The temperature rise of the iron is 13.33°C
How to calculate temperature in calorimetry?Calorimetry is the science of measuring the heat absorbed or evolved during the course of a chemical reaction or change of state.
The heat gained or released during a calorimetry procedure can be calculated as follows:
Q = mc∆T
Where;
Q = quantity of heat (J)m = massc = specific heat capacity∆T = change in temperatureAccording to this question, a 5kg block of iron with a specific heat capacity of 450 J/kg °C recieves 0.03 MJ of energy. The change in temperature can be calculated as follows:
30,000J = 5 × 450 × ∆T
30000 = 2250∆T
∆T = 30000 ÷ 2250
∆T = 13.33°C
Therefore, 13.33°C is the temperature rise.
Learn more about temperature at: https://brainly.com/question/28992424
#SPJ1
With rivers and streams, the movement of rock material from one place to another is called
Answer:
Erosion is the removal and transportation of rock or soil. Erosion can move sediment through water, ice, or wind. Water can wash sediment, such as gravel or pebbles, down from a creek, into a river, and eventually to that river's delta. Hope this helps.
A golfer is enjoying a day out on the links.
What maximum height will a 329.7 m drive
reach if it is launched at an angle of 22.0
to the ground? The acceleration due to gravity
is 9.81 m/s^2.
Answer in units of m.
The maximum height of the drive be 33.30 m.
What is projectile potion?When a particle is hurled obliquely near the surface of the earth, it travels along a curved path while accelerating continuously in the direction of the planet's center (we assume the particle stays close to the surface of the globe). Such a particle's motion is known as projectile motion, and its route is referred to as a projectile.
Given that:
Range: R = 329.7 m
Angle of projection = 22.0°
Acceleration due to gravity; g= 9.81 m/s^2.
So, maximum height: H = 1/4 R tan22.0° m
= 1/4 × 329.7 × tan 22.0°
= 33.30 m.
Hence, maximum height of the drive be 33.30 m.
Learn more about projectile motion here:
https://brainly.com/question/11049671
#SPJ1
what can you conclude about the time it takes a hollow cylinder and a solid cylinder to roll down an incline?
The fact that a solid cylinder rolls down a hill more quickly than a hollow one has been demonstrated above. This is as a result of their inertial moments.
What is hollow cylinder?A cylinder that is hollow from the inside out and has a discrepancy between its internal and external radii is referred to as a hollow cylinder. The base of the hollow cylinder is shaped like an annular ring.. So the hollow cylinder's bottom resembles a zone enclosed by two concentric rings.
What Is the Volume of a Hollow Cylinder and its formula?The area encircled by the shape in a three-dimensional plane is referred to as the volume of a hollow cylinder. A hollow cylinder is one that has a discrepancy between the internal and external radius and is empty on the inside. In other terms, it is a cylindrical shape with some thickness at the edges and no inside.
Because the formulas for calculating the total surface area (TSA) of a cylinder and a hollow cylinder are almost identical, use caution. TSA of a cylinder is equal to 2 rh plus 2 r2, or the surface area of the cylinder plus the area of 2 circles.
To know more about Cylinder visit:
https://brainly.com/question/13975091
#SPJ4
what is the primary function of a refrigerant distributor at the outlet of a thermostatic expansion valve? what is the primary function of a refrigerant distributor at the outlet of a thermostatic expansion valve? allow the evaporator to operate with a proper superheat feed the evaporator sufficient liquid to control the leaving air temperature decrease the pressure drop across the evaporator coil evenly feed each evaporator circuit
The distributor's job is to distribute refrigerant equally throughout the circuiting of the evaporator. As the expansion valve's larger nozzle opens, the distributor maintains a constant flow rate.
What is the thermostatic expansion valve's main purpose?An essential piece of machinery in the HVAC sector is the Thermal Expansion Valve (TXV). The valve's function is to regulate the flow of refrigerant into the evaporator section. In this manner, it regulates the discrepancy between superheat and the refrigerant temperature that is currently present at the evaporator outlet.
What is the operation of a thermal expansion relief valve?The thermal expansion relief valve works similarly to an expansion tank by taking up the extra pressure that thermal expansion causes in the plumbing system.
