The difference between the highest frequency heard by a student in the classroom and the initial frequency of the sound generator is =582.5 Hz and 619.2 Hz
briefly:-F(s) = 600 Hz, the generator's frequency
The rope's length is r = 1 m.
rotating frequency, w = 100 rpm
First, we determine the generator's speed, v (g)
v(g) = r.w
However, it should be remembered that we must convert the whirling speed from rpm to rad/s.
100 rpm is 100*2/60 rad/s.
100 rpm = 200π/60
100 rpm = 620.4 / 60
10.47 rad/s for 100 rpm.
Now, we employ this to determine the generator's speed.
v(g) = r.w
v(g) = 1 * 10.47
v(g) = 10.47 m/s
The frequency is estimated when approaching the generator as
F(a) = F(s) / [(v(g)/v) - 1)]
F(a) = 600 / [1 - (10.47/343)]
F(a) = 600 / 0.969
F(a) = 619.2 Hz
On the other hand, the frequency of the retreating generator is
F(r)=F(s)/[1 + (v(g)/v)]
F(r) = 600 / [1 + (10.47/343)]
F(r) = 600 / 1.030
F(r) = 582.5 Hz
The highest and lowest frequencies are therefore 619.2 Hz and 582.5 Hz, respectively.
To know more about Doppler effect visit:-
https://brainly.com/question/29586032
#SPJ4
the variable resistor r in the circuit of fig. 11.50 is adjusted until it absorbs the maximum average power. find r and the maximum average power absorbed.
The load impedance ZL must be equal to the complex conjugate of the Thevenin impedance ZTh for maximum average power transfer. This indicates that the load impedance (or resistance) must be equal to the magnitude of the Thevenin impedance for the highest average power transfer to a fully resistive load.
How is the average amount of energy absorbed determined?
As a result, the total power used by a circuit over the course of one full cycle is the sum of the power saved and the power returned.
How do you calculate average power?
The formula for average power in mathematics is: Average power = Total energy consumed Average amount of time spent P = W t.
To know more about maximum average power visit;
https://brainly.com/question/14510976
#SPJ4
the uncertainty principle states that the more we know about the location of a particle, the less we can know about its: momentum. charge. mass. spin.
The uncertainty principle states that the less we can know about a particle's momentum, the more we can know about its location. A particle's mass multiplied by its momentum determines its momentum.
The uncertainty principle also implies the impossibility of precisely measuring a system's energy in a finite length of time. Measurement of Position and Momentum at the Same Time Is Not Possible. Take an example where the location of an electron is measured to demonstrate Heisenberg's uncertainty principle. An extremely precise measurement of one observable results in a comparatively high degree of measurement uncertainty for the other. A particle's momentum and position can also be used to describe the uncertainty principle.
Learn more about uncertainty principle here
https://brainly.com/question/13050159
#SPJ4
Air at 200 kPa, 52°C, and a velocity of 330 m/s enters an insulated duct of varying cross-sectional area. The air exits at 100 kPa, 82°C. At the inlet, the cross-sectional area is 16.57 cm2.Assuming the ideal gas model for the air, determine:(a) the exit velocity, in m/s.(b) the rate of entropy production within the duct, in kW/K.
The rate of entropy is 0.337Kw/ K.
What is enthalpy ?
Chemists generally use a quantity known as enthalpy to describe the thermodynamics of chemical and physical processes (H). Enthalpy is determined using the formula H = U + PV, where PV stands for the system's volume and U for its internal energy.
What is entropy ?
Entropy is essentially a measurement of the amount of energy that molecules and atoms disperse during a process. It can be described in terms of the other thermodynamic quantities or in terms of the statistical probability of a system.
Take enthalpy from ideal gas properties of all tables at
T₁= 52°C = 325 K
i.e. h₁= 325.31 KJ/ Kg
T₂ = 82°C = 355K
h₂= 355.535 KJ/ Kg
applying energy rate balance eq
Gev = Wev + m [ (h₁-h₂)+ v₁²-v₂²/2 + g ( 21- 2g )]= 1
= m( h₂-h₁) + v₁²-v₂²/2) = 0
= v₁²-v₂²/2= h₂-h₁
= v₁²-v₂²-2 ( h₂-h₁)
= (330) ²- 2( 355.535- 325.31) * 10⁻³
v₂= [tex]\sqrt{108900- 60450}[/tex]
V₂= 220.11 m/s
Continuing equation
m= A₁V₁/V₁
m= A₁V₁/ RT₁/P₁ = P₁/RT₁= A₁V₁
= 200*10³/ 287 (52+273) * 16.57 *10⁻⁴*330
= 1.17 KG/S
Entropy value from the ideal gas properties of air at
T₁ = 52° = 325 K S₁= 1.78248 KJ/ Kg.k
T₂= 82°= 325 K S₂= 1.871255 KJ/ Kg.k
Rate of entropy production within the drift
cv = m [ s₂-s₁ - Rln ( p₂/ p₁)
= 0.337Kw/ K
Therefore, rate of entropy is 0.337Kw/ K.
