A compound is made of 6.00 grams of oxygen, 7.00 grams of nitrogen, and 20.00grams of hydrogen. Find the percent composition of the compound.

A O-18.18%, N-21.21%, H-60.60%
B O-11.18%, N-22.21%, H-69.60%
C O-20%, N-30%, H-50%
D O-60.60%, N-21.21%, H-18.18%

The question is incomplete, the complete question is;

A student prepared several aqueous sodium chloride (NaCl) solutions to observe boiling point elevation at various molal concentrations, however, several errors were made throughout the procedure. Determine whether these errors would cause the observed boiling point to be increased or decreased relative to the expected boiling point, based on the procedure, or have no effect on the experimental results.

* The flask is washed with water but not thoroughly dried before preparing the solution

* The mass of NaCl used to prepare the solution is 5.400 grams instead of 4.400 grams

* Some of the prepared solution splashes out of the flask prior to observation of the boiling point

* When making the salt solution, 55.0 milliliters of water is added instead of 50.0 milliliters

Answer:

The flask is washed with water but not thoroughly dried before preparing the solution  - decrease

The mass of NaCl used to prepare the solution is 5.400 grams instead of 4.400 grams

-increase

Some of the prepared solution splashes out of the flask prior to observation of the boiling point- have no effect

When making the salt solution, 55.0 milliliters of water is added instead of 50.0 milliliters- decrease

Explanation:

If the flask is washed but not dried, then the solution will be further diluted than expected. As a result of this further dilution, the observed boiling point will be less than the expected boiling point because the boiling point depends on the solution's concentration.

If more solute is added than expected, the concentration of the solution is increased and the boiling point also increases above the expected boiling point due to the increase in amount of solute present.

If some of the solution splashes out of the flask prior to boiling, the boiling point is not affected because the concentration of the solution was not altered. The boiling point only changes when the concentration of the solution is changed.

If 55 ml of water is added instead of 50 ml, the solution is now more dilute than expected thereby reducing the concentration of the solution and the boiling point. Remember that, as the concentration of the solution decreases, the boiling point decreases accordingly.

Answer:

B. The same exact

Explanation:

I think B because in order to be a clone of your parent you have to have the exact same DNA and chromosomes.

Hope this helps :D

A clone has the same exact chromosomes as its parent.

CLONING:

Learn more at: https://brainly.com/question/12483409?referrer=searchResults

Chemical Changes

Chemical changes take place at the molecular level. A chemical change produces a new substance. Another way to think of it is that a chemical change accompanies a chemical reaction. Examples of chemical changes include combustion (burning), cooking an egg, rusting of an iron pan, and mixing hydrochloric acid and sodium hydroxide to make salt and water.

Physical Changes

Physical changes are concerned with energy and states of matter. A physical change does not produce a new substance, although the starting and ending materials may look very different from each other. Changes in state or phase (melting, freezing, vaporization, condensation, sublimation) are physical changes. Examples of physical changes include crushing a can, melting an ice cube, and breaking a bottle.

How to Tell Chemical & Physical Changes Apart

A chemical change makes a substance that wasn't there before. There may be clues that a chemical reaction took places, such as light, heat, color change, gas production, odor, or sound. The starting and ending materials of a physical change are the same, even though they may look different.

hope this helps

5 star and brainliest?

Answer:

Explanation:

here's the answer hope it helps! :)

Answer:

This indicates there will be the densest (heaviest) liquid on the bottom of the jar there will be the least dense (lightest) liquid on top. Syrup, glycerin, water, oil, and then alcohol would be on top of the order of liquids from hardest to lightest.

Answer:

b) The mass of your total product is greater than your total reactants

Explanation:

Mass of reactants is 20 and product is 25 which never occurrs in real

The molecules move faster and farther apart when the state changes from the liquid state to the gaseous state.

The matter exists in different forms in nature. Some substances have a fixed shape like wood and stone and can flow, take the shape of their container such as water, while there are forms of matter that do not have certain shapes or sizes.

In solids, the molecules are closely packed and thus solids have a rigid structure. The compact packing of solids means that the molecules are very close to each other and the molecules do not show movement. The kinetic energy of molecules in the solid is the least.

