A wire of radius 0.8 cm carries a current of 106 A that is uniformly distributed over its cross-sectional area. Find the magnetic field B at a distance of 0.07 cm from the center of the wire.

Answer:

The correct answer will be:

(A) 24955495.07 N/m²

(B) 97482.40 N/m²

Explanation:

(A)

The given values are:

mass,

m = 50 kg

diameter

= 0.50 cm

then,

radius,

r = 0.25 cm

 = 0.0025 m

As we know,

⇒ [tex]A = area \ of \ cross \ section[/tex]

       [tex]=\pi r^2[/tex]

and,

⇒ [tex]stress = \frac{mg}{A}[/tex]

On substituting the values, we get

              [tex]=\frac{(50)(9.8)}{\pi (0.0025^2)}[/tex]

              [tex]=24955495.07 \ N/m^2[/tex]

(B)

mass,

m = 5000 kg

radius,

r = 20 cm

 = 0.2 m

Now,

⇒ [tex]stress=\frac{\frac{5000}{4} (9.8)}{\pi (0.2^2)}[/tex]

              [tex]=97482.40 \ N/m^2[/tex]

Answer:

Force = 49N

Explanation:

Force is given by the multiplication of mass and acceleration.

Mathematically, Force is;

[tex] F = ma[/tex]

Where;

F represents force measured in Newton.

m represents the mass of an object measured in kilograms.

a represents acceleration measured in meter per seconds square.

Given the following data

Mass = 5kg

We know that acceleration due to gravity = 9.8m/s²

To find the Force:

[tex] F = 5*9.8 [/tex]

Force = 49N

Answer:

So, at the depth of 24 cm below the surface of the glycerine the pressure is  2970 Pa. Hence, this is the required solution.

Explanation:

Given that,

Pressure exerted by the surface of glycerine, P = 2970 Pa and it is greater than atmospheric pressure.

The density of glycerine,  

We need to find the depth h below the surface of the glycerine. The pressure due to some depth is given by :

h = 0.24 meters

or

h = 24 cm

Answer:

a

Explanation:

..................

Answer:

no deflection

Explanation:

current is flowing from west to east. As the magnetic field of a long wire carrying current is circular, its direction will be north below the wire and south above the wire (according to the right hand rule). So, when the compass is placed underneath the wire, it will still point towards the north direction.

Answer:

Explanation:

According to newtons second law of motion;

F = ma .... 1

Also the force acting aong the inclines is expressed as;

F = mgsintheta

m is the mass of the object

a is the acceleration

theta is angle of inclination

Equate 1 and 2

ma = mg sin theta

a = gsin(theta)

a = 9.8sin30

a = 9.8(0.5)

a = 4.9m/s²

Hence the acceleration of the ping pong is 4.9m/s²

Answer:

   x = 2,864 m ,       Ra = 32.1 m                       

Explanation:

Let's solve this problem in parts, let's start by finding the intensity of the sound in each observer

observer A β = 64 db

             β = 10 log Iₐ / I₀

where I₀ = 1 10⁻¹² W / m²

              Iₐ = I₀ 10 (β/ 10)

let's calculate

              Iₐ = 1 10⁻¹² (64/10)

              Iₐ = 2.51 10⁻⁶ W / m²

Observer B β = 85 db

             I_b = 1 10-12 10 (85/10)

             I_b = 3.16 10⁻⁴ W / m²

now we use that the emitted power that is constant is the intensity over the area of ​​the sphere where the sound is distributed

              P = I A

therefore for the two observers

              P = Ia Aa = Ib Ab

the area of ​​a sphere is

               A = 4π R²

we substitute

               Ia 4pi Ra2 = Ib 4pi Rb2

               Ia Ra2 = Ib Rb2

Let us call the distance from the observer be to the haughty R = ax, so the distance from the observer A to the haughty is R = 35 ax; we substitute

             Ia (35 -x) 2 = Ib x2

we develop and solve

           35-x = Ra (Ib / Ia) x

           35 = [Ra (Ib / Ia) +1] x

           x (11.22 +1) = 35

           x = 35 / 12.22

            x = 2,864 m

This is the distance of observer B

The distance from observer A

            Ra = 35 - x

            Ra = 35 - 2,864

            Ra = 32.1 m

Answer:

I'm pretty sure its c

Hope you get a good grade-

Answer:

B. Sound waves will not be transformed into electrical signals.

Explanation:

edge2021

Sound waves will not be transformed into electrical signals is the reason that microphone on an AM radio is not working properly.

It is a type of mechanical wave composed of the disturbance caused by the movements of the energy. A sound wave travels through compression and rarefaction in an elastic medium such as air.

The microphone on an AM radio is not working properly means sound waves are not transforming into electrical signals.

