Longitudinal stability involves the motion of the airplane about its lateral axis, which is controlled by the elevator. Option b is answer.
Longitudinal stability is an important aspect of an airplane's flight characteristics, as it involves the motion of the aircraft about its lateral axis, which affects its pitch or up and down motion. The elevator, which is a control surface on the tail of the airplane, is used to control this motion and maintain longitudinal stability. The angle of attack of the wings also plays a critical role in longitudinal stability.
If the angle of attack is too high, the airplane may stall and lose control, while if it is too low, the airplane may not have enough lift to maintain altitude. In summary, the elevator and angle of attack are the key components involved in maintaining longitudinal stability in an airplane.
Option b is answer.
You can learn more about Longitudinal stability at
https://brainly.com/question/9826817
#SPJ11
Which group of IPv6 addresses cannot be allocated as a host source address?
As the question suggests, the group of IPv6 addresses that cannot be allocated as a host source address are the multicast addresses. Multicast addresses are reserved for communication to multiple hosts simultaneously and cannot be used as a source address for a single host.
The group of IPv6 addresses that cannot be allocated as a host source address is the "Multicast" addresses.
In IPv6, multicast addresses have a prefix of "FF00::/8".
These addresses are used to send packets to multiple hosts simultaneously, rather than a single host, and therefore cannot be used as a source address for a specific host.
Learn more about communication at : brainly.com/question/22558440
#SPJ11
A Boeing 777 landed at Chicago O’Hare Airport (668 m elevation) where the pressure is 98. 8 kPa. Assume that the landing speed is 196. 4 mi/hr. This 777 wing has a coefficient of drag of 0. 034 and its wing area is 429. 1 m2. What is the drag at the point where the aircraft just lands on the ground? Note that these conditions are non-standard so use altitude to calculate temperature then use the pressure given to calculate density
The drag at the point where the aircraft just lands on the ground is approximately 66987 N.
How to calculate the drag force of an aircraftDrag = [tex]\frac{1}{2}*density*velocity^{2} *coefficient of drag*wing area[/tex]
where:
density = atmospheric density at the landing altitude
velocity = landing speed of the aircraft in meters/second
Convert the landing speed from miles per hour to meters per second:
196.4 mi/hr = (196.4*1609.34 m) / (3600 s) = 87.8 m/s
Calculate the atmospheric density at the landing altitude using the following formula:
density = [tex]\frac{pressure}{specific gas constant * temperature}[/tex]
where:
specific gas constant for dry air = 287.058 J/(kg*K)
temperature = standard temperature at sea level - temperature lapse rate * altitude
Assuming a temperature lapse rate of 0.0065 K/m and a standard temperature at sea level of 288.15 K, we can calculate the temperature at the landing altitude as follows:
temperature = 288.15 K - 0.0065 K/m * 668 m = 283.7 K
Substituting these values into the density formula, we get:
density = 98.8 kPa / (287.058 J/(kg*K) * 283.7 K) = 1.036 kg/m³
Finally, we can calculate the drag using the drag formula:
Drag = (1/2) * 1.036 kg/m³ * (87.8 m/s)² * 0.034 * 429.1 m² = 66987 N
Learn more about drag force here:
https://brainly.com/question/27817330
#SPJ4
Based on the assumption that the air resistance is negligible, it is suggested that the overallmotion characteristic of a long jumper may be analyzed by assuming that the center of gravity ofthe athlete undergoes a projectile motion. Consider an athlete who jumps a horizontal distance ofD. The angle of initial jump is 45 degrees. Express the takeoff speed (vo), travel time in the airuntil the jumper hits the ground (t), and maximum vertical height (H), using D and gravitationalacceleration (g). Hint: The travel time reaching to the max vertical height (H) is a half of the total travel time (t)
The travel time reaching the max vertical height (H) is half of the total travel time (t) is given as D/4
What is Maximum Vertical Height?The maximum vertical height is the highest point reached by an object in the air, measured from ground level.
