O There is no force on the object due to the current.

Answers

The correct answer is option A). The force is directed toward the top of the page.

When an object with charge q is moving near a wire with current I, the object will experience a force due to the magnetic field generated by the current in the wire. The direction of this force is determined by the right-hand rule.

According to the right-hand rule, if you point your right thumb in the direction of the current and your fingers in the direction of the motion of the charged object, the force on the object will be in the direction your palm is facing.

Learn more about Force here:

https://brainly.com/question/388851

#SPJ4

Which of the following describes the independent variable?

It is called the respondent variable.
It is plotted on the vertical axis when graphed.
It refers to a quantity changed by the experimenter.
It is something that remains controlled during trials.

Answers

It refers to a quantity changed by the experimenter.

The independent variable is a variable that is manipulated or controlled by the experimenter in an experiment. It is the variable that is thought to affect the dependent variable, which is the variable being measured or observed in the experiment. The independent variable is plotted on the horizontal axis when graphed, and is often referred to as the predictor variable. The respondent variable is not a commonly used term in scientific research.

considering both static and dynamic (time-dependent) situations, which of the figures represents possible configurations for electric field lines?

Answers

A field line is drawn at a location that is perpendicular to the net. Therefore, the tangent to the electric field line at any place coincides with the direction of the electric field there.

What encapsulates the electric field's relative strength?

Each field line has a direction written on it with an arrow, just like gravitational field lines do. This direction indicates the direction of the electric field at all places along the field line. The density of the field lines represents the relative field strength.

How do you show the existence of electric field lines?

Electric field is a vector quantity, hence a vector arrow can be used to depict it. The length of the arrows at any particular position is inversely proportional to the strength of the electric field there, and they all point in that direction.

To know more about electric field lines visit:-

https://brainly.com/question/14438235

#SPJ4

Given the temperature data shown, which of these ecosystems is definitely in the northern hemisphere
answer choices
Daly Waters
Iquitos
Tindouf
These are all in the southern hemisphere

Answers

The ecosystem that is present in the northern hemisphere is Tindouf

Tindouf is the capital of Algeria's Tindouf province, a city close to the borders of Mauritania, Western Sahara, and Morocco which is located in the northern hemisphere. From the chromatogram drawn by Teresa Glass, we concluded that the city of Tindouf, Algeria is a desert biome with very low winter precipitation and high temperatures. This region is of strategic importance. It has an Algerian military base and airport, with regular flights to Algiers and other domestic destinations. Garet Djebilet's settlement is located in his Tindouf municipality near the border with Mauritania. The settlement has an iron mine and an abandoned airport, and is located about 70 kilometers northwest of Awinetbel his Egla.

Learn more about the northern hemisphere in

https://brainly.com/question/13661560

#SPJ4

10. Which of the following statements BEST describes emotional intelligence?
Emotional intelligence is easily assessed.
Emotional intelligence relies on instincts to solve problems.
Emotional intelligence is closely correlated with verbal ability.
Emotional intelligence is the ability to manage personal feelings well and socially more adept.

Answers

The statement: Emotional intelligence is the ability to manage personal feelings well and socially more adept.

a copper bar of length and negligible resistance slides at constant speed along metal rails. the bar is moving through a region in which there is a uniform magnetic field directed out of the page. a voltmeter is connected across a resistor of resistance . the resistor is connected to the metal rails as indicated in the diagram. (a) determine the magnitude of the magnetic force acting on the bar and indicate the direction of this force on the diagram. your answer should be in terms of the given variables and known constants.

Answers

The magnitude of the magnetic force acting on the bar , Fb is calculated to be = ILB.

What do you understand by magnetic force?

Magnetic force is defined as attraction or repulsion that arises between electrically charged particles because of the motion.

Given length , L and negligible resistance

uniform magnetic field, B

a) To determine the magnitude of the magnetic force acting on the bar:

If rod slides down with constant velocity then total force is zero

X direction  Fb - NsinФ

= Fb = NsinФ

Y direction, mg - NcosФ

mg = NcosФ

Now, Fb/mg = sinФ / cosФ

Fb = mg tanФ

But: Fb = I L B sinФ

The magnitude of the magnetic force acting on the bar , Fb = ILB.

