The layer of the TCP/IP model that provides the function of defining specifications for how signals are sent over connections is the A) Transport layer.
The Transport layer is a layer in the TCP/IP model that provides end-to-end communication between devices over a network. It is responsible for ensuring reliable and orderly delivery of data across the network by establishing and managing connections between devices.
One of the key functions of the Transport layer is to define specifications for how signals are sent over connections. Specifically, it determines the type of service required for a given data transfer, such as the reliability and speed of delivery, and how the data should be divided into smaller units, known as segments or packets.
So the correct answer is A.Transport.
Learn more about TCP/IP: https://brainly.com/question/14280351
#SPJ11
When a metal underground water pipe is used as a grounding electrode, the pipe shall be electronically continuous and in direct contact with the eart for at least _____ feet.
250.52(a)(1)
According to the National Electrical Code (NEC) 2021 edition, when a metal underground water pipe is used as a grounding electrode, the pipe shall be electrically continuous and in direct contact with the earth for at least 10 feet.
The purpose of this requirement is to ensure that the metal water pipe provides a low-resistance path to ground for electrical current in the event of a fault or surge in the electrical system. The 10-foot minimum length requirement helps to ensure that the metal water pipe is in good contact with the earth and can effectively dissipate any electrical energy that may be present. It is also important to note that the metal water pipe must be supplemented by additional grounding electrodes as necessary to meet the requirements of the NEC. These may include driven rods or plates, concrete-encased electrodes, or other approved grounding electrodes, depending on the specific circumstances of the installation.
Learn more about underground water here:
https://brainly.com/question/30025861
#SPJ11
Which three IP addresses are private? (choose three)
The three IP addresses that are private are 10.0.0.0, 172.16.0.0, and 192.168.0.0. These are reserved IP addresses that are not used for public internet communication and can only be used within a private network.
Public IP addresses, on the other hand, are used for internet communication and are unique to each device connected to the internet.
There are three IP address ranges that are considered private:
1. 10.0.0.0 to 10.255.255.255
2. 172.16.0.0 to 172.31.255.255
3. 192.168.0.0 to 192.168.255.255
These IP address ranges are reserved for private use within local networks and are not routable on the public internet.
Learn more on IP Addresses here :
brainly.com/question/30781274
#SPJ11
True or False? although inductive current lags inductive voltage by 90°, both waves have the same frequency.
The answer to the question: "True or False? although inductive current lags inductive voltage by 90°, both waves have the same frequency."
True, although inductive current lags inductive voltage by 90°, both waves have the same frequency.
Learn more about current lags: https://brainly.com/question/24858512
#SPJ11
Three way and four way switches shall be so wired that all switching is done only in the _______ circuit conductor.
404.2(a)
According to the National Electrical Code (NEC) 404.2(a), three-way and four-way switches shall be wired so that all switching is done only in the ungrounded (hot) circuit conductor. This means that the switched conductor, or the wire that is connected to the load being switched, should not be connected directly to any switch.
Instead, in a three-way switch configuration, two switches are used to control a single load. The two switches are connected to the ungrounded (hot) circuit conductor and a traveler wire, which carries the ungrounded (hot) circuit conductor between the switches. The load is then connected to the switched conductor, which is connected to one of the travelers.
In a four-way switch configuration, three or more switches are used to control a single load. In this case, the switches are connected to the ungrounded (hot) circuit conductor and two or more traveler wires, which carry the ungrounded (hot) circuit conductor between the switches. The load is then connected to the switched conductor, which is connected to one of the travelers.
By wiring the switches in this way, all switching is done in the ungrounded (hot) circuit conductor, which ensures that the circuit is properly protected by overcurrent devices and that there is no danger of shock or electrocution from the switched conductor.
Learn more about switched conductor here:
https://brainly.com/question/29869573
#SPJ11
State 3 facts about Aluminum:
1. Aluminum is a chemical element. 2. Aluminum is known for its lightweight and 3. Aluminum has a number of important applications in industries.
Here are three facts about Aluminum:
1. Aluminum is a chemical element with the symbol Al and atomic number 13. It is a soft, silvery-white, nonmagnetic metal that is abundant in the earth's crust.
2. Aluminum is known for its lightweight and strong properties, making it a popular material for a variety of products, from transportation to construction. It is also highly resistant to corrosion, making it an ideal material for use in harsh environments.
