The mass per kilometer of the aluminum wire such that the resistance of the wire is 0.0360 Ω/km is 21,15 kg/km.
To find the mass per kilometer of the aluminum power transmission line, we need to follow these steps:
1. Calculate the cross-sectional area (A) of the wire using the resistance formula:
R = ρL/A, where R is resistance, ρ is resistivity, L is length, and A is the cross-sectional area.
We need to find the resistivity of aluminum first, which is approximately 2.82 × 10^(-8) Ωm.
2. Rearrange the formula to solve for A: A = ρL/R.
3. Substitute the given values and solve for A:
A = (2.82 × 10⁻⁸ Ωm) × (1000 m) / (0.0360 Ω)
A = 7.83 × 10⁻⁴ m²
4. Calculate the volume per kilometer (V) by multiplying the cross-sectional area (A) by the length (L): V = A × L.
5. Substitute the values and solve for V:
V = (7.83 × 10⁻⁴ m²) × (1000 m)
V = 0.783 m³
6. Finally, calculate the mass per kilometer (M) by multiplying the volume (V) by the density (ρ) of aluminum: M = V × ρ.
7. Substitute the values and solve for M:
M = (0.783 m³) × (2.7 × 10³ kg/m³)
M = 21,15 kg/km
So, the mass per kilometer of the aluminum power transmission line is approximately 21,15 kg/km.
Learn more about resistivity:
https://brainly.com/question/13735984
#SPJ11
A 12.0-\mu F12.0−μF capacitor is charged to a potential of 50.0 V and then discharged through a 225-\Omega225−Ω resistor. How long does it take the capacitor to lose (a) half of its charge and (b) half of its stored energy
(a) It takes approximately 1.91 seconds for the capacitor to lose half of its charge.
(b) It takes approximately 1.91 seconds for the capacitor to lose half of its charge and half of its stored energy.
(a) To find the time it takes for the capacitor to lose half of its charge, we can use the formula Q(t) = Q₀ * [tex]e^(^\frac{t}{^R^C} ^)[/tex], where Q₀ is the initial charge on the capacitor, R is the resistance, C is the capacitance, and t is the time. We want to solve for t when Q(t) = Q₀/2.
Substituting the given values, we have
6.00 × 10⁻⁵ C
= 1/2 * 1.2 × 10⁻⁵ C *[tex]e^(^\frac{-t}{225} ^*^1^.^2^*^1^0^-^5[/tex]).
Simplifying, we get [tex]e^(^\frac{t}{^R^C} ^)[/tex]= 0.5, which gives t = 1.91 s.
(b) The energy stored in a capacitor is given by the formula U = 1/2 * C * V², where U is the energy, C is the capacitance, and V is the potential difference across the capacitor. To find the time it takes for the capacitor to lose half of its stored energy, we need to determine the potential difference across the capacitor when it has lost half of its energy.
Since the energy stored in a capacitor is proportional to the square of the potential difference, the potential difference across the capacitor when it has lost half of its energy is equal to (1/sqrt(2)) * 50.0 V = 35.4 V. We can then use the same formula as in part (a) with V = 35.4 V to find the time it takes for the capacitor to discharge to this potential.
Substituting the given values, we have
0.5 * 1.2 × 10⁻⁵ F * (35.4 V)²
= 1/2 * 1.2 × 10⁻⁵ C * (35.4 V)
= 2.12 × 10⁻⁴ C,
which gives [tex]e^(^\frac{t}{^R^C} ^)[/tex] = 0.5.
Solving for t, we get t = 1.91 s, which is the same as the time it takes for the capacitor to lose half of its charge.
To know more about potential difference click on below link:
https://brainly.com/question/12198573#
#SPJ11
A transformer has two sets of coils, the primary with N1 = 110 turns and the secondary with N2 = 1650 turns. The input rms voltage (over the primary coil) is ΔV1rms = 34 V. Randomized VariablesN1 = 110 N2 = 1650 ΔV1rms = 34 V a) Express the output rms voltage, ΔV2rms, in terms of N1, N2, and ΔV1rms. b) Calculate the numerical value of ΔV2rms in V.
a) The output RMS voltage, ΔV2rms, in a transformer is given by the ratio of the number of turns in the secondary coil to the number of turns in the primary coil, multiplied by the input RMS voltage[tex]ΔV2rms = N2/N1 x ΔV1rms[/tex].
b) Plugging in the values, [tex]ΔV2rms = 1650/110 x 34V = 510V[/tex].
A transformer is a device that is used to change the voltage of an alternating current (AC) by electromagnetic induction. It consists of two sets of coils, the primary and the secondary, which are wound around a common magnetic core. The voltage ratio of the transformer is given by the ratio of the number of turns in the secondary coil to the number of turns in the primary coil. If the input RMS voltage over the primary coil is given, the output RMS voltage over the secondary coil can be calculated using the voltage ratio. In this case, the output RMS voltage, ΔV2rms, is given by [tex]ΔV2rms = N2/N1 x ΔV1rms[/tex], where N1 is the number of turns in the primary coil, N2 is the number of turns in the secondary coil, and ΔV1rms is the input RMS voltage. Plugging in the given values, the numerical value of ΔV2rms is 510V.
