Answer:
Explanation:
The color of a surface can affect how much solar energy it absorbs or reflects. Black surfaces absorb more solar radiation than lighter-colored surfaces, which reflects more of the sunlight. This is because black surfaces have a lower albedo, which is a measure of how much light a surface reflects.
When a black surface, such as a road, is exposed to sunlight, it absorbs more of the sun's energy, which is then converted into heat. This heat is then transferred to the soil underneath the road surface, where it can be stored for later use. During winter, the pipes running through the soil can be used to extract this stored heat and warm the cold water, which can then be used to melt ice on the road surface.
Therefore, the black surface of the road is beneficial for this energy storage system because it allows for more efficient absorption of solar energy, which can then be used to heat the soil and melt ice during the winter months.
other end of the string is tied to a rigid support. the potato is held straight out horizontally from the point of support, with the string pulled taut, and is then released.what is the speed of the potato at the lowest point of its motion?
To determine the speed of the potato at the lowest point of its motion, we need to consider conservation of mechanical energy.
When the potato is held horizontally and released, its potential energy (PE) is converted into kinetic energy (KE) as it swings along the string. At the initial point, when the potato is held horizontally, its height above the lowest point can be represented by the length of the string (assuming it's a perfectly horizontal release).
Thus, the initial PE can be calculated as PE_initial = mgh, where m is the mass of the potato, g is the acceleration due to gravity (approximately 9.81 m/s²), and h is the length of the string. At the lowest point of the potato's motion, its height is zero, meaning its potential energy is also zero (PE_final = 0). All the initial potential energy has been converted into kinetic energy (KE), so KE_final = PE_initial.
The final kinetic energy can also be represented as KE_final = 0.5 * m * v², where v is the speed of the potato at the lowest point. Equating the expressions for initial potential energy and final kinetic energy, we have:
0.5 * m * v² = mgh
The mass of the potato (m) can be canceled out from both sides, leaving:
v² = 2gh
To find the speed (v) at the lowest point, take the square root of both sides:
v = √(2gh) So, the speed of the potato at the lowest point of its motion depends on the length of the string (h) and the acceleration due to gravity (g).
To know more about speed click here
brainly.com/question/2822401
#SPJ11
Paper (a dielectric material) is inserted between plates of a capacitor that hold a charge. This causes the electric field to become _______.
The causes the electric field to become weaker, as the presence of the dielectric material reduces the overall capacitance of the capacitor.
The dielectric material like paper is inserted between the plates of a capacitor holding a charge, the electric field becomes weaker. This happens because the dielectric material reduces the effective electric field between the capacitor plates by aligning its internal dipoles with the field. As a result, the capacitance of the capacitor increases, allowing it to store more charge at the same voltage.Adding a dielectric allows the capacitor to store more charge for a given potential difference. When a dielectric is inserted into a charged capacitor, the dielectric is polarized by the field. The electric field from the dielectric will partially cancel the electric field from the charge on the capacitor plates.
learn more about dielectric material here
https://brainly.com/question/30523009
#SPJ11
what is the total work done by the two tugboats on the supertanker? express your answer in joules, to three significant figures.
The total work done by the two tugboats on the supertanker is 100,000,000 joules, to three significant figures.
To calculate the total work done by the two tugboats on the supertanker we need to know the force exerted by the tugboats and the distance over which they exerted the force. Let's assume that the force exerted by each tugboat was 500,000 newtons and that they pulled the supertanker distance of 100 meters.
The work done by each tugboat is given by the formula:
work = force x distance
So, the work done by each tugboat is:
work = 500,000 newtons x 100 meters = 50,000,000 joules
Since there are two tugboats, the total work done by both tugboats is:
total work = 2 x 50,000,000 joules = 100,000,000 joules
Learn more about work here:
https://brainly.com/question/29762840
#SPJ11
2-24 a reinforcing rod can be driven about 30 cm into sand soil estimate the soils strength and describe it's condition
The soil strength is estimated to be low, as the reinforcing rod can only penetrate 30 cm into the sand soil. This indicates that the soil is not very compact and has low bearing capacity. The condition of the soil can be described as loose and granular, as it is composed of sand particles.
What is soil strength?Soil strength is a measure of the soil's ability to resist external forces, such as shear, tension, and compression. It is an important factor in the design of structures such as buildings, roads, and other civil engineering projects. Soil strength is affected by the soil's grain size, mineralogy, and water content. For example, soils with larger grain size, higher proportion of silt and clay, and higher water content tend to have higher soil strength values. Factors such as compaction, freezing and thawing, and the presence of organic matter can also affect soil strength.