To know more about magnetic force, refer

https://brainly.com/question/2279150

#SPJ4

The three bins represent three important properties of stars. Drag the items that we must measure in orrder to determine each property into the appropriate bin. distance orbital period in binary system apparent brightness orbital distance in binary system color or spectral type Luminosity Surface Temperature Mass

Answers

LUMINOSITY, distance, perceived brightness, surface temperature, -color or spectral type, MASS, -orbital period in binary system, -orbital distance in a binary system.

What does mass mean in a definition?

In physics, mass is a quantitative measure of inertia, a basic characteristic of all matter. It is essentially the resistance a body of matter gives to a change in its speed or location as a result of the application of a force.

What is the ideal description of mass?

A measurement of the volume of material that makes up or is contained within a physical body. Newton's laws of motion are based on classical mechanics, which relates an object's mass to the force needed to accelerate it and, consequently, to its inertia.

To know more about Mass visit:

https://brainly.com/question/28221042

#SPJ4

28. A car is traveling east at an unknown initial velocity. Without changing directions, it accelerates at 0.75 m/s²
for a distance of 300 m, increasing its velocity to 30 m/s. What was the initial velocity of the car?


Answers

Answer: 13 m/s.

Explanation: To solve this problem, we need to use the equation for motion with constant acceleration:

d = v₀t + 1/2 at²

where d is the distance traveled, v₀ is the initial velocity, t is the time it takes to travel that distance, and a is the acceleration.

Since we know the distance the car travels (300 m), the final velocity of the car (30 m/s), and the acceleration of the car (0.75 m/s²), we can solve for the initial velocity. We just need to rearrange the equation to solve for v₀:

v₀ = (d - 1/2 at²) / t

In this case, we can plug in the known values to find the initial velocity:

v₀ = (300 - 1/2 * 0.75 * t²) / t

Since the final velocity of the car is 30 m/s and the acceleration is 0.75 m/s², we can use the equation for motion with constant acceleration to find the time it takes for the car to travel 300 m:

v = v₀ + at

30 = v₀ + 0.75t

Rearranging to solve for t, we get:

t = (30 - v₀) / 0.75

Substituting this value for t in the equation for the initial velocity, we get:

v₀ = (300 - 1/2 * 0.75 * ((30 - v₀) / 0.75)²) / ((30 - v₀) / 0.75)

This simplifies to:

v₀ = (300 - 1/2 * 0.75 * (900 - 2v₀) / 0.75) / (30 - v₀)

which simplifies further to:

v₀ = (300 - 675 + v₀) / (30 - v₀)

Solving for v₀, we get:

v₀ = -375 / -29

which simplifies to:

v₀ = 13 m/s

Therefore, the initial velocity of the car is 13 m/s.

2. A diverging lens has a focal length of 2.5 cm. If it is placed 4.0 cm from an object, at what distance from the lens will the image be located? Is the image bigger or smaller? Is it real or virtual?

Answers

The image distance is 0.65 cm and the image is real but diminished.

What is a diverging lens?

We know that for the diverging lens the light appears to be diverged from the source that it come in through. The focal length of the diverging lens is negative and the lens formula is used.

We have;

1/f = 1/u + 1/v

f = focal length

u = object distance

v = image distance

-1/2.5 = 1/4 + 1/v

1/v = 1/4 + 1/2.5

v = 0.25 + 0.4

v = 0.65 cm

The image is real but it is smaller than the object.

Learn more about image distance:https://brainly.com/question/12629638

#SPJ1

A length of wire is connected to a 9.0 V power pack and an ammeter. The reading on the ammeter is 0.25 A.
Calculate the resistance of the wire. Give the unit.

Answers

The resistance of the wire, given that it is connected to a 9.0 V power pack and an ammeter is 36 ohms

How do I determine the resistance?

From Ohm's law, we understood that the voltage, current and resistance are related according to the following formula:

Voltage (V) = Current (I) × resistance (R)

V = IR

Using the above formula, we can obtain the resistance of the wire as follow:

Voltage (V) = 9.0 VoltsCurrent (I) = 0.25 AResistance (R) = ?