The max height in physics is affected by the object's velocity, launch angle, and air resistance. It's crucial in sports like basketball and high jump where the goal is to reach the highest possible height.
The image provided shows the flight of the athlete and then finds his vertical height.
Read more about vertical height here:
https://brainly.com/question/27101452
#SPJ1
(250-164(A)) DC systems to be grounded and supplied from an off premises source shall have the grounding connection made at _____.
(250-164(A)) DC systems to be grounded and supplied from an off premises source shall have the grounding connection made at the point where the grounded conductor is brought into the building or structure.
This helps to ensure proper grounding of the DC system and prevent electrical hazards.
Hi! According to NEC 250-164(A), DC systems to be grounded and supplied from an off-premises source shall have the grounding connection made at the supply source.
In electrical engineering, the National Electrical Code (NEC) is a set of standards for the safe installation of electrical wiring and equipment. The NEC Article 250-164(A) specifies the requirements for grounding DC systems supplied from an off-premises source.
According to NEC Article 250-164(A), the grounding connection for DC systems to be grounded and supplied from an off-premises source should be made at the source end of the grounded conductor. This means that the grounding connection should be made at the point where the negative or grounded conductor of the DC system is connected to the off-premises power source.
It's important to follow NEC guidelines to ensure the safe and proper installation of electrical systems.
Learn more about grounded and supplied here;
https://brainly.com/question/29526459
#SPJ11
dry foam extraction cleaning is ideal for deeply imbedded carpet soil. group of answer choices true false
The statement "dry foam extraction cleaning is ideal for deeply imbedded carpet soil" is false.
Dry foam extraction cleaning is a low-moisture method of carpet cleaning where a machine is used to generate foam from a carpet cleaning solution. The foam is then spread over the carpet and worked into the fibers with a brush. The foam is then allowed to dry, and the dried foam and soil particles are then vacuumed away.
While dry foam extraction cleaning can be effective for removing surface soil and stains, it may not be the best method for deeply embedded soil. This is because the foam is not able to penetrate as deeply into the carpet fibers as other cleaning methods, such as hot water extraction. Hot water extraction uses high-pressure water and cleaning solution to penetrate deep into the carpet fibers and remove soil and other contaminants.
To know more about dry foam extraction,
https://brainly.com/question/30902399
#SPJ11
How many pins are on a DDR3 DIMM? DDR2 DIMM?
A DDR3 DIMM has 240 pins, while a DDR2 DIMM also has 240 pins. Although both have the same number of pins, they are not interchangeable due to differences in their notch positions and voltage requirements.
A DDR3 DIMM (Double Data Rate 3 Dual Inline Memory Module) has 240 pins, while a DDR2 DIMM (Double Data Rate 2 Dual Inline Memory Module) has 240 pins as well. The number of pins on a DIMM (Dual Inline Memory Module) is an important specification that determines its compatibility with the motherboard. The pins on a DIMM are used to connect the module to the memory controller on the motherboard, which enables the transfer of data between the processor and the memory. DDR2 and DDR3 are different generations of DDR SDRAM (Double Data Rate Synchronous Dynamic Random Access Memory), which have different operating frequencies and timings. However, they have the same number of pins, which allows for backward compatibility, meaning that a DDR3 DIMM can be installed in a motherboard that supports DDR2 memory, but not the other way around.
Learn more about voltage here-
https://brainly.com/question/29445057
#SPJ11
nuclear power plants on earth create energy in the same way as the sun.true or false
False.
Nuclear power plants on Earth create energy through nuclear fission, where heavy atoms like uranium are split, releasing energy.
The Sun, on the other hand, generates energy through nuclear fusion, where lighter atoms like hydrogen combine to form helium, releasing energy in the process.
Learn more about nuclear energy: https://brainly.com/question/11963586
#SPJ11
False. While nuclear power plants and the sun both involve nuclear reactions to create energy, they operate through different processes.