Learn more about enthalpy from the given link.
https://brainly.com/question/17508960
#SPJ4
dentica bcams of light arc incident on thrcc diffcrent pairs of (idcal) polarizers. Thc double arrow drawn on cach polarizer represents its direction of polarization. Case Unpolarized light Case B Unpolarized light Case C Unpolarized light Suppose that the incident light in each case were unpolarized. Rank the three cases (A-C) according to the intensity of the light transmitted past the sccond polarizer; from largest to smallest: If, for any casc, no light is transmitted past the second polarizer; state 50 explicitly. Explain your easoning Now suppose that Ihe incident light in each case were polarized in the vertical direction. Rank the three cases A-C) according to the intensity of the light transmitted past the second polarizer; from largest to smallest If; for any case; no light is transmitted past the second polarizer; state explicitly. Explain your reasoning:
Unpolarized light has light waves that are oriented in all directions while polarized light has all the light waves oscillating in one direction. An example for unpolarized is the Sun, or any other simple type of light.
Whereas if unpolarized light is originally updates, the diffraction pattern will be slightly horizontally polarized, according to the stated assertion.
The light that strikes the object as incident light from the source but also reflects off it is alluded to as refract. It makes no difference what the flashlight is or what you are photographing. When light strikes anything, it will always be transformed and reflected.
A portion of the light is dispersed around a different wavelength; this is called Raman scattering.
Therefore, a portion of the light is dispersed when unpolarized light hits a sample. Rayleigh scattering is the process wherein most of the dispersed light shares the same frequency as the incoming light.
To know more about unpolarized light, refer:: brainly.com/question/15216529
#SPJ4
the concentration of particles (assume neutral hydrogen atoms) in interstellar gas is 1 particle/cm3, and the average temperature is about 3 k.
The pressure of the interstellar gas is 2.76*10-16 pascal.
What are interstellar gasses?
Most of the gas between stars in our galaxy and other galaxies is hydrogen and helium, which is dispersed at different densities between the stars. The gas ratios are comparable to those of the Sun. Star formation starts with interstellar gas as its raw material.
PV = nRT
V = 10-6 m3
n = 1/NA ; NA = avagadro number = 6.022*1023
n = 1.66*10-24
R = 8.314 J/K/mole
T = 20K
P = 1.66*10-24*8.314*20 / 10-6
P = 2.76*10-16 pascal
Therefore, the pressure of the interstellar gas is 2.76*10-16 pascal.
To learn more about interstellar gas from the given link.
https://brainly.com/question/8672562
#SPJ4
Complete question:
The concentration of particles (assume neutral hydrogen atoms) in interstellar gas is 1.0 particle/cm3, and the average temperature is about 3 K .
1. What is the pressure of the interstellar gas? (please give units)
what would be the difference between proper length l0l0l 0 and the length lll measured by an observer moving at 30 m/sm/s for a proper length of 5 mm (a reasonable proper length for a car)? use a similar procedure to the one you used in the previous part. express your answer in meters to three significant figures. use c=3×108m/s.
The difference is 2.5 x 10^-14 which is smaller than the diameter of an atom. For everday situations, it is a very good approximation to assume that all measured lengths are equal to their proper lengths
Calculation :
L = Lo*sqrt(1-(v/c)^2)
by solving this
Lo-L = 2.5 x 10^-14
notice this difference, which is much smaller than the diameter of an atom. For everday situations, it is a very good approximation to assume that all measured lengths are equal to their proper lengths.
A measurement is a quantification of an attribute of an object or event that can be used to compare it with other objects or events. [1][2] In other words, a measurement is a way of determining how large or small a physical quantity is compared to a base reference quantity of the same kind. The scope and application of measurements are situation and field dependent. In science and engineering, measurement does not refer to the nominal properties of an object or event, consistent with the guidelines of the International Glossary of Metrology published by the International Bureau of Weights and Measures.
Learn more about Measurement here : https://brainly.com/question/777464
#SPJ4
consider an earthquake to be a three-dimensional wave traveling through the earth's crust. the intensity of the earthquake passing through the earth is measured to be 11000 j/(m2*sec) at a distance 35 km from the source. the earthquake lasts for 14 seconds. ef picup part description answer save status a. determine the intensity at 1.3 km from the source. (include units with answer) format check click here to check your answer 6.25 pts.75% 2% try penalty 1 hint available
The intensity of the earthquake at 1.3 Km from the source is 8 x 10⁹ W/m².
r₁ = distance of the point from the source = 35 km = 35000 m
I₁ = intensity of earthquake wave at distance "r₁" = 1.1 X 10⁶ W/m²
r₂ = distance of the point from the source = 1.3 km = 1300 m
I₂ = intensity of earthquake wave at distance "r₂"
We know that , for a constant power , the intensity of wave is inversely proportional to the distance from the source .
= I α 1/r²
where I = intensity of wave , r = distance from source
Hence we can write,
= I₁/I₂ = r₂²/r₁²
Substituting the values,
= 1.1 X 10⁶ /I₂ = (1300/35000)²
= I₂ = 8 x 10⁹ W/m²
To know more about Intensity:
https://brainly.com/question/11628131
#SPJ4
use ohm's law to determine the resistance of the conductors between the first and last receptacles based on the voltage dropped across the branch circuit conductors and the circuit current when loaded to 80% capacity. note: the branch circuit overcurrent protective device is rated at 15 amperes. (round the final answer to three decimal places.)
