an ideal gas expands isothermally (t = 420 k ) from a volume of 2.00 l and a pressure of 9.8 atm to a pressure of 1.0 atm. What is the entropy change for this process?

If a current of 100 mA is passed through a solution of copper sulfate and 30 coulombs of charge pass before copper is deposited on the electrode, then the mass of copper deposited on the electrode 9.89 mg.

To calculate the mass of copper deposited on the electrode, we must apply Faraday's electrolysis equations, which indicate that the quantity of a substance deposited on an electrode during electrolysis is directly proportional to the amount of electricity that flows through the electrolytic cell.

The formula we can use is:

mass = (Q × M) / (n × F)

Where:

Q is the total electric charge passed through the cell (in coulombs)

M is the molar mass of the substance being deposited (in grams per mole)

n is the number of electrons involved in the deposition reaction (this is also the charge on the ion being deposited)

F is Faraday's constant, which is the amount of charge in one mole of electrons (96,485 C/mol)

In this case, we are depositing copper from a copper sulfate solution, and the reaction is:

Cu2+ + 2e- -> Cu

So n is 2 (since 2 electrons are involved) and M is the molar mass of copper, which is 63.55 g/mol.

Plugging in the numbers, we get:

mass = (30 C × 63.55 g/mol) / (2 × 96,485 C/mol)

mass = 9.89 mg

To know more about copper :

https://brainly.com/question/19761029

#SPJ1.

The spoon-shaped projection of the scapula is called the spine of the scapula.

The scapula, also known as the shoulder blade, is a flat, triangular bone located on the upper back, connecting the humerus (upper arm bone) to the clavicle (collarbone). The spine of the scapula is a prominent bony ridge that runs diagonally across the dorsal side of the scapula, this ridge serves as a point of attachment for various muscles that help to stabilize and move the shoulder joint. One of the most important functions of the spine of the scapula is to divide the scapula into two distinct regions, known as the supraspinous fossa and the infraspinous fossa. These fossae accommodate the muscles of the rotator cuff, a group of muscles and tendons that provide stability and mobility to the shoulder joint.

The spine of the scapula also terminates at the acromion process, which forms the highest point of the shoulder and is a key structure in the formation of the acromioclavicular joint. In summary, the spine of the scapula is a critical anatomical structure in the shoulder, providing a point of attachment for various muscles and tendons that contribute to the stability and mobility of the shoulder joint. It also serves as an important landmark for the division of the scapula into distinct functional regions. The spoon-shaped projection of the scapula is called the spine of the scapula.

Learn more about scapula at:

https://brainly.com/question/15041799?

#SPJ11

The magnitude of the momentum of the 29 g sparrow flying with a speed of 6.0 m/s is 0.174 kg m/s.

In Newtonian mechanics, momentum is the product of the mass and velocity of an object. It is a vector quantity, possessing a magnitude and a direction. Momentum is the product of the mass of a particle and its velocity.

To find the magnitude of the momentum of a 29 g sparrow flying with a speed of 6.0 m/s, you need to use the formula for momentum:
momentum = mass × velocity

First, convert the mass of the sparrow from grams to kilograms:
29 g = 0.029 kg

Next, plug in the values for mass and velocity into the formula:
momentum = 0.029 kg × 6.0 m/s

Now, calculate the momentum:
momentum = 0.174 kg m/s

Learn more about momentum:

https://brainly.com/question/1042017

#SPJ11

The change in magnetic potential energy of a loop from its original position to a new angled position depends on the orientation of the magnetic field, the current flowing through the loop, and the angle between the loop and the field. When the angle between the loop and the magnetic field changes, the magnetic flux through the loop also changes, which results in a change in the magnetic potential energy of the loop.


The magnetic potential energy of a loop is given by the formula U = -m*B*cos(theta), where U is the magnetic potential energy, m is the magnetic moment of the loop, B is the magnetic field strength, and theta is the angle between the magnetic moment and the field. When the angle changes from the original position to a new angled position, the value of cos(theta) changes, which results in a change in the magnetic potential energy of the loop.