In liquids, the molecules are some distance away from each other and they show movements. Since the molecules in liquid show significant movement, they have some kinetic energy. The kinetic energy of molecules in the liquid is greater than that of solids.

In gases, the molecules are farther from each other and thus their molecules show large amounts of movement. The kinetic energy in gases is the greatest in comparison to solids and liquids.

Learn more about states of matter, here:

https://brainly.com/question/13233345

#SPJ2

Answer:

I can't see any picture?????

Answer:

V = 0.03735 mL

Explanation:

Given that,

Mass of a substance, m = 88.9 grams

Density of a substance, d = 2.38 g/mL

We need to find the volume occupied by the object. The density of an object is given by mass per unit volume.

[tex]d=\dfrac{m}{V}\\\\V=\dfrac{m}{d}\\\\V=\dfrac{88.9}{2.38}\\\\V=37.35\ mL\\\\V=0.03735\ L[/tex]

So, the volume of the substance is 0.03735 mL.

Answer:

1. B 2.B

Explanation:

Answer:

120 extracted from the gas

Explanation:

The amount of heat required now to achieve that process is 60 J of heat added to the gas.

The amount of heat required to achieve the process is calculated as follows;

[tex]E = \frac{3}{2} nR\Delta T[/tex]

where;

[tex]E = \frac{3}{2} \times 0.032 \times 8.314 \times (150)\\\\E = 60 \ J[/tex]

Thus, the amount of heat required now to achieve that process is 60 J of heat added to the gas.

Learn more about amount of heat here: https://brainly.com/question/13439286

#SPJ2

Answer:

H₂   +   Cl₂    →    2HCl

Explanation:

The given reaction expression is shown below:

      H₂   +   Cl₂    →    HCl

We are to balance this given reaction expression.

Let us do this mathematically;

       aH₂   +   bCl₂    →    cHCl

Conserving H :  2a  = c

                   Cl:   2b  = c

Now, let a  = 1, c  = 2 , b = 1

So:

            H₂   +   Cl₂    →    2HCl

Answer:

I don't get it is it even a question?

Answer: suspensions  are a mixture in which solute particles do not disolve. An example is oil and water, oil and water or even flour and water; oil can’t disolve in water

Answer:

Noun: a mixture in which particles are dispersed throughout the bulk of a fluid.

Adjective: the state of being dispersed in a fluid.

Explanation:

I used a dictionary lol

Answer:

Fluorine (F)

Explanation:

The poorest conductor of electricity from the given choices is fluorine. This is because fluorine is a non - metal.

Like other non - metals, fluorine does not conduct electricity.

Only metals are known to conduct electricity and heat readily.

Semi - metals like silicon will conduct electricity under specific condition.

The free mobile electrons in metals makes it easy for them propagate electricity

Answer:

32.7 g

Explanation:

Step 1: Write the balanced combustion reaction

C₄H₁₀ + 6.5 O₂ ⇒ 4 CO₂ + 5 H₂O

Step 2: Calculate the moles corresponding to 99.0 g of CO₂

The molar mass of CO₂ is 44.01 g/mol.

99.0 g × 1 mol/44.01 g = 2.25 mol

Step 3: Calculate the moles of C₄H₁₀ needed to produce 2.25 moles of CO₂

The molar ratio of C₄H₁₀ to CO₂ is 1:4. The moles of C₄H₁₀ needed are 1/4 × 2.25 mol = 0.563 mol.

Step 4: Calculate the mass corresponding to 0.563 moles of C₄H₁₀

The molar mass of C₄H₁₀ is 58.12 g/mol.

0.563 mol × 58.12 g/mol = 32.7 g

Answer:

predator

Explanation:

Wolves, arctic foxes, and snowy owls are predators in the tundra.

This question is incomplete, the complete question is;

Consider this reaction:

2H₃PO₄(aq) → p₂o₅(aq) + 3H₂O(aq)

At a certain temperature it obeys this rate law.

rate = ( 46.65 M⁻¹.s⁻¹) [ H₃PO₄ ]²

Suppose a vessel contains H₃PO₄  at a concentration of 0.660 M .

Calculate how long it takes for the concentration of H₃PO₄  to decrease  to 20.0% of its initial value .

You may assume no other reaction is important.

Round your answer to significant digits.

Answer:

time taken is 8.574 × 10⁻⁴ s

Explanation:

Given that;

rate = k[ H₃PO₄ ]²

rate constant k = 46.65 M⁻¹.s⁻¹)

Initial concentration A₀ =  0.660 M { which will be 100%}

final concentration At = 20%

for the concentration of H₃PO₄  to decrease  to 20.0% of its initial value = ?

we know that;

rate constant k =  1/t [ 1/At - 1/A₀ ]

we substitute

46.65 = 1/t [ 1/20 - 1/100 ]

46.65 = 1/t [ 0.04 ]

46.65 = 0.04/t

46.65t = 0.04

t = 0.04 / 46.65

t = 0.0008574  ≈ 8.574 × 10⁻⁴ s

Therefore, time taken is 8.574 × 10⁻⁴ s

Answer:

The molarity of the acid, H₂SO₄ is 3.57 M

Explanation:

We'll begin by writing the balanced equation for the reaction. This is illustrated below:

H₂SO₄ + 2NaOH —> Na₂SO₄ + 2H₂O

From the balanced equation above,

Mole ratio of the acid, H₂SO₄ (nₐ) = 1

Mole ratio of the base, NaOH (n₆) = 2

Finally, we shall determine the molarity of the acid, H₂SO₄. This can be obtained as follow:

Volume of base, NaOH (V₆) = 38.70 cm³

Molarity of base, NaOH (M₆) = 1.90M

Volume of acid, H₂SO₄ (Vₐ) = 10.30 cm³

Molarity of acid, H₂SO₄ (Mₐ) =?

MₐVₐ / M₆V₆ = nₐ/n₆

Mₐ × 10.3 / 1.9 × 38.70 = 1/2

Mₐ × 10.3 / 73.53 = 1/2

Cross multiply

Mₐ × 10.3 × 2 = 73.53 × 1

Mₐ × 20.6 = 73.53

Divide both side by 20.6

Mₐ = 73.53 / 20.6

Mₐ = 3.57 M

Thus, the molarity of the acid, H₂SO₄ is 3.57 M

Answer:

B. The temperature of the water when the food sample has finished burning completely.

Explanation:

Heat or thermal energy is a form of energy that transfers from one object to another due to a temperature difference between the objects. The units for heat are joules or calories.

Calorimetry is the measurement of heat energy released or absorbed in a chemical  reaction. A calorimeter is used in calorimetry. The calorimeter operates on the Law of Conservation of Energy which states that energy is never created or destroyed but is transformed from one form to another or between objects.

In food calorimetry, the energy released when food is burned is measured by recording the rise in temperature of water in a calorimeter when a given mass of a food sample is burned completely.

Energy can be calculated using the formula: Q = mc ∆T

where Q = the energy in joules or calories, m = the mass in grams, c = specific heat and ∆T = the change in temperature (final temperature - initial temperature).

The temperature of the water when the food sample has finished burning completely is taken as the final temperature of the water. The sample is allowed to smolder for sometime before recording the final  water temperature. This is because the water temperature will continue to rise after the  flame has gone out.

Answer:

1.  ¹⁰₄Be ---> ¹⁰₅B + ⁰₋₁β

2. ³⁴₁₄Be ---> ³⁴₁₅P + ⁰₋₁β

3. ¹⁹²₇₈Pt -----> ¹⁹⁰₇₆Os + ⁴₂α

4.  ²⁸₁₂Mg ---> ²⁸₁₃Al + ⁰₋₁β

Explanation:

1. In the first equation, Beryllium-10 isotope undergoes beta-decay, emitting a beta-particle to form boron-10 isotope. The balanced nuclear equation is given below:

¹⁰₄Be ---> ¹⁰₅B + ⁰₋₁β

2. In this reaction, silicon-34 isotope undergoes beta-decay, emitting a beta-particle to form phosphorus-34 isotope. The balanced nuclear equation is given below:

