10) Explain which substance(s) would you expect to be a gas at standard
temperature and pressure (STP).
NI3
BF3
PC13
A) BF3
Its molecules are nonpolar and, therefore, are subject only to
dispersion forces.
B) NI3
Its molecules are polar and possess dipole-dipole interactions
therefore allowing them to exist as a gas.
C) PCL3
Its molecules are slightly polar and, therefore, possess dipole-
dipole interactions. However, they are weak enough to allow it
to exist as a gas.
D) Nlz and BF3
Both molecules are very light in mass. Therefore, they have
weak dispersion forces which causes them to be attracted very
weakly and exist as a gas.

Answer:

Forged parts are often tougher than cast parts. This can be determined by performing tensile tests on various areas on the parts. Additionally, the microstructures of forged and cast parts can be used to determine if a part was forged or cast. The microstructure of a cast part will have a more uniform grain structure.

Explanation:

Answer:

natural materials like cotton

-Sound waves transfer energy by the motion of particles.

Explanation:

These particle-to-particle, mechanical vibrations of sound conductance qualify sound waves as mechanical waves. Sound energy, or energy associated with the vibrations created by a vibrating source, requires a medium to travel, which makes sound energy a mechanical wave.

Sound waves transfer energy by the motion of particles considered a type of mechanical energy.

Potential energy plus kinetic energy are combined to form mechanical energy. According to the concept of mechanical energy conservation, mechanical energy remains constant in an isolated system that is solely exposed to conservative forces.

The quantity of energy that a force transfers is known as mechanical work. It is a scalar quantity with joules as its SI unit, much as energy.

Since there are only microscopic forces generated by atomic collisions and no macroscopically quantifiable force, heat conduction is not regarded as a kind of work.

Transverse, longitudinal, and surface waves are the three different forms of mechanical waves. When the wave's energy goes through them, they behave differently in terms of how the medium's particles move.

Thus, option C is correct.

To learn more about mechanical energy follow the link;

https://brainly.com/question/1932868

#SPJ2

The maximum chemical amount in moles of Ni₂ (aq) that can be released into the solution is 0.978 mol.

Using Q = nF where Q = quantity of electricity = 9.439 × 10⁴ C = 94390, n = number of moles of NI₂ (aq) and F = Faraday's constant = 96485 C/mol

Making n subject of the formula, we have

n = Q/F

substituting the values of the variables into the equation, we have

n = Q/F

n = 94390 C/96485C/mol

n = 0.978 mol

So, the maximum chemical amount in moles of Ni₂ (aq) that can be released into the solution is 0.978 mol.

Learn more about electrolysis here:

https://brainly.com/question/10692990

Answer:

The key to understanding why ionic and covalent compounds have different properties from each other is understanding what's going on with the electrons in a compound. Ionic bonds form when atoms have different electronegativity values from each other. When the electronegativity values are comparable, covalent bonds form.

But, what does this mean? Electronegativity is a measure of how easily an atom attracts bonding electrons. If two atoms attract electrons more or less equally, they share the electrons. Sharing electrons results in less polarity or inequality of charge distribution. In contrast, if one atom attracts bonding electrons more strongly than the other, the bond is polar.

Ionic compounds dissolve in polar solvents (like water), stack neatly on each other to form crystals, and require a lot of energy for their chemical bonds to break. Covalent compounds can be either polar or nonpolar, but they contain weaker bonds than ionic compounds because they are sharing electrons. So, their melting and boiling points are lower and they are softer.

I hope this helps have a great day :)

Since gas molecules average velocity depends on temperature, oxygen molecules at 25°C are moving faster than oxygen molecules at 0 °C.

According to the kinetic theory of gases, the molecules of a gas are in constant random motion and collide frequently with each other and the walls of the container.