In general, the magnetic potential energy of a loop will increase when the angle between the loop and the magnetic field decreases, and it will decrease when the angle increases. The amount of change in magnetic potential energy will depend on the magnitude of the angle change and the strength of the magnetic field.

In conclusion, the change in magnetic potential energy of a loop from its original position to a new angled position can be calculated using the formula U = -m*B*cos(theta), where the angle theta is the difference between the original and new positions. This change in energy can be positive or negative, depending on the direction of the angle change and the orientation of the magnetic field.

Learn more about flux here:

https://brainly.com/question/14527109

#SPJ11

Okay, let's break this down step-by-step:

1) Aircraft speed = 900 km/h = 250 m/s

2) Altitude = 10,000 m

3) When directly overhead:

- Angular velocity = (Velocity) / (Distance) = (250 m/s) / (10,000 m altitude) = 0.025 rad/s

4) 3 minutes later:

- Aircraft will have moved 10,000 * (3/60) = 500 m away from your position

- New distance from you = 10,500 m

- New angular velocity = (250 m/s) / (10,500 m) = 0.024 rad/s

So in summary:

- When directly overhead: Angular velocity = 0.025 rad/s

- 3 minutes later: Angular velocity = 0.024 rad/s

Let me know if you have any other questions!

Okay, let's break this down step-by-step:

1) Aircraft speed = 900 km/h = 250 m/s

2) Altitude = 10,000 m

3) When directly overhead:

- Angular velocity = (Velocity) / (Distance) = (250 m/s) / (10,000 m altitude) = 0.025 rad/s

4) 3 minutes later:

- Aircraft will have moved 10,000 * (3/60) = 500 m away from your position

- New distance from you = 10,500 m

- New angular velocity = (250 m/s) / (10,500 m) = 0.024 rad/s

So in summary:

- When directly overhead: Angular velocity = 0.025 rad/s

- 3 minutes later: Angular velocity = 0.024 rad/s

Let me know if you have any other questions!

Answer:

7.7 × 10^-10 N

Explanation:

To calculate the magnetic force on the airplane, we need to use the formula:

F = qvBsinθ

where:

F = magnetic force

q = net charge

v = velocity of the airplane

B = strength of the magnetic field

θ = angle between the velocity and magnetic field

In this case, the net charge is given as 1540 μc, which we can convert to Coulombs:

q = 1540 μC = 1.54 × 10^-6 C

The velocity of the airplane is given as 100 m/s, and the strength of the Earth's magnetic field is 5.0 × 10^-5 T. However, we also need to know the angle between the velocity and magnetic field. If the airplane is moving perpendicular to the magnetic field, then θ = 90°, which means that sinθ = 1.

Now we can plug in the values and calculate the magnetic force:

F = qvBsinθ

F = (1.54 × 10^-6 C)(100 m/s)(5.0 × 10^-5 T)(1)

F = 7.7 × 10^-10 N

Therefore, the magnetic force on the airplane is 7.7 × 10^-10 N.

*IG:whis.sama_ent

Answer:

Star trails reflect Earth's rotation, or spin, around its axis. The Earth makes a complete rotation relative to the backdrop stars in a period of about 23 hours and 56 minutes.

The inertia dyadic is  (50 * a^2 * t/12) * [1 0 0; 0 1 0; 0 0 2].

The inertia dyadic about the mass center for the thin plate with a square void centered at the center of the plate can be calculated using the formula

I = ∫(r^2 * dm),

where r is the distance from the axis of rotation to the mass element dm.

Since the plate is thin, we can assume that it has a constant thickness and therefore, its mass can be expressed as

M = ρ * A * t,

where ρ is the density, A is the area of the plate, and t is the thickness of the plate.

The mass center of the plate is located at the geometrical center of the plate, which is also the center of the square void. Therefore, the distance from the mass center to any point on the plate is half the length of the diagonal of the square void, which is

d = √2 * a/2, where a is the side length of the square void.

