A regulator is required on a nitrogen cylinder in order to reduce very high pressure within the gas cylinder to a safer pressure.
What is a regulator?A regulator can be defined as a mechanical device that is designed and developed to ensure that a controlled amount of nitrogen gas is supplied from a gas cylinder.
This ultimately implies that, a regulator is required on a nitrogen cylinder in order to reduce very high pressure within the gas cylinder to a safer pressure.
Read more on regulator here: https://brainly.com/question/4652901
#SPJ1
Split point twist drills
Answer:
A split point twist drill is a self-centering speed bit with a cutting angle of 135 degrees. It is specifically designed to drill into metal and other hard materials without wandering around on the surface.
What are the relevance of land use capabilities
Answer:
Land capability is one aspect of land classification. For the determination of land capability, the usefulness of land for agriculture, forest and tourism is assessed solely on the basis of physical environmental factors.
Hence the capability denotes
The usefulness of landThe price and value of landThe future interactions of the landIf you measure the voltage across a diode and it measures 0.3 V, the diode is probably made of __________ and is __________ biased.
Answer:
germaniumforwardExplanation:
The forward-biased voltage drop of a semiconductor diode depends on the material it is made of and the method of fabricating the junction.
Voltage dropsA silicon diode will have a voltage drop that can be estimated as 0.7 V. The actual value will depend on current and temperature.
A germanium diode will have a voltage drop closer to 0.3 V, again depending on current and temperature.
A Schottky diode may have a voltage drop between 0.2 and 0.3 V, so may be difficult to distinguish from a germanium diode.
If it measures 0.3 V, the diode is probably made of germanium, and is forward biased.
__
The reverse-biased voltage reading will generally match the open-circuit voltage of the testing device.
Two technicians are discussing a vehicle that cranks slowly when the key is turned to the crank position. The positive battery terminal is noticably hotter than the negative terminal. Technician A says that the positive battery terminal must have an excessive voltage drop since it is hotter. Technician B says that the negative battery terminal must have an excessive voltage drop since it is cooler. Who is correct?
Answer:
Both are right
Explanation:
Miguel’s presentation on the Iron Age moving into the Middle Ages was detailed. He outlined the process of smelting and clarified how metals such as copper, tin, and bronze could be combined with intense heat to create strong iron. He added some images of tools that came into wide use, such as adzes and axes and even armor. Miguel left out one tool, however, that was highly important to the civilization’s progress. What might have been that tool, and why is it important?
A.
hammer, invaluable for building homes
B.
drinking vessel, essential for carrying water
C.
fencing, to create separation between properties
D.
heavy plough, which advanced food production
The heavy plough is the most important tool that Miguel left out of his presentation. The correct option is D.
The heavy plough was an important tool in the Iron Age and Middle Ages because it allowed farmers to cultivate more land and produce more food. This led to a population increase and a more prosperous society.
The other tools mentioned are also important, but they are not as essential as the heavy plough.
The hammer is useful for building homes, but it is not as important as the plough for food production. The drinking vessel is essential for carrying water, but it is not as important as the plough for advancing food production.
Fencing is useful for creating separation between properties, but it is not as important as the plough for advancing food production.
Therefore, the correct option is D.
To learn more about the iron age;
https://brainly.com/question/32988416
#SPJ3
Briefly explain the term soil sampling and outline its importance in building engineering works.
Answer:
For civil engineering, the importance is that you want to ensure that your construction is in a good sturdy location.
Explanation:
Im at UNCC as a civil engineering student
You are about to perform PMCS on your M1114? What resource should you use for the procedures and instructions for performing PMCS?