Learn more about RMS voltage here:
https://brainly.com/question/28563538
#SPJ11
differentiate between two types of waves?
both segments of the wire are made of the same metal. current i1 flows into segment 1 from the left. how does current density j1 in segment 1 compare to current density j2 in segment 2?
To compare current density J1 in segment 1 to current density J2 in segment 2, you need to determine the cross-sectional areas of both segments and then apply the formula for current density. The relationship between J1 and J2 will depend on the difference in cross-sectional areas of the segments.
To compare the current density (J1) in segment 1 to the current density (J2) in segment 2 when both segments of the wire are made of the same metal and current I1 flows into segment 1 from the left, follow these steps:
1. Understand that current density (J) is defined as the amount of current (I) flowing through a unit cross-sectional area (A) of a conductor, and it is given by the formula J = I / A.
2. Since both segments of the wire are made of the same metal, their electrical properties (such as resistivity) are the same.
3. Observe the cross-sectional areas (A1 and A2) of both segments. If the segments have the same cross-sectional area, then A1 = A2. If one segment has a larger cross-sectional area than the other, note the difference.
4. To compare the current densities, divide the current (I1) by the respective cross-sectional areas (A1 and A2) of each segment:
J1 = I1 / A1
J2 = I1 / A2
5. Compare J1 and J2 to determine their relationship. If A1 = A2, then J1 = J2. If A1 > A2, then J1 < J2. If A1 < A2, then J1 > J2.
To know more about "Density" refer here:
https://brainly.com/question/17226757?#
#SPJ11
At the 5% significance level, what is the conclusion to the test? H0, we conclude that the mean buggies/hour differ for some production lines.
It appears that a test was conducted to compare the mean buggies produced per hour on different production lines. The significance level chosen for the test was 5%.
At the 5% significance level, if the test results show a p-value less than 0.05, we reject the null hypothesis (H0) and conclude that the mean buggies per hour differ for some production lines. If the p-value is greater than or equal to 0.05, we fail to reject the null hypothesis and cannot conclude that there is a significant difference in the mean buggies per hour among production lines.
The conclusion of the test is that there is evidence to suggest that the mean buggies/hour differ for some production lines. This conclusion is based on the rejection of the null hypothesis (H0) that there is no difference in the mean buggies/hour between production lines.
learn more about production lines here: brainly.com/question/16755022
#SPJ11
A car battery has a voltage of ε = 12 V. To turn the starter on a car the battery must supply I = 274 A. It takes t = 4.9 s for the engine to start.
How much energy did the starter consume, E, in J?
The starter consumed approximately 16,105.2 joules of energy during the engine start.
Energy is defined as the capacity to produce a force that results in the displacement of an object. Even though the definition is unclear, the meaning is clear energy is simply the force that moves things.
To find the energy consumed by the starter, we can use the formula:
E = P x t
where P is the power in watts and t is the time in seconds. To find the power, we can use the formula:
P = V x I
where V is the voltage in volts and I is the current in amperes. Plugging in the given values, we get:
P = 12 V x 274 A = 3,288 W
Now we can calculate the energy consumed:
E = 3,288 W x 4.9 s = 16,105.2 J
Therefore, the starter consumed 16,105.2 joules of energy.
To know more about Energy refer here :
https://brainly.com/question/30532156
#SPJ11
In an RCL circuit a second capacitor is added in parallel to the capacitor already present. Does the resonant frequency of the circuit increase, decrease, or remain the same?
1.
The resonant frequency increases, because it is directly proportional to the capacitance, and the equivalent capacitance increases when a second capacitor is added in parallel.
2.
The resonant frequency decreases, because it is directly proportional to the capacitance, and the equivalent capacitance decreases when a second capacitor is added in parallel.
In an RCL circuit, when a second capacitor is added in parallel to the capacitor already present, the resonant frequency decreases. This is because the resonant frequency is inversely proportional to the square root of the capacitance, and the equivalent capacitance increases when a second capacitor is added in parallel. So, the correct answer is option 2.
If the Resistor (R), Inductor (L), and Capacitor (C) are all connected in parallel with the AC current source, then we can say that circuit is a parallel RLC circuit. In this circuit, the voltage across each network element is the same, but only the supply current (AC) will get divided among the passive elements. Therefore the resonant frequency decreases because it is directly proportional to the capacitance, and the equivalent capacitance decreases when a second capacitor is added in parallel.
Learn more about resonant frequency: https://brainly.com/question/28381706
#SPJ11
A thin partition divides a container of volume V into two parts. One side contains na moles of gas Ain a fraction fA of the container; that is, VA = fAV. The other side contains ng moles of a different gas B at the same temperature in a fraction fo of the container. The partition is removed, allowing the gases to mix. Find an expression for the change of entropy. This is called the entropy of mixing. Express your answer in terms of some or all of the variables na, fa, np, fb, and constant R.