Using these values, the inertia dyadic about the mass center can be expressed as

I = (M/12) * [a^2 + (d^2/2)] * [1 0 0; 0 1 0; 0 0 2],

where [1 0 0; 0 1 0; 0 0 2] is the inertia tensor for a thin plate with a uniform density, and the factor of 1/12 is due to the parallel axis theorem.

Substituting the given values, we get I = (50 * a^2 * t/12) * [1 0 0; 0 1 0; 0 0 2], where a is the side length of the square void and t is the thickness of the plate.

To learn more about "inertia", visit: https://brainly.com/question/1140505

#SPJ11

(a)The capacitance of the circuit is 2.00 × 10⁻⁴F. (b) The charge on the capacitor when it is fully charged is 1.50 × 10⁻³C.

(a) The time constant of the RC circuit can be calculated using the time when the voltage is at (0.63Vmax):

τ = RC = t(0.63Vmax) = 0.080 s - 0.040 s = 0.040 s

Given the equivalent resistance of the circuit, R = 200.0 Ω, we can solve for the capacitance:

C = τ/R = (0.040 s)/(200.0 Ω) = 2.00 × 10⁻⁴F

Therefore, the capacitance of the circuit would be 2.00 × 10⁻⁴F.

(b) The charge on a fully charged capacitor is given by:

Q = CVmax

Already know the capacitance, C, and the maximum voltage, Vmax, which is simply the voltage when the capacitor is fully charged. From the given data, can see that Vmax is 7.50 V. Therefore, we have:

Q = (2.00 × 10⁻⁴F)(7.50 V) = 1.50 × 10⁻³C

Therefore, the charge on the capacitor when it is fully charged would be 1.50 × 10⁻³C.

To know more about capacitance

https://brainly.com/question/4294800

#SPJ4

The flywheel's tip rotates through four revolutions in around 0.628 seconds.

If a flywheel has a 1 m diameter and rotates at 1200 rpm, the acceleration at that point is. 8π2 m/s2

The time needed for a specific number of rotations of the flywheel can be calculated using the method for converting linear velocity to angular velocity:

ω = v / r

where r is the flywheel's radius in feet, is the angular velocity expressed in radians per second, and v is the linear velocity expressed in feet per second.

In this instance, v = 30.0 ft/s and r = 1.50 ft, respectively, so

The formula is = v / r = 30.0 ft/s / 1.50 ft = 20.0 rad/s.

Using the formula, we can calculate how long it takes the flywheel to complete 4 radians.

θ = ω t

When the angle is expressed in radians, the angular speed is expressed in radians per second, and the duration is expressed in seconds.

Here, we wish to determine t when = 4, so

4π = 20.0 rad/s * t

As we solve for t, we obtain

t = (4 rad) / (20.0 rad/s) = 0.628 seconds

To know more about flywheel visit:

https://brainly.com/question/18883102

#SPJ1

Answer: Velocity increase is, 5m/s.

Explanation: Given,

t = 25s, acceleration(a)=0.2m/s², assuming(required but not given) initial velocity = 0m/s.

According to laws of motion,

v = u + at,

v : Final velocity

u : Initial velocity

a : Acceleration

t : Time

Therefore, on putting values, as given, we get

v = 0 + (0.2)(25)

v = 5m/s

Therefore, velocity increase is 5m/s.

Read more about Velocity:

https://brainly.com/question/25905661

The given statement " the magnitude of heat and work done on a process depends only on the initial and final state of the process" is True .

The magnitude of heat or work done on a process is independent of the path taken between the initial and final states, and depends only on the state of the system at the beginning and end of the process. This is known as the first law of thermodynamics.
This statement is true for a specific type of process known as a path-independent process, such as an isothermal or adiabatic process. In these cases, the amount of heat and work done is determined solely by the difference between the initial and final states, and not by the specific path taken to reach those states.

Hence, the given statement is True, the magnitude of heat and work done on a process depends only on the initial and final state of the process.

To know more about Heat refer here :

https://brainly.com/question/934320

#SPJ11

(a) If the speed of the moving object is doubled, its kinetic energy will become four times greater.