3. Aluminum has a number of important applications in industries such as aerospace, automotive, and packaging. In the aerospace industry, for example, aluminum is used in the construction of aircraft due to its strength, light weight, and ability to withstand extreme temperatures. In the automotive industry, it is used to make engine blocks, wheels, and body panels. In packaging, it is commonly used to make beverage cans and food containers.
Know more about the Aluminum
https://brainly.com/question/27885413
#SPJ11
What types of memory can be used on a 100-MHz motherboard?
The specific type of memory that can be used on a 100-MHz motherboard depends on the motherboard's memory controller and the type of memory slots that it has.
A motherboard with a 100-MHz front-side bus (FSB) speed typically requires memory that can operate at a speed of 100 MHz or lower.
The most common types of memory that can be used on a 100-MHz motherboard are:
SDRAM (Synchronous Dynamic Random Access Memory):
This type of memory was commonly used in computers with 100-MHz FSB speeds.
SDRAM can operate at speeds of up to 133 MHz and comes in various capacities, ranging from 64 MB to 1 GB.
EDO RAM (Extended Data Out Random Access Memory):
This type of memory was used in some older computers with 100-MHz FSB speeds.
EDO RAM operates at a speed of 66 MHz and comes in capacities ranging from 4 MB to 256 MB.
FPM RAM (Fast Page Mode Random Access Memory):
This type of memory was commonly used in older computers with 100-MHz FSB speeds.
FPM RAM operates at a speed of 66 MHz and comes in capacities ranging from 4 MB to 256 MB.
Buffered and Registered memory:
These are specialized types of memory that are typically used in servers and workstations.
Buffered and Registered memory are designed to improve reliability and stability in high-performance systems, but they may not be compatible with all motherboards.
It is always recommended to check the motherboard's specifications or consult the manufacturer's documentation before purchasing memory for the system.
For similar questions on memory
https://brainly.com/question/31434818
#SPJ11
(370-2) Cablebus is ordinarily assembled at the _____.
(370-2) Cablebus is ordinarily assembled at the manufacturing plant. Manufacturing overhead does not include the depreciation on delivery trucks, but it does include all other possibilities that are still available.
Delivery truck depreciation is not included in the costs associated with making computers. Manufacturing plant overhead, also known as factory burden, factory overhead, or production overhead, is the umbrella term for all costs associated with manufacturing, including electricity costs, costs for factory supplies and indirect labour, rent, insurance, costs for heating, water, and other forms of energy, salaries, and expenses for cleaning, oiling, lubricating, servicing, and repairs.
Manufacturing overhead does not include the depreciation on delivery trucks, but it does include all other possibilities that are still available.
The total of all indirect material, labour, and other costs that are not directly related to the goods and units produced at a manufacturing facility is manufacturing overhead. These are equally distributed to each generated unit.
Learn more about manufacturing plant here
https://brainly.com/question/15071443
#SPJ11
The minimum size of the electrical flexible metal conduit FMC ______ inches electrical trade size.
348.20
According to section 348.20 of the National Electrical Code (NEC), the minimum size of the electrical flexible metal conduit (FMC) is 3/8 inches trade size.
A conduit is a tube or pipe used to protect and route electrical wires and cables in buildings and other structures. It is typically made of metal, plastic, or a combination of both and comes in various sizes and shapes to accommodate different types of wiring systems. Conduit is an essential component of electrical systems as it protects the wires from damage and prevents electrical hazards. It also makes it easier to run and organize wiring, reducing the risk of confusion and errors during installation or maintenance. Proper selection and installation of conduit are critical to ensure the safety and efficiency of electrical systems.
Learn more about conduit here:
https://brainly.com/question/30997640
#SPJ11
Q5)e) What kind of message does the destination host send if it receives a segment that has an error during a TCP connection?
If the destination host receives a segment that has an error during a TCP connection, it will send a message to the source host indicating that the segment has an error. This message is commonly referred to as an "error message" or "error report." The purpose of the error message is to inform the source host that there was an issue with the transmission and to request that the segment be retransmitted.
This process helps ensure reliable and accurate data transmission between the source and destination hosts during a TCP connection.
Learn more about TCP here: brainly.com/question/28119964
#SPJ11
Q9)?c)If someone says that a flag field is set, what does this mean?
A flag field is a field in a data structure that contains one or more binary values that are used to indicate the status of the structure or a specific operation. When someone says that a flag field is set, it means that one or more of the binary values in the field.