The entropy change is positive and proportional to the number of moles of gas and the natural logarithm of 2 and the entropy of mixing is given by ΔS = -R(nAfa ln fa + nBfb ln fb).
How can the change in entropy be calculated when a partition is removed and two gases mix?The change in entropy when the partition is removed and the gases mix can be calculated using the formula:
ΔS = -R[na(fA ln fA + (1-fA) ln (1-fA)) + ng(fB ln fB + (1-fB) ln (1-fB))]
where R is the gas constant, na and ng are the number of moles of gases A and B, respectively, and fA and fB are the fractions of the container that they occupy before mixing.
The formula for entropy change is based on the idea that the number of ways in which the molecules can be arranged in the combined volume is greater than the number of ways in which they could be arranged if they were separated into two volumes. This increase in the number of possible microstates leads to an increase in entropy.
The first term in the equation represents the contribution of gas A to the entropy change, while the second term represents the contribution of gas B. The logarithmic terms arise from the fact that the number of microstates is proportional to the natural logarithm of the number of ways in which the molecules can be arranged.
In the case where the two gases are identical (i.e., na = ng and fA = fB), the entropy change simplifies to:
ΔS = R[na ln 2]
This result shows that the entropy change is positive and proportional to the number of moles of gas and the natural logarithm of 2.
Learn more about change in entropy
brainly.com/question/30691597
#SPJ11
Question 10 1 pts The oxidative energy system typically requires exercise times of O > 2 min O > 3 min > 4 min O > 1 min
It is responsible for producing energy through the use of oxygen in the body. The oxidative energy system typically requires exercise times of over 2 minutes.
The oxidative energy system typically requires exercise times?
The oxidative energy system typically requires exercise times of over 2 minutes, and is responsible for producing energy through the use of oxygen in the body.
This system is characterized by the breakdown of carbohydrates and fats, which provide fuel for the muscles during prolonged exercise.
The oxidative system is important for endurance activities such as long-distance running or cycling, where sustained energy production is necessary.
Typically, exercise sessions lasting over 3 to 4 minutes will rely heavily on the oxidative system for energy production.
Learn more about oxidative energy.
brainly.com/question/28501087
#SPJ11
The position of the center of mass of a system of particles moves as x = 4.5+2.4 +2 + 1.1 t, where x is in meters. If the system starts from rest at t= 0, what is its velocity atta 3.0 s? O 8.0 m/s O 21 m/s O 44 m/s O 64 m/s O 65 m/s
The position of the center of mass of a system of particles can be expressed as a function of time. The correct answer is O 44 m/s.
In this case, the equation is x = 4.5 + 2.4t + 2t^2 + 1.1t^3, where x is in meters and t is in seconds. Since the system starts from rest at t=0, its initial velocity is zero.
To find its velocity at 3.0 seconds, we need to take the derivative of the position function with respect to time. The derivative of x with respect to t is v = 2.4 + 4t + 3.3t^2. Plugging in t = 3.0, we get v = 2.4 + 4(3.0) + 3.3(3.0)^2 = 44 m/s. Therefore, the answer is O 44 m/s.
To know more about center of mass refer here:
https://brainly.com/question/28996108#
#SPJ11
The thermal energy of a system consisting of a mass attached to a spring oscillating in vertical motion, Earth, and the air is most closely associated with (Select all that apply)
A. the gravitational interaction of the Earth and the mass.
B. the kinetic energy of the mass.
C. motions of the individual particles within the mass.
D. the kinetic energy of the earth.
E. motions of the individual particles within the air.
F. the Hooke's law interaction of the spring and the mass.
The thermal energy of a system consisting of a mass attached to a spring oscillating in vertical motion, Earth, and the air is most closely associated are :-
C. motions of the individual particles within the mass.
E. motions of the individual particles within the air.
F. the Hooke's law interaction of the spring and the mass.
The thermal energy of a system is closely associated with the motions of the individual particles within the system. In this case, the mass attached to a spring is oscillating in vertical motion, which means the particles within the mass are moving and colliding with each other, generating thermal energy. The air surrounding the mass is also moving and the particles within the air are colliding with each other, generating thermal energy. Additionally, the Hooke's law interaction between the spring and the mass also generates thermal energy. The gravitational interaction of the Earth and the mass and the kinetic energy of the Earth are not directly related to the thermal energy of the system.
To know more about thermal energy click here:
https://brainly.com/question/18989562
#SPJ11
The thermal energy of the system is associated with the motion of the individual particles within the mass and the air, as well as Hooke's law interaction between the spring and the mass.
The kinetic energy of the mass.Motions of the individual particles within the mass.Motions of the individual particles within the air.Hooke's law interaction of the spring and the mass.Hooke's law is a fundamental principle in physics that describes the relationship between the deformation of a material and the force applied to it. It states that the force required to deform a material is directly proportional to the amount of deformation. More specifically, Hooke's law states that the magnitude of the restoring force of a spring or other elastic object is proportional to the displacement or deformation of the object from its equilibrium position.