Learn more about velocity here:
https://brainly.com/question/18084516
#SPJ4
A 5.0 kg ball is launched with a speed of 2.0 m/s. Find momentum of the ball
Answer:
10 kgm/s
Explanation:
p = m*v (momentum = mass * velocity)
p = 5 kg * 2 m/s
p = 10 kgm/s
Answer:
10 kg. m/s
Explanation:
[tex]p = m \times v[/tex]
p = 5 * 2
= 10 kg.m/s
ppA hollow plastic ball is projected into the air.
There is significant air resistance opposing the
ball's motion, so the magnitude of the ball's
acceleration is not equal to g. At time t, the ball is
moving up and to the right at an angle of 45° to
the horizontal, as shown above. Which of the
following best shows the magnitude a and the
direction of the ball's acceleration at time/?
a > g , is the best shows the magnitude a and the direction of the ball's acceleration at time.
What is acceleration?Acceleration is the rate at which the speed and direction of a moving object change over time. A point or object travelling in a straight path is accelerated if it accelerates or decelerates. Even if the speed is constant, motion on a circle is accelerated because the direction is always changing.
Given data
The velocity of the ball is: V
The angle of velocity with the horizontal is (θ) = 45
The acceleration of the ball is: a
The acceleration due to gravity is: g
When the hollow ball is projected into the air, air resistance will act on the ball that will slow down the ball's motion. Therefore the velocity direction is opposite to the reducing force. The reducing force relates to the opposite to the acceleration of the hollow ball.
F(delaying) ∝ -VF(delaying) ∝ m×a(r)×F(delaying) ∝ a(r)
Here m is the mass of the hollow ball.
The force of gravity on the ball which is acting downward given as:
F(gravity) ∝ g
So, a > g
Correct option: (B)
To know more about acceleration refer to:
https://brainly.com/question/460763
#SPJ1
if the magnetic field is directed toward the north and a positively charged particle is moving toward the east, what is the direction of the magnetic force on the particle?
In a magnetic field, a positively charged particle is traveling northward. The particle's magnetic field is oriented northeastward.
What direction is the force pulling on a positively charged particle traveling west to east in a downwardly-directed magnetic field?The motion of the -particle is parallel to the direction of the stream (east to west). The magnetic field is pointing into the paper. Fleming's left-hand rule is used to direct the force into the page south as a result. Consequently, the particle will be diverted southward.
Magnetic north is it positive or negative?Positive and negative poles are present and are found at the ends of the magnet. In contrast to electric charges, the poles can be separated since the north pole has a positive charge and the south pole a negative charge.
to know more about the magnetic field here:
brainly.com/question/14848188
#SPJ4
A box is on the floor. The box is not moving.
Draw a labelled force diagram to show all the forces acting on the box.
Answer: The floor has more friction than the force given to the box for movement.
Explanation:
The labeled diagram is given below.
For more about Friction:
https://brainly.in/question/1182128
The forces acting on the block at rest are the normal force (N), weight of the block (W) and the force of friction (F).
What are the forces acting on the block?When a block is at rest on a horizontal floor, several forces are acting on it.
These forces are in equilibrium, meaning they balance each other out and result in zero net force, allowing the block to remain stationary.
The main forces acting on the block are:
Weight: The force of gravity pulls the block downward toward the center of the Earth.
Normal Force: The normal force is the force exerted by a surface to support the weight of an object resting on it.
Frictional Force: If the block is not on a perfectly frictionless surface, there will be a frictional force opposing the tendency of the block to slide.
Learn more about force diagram here: https://brainly.com/question/3624253
#SPJ2
HELP PLS
HELP PLS
HELP PLS
HELP PLS
HELP PLS
HELP PLS
HELP PLS
HELP PLS
Answer: 6.0 m/s/s
Explanation: If the net force acting on an object is halved, the acceleration of the object will also be halved. Therefore, if the object has an acceleration of 12.0 m/s/s and the net force acting on it is halved, the new acceleration of the object would be 12.0 m/s/s / 2 = 6.0 m/s/s.