They have been turned on or set to a specific value, indicating a particular condition or status. For example, a flag field in a network packet may be set to indicate that the packet is urgent, has errors, or needs to be retransmitted. The specific meaning of a set flag depends on the context in which it is being used. If someone says that a flag field is set, it means that a particular bit or boolean value in a data structure, often used for representing specific conditions or options, has been enabled or marked as true. Flag fields are typically used in programming and digital systems to control or track the state of an operation or event.
Learn more about binary here
https://brainly.in/question/467674
#SPJ11
What is the valid most compressed format possible of the IPv6 address 2001:0DB8:0000:AB00:0000:0000:0000:1234?
The valid most compressed format possible of the IPv6 address 2001:0DB8:0000:AB00:0000:0000:0000:1234 is 2001:DB8:0:AB00::1234.
In IPv6 addresses, groups of consecutive zeros can be compressed to "::", but this can only be done once in an address to avoid ambiguity. In the given address, there are two groups of consecutive zeros, which can be compressed into "::", resulting in the address 2001:DB8:0:AB00::1234. It's worth noting that leading zeros within each group can also be omitted in IPv6 addresses, so "0000" can be expressed as simply "0". However, for clarity and consistency, it's recommended to use the full 4-digit format for each group in most cases.
Learn more about compressed format here:
https://brainly.com/question/11183131
#SPJ11
3) In most audits, the auditor issues a(n)
A) modified opinion audit report.
B) standard unmodified opinion audit report.
C) scope limited audit report.
D) adverse audit report.
The correct answer is (B) In most audits, the auditor issues a B) standard unmodified opinion audit report. This type of report indicates that the auditor believes the financial statements are fairly presented, in all material aspects, in accordance with the applicable financial reporting framework.
A standard unmodified opinion audit report is typically issued by the auditor in most audits.
while rest options are an incorrect modified option, audit report scope limited audit report and adverse audit report is not auditor issues. Thus, the final and correct answer is option b.
Learn more about audit reports here:- brainly.com/question/29354364
#SPJ11
A counter's input signal can come from an external device such as a sensor. true/false
The given statement "A counter's input signal can come from an external device such as a sensor." is true becasue a counter's input signal can come from an external device such as a sensor.
A counter is a device used to count the number of events or objects that have occurred or passed by a specific point. The input signal to the counter can come from various sources, including sensors, switches, and other devices that can detect the occurrence of an event or the presence of an object.
For example, a conveyor belt in a factory can have a sensor that detects the presence of a product, and sends a signal to the counter to increment the count. In this case, the input signal to the counter comes from the sensor that is external to the counter itself.
Therefore, it is true that a counter's input signal can come from an external device such as a sensor.
You can learn more about counter signal at
https://brainly.com/question/29447930
#SPJ11
Question 46
Engineering controls are:
a. controls that isolate or remove hazards from the workplace
b. less effective than good training
c. the last option that should be considered
d. less effective than personal protection processes
Engineering controls are controls that isolate or remove hazards from the workplace. These controls are considered the most effective way to protect workers from occupational hazards because they physically eliminate or reduce the exposure to the hazard. This can be achieved through a variety of means, such as ventilation systems, machine guards, or redesigning work processes.
To summarize, engineering controls are an essential component of workplace safety that isolate or remove hazards from the workplace. They are more effective than relying solely on personal protection and good training, as they directly address the hazard itself.
Learn more about Engineering controls here :brainly.com/question/28221908
#SPJ11
12) The lowest-cost form of transporting goods very long distances by...A) TruckB) TrainC) BoatD) Airplane
The lowest-cost form of transporting goods very long distances by: B: Train
What is the best mode of transportation?There are different modes of transportation such as:
Road Transportation
Maritime Transportation
Air transportation
Rail Transportation
Pipeline transportation
Now, among the listed modes of transportation above, the slowest is usually rail when transporting goods over long distances.
This is because In modern practice, rail is used more exclusively for the largest and heaviest payloads (bulk cargo) traveling across land. The vast majority of railway infrastructure connects highly populated areas with large unpopulated strips of land between them making rail ideal for long-distance and cross country hauls.
Read more about Mode of Transportation at: https://brainly.com/question/25935364
#SPJ1
Algol consists of a 3.7 M Sun main-sequence star and a 0.8 M Sun subgiant. Why does this seem surprising, at least at first?
Choose matching definition
The two stars in a binary system should both be at the same stage of life; that is, they should either both be main sequence stars or both be subgiants.
It doesn't make sense to find a subgiant in a binary star system.