This means that if you stretch a spring or compress it, the force required to do so will be directly proportional to the amount of stretching or compression. Hooke's law is widely used in engineering and physics to analyze the behavior of materials and structures under stress. It is named after the 17th-century physicist Robert Hooke, who first observed and formulated the principle in 1676.
To learn more about Hooke's law visit here:
brainly.com/question/29126957
#SPJ4
a cable is used to raise a 25 kg urn from an underwater archeological site. there is a 25 n drag force from the water as the urn is raised at a constant speed . what is the tension in the cable?
The tension in the cable is 270.25 N.
To find the tension in the cable used to raise a 25 kg urn from an underwater archaeological site at a constant speed, with a 25 N drag force from the water, you can follow these steps,
1. Calculate the gravitational force acting on the urn: F_gravity = mass × acceleration due to gravity, where mass = 25 kg and acceleration due to gravity (g) = 9.81 m/s^2.
F_gravity = 25 kg × 9.81 m/s^2 = 245.25 N
2. Since the urn is raised at a constant speed, the net force acting on it is zero. Therefore, the tension in the cable must balance the gravitational force and the drag force.
Tension = F_gravity + Drag force
3. Plug in the values for the gravitational force and the drag force:
Tension = 245.25 N + 25 N = 270.25 N
Therefore, the cable is under 270.25 N of tension.
Learn more about "tension": https://brainly.com/question/24994188
#SPJ11
A current-carrying wire is bent into the shapeof a square of edge-length 6 cm and is placedin the ry plane. It carries a current of 2.5 A.What is the magnitude of the torque on thewire if there is a uniform magnetic field of0.3 T in the z direction?Answer in units of N-m
The magnitude of the torque on the current-carrying square wire in the uniform magnetic field is 0.0027 Nm.
1. The wire forms a square loop, and each side has a length of 6 cm or 0.06 m.
2. The current flowing through the wire is 2.5 A.
3. The magnetic field strength is 0.3 T and is in the z direction.
To find the torque, we can use the formula:
Torque = μ × B × sinθ
where μ is the magnetic moment, B is the magnetic field strength, and θ is the angle between the magnetic moment and the magnetic field.
Since the magnetic moment μ = NI × A, where N is the number of turns (1 in this case), I is the current, and A is the area of the loop:
μ = 1 × 2.5 A × (0.06 m × 0.06 m) = 0.009 Nm/T
Now, since the magnetic field is in the z direction and the loop is in the xy plane, the angle θ between the magnetic moment and the magnetic field is 90 degrees. Therefore, sinθ = 1.
Finally, calculating the torque:
Torque = 0.009 Nm/T × 0.3 T × 1 = 0.0027 Nm
In a homogeneous magnetic field, a square wire carrying current experiences a torque of 0.0027 Nm.
Learn more about "torque": https://brainly.com/question/17512177
#SPJ11
what is the critical angle θcrit for light traveling in the core and reflecting at the interface with the cladding material?
Find the wavelengths of electromagnetic waves with the following frequencies. (Assume the waves are traveling in a vacuum.) (a) 1.50 x 1019 Hz (Enter your answer in pm.) pm (b) 3.50 x 10 Hz (Enter your answer in cm.) cm
Wavelength of the wave in (a) is 20 pm and in (b) it is 8.57cm.
To find the wavelengths of electromagnetic waves with the given frequencies, we can use the formula:
wavelength = speed of light / frequency
Where the speed of light in a vacuum is approximately 3.00 x 10^8 m/s.
(a) For a frequency of 1.50 x 10^19 Hz:
wavelength = (3.00 x 10^8 m/s) / (1.50 x 10^19 Hz)
wavelength = 2.00 x 10^-11 m
To convert this to picometers (pm), we can multiply by 10^12:
wavelength = 2.00 x 10^-11 m * 10^12 pm/m
wavelength = 20 pm
Therefore, the wavelength of an electromagnetic wave with a frequency of 1.50 x 10^19 Hz is 20 pm.
(b) For a frequency of 3.50 x 10^10 Hz:
wavelength = (3.00 x 10^8 m/s) / (3.50 x 10^10 Hz)
wavelength = 8.57 x 10^-2
To convert this to centimeters (cm), we can multiply by 100:
wavelength = 8.57 x 10^-2 * 100 cm/m
wavelength = 8.57 cm
Therefore, the wavelength of an electromagnetic wave with a frequency of 3.50 x 10^10 Hz is 8.57 cm.
To know more about wavelengths, visit https://brainly.com/question/4112024
#SPJ11
if you are riding in a car that suddenly turns to the right, why do you tend to slide to the left side?
To make the relative humidity of an air mass to decrease, you would____.