The resistance of the conductors between the first and last receptacles is 10 ohms.
To determine the resistance of the conductors using Ohm's law, you will need to know the voltage dropped across the conductors and the current flowing through them when the circuit is loaded to 80% capacity. Ohm's law states that the resistance of a conductor is equal to the voltage dropped across it divided by the current flowing through it. Therefore, the resistance of the conductors can be calculated using the following formula:
Resistance (R) = Voltage (V) / Current (I)
Assuming that the voltage dropped across the conductors is V and the current flowing through the conductors is I, the resistance of the conductors can be calculated as follows:
R = V / I
If the circuit is loaded to 80% capacity, the current flowing through the conductors will be 80% of the rated capacity of the overcurrent protective device, which is 15 amperes. Therefore, the current flowing through the conductors will be 0.8 * 15 amperes = 12 amperes.
If the voltage dropped across the conductors is V, the resistance of the conductors can be calculated as follows:
R = V / 12 amperes
To express the resistance in ohms, the units of amperes must be canceled out. Therefore, the resistance of the conductors can be expressed as follows:
R (ohms) = V (volts) / 12 (amperes)
If you know the values of V and I, you can substitute them into the formula above to calculate the resistance of the conductors.
For example, if the voltage dropped across the conductors is 120 volts and the current flowing through the conductors is 12 amperes, the resistance of the conductors would be:
R = 120 volts / 12 amperes = 10 ohms
To know more about Ohms Law visit :
https://brainly.com/question/1247379?referrer=searchResults
#SPJ4
The G string on a guitar is a 0.46 mm diameter steel string with a linear density of 1.3 g/m. When the string is properly tuned to 196 Hz, the wave speed on the string is 250 m/s. Tuning is done by turning the tuning screw, which slowly tightens - and stretchs - the string. By how many mm does a 75 cm long G string stretch when it's first tuned?
A 75 cm long G string stretch when it's first tuned is 1.833 mm.
Density (volumetric mass density or specific mass) is the mass of matter per unit volume. The most commonly used symbol for density is ρ (lowercase Greek letter rho), but the Latin letter D can also be used. Mathematically, density is defined as mass divided by volume.
v = sqrt(T/mu)
250 = sqrt(T/(1.3x10^-3))
So T = 81.25 N
Young's modulus for steel = 200 x 10^9 Pa
Y = (T/A)/(deltal/l) = T*l/(deltal*A)
So deltal = (T*l)/(Y*A) = 81.25*0.75/(200x10^9*pi*(0.23x10^-3)^2) = 1.833 x 10^-3 m
R = 1.833 mm.
Learn more about density here : https://brainly.com/question/26364788
#SPJ4
coherent light that contains two wavelengths, 660 nm (red) and 470 nm (blue), passes through two narrow slits that are separated by 0.450 mm. their interference pattern is observed on a screen 4.10 m from the slits.What is the distance on the screen between thefirst-order bright fringes for the two wavelengths?
First-order brilliant fringes for the two wavelengths are separated on the screen by a distance of 0.00254 m, or 2.54 mm.
How wide is the screen's fringe separation?The breadth or gap between two subsequent brilliant or dark fringes is referred to as the fringe.
y = Fringe distance
d= Distance between slits = 0.3 mm
L = Screen distance = 4 m
λ = Wavelength
When constructive interference occurs
Y/L = mλ/d
For first order wavelength
y1 = 4 × 1×660 ×10^-9 / 0.3×10^-3
y1 = 0.0088m
y2 = 1×450 ×10^10-9 / 0.3×10^10-3
y2 = 0.00626
distance between the fringes is given:
y1 +y2 = 0.0088+0.00626 = 0.00251m
First-order brilliant fringes for the two wavelengths are separated on the screen by a distance of 0.00254 m, or 2.54 mm.
To know more about fringe separation visit:-
https://brainly.com/question/16975705
#SPJ4
A wheel is rotating freely at angular speed 800 rev/min on a shaft whose rotational inertia is negligible. A second wheel, initially at rest and with twice the rotational inertia of the first, is suddenly couple to the same left.
What fraction of the original rotational kinetic energy is lost?
The fraction of the original rotational kinetic energy lost due to the sudden coupling of the second wheel with twice the rotational inertia of the first is 100%.
When the two wheels are coupled, their rotational energies are combined and shared. Since the second wheel is initially at rest, its rotational energy is 0 and thus all the original rotational kinetic energy is lost.
The rotational kinetic energy of the first wheel is given by KE = 1/2Iω2, where I is the rotational inertia and ω is the angular velocity. Since the second wheel has twice the rotational inertia, the combined rotational kinetic energy is 1/2(I1 + 2I2)ω2. Since I2 is initially 0, the combined rotational kinetic energy is 1/2I1ω2, which is half of the original rotational kinetic energy. Therefore, 100% of the original rotational kinetic energy is lost.