Water molecules are positive on one end, negative on the other. Predict what a negatively charged balloon will do when placed close to a stream of water.
The positive charged particles in the water will move the water towards the negatively charged balloon which is prediction which will happen when they are placed close to each other.
What is Attraction?This is referred top as a type of force that pulls the body near it and we should also note that like poles repel while unlike poles attract.
Since positive and negative charges are attracted to each other, then the positive charged particles in the water will move the water towards the negatively charged balloon which is therefore the reason why it was chosen as the correct choice.
Read more about Attraction here https://brainly.com/question/25624188
#SPJ1
A large, moving truck crashes into a small parked car. How do the magnitudes of the impulses and the forces on each vehicle compare during the collision?
A. The truck experiences less force and less impulse.
B. The truck experiences equal force and equal impulse.
C. The truck experiences less force but more impulse.
D. The truck experiences more force but less impulse.
The magnitudes of the impulses and the forces on each vehicle are the truck experiences equal force and equal impulse.
Newton's third law dictates that the forces on the car and the truck are equal but opposite in direction.
So, the force on the truck is equal to the force on the car.
Ft = Fc
where, Fc is the force on the car
Ft is the force on the truck
Impulse is nothing but force multiplied by time and the time of contact is same for both the vehicles. So, the impulse is same in magnitude for the two vehicles.
Impulse can also be written as change in momentum. So, the change in momentum is also equal for both the vehicles.
Thus, force on the truck is equal to the force on the car. And the impulse on the truck is equal to the impulse on the car.
To know more about forces:
https://brainly.com/question/13571634
#SPJ4
Explain why the car reaches a top speed even though the thrust force remains constant
at 3500 N.
Since, the velocity not only depends on the force but also on the amount of time that has passed since the motion started, therefore, the car reaches a top speed even though the thrust force remains constant.
What is force?
In order to move a body of mass [m] with an acceleration of [a] m/s², a force of magnitude equal to the product of body's mass and the required acceleration is needed. Mathematically -
F = ma
F = m {a[x] + a[y] + a[z]}
F = ma[x] + ma[y] + ma[z] {Vector form}
We have a car reaches a top speed even though the thrust force remains constant at 3500 N.
We know the formula for force as -
F = ma
F = m(dv/dt)
dv/dt = F/m
dv = (F/m)dt
∫dv = ∫(F/m)dt
v = (F/m)t
v = kt
v [tex]\alpha[/tex] t
It can be seen that the velocity not only depends on the force but also on the amount of time that has passed since the motion started.
Therefore, since, the velocity not only depends on the force but also on the amount of time that has passed since the motion started, therefore, the car reaches a top speed even though the thrust force remains constant.
To solve more questions on force, visit the link below-
brainly.com/question/1318725
#SPJ1
write the balanced nuclear equation for formation of 81kr through electron capture.
The balanced nuclear equations for formation of ⁸¹ Kr through electron capture is (81,37)Rb + (0,-1)e > (81,36)Kr
Nuclear equations represent the reactants and products in radioactive decay, nuclear fission, or nuclear fusion. Instead of chemical equations showing that different numbers of elements are conserved in a reaction, atomic mass and proton number are conserved in a nuclear reaction.