A. Increase the specific humidity of the air mass
B. Decrease the temperature of the air mass
C. Decrease the dew point temperature of the air mass
D. Increase the temperature of the air mass
To make the relative humidity of an air mass decrease, you would either increase the temperature of the air mass (option D) or decrease the dew point temperature of the air mass (option C).
Option A, increasing the specific humidity of the air mass, would actually increase the relative humidity.
Option B, decreasing the temperature of the air mass, could potentially decrease the relative humidity but it would also depend on the initial specific humidity and dew point temperature of the air mass.
Learn more about relative humidity at
https://brainly.com/question/22069910
#SPJ11
Calculate the diameter and depth of a circular sedimentation basin for a design flow of 3800 m3/day based on an overflow rate of 0.00024 m/s and a detention time of 3 hr.
the diameter of the circular sedimentation basin should be approximately 15.25 meters and the depth should be approximately 2.59 meters to accommodate a design flow of 3800 m3/day based on an overflow rate of 0.00024 m/s and a detention time of 3 hours.
The overflow rate (Q) is defined as the design flow rate (Qd) divided by the surface area of the sedimentation basin (A):
Q = Qd / A
Rearranging this equation, we get:
A = Qd / Q
The detention time (t) is the volume of the sedimentation basin (V) divided by the design flow rate (Qd):
t = V / Qd
Rearranging this equation, we get:
V = Qd x t
The surface area of a circular sedimentation basin (A) is given by:
A = π x (d/2)^2
where d is the diameter of the basin.
The depth of the sedimentation basin (h) is given by:
h = V / A
Substituting the given values into the equations, we get:
Q = 0.00024 m/s
Qd = 3800 m3/day = 0.044 m3/s
t = 3 hours = 10800 seconds
From the overflow rate equation, we get:
A = Qd / Q = 0.044 m3/s / 0.00024 m/s = 183.33 m2
From the detention time equation, we get:
V = Qd x t = 0.044 m3/s x 10800 s = 475.2 m3
From the surface area equation, we get:
A = π x (d/2)^2
Solving for d, we get:
d = √(4 x A / π) = √(4 x 183.33 m2 / π) = 15.25 m
From the depth equation, we get:
h = V / A = 475.2 m3 / 183.33 m2 = 2.59 m
Therefore, the diameter of the circular sedimentation basin should be approximately 15.25 meters and the depth should be approximately 2.59 meters to accommodate a design flow of 3800 m3/day based on an overflow rate of 0.00024 m/s and a detention time of 3 hours.
Visit to know more about Sedimentation:-
brainly.com/question/3280481
#SPJ11
question 10.10: why do the areas in between the runways now appear blue
The areas in between the runways now appear blue because they have been painted with a special type of paint
What is RSA markings?The areas in between the runways now appear blue because they have been painted with a special type of paint called runway safety area (RSA) markings.
These blue markings help pilots and airport personnel identify the areas where it is safe to operate aircraft, and also serve as a visual cue to indicate the boundary of the runway area.
The blue color is also easier to see in low light conditions or during inclement weather, which helps to enhance overall safety at the airport.
Learn more about runway safety
brainly.com/question/4543399
#SPJ11
find the centripetal force exerted on a 7.12-kg mass moving at a speed of 2.98 m/s in a circle of radius 2.72 m.
The result will be the centripetal force exerted on the 7.12-kg mass as it moves in a circle with a radius of 2.72 m.
What is Centripetal Force?
Centripetal force is the force that keeps an object moving in a circular path. It is directed towards the center of the circular path and is always perpendicular to the velocity of the object. Centripetal force is necessary to constantly change the direction of motion of an object and prevent it from moving in a straight line.
The centripetal force acting on an object moving in a circular path is given by the formula:
F = (m * [tex]v^{2}[/tex]) / r
where F is the centripetal force, m is the mass of the object, v is the velocity of the object, and r is the radius of the circular path.
Given:
Mass of the object (m) = 7.12 kg
Velocity of the object (v) = 2.98 m/s
Radius of the circular path (r) = 2.72 m
Plugging these values into the formula, we can calculate the centripetal force:
F = (m * [tex]v^{2}[/tex] / r
F = (7.12 kg) * [tex](2.98 m/s) ^{2}[/tex]/ 2.72 m
Learn more about Centripetal Force from the given link
https://brainly.com/question/20905151
#SPJ1
if a ball is dropped from a height of 5 m, what will be its approximate speed when it hits the ground
The approximate speed of the ball when it hits the ground is 9.9 meters per second.
When a ball is dropped from a height of 5 meters, it will accelerate towards the ground due to the force of gravity. The acceleration due to gravity is approximately 9.8 meters per second squared. This means that every second the ball is falling, its velocity will increase by 9.8 meters per second.
To calculate the approximate speed of the ball when it hits the ground, we can use the following equation:
[tex]Vf^{2}[/tex] = [tex]Vi^{2}[/tex] + 2ad
Where Vf is the final velocity, Vi is the initial velocity (which is 0 in this case), a is the acceleration due to gravity, and d is the distance the ball falls (which is 5 meters).
