(334-80) The ampacity of nonmetallic sheath cable shall be hat of 60 C as listed in Table 310-15(A)(16). However the 90 C ampacity listed in Table 310-15(A)(16) can be used for ampacity adjustment purposes, provided the final adjusted ampacity does not exceed that of a _____ rated conductor.

We should position the metre scale along the item such that the zero mark of the metre scale aligns with one end of the object if we want to measure an object's length using metres. The length of the object will then be revealed by the reading on the scale's opposite end.

A foot or so distant or close enough to read a ruler, stand in front of a mirror. The 0 on a plastic ruler should be positioned in the centre of your pupil when you hold it vertically against the frame. The bottom edge of the lens, not the frame's edge, should be measured from the middle of your pupil. Keep track of each eye's height.

Learn more about eye's height

https://brainly.com/question/10255119

#SPJ1

The correct answer is (b) a short bar magnet because the circular loop of current creates a magnetic field that looks similar to the field created by a bar magnet.

The magnetic field around a current-carrying, circular loop is similar to that of a bar magnet because the circular loop acts as a magnetic dipole, with a north and south pole, just like a bar magnet. The magnetic field lines around the circular loop are also circular, just like the field lines around a bar magnet.

    The other options, such as a current-carrying, rectangular loop or long straight wire, do not produce a magnetic field that is similar to a bar magnet. Additionally, the strength of the magnetic field is greatest at the center of the circular loop and decreases with distance. This is similar to the field of a bar magnet, where the field is strongest at the poles and diminishes with distance.

To learn more about magnetic field click here https://brainly.com/question/23096032

#SPJ11

Yes, the Magnus effect can explain why a pitch baseball curves and a golf ball slices. The Magnus effect refers to the force created by the rotation of a spinning object, such as a baseball or a golf ball, which causes a pressure differential around the object.

This pressure differential then creates a force that can cause the object to curve or slice in a particular direction. In the case of a pitch baseball, the spin of the ball creates a pressure differential that causes it to curve, while in the case of a golf ball, the spin causes it to slice. So, the Magnus effect plays a key role in explaining the movement of both baseballs and golf ballsThe Magnus effect is a particular manifestation of Bernoulli's theorem: fluid pressure decreases at points where the speed of the fluid increases. In the case of a ball spinning through the air, the turning ball drags some of the air around with it

To know more about  Bernoulli's theorem please vist :-

https://brainly.com/question/29159533

#SPJ11

The reaction constant or variable (1). Variable, because the slope changes as a function of time is the correct option.

Option 1 is the best choice given the available data, as the reaction's rate is varied as a result of the slope changing with time. When discussing a chemical reaction's rate, it is important to note that as the concentrations of reactants and products change over time, the rate can also fluctuate. The rate of a reaction is frequently calculated from the slope of a plot of reactant or product concentration vs time. However, this slope might change during the course of a reaction, indicating that the rate is variable rather than constant.

Therefore, the correct option is (1).

To know more about slope

https://brainly.com/question/29254127

#SPJ4

The angular speed of the wheels is 20 rad/s. When  a bicycle with wheels of radius 0.4 m travels on a level road at a speed of 8 m/s.

The linear speed of a point on the edge of a wheel is equal to the product of the angular speed and the radius of the wheel. Therefore, we can use the formula:
linear speed = angular speed x radius
To find the angular speed, we can rearrange this formula as:
angular speed = linear speed / radius
Plugging in the given values, we get:
angular speed = 8 m/s / 0.4 m = 20 rad/s
Therefore, the angular speed of the wheels is 20 rad/s, the answer is (B) 20 rad/s.

learn more about angular speed Refer: https://brainly.com/question/9684874

#SPJ11

The two ways that inertia affect the motions of the planets are:

B. It keeps the planets from flying off into space, out of the solar system.

C. It causes the planets to keep moving in the same direction as they did when they formed.

Inertia helps to keep planets in their orbits around the Sun, preventing them from flying off into space. As the planets move around the Sun, they are constantly pulled by the Sun's gravity towards the center of their orbit. However, due to their inertia, they continue to move forward, and the resulting combination of the inward pull of gravity and the outward motion due to inertia causes the planets to move in stable, elliptical orbits.