The two stars should be the same age, so we'd expect the subgiant to be more massive than the main-sequence star.
A star with a mass of 3.7 M Sun is too big to be a main-sequence star.
According to Algol's binary system the two stars have different stages of life, with one being a 3.7 M Sun main-sequence star and the other being a 0.8 M Sun subgiant
The surprising aspect of Algol's binary system is that the two stars have different stages of life, with one being a 3.7 M Sun main-sequence star and the other being a 0.8 M Sun subgiant. This is unexpected because the two stars in a binary system are typically expected to be at the same stage of life, either both main sequence stars or both subgiants.
Learn more about Algol's system here
https://brainly.com/question/28149439
#SPJ11
Assume there is a class named BlackBox. Write the header for a member function that converts a BlackBox object to an int.
Assume there is a class named BlackBox. int convertToInt() const; is the header for a member function that converts a BlackBox object to an int.
This header defines a member function called convertToInt in the class BlackBox that returns an integer. The function takes no arguments and is marked as const, indicating that it does not modify the state of the BlackBox object it is called on. The implementation of the function would likely involve extracting some relevant data from the BlackBox object and converting it to an integer. By defining this member function, clients of the BlackBox class can convert objects of this class to integers in a consistent and reliable way.
learn more about function here:
https://brainly.com/question/31473849
#SPJ11
In Class I - Division 1 locations, the entry shall be metric designator trade size ___________ or larger and the enclosure contains terminals splices, ot taps.
501.15
In Class I - Division 1 locations, the entry shall be metric designator trade size 21.0 or larger and the enclosure contains terminals splices, or taps. This requirement is outlined in section 501.15 of the National Electrical Code (NEC).
For such more question on hazardous
https://brainly.com/question/29232461
#SPJ11
a wireless engineer is interested in using an antenna that is commonly used in
A wireless engineer may be interested in using a dipole antenna, which is commonly used in various wireless communication applications. The dipole antenna is easy to construct and can be used for both transmitting and receiving signals. It is a popular choice for applications such as Wi-Fi, Bluetooth, and radio communication.
Identify the requirements: The wireless engineer needs to determine the frequency range, gain, radiation pattern, and polarization required for the specific application. Research common antenna types: Some commonly used antennas include dipole, monopole, Yagi-Uda, and patch antennas. Each type has its advantages and limitations based on the desired application.
Select the appropriate antenna: After comparing the different antenna types, the wireless engineer will choose the one that best fits the requirements and constraints of the project. Design and implementation: The engineer will design the chosen antenna according to the desired specifications, taking into account factors such as size, material, and mounting options. Test and optimize.
In summary, a wireless engineer commonly selects and implements an antenna by identifying the requirements, researching common antenna types, selecting the most suitable option, designing and implementing the antenna, and testing and optimizing its performance.
To know more about wireless engineering:- https://brainly.com/question/28141205
#SPJ11
A wireless engineer may be interested in using a commonly used antenna such as a dipole antenna or a patch antenna.
These types of antennas are popularly used in wireless communication systems due to their ability to provide a directional or omnidirectional signal pattern, depending on the design. Additionally, they are relatively easy to construct and tune for specific frequencies, making them a cost-effective solution for many applications.
Learn more about used antenna: https://brainly.com/question/29846891
#SPJ11
(250-70) The connection of the grounding electrode conductor to a buried grounding electrode (driven ground rod) shall be made with a listed terminal device that is _____.
The connection of the grounding electrode conductor to a buried grounding electrode (driven ground rod) shall be made with a listed terminal device that is suitable for direct burial and corrosion resistant to ensure a secure and reliable connection.
A grounding electrode conductor (GEC) is a component of an electrical system used to provide a low-impedance path for fault currents to travel to the ground. The GEC connects the grounding electrode system, which consists of a set of grounding electrodes, to the equipment grounding conductor of an electrical system.
The purpose of the grounding electrode system is to provide a path for fault currents to flow in the event of an electrical fault, such as a short circuit. By providing a low-impedance path to the ground, the fault current can be safely and quickly directed away from the electrical system, minimizing the risk of electrical shock, equipment damage, and fire.
To learn more about Electrode conductor Here:
https://brainly.com/question/31494083
#SPJ11
5227 - Longitudinal dynamic instability in an airplane can be identified by:- bank oscillations becoming progressively steeper-pitch oscillations becoming progressively steeper-Trilatitudinal roll oscillations becoming progressively steeper
Longitudinal dynamic instability in an airplane can be identified by pitch oscillations becoming progressively steeper.