(b) If the mass of the moving object is doubled, its kinetic energy will also become twice as much.

a) This is because kinetic energy is directly proportional to the square of the velocity, as shown in the equation KE = 1/2mv². Therefore, doubling the speed will result in a kinetic energy of 400 J.

b) This is because kinetic energy is directly proportional to the mass, as shown in the equation KE = 1/2mv². Therefore, doubling the mass will result in a kinetic energy of 200 J.

Kinetic energy is the energy that an object possesses due to its motion. It is calculated using the formula KE = 1/2mv², where m is the mass of the object and v is its velocity. This formula shows that kinetic energy is directly proportional to the mass and the square of the velocity of the object.

This means that any change in mass or velocity will have a direct effect on the object's kinetic energy. When the speed is doubled, the kinetic energy becomes four times greater because velocity is squared in the formula.

When the mass is doubled, the kinetic energy becomes twice as much because mass is directly proportional to kinetic energy.

To know more about kinetic energy click on below link:

https://brainly.com/question/999862#

#SPJ11

The activation energy of a certain reaction is used to find the temperature at which the reaction would go twice as fast.  while the Arrhenius equation can be used to find the rate constant at a different temperature for the same reaction.

We can use the Arrhenius equation, which relates the rate constant of a reaction to the activation energy and temperature. We know the rate constant at 20C and the activation energy, so we can set up the equation as follows:

k2 = 2k1
ln(k2/k1) = Ea/R * (1/T1 - 1/T2)
T2 = Ea/R * (1/T1 - ln(k2/k1)/Ea)

Plugging in the given values, we get:

T2 = 47.1 kJ/mol / (8.314 J/mol*K) * (1/293 K - ln(2)/(47.1 kJ/mol))
T2 ≈ 358 K or 85 C

For the second part of your question, we can use the same equation to find the rate constant at 140 C:

ln(k2/k1) = Ea/R * (1/T1 - 1/T2)
k2 = k1 * e^(Ea/R * (1/T1 - 1/T2))

Plugging in the given values, we get:

k2 = 0.0170 s^-1 * e^(47.1 kJ/mol / (8.314 J/mol*K) * (1/293 K - 1/413 K))
k2 ≈ 1.81 s^-1.

To know more about Arrhenius equation refer here:

https://brainly.com/question/21148211#

#SPJ11

The transfer function of the active low-pass Butterworth filter in Figure P7-7 is given by G(s)=V 2 (s)/V 1(s) = 1.5858/(1 + (1/ωc)s).

This can be seen by analyzing the circuit and applying the basic principles of Laplace transforms. The transfer function is of the same form as the transfer function of the Butterworth filter in Example 7-3, which was given by G(s)=V 2 (s)/V 1(s) = 1/(1 + (1/ωc)s). The only difference is in the numerator constant.

In Figure P7-7, the numerator constant is 1.5858 due to the gain of 1.5858 of the VCVS. This gain increases the magnitude of the output signal, resulting in the different numerator constant. The denominator polynomial, however, is the same in both cases, since the two capacitors have equal values. Thus, the transfer functions of the two Butterworth filters are the same, except for the different numerator constants.

Know more about Laplace transforms here

https://brainly.com/question/1597221#

#SPJ11

In a dream, you're in a car traveling at 50 km/h and you bump into another car traveling toward you at 48 km/h. the speed of impact is 98 km/h.

To calculate the speed of impact in your dream, where your car is traveling at 50 km/h and the other car is traveling towards you at 48 km/h, you simply add the speeds of both cars. The speed of impact in this scenario would be 50 km/h (your car) + 48 km/h (the other car) = 98 km/h. An impact velocity is the total speed of an object when it makes an impact with the ground or another object after falling from a certain distance. How do you find the impact speed of two cars? Once the momentum of the individual cars is known, the after-collision velocity is determined by simply dividing momentum by mass (v=p/m).