The average speed of gas molecules depends on temperature and molar mass as shown by the relation;

vrms = √3RT/M

The following statement are true among the options provided;

The following are false among the options provided;

Learn more: https://brainly.com/question/6505878

Answer:

A. because there both high pitched voice and low pitched ( girls have sweet, shrill ,high pitched good voice ) where as boys have horase ,low pitched medium voice )

Waste is removed from the body in various ways. Kidneys filter out metabolic waste, excess fluid and eliminate it in the form of urine. Lungs exhale CO2 from the deoxygenated blood. The undigested solid waste is egested out from the large intestine. Excretion is the process of removing wastes and excess water from the body. It is one of the major ways the body maintains homeostasis. Organs of excretion make up the excretory system. They include the kidneys, large intestine, liver, skin, and lungs.

Answer:

dilute solution

A solution containing less solute than the equilibrium amount is called a dilute solution. The solvent has a limited capacity to dissolve a solute.

Explanation:

Answer:

1.false

2.true

3.true

4.true

5.false

6.false

7.false

8.true

9.false

10.true

Explanation:

I took the test

Answer:  251 K

Explanation: hope this helps :)

Answer:  a.1.37  b.4.11 c.6.00  d.12.3

Explanation:

Answer:

In summary, yeast is a single-celled fungus that uses cellular respiration, which converts glucose and oxygen into carbon dioxide and ATP. ... Aerobic respiration makes the most ATP, between 36 and 38. Fermentation is anaerobic respiration and happens without oxygen.

% Composition of elements:

Atomic mass of given elements:

Now, divide % composition by Atomic mass:

[tex]\footnotesize\implies Mg = \dfrac{\% \: Composition}{Atomic \: mass} = \dfrac{75}{24} = \bf 3.125[/tex]

[tex]\footnotesize\implies O = \dfrac{\% \: Composition}{Atomic \: mass} = \dfrac{25}{16} = \bf 1.5625[/tex]

Simplest Ratio:

[tex]\footnotesize\implies Mg = \dfrac{3.125}{1.5625} = 2[/tex]

[tex]\footnotesize\implies O = \dfrac{1.5625}{1.5625} = 1[/tex]

Empirical Formula:

[tex]\footnotesize\implies \underline{ \boxed{ \red{ \bf Empirical \: Formula = Mg_2O}}}[/tex]

The empirical formula will be [tex]Mg_{2}[/tex] .

The simplest entire number fraction of atoms contained in a chemical molecule is its empirical formula.

Calculation of empirical formula:

It is given that, composition of Mg = 75 %, composition of oxygen  = 25%.

It is known that, atomic mass of Mg = 24 g, atomic mass of oxygen = 16g.

By dividing % composition by atomic mass of given elements:

Mg = % composition / %atomic mass

= 75 / 24

= 3.125

Oxygen (O) = % Composition / atomic mass

= 25 / 1.56

Now, calculate simplest ratio of Mg and O.

For Mg = 3.125 / 1.56

= 2.

For O = 1.56 / 1.56

= 1

So, the empirical formula will be [tex]Mg_{2}O[/tex].

To know more about empirical formula.

https://brainly.com/question/14044066.

#SPJ2

Answer:

Use the formula PV=nRT to get the temperature

Answer:

933.33 m/ min

Explanation:

1 mile = 1.6 km

So the car travels 1.6× 35 km in 1 hour

One hour has 60 minutes

So speed of car = 1.6×35 km / 60 minutes

1km = 1000 m

Speed = 1.6×35×1000 m/ 60 minutes

= 933.33 meters per minute

A car is traveling 35 miles per hour. The speed that is measured in meters per minute is 933.33 m/ min.

Speed is the dimension of distance. It is calculated in meters per second. It is the rate of change of an object in a direction. Speed is calculated by dividing the distance by time. It is a scalar quantity.

Given, that a car is traveling 35 miles per hour. The speed is given, in miles we just have to convert the miles into meters per minute. Miles if the English unit of measurement and meter is the SI unit of measurement.

1 mile = 1.6 km

So the car travels 1.6× 35 km in 1 hour

One hour has 60 minutes

So speed of car = 1.6×35 km / 60 minutes

1km = 1000 m

Speed = 1.6 × 35 × 1000 m/ 60 minutes

= 933.33 meters per minute

Thus, the speed of the car is 933.33 m/ min.

To learn more about speed, refer to the link:

https://brainly.com/question/7359669

#SPJ2

Answer:

During __asexual________ reproduction, an identical copy of the parent is produced.