Nuclear power plants use fission, where atoms are split to release energy, while the sun uses fusion, where atoms are combined to release energy.
Energy is the ability of a system to perform work or to produce a change in its environment. It can take many forms, such as kinetic energy, thermal energy, electrical energy, and potential energy. Energy is essential for sustaining life on Earth, as it powers everything from the movement of cars and planes to the growth of plants and animals.
There are many sources of energy, both renewable and non-renewable, such as fossil fuels, nuclear power, wind power, and solar power. As concerns around climate change and environmental sustainability continue to grow, there is an increasing focus on finding cleaner and more sustainable sources of energy.
Efficient energy use and conservation are also important considerations, as they can help reduce energy consumption and minimize environmental impacts. With the rapid pace of technological advancement, the future of energy is likely to be shaped by new innovations and discoveries in the field.
Learn more about Energy here:
https://brainly.com/question/22413310
#SPJ11
T/F: "Contained in" applies when a properly marked source document contains classified information that has been extracted word-for-work and placed into the new document.
The given statement " Contained in applies when a properly marked source document contains classified information that has been extracted word-for-word and placed into the new document." is true because this means that the new document should also be marked with the appropriate classification markings to indicate the level of sensitivity of the information contained within it.
In this context, the "Contained in" marking indicates that the classified information in the new document originated from the source document, and that the source document is the controlling classification authority for that information. The new document may contain additional information that is not classified or may have a different overall classification level than the source document.
Learn more about classified information: https://brainly.com/question/30625702
#SPJ11
A shoulder less than 5 ft with FC-5 can not have what?
A shoulder less than 5 ft with FC-5 pavement cannot have rumble strips.
According to the AASHTO (American Association of State Highway and Transportation Officials) Green Book, for a roadway with FC-5 pavement and a shoulder less than 5 ft wide, rumble strips are not recommended. Rumble strips are used to alert drivers when they are veering off the road or approaching a hazardous area. However, on narrow shoulders, rumble strips can be a hazard themselves, causing drivers to swerve or lose control. Therefore, for safety reasons, rumble strips are not recommended on narrow shoulders with FC-5 pavement.
Learn more about AASHTO here:
https://brainly.com/question/29080719
#SPJ11
During installation, one may decide to go with the default drivers because they _______________.A.will always workB.can be upgraded laterC.must be used initiallyD.are available at no cost
The main reason to use default drivers during installation is their compatibility and reliability, but they may not always provide the optimal performance or features of the device.
During installation, one may decide to go with the default drivers because they are expected to work with the device being installed. The default drivers are usually pre-installed with the operating system or provided by the manufacturer of the device. They are designed to provide basic functionality to the device, such as allowing it to communicate with the computer or other connected devices. While default drivers may not always provide all the features or capabilities of the device, they are usually stable and reliable, and can be used until better drivers are available or until the user decides to upgrade them. Default drivers can also be updated later if needed, either through the operating system's automatic updates or by manually downloading and installing updated drivers from the manufacturer's website.
Learn more about drivers here:
https://brainly.com/question/29992205
#SPJ11
Frames of switchgear and control assemblies shall be _____________.
490.36
Frames of switchgear and control assemblies shall be suitable for the content loaded within them. According to NEC 490.36, the frames must be able to withstand the weight and distribution of the equipment and components installed within the assemblies.
Properly designed and constructed frames are essential for the safe and reliable operation of switchgear and control assemblies. The frames must be able to protect the equipment from damage, provide adequate support, and allow for proper ventilation. As such, manufacturers of switchgear and control assemblies should pay close attention to the design and construction of the frames to ensure compliance with NEC 490.36 and the safety of the equipment. Frames of switchgear and control assemblies shall be content loaded.