To learn more about soil strength
https://brainly.com/question/29858595
#SPJ4
during the testing of a new light bulb, a sensor is located a distance of 51.5 cm from the bulb. it records an intensity of 373.9 w/m2 for the radiation emitted from the bulb. what is the rms value of the magnetic field at that location? (in t)
The RMS value of the magnetic field at the location of the sensor is approximately 0.0141 T, To calculate the RMS value of the magnetic field at that location,
we can use the formula for the intensity of electromagnetic radiation Intensity (I) = (1/2) * c * μ₀ * B², where c is the speed of light (3 × 10^8 m/s), μ₀ is the permeability of free space (4π × 10^-7 Tm/A), and B is the RMS value of the magnetic field.
First, we need to rearrange the formula to solve for B:
B = sqrt(2 * I / (c * μ₀))
Now we can plug in the given values:I = 373.9 W/m²
Distance = 0.515 m (convert 51.5 cm to meters)
Note that the distance is not relevant in this calculation, as we are given the intensity at the location of the sensor.
B = sqrt(2 * 373.9 / (3 × 10^8 * 4π × 10^-7))
B = sqrt(747.8 / (3.767 × 10^6))
B = sqrt(0.000198)
B ≈ 0.0141 T
The RMS value of the magnetic field at the location of the sensor is approximately 0.0141 T.
To know more about speed click here
brainly.com/question/2822401
#SPJ11
12) What do astronomers consider heavy elements? A) elements that are heavier than iron B) elements that are heavier than carbon C) elements that are heavier than hydrogen D) elements that are heavier than uranium E) all elements besides hydrogen and helium
Astronomers consider heavy elements to be all elements besides hydrogen and helium. These elements include those that are heavier than iron, carbon, hydrogen, and uranium.
These elements are also referred to as "metals" in astronomical terms, even though they include non-metallic elements from the periodic table. Astronomers consider elements heavier than helium—such as carbon, nitrogen, oxygen, neon, magnesium, silicon, sulfur, chlorine, argon, calcium, iron, and others—as heavy elements. These elements make up the bulk of the matter in the universe, and they are essential for the formation of stars, planets, and even life. Astronomers are particularly interested in these elements because they can provide valuable information about the formation and evolution of galaxies, stars, and other objects in the universe.
To learn more about heavy elements click here https://brainly.com/question/23089267
#SPJ11
Question 40 Marks: 1 What material has a high melting point, a high atomic number and is used as a target material to produce x-rays?Choose one answer. a. copper b. lead c. aluminum d. tungsten
The material that has a high melting point, a high atomic number and is used as a target material to produce x-rays is tungsten.
Tungsten has a high melting point of 3,422 °C (6,192 °F) and a high atomic number of 74. It is also used as a target material to produce x-rays in medical imaging and industrial processes. Tungsten is the most common target material used for producing x-rays, as it has a low production cost and is more resistant to damage than other materials. It is also non-toxic and does not present any health risks. It has a body-centered cubic structure and is extremely hard, making it an ideal choice for high temperature applications.
To learn more about x-rays click here https://brainly.com/question/1454365
#SPJ11
A person riding a bicycle in a straight line at 7.5 miles per hour would be more balanced than the same person riding the bicycle at 4.8 miles per hour in a straight line.
TRUE or false
The speed at which a person rides a bicycle in a straight line does not necessarily affect their balance.
Balance on a bicycle is more dependent on the rider's ability to maintain their center of gravity over the bike's center of gravity, regardless of the speed they are traveling. The correct answer is false.
Factors that can affect a rider's balance on a bicycle include the terrain they are riding on, the weight and distribution of their body and any cargo on the bike, and any external forces such as wind or sudden movements.
In fact, some riders may find it easier to maintain balance at slower speeds as they have more time to react and make adjustments to their position on the bike.
On the other hand, riding at a very high speed can be more challenging for some riders as they may need to make quick and precise movements to maintain their balance.
Overall, while speed can impact a rider's experience on a bicycle, it is not the sole determinant of balance.
Riders of all abilities and speeds can work to improve their balance through proper positioning, practice, and adjusting to different riding conditions.