The resources and instructions that should be used for the procedures of performing PMCS are:
Operator's manualsSafety cautions and warnings.Fording kitHeating and cooling systems.What is PMCS?PMCS is an acronym for preventive maintenance checks and services and it can be defined as the maintenance, checks, and services that are typically performed before, during, and after the use of any type of military equipment such as:
M1114M1151M1123Basically, the resources and instructions that should be used for the procedures of performing PMCS are:
Operator's manualsSafety cautions and warnings.Fording kitHeating and cooling systems.Read more on PMCS here: https://brainly.com/question/15720250
#SPJ1
Which of the following is NOT true?
a. The Thevenin voltage is equal to the open circuit voltage
b. We can find the Thevenin resistance for any circuit by zeroing all sources and finding the equivalent resistance of the resulting network.
c. We can do a source transformation to switch between Thevenin and Norton equivalent circuits.
d. The Norton current is equal to the short circuit current.
e. The Thevenin resistance is equal to the Norton resistance.
A statement which isn't true is that: B. we can find the Thevenin resistance for any circuit by zeroing all sources and finding the equivalent resistance of the resulting network.
The true statements about these theorems.In Electrical engineering, the true statements about Thevenin's theorem and Norton's theorem include the following:
The Thevenin voltage is generally equal to the open circuit voltage.We can do a source transformation to switch between Thevenin and Norton equivalent circuits.The Norton current is the same as the short-circuit current.The Thevenin resistance is the same as the Norton resistance.In this context, we can infer and logically deduce that we cannot find the Thevenin resistance for an electrical circuit by zeroing all sources and finding the equivalent resistance of the resulting network.
Read more on Thevenin's theorem here: https://brainly.com/question/28007778
#SPJ1
Which type of software is designed to meet the specific requirements or an individual or organizations
Answer:
Tailored Software
Explanation:
The tailored software is designed to meet the specific requirement of the users and form an important part of the organisational MIS (Management Information System). Tailored software can interact and share information with the various sub components of the organisational MIS.
Hence the answer is Tailored Software
Flip-flops are normally used for all of the following applications, except ________. logic gates data storage frequency division counting
Flip-flops are normally used for all of the following applications, except logic gates.
What are Flip flops?Flip flops are known to be tools that are used for counting. They come in different ranges.
Note that Flip flops are one that can be seen on counters, storage registers, and others and as such, Flip-flops are normally used for all of the following applications, except logic gates.
Learn more about Flip flops from
https://brainly.com/question/4237777
#SPJ1
et G = (V, E) be a directed graph in which each vertex in u E V is labeled with a unique integer L(u) from the set {1, 2 ...,V]}. For each vertex u E V, let R(u) = {v E V: una v} be the set of vertices that are reachable from u (a node can always reach itself by default). Let min(u) be the vertex in R(u) with the minimum label, i.e. min(u) is vertex v such that L(v) is the smallest among all other nodes in R(u). Describe an O(V + E) time algorithm that computes min(u) for all vertices u € V,
Using knowledge in DFS algorithms it is possible to write code that can organize the vertices and create functions that understand the order of factors.
Writting in DFS algorithmdfs(node)
{
mark node as visited
//initialize ans for this node to label of this node
ans=label[node]
for every neigbor of node
{
if the neighbor is visited
{
ans=minimum(ans,calculated[neighbor])
}
else if the neighbor is unvisited
{
call dfs(neighbor)
ans=minimum(ans,calculated[neighbor])
}
}
calculated[node]=ans
}
{
if the node is not visted{
call dfs(node)
}
}
for the given example graph we get minimum label for vertices as:
1 1 1 3 3 6 (in order for a,b,c,d,e,f), so the vertex with this label are c,c,c,e,e,f.
See more about DFS algorithm at brainly.com/question/13014003
#SPJ1
how to write a 5bit register if a series is moved to the shift register from left to right
The Bidirectional Shift Register is the shift register that allows one to write a 5bit register if the series is shifted from left to right.
What is a value of a 5-bit register?A 5-bit register is valuable because it can represent up to 32 items. It is to be noted that a bit is a digit that is binary that is indicative of two states.
While a 5-bit register can have a possible number of 32 values,
6 can hold 64;7 can hold 128;8 can hold 256 etc.Learn more about registers at;
https://brainly.com/question/19091159
#SPJ1
1. Write two statements for each of the following operators using the emp
and dept tables. Be sure to include AND & OR statements as well.