A nuclear reaction is generally expressed by a nuclear equation, which has the general form, where T is the target nucleus, B is the bombarding particle, R is the residual product nucleus, and E is the ejected particle, and Ai and Zi (where I = 1, 2, 3, 4) are the mass number and atomic number, respectively. Finding a well balanced equation is critical for understanding nuclear reactions. Balanced nuclear equations provide excellent information about the energy released in nuclear reactions. Balancing the nuclear equation requires equating the total atomic number as well as the total mass number before and after the reaction using the rules of atomic number and mass number conservation in a nuclear reaction.To know more about nuclear equations,
https://brainly.com/question/28305283
#SPJ4
Problem 4: A uniform flat disk of radius R and mass 2M is pivoted at point P A point mass of 1/2 M is attached to the edge of the disk 2M 2 M Part (a) Calculate the moment of inertia ICM of the disk (without the point mass) with respect t0 the central axis of the disk in terms of M and R. Expression IcM Select from the variables below t0 write your expression. Note that all variables may not be required. 4,0, 0,4,d,gh,ijk M,P,R,$, Part (b) Calculate the moment of inertia [p of the disk (without the point mass) with respect to point P in terms of M and R. Expression Select from the variables below to write your expression_ Note that all variables may not be required: a,B,0,a,d,gh,ij,k M,PRS Part (c) Calculate the total moment of inertia [rof the disk with the point mass with respect to point P in terms of M and R Expression It Select from the variables below t0 write your expression Note that all variables may not be required: 4,0, 0,#,d,gh,ij,k M,P,R,$,'
From the case we know that:
The moment of inertia Icm of the uniform flat disk witout the point mass is Icm = MR². The moment of inerta with respect to point P on the disk without the point mass is Ip = 3MR². The total moment of inertia (of the disk with the point mass with respect to point P) is I total = 5MR².Please refer to the image below.
We know from the case, that:
m = 2M
r = R
m2 = 1/2M
distance between the center of mass to point P = p = R
Distance of the point mass to point P = d = 2R
We know that the moment of inertia for an uniform flat disk is 1/2mr². Then the moment of inertia for the uniform flat disk is:
Icm = 1/2mr²
Icm = 1/2(2M)(R²)
Icm = MR² ... (i)
Next, we will find the moment of inertia of the disk with respect to point P. We know that point P is positioned at the arc of the disk. Hence:
Ip = Icm + mp²
Ip = MR² + (2M)R²
Ip = 3MR² ... (ii)
Then, the total moment of inertia of the disk with the point mass is:
I total = Ip + I mass
I total = 3MR² + (1/2M)(2R)²
I total = 3MR² + 2MR²
I total = 5MR² ... (iii)
Learn more about Uniform Flat Disk here: https://brainly.com/question/14595971
#SPJ4
how does the habitable zone around a star of spectral type g compare to that around a star of spectral type m ?
The Answer is "It is Larger". This is how the habitable zone around a star of spectral type G compare to that around a star of spectral type M is.
What is an M spectral star?
An M-type star is within the M-class, a spectral class indicating stars with very weak hydrogen absorption lines and with molecular lines, a surface temperature in the 2400-3700 K range and a red color. M spectral stars are coolest and most common stars in the Universe. The spectral energy distribution peaks in the near infrared.
I suppose the question is :
How does the habitable zone around a star of spectral type G compare to that around a star of spectral type M?
1. It is larger.
2. It is hotter.
3. It is closer to its star.
To know more about Star of Spectral Type : https://brainly.com/question/28209561
#SPJ4
1. Indicate the charge carried by the following atomic particles:
a. Proton: _?_
b. Neutron: _?_
c. Electron: _?_
a. Proton carries positive electrical charge.
b. Neutron are neutral with no electrical charge
c. Electron carries negative electrical charge.
According to Rutherford's atomic model the electrons are negatively charged which revolves around the nucleus of the atom, in circular paths named as orbits.
Proton, the positive charge is concentrated in the center known as nucleus.
Later, scientists discover that in the nucleus of atom there is one neutral particle called neutron. Protons and Neutrons together are called nucleons.
To learn more about electron, proton and neutron,
https://brainly.com/question/1412226
https://brainly.com/question/28867252
a dog walks 0.64 km due north. he then runs due west to an ice cream stand. if the magnitude of the dog's total displacement vector is 0.91 km, what is the magnitude of the dog's displacement vector in the due west direction?
The magnitude of dog's displacement vector in the due west direction is 0.65 km.
It is given that, a dog walks 0.64km due north.
It is also given that the magnitude of dog's total displacement is 0.91 km.
The magnitude of dog's displacement vector in the due west direction can be found by using Pythagoras theorem.
It is mathematically represented as, c² = a² + b²
Given, c = 0.91 km
a = 0.64 km
b =?
Making b as subject, we have,
b² = c² - a²
b = √(c² - a²) = √(0.91² - 0.64²) = 0.65 km
Thus, the magnitude of dog's displacement vector in the due west direction is 0.65 km.