To know more about center of gravity here
https://brainly.com/question/20662235
#SPJ11
Balance is unaffected by the pace at which a person is riding a bicycle in a straight line. Regardless of the rider's speed.
balance on a bicycle is more reliant on their capacity to keep their center of gravity above the centre of gravity of the bike. False is the proper response.
The surface they are riding on, the weight and distribution of their body and any cargo on the bike, and any external forces like wind or unexpected movements are all variables that might impact a rider's balance on a bicycle.
In fact, because they have more time to react and modify their posture on the bike, some riders may find it simpler to maintain balance at slower speeds.
On the other hand, some riders may find it more difficult to ride at very high speeds because they may need to make quick, precise movements to keep their balance.
Overall, although it can affect a rider's experience on a bicycle, balance is not solely determined by speed. Through good positioning, practise, and adaptation to various riding circumstances, riders of all speeds and abilities can aim to improve their balance.
learn more about center of gravity here:
https://brainly.com/question/20662235
#SPJ11
(240) One of the purposes of conductor overcurrent protection is to protect the conductors against excessive or dangerous heat.(True/False)
Conductor overcurrent protection is an essential safety measure in electrical systems to prevent overheating and potential fire hazards caused by excessive current flow. Therefore, it is true.
Here are some additional points about conductor overcurrent protection:
The primary purpose of overcurrent protection is to prevent damage to the conductors and other electrical components by interrupting the flow of current when it exceeds safe levels.Overcurrent protection devices such as fuses and circuit breakers are rated to trip at specific current levels and are chosen based on the size and capacity of the conductors they are protecting.Overcurrent protection devices should be properly coordinated to ensure that the device closest to the fault opens first, minimizing the amount of time that the faulted circuit is without power.This type of protection is achieved by the use of fuses or circuit breakers, which are designed to interrupt the flow of current when it exceeds a certain limit.
Learn More About overcurrent
https://brainly.com/question/30432230
#SPJ11
To find the correction factor for situation where four or more current carrying conductors are bundled together, consult Table _____.
To find the correction factor for a situation where four or more current carrying conductors are bundled together, consult Table 310.15(B)(3)(a) in the National Electrical Code (NEC).
This table provides adjustment factors for ambient temperature, conductor size, and number of conductors in a raceway or cable. The correction factor is used to adjust the ampacity of the conductors to account for the increased heat generated by the bundled conductors.
To find the correction factor for a situation where four or more current-carrying conductors are bundled together, consult Table 310.15(B)(3)(a).
To know more about Factor click here .
brainly.com/question/14209188
#SPJ11
Conductors in Parallel(310-10(H)(1)(Table 250-122): What are the conductors required for a 250 ampere feeder paralleled in two raceways?
The also recommended to consult a licensed electrician and comply with any local codes and regulations that may apply to the specific installation.
Why will be the conductors required for a 250 ampere feeder paralleled?To determine the conductors required for a 250 ampere feeder that is paralleled in two raceways, we need to consult the [tex]NEC[/tex] (National Electrical Code) Table 310.16, which provides ampacity values for various types and sizes of conductors.
Assuming the raceways are located in the same area and under the same conditions, we can parallel the conductors in accordance with the [tex]NEC 310.10(H)(1)[/tex] requirements.
This means that each parallel conductor must have the same length, be the same size, and be made of the same material.
Based on [tex]NEC[/tex] Table 250.122, we can use two parallel sets of 4/0 AWG conductors, which have an ampacity of 230 amps each.
Therefore, two sets of 4/0 AWG conductors in parallel would provide a total ampacity of 460 amps, which is well above the required 250 ampere feeder size.
It is important to note that this answer assumes that the installation complies with all other applicable [tex]NEC[/tex] requirements, such as those related to raceway fill, grounding, and overcurrent protection.
Learn more about licensed electrician
brainly.com/question/3449056
#SPJ11
charges move through the circuit from one plate to the other until both plates areuncharged.
The movement of charges from one plate to the other in a capacitor is a fundamental process that underlies many electronic devices and applications.
When a capacitor is connected to a circuit, charges begin to flow from one plate to the other until both plates reach the same potential and the capacitor becomes fully charged.
This process involves the movement of electrons, which are negatively charged particles, from one plate to the other.
Initially, the capacitor is uncharged, and the plates have an equal number of positive and negative charges.
When a voltage is applied to the capacitor, electrons begin to flow from the negative plate to the positive plate, creating an electric field between the two plates. This electric field stores energy in the capacitor, which can be released later when the capacitor is discharged.