Learn more about the speed of impact here: https://brainly.com/question/27918228

#SPJ11

Answer:

The work done is 375×10²J or 37500J

Explanation:

W=F×d

W=F×s

W=7.5×10³×5

W=75×10²×5

W=375×10²J

We can express the angle in degrees by converting from radians to degrees:
θa(ii) = θa(ii) * (180 / π)

To find the direction angle θa(ii) of the velocity of sphere A after the first collision, we'll need information about the initial velocities and masses of the spheres involved in the collision, as well as their relative positions.

Once we have that information, we can use conservation of momentum and energy principles to find the final velocities of the spheres. Then, we can calculate the direction angle θa(ii) by taking the inverse tangent (arctan) of the ratio of the y-component of the velocity to the x-component of the velocity:

θa(ii) = arctan(Vy / Vx)

Finally, we can express the angle in degrees by converting from radians to degrees:

θa(ii) = θa(ii) * (180 / π)

Please provide the necessary information, and I will be glad to help you find the direction angle θa(ii) for the velocity of sphere A after the first collision.

To learn more about velocity, refer below:

https://brainly.com/question/17127206

#SPJ11

The force exerted by the spring using Hooke's Law, states that the force exerted by a spring is directly proportional to the amount it is stretched from its equilibrium position.

So, F = kx,

where F is the force exerted by the spring, k is the spring constant, and x is the displacement of the spring from its equilibrium position.

In this case, the spring is stretched by 22.0 cm, which is 0.22 m. So, F = (95.0 N/m) x (0.22 m) = 20.9 N.

Next, we can use Newton's second law of motion, which states that the acceleration of an object is directly proportional to the net force acting on it and inversely proportional to its mass. So,

a = F/m,

where a is the acceleration of the object and m is its mass.

In this case, the net force acting on the object is the force exerted by the spring, which is 20.9 N. The mass of the object is 9.00 kg. So, a = (20.9 N) / (9.00 kg) = 2.32 m/s^2.

Therefore, the magnitude of the acceleration of the object is 2.32 m/s^2.

To know more about Force visit:

https://brainly.com/question/13191643

#SPJ11

The amount of energy required to change a 39 g ice cube from ice at -12°C to steam at 112°C is 1.032 x 108 J.

Given

The specific heat of ice is 2090 J/kg °C

The specific heat of water is 4186 J/kg °C

The specific heat of stream is 2010 J/kg C

The heat of fusion is 3.33 x 105 J/kg

The heat of vaporiza- tion is 2.26 x 106 J/kg

To Find

ice cube=39g

temperature= -12 °C to  at 112 °C

Solution

To solve this problem, we need to break down the process into different steps and calculate the amount of energy required for each step.

Step 1: Heating the ice from -12°C to 0°C

Energy required = mass of ice x specific heat of ice x change in temperature

Energy required = 39 g x 2090 J/kg °C x (0°C - (-12°C))

Energy required = 980,280 J

Step 2: Melting the ice at 0°C to water at 0°C

Energy required equals mass of ice multiplied by heat of fusion

Energy required = 39 g x 3.33 x 105 J/kg

Energy required = 1.299 x 107 J

Step 3: Heating the water from 0°C to 100°C

Energy required = mass of water x specific heat of water x temperature change

Energy required = 39 g x 4186 J/kg °C x (100°C - 0°C)

Energy required = 1.629 x 106 J

Step 4: Boiling the water at 100°C to steam at 100°C

Energy required = mass of water x heat of vaporization

Energy required = 39 g x 2.26 x 106 J/kg

Energy required = 8.814 x 107 J

Step 5: Heating the steam from 100°C to 112°C

Energy required = mass of steam x specific heat of steam x change in temperature

Energy required = 39 g x 2010 J/kg °C x (112°C - 100°C)

Energy required = 9.354 x 105 J

Total energy required = Energy for Step 1 + Energy for Step 2 + Energy for Step 3 + Energy for Step 4 + Energy for Step 5

Total energy required = 980,280 J + 1.299 x 107 J + 1.629 x 106 J + 8.814 x 107 J + 9.354 x 105 J

Total energy required = 1.032 x 108 J

Therefore, the amount of energy required to change a 39 g ice cube from ice at -12°C to steam at 112°C is 1.032 x 108 J.