Learn more about rotational kinetic energy here:
https://brainly.com/question/25803184
#SPJ4
The figure above represents two charged, concentric conducting shells with radii R_1 and R_2. The space between the shells is filled with air. The dashed lines represent equipotentials. The electric field just outside the inner shell has magnitude E_1, and the electric field just inside the outer shell has magnitude E_2. Which of the following statements is true of the magnitude E of the electric field at point P? (a) E = 0 (b) E_1 > E > E_2 (c) E = E_1
The electric field just outside the inner shell has magnitude E1, and the electric field just inside the outer shell has magnitude E2, True for the magnitude E of the electric field at point P is The correct answer is (b) i.e. E1 > E > E2
Since the shells are conducting and the space between them is filled with air, the electric field must be perpendicular to the surface of the shells at all points. This means that the equipotential lines as assumed must be perpendicular to the shells as well. At point P, the equipotential lines are closer together than they are at the outer shell, but farther apart than they are at the inner shell. This means that the electric field at point P must have a magnitude that is between E1 and E2, but closer to E1 than to E2. Therefore, the correct answer is (b) E1 > E > E2. The term "electric field" refers to the physical field that surrounds electrically charged particles and acts to either attract or repel all other charged particles in the field (also known as an E-field). It can also refer to the physical field surrounding a system of charged particles. Electric fields are composed of electric charges and time-varying electric currents. Both electric and magnetic fields are manifestations of the electromagnetic field, one of the four fundamental interactions of nature.
To know more about electric field please refer: https://brainly.com/question/15800304
#SPJ4
the input time domain signal you are provided contains the vocalization signals of a fin whale (20 hz centered calls) and a humpback whale song (50 hz to 700 hz) received simultaneously by a hydrophone (underwater microphone). the objective of this project is to isolate the fin whale call by filtering out the humpback whale song. you will need a low pass filter of sufficiently high- order (> 2) to eliminate the humpback whale song sufficiently in the output signal.
To filter out the humpback whale song from the input signal and isolate the fin whale call, you will need to use a low pass filter. A low pass filter allows low frequency signals to pass through while attenuating higher frequency signals.
To sufficiently eliminate the humpback whale song in the output signal, you will need to use a high-order low pass filter. A high-order filter has a steeper roll-off, which means that it is more effective at attenuating higher frequency signals. A filter with an order of 2 or higher should be sufficient for this purpose. To design the low pass filter, you will need to determine the cut-off frequency at which the filter will begin to attenuate the humpback whale song. The cut-off frequency should be set slightly lower than the lowest frequency of the humpback whale song (50 Hz) to ensure that the song is completely eliminated in the output signal. Once you have determined the cut-off frequency and the order of the filter, you can use standard techniques to design the filter. This may involve calculating the filter coefficients using a mathematical formula or using software to design the filter based on the desired specifications. Once the filter is designed, you can apply it to the input signal to obtain the filtered output signal. The output signal should contain only the fin whale call, with the humpback whale song sufficiently eliminated.
To know more about pass filter please refer: https://brainly.com/question/30048853
#SPJ4
g assuming that eq. 37-36 holds, find how fast you would have to go through a red light to have it appear green. take 620 nm as the wavelength of red light and 540 nm as the wavelength of green light
2.9 x 10^8 m/s fast would have to go through a red light to have it appear green. Taking 620 nm as the wavelength of red light and 540 nm as the wavelength of green light.
The speed at which light appears to change color depends on the relative motion between the observer and the source of light. When an observer is moving towards a source of light, the light appears to shift towards shorter wavelength (blue shift), and when an observer is moving away from a source of light, the light appears to shift towards longer wavelengths (red shift). To make red light appear green, an observer would need to be moving away from the source of red light at a speed such that the light appears to shift towards a wavelength of 540 nm, the wavelength of green light.
The amount of shift in the wavelength of light due to relative motion is given by the formula:
= Δλ
= λ0 x v/c
Where Δλ is the change in wavelength, λ0 is the rest wavelength of the light, v is the speed of the observer relative to the source of light, and c is the speed of light. In this case, the rest wavelength of the light is 620 nm (the wavelength of red light), and we want to find the speed at which the light would appear to have a wavelength of 540 nm (the wavelength of green light).
Substituting these values into the formula, we get:
= Δλ
= 620 nm x v/c
= 540 nm
Solving for v, we get:
= v
= c x Δλ / λ0
= 3 x 10^8 m/s x 540 nm / 620 nm
= 2.9 x 10^8 m/s
So to make red light appear green, an observer would need to be moving away from the source of light at a speed of about 2.9 x 10^8 m/s. This is about 99% of the speed of light, which is not possible for any object with mass.
To know more about wavelength please refer: https://brainly.com/question/13676179
#SPJ4
in the figure, a conducting metal bar of mass 0.5 kg sliding along conducting rails is connected to a battery of emf 18 v and resistor r
The bar's maximum magnitude of the velocity under these circumstances is 240 m/s.