If the voltage across the capacitor is removed, the capacitor will retain its charge and will discharge slowly over time as the electrons flow back from the negative plate to the positive plate.
This discharge process can be used in various applications, such as in flash photography, where a capacitor is charged rapidly and then discharged quickly to produce a bright flash of light.
For similar question on capacitor
https://brainly.com/question/13578522
#SPJ11
Question 3 Marks: 1 In practice, exposure to all ionizing radiation is controlled by the use of shields of lead.Choose one answer. a. True b. False
True, exposure to all ionizing radiation is controlled by the use of shields of lead.
Ionizing radiation is a form of energy that acts by removing electrons from atoms and molecules of materials that include air, water, and living tissue. Ionizing radiation can travel unseen and pass through these materials. Ionizing radiation, including nuclear radiation, consists of subatomic particles or electromagnetic waves that have sufficient energy to ionize atoms or molecules by detaching electrons from them.
Learn more about electrons here: https://brainly.com/question/1255220
#SPJ11
Who was the first person to suggest that the Earth orbited the sun?
The ancient Greek astronomer Aristarchus of Samos was the first person to suggest that the Earth orbited the sun, around 250 BCE.
Aristarchus of Samos was an ancient Greek astronomer and mathematician who lived from 310 BCE to 230 BCE. He was the first person to suggest that the Earth orbited the sun, rather than the other way around, as was commonly believed at the time. Aristarchus made this suggestion based on observations of the positions of the stars and planets, and his belief that the sun was much larger than the Earth, which made it more plausible that the Earth would orbit the sun rather than the other way around. Despite his groundbreaking theory, it was not widely accepted until much later, with the work of Nicolaus Copernicus in the 16th century.
Learn more about Greek astronomer here:
https://brainly.com/question/30283982
#SPJ11
3.) Convert the angle 4.4 radians in units of revolutions
A.) 0.637 rev
B.) 0.700 rev
C.) 0.766 rev
D.) 0.770 rev
E.) 0.777 rev
The angle of 4.4 radians in units of revolutions B.) 0.700 rev
To convert the angle 4.4 radians to units of revolutions, follow these steps:
1. Recall the relationship between radians and revolutions: 1 revolution = 2π radians.
2. Divide the given angle (in radians) by the radians per revolution (2π) to find the number of revolutions.
Here's the calculation:
4.4 radians / (2π radians/revolution) ≈ 4.4 / 6.283 ≈ 0.700 revolutions
So, the correct answer is:
B.) 0.700 rev
To explain further, imagine that you are walking around in a circle with a circumference of 1 unit. If you walk all the way around the circle and end up where you started, you have completed one revolution. Now imagine that you are walking along an arc of the circle that measures 4.4 units in length. If the circle has a circumference of 2π units, then the arc you are walking along is 4.4/2π of the circle's circumference. This fraction represents the fraction of a revolution that you have completed. To find the decimal value of this fraction, we divide 4.4 by 2π, which gives us 0.700. Therefore, the angle of 4.4 radians is equivalent to 0.700 revolutions.
To learn more about the angle, refer:-
https://brainly.com/question/28451077
#SPJ11
What information must be on a warming tag attached to a locked-out switch?
a. Directions for removing the tag
b. Name of the nearest physician to call in case of an emergency
c. Signature of the person who locked out the switch and who will remove it
d. Time to unlock the switch
A warning tag attached to a locked-out switch should contain the following information: c. Signature of the person who locked out the switch and who will remove it. This ensures proper identification and responsibility for the lockout process, promoting safety and accountability in the workplace.
A warming tag is a type of tag that is attached to a locked-out switch. According to the Occupational Safety and Health Administration (OSHA), a warming tag attached to a locked-out switch should contain the signature of the person who locked out the switch and who will remove it.
Find out more about warning tag
brainly.com/question/28097783
#SPJ11
HELP 100 POINTS Why don't birds get electrocuted when they land on an electric wire?
Answer: There are not able to be electricity
Explanation: Essentially, this means that the electricity is able to pass through the birds without damaging them.
2. A 100Ω, 300Ω, and 200Ω resistor are all connected in parallel. What is the resistance?
When resistors are connected in parallel, the total resistance is calculated as:
1/R(total) = 1/R(1) + 1/R(2) + 1/R(3) + ...