To know more about Latent heat of fusion follow

brainly.com/question/87248

The electric potential at the center of the semicircle is V = (λ/2ε₀).

To find the electric potential at the center of the semicircle, you need to consider the following terms:

λ (linear charge density), r (radius of the semicircle), ε₀ (vacuum permittivity), and π (pi).

To calculate the electric potential at the center of the semicircle, follow these steps:

1. Divide the semicircle into small segments with length Δs, each carrying a small charge Δq = λΔs.
2. The electric potential at the center due to each small charge Δq can be found using the formula:

ΔV = kΔq/r, where k = 1/4πε₀ is the electrostatic constant.
3. Integrate ΔV over the entire semicircle to find the total electric potential at the center.

The integration gives you the total electric potential at the center of the semicircle as:

[tex]V = (\lambda/2\pi \epsilon_0) \int(d\theta)[/tex] from 0 to π, where dθ is the angle subtended by Δs at the center.

Upon integrating and substituting the limits, you get:
V = (λ/2πε₀) * π

So, the electric potential at the center of the semicircle is:
V = (λ/2ε₀).

Learn more about a semicircle:

https://brainly.com/question/15822332

#SPJ11

Lift is directly proportional to airspeed when angle of attack (AOA) and altitude are held constant, according to the lift equation: Lift ∝ Airspeed.

The lift equation states that lift is directly proportional to the square of airspeed, all else being constant. This means that as airspeed increases, lift will also increase, assuming the angle of attack (AOA) and altitude remain constant.

This relationship is due to the increase in the dynamic pressure of the air on the wings as the aircraft moves through the air at higher speeds. Higher airspeed results in greater air pressure difference between the upper and lower surfaces of the wings, leading to increased lift.

This relationship is important in aviation, as pilots need to carefully manage airspeed to control lift during different phases of flight, such as takeoff, cruise, and landing.

For more questions like Constant click the link below:

https://brainly.com/question/14977272

#SPJ11

The magnetic force exerted on the 2.15 m length of wire carrying a current of 0.914 A perpendicular to a magnetic field of 0.730 T is approximately 1.43163 N.

The magnetic force exerted on a wire carrying a current perpendicular to a magnetic field can be calculated using the formula:

F = B * I * L

where F is the magnetic force, B is the magnetic field strength (0.730 T), I is the current (0.914 A), and L is the length of the wire (2.15 m).

F = 0.730 T * 0.914 A * 2.15 m = 1.43163 N

Therefore, the magnetic force exerted on the 2.15 m length of wire carrying a current of 0.914 A perpendicular to a magnetic field of 0.730 T is approximately 1.43163 N.

Know more about Magnetic Force here:

https://brainly.com/question/22358314

#SPJ11

The 200 g ball lands at a distance of 2.0 m from the base of the table.

We are given the masses of the balls (100 g and 200 g), the distance from the base of the table (2.0 m), and we need to determine the distance the 200 g ball lands from the base of the table.

To solve this problem, we'll assume that the only force acting on the balls after they leave the table is gravity, and that air resistance is negligible.

Since both balls roll off the table with the same speed and are only affected by gravity, their horizontal motion should be the same.

Recognize that both balls have the same initial horizontal speed and are under the influence of gravity.

Understand that their masses (100 g and 200 g) do not affect their horizontal motion because gravity affects all objects equally.

Since their horizontal motion is the same, the 200 g ball will also land 2.0 m from the base of the table, just like the 100 g ball.

Learn more about distance:

https://brainly.com/question/26550516

#SPJ11

The Decay of silicon-27 by positron emission yields aluminum-27, a positron, and a neutrino.