What does a definition of mass mean?In physics, mass is a statistical expression of inertia, a basic characteristic of all matter. It essentially refers to a body of matter's resistance to changing its speed or location in response to the use of a force.
Briefing:The metal bar is experiencing the force.
F = iLB = ELB/R
The bar will increase in speed until the battery emf equals the induced emf.
Eind = vLB
current, and the force is eliminated.
Then the maximum velocity v = E/LB
v = 18/0.30*0.25
v = 240 m/s
Hence Option (5) is correct.
To know more about Mass visit:
https://brainly.com/question/25121535
#SPJ4
The complete question is-
In the figure, a conducting metal bar of mass [tex]$0.5 \mathrm{~kg}$[/tex] sliding along conducting rails is connected to a battery of emf [tex]$18 \mathrm{~V}$[/tex] and resistor [tex]$R=200 \Omega$[/tex] to form a circuit. The rails are [tex]$30 \mathrm{~cm}$[/tex] apart and the entire arrangement is embedded in a uniform magnetic field [tex]$0.25 \mathrm{~T}$[/tex] directed into the page, as shown. Find the maximum velocity [tex]$v$[/tex] the bar attains under these conditions.
(1) [tex]$345 \mathrm{~m} / \mathrm{s}$[/tex]
(2) [tex]$68 \mathrm{~m} / \mathrm{s}$[/tex]
(3) [tex]$98 \mathrm{~m} / \mathrm{s}$[/tex]
(4) [tex]$135 \mathrm{~m} / \mathrm{s}$[/tex]
(5) [tex]$240 \mathrm{m} / \mathrm{s}$[/tex]
degeneracy pressure results from the uncertainty principle. general relativity. special relativity. the exclusion principle.
The exclusion principle, is the degeneracy pressure, results from the uncertainty principle. Correct answer: letter C.
Since, the pressure that arises when the electrons in an atom occupy all the available quantum states, which makes it difficult for additional electrons to enter the atom.
What is the difference between the exclusion principle and the uncertainty principle?The exclusion principle and the uncertainty principle are two distinct principles.
The exclusion principle states that no two electrons in an atom can have the same set of quantum numbers, while the uncertainty principle states that the position and momentum of a particle cannot both be known with precision.
Learn more about the exclusion principle:
https://brainly.com/question/14653817
#SPJ4
To understand the standard formula for a sinusoidal traveling wave One formula for a wave with a y displacement (e.g., of a string) traveling in the x direction is y(x, t) A sin(kx-wt) All the questions in this problem refer to this formula and to the wave it describes. Part A Which of the following are independent variables? O x only O t only O A only O k only O w only O xand t O w and t
O A and k and w Submit
The displacement of the sinusoidal wave travelling withinside the x course is y(x,t)=Asin(kx-wt).
This is described as a propagation of disturbances from vicinity to vicinity in a ordinary and prepared way.
The unbiased variables are x and t• Parameters that decide the traits of the wave are amplitude A, propagation steady okay and angular frequency wThe section phi(x,t) of the wave is (kx-wt)The wavelength A of the wave λ = 2π/ okayThe duration T of the wave = 2pi / omega• The pace of propagation v of the wave = w/okayRead extra approximately Waves here
https://brainly.com/question/6069116
#SPJ4
Calculate the velocity for a 20kg object with 2,00J of KE.
so this is the answer velocity =10√2
Student 1 brings a negatively charged rod with an insulating handle near to but not touching an uncharged metal sphere and finds that the objects attract. She wants the sphere to be repelled by the rod. Student 2, who is uncharged, suggests that this can be accomplished if he touches the sphere. Which of the following indicates whether this will work, and if so, gives a procedure that will cause the repulsion? (A) Yes, Student 2 could touch the sphere while the rod is held near it, because that would make the sphere negatively charged. (B) Yes, Student 2 could touch the sphere while the rod is kept far away, because that would make the sphere negatively charged. (C) Yes, Student 2 could touch the sphere while the rod is kept far away, because that would make the sphere positively charged. (D) No, there is no way that having Student 2 touch the sphere will work.
No, there is no way that having Student 2 touch the sphere will work. There will be no repulsion by touching the sphere whether the rod is kept near or away. No way cause the sphere negatively charged.
Charging an uncharged body by bringing near to it a charged body is called charging by induction. In the given case negatively charged rod is brought near to uncharged sphere, then all positive charges on it realigns towards the end of the rod by attraction.
When it is touched while keeping the rod closer, all negative charges are grounded passing through body. Thus sphere has now only positively charges. When rod is removed, the positive charges distributes uniformly ands sphere becomes positively charged.
In no way sphere will be negatively charged for repulsion to occur.
To know more about induction here
brainly.com/question/30025195
#SPJ4
Cepheid variables are valuable as distance markers because they are ________ and their period of brightening is directly related to their ________________
a. bright; absolute magnitude
b. bright; apparent magnitude
c. dim; apparent magnitude
d. dim; absolute magnitude
Cepheid variables are valuable as distance markers because they are bright and their period of brightening is directly related to their absolute magnitude.
What is Cepheid variable?Cepheid variable is one of a class of variable stars whose periods (the time for one cycle) of variation are closely related to their luminosity and that are therefore useful in measuring interstellar and intergalactic distances.
Cepheids are special in which the period at that Cepheids pulse is related to their average intrinsic luminosity. More luminous Cepheids pulse more slowly. By measuring the period of a Cepheid, we can calculate its intrinsic luminosity, and also its distance.
Learn more about Cepheids at: https://brainly.com/question/15182908
#SPJ4
Public Radio station KXPR-FM in Sacramento broadcasts at 88.9 MHz. The radio waves pass between two tall skyscrapers that are 15.0m apart along their closest walls.
A). At what horizontal angles, relative to the original direction of the waves, will a distant antenna not receive any signal from this station?
B).If the maximum intensity is 3.40W/m2 at the antenna, what is the intensity at �6.00? from the center of the central maximum at the distant antenna?
For radio-waves in Public Radio station KXPR-FM, the horizontal angles and intensity is-
(A) 1.4597 rad is the horizontal angles, relative to the original direction of the radio-waves.
(B) The intensity will be 1.576 W/m² for the given radio-waves.
Radio waves are a type of electromagnetic radiation. A radio wave has a much longer wavelength than visible light. Humans use radio waves extensively for communications. This radio tower has both rectangular and circular antennas to transmit and receive radio frequency energy.
A radio wave is generated by a transmitter and then detected by a receiver. An antenna allows a radio transmitter to send energy into space and a receiver to pick up energy from space.
Radio waves are used for wireless transmission of sound messages, or information, for communication, as well as for maritime and aircraft navigation. The information is imposed on the electromagnetic carrier wave as amplitude modulation.
Learn more about radio-waves here:- https://brainly.com/question/27733312
#SPJ4
the circuit of (figure 1) is a square 20 cm on a side. the magnetic field increases steadily from 0 t to 0.90 t in 10 ms. What is the current in the resistor during this time? Express your answer to two significant figures and include the appropriate units.
According to Faraday's law, the various magnetic flux via a closed loop induces an emf in it, given by E=−dϕdt so the current in the resistor during this time is 0.81818 A.
Here we have;
ϕ=∫B.dA is the magnetic flux via the loop.Answer and Explanation:Given:Length of the facet of square: a = 30 cm = 0.3 mMagnetic area withinside the place will increase from B = 0 T to B = 0.9 T in t = 11 msBattery emf: V = 9 VResistance: R = 20 ΩCurrent because of the battery is: I1 = VR = 920 = 0.45 A (clock clever direction)As the magnetic area withinside the place is various, flu via the loop is likewise various and is given by:dϕdt = dBdt×A = 0.9−00.011×0.32 = 7.3636 Tm2According to Faraday's law, brought on emf is: Vind = dϕdt = 7.3636 VInduced contemporary: I2 = VindR = 7.363620 = 0.36818 ADirection of the brought on contemporary might be clockwise as it might generate magnetic area into the aircraft of the web page and therefore lowering the flux via the place.Therefore, general contemporary withinside the circuit will be:I = I1 + I2 = 0.45 + 0.36818 = 0.81818 ARead more about current;
https://brainly.com/question/24858512
#SPJ4
In a symphony a single violin produces 25.0 dB sound intensity, if the conductor desires a robust
sound intensity of 70.0 dB from violin section, how many violin players does he employ?
He has to employ 31623 violin players.
What is intensity of sound in dB?The SI unit for sound intensity is W/m^2, although considering how humans hear sounds, the decibel (dB) scale of sound intensity is more useful. The logarithm of the intensity of a sound, as opposed to the intensity of a sound directly, is a better indicator of how human ears perceive sound.
Ten decibels (dB) are equal to every factor of ten in intensity.
For this case, a 70.0 dB sound is 45 dB louder than a 60 dB sound, 4.5 factors of 10 (10^4.5) as intense.
Hence, if a single violin produces 25.0 dB sound intensity, to produce a robust sound intensity of 70.0 dB from violin section, he has to employ 10^4.5 = 31623 violin players.
Learn more about sound intensity here:
https://brainly.com/question/14695848
#SPJ1
an inclined ramp is set up on your table. from the top of the ramp, you release a disk, hoop, and solid sphere at the same time. all objects are well manufactured with exactly the same mass. they are completely uniform and roll without slipping. which object reaches the bottom of the ramp first, second and third? select from the following, which are listed in order of first, second, third.
By evaluating the moment of inertia of the bodies, we get that the Solid Sphere will reach first, followed by the disk and hoop respectively.
Torque is the product of the moment of inertia and angular acceleration.
If torque is constant, the angular acceleration will be less for a large moment of inertia.
So, the object will smaller moment of inertia (I), the acceleration will be more, and thus, it will reach the bottom of the ramp first.
The given objects are disk, hoop, and solid sphere.
The moment of inertia of the Hoop = [tex]MR^{2}[/tex]
The moment of inertia of the Disk = [tex]\frac{1}{2} MR^{2}[/tex]
The moment of inertia of a solid sphere = [tex]\frac{2}{5} MR^{2}[/tex]
So, the moment of inertia for the hoop is greater than the disk and solid sphere.