Learn more about switchgear here: brainly.com/question/30745390
#SPJ11
This entity is responsible for ensuring the proper and legal incorporation of security considerations:
a. Anti-Terrorism Working Group (ATWG)
b. Anti-Terrorism Officer
c. CI Support Personnel
d. Force Protection Working Group (FPWG)
e. Information Systems Security Managers (ISSM)
f. Installation Commander/Facility Director
g. Law Enforcement Officials
h. Legal Officers
i. Operations Security Officer
j. Physical Security Officer/Provost Marshal
k. Threat Working Group (TWG)
The Physical Security Officer/Provost Marshal is the entity responsible for ensuring the proper identifier and legal incorporation of security considerations.
The entity responsible for ensuring the proper identifier and legal incorporation of security considerations is the Security Enforcement entity, which may include Law Enforcement Officials, the Physical Security Officer/Provost Marshal, the Installation Commander/Facility Director, or the Operations Security Officer. Legal Officers may also provide guidance on the legal aspects of security enforcement. They work closely with law enforcement, operations, and other security-related personnel to maintain the safety and integrity of facilities and installations.
Their responsibilities include the installation, use, and maintenance of security equipment, from metal detectors to electronic monitoring. They may also interact with guests and staff for security reasons. Responsibilities include accessing guest and electronic information and overseeing all security.
Learn more about Identifier:
https://brainly.com/question/31494133
#SPJ11
Assume you have a clock running at 2GHz. Design the following:
(a) A clock divider pulsing every 38 nanoseconds using an 8 bit up-counter and additional logic. (b) A clock divider pulsing every 540 microseconds using a 24-bit down-counter with a load input. (c) A clock divider pulsing every 1 millisecond using a 32-bit up-counter with a load input and no additional logic.
Some examples include a clock divider using an 8-bit up-counter with additional logic pulsing every 38 nanoseconds, a clock divider using a 24-bit down-counter with load input pulsing every 540 microseconds.
What are some examples of clock dividers with different configurations?The given paragraph describes three clock divider circuits used to generate clock signals with different frequencies. A clock divider is a digital circuit that reduces the frequency of an input clock signal to a lower frequency output clock signal.
The first circuit uses an 8-bit up-counter and additional logic to divide the clock pulse every 38 nanoseconds. The up-counter counts up from 0 to 255 and then resets to 0, generating an output pulse for every 256 input pulses. The additional logic is used to adjust the output frequency to the desired frequency of 1 pulse every 38 nanoseconds.
The second circuit uses a 24-bit down-counter with a load input to divide the clock pulse every 540 microseconds. The down-counter counts down from a preset value of 2^24-1 to 0, generating an output pulse when the counter reaches 0. The load input is used to preset the counter with the desired value to achieve the output frequency of 1 pulse every 540 microseconds.
The third circuit uses a 32-bit up-counter with a load input and no additional logic to divide the clock pulse every 1 millisecond. The up-counter counts up from 0 to 2^32-1 and then resets to 0, generating an output pulse for every 2^32 input pulses. The load input is used to preset the counter with the desired value to achieve the output frequency of 1 pulse every 1 millisecond.
Learn more about clock
brainly.com/question/30436581
#SPJ11
A timer delay time equals the value in the ACC multiplied by the time base. true/false
The given statement "A timer delay time equals the value in the ACC multiplied by the time base " is true.
In many electronic systems, timer circuits are used to generate accurate delays. These circuits consist of a counter and a clock source, and the delay time is determined by the count value of the counter and the frequency of the clock. In some cases, the delay time is set by an external signal, while in others, it is determined by the value of a register in the system.
In the case of a timer delay time equaling the value in the ACC (accumulator) multiplied by the time base, this means that the delay time is directly proportional to the value stored in the ACC and the time base. The ACC is a register in the system that stores data temporarily for processing, and the time base is the frequency of the clock used by the timer circuit.
Thus, if the value of the ACC is increased, the delay time will also increase proportionally. Similarly, if the time base frequency is increased, the delay time will decrease proportionally. This relationship is essential in designing and programming accurate timing circuits in electronic systems.
You can learn more about electronic systems at: brainly.com/question/28166552
#SPJ11
How many 30-pin SIMMs are installed in one bank?
The number of 30-pin SIMMs installed in one bank can vary from 2 to 8, depending on the size of the individual SIMMs and the configuration of the memory bank.
72-pin SIMMs, the number of 30-pin SIMMs installed in one bank depends on the type of SIMM and the memory controller of the computer.
30-pin SIMMs were used in older computers, such as the first generations of Macintosh computers and some IBM PCs.
SIMMs typically came in sizes of 256KB, 512KB, 1MB, 2MB, 4MB, and 8MB.
A bank of memory using 256KB or 512KB SIMMs would typically have 8 slots, whereas banks of 1MB and 2MB SIMMs would have 4 slots.
Banks using 4MB and 8MB SIMMs would have 2 slots.
It is worth noting that 30-pin SIMMs are no longer commonly used in modern computers.
For similar questions on bank
https://brainly.com/question/14905714
#SPJ11
The collections framework algorithms are ___, i.e., each of these algorithms can operate on objects that offer given interfaces without concern to the underlying implementations
The collections framework algorithms are implementation-agnostic, i.e., each of these algorithms can operate on objects that offer given interfaces without concern to the underlying implementations.
This allows for flexibility and adaptability when working with different types of collections. The collections framework algorithms are interface-based, i.e., each of these algorithms can operate on objects that offer given interfaces without concern to the underlying implementations. This means that the algorithms are designed to work with any class that implements the required interface, regardless of how the class is implemented internally. This allows for greater flexibility and reusability of code within the collections framework.
Learn More about framework here :-
https://brainly.com/question/28991812
#SPJ11
The purpose of an anti-afterfire solenoid is to?
The purpose of an anti-afterfire solenoid is to prevent afterfire in an engine by controlling the flow of fuel to the carburetor during shutdown.
The purpose of an anti-afterfire solenoid is to prevent the engine from backfiring or producing afterfire by shutting off the fuel supply to the carburetor after the ignition is turned off.
This ensures a proper fuel-to-air mixture, reducing the chances of any unburned fuel igniting in the exhaust system and causing afterfire.This solenoid allows the remaining fuel in the carburetor to burn out before the engine shuts down completely, preventing afterfire and potential damage to the engine. It can also be explained that afterfire occurs when unburned fuel vapors ignite in the exhaust system, producing a loud popping or banging noise. This can occur due to a variety of reasons such as a rich fuel mixture, faulty ignition timing, or worn out spark plugs.However, by installing an anti-afterfire solenoid, the fuel supply is cut off and any remaining fuel in the carburetor is burned out, preventing afterfire and protecting the engine.
Know more about the solenoid
https://brainly.com/question/29916041
#SPJ11
Paul Rand realized that to be functional over a long period of time, thus Rand sought to create trademark designs based on elementary shapes that were:
The question is about the principles that Paul Rand followed when creating trademark designs to ensure their functionality over a long period of time. Paul Rand realized that to achieve this, he needed to create trademark designs based on elementary shapes that were simple, timeless, and easily recognizable.
Paul Rand believed that in order for trademark designs to remain functional and effective over a long period of time, they needed to be simple and timeless. By focusing on these characteristics, Rand was able to design logos that remained functional and relevant for many years.
He sought to create designs based on elementary shapes such as circles, squares, and triangles, which could be easily recognized and understood by a wide audience. By using these basic shapes, Rand was able to create logos and trademarks that were not only visually appealing, but also highly memorable and easily adaptable to different contexts and applications.In essence, Rand's approach to design was grounded in a deep understanding of the principles of simplicity, clarity, and longevity, which enabled him to create iconic brand identities that have stood the test of time.