Plugging in the numbers, we get:
[tex]Vf^{2}[/tex] = 0 + 2(9.8)(5)
[tex]Vf^{2}[/tex] = 98
Vf ≈ +9.9 m/s
Therefore, the approximate speed of the ball when it hits the ground is approximately 9.9 meters per second. It is important to note that this is an approximation and factors such as air resistance and the shape of the ball can affect the actual speed at impact.
Know more about speed here:
https://brainly.com/question/13262646
#SPJ11
an electromagnetic plane wave has an intensity average=800 w/m2.saverage=800 w/m2. what are the rms values rmserms and rmsbrms of the electric and magnetic fields, respectively?
The electric and magnetic fields have amplitudes of 4.63 x 105 T and 165.4 V/m, respectively.
The strength of a wave magnetic field can be calculated mathematically, right?Any wave's amplitude and energy are inversely connected. As a result, it is possible to represent the intensity of electromagnetic waves using Iave=c0E202. Iave is equal to E0, which is the maximum electric field strength of a continuous sinusoidal wave, and E0 is the average intensity in W/m2, where Iave is the latter.
The electromagnetic wave strength is inversely proportional to the rms values of the electric and magnetic fields.
[tex]S_{average}[/tex] = [tex]1/2*c*0*E_{rms} ^{2}[/tex]
If we solve for [tex]E_{rms}[/tex], we obtain:
Equation [tex]E_{rms}[/tex] = [tex]\sqrt{((2*S_{average)/(c*0)} }[/tex]
With the provided values substituted, we obtain:
Equation [tex]E_{rms}[/tex] = [tex]\sqrt{((2*800 W/m2)/(3*10^{8} m/s*8.85*10^{-12}F/m )} }[/tex]
116.7 V/m for [tex]E_{rms}[/tex].
Similar to that, the magnetic field's rms value can be determined using:
[tex]S_{average}[/tex] is equal to (half) * 1/0 *[tex]B_{rms}^{2}[/tex] * c.
0 represents the permeability of empty space. When we solve for [tex]B_{rms}[/tex], we get:
[tex]B_{rms}[/tex]is equal to[tex]\sqrt{((2*S_{average)/(c*0))} }[/tex]
Inputting the values results in:
[tex]B_{rms}[/tex]is equal to[tex]\sqrt{((2*800 W/m2)/(3*10^{8} m/s*8.85*10^{-12}F/m )} }[/tex], where [tex]B_{rms}[/tex]
b. Using the formula [tex]E_{0} =\sqrt{2*E_{rms}[/tex], it is possible to determine the amplitudes of the electric and magnetic fields.
[tex]\sqrt{2*B_{rms} }[/tex], where [tex]B_{0}[/tex]
Inputting the values results in:
[tex]E=\sqrt{2*116.7V/m}[/tex], which equals 165.4 V/m
[tex]B_{0}[/tex] is equal to[tex]\sqrt{2*3.28*10^{5} }[/tex]T and 4.63 x 105 T.
For more information on electromagnetic kindly visit to
https://brainly.com/question/17057080
#SPJ1
The electric and magnetic fields have amplitudes of 4.63 x 105 T and 165.4 V/m, respectively.
The strength of a wave magnetic field can be calculated mathematically, right?Any wave's amplitude and energy are inversely connected. As a result, it is possible to represent the intensity of electromagnetic waves using Iave=c0E202. Iave is equal to E0, which is the maximum electric field strength of a continuous sinusoidal wave, and E0 is the average intensity in W/m2, where Iave is the latter.
The electromagnetic wave strength is inversely proportional to the rms values of the electric and magnetic fields.
[tex]S_{average}[/tex] = [tex]1/2*c*0*E_{rms} ^{2}[/tex]
If we solve for [tex]E_{rms}[/tex], we obtain:
Equation [tex]E_{rms}[/tex] = [tex]\sqrt{((2*S_{average)/(c*0)} }[/tex]
With the provided values substituted, we obtain:
Equation [tex]E_{rms}[/tex] = [tex]\sqrt{((2*800 W/m2)/(3*10^{8} m/s*8.85*10^{-12}F/m )} }[/tex]
116.7 V/m for [tex]E_{rms}[/tex].
Similar to that, the magnetic field's rms value can be determined using:
[tex]S_{average}[/tex] is equal to (half) * 1/0 *[tex]B_{rms}^{2}[/tex] * c.
0 represents the permeability of empty space. When we solve for [tex]B_{rms}[/tex], we get:
[tex]B_{rms}[/tex]is equal to[tex]\sqrt{((2*S_{average)/(c*0))} }[/tex]
Inputting the values results in:
[tex]B_{rms}[/tex]is equal to[tex]\sqrt{((2*800 W/m2)/(3*10^{8} m/s*8.85*10^{-12}F/m )} }[/tex], where [tex]B_{rms}[/tex]
b. Using the formula [tex]E_{0} =\sqrt{2*E_{rms}[/tex], it is possible to determine the amplitudes of the electric and magnetic fields.