The planets formed from a cloud of gas and dust that was rotating in a particular direction. Due to the conservation of angular momentum, this rotation was transferred to the planets as they formed, causing them to continue to rotate in the same direction as they did when they formed. This is an example of how inertia affects the motion of the planets.

Learn about motions of planet here https://brainly.com/question/986278

#SPJ1

If one of the wind turbines with different length blades is to spin more quickly, the angular acceleration, a should be positive. This means that the rate of change of the angular velocity should be in the direction of increasing speed.

To change the angular speed of one of the wind turbines with different length blades, you would need to adjust the angular acceleration (a). If the turbine is to spin more quickly, the angular acceleration (a) should be positive. A positive angular acceleration indicates an increase in angular speed, while a negative value would indicate a decrease in angular speed.

The angular acceleration is the time rate of change of the angular velocity and is usually designated by α and expressed in radians per second per second. For the case in which the angular velocity is uniform (nonvarying), θ = ωt and α = 0. If α is uniform but not zero, ω = αt and θ = 1/2αt².

Visit here to learn more about  angular acceleration : https://brainly.com/question/30237820
#SPJ11

Roentgen Equivalent Man. The term rem is a unit of measurement used to quantify the amount of radiation someone is exposed to, taking into account the type of radiation and its potential to cause harm. It is a combination of the Roentgen energy measure and the radiation weighting factor.

The term "rem" is short for: Roentgen equivalent measure Rem stands for Roentgen equivalent measure, which is a unit used to quantify the biological effect of ionizing radiation. It takes into account the type of radiation and its energy, allowing for a comparison of different radiation exposures in terms of their potential harm to living organisms.also known as the equivalent dose.  One of the most important portions of the sleep cycle is called REM sleep. REM stands for Rapid Eye Movement, and it’s both the deepest and most active stage of sleep. REM is essential if you want to reap the full benefits of sleep and feel rested after a night in bed.

learn more about Roentgen here

https://brainly.com/question/31559773

#SPJ11

Based on the given information, an inelastic collision occurred between the 2kg ball traveling to the right at 6m/s and the 1 kg ball at rest.

An inelastic collision is one in which the kinetic energy of the colliding objects is not conserved, and the objects stick together after the collision. In this case, the two balls stuck together after the collision, resulting in the final velocities of the 2kg ball traveling to the right at 2 m/s and the 1 kg ball traveling to the right at 8 m/s.

An inelastic collision, as opposed to an elastic collision, is one in which internal friction prevents the conservation of kinetic energy.

When macroscopic bodies collide, some of the kinetic energy is converted into atomic vibrational energy, which results in heating and deformation of the bodies.

To know more about inelastic collision click here:

https://brainly.com/question/24616147

#SPJ11

Maximum range and maximum distance glide are performance characteristics of flight at maximum lift/drag ratio in a propeller-driven airplane. So, option b is right choice.

When a propeller-driven airplane is flying at maximum lift/drag ratio, it means that it is flying at its most efficient speed, where the lift generated by the wings is equal to the drag created by the airplane's motion through the air. This results in a number of performance characteristics that are beneficial for the aircraft.
One of the key characteristics of flight at maximum lift/drag ratio is the ability to gain altitude over a given distance. Since the airplane is operating at its most efficient speed, it is able to climb more easily and quickly than it would at other speeds.

This can be particularly important in situations where the airplane needs to gain altitude rapidly, such as during takeoff or when flying through turbulent air.
Another important characteristic of flight at maximum lift/drag ratio is the ability to achieve maximum range and maximum distance glide.

Since the airplane is operating at its most efficient speed, it is able to cover the greatest distance for a given amount of fuel, making it ideal for long-distance flights.

Additionally, if the airplane were to experience an engine failure, it would be able to glide for the greatest distance before needing to land.
Finally, flight at maximum lift/drag ratio is characterized by a high coefficient of lift and a low coefficient of drag. This means that the airplane is able to generate a greater amount of lift while producing less drag, which helps to maximize its efficiency.