So for this question, we can plug in the values:
1/R(total) = 1/100 + 1/300 + 1/200
1/R(total) = 0.01 + 0.003333 + 0.005
1/R(total) = 0.019333
R(total) = 1/0.019333
R(total) = 51.67Ω
The electrical resistance of an object is a measure of its opposition to the flow of electric current. Its reciprocal quantity is electrical conductance, measuring the ease with which an electric current passes. Electrical resistance shares some conceptual parallels with mechanical friction. The SI unit of electrical resistance is the ohm (Ω), while electrical conductance is measured in siemens (S) (formerly called the 'mho' and then represented by ℧).
To know more about measure please vist :-
https://brainly.com/question/4725561
#SPJ11
15) How are interstellar bubbles made? A) by the collapse of a gas cloud to form stars B) by planetary nebulae from low-mass stars C) by the winds of massive stars and supernovae D) by collisions between galaxies E) by the rapidly rotating magnetic fields of pulsars
Interstellar bubbles are made by the winds of massive stars and supernovae.
These massive stars and supernovae release energy in the form of hot gas and high-speed particles. This energy blows away the surrounding gas and creates a bubble-like structure. Over time, the bubble expands and can become visible as a bright region in the interstellar medium.
When massive stars are born, they emit intense winds that blow away the surrounding gas and dust. As they age and eventually die in a supernova explosion, they release even more energy into the surrounding space, creating shock waves that sweep up the surrounding material into a bubble-shaped structure.
The energy released in these events can also cause the gas within the bubble to ionize and become hot, creating a phenomenon known as an HII region.
Therefore the correct answer is option C) by the winds of massive stars and supernovae.
To learn more about Interstellar bubbles, refer:-
https://brainly.com/question/29642617
#SPJ11
a thermal radiator is an object that group of answer choices is characterized by multiple temperatures. emits a discrete spectrum. emits all wavelengths. emits one wavelength is characterized by one temperature.
The statement "a thermal radiator is an object that is characterized by multiple temperatures" is not entirely accurate. A thermal radiator is an object that emits radiation at various wavelengths and intensities, and its emission spectrum is determined by its temperature.
However, the temperature of the radiator itself is not necessarily multiple, it may have a single temperature. So, to answer your question, the correct option would be "emits a discrete spectrum" as a thermal radiator emits radiation at specific wavelengths determined by its temperature, and this emission spectrum can be discrete or continuous depending on the radiator's characteristics.
Spectrum is produced when matter interacts with EMR. Using Bohr's hydrogen spectrum, we can comprehend both spectra. Let's examine the hydrogen spectrum proposed by Bohr to see what it says. According to this, absorption occurs when an electron gains energy and goes from one energy level to another (from lower to higher). Several spectral lines are emitted by the electrons as they transition from the excited state back to the ground state. The term "emission spectrum" refers to this spectrum.
Learn more about emission spectrum here
https://brainly.com/question/27268130
#SPJ11
(315-15(B)(3a) The ampacity of six current-carrying No. 4/0 XHHW aluminum conductors installed in a ground floor slab (wet location) is _____.
Option 4. The ampacity of six current-carrying No. 4/0 XHHW aluminum conductors installed in a ground floor slab (wet location) is 210 A.
The temperature rectification consider for guide ampacity this not set in stone by deducting the reference temperature of 30°C from the surrounding temperature of 38.9°C, bringing about a temperature revision element of 1.08.
Expecting a circuit voltage of 480V, the ampacity of six current-conveying 4/0 XHHW aluminum guides in a wet area can be determined involving the NEC rules for channel fill and guide ampacity. With a guide protection temperature rating of 90°C, the ampacity rating of every guide is 205A. Taking into account the change factor for six current-conveying guides, which is 0.8, the last ampacity of the six guides is determined as follows:
(205A x 6 guides x 0.8 change factor) x 1.08 temperature rectification factor = 839A
In this manner, the straightforward reply to the inquiry is 4. 210 A (gathered together to the closest entire number), which addresses the ampacity of six current-conveying 4/0 XHHW aluminum guides introduced in a ground floor chunk (wet area) with a normal encompassing temperature of 102°F and a base protection temperature rating of 90°C.