Know more about the trademark
https://brainly.com/question/11957410
#SPJ11
Question 13
A major worry associated with prolonged, low-level PCB exposure is:
a. general tiredness
b. loss of appetite
c. liver cancer
d. reproductive problems
The major worry associated with prolonged, low-level PCB exposure is reproductive problems. However, PCB exposure can also lead to other health concerns such as liver cancer, general tiredness, and loss of appetite.
A major worry associated with prolonged, low-level PCB exposure is:d. reproductive problems
PCBs are known to be persistent organic pollutants (POPs) that can accumulate in the environment and in the food chain, leading to potential exposure through the consumption of contaminated fish, meat, and dairy products. Even at low levels, long-term exposure to PCBs has been associated with a range of health problems, including developmental and cognitive impairments, endocrine disruption, immune system dysfunction, and an increased risk of cancer. Because of these concerns, the production and use of PCBs have been banned in many countries, but PCBs can still be found in some products, and they continue to be a public health concern.
Learn more about prolonged here
https://brainly.in/question/12965989
#SPJ11
Duringan annual cleaning of an outdoor condensing unit, bent fins should be _______________.
During an annual cleaning of an outdoor condensing unit,, bent fins should be straightened out to ensure proper airflow and maximum efficiency.
The condensing unit is an essential part of any air conditioning or refrigeration system, and it works by transferring heat from the indoor air to the outside environment. The fins in the unit play a crucial role in this process by helping to dissipate the heat absorbed by the refrigerant.
Over time, the fins may become bent or damaged due to various reasons such as weather conditions, debris accumulation, or accidental damage.
When fins are bent, the airflow through the condenser coil can be restricted, causing the unit to work harder and less efficiently, leading to higher energy costs and potential damage to the system.
Straightening the bent fins during the annual cleaning process is a relatively simple and inexpensive maintenance task that can have a significant impact on the performance of the system.
It involves using a fin comb or a similar tool to gently straighten the fins back to their original position. This process allows air to flow more freely through the coil, reducing the workload of the compressor and improving the overall efficiency of the system.
In conclusion, during an annual cleaning of an outdoor condensing unit, straightening the bent fins is an essential task that should not be overlooked.
It is a simple and cost-effective way to maintain the efficiency of the system and ensure its longevity, ultimately saving you time and money in the long run.
For more question on "Outdoor Condensing Unit" :
https://brainly.com/question/26261685
#SPJ11
The _________operates like the IETF through small research groups focused on specific issues.
a. Internet Society
b. University Corporation for Advanced Internet Development
c. Internet Engineering Steering Committee
d. Internet Architecture Board
e. Internet Research Task Force
e. Internet Research Task Force
The Internet Research Task Force (IRTF) operates like the IETF through small research groups focused on specific issues.
The length of the suitable coat and cable assemblies approved for extra hard usage for branches from bus-ways for the connection of equipment shall not exceed ________ feet.
368.17(b)(7)
The length of the suitable coat and cable assembly approved for extra hard usage for branches from busways for the connection of equipment shall not exceed 6 feet. This is according to NEC section 368.17(b)(7).
Based on the National Electrical Code (NEC) section 368.17(B)(7), the length of the suitable coat and cable assemblies approved for extra hard usage for branches from busways for the connection of equipment shall not exceed 6 feet.
A wiring is a group of wires arranged in a unit for a specific purpose. Cable assemblies are also called wiring harnesses or plumbing. These cables are bundled together in length and direction to make installation easier and faster. A cable assembly is a group of wires or cables connected to a unit. The purpose of this product is to provide power from many different cables while arranging them in a package that is easy to install, replace and manage.
Learn more about cable assembly:
brainly.com/question/30831285
#SPJ11
In a room containing a 480 volt switchboard, a mosonary wall oposite the front of the switchboard is considered to be ____________.