The high lift coefficient also allows the airplane to fly at slower speeds, making it more maneuverable and easier to control.

So, option b is right.

For similar question on lift/drag ratio

https://brainly.com/question/30025752

#SPJ11

Question:-

What performance is a characteristic of flight at maximum lift/drag ratio in a propeller-driven airplane?

a.- gain in altitude over a given distance- range and maximum distance glide

b. - coefficient of lift and minimum coefficient of drag  200 words

In small communities and rural places, a slow sand filter is recommended for use.

This type of filter is effective, low-cost, and easy to maintain, making it suitable for these settings. For small communities and rural places, slow sand filters are often recommended as they are low cost, low maintenance, and effective in removing a wide range of contaminants. Slow sand filters use a combination of biological and physical processes to remove particles and pathogens from water. They work by passing water slowly through a bed of fine sand, which acts as a physical filter, and a layer of microorganisms, which help to break down and remove organic matter and pathogens. Slow sand filters have been used for centuries and are still widely used today in many parts of the world.

To learn more about slow sand filter, refer:-

https://brainly.com/question/13042158

#SPJ11

option (b). The packing gland serves many functions in a centrifugal pump. Among these, it keeps gritty material from entering the packing box. The packing gland is an important component of a centrifugal pump that helps to maintain the pump's efficiency and prevent damage to its internal parts.

One of its primary functions is to seal the area where the pump shaft exits the casing, which is known as the packing box. This is important because the pump shaft rotates at high speeds and generates significant friction, which can cause wear and tear on the packing box if it is not properly sealed.

One of the main challenges of operating a centrifugal pump is that it can become clogged with gritty or abrasive materials that can cause damage to the pump's internal components. The packing gland helps to prevent this by creating a tight seal around the pump shaft that keeps these materials from entering the packing box. This not only helps to prevent damage to the pump but also ensures that the pump operates more efficiently and has a longer service life.

Find out more about  packing gland

brainly.com/question/15585444

#SPJ11

Intermodal option combines truck and rail transportation with conventional road trailers carried atop rail flatcars for the long (line-haul) segment of the transit (d). Trailer on Flatcar is correct option.

For the long-distance (line-haul) leg of transit, trailer on flatcar, sometimes referred to as TOFC or piggyback, combines truck and rail transportation. In this manner, pickup and delivery at the origin and destination sites are handled by trucks while standard road trailers, or "pigs," are loaded onto rail flatcars and transported by rail for the long run. This enables the use of trucks' flexibility for the initial and last miles of transit while still utilizing the long-distance efficiency of rail transportation.

To know more about Intermodal

https://brainly.com/question/14310766

#SPJ4

The distance from the central bright fringe to the 3rd dark fringe is approximately 0.48 cm.

Solution

The distance between the central bright fringe and the 3rd dark fringe in a double-slit experiment is given by:

y = (m * λ * L) / d

If y denotes the distance between the edges,

m is the fringe order (an integer value representing the number of bright or dark fringes away from the central fringe),

λ is the wavelength of the light,

L is the length between the two slits.

The distance between the two slits is given by d.

Substituting the given values, we get:

y = (3 * 600 nm * 150 cm) / 3.55 μm

y = 4800 nm

Converting nanometers to centimeters, we get:

y = 4800 nm * (1 cm / 10^7 nm)

y = 0.48 cm

Therefore, the distance from the central bright fringe to the 3rd dark fringe is approximately 0.48 cm.

Learn more about Distance here

brainly.com/question/7243416

b. 1000-5000 cps.

Answer - Hi! Maximum sensitivity to sound for humans is in the range of 1000-5000 cps (cycles per second The cycle per second is a once-common English name for the unit of frequency now known as the hertz. Cycles per second may be denoted by c.p.s., c/s, or, ambiguously, just "cycles"). So, the correct answer is option b. 1000-5000 cps.Sound frequency is measured in terms of cycles per second (cps), or hertz (Hz), which is the standard unit for cps. The normal human ear can detect sounds that range in frequency from about 20 Hz to about 15,000 Hz.

to learn more about human hearing range, click on this -

brainly.com/question/14718543

#SPJ11

The order of increasing force of attraction between submicroscopic particles is (c) air < (b) water < (a) sugar.