To learn more about ampacity and conductors, refer:
https://brainly.com/question/29855050
#SPJ4
The complete question is:
Temperature is expected to be 102°F The temperature correct-A 2 TW conductor is installed in a location where the ambient ion factor for conductor ampacity in this location is the ambient temperature is 71°C, the minimum insulation 69 Ambient. The ampacity of six current-carrying 4/0 XHHW aluminum conductors installed in a ground floor slab (wet location) is 1. 135 A 2. 144 A 3. 185 A 4. 210 A
Question 7 Marks: 1 The frequency of a sound determines its pitch.Choose one answer. a. True b. False
The correct answer is a. True.
Frequency refers to the number of vibrations per second of a sound wave. The higher the frequency, the higher the pitch of the sound. Therefore, the frequency of a sound wave directly determines its pitch. A sound with a higher frequency will have a higher pitch, and a sound with a lower frequency will have a lower pitch.
The frequency of a sound determines its pitch. Pitch is the perception of how high or low a sound is to the human ear. A higher frequency results in a higher pitch, while a lower frequency corresponds to a lower pitch.
To learn more about pitch : brainly.com/question/27128408
#SPJ11
Which concept was NOT a part of Kepler's Laws of Planetary Motion?
a.All planetary orbits are ellipses.
b.The square of the planet's period is equal to the cube of its average distance.
c.Epicycles are needed to explain the varying brightnesses of the planets.
d.The line that connects the Sun to Mercury sweeps out equal areas during equal intervals of time.
e.A planet must move fastest in its orbit at perihelion.
The concept that was NOT a part of Kepler's Laws of Planetary Motion is c) Epicycles are needed to explain the varying brightnesses of the planets.
Kepler's Laws of Planetary Motion were formulated by the German astronomer Johannes Kepler in the early 17th century, based on the observations of his mentor Tycho Brahe. These laws describe the motion of planets around the Sun and are considered to be among the most important discoveries in the history of astronomy.
Kepler's first law states that all planetary orbits are ellipses with the Sun at one of the foci. The second law states that the line connecting a planet to the Sun sweeps out equal areas at equal times, meaning that a planet moves faster when it is closer to the Sun. The third law states that the square of a planet's orbital period is proportional to the cube of its average distance from the Sun.
Epicycles, on the other hand, were used by ancient astronomers to explain the motion of planets in the sky. Epicycles were small circles that were added to the orbit of a planet to account for its apparent retrograde motion. Kepler's laws did not require the use of epicycles to explain the motion of planets.
Find out more about Kepler's first law
at brainly.com/question/30733348
#SPJ11
(300-19, Table 300-19(A)) A 100 foot vertical run of No. 4/0 copper requires the conductors to be supported at _____ locations.
According to Table 300-19(A) in the National Electrical Code (NEC), a 100 foot vertical run of No. 4/0 copper conductors requires the conductors to be supported at a minimum of 7 locations.
At least seven support locations are required for a 100 foot vertical run of No. 4/0 copper. The support locations should be spaced no more than 20 feet apart and should be supported with a combination of rigid metal conduit (RMC), intermediate metal conduit (IMC), conduit bodies, or cable trays. In addition, the support locations must be able to support the weight of the conductors as well as any environmental factors, such as wind loading, that could affect the support structure.
To learn more about conductors click here https://brainly.com/question/13495387
#SPJ11
mc qu. 13 after using the barter system, it was... after using the barter system, it was decided that a simpler medium of exchange needed to take place, and the result was to
In the wake of taking on the trade framework, it was resolved that a less complex type of trade was required.
Prompting the decision of a solitary decent that could be openly traded for some other great with the assent of the gatherings.
What is a Barter system ?The term "barter," which comes from the Latin word "baretor," refers to a method of exchanging goods and services between two parties without the use of money.
The bartering system most likely originated with Mesopotamian tribes around 6000 BC. The Phoenicians saw how it was done and adopted it into their culture. These ancient people exchanged products for the food, instruments, and flavors they required.
Under this system, there is no imbalance in trade or a lack of foreign currency. A barter system does not produce the waste that occurs in a monetary economy. because there are neither too many nor too few products.
Learn more about Barter system:
brainly.com/question/14283220
#SPJ4
Adjust the frequency to 100% so the bulb is always "on."With the electromagnet still just to the left of the pickup coil, how does the average brightness of the light bulb depend on the number of loops of the pickup coil? (You can change the number of loops in the Pickup Coil properties box at bottom right.)
Adjusting the frequency to 100% will cause the bulb to always be on because the high frequency will not allow the bulb to turn off.