Longitudinal dynamic instability in an airplane refers to the tendency of the aircraft to oscillate in pitch. This can be identified by observing the pitch oscillations becoming progressively steeper. In addition, bank oscillations may also become progressively steeper as a result of the longitudinal instability. Trilatitudinal roll oscillations may also occur, where the aircraft rolls from side to side while pitching up and down. These oscillations can be dangerous and lead to loss of control of the aircraft, which is why it is important to monitor and address any signs of longitudinal instability during flight..
Longitudinal dynamic instability in an airplane can be identified by pitch oscillations becoming progressively steeper. This means that the airplane's nose will move up and down more severely over time, which can lead to a loss of control if not addressed. This is in contrast to bank oscillations (rolling motion) and trilatitudinal roll oscillations (a term that is not used in aviation).
Learn more about dynamic instability at: brainly.com/question/27960714
#SPJ11
It is okay to download information without asking a lab instructor as long as it is for your online class. true
false
Answer: It is false
Explanation:
Because if you was an kid and you were looking at violent stuff then your parent or guardian catch you looking at it you will be in troble.
What are the benefits of having operator functions that perform object conversion?
Operator functions that perform object conversion, such as type casting or coercion, offer several benefits in programming:
1. Flexibility: They allow you to work with multiple data types, converting between them as needed, to avoid compatibility issues or make your code more versatile.
2. Readability: By explicitly stating the conversion, your code becomes more readable and understandable for others, as the intention behind the conversion is clear.
3. Safety: By using operator functions for conversion, you can handle data type errors or exceptions in a controlled manner, ensuring the stability and reliability of your code.
4. Reusability: Implementing conversion functions within an object or class enables you to reuse the same conversion logic across your codebase, leading to consistent behavior and easier maintenance.
5. Efficiency: By using built-in conversion functions or overloading operators, you can optimize performance by minimizing the overhead of type conversions.
Learn more about Operator functions from : brainly.com/question/27915566
#SPJ11
QUESTION 4
Technician A says that most engine OEMs recommend that customers have the DPF removed and cleaned obce a year to minimize
DPF sintering. Technician B that says that the DPF needs to be actively regenerated at every oil change. Who is correct?
O a. Technician A
b. Technician B
OG Both Technician A and Technician B
O d. Neither Technician A nor Technician B
QUESTION 5
Technician A says that DPFs were used only in HD diesel engines until 2010, when they were replaced with SCR systems.
Technician B says that only a DPF can remove particulate emissions from the exhaust. Who is correct?
O a. Technician A
O b. Technician B
O c. Both Technician A and Technician B
O d. Neither Technician A nor Technician B
Answer to Question 4: Neither Technician A nor Technician B is correct. The Diesel Particulate Filter (DPF) should not be removed and cleaned once a year to minimize DPF sintering. Instead, it should be actively regenerated when it becomes full of soot. There is no need to regenerate the DPF at every oil change.
Answer to Question 5: Technician B is correct. Only a Diesel Particulate Filter (DPF) can remove particulate emissions from the exhaust. However, Technician A is incorrect. DPFs are still used in HD diesel engines, and they were not replaced by Selective Catalytic Reduction (SCR) systems in 2010. Instead, SCR systems are often used in conjunction with DPFs to reduce both particulate matter and NOx emissions.
Every class in Java, except ________, extends an existing class.a. Integer.b. Object.c. String.d. Class.
Every class in Java, except the "Object" class (option b), extends an existing class. The Object class is the base of the Java class hierarchy and does not extend any other class.
The four common types of struck by hazard are: Struck-by Flying objects, Struck-by falling objects, Struck-by swinging objects and Struck-by rolling objects. Struck-by hazard occur when a worker comes into forcible contact with a flying, falling, swinging or rolling object. However, these type of hazard continue to cause many fatalities and serious injuries every year and some even leads to the eventual death of construction workers. A struck by hazard is caused by forcible contact or impact between the injured person and an object or piece of equipment.
Learn more about object here
https://brainly.com/question/14964361
#SPJ11
LP gas is considered more hazardous than natural gas because?
LP gas requires more caution and attention to safety measures when handling, storing, and using it compared to natural gas.