To know more about Pythagoras theorem:
https://brainly.com/question/343682
#SPJ4
by which primary heat transfer mechanism does one end of a steel rod become hot when the other end is placed in a flame?
Heat transfer by convection occurs when a fluid (such as air or water) is moving. The movement of a material carrier distinguishes conduction from convection, which is the transfer of thermal energy by the movement of hot fluid (as opposed to making other material hot by wiggling atoms).
Usually, changes in density cause this motion to happen. Because warmer particles are less dense, they will travel to areas where it is cooler because they are less dense, whereas cooler particles will move to areas where it is warmer. Until balance is attained, the fluid will continue to move.Thermal energy can be exchanged between objects by a variety of techniques, all of which are based on the fundamental idea that heat and kinetic energy both prefer equilibrium and similar energy states. Conduction, convection, and radiant heat (commonly referred to as radiation, but it's a more comprehensive phrase that includes many other processes) are the three main ways that heat can transfer.
To know more about Heat transfer
https://brainly.com/question/7873010
#SPJ4
based on counting the number of galaxies in a small patch of the sky and multiplying by the number of such patches needed to cover the entire sky, the total number of galaxies in the observable universe is estimated to be approximately:_____.
Answer:
two trillion galaxies
Explanation:
If we made the most straightforward estimate using today's best technology, we'd state there are 170 billion galaxies in our Universe. But we know more than that, and our modern estimate is even grander
When pulled, stretchy objects such as rubber bands exert elastic force. Gently hold one end of the rubber band and pull on the other end. You will feel the rubber band pulling back. How does the force exerted by the rubber band change as you increase its length? What do you observe?
Answer:
The force exerted by the rubber band will increase. This is because the restoring force (force which acts to bring a body back to its equilibrium state) always acts in opposite direction to the force which acts to pull the body from its equilibrium position. And as the distance increases the force increases as well.
Explanation:
A box of mass 50kg is pulled up from the hold of a ship with an acceleration of 1 meter per second square by a vertical rope attached to it. Find the tension in the rope.
Working as a seismologist, you find the epicenter of many earthquakes in a region. What features of earth's crust would you expect to find in this region?
Answer:
Explanation:
As a seismologist studying earthquakes in a particular region, you might expect to find certain features of the earth's crust in that region that are indicative of tectonic activity. Some examples of these features include:
Fault lines: These are fractures in the earth's crust where two tectonic plates have moved relative to each other, often resulting in earthquakes when the movement is sudden and violent.
Folded mountain ranges: When tectonic plates collide, the resulting pressure can cause the earth's crust to fold and form mountain ranges.
Volcanoes: Many earthquakes occur in regions with volcanic activity, as the movement of magma beneath the earth's surface can cause the ground to shake.
Plate boundaries: The boundary between two tectonic plates is often a zone of high seismic activity, as the plates grind against each other and cause earthquakes.
Seismic gaps: Some areas along a fault line may have experienced few or no earthquakes in recent history, and are therefore considered "seismic gaps." These areas may be more prone to earthquakes in the future as the pressure builds up.
By studying these and other features of the earth's crust, you can gain a better understanding of the underlying tectonic processes that contribute to earthquakes in the region.
1. Can you use the change in temperature to predict how long it will take for thermal equilibrium to be reached? What equation would you use? What other variables would you need?
2. How does temperature affect the time it takes to reach thermal equilibrium?
3. Explain why it takes different amounts of time for thermal equilibrium to occur in each case.
PLEASE HElP I URGENTLY NEED THIS!!!!
A body is said to be in thermal equilibrium where all the system temperatures are the same.