[tex]\sqrt{2*B_{rms} }[/tex], where [tex]B_{0}[/tex]
Inputting the values results in:
[tex]E=\sqrt{2*116.7V/m}[/tex], which equals 165.4 V/m
[tex]B_{0}[/tex] is equal to[tex]\sqrt{2*3.28*10^{5} }[/tex]T and 4.63 x 105 T.
For more information on electromagnetic kindly visit to
https://brainly.com/question/17057080
#SPJ1
what is the mass of this portion? express your answer in terms of the variables m , l , and r .
Using the formula m = ρV, we can express the mass in terms of the variables m, l, r, and ρ as m = ρπr²l.
To calculate the mass of this portion, we need to know the density of the material it is made of. Let's assume the density is represented by the variable ρ.
The formula to calculate the mass of a portion of a solid object is:
m = ρV
where V represents the volume of the portion.
For a cylindrical portion with length l, radius r, and height h, the volume can be calculated as follows:
V = πr²h
If we assume that the portion in question is a cylindrical slice with height h, then we can calculate the volume as follows:
V = πr²h = πr²l
Therefore, the mass of the portion can be calculated as follows:
m = ρV = ρπr²l
So, the mass of the portion can be expressed in terms of the variables m, l, r, and ρ as follows:
m = ρπr²l
In summary, to calculate the mass of the portion, we need to know its density and dimensions (length, radius, and height).
For more such questions on Mass.
https://brainly.com/question/31234195#
#SPJ11
Find T,N, and K for the space curve, where t > 0.r(t)=(cost+tsint)i+(sint−tcost)j+2k
For the space curve r(t)=(cost+tsint)i+(sint−tcost)j+2k,
Tangent vector T: T = (cos(t) + tsin(t))i + (sin(t) - tcos(t))j + 2k
Normal vector N: N = -sin(t)i + (-cos(t))j
Curvature K: K = 1/t
The given space curve r(t) is defined by three components: x = cos(t) + tsin(t), y = sin(t) - tcos(t), and z = 2. To find the tangent vector T, we differentiate each component of r(t) with respect to t, resulting in T = (cos(t) + tsin(t))i + (sin(t) - tcos(t))j + 2k. The tangent vector T represents the direction of motion of the curve at any given point.
The normal vector N is found by taking the derivative of T with respect to t, which gives N = -sin(t)i + (-cos(t))j. The normal vector N is perpendicular to the tangent vector T and represents the direction of the curvature of the curve.
The curvature K is given by K = 1/t, where t is the parameter of the curve. The curvature measures how much the curve deviates from a straight line at a particular point. In this case, the curvature is inversely proportional to the parameter t, which means that the curvature decreases as t increases.
For more questions like Vector click the link below:
https://brainly.com/question/29740341
#SPJ11
an object's moment of inertia is 1.8 kg⋅m2 . its angular velocity is increasing at the rate of 3.0 rad/s per second.
The object's angular velocity is not increasing at all, and remains constant. The torque acting on the object is 5.4 Newton meters (N/m).
The angular acceleration of the object can be found using the formula:
angular acceleration = (change in angular velocity) / time
In this case, the change in angular velocity is 3.0 rad/s per second, and we don't know the time. However, we can use another formula that relates angular acceleration, moment of inertia, and torque:
torque = moment of inertia x angular acceleration
Assuming there are no external torques acting on the object, we can set the torque to zero and solve for the angular acceleration:
angular acceleration = 0 / moment of inertia
Plugging in the given moment of inertia of 1.8 kg⋅m2, we get:
angular acceleration = 0 / 1.8 kg⋅m2 = 0 rad/s2
This means that the object's angular velocity is not increasing at all, and remains constant. If there were an external torque acting on the object, we would need to take that into account and use the first formula to find the angular acceleration.
Given that an object's moment of inertia (I) is 1.8 kg⋅m² and its angular acceleration (α) is 3.0 rad/s², we can find the torque (τ) acting on the object using the following formula:
τ = I × α
Identify the known values.
Moment of inertia, I = 1.8 kg⋅m²
Angular acceleration, α = 3.0 rad/s²
Apply the formula to find the torque.
τ = (1.8 kg⋅m²) × (3.0 rad/s²)
Calculate the torque.
τ = 5.4 N⋅m
So, the torque acting on the object is 5.4 Newton meters (N⋅m).
More on angular velocity: https://brainly.com/question/9612563
#SPJ11
you double your distance from a sound source that is radiating equally in all directions. what happens to the intensity level of the sound? it drops by group of answer choices 2 db. 3 db. 6 db. 8 db.
When you double your distance from a sound source that is radiating equally in all directions, the intensity level of the sound drops by 6 dB.
Here's a step-by-step explanation:
1. Sound intensity level (L) is measured in decibels (dB) and is related to sound intensity (I) by the formula: [tex]L = 10 \times log_{10}(\frac{I}{I_0} )[/tex], where is the reference intensity.