This is because sugar molecules have stronger intermolecular forces of attraction than water, and air molecules have weak intermolecular forces of attraction compared to both sugar molecules and water molecules.Force of attraction is a force that pulls the body near due to its attraction. There are numerous attractive forces prevailing in nature. Some of them are magnetic force, electric force, electrostatic force and gravitational force

To know more about force  please click:-
https://brainly.com/question/807785

#SPJ11

When using presettling reservoirs to eliminate heavy turbidity or pollution before treatment, the desirable retention time is typically 2 to 3 days.

This allows sufficient time for the heavy particles to settle to the bottom of the reservoir and the clearer water to move to the treatment process. A retention time of 8 hours or 1 week may not be sufficient for effective settling, while a retention time of 1 month or longer may not be practical due to space and time constraints.

To know more about reservoirs, please click on:

https://brainly.com/question/482974

#SPJ11

Microwaves, which are a type of electromagnetic radiation, are reflected by surfaces that are metallic or have high electrical conductivity, such as metals, aluminum foil, and certain types of plastics. These surfaces can cause the microwaves to bounce back instead of being absorbed, leading to uneven heating and potential damage to the microwave.  

These materials can include aluminum foil, metal mesh, and certain metallic coatings. When microwaves encounter these surfaces, their energy is unable to pass through and is instead reflected back, often causing an even distribution of energy in the microwave oven.

It is important to always use microwave-safe dishes and avoid placing any metal objects inside the microwave.

To know more about Microwaves:

https://brainly.com/question/4537604

#SPJ11

a. The skin is the correct option. Microwave-induced injury is best understood when it involves the skin. Microwaves are a form of electromagnetic radiation that can cause heating effects on living tissues. When the skin is exposed to microwaves, the energy is absorbed, causing an increase in temperature that may lead to tissue damage.

Squamous cell destruction is a term related to the damage or destruction of squamous cells, which are flat, scale-like cells that make up the outer layer of the skin called the epidermis. While microwaves can cause damage to these cells, the broader category of microwave-induced injury on the skin encompasses a wider range of possible effects, making it a better-understood phenomenon.
Excessive heating of internal organs, such as the liver, can occur due to microwave exposure, but the mechanisms and effects are less well-understood than those involving the skin. The skin acts as the first line of defense against microwave radiation, making it more susceptible to injury compared to deeper organs.
To summarize, microwave-induced injury is best understood when it involves the skin, as the skin absorbs microwave radiation and is prone to temperature increases that can cause tissue damage, including squamous cell destruction. Other effects of microwaves, such as excessive heating of internal organs, are less well-understood, making the skin the primary focus of study for this type of injury.

For more information on  squamous cells see:

https://brainly.com/question/30489088

#SPJ11

The (326-2) Type IGS cable is an excellent choice for high-voltage applications where flexibility and reliability are key factors. It is particularly well-suited for use in power transmission and distribution applications where it can help to improve system efficiency and reduce maintenance costs.

The (326-2) Type IGS cable is a factory assembly of one or more conductors, each individually insulated and enclosed in a loose fit nonmetallic flexible conduit. This type of cable is specifically designed as an integrated gas spacer cable and is rated for use up to 35,000 volts.

The nonmetallic conduit used in the IGS cable provides a high degree of flexibility and allows for ease of installation, particularly in challenging environments. Additionally, the integrated gas spacer technology provides enhanced electrical performance by minimizing electrical stress, reducing the risk of corona discharge, and improving the overall reliability of the cable.

To learn more about Voltage :

https://brainly.com/question/1176850

#SPJ11

For a 50 ampere circuit listed for use at 75 degrees Celsius, a #6 THHN conductor is required.