Learn more about sound waves

brainly.com/question/11797560

#SPJ5

Answer:

A

Explanation:

Answer:

A

Explanation:

Gases in the atmosphere absorb heat.

You know when you have a blanket around you and some heat gets trapped in but some still gets out. Thats basically what it is.

Plus I got it right in multiple questions including the test!

I hope that reassured you!

Have a good night!

Answer:

D

Explanation:

Answer:

The correct option is a

Explanation:

From the question we are told that

   The mass of the block is  [tex]m = 4.84 \ kg[/tex]

    The height of the vertical  drop is [tex]h = 19.6 \ m[/tex]

Generally from the law of energy conservation , the potential energy at the top  of the slide is equal to the kinetic energy at the point after sliding this can be mathematically represented as

        [tex]PE = KE[/tex]

i.e     [tex]m * g * h = \frac{1}{2} * m * v^2[/tex]

=>    [tex]gh = 0.5 v^2[/tex]

=>   [tex]v = \sqrt{\frac{9.8 * 19.6}{0.5 } }[/tex]

=>    [tex]v = 19.6 \ m/s[/tex]

Answer:

wind orosion is the correct answer dkr this

Answer:

8) 709.8875 J

9) The object is at 7.24375 m from the ground

10) Kinetic energy increases as the object falls.

Explanation:

We use the expression for the displacement h(t) as a function of time of an object experiencing free fall:

h(t) = hi - (g/2) t^2

hi being the initial position of the object (10m) above ground, g the acceleration of gravity (9.8 m/s^2), and t the time (in our case 0.75 seconds):

h(0.75) = 10 - 4/9 (0.75)^2 = 7.24375 m

This is the position of the 10 kg object after 0.75 seconds (answer for part 9)

Knowing this position we can calculate the potential energy of the object when it is at this height, using the formula:

U = m g h = 10kg * 9.8 (m/s^2) * 7.24375 m = 709.8875 J (answer for part 8)

Part 10)

the kinetic energy of the object increases as it gets closer to ground, since its velocity is increasing in magnitude because is being accelerated in its motion downwards.

Answer:

Reverse check the answer

Explanation:

I believe it is very important that once someone is done with any calculation, the person ought to go over the calculations again. And even, recheck the answer in inverted form.

This is so because while doing the calculations, we can possibly make errors that we won't notice until after submission. Knowing 2 * 3 = 6, but writing 2 * 3 = 5 in the course of calculations can happen to anybody. So therefore, cross checking and reverse checking is needed

Answer:

Speed = 100 km/h

Explanation:

Given:

Speedometer reading = 100 kph for one lap

Assume;

Time taken to complete one lap = 1 hour

Computation:

Speed =  Distance / Time

Speed =  100 / 1

Speed = 100 km/h

Answer:

sry i need points

Explanation:

Answer:

to show the arts and creativity of the person and to show also the culture of the place..

Explanation:

Answer:

67500

Explanation:

F=ma

F = 1500 × 45

F = 67500

Answer:

hello your question is incomplete  attached below is the missing part  

answer : short period oscillations frequency  = 0.063 rad / sec

              phugoid oscillations natural frequency ( [tex]w_{np}[/tex] ) = 4.27 rad/sec

Explanation:

first we have to state the general form of the equation

= [tex]( S^2 + 2\alpha _{p} w_{np} S + w^{2} _{np} ) (S^{2} + 2\alpha _{s} w_{ns}S + w^{2} _{ns} ) = 0[/tex]

where :

[tex]w_{np} = Natural frequency of plugiod oscillation[/tex]

[tex]\alpha _{p} = damping ratio of plugiod oscilations[/tex]

comparing the general form with the given equation

[tex]w^{2} _{np}[/tex]  = 18.2329

[tex]w^{2} _{ns} = 0.003969[/tex]

hence the short period oscillation frequency ( [tex]w_{ns}[/tex] ) =  0.063 rad/sec

phugoid oscillations natural frequency ( [tex]w_{np}[/tex] ) = 4.27 rad/sec

Answer:no sure sorry

Explanation:

Answer:

a) s = 79 m W

b) s = 2 km S

c) s = 250 m W

d) s = 0 km  

Explanation:

We take the following sign convention for the directions:

North (N)  ---> positive

South (S)  ---> negative

East (E) ---> negative

West (W)  ---> positive

a)

45 m W, 34 m W

s = 45 m + 34 m

s = 79 m W

b)

5 km N, 7 km S

s = 5 km - 7 km

s = - 2 km

s = 2 km S

c)

350 m E , 800 m W, 200 m E

s = -350 m + 800 m - 200 m

s = 250 m

s = 250 m W

d)

850 km N, 850 km S

s = 850 km - 850 km

s = 0 km

Answer:

The position of the person's feet. a running shoe company studying how different surfaces affect the life of a shoe tread