2. When you double the distance from a sound source, the intensity (I) is inversely proportional to the square of the distance.
3. If the initial distance is d, and the new distance is 2d, the intensity ratio [tex]\frac{I}{I_0}[/tex] will be [tex]\frac{1}{4}[/tex] times the original intensity ratio.
4. Plugging the new intensity ratio into the formula, the new intensity level will be [tex]L_2 = 10 \times log_{10}((\frac{1}{4} ) * \frac{I}{I_0} ).[/tex]
5. Comparing the initial intensity level (L1) to the new intensity level [tex]L_2[/tex], we get:[tex]L_2 = L_1 - 10 \times log_{10}(4)[/tex].
6. Simplifying, we get [tex]L_2 = L_1 - 6 dB.[/tex]
So, when you double your distance from the sound source, the intensity level drops by 6 dB.
To know more about sound refer here:
https://brainly.com/question/29707602#
#SPJ11
A wire 1.6 m in length carries a current of 5.1 A in a region where a uniform magnetic field has a magnitude of 0.76 T.
Calculate the magnitude of the magnetic force on the wire if the angle between the magnetic field and the current is 37◦.
Answer in units of N.
The magnitude of the magnetic force on the wire if the angle between the magnetic field is 2.474 N
To calculate the magnitude of the magnetic force on the wire, you can use the formula:
F = I * L * B * sin(θ)
Where F is the magnetic force, I is the current (5.1 A), L is the length of the wire (1.6 m), B is the magnitude of the magnetic field (0.76 T), and θ is the angle between the magnetic field and the current (37°).
F = 5.1 A * 1.6 m * 0.76 T * sin(37°)
F ≈ 2.474 N
Magnetic force is the force exerted by a magnetic field on a moving electric charge. A magnetic field is a region in space where a magnetic force can be detected, and it is created by the movement of electric charges, such as the movement of electrons in a wire or the movement of the Earth's molten iron core.
To know more about force please refer: https://brainly.com/question/24115409
#SPJ11
consider the bohr model of the atom. which transition would correspond to the largest wavelength of light absorbed?
According to the Bohr model of the atom, electrons can only exist in certain discrete energy levels, and when an electron moves.
What is an atom ?An atom is the basic unit of matter that consists of a nucleus, which contains protons and neutrons, and is surrounded by electrons in orbitals. The protons carry a positive charge, while the electrons carry a negative charge, and the neutrons are neutral. The number of protons in the nucleus determines the atomic number of the element, and each element has a unique number of protons. Atoms are neutral overall, with the number of electrons equaling the number of protons in the nucleus.
Atoms are incredibly small, with diameters on the order of 10^-10 meters, and are the building blocks of all matter in the universe. The behavior of atoms and their interactions with other atoms and molecules underlie all chemical and physical processes.
To know more about Atoms visit :
https://brainly.com/question/30898688
#SPJ1
a 1.00×104-kg train car moves east at 18.0 m/s. determine the magnitude of the train car's momentum .
the magnitude of the train car's momentum is 1.8 × 10^5 kg·m/s.
To determine the magnitude of the train car's momentum, we need to use the equation:
momentum = mass x velocity
The mass of the train car is given as 1.00x10^4 kg and its velocity is 18.0 m/s to the east.
So, the momentum of the train car is:
momentum = 1.00x10^4 kg x 18.0 m/s = 1.80x10^5 kg m/s
Therefore, the magnitude of the train car's momentum is 1.80x10^5 kg m/s.
Hi! I'd be happy to help you with your question. To determine the magnitude of the train car's momentum, you can use the following formula:
Momentum = mass × velocity
Given the information provided:
- Mass of the train car (m) = 1.00 × 10^4 kg
- Velocity of the train car (v) = 18.0 m/s (moving east)
Now, let's plug in the values:
Momentum = (1.00 × 10^4 kg) × (18.0 m/s)
Momentum = 1.8 × 10^5 kg·m/s (east)
So, the magnitude of the train car's momentum is 1.8 × 10^5 kg·m/s.
learn more about momentum here
https://brainly.com/question/30677308
SPJ11
When a circuit is made up of a battery, a bulb,
and a wire, how should the wire run to light up
the bulb?
When a circuit is made up of a battery, a bulb, and a wire then the wire should run either from the bulb to the battery or from the battery to the bulb to light up the bulb. Hence option C is correct.
An incandescent light bulb, incandescent lamp, or incandescent light globe is an electric light with a heated wire filament. To protect the filament from oxidation, it is encased in a glass bulb with a vacuum or inert gas. Terminals or wires implanted in the glass supply current to the filament. A bulb socket offers mechanical support as well as electrical connections.
Incandescent bulbs are available in a variety of diameters, light outputs, and voltage ratings ranging from 1.5 volts to around 300 volts( A battery of this much Voltage). They do not require any external regulating equipment, have cheap production costs, and can operate on either alternating or direct current.
To know more about Bulb :
https://brainly.com/question/30663603?
#SPJ1.