110.26(a)(6)
The main answer is "an unacceptable location." According to electrical safety standards, a masonry wall opposite the front of a 480 volt switchboard is considered to be an unacceptable location.
because it can obstruct access to the switchboard and prevent safe operation and maintenance. The National Electrical Code (NEC) requires a minimum working space in front of electrical equipment, and this space must be kept clear and unobstructed. A masonry wall can also create a hazard by reflecting electrical arcs and increasing the risk of electric shock and fire. Therefore, it is important to ensure that the area in front of switchboards and other electrical equipment is free from obstructions and complies with safety regulations.
Learn more about electrical equipment here:
https://brainly.com/question/31256244
#SPJ11
X-ray installed long time rating based on an operating interval of _________ minute or longer.
517.2
An X-ray machine is installed with a long-time rating based on an operating interval of 517.2 minutes or longer. This means that the X-ray equipment is designed to operate safely and effectively for periods of 517.2 minutes (about 8.6 hours) or longer without experiencing issues related to its performance or safety.
X-rays, or less commonly X-rays, are high-energy electromagnetic radiations. Most X-rays have wavelengths in the 10 picometers to 10-nanometer range and energies in the 145 eV to 145 range, corresponding to frequencies in the 30 petahertz to 30 Ahtz (3 × 1016 Hz to 3 × 1019 Hz) range. house. Kev. X-rays have shorter wavelengths than ultraviolet rays and generally longer wavelengths than gamma rays. X-rays are called X-ray radiation in many languages and are named after German scientist Wilhelm Conrad Röntgen, who discovered it on November 8, 1895. Send out an unknown type of radiation is called an X-ray. The English X-ray notation includes the lines x-ray(s), xray(s), and X-ray(s).
X-rays are also used to detect broken bones, diagnose certain diseases, "show certain metals" and find weak spots in metals, etc. using for. An X-ray machine is installed with a long-time rating based on an operating interval of 517.2 minutes or longer. This means that the X-ray equipment is designed to operate safely and effectively for periods of 517.2 minutes (about 8.6 hours) or longer without experiencing issues related to its performance or safety.
Learn more about installed:
brainly.com/question/13267432
#SPJ11
How do you calculate the tolerance for the asphalt spread rate target?
The tolerance for the asphalt spread rate target can be calculated using the following formula.
Tolerance = (Target Spread Rate x Tolerance Percentage)/100 Target Spread Rate is the desired spread rate for the asphalt
Tolerance Percentage is the allowable deviation from the target spread rate, expressed as a percentage
For example, if the target spread rate is 2.5 inches per square yard and the allowable deviation is ±5%, the tolerance for the spread rate would be: Tolerance = (2.5 x 5)/100
Tolerance = 0.125 inches per square yard Therefore, the acceptable range for the spread rate would be between 2.375 inches per square yard (2.5 - 0.125) and 2.625 inches per square yard (2.5 + 0.125).
Learn more about asphalt spread here:
https://brainly.com/question/29589497
#SPJ11
Question 12
The most characteristic symptom of individuals occupationally exposed to PCBs is:
a. chloracne
b. live cancer
c. visual disturbance
d. physical tremor
The most characteristic symptom of individuals occupationally exposed to PCBs is:
a. chloracne
Chloracne is a type of acne-like skin rash that is caused by exposure to certain chemicals, including PCBs. It is a persistent and disfiguring condition that can develop within weeks to months of exposure. Chloracne typically appears on the face, neck, and upper trunk and is characterized by the presence of blackheads, cysts, and pustules.
Learn more about humans here
https://brainly.in/question/9973537
#SPJ11
The counter accumulated value is the current count based on the number of times the ring goes from false to true. true/false
The given statement "The counter accumulated value is the current count based on the number of times the ring goes from false to true." is false because the counter accumulated value is the current count based on the number of times the input signal goes from false to true.
The counter counts these rising edges and increments its accumulated value accordingly. For example, a counter with an accumulated value of 10 has counted 10 rising edges of the input signal. The counter can be reset to 0 using a reset signal, and can be preset to a specific value using a preset signal.