To determine the size of the THHN conductor required for a 50-ampere circuit listed for use at 75 degrees C, we need to consult the NEC (National Electric Code) Table 310.16, which provides ampacity ratings for different sizes of conductors at different temperatures.

According to Table 310.16, a 50-ampere circuit requires a minimum of #6 AWG THHN conductor for use at 75 degrees C.

It's important to note that this answer assumes certain conditions, such as a single-phase, 120/240V circuit, and other factors that may affect conductor sizing. It's always best to consult the NEC and local codes, as well as a qualified electrician, to ensure proper conductor sizing and installation for a specific application.

To learn more about conductor, refer:-

https://brainly.com/question/8426444

#SPJ11

The light from the sun dry the glue when light from the desk lamp does not because the sun gives off a type of light that carries energy, and light from the desk lamp does not.

Option c is correct.

The sun emits a broad spectrum of light, including ultraviolet (UV) light, which carries more energy than visible light from a desk lamp.

When the UV light from the sun hits the glue it  causes chemical reactions that result in the drying of the glue.

So we know that the light from the desk lamp may not have the right type of energy to initiate the necessary chemical reactions for the glue to dry.

Learn more about the sun at: https://brainly.com/question/15837114

#SPJ1

The given statement, "It is believed by some researchers that the hazards of low level radiation may be worse than previously predicted, supporting the principle that "x-rays should be used only when there is good medical reason." is true because a lot of research is being done to determine the biological causes of radiation damage to DNA and cells.

Ionizing radiation has always been a risk to human populations, but it is now even more prevalent because of its usage in agriculture, industry, and the military forces. While the health dangers from medium and high doses of radiation are generally established, those from lower levels are less so.  Confusion has been caused for the public as well as for decision-makers by conflicting messages on the safety of low doses of radiation from various sources.  

To know more about researchers

https://brainly.com/question/17181096

#SPJ4

As the mass is lowered, the potential energy of the system is decreased, but it is converted into kinetic energy.

When the mass is lowered, the potential energy of the system is decreased. As the mass is pulled down, the spring is stretched further, which increases the potential energy stored in the spring. When the mass is released, it starts oscillating and the potential energy of the spring is converted into kinetic energy of the oscillating mass. As the mass moves downwards, it loses potential energy and gains kinetic energy, and vice versa as it moves upwards. So, as the mass is lowered, the potential energy of the system is decreased, but it is converted into kinetic energy.

When the mass hanging vertically at the end of a spring is pulled downward and released, the potential energy of the system is increased. This is because, as the mass is lowered, the spring is stretched, and the potential energy stored in the spring (elastic potential energy) increases. When the mass is released, this stored energy is converted into kinetic energy, causing the mass to oscillate.

Visit here to learn more about kinetic energy  : https://brainly.com/question/26472013
#SPJ11

To determine the size conductor required to supply a 40 ampere non-continuous load in a raceway that contains four current-carrying conductors, you will need to consult the NEC (National Electrical Code) tables for conductor ampacity.

Based on the NEC tables, for four current-carrying conductors in a raceway, you will need a conductor rated for at least 70 amperes. Therefore, a 6 AWG (American Wire Gauge) copper conductor would be suitable for supplying a 40 ampere non-continuous load in this scenario. It is important to note that this answer assumes that the installation meets all other code requirements, such as proper wire insulation and protection.

To know more about National Electrical Code click here:

https://brainly.com/question/17215290

#SPJ11

The vertical distance an object dropped from rest on this distant planet covers in 1.3 seconds is 18.59 meters.

To calculate the vertical distance an object dropped from rest on this distant planet covers in 1.3 seconds, we can use the following equation of motion:
d = vi * t + 0.5 * a * t^{2}
where d is the vertical distance, vi is the initial velocity (0 m/s, since the object is dropped from rest), a is the acceleration (22 m/s^{2}), and t is the time (1.3 s).
Step 1: Substitute the given values into the equation:
d = 0 * 1.3 + 0.5 * 22 * (1.3)^{2}
Step 2: Perform the calculations:
d = 0 + 0.5 * 22 * 1.69
d = 11 * 1.69
Step 3: Calculate the final value:
d ≈ 18.59 m
So, the object dropped from rest on this planet with an acceleration of 22 m/s^{2} covers a vertical distance of approximately 18.59 meters in 1.3 seconds.

learn more about acceleration Refer: https://brainly.com/question/30660316

#SPJ11

The air-to-air heat pump adds heat from the outside air and deposits it in the conditioned space. The correct answer is. An air-to-air heat pump (a) adds heat from the outside air and deposits it in the conditioned space.