³⁴₁₄Be ---> ³⁴₁₅P + ⁰₋₁β

3. In this equation, platinum-192 isotope undergoes alpha-particle decay emitting an alpha-particle to form osmium-190 isotope. The balanced nuclear equation is given below:

¹⁹²₇₈Pt -----> ¹⁹⁰₇₆Os + ⁴₂α

4. In this equation, magnesium-28 isotope undergoes beta-decay, emitting a beta-particle to form aluminum-28 isotope. The balanced nuclear equation is given below:

²⁸₁₂Mg ---> ²⁸₁₃Al + ⁰₋₁β

Answer:

Ba(OH)2 + H2SO3 = BaSO3 + H2O -

Explanation:

Answer:

C

Explanation:

0.10 moles of Fe[tex]_2[/tex]O[tex]_3[/tex]  are in 17.2g. Therefore, the correct option is option D among all the given options.

The inorganic chemical with both the formula Fe[tex]_2[/tex]O[tex]_3[/tex] is iron(III) oxide and ferric oxide. It is one of three major iron oxides, the other 2 including iron(II) oxide (FeO), which would be uncommon, and iron(II,III) oxides (Fe[tex]_2[/tex]O[tex]_3[/tex]), which naturally occurs as the mineral magnetite. 

Acids have a high affinity for Fe[tex]_2[/tex]O[tex]_3[/tex] . Iron(III) oxide is commonly referred to as rust, and this name is appropriate to some extent because rust has certain features and has a comparable composition; nevertheless, in chemistry, colouration is classified under Hydrous ferric oxide.

mole =  17.2/ 159.69 =0.10moles

Therefore, the correct option is option D.

To know more about iron(III) oxide, here:

https://brainly.com/question/8834237

#SPJ2

Answer:

3.39x10⁻⁹ M

Explanation:

Let's assume we have 1 mL of the stream. With a density of 1.0 g/mL, we would have 1 g of the stream.

Now we calculate the mass of mercury present in 1 g of the stream, using its given concentration (0.68 ppb):

Now we convert that mass into moles, using mercury's atomic mass:

Finally we calculate the molarity of mercury, as we know that there are 3.39x10⁻¹² Hg moles in 1 mL of the stream:

Answer:

An ionic bond is the electrostatic force that holds ions together when they form bonds

Explanation:

An ionic bond is formed when a metal looses electron(s) to a non metal leading to the formation of a positive ion and a negative ion.

An ionic compound is actually an ion pair, the ions are held together by strong electrostatic forces.

This strong electrostatic force that holds the ion pair together in ionic compounds is what we commonly call the IONIC BOND.  

Answer:

An ionic bond is the electrostatic force that holds ions together when they form bonds

Explanation:

I took this test and it was the correct answer :)

Answer:

yes, but its better to drink water

Explanation:

Answer:

0.48g

Explanation:

Given parameters:

Mass of zinc  = 15g

Unknown:

Mass of hydrogen gas = ?

Solution:

To solve this problem, we need to state the balanced reaction expression first;

          Zn   +   2HCl   →   ZnCl₂    +   H₂

Find the number of moles of Zn;

    Number of moles  = [tex]\frac{mass}{molar mass}[/tex]    = [tex]\frac{15}{63.4}[/tex]    = 0.24mol

From the balanced reaction expression;

             1 mole of Zn will produce 1 mole of H₂  

            0.24mole of Zn will produce 0.24mole of hydrogen gas

Mass of hydrogen gas  = number of moles x molar mass

                                      = 0.24 x (2 x 1)

                                      = 0.48g

The number of Hydrogen atoms = 6 atoms

Given

Reaction

N₂ + 3H₂ ⇒ 2NH₃

Required

The number of Hydrogen atoms

Solution

The reaction coefficient of a chemical equation shows the mole ratio of the reacting compound.

On a compound the reaction coefficient indicates the number of molecules

Whereas the subscript after the atom shows the number of atoms in that compound

Product from the reaction : 2NH₃

Number of H-atoms :

= 2 x 3

= 6 atoms

Answer:

evolution

Explanation:

Answer:

because bird species are reproduced sexually

so there would be some variations in every generation.

that's why birds could be different from their ancestors.