LP (liquefied petroleum) gas is generally considered more hazardous than natural gas for several reasons: Higher flammability: LP gas is more flammable than natural gas because it has a higher energy content per unit of volume. This means that if there is a leak or ignition source, LP gas can ignite more easily and can create a more intense fire or explosion. Heavier than air: LP gas is denser than air, which means it will sink to the ground and collect in low-lying areas if there is a leak. This can create an explosive atmosphere if the gas is not properly ventilated.
Storage under pressure: LP gas is typically stored under pressure in tanks or cylinders, which can pose a risk of rupture or explosion if the tank is damaged or improperly maintained. Odorless: Unlike natural gas, LP gas is odorless in its natural state. An odorant is added to LP gas to give it a distinct smell so that leaks can be detected, but this odorant can sometimes be masked or dissipate over time, making it more difficult to detect leaks.
Learn more about LP gas here:
https://brainly.com/question/15255904
#SPJ11
A device designed to open and close a circuit by non automatic means and to open the circuit automatically on a pre-determined over current without damage to itself when property applied within its rating is defined as a _________.
100
The device described in the question is an electrical switch with an overcurrent protection feature, commonly known as an "overcurrent protective device" or OCPD.
An OCPD is an essential safety device used in electrical systems to protect the wiring and equipment from damage due to excessive current flow. It typically consists of a switch that can be manually operated to open and close a circuit, and a mechanism that detects and responds to overcurrent conditions. When the current flowing through the circuit exceeds a pre-determined level, the overcurrent protection mechanism triggers the switch to open the circuit, thereby interrupting the flow of electricity. This action helps to prevent the electrical equipment from overheating, which can cause fires, explosions, or other hazardous conditions.
Learn more about overcurrent protection here:
https://brainly.com/question/31456221
#SPJ11
The acceleration well fills when the engine is?
The acceleration well is a crucial component in a car's engine system. It is responsible for regulating the flow of fuel to the engine and ensuring that the vehicle accelerates smoothly. The well is typically located in the carburetor and contains a small reservoir of fuel that is used to supplement the fuel flow during acceleration.
So, to answer the question, the acceleration well fills when the engine is running and the accelerator pedal is pressed. When the pedal is depressed, the carburetor's butterfly valve opens wider, allowing more air to flow into the engine, which in turn creates a vacuum that draws fuel from the acceleration well. This additional fuel flow helps to maintain engine performance during acceleration and prevents the car from stalling. Therefore, it is important to ensure that the acceleration well is always properly filled to keep the engine running smoothly.For such more question on carburetor
https://brainly.com/question/25915987
#SPJ11
How many pins are on a DDR DIMM? SDRAM DIMM?
A DDR DIMM (Double Data Rate Dual In-line Memory Module) typically has 184 pins. SDRAM DIMM (Synchronous Dynamic Random Access Memory Dual In-line Memory Module) usually has 168 pins.
DDR DIMM pins are arranged in two rows of 92 pins each, and are used to connect the module to the motherboard. DDR memory is commonly used in desktop computers and some laptops, and is known for its higher speed and lower power consumption compared to older types of memory.
SDRAM DIMM pins are also arranged in two rows, but with 84 pins on each row. SDRAM is an older type of memory that was commonly used in computers before the introduction of DDR memory. SDRAM operates at a lower frequency than DDR memory and is generally slower, but it is still used in some older systems.
In summary, a DDR DIMM typically has 184 pins and is used in newer systems, while an SDRAM DIMM usually has 168 pins and is used in older systems. It is important to check the type of memory required by your system before purchasing a DIMM, as using the wrong type of memory can cause compatibility issues and system instability.
Learn more about computer memory modules : https://brainly.com/question/9720831
#SPJ11
___________ is designed to enable the use of normal Web applications on computers and devices with small display screen operating over low speed wireless connections.
The technology you are referring to is called "Mobile Optimization." Mobile optimization is designed to enable the use of normal Web applications on computers and devices with small display screens, operating over low-speed wireless connections.
The domain at the top of the DNS hierarchy is referred to as a top-level domain, or TLD. This refers to DNS on the Internet. The namespace toot zone has the top-level domain installed as well. The top-level domain, which is generally regarded as the best one, is.com. The second and third are.net and.org. However, as mobile device optimisation is necessary, we should choose.com in this case.
A mobile operating system (OS) is a piece of software Mobile Optimization that enables smartphones, tablet PCs, and other devices to run programmes and apps. When a mobile device is turned on, an operating system normally runs, displaying a screen with icons or tiles that display information.
Learn more about Mobile Optimization here
https://brainly.com/question/30626407
#SPJ11