OPERATORS:
= (equals)
<> (not equal to)
> (greater than)
< (less than)
in
not in
LIKE
Answer:
the answer is simply 5000250 because the phenomicals add up to the mainstream with beacoups
= 1. Set Square should be placed against the lower edge of the T-Square.
True or false?
The Set Square should be placed against the lower edge of the T-Square, so the statement is true.
The T-square must be placed up against the edge of the drawing board. There must be no gaps otherwise the paper will not be set up correctly and drawing accurate horizontal and vertical lines will be impossible. The T-square must be placed up against the edge of the drawing board. There must be no gaps otherwise the paper will not be set up correctly and drawing accurate horizontal and vertical lines will be impossible.
With that being said, it is true that the set square should be placed against the lower edge of the T-square.
See more about Drawing at: https://brainly.com/question/23033135
#SPJ1
The process of discovering discrepancies between two or more sets of data-flow diagrams or discrepancies within a single DFD is referred to as: A. logic modeling B. requirements structuring. C. DFD validation. D. DFD stress testing. E. gap analysis.
Answer:
Gap Analysis is the process of discovering discrepancies between two or more sets of data flow diagrams or discrepancies within a single DFD. it might be helpful
Protecting wiring is the key to keeping a system
in good condition. The integrity of the system is
critical to avoiding?
The integrity of this system is critical to avoiding electrocution.
What is electrocution?Electrocution refers to a process through which a certain amount of electric current (electricity) flows through the body of a living organism, thereby, causing death or leading to severe injury.
According to the occupational safety and health administration (OSHA), it is very important to protect wiring because it's the key to keeping an electrical system in good condition.
This ultimately implies that, the integrity of this system is critical to avoiding electrocution.
Read more on OSHA here: brainly.com/question/17199752
#SPJ1
Why are diode logic gates not suitable for cascading operation?
Please do not copy anything from anywhere.
Diode logic gates are not suitable for cascading operation because the pull-down or pull-up resistance within makes them a high output resistance device.
What is a cascading operation?A cascading operation refers to a process in electrical engineering which involves the use of a circuit breaker's current-limiting capacity, so as to enable an installation of lower-rated and lower-cost circuit breakers.
According to the National Electrical Code (NEC), diode logic gates are not entirely suitable for cascading operation due to the fact that the pull-down or pull-up resistance within makes them a high output resistance device.
Read more on logic gates here: https://brainly.com/question/24708297
#SPJ1
A 4KJ of energy is supplied to a machine used for lifting a mass. The force required is 800N. If the machine has an efficiency of 60℅,to what height will it lift the mass?
The height at which the mass will be lifted is; 3 meters
How to utilize efficiency of a machine?Formula for efficiency is;
η = useful output energy/input energy
We are given
η = 60% = 0.6
Input energy = 4 KJ = 4000 J
Thus;
0.6 = useful output energy/4000
useful output energy = 0.6 * 4000
useful output energy = 2400 J
Work done in lifting mass(useful output energy) = force * distance moved
Useful output energy = 800 * h
where h is height to lift mass
Thus;
800h = 2400
h = 2400/800
h = 3 meters
Read more about Machine Efficiency at; https://brainly.com/question/3617034
#SPJ1
Which scenario accurately reflects employee involvement during an onsite inspection?
Answer:
Employees may request a separate closing conference without the employer present.
Explanation:
it’s basically the answer lol
The solid cylindrical bar shown is subjected to a bending force F = 55kN, an axial load P = 8 kN, and a torsional load T = 30 kN-mm. The bar is made of AISI 1060 CD steel (Sy = 280 MPa, Sut = 330 MPa). Find the factor of safety based on Maximum Distortion Energy Theory.
The factor of Safety by Maximum Distortion Energy Theory is given as: N = 6.04
What is Maximum Distortion Energy Theory?