You can learn more about counter accumulated value at
https://brainly.com/question/30328887
#SPJ11
Q6) e) Ethernet does error detection but not error correction. Is Ethernet a reliable protocol? Explain.
Ethernet is a widely used networking protocol that provides reliable data transmission. Although Ethernet does error detection, it does not offer error correction. This means that when errors are detected in data packets, Ethernet discards them rather than attempting to correct them. This may raise concerns about the reliability of the Ethernet protocol.
For such more question on protocol
https://brainly.com/question/28811877
#SPJ11
In older cities across South Africa, infrastructure is deteriorating, including water lines that supply homes and businesses. A report to the Gqeberha municipal council stated that there are on average 30 water line breaks per 100km’s a year in the city. Outside Gqeberha, the number of breaks is 15/km a year
Where the above conditions are given:
A) we can calculate this probability to be approximately 0.1665 or 16.65%.
B) we can calculate this probability to be approximately 0.1612 or 16.12%.
a) Let X be the number of water line breaks in a stretch of 100kks in Gqeberha in a year. We know that X follows a Poisson distribution with λ = 30. To find the probability of 35 or more breaks, we can use the Poisson distribution formula:
P(X ≥ 35) = 1 - P(X < 35) = 1 - Σi=0^34 e^(-30) * 30^i / i!
Using a calculator or software, we can calculate this probability to be approximately 0.1665 or 16.65%.
b) Let Y be the number of water line breaks in a stretch of 100kks outside of Gqeberha in a year. We know that Y follows a Poisson distribution with λ = 15. To find the probability of 12 or fewer breaks, we can again use the Poisson distribution formula:
P(Y ≤ 12) = Σi=0^12 e^(-15) * 15^i / i!
Using a calculator or software, we can calculate this probability to be approximately 0.1612 or 16.12%.
Learn more about probability at:
https://brainly.com/question/30034780
#SPJ1
Full Question:
Although part of your question is missing, you might be referring to this full question:
In Older Cities Across South Africa, Infrastructure Is Deteriorating, Including Water Lines That Supply Homes And Businesses. A Report To The Gqeberha Municipal Council Stated That There Are On Average 30 Water Line Breaks Per 100 ’ A Year In The City. Outside Gqeberha, The Number Of Breaks Is 15/ A Year. A) Find The Probability That In A
In older cities across South Africa, infrastructure is deteriorating, including water lines that supply homes and businesses. A report to the Gqeberha municipal council stated that there are on average 30 water line breaks per 100 ’ a year in the city. Outside Gqeberha, the number of breaks is 15/ a year.
a) Find the probability that in a stretch 100 ’ in Gqeberha there will be 35 or more breaks next year. (3)
b) Find the probability that there will be 12 or fewer breaks in a stretch of 100 ′ outside of Gqeberha next year.
The overhead service conductors from the last pole or other aerial support to and including the splices, if any, connection to the service-entrance conductors at the building or other structure.
10 def.
The overhead service conductors refer to the wires that are responsible for carrying electrical power from the last pole or aerial support to the building or other structure. These conductors include all the components, including any splices that are used to connect the service-entrance conductors at the building or other structure.
Overall, the structure of these service conductors is an essential aspect of ensuring that electrical service is safely and reliably delivered to homes and businesses.
Overhead support The conductors are those that run from the service point to the building's or other structure's first point of connection to the service-entrance conductors.
A substance or material that allows the passage of power is known as an electric conductor. When voltage is applied, electric charge carriers—typically electrons or ions—move without difficulty from one atom to the next in a conductor.
Conductors are the substances or materials that let energy pass through them. Additionally, conductors allow heat to pass through them. Metals, the human body, the Earth, and animals are some examples of conductors. The body is a powerful conductor.
Learn more about service conductors here
https://brainly.com/question/28298618
#SPJ11