Explanation:

100%

Answer:

1. The position of the person's feet.

2. A running shoe company studying how different surfaces affect the life of a shoe tread

Explanation:

100% correct

Answer:

0.56rad/s²

Explanation:

Using the equation of motion

wf = wi + αt

wf is the final angular velocity

wi is the initial angular velocity

α is the angular acceleration

t is the time

Given

wf = 11.0rad/s

wi =2.0rad/s

t = 5.5secs

Substitute into the formula and get α

11.0 = 2.0+5α

11.0-2.0 = 5α

9.0 = 5α

α = 5/9.0

α ≈ 0.56rad/s²

Hence the wheel's average angular acceleration is 0.56rad/s²

The wheel's average angular acceleration is equal to 1.64 [tex]rad/s^2[/tex].

Given the following data:

To determine the wheel's average angular acceleration, we would apply the first equation of kinematics:

Mathematically, the angular acceleration of an object is given by the formula:

[tex]\alpha = \frac{\omega_f - \omega_i}{t}[/tex]

Where:

Substituting the given parameters into the formula, we have;

[tex]\alpha =\frac{11.0\;-\;2.0}{5.5} \\\\\alpha =\frac{9.0}{5.5}[/tex]

Angular acceleration = 1.64 [tex]rad/s^2[/tex]

Read more: https://brainly.com/question/8898885

Answer:

6.56km

Explanation:

Given parameters:

Speed  = 11.5km/hr

Time  = 2060s

Unknown:

Distance covered  = ?

Solution:

Speed is distance divided by the time taken.

   Speed  = [tex]\frac{distance}{time}[/tex]

   Distance  = Speed x time

Let us convert the seconds to hours;

      3600s  = 1hr

      2060s = [tex]\frac{2060}{3600}[/tex]   = 0.57hr

Now

 Distance  = 11.5km/hr x 0.57hr  = 6.56km

Answer:

Energy

Explanation:

work is actually a transfer of energy. When work is done to an object , energy is transferred to that object.

The ability to do work is called energy.

"Work is the energy transferred to or from an object via the application of force along a displacement. In its simplest form, it is often represented as the product of force and displacement."

"Energy is defined as the “ability to do work, which is the ability to exert a force causing displacement of an object.”  energy is just the force that causes things to move. Energy is divided into two types: potential and kinetic."

Know more about energy here

https://brainly.com/question/1932868

#SPJ2

Answer:

The magnitude of the force that the 6.3 kg block exerts on the 4.3 kg block is approximately 41.9 N

Explanation:

Forces on block 4.3 kg are:

63N to the right and R21 (contact force from the 6.3 kg block) to the left

Net force on 4.3 kg block is: 63 N - R21

Forces on the 6.3 kg block are:

R12 to the right (contact force from the 4.3 kg block) and 11 N to the left.

So net force on the 6.3 kg block is: R12 - 11 N

According to the action-reaction principle the contact forces R21 and R12 must be equal in magnitude (let's call them simply "R").

Then, since the blocks are moving with the SAME acceleration, we equal their accelerations:

a1 = (63 N - R)/4.3 = (R - 11 N)/6.3 = a2

solve for R by cross multiplication

6.3 (63 - R) = 4.3 (R - 11)

396.9 - 6.3 R = 4.3 R - 47.3

369.9 + 47.3 = 10.6 R

444.2 = 10.6 R

R = 444.2 / 10.6

R = 41.90 N

Answer:

The force exerted is [tex]F = 100 \ N[/tex]

Explanation:

From the question we are told that

   The mass of the block is [tex]m_b = 10 \ kg[/tex]

    The speed is  [tex]v = 10 \ m/s[/tex]

Generally the force exerted to lift the object at constant speed is equivalent to the wight of the ball, this is mathematically represented as

       [tex]F = m * g[/tex]      Here  [tex]g = 10 \ m/s^2[/tex]

=>    [tex]F = 10 * 10[/tex]

=>    [tex]F = 100 \ N[/tex]

The force are you exerting on the block when the block is lifting straight up with constant speed is 98 N and this can be determined by using the given data.

Given :

You are lifting a 10 kg block straight up at a constant speed of 10 m/s.

The following steps can be used in order to determine the force are you exerting on the block:

Step 1 - According to the given data, the block is lifting straight up at a constant speed. So, the acceleration is zero.

Step 2 - So, the only force exerted on the block is the weight of the block.

Step 3 - So, the force are you exerting on the block is given by:

F = mg

F = 10 [tex]\times[/tex] 9.8

F = 98 N

For more information, refer to the link given below:

https://brainly.com/question/2996858

Answer:

1750Nm/s

Explanation:

70*25=1750Nm/s

Answer:

1750 kgm/s

Explanation:

The equation for momentum is p = mv = 70 * 25 = 1750