According to this idea, failure by yielding happens when the distortion energy per unit volume in a condition of combined stress equals that associated with yielding in a basic tension test at any location in the body.
What is the calculation for the above value?
Note that we are given the following:
A solid Steel bar subjected to a bending force of F = 55kN
Torsional load T = 30 kN-mm; and
Yield Strength (sy) = 280Mpa
Sut = 330 Mpa
The formula for Normal Stress is given as:
[tex]\alpha _{x}[/tex] = [UP/πd²] + [ (32* f * L)/πd³]
= [(4 * 8 * 10³)/π * (0.02)²] + [(32 * 55 *10³ * 0.1)/ π * (0.02)³]
= 25.46 + 7.003
[tex]\alpha _{x}[/tex]= 32.5 Mpa
Tyz = (16T)/πd³
= (16 * 30)/ π * (0.02)³
= 19.098
Tyz = 19.098
Following from the above, sate of stress, we have:
α₁ = αₓ = 32.46 Mpa; and
α₂ = Tyz = 19.098 Mpa;
α₃ = -Tyz = -p19.098 Mpa;
Utilizing the formula given by the Maximum Distortion Energy Theory:
α₁² + α₂² + α₃² - (α₁α₂ + α₂α₃ + α₃α₁)
= Sy²/N²
→ 32.46² + 19.098² + 19.098² - ( 32.46* 19.098 - 19.098² -32.46 * 19.098)
= 280/N²
N = 6.04
Learn more about Maximum Distortion Energy Theory at:
https://brainly.com/question/22435706
#SPJ1
metal _____ flashing is commonly used to waterproof joints between sloping roofs and vertical walls.
Answer:
metal step-flashing flashing is commonly used to waterproof joints between sloping roofs and vertical walls.
Hope its helpful!
Answer:
step-flashing is the answer.
Explanation:
A large retirement community wants to host a grand birthday party for its residents who recently
became centenarians (a centenarian is someone who has lived 100 years). The party organizers learn
that 25 new centenarians will be the guests of honor at the party, so they decide to prepare some
interesting facts about this group's age. They start brainstorming, and one of the organizers says,
"Hey, the standard deviation of their ages would be an interesting fact."
Which of the following best represents the standard deviation for the ages of the new centenarians?
The ideal response for the age standard deviation would be zero.
Why is there a standard deviation?A standard deviation (or σ) is a measure of how distributed the data is in reference to the mean. When the standard deviation is low, the data are concentrated around the mean, and when it is large, the data are widely dispersed.
They invited 25 persons who recently turned 100 years old, so the majority of attendees will be between the ages of 100 and 102. There is extremely little likelihood that anyone will be older than 102.
Since the majority of the data are centered at 100, the standard deviation will be zero or very close to it.
Learn more about standard deviation on:
https://brainly.com/question/475676
#SPJ1
Which of the following best represents the standard deviation for the ages of the new centenarians?
0
100
30
25
Draw a surface development of a truncated cone
The image of the drawing of a surface development of a truncated cone is given in the image attached.
What is truncated cone?The term truncated cone is defined as any section of a cone or a pyramid that is said to not have a tip and it is one that ends in a plane that is often parallel to the base.
So therefore, The image of the drawing of a surface development of a truncated cone is given in the image attached.
Learn more about truncated cone from
https://brainly.com/question/4069694
#SPJ1
calculate area moment of inertia for a circular cross section with 6 mm diameter
16 mm^4
64 mm ^4
113 mm^4
323 mm^4
1016 mm^4
The area moment of inertia for a circular cross-section with a 6 mm diameter will be 64 mm⁴. Option B is correct.
What is a moment of inertia?The moment of inertia is defined as the resistance offered in the rotation of the moment.
Given data;
The diameter of circular section ,d = 6 mm
The moment of inertia is, I
The moment of inertia for the circular cross-section;
[tex]\rm I = \frac{\pi d^4}{64} \\\\ \rm I = \frac{3.14 \times 6^4 }{64} \\\\ I = 63.585 mm^4[/tex]
The area moment of inertia for a circular cross-section with a 6 mm diameter will be 64 mm⁴
Hence option B is correct.