What is thermal equilibrium?Take a well insulated beaker and pour water of known mass in it. Record its initial temperature.Place heated metal into the beaker and make sure that the beaker is tightly packed so that no heat escapes from the beaker.Record temperature of the beaker at different intervals and after temperature has become constant ( No heat is being gained) , note the final temperature In end we will check whether thermal equilibrium is established or not.heat lost by the metal = heat gained by water + heat gained by the beaker If you are working with closed systems, you need to know the mass of water, its initial temperature, the specific heat of the water (which is 1 cal / g °C), the mass of the environment with which the water is in contact, its initial temperature and the specific heat.A body is said to be in thermal equilibrium where all the system temperatures are the same. In this case, there will be no temperature gradient between the system and the environment.While, A body is said to be in thermodynamic equilibrium if all three requirements of equilibrium are met, i.e. mechanical equilibrium, chemical equilibrium and thermal equilibrium.To learn more about thermal equilibrium refer to:
https://brainly.com/question/9459470
#SPJ1
consider the following circuit. after leaving the switch at the position a for a long time, move the switch from a to b. there will be current oscillations.
Switch the switch from position a to position b after leaving it in position a for a while. Current oscillations are expected to be zero.
What defines oscillation?The regular to-and-fro oscillation of a Simple pendulum is referred to as its oscillatory motion. One oscillation of the a pendulum is defined as the motion of a bob starting from one end and returning to the other.
What is oscillation of a wave?An oscillating wave is one that moves back and forth on a regular, repeated basis. This oscillation may occur between extremes of force, amount, or position. Oscillations in waves can take many distinct forms.
To know more about oscillation visit:
brainly.com/question/29273618
#SPJ4
5 Forces of 25 N and 40 N act on an object in the directions shown
25N
40N
Which arrow shows the direction of the resultant force on the object?
K
B
Answer:
B
Explanation:
pls mark the brainliest
how wide must a narrow slit be if the first diffraction minimum occurs at ±12° with laser light of 633 nm?
The width of narrow slit will be 3 μm if the diffraction minima occurs with 633 nm wavelength.
The angular width of the central maximum is the angle between the two first order minima (on either side of the center).The diffraction formula's central maximum width is inversely related to the slit width. The central maximum widens as the slit width gets smaller, and gets narrower as it gets larger. From this behavior, it can be concluded that light bends more as the aperture's size decreases.Monochromatic light is passed through a single slit with a finite width in a single-slit experiment, and a similar pattern is seen on the screen. As we move farther from the central maximum in the single-slit diffraction pattern, compared to the double-slit diffraction pattern, the width and intensity decrease.Δ=2L/α
Δ=3 x 10⁻⁶m
=3micro meter.
To study more on Monochromatic light -
https://brainly.com/question/14896284
#SPJ4
When will you attract the sun more,
today at noon or tonight at midnight
remnants of volcanic activity on the asteroid vesta indicate that members of the asteroid belt
Remnants indicate that members of the asteroid belt occasionally grow large enough to become differentiated and geologically active.
The members of the asteroid belt were never part of one larger body. Instead, they formed by the same process of accretion that formed the rest of the planets.
Several of these asteroids accreted enough mass to cause internal heat, thus differentiating the body and allowing some volcanically altered rock to accumulate on their surfaces.
When asteroid leaves the asteroid belts, these asteroids may crash into a planet or moon or fling out of the solar system. Some of these asteroids have unusual orbits. This is because of Jupiter's gravity.
To know more about asteroid here
brainly.com/question/2826424
#SPJ4
A car drives 2 blocks north, then 3 blocks east, and finally 2 blocks south. What is the
displacement of the car?
A) 15 km
B) 3 km west
C) 3 km east
D) 7 km north
What will be the period of oscillation of a 12kg metallic bob attached to a spring, where the same pendulum takes 4 seconds for a bob of
mass 8kg attached to the spring?
The pendulum swings in one direction for 4 seconds in each direction, making a 15.9 m swing in one second.
What purposes serve pendulums?Instruments utilized in science, such as seismometers and accelerometers, also employ pendulums. They have a history of being used as length standards and gravimeters for measure an acceleration of gravity in geophysical surveys. The word "pendulum" is derived from the Latin word "pendulus," which means "hanging."
When you swing a pendulum, what happens?The gravity force will cause the swing to freely swing back and forth when it has been hoisted and released. The swing keeps swinging back and forth on its own until frictional (between the swing and the air, and between chains and the connection points) slows it down and ultimately causes it to stop.
To know more about pendulums visit:
https://brainly.com/question/29268528
#SPJ1