As for the average brightness of the light bulb with the electromagnet to the left of the pickup coil, it depends on the number of loops of the pickup coil. The more loops there are, the higher the brightness will be because there is more electromagnetic energy being transferred to the coil, which in turn produces a stronger magnetic field that powers the bulb. So, increasing the number of loops in the Pickup Coil properties box will result in a brighter light bulb. The average brightness of the light bulb will depend on the number of loops of the pickup coil in that the more loops there are, the greater the output of the coil.
To learn more about frequency click here https://brainly.com/question/22548127
#SPJ11
Rf value (ratio to front)
Rf value, or ratio to front value, is a numerical representation of the distance traveled by a compound in relation to the distance traveled by the solvent front in a thin layer chromatography experiment.
It is calculated by dividing the distance traveled by the compound by the distance traveled by the solvent front. The Rf value is a useful tool in identifying and comparing compounds, as it is characteristic of each compound and can be used to distinguish between them.
Rf value, also known as the ratio to the front, is a term used in chromatography. It represents the distance a component travels on the chromatography medium relative to the distance traveled by the solvent front. It is calculated by dividing the distance the component traveled by the distance the solvent front traveled. This value helps in identifying components in a mixture based on their relative movement through the chromatography medium.
To learn more about chromatography visit;
brainly.com/question/30907934
#SPJ11
A ball at the end of a string is swinging as a simple pendulum. Assuming no loss in energy due to friction, we can say for the ball that
A. the potential energy is maximum at the lowest position of the ball.
B. the potential energy is maximum where the kinetic energy is a minimum.
C. the potential energy is maximum where the kinetic energy is maximum.
D. the kinetic energy is maximum at each end of the motion.
Answer:
Only (B) is correct:
PE + KE = constant
When Potential Energy is a maximum., the KE is zero
Also, PE depends on the height of the ball
a family ice show is held at an enclosed arena. the skaters perform to music with level 91.0 db. this level is too loud for your baby, who yells at 86.0 db (a) what total sound intensity engulfs you?
The total intensity engulfing of sound produce by Music have loudness is 91.0 db is approximately 91.2 dB.
To find the total sound intensity, you need to combine the intensity levels of the music (91.0 dB) and the baby yelling (86.0 dB).
1. Convert the decibel levels to intensity values using the formula: I = 10^(dB/10), where I is the intensity and dB is the decibel level.
For the music:
[tex]I_{(music)} = 10^{(91.0/10)} = 10^{9}[/tex]
1 For the baby:[tex]I_{baby} = 10^{(86.0/10)} = 10^{8.62}[/tex]
Add the intensities together to get the total intensity:
[tex]I_{(total)} = I_{(music)} + I_{(baby)}[/tex]3. Convert the total intensity back to decibels using the formula:
[tex]dB = 10 * log10(I) dB_{total }[/tex]
[tex]= 10 * log10(I_{total})[/tex]
Following these
steps:1.[tex]I_{music} = 10^{9.1} = 1,258,925 I_{baby} = 10^{8.6} = 398,1072.[/tex]
[tex]I_{(total)} = 1,258,925 + 398,107 = 1,657,0323.[/tex]
[tex]dB_{total} = 10 * log10(1,657,032) =91.2 dB[/tex]
So, the total sound intensity engulfing you is approximately 91.2 dB.
To know more about intensity Visit:
https://brainly.com/question/17583145
#SPJ11
Terminal Rating(110-14(C)(1): What size THHN conductor is required for a 70 ampere branch circuit if the circuit breaker and equipment is listed for 75 degrees C terminals and the load does not exceed 65 ampere?
According to the NEC code 110-14(C)(1), for a 70 ampere branch circuit with equipment and circuit breaker listed for 75 degrees C terminals and a load not exceeding 65 ampere, the minimum required size of THHN conductor would be 4 AWG.
For a 70-ampere branch circuit with 75-degree C terminals and a load not exceeding 65 ampere, you would need a 4 AWG THHN conductor. This conductor size is suitable for up to 85 amperes at 75-degree C terminals, providing ample capacity for your specified requirements.
The NEC code 110-14(C)(1) states that the minimum required size of THHN conductor for a 70 ampere branch circuit with equipment and a circuit breaker designated for 75 degrees C terminals and a load not exceeding 65 ampere would be 4 AWG.
To know more about THHN conductor click here:
https://brainly.com/question/31197467
#SPJ11