Voltage (V) = Current (I) × resistance (R)

9 = 0.25 × resistance

Divide both sides by

Resistance = 9 / 0.25

Resistance = 36 ohms

Thus, we can conclude that the resistance of the wire is 36 ohms

Learn more about resistance:

https://brainly.com/question/23960560

#SPJ1

a projectile with two times the mass is placed into the launcher out with the same initial velocity would this change the range

Answers

Yes, the range would change. Since the mass of the projectile has doubled, its momentum has also doubled.

What is momentum?

Momentum is the measure of an object's resistance to changes in its state of motion. It is a vector quantity, meaning it has both magnitude and direction. Momentum is calculated by multiplying the mass and velocity of an object. Momentum is conserved, meaning that the total momentum of a system remains constant, even if the individual momentum of each object within the system changes. In a collision between two objects, the total momentum before the collision is equal to the total momentum after the collision. Momentum is a powerful concept and has many applications in physics. For example, it is the basis for the laws of motion, the conservation of energy, and the study of planetary motion.

Since momentum is conserved, the projectile's velocity after launch will be reduced. This in turn will reduce the range of the projectile, as it will not be able to travel as far with a lower velocity as it would with a higher velocity.

To learn more about momentum
https://brainly.com/question/18798405
#SPJ4

This range would increase 4 times.

What does the term "projectile motion" refer to?

The movement of an object that has been launched into the air is known as projectile motion. Only gravity is felt by the item after the initial force that launches it. Projectile and trajectory both refer to the same thing: an object.

The projectile's motion is divided into two parts: vertical motion and horizontal motion. Furthermore, since perpendicular components of motion are not reliant on one another, it is necessary to discuss each of these two components of motion independently.

Range of projectile is  R=(vi²sin2∅)/g

So when the velocity is doubled, Range R will be

I.e R'= ((2Vi)²sin2∅)/g

R'=4(Vi²sin2∅)/g

R'=4R

To learn more about projectile motion use link below:

https://brainly.com/question/10680035

#SPJ4

Define the term e.m.f

Answers

EMF is the Electromotive force. It is the electric potential difference which is produced by the cell or the surrounding magnetic field.

What is EMF?

Electromotive force is also known as electromotance or EMF. It is an energy transfer to an electric circuit per unit of the electric charge of the cell or the magnetic field. It is measured in units of volts. Devices which are used to measure electromotive force is called electrical transducers which provide an EMF by converting other forms of energy in the cell into electrical energy.

Other electrical equipment which can also produce an electromotive force, such as the batteries, also convert chemical energy, and generators, the devices which convert mechanical energy. This energy conversion can be achieved through physical forces that are applied physical work on electric charges. However, the electromotive force itself is not a physical force, and for the current ISO/IEC standards that consider the term deprecated, favoring the names which source voltage or source tension instead.

Learn more about EMF here:

https://brainly.com/question/15121836

#SPJ1

A circular loop of wire is positioned half in and half out of a square region of uniform magnetic field directed in the +z direction, out of the paper, as shown in the following figure. To induce a counterclockwise current in this loop

Answers

To induce a counterclockwise current in the circular loop of wire, you can use Faraday's law of electromagnetic induction.

Faraday's law states that the induced electromotive force (emf) in a closed circuit is equal to the negative of the rate of change of the magnetic flux through the circuit.

In this case, the magnetic field is directed out of the paper and is uniform within the square region. As the loop of wire is positioned half in and half out of the square region, the magnetic flux through the loop will change as the loop moves or as the magnetic field strength changes. This change in magnetic flux will induce an emf in the loop, which will cause a current to flow in the wire.

The direction of the current will be determined by Lenz's law, which states that the induced current will be in the direction that opposes the change in magnetic flux. Since the magnetic field is directed out of the paper and the loop is moving counterclockwise, the induced current will flow counterclockwise.

Learn more about Faraday's law here:

https://brainly.com/question/17012638

#SPJ4

In an experiment, a student measured the volume of a substance while the mass was changed. The student measured up to five kilograms. The graph of the data is plotted below.

A volume versus mass graph is shown with mass on the vertical axes from 1 to 10 kilograms and volume on the horizontal axis from 1 to 5 milliliters. A line from the origin through all points and beyond.

Which of the following is an error the student made in creating an accurate graph?

The axes and graph are based only on measured values.
The axes are labeled with the incorrect variables.
The plotted points do not show all data collected.
The title has the incorrect order for the variables.