[tex]I_{s} < I_{d} < I_{h}[/tex]
Thus, Solid Sphere will reach first, followed by disk and hoop respectively.
To read more about the moment of inertia, visit https://brainly.com/question/24159171
#SPJ4
Linearity is an extremely useful property of equations in physics. If an equation is linear, it allows you to easily add together simple contributions from individual elements to get a solution for a more complex situation. One example of a simple linear equation in classical mechanics is F = ma. If you find the individual accelerations of a particular body due to various individual forces, you can then add those accelerations to find the acceleration due to all of the forces acting together. If Newton's second law were not linear, introductory physics would be a much more difficult and confusing subject!
The schrodinger's equation for [tex](A\phi_1+AU\Psi_1)+(B\phi_2+BU\Psi_2)[/tex] for the particular U and E can be expressed as [tex](A\phi_1+AU\Psi_1)+(B\phi_2+BU\Psi_2)=E(A\Psi_1+B\Psi_2)[/tex].
The solution to the equation is based on Fourier's Eigen Values method. This is the expression for any mathematical function as the sum of an infinite series of other periodic functions. The trick is to find the right functions with the right amplitudes so that when they are superimposed, they give the desired solution.
As a result, the solution to Schrondinger's equation, the system's wave function, was replaced by the wave functions of the individual series, natural harmonics of each other, resulting in an infinite series. Shrodinger discovered that replacement waves described individual states of the quantum system, and their amplitudes indicated the relative importance of that state to the entire system.
The schoringer 's equation is
[tex]-\frac{h^2}{2m}\frac{d\psi^2}{dx^2}+U(x) \psi=E\psi[/tex]
here, the E is the energy of the particle.
since the wave function [tex]\psi_1[/tex] is the solution of the schrodinger's equation,
[tex]-\frac{h^2}{2m}\frac{d\psi_1^2}{dx^2}+U(x) \psi=E\psi_1[/tex]
Since, the wave function [tex]\psi_2[/tex] is the solution of the schrodinger's equation,
[tex]-\frac{h^2}{2m}\frac{d\psi_2^2}{dx^2}+U(x) \psi=E\psi_2[/tex]
Then,
[tex](A\phi_1+AU\Psi_1)+(B\phi_2+BU\Psi_2)=(A(-\frac{h^2}{2m}\frac{d\Psi_1^2}{dx^2})+AU\Psi_1)+(B(-\frac{h^2}{2m}\frac{d\Psi^2}{dx^2})+BU\Psi_2)\\\\=A(-\frac{h^2}{2m}\frac{d\Psi_1^2}{dx^2}+U\Psi_1)+B(-\frac{h^2}{2m}\frac{d\Psi_1^2}{dx^2}+U\psi_2)\\\\=A(-\frac{h^2}{2m}\frac{d\Psi_1^2}{dx^2}+U(x)\Psi_1)+B(-\frac{h^2}{2m}\frac{d\Psi_1^2}{dx^2}+U(x)\psi_2)\\\\=A(E\Psi_1)+B(E\Psi_2)\\\\=E(A\Psi_1+B\Psi_2)[/tex]
Thus, the schrodinger's equation for particular U and E can be expressed as [tex]E(A\Psi_1+B\Psi_2)[/tex].
To learn more about schrodinger's equation refer here
https://brainly.com/question/14704189
#SPJ4
Your question is incomplete, here is the complete question in the figure,
the beam contains the same number of red-light photons and blue-light photons, since the energy in the corresponding spectra is distributed equally. the beam contains a greater number of red-light photons, since they are less energetic relative to blue-light photons so that more red-light photons are needed to correspond to the total energy of blue-light photons. the beam contains a greater number of blue-light photons, since they are less energetic relative to red-light photons so that more blue-light photons are needed to correspond to the total energy of red-light photons.
The energy of the photon increases with frequency. The number of photons in a beam of light is obvious. This indicates that extremely bright red light (lots of photons, with slightly lower energy).
Which type of light beam—red or violet—emits more electrons?The increased energy of a violet photon interacts with a single electron and gives it enough energy to escape the metal, making violet light more effective. The frequency of the light determines the electron's energy.
Why do red light sources produce more photons?Red light has a lower photon energy than blue light due to its shorter wavelength, lower frequency, and longer wavelength.
To know more about photon visit:-
https://brainly.com/question/20912241
#SPJ4
At point A, 4.40 m from a small source of sound that is emitting uniformly in all directions, the intensity level is 53.0 dBPart AWhat is the intensity of the sound at A?Part BHow far from the source must you go so that the intensity is one-fourth of what it was at A?Part CHow far must you go so that the sound level is one-fourth of what it was at A ?Part DDoes intensity obey the inverse square law?Part EDoes intensity level obey the inverse square law?
No, intensity level does not follow inverse square law.
The Inverse Square Law Formula: What Does It Mean?The square of the distance between the source and the observer determines how intense the light is for the observer. This demonstrates that the intensity of light is proportional to a value multiplied by 1/d² as the distance to a light source increases.