When silicon-27 decays by positron emission, it yields the following:

1. Silicon-27 (Si-27) undergoes positron emission, which is a type of radioactive decay.

2. During positron emission, a proton in the nucleus of Si-27 is converted into a neutron.

3. This process creates a positron (a positively charged electron) and a neutrino, which are emitted from the nucleus.

4. As a result of this decay, the atomic number of the element decreases by one, and the mass number remains the same.

5. The new element formed is aluminum-27 (Al-27).

For more questions on Decay, click on:

https://brainly.com/question/2053871

#SPJ11

Answer:

Both beauty standards and the feminine beauty ideal are moving targets. Psychologists have argued that it may be all but impossible to separate what we inherently and individually find beautiful from what society tells us is beautiful. In my opinion, beauty standards are the gnarled and rotten roots of all that’s wrong with the industry and perhaps the world. They are tools of oppression that reinforce sexism, racism, colorism, classism, ableism, ageism, and gender norms. They are built into our societies and embedded into our brains.

According to scientists' recent research, women are well represented in media and entertainment companies. But even with corporate America’s increased focus on ensuring gender parity. Scientist observed that women’s day-to-day workplace experiences in media and entertainment are worse than men’s. Almost half of all respondents said they believe women in their fields are judged by different standards than men, which they say makes it difficult to achieve parity in senior management in their workplaces. So the media influence on pre-teens and teenagers can be deliberate and direct. For example, advertising is often directed at children of all ages. This means that children, pre-teens and teenagers are increasingly conscious of brands and images.

The EM wave has a frequency of roughly 4.23 x 10¹⁴ Hz. This EM wave would be categorised as visible light, more especially in the red region of the spectrum, based on its frequency.

To calculate the frequency, divide the total number of occurrences of the event by the duration. Example: Anna divides the time by the quantity of page clicks (236). (one hour, or 60 minutes). Her clickthrough rate is 3.9 per minute, she learns. This gives the wave's frequency in Hertz as well.

c = fλ

Since the wave is in free space, its speed is the speed of light in vacuum, which is approximately 3.00 x 10⁸ m/s.

We need to convert the wavelength to meters, which gives: λ = 710 nm x (1 m/10⁹ nm) = 7.10 x 10⁻⁷ m.

f = c/λ = (3.00 x 10⁸ m/s)/(7.10 x 10⁻⁷ m) ≈⁸ 4.23 x 10¹⁴ Hz.

Therefore, the frequency of the EM wave is approximately 4.23 x 10¹⁴ Hz.

To know more about frequency visit:-

https://brainly.com/question/2140860

#SPJ1

Answer:

T = 43,451.16°c

Explanation:

decrease in length = alpha ×original length × change in temperature

31m - 0.04m = 30.96m

30.96m = 2.3 ×10^-5 k^-1 × 31m × ( T - 302k), T temperature final

30.96m = 7.13 ×10^-4 × ( T - 302k)

T - 302k = 30.96m / 7.13 ×10^ -4 m/k

T - 302k = 43,422.16k

T = 43,724.16 k

T = 43,451.16°c

If the two waves have the same amplitude and frequency and produce a resultant disturbance of the same amplitude, they must differ in phase by 90 degrees.

If two waves of the same frequency and amplitude combine, the resulting wave will have an amplitude equal to the sum of the two individual waves.

The phase difference between the two waves will determine the shape of the resulting wave. If the two waves are in phase, meaning their peaks and troughs line up, the resulting wave will have a larger amplitude

If the two waves are out of phase by 180 degrees, meaning their peaks line up with each other's troughs, they will cancel each other out and the resulting wave will have zero amplitude.

Learn more about resultant wave is athttps://brainly.com/question/1832380

#SPJ11

The period of the asteroid in terms of earth years would be approximately 18.25 years. This is calculated by taking the period of the Earth's orbit around the Sun (1 year) and multiplying it by 4.5.

Earth is the third planet from the Sun and the only object in the universe known to harbor life. It is the fifth largest planet in the Solar System and is the densest and most massive of the terrestrial planets. Earth is composed of numerous physical and chemical components, including an atmosphere and hydrosphere which help to regulate its climate and weather patterns.  It also has numerous ecosystems, with millions of species of plants and animals that depend on each other for survival. Earth's lithosphere is composed of numerous tectonic plates that move and interact, creating earthquakes and volcanoes.

To learn more about earth

https://brainly.com/question/27943482

#SPJ1