The air-source or air-to-air heat pump can provide both heating and cooling. In the winter, a heat pump extracts heat from outside air and delivers it indoors. On hot summer days, it works in reverse, extracting heat from room air and pumping it outdoors to cool the house. In the winter, a heat pump extracts heat from outside air and delivers it indoors. On hot summer days, it works in reverse, extracting heat from room air and pumping it outdoors to cool the house Nearly all air-source and air-to-air heat pumps are powered by electricity. They have an outdoor compressor/ condenser unit that is connected with refrigerant-filled tubing to an indoor air handler. As the refrigerant moves through the tubing of the system, it completes a basic refrigeration cycle, warming or cooling the coils inside the air handler. The blower pulls in room air, circulates it across the coils, and pushes the air through ductwork back into rooms.

learn more about air-to-air heat pump here.

https://brainly.com/question/1081420

#SPJ11

c. Incinerators are rated in terms of tons of burnable waste per day. This rating helps to determine the capacity of the incinerator and the amount of waste it can safely and efficiently dispose of.

Incinerators are waste management facilities that use controlled combustion to thermally treat and dispose of solid and liquid waste. They are designed to burn and convert waste into ash, gases, and heat.

The process of incineration involves loading the waste into a furnace or combustion chamber, where it is subjected to high temperatures of up to 1000-1200°C. The heat generated during the process is used to evaporate and remove any moisture present in the waste, and then to initiate and sustain combustion.

The waste is burned and converted into ash, gases, and heat. The ash is collected and disposed of in landfills, while the gases produced during the process are typically treated before being released into the atmosphere.

Incineration can be used to treat a variety of waste streams, including medical and hazardous waste, municipal solid waste, sewage sludge, and industrial waste. It has several advantages, such as reducing the volume of waste, generating energy, and reducing the need for landfill space.

However, incineration also has several environmental and health concerns. The release of pollutants and toxic substances during the process, such as dioxins, furans, and heavy metals, can have harmful effects on human health and the environment. Therefore, the operation of incinerators is strictly regulated and subject to emission standards to ensure that they do not pose a threat to public health and the environment.

Find out more about Incinerators

brainly.com/question/31293434

#SPJ11

The statement" counters can count past their preset values" is regarded to be true. This is known as overflow, where the counter will continue counting from zero after it has reached its maximum preset value.

It is true that counters can count past their preset values. In many systems, once a counter reaches its preset value, it resets to its initial state and continues counting from there. This process is called overflow or rollover, and it allows counters to keep track of counts beyond their preset limits.

More on counters: https://brainly.com/question/30784277

#SPJ11

A pitching moment is produced when there is a difference in pressure on the top and bottom surfaces of an airfoil. The pressure difference creates a torque around the aircraft's lateral axis, causing the aircraft to pitch up or down.

In other words, any situation that causes a difference in lift between the two wings or between the front and rear of the aircraft will produce a pitching moment.
Therefore, option A, a camber airfoil that is developing zero lift, will not produce a pitching moment since there is no difference in pressure between the top and bottom surfaces. Option B, a camber airfoil at a positive angle of attack, will produce a pitching moment since the difference in pressure between the top and bottom surfaces increases as the angle of attack increases. Option C, a symmetrical airfoil at a zero AOA, will not produce a pitching moment since the airfoil has no camber and there is no difference in pressure between the top and bottom surfaces.
In summary, a situation where there is no difference in pressure between the top and bottom surfaces of an airfoil will not produce a pitching moment.

learn more about pressure here

https://brainly.com/question/3371255

#SPJ11