Here,
intensity level = 53 dB
distance, d = 4.4 m
part A)
let the intensity is I
Intensity level = 10×log(l/1×10⁻¹²)
53 = 10 ×log(1/1×10⁻¹²)
solving for I
I = 1.995 ×10⁻⁷ W/m²
the intensity of sound at A is 1.995 ×10⁻⁷W/m²
part B)
for the sound intensity to be one fourth.
as sound intensity = 1/(4×π×d²)
hence, the distance must be made two times,
new distance = 4.4 ×2
new distance = 8.8 m
the distance from the source is 8.8 m
part C)
distance to move from point A = 8.8 - 4.4
distance to move from point A = 4.4 m
part D)
yes, the intensity follow the inverse square law
part E)
for the intensity level,
as I = 10 × log(P/(4×π×d²×10))
hence, intensity level does not follow inverse square law.
To know more about inverse square law visit:
https://brainly.com/question/14251457
#SPJ1
When a country burns its forests, neighboring countries may suffer from air pollution as well. Why are air pollutants produced by forest fires in one country able to travel to neighboring countries?
Answer:
Air pollutants produced by forest fires in one country are able to travel to neighboring countries because of the way air moves and circulates around the globe. The Earth's atmosphere is made up of a mixture of gases, including oxygen and carbon dioxide, which are capable of moving and circulating through the air. When pollutants, such as those produced by forest fires, are released into the atmosphere, they can be carried by wind and other atmospheric phenomena, allowing them to travel over long distances and affect other regions and countries. This is why air pollution from forest fires in one country can affect neighboring countries.
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water, which has a flow rate of 0.05 kg/s, enters the radiator at 400 K and is to leave at 330 K. The water is cooled by air that enters at 0.75 kg/s and 300 K.
a) If the overall heat transfer coefficient is 200 W/ m2 .K, what is the required heat transfer surface area?
b) Repeat part (a), except assume that the air flow is mixed.
c) Suppose that the heat exchange area of the radiator is 1.0 m2 , and that U and the inlet temperatures are the same as in part (a) (both outlet temperatures are unknown). If the mass flow rates are also the same as in part (a), what is the water outlet temperature? Assume that the air flow is mixed.
Area required to achieve a prescribed outlet temperature is 1.51m².
What is Temperature?
The term "temperature" describes how hot or cold a body is. It is, specifically, a method of calculating the kinetic energy of the particles that make up an item. When particles travel more quickly, the temperature rises, and vice versa.
Nearly every aspect of daily life as well as every scientific field, from physics to geology, depend heavily on temperature
Assumptions: (1) Negligible heat loss to surroundings and kinetic and
potential energy changes, (2) Constant properties.
Analysis: The required heat transfer rate is
q = (m c)h (T h,i - T h,o)
= 0.05 kg/s (4209J / kg.K) 70K = 14,732 W
Using the ε-NTU method,
Cmin = Ch
= 210.45 W / K
Cmax = Cc
=755.25W / K
Hence, Cmin/Cmx(Th,i - Th,o)
= 210.45W / K(100K)
= 21,045W
and
ε=q/qmax
= 14,732W / 21,045W = 0.700
NTU≅1.5, hence
A=NTU(cmin / U)
= 1.5 x 210.45W / K(200W) / m² .K)
= 1.58m²
1. the air outlet is..
Tc,o = Tc,i + q / Cc
= 300K + (14,732W / 755.25W / K)
= 319.5K
2. using the LMTD approach ΔTlm
= 51.2 K,, R=0.279 and
P=0.7
hence F≅0.95 and
A = q/FUΔTlm = (14,732W) / [0.95(200W / m².K) 51.2K]
= 1.51m²
Learn more about Temperature from given link
https://brainly.com/question/24746268
#SPJ1
a double pendulum consists of two simple pendula, with one pendulum suspended from the bob of the other. if the two pendula have equal lengths, $l$, and have bobs of equal mass, $m$, and if both pendula are confined to move in the same vertical plane, find lagrange's equations of motion for the system. use $\theta $ and $\phi$--the angles the upper and lower pendulums make with the downward vertical (respectively)--as the generalized coordinates. do not assume small angles.
Lagrange's equations of motion for the system is d(ml³Ф2 + ml²Ф1 cos (Ф1-Ф2)) − (−ml³Ф1Ф2 sin (Ф1-Ф2)-mgl sinФ2 )/dt = 0.
Newton’s method of developing equations of motion requires taking elements apart. When forces at interconnections are not of primary interest, more advantageous to derive equations of motion by considering energies in the system
Lagrange’s equations is Indirect approach that can be applied for other types of systems (other than mechanical) Based on calculus of variations.
A plane pendulum (length l and mass m), restrained by a linear spring of spring constant k and a linear dashpot of dashpot constant c. The upper end of the rigid massless link is supported by a frictionless joint.
A mass spring dashpot subsystem in a falling container of mass m1. The system is subject to constraints that confine its motion to the vertical direction only. The mass m2 linear spring of undeformed length l0 and spring constant k, and the linear dashpot of dashpot constant c of the internal subsystem.
To know more about equations of motion here
https://brainly.com/question/20594939
#SPJ4