Answers

Answer:

Answer:

let the first point be a second be b third be c fourth be d and last point be e.

The point a and d are incorrect. because tye plotting of the is incorrect

8. Consider the following equation: IQ (MA/CA) X 100. What does the MA stand for?
m-factor
mental age
male factor
multiple factor

Answers

Answer:

In the equation IQ (MA/CA) X 100, the MA stands for mental age. Intelligence quotient (IQ) is a measure of cognitive ability that is often calculated using the ratio of an individual's mental age to their chronological age, multiplied by 100. In this equation, MA refers to the individual's mental age, which is their level of cognitive development as measured by an intelligence test. CA refers to their chronological age, which is their actual age in years. The ratio of these two values is used to calculate their IQ score.

Other Questions
What did the U.S. want in the Treaty of Versailles? What is scope 1 scope 2 and scope 3? what did gatsby do to impress daisy? question 9 options: he gave her a pearl necklace worth $500,000. he showed her his house and elegant clothes. he took her for a ride in his hydroplane. he showed her the love letters he had written her, but never sent. What is gerrymandering and how does it affect the House of Representatives? an equipment purchased last year is an example of a(n): a. avoidable cost b. differential cost c. sunk cost d. relevant cost At issue in a particular city vote is how much to spend, per person, on city parks next year. Among the 10,000 voters, 1000 prefer to spend $30 per person, but no more; 3500 prefer to spend $45 per person, but no more; 2,500 prefer to spend $80 per person, but no more; and 3000 prefer to spend $150 per person, but no more. INVERSE PROPORTION EXAMPLES When you include the purchase price and the interest, how much does the TV cost you in total? you want to have $5,000 by the time you finish college in 3 years. how much money should you deposit each quarter for the next 3 years into an account paying 8% per year compounded quarterly so that you can have $5,000 when you finish college? a) $368.80 b) $372.80 c) $370.80 d) $369.80 e) $371.80 f) none of the above. What are the elements of realism? Drag the labels onto the diagram to identify the basic structures of the epidermis-dermis junction How do you solve using a graph? s it possible to change velocity while moving at a constant speed?absolutely not because they are of the same value; a speed is just a magnitude of a velocity.yes, if acceleration has component parallel to the velocity but has no component perpendicular to the velocity.yes, if acceleration has component perpendicular to the velocity but has no component parallel to the velocity.no, change is velocity will be always followed by the change in speed. shuffle a standard deck of 52 playing cards. turn over the top card. put the card back in the deck and shuffle again. repeat this process until you get a queen. count the number of cards you had to turn over. which conditions for a binomial setting have been met for this scenario? _____ take(s) the view that capitalist and socialist economic systems, in adopting features of one another, will create a mixed economic system. "Are elephants real?" I asked my dad.He looked quite stunned and shocked."Because if they are, well don't you think,You'd see them in the shops?""It's not like that," dad said to me."They're just not put on sale.""But why?" I said, "They should, you know.And maybe also whales!""They're just not put on sale.""But why?" I said, "They should, you know,And maybe also whales!""I don't understand," my dad confessed."Why you think this should be so."He scratched his head and then his chin,"I don't get it. No...no...no!""Just think of it," I said to dad,They'd be fun to have around!""I could use one just to help me,See the world from off the ground."That's true," dad said, "But you should know.That elephants don't like cities.Oh," I said, "Well that's a shame.That really is a pity."Which word best describes the mood of the poem?seriouspitifulmagical mast company reports net income of $315,000 for the year ended december 31. it also reports $98,900 depreciation expense and a $10,600 loss on the sale of equipment. its comparative balance sheet reveals a $42,600 increase in accounts receivable, a $10,800 decrease in prepaid expenses, a $16,200 increase in accounts payable, and a $13,300 decrease in wages payable. calculate the net increase in cash for the year. A customer contact audit is done by A society is productive inefficient when O a. it produces at a point on its PPF. O b. it does not produce the maximum amount of output with its given resources and technology O c. it can produce more of one good only by giving up some of another good. O d. it produces at a point beyond its PPF Research some professional organizations and agencies related to the healthcare field and examine the roles that each play. List at least one organization related to the diagnostics pathway and one related to the therapeutics pathway, and discuss how healthcare professionals benefit from being members.