To learn more about the moment of inertia refer;
https://brainly.com/question/15246709
#SPJ1
8. What are used by the project architect to depict different building systems and to show how they correlate to one anothe
O A. Preliminary
O B. Shop drawings
C. Working drawings
O D. Sketches
Explanation:
????????????????????????????
write down the tracking error such that the adaptive cruise control objective is satisfied.
Answer:
The most common reason a cruise control stops working is due to a blown fuse or a defective brake pedal switch. It can also be caused by issues with the throttle control system or the ABS. In older cruise control systems it can be caused by a broken vacuum line.
x cotx expansion using maclaurins theorem.
It is to be noted that it is impossible to find the Maclaurin Expansion for F(x) = cotx.
What is Maclaurin Expansion?The Maclaurin Expansion is a Taylor series that has been expanded around the reference point zero and has the formula f(x)=f(0)+f′. (0) 1! x+f″ (0) 2! x2+⋯+f[n](0)n!
What is the explanation for the above?
as indicated above, the Maclaurin infinite series expansion is given as:
F(x)=f(0)+f′. (0) 1! x+f″ (0) 2! x2+⋯+f[n](0)n!
If F(0) = Cot 0
F(0) = ∝ = 1/0
This is not definitive,
Hence, it is impossible to find the Maclaurin infinite series expansion for F(x) = cotx.
Learn more about Maclaurin Expansion at;
https://brainly.com/question/7846182
#SPJ1
Describe how you will a use a feedback mechanism to monitor Marissa’s wellbeing and ensure that support measures are working.
Feedback mechanisms gives a way to effectively to change behavior and it can be used to monitor Marissa's wellbeing by:
Asking her consistently how she feels, how she is and getting her settled.With it, one can be able to deduce what is wrong with her and address it.What is a feedback mechanism?The aim of a feedback mechanism is one that is known to be forward focused as it helps to link one's current actions to your future results.
Therefore Feedback mechanisms gives a way to rightly to alter behavior and it can be used to monitor Marissa's wellbeing though asking her consistently how she feels, how she is and getting her settled and one can be able to find what is wrong with her and address it.
See full question below
Due to a change in ownership and management of your facility, there has been a high turnover of managers in the past six months. Staff are very confused as to what to do, what is required and who to report to causing a lot of stress and issues in the workplace. The new management put into place a change management initiative to clarify business objectives and work roles. After a few weeks, things started to settle down and staff are performing better.
Beth, a support worker approached you one day and said that Marissa, a colleague has been having emotional breakdowns lately at work, crying unexpectedly, unable to concentrate on her tasks and taking longer breaks than usual. Beth needs to repeat instructions several times before Marissa can understand a task. Her actions are disrupting other staff and Beth is concerned about any accidents with client care due to Marissa's lack of concentration.
You invite Marissa for an informal meeting to find out how she's coping. Before the meeting, you checked Marissa's HR file and discovered that she is from the Philippines and English is her second language. She's a very hard worker and clients have commended her for her caring and sensitive nature.
In the meeting with Marissa, she nervously disclosed to you that she is worried about losing her job due to all the changes in management. She cannot afford to lose her job as she is a single parent responsible for her three children. She is also having a hard time coping with different instructions and expectations from different managers and she doesn't know who she can talk to anymore.
Question 1
Describe how you will a use a feedback mechanism to monitor Marissa's wellbeing and ensure that support measures are working.
Learn more about feedback mechanism from
https://brainly.com/question/8726791
#SPJ1
a stone is thrown vertically upwards and reaches the ground after five seconds calculate the initial velocity
Answer:
50m/Sec
Explanation:
v = u-gt
u = v + gt
v = 0
t = 5
g = 10m/sec2 (9.8 is accurate)
u = 0 + (5x10) = 50 m/Sec
linear circuit consist independent and dependent element yes or no