Answer:

HowHow many moles of KOH are in 21.0g of KOH?

Answer:

0.374 moles

Explanation:

I have included the dimensional analysis below, and by MM I mean Molar Mass of the atom.

Hope this helps!

Answer:

The partial pressure of water is much less than 1atm, so the free energy change for the process must be negative with ΔGrxn<0.

Explanation:

Water vapor will condense into liquid water when the water vapor is in its standard state, with a pressure of 1atm. Under normal circumstances, the partial pressure of water vapor is much less that 1atm. It is in a nonstandard state. The free energy change of this reaction has to be negative in order to make the reaction spontaneous.

The criteria of the spontaneous process are the change in the Gibbs free energy should be negative. Above the normal boiling point, the TΔS will be greater than ΔH and ΔG<0.

Gibbs free energy can be described as a state function therefore it doesn’t depend on the path. The change in free energy is equal to the change in enthalpy minus the product of entropy change and temperature of the system.

ΔG = ΔH - Δ (TS)

If the process is carried out at constant temperature, ΔT = 0:

ΔG = ΔH – TΔS

ΔG > 0 for the reaction is non-spontaneous, ΔG < 0 for the reaction is spontaneous, exergonic and ΔG = 0 for the reaction is at equilibrium.

Spontaneous can be described as a reaction that occurs by itself without any external action towards it. The non-spontaneous process needs constant external energy applied to continue and as the external action, the process will cease.

Learn more about Gibbs free energy, here:

https://brainly.com/question/9179942

#SPJ5

Answer: the answer is c.

Explanation:

i juss guessed and it was right?

52

Explanation:

70x45÷60= 52

I hope this is helpful

Answer:

True.

Explanation:

Since electromagnetic radiation travels in waves, we can assume that the more high energy the waves are, the faster they will go. So therefore, higher energy travels faster.

Hope that helps you!

Answer:

True

Explanation:

Answer:

because water is actually a limited natural resource

Explanation:

although most of the earth is made up of water , dasalination plants are super expensive and hard to use. Thus slowly due to severely low rainfall over the years the earth is slowly depleting on levels of fresh water thats why we need to be careful how we use water :D !

Answer:

Aluminium reusable water bottle Purpose of aluminum: Weighs less by volume than most other metals and comes at an affordable price.

Explanation:

Nutmeg

Nubbing

Notifying

Neezing

Nudging

Needing

Niffing

Narcotizing

Nanjing

Neighbouring

Nothing

Nimming

Neighboring

Netting

Nesting

Narcing

Nitpicking

Non-Living

Neutralizing

Nightwalking

Nonspeaking

Answer:

The answer is option A

Explanation:

This is because the measure from crest to crest is also known as the wavelength, and the color of a wave always depends on its wavelength, if you see the electromagnetic spectrum

Hope this helps!

In the formation of 1 formula unit of ScBr₃, 3 electrons are transferred.

Let's consider the following balanced redox reaction.

2 Sc + 3 Br₂ ⟶ 2 ScBr₃

We can identify both half-reactions.

Oxidation: 2 Sc ⟶ 2 Sc⁺³ + 6 e⁻

Reduction: 6 e⁻ + 3 Br₂ ⟶ 6 Br⁻

As we can see, 6 electrons are involved in the formation of 2 formula units of ScBr₃. Thus, 3 electrons are involved in the formation of 1 formula unit of ScBr₃.

In the formation of 1 formula unit of ScBr₃, 3 electrons are transferred.

Learn more: https://brainly.com/question/23331785

Answer:

Ba(OH)2 + 2 HCl → BaCl2 + 2 H2O

The reactants are present in equimolar amounts, so there is no excess or limiting reactants.

(0.0500 L) x (0.600 mol/L HCl) x (2 mol H2O / 2 mol HCl) = 0.0300 mol H2O

(4.184 J/g·°C) x (50.0 g + 50.0 g) x (25.82 - 21.73)°C = 1711.256 J

(1711.256 J) / (0.0300 mol H2O) = 57042 J/mol = 57.0 kJ